RAD-MIB Table View

Table-centric layout grouping table, row, and column objects.

MIB version

Standard view Table view

Tables

622

Rows

622

Columns

5,673

segTRTable

table

.1.3.6.1.4.1.164.1.1.3.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk segTRTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::segTRTable'

Segments.

segTREntry row .1.3.6.1.4.1.164.1.1.3.1.1

An entry in table segTRTable.

Indexes

No indexes recorded

Column Syntax OID

segTRID

Segment unique identification number (internal). It is
the extreme left slot, marking the beginning of the
segment.

Integer32

.1.3.6.1.4.1.164.1.1.3.1.1.1

segTRLastSlot

Location of the right most slot marking the end of the
segment. In the RADring hub it is slot number 20 or the slot
where end of segment module is inserted or the slot before
a beginning of a new segment. ( End of seg…

SNMPv2-SMIInteger32

Enumerated Values:

1	unknown
2	fourMegabit
3	sixteenMegabit
4	tenMegabit

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.1.1.3.1.1.2

segTRFirstSlot

Location of the left most slot marking the beginning
of the segment. In the RADring hub it is slot number 1 or
the slot number following the end of segment module, or where
a repeater or TIO is inserted.

SNMPv2-SMIInteger32

Enumerated Values:

1	unknown
2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.1.1.3.1.1.3

segTRStatus

Describes the status of the segment :
Normal(3) - The segment is operating normally
Beaconing(2) - The ring is not operative; no data is transmitted.
Segment without inband module within its limit will display Unknown(1…

Enumeration

Enumerated Values:

1	notApplicable
2	off
3	on

.1.3.6.1.4.1.164.1.1.3.1.1.4

mdlTRTable

table

.1.3.6.1.4.1.164.1.1.4.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlTRTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlTRTable'

Modules parameters structure
contains general information about the modules.

mdlTREntry row .1.3.6.1.4.1.164.1.1.4.1.1

An entry in table mdlTRTable.

Indexes

No indexes recorded

Column Syntax OID

mdlTRID

The slot number where the module is inserted. Can not be greater
than chNoSlot

SNMPv2-SMIInteger32

Enumerated Values:

1	unknown
2	empty
3	tl4s
4	tl4su
5	tl4sd
6	tl4cx
7	tl4u
8	tl2edu
9	tl2eds
10	tl2edsu
11	tl2f
12	tja
13	tio
14	tfr
15	tfc1
16	tfc2
17	tcr
18	tl4au
19	tl4as
20	tl4asd
21	tl4asu
22	tre1d
23	tre
24	tre8d
25	stc1
26	stc2
27	ftc
28	cmlib
29	tl2fsat
30	taV24
31	taV11
32	wangVs
33	ta3x74
34	ta3x
35	sat-asu
36	sat-asd
37	sat-su
38	sat-sd
39	ep8t
40	ep4taui
41	ep4t2fl
42	ep4tfl
43	ep4fl
45	epr8t
46	epr4taui
47	epr4t2fl
48	epr4tfl
49	epr4fl
51	tl2fm
53	ftc2
54	mlbt
55	mlbtf
56	ftbDfo
57	ftbSfo
58	mbe8d
59	mbe1d
60	cmlibE

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.1.1.4.1.1.1

mdlTRSegID

The segment number where the module belongs to. One of the
segTRID values.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.1.1.4.1.1.2

mdlTRTypedeprecated

Indicates the type of the module connected at the specified slot number.

Enumeration

.1.3.6.1.4.1.164.1.1.4.1.1.3

mdlTRHwVer

ASCII string for description and display of the module's hardware version,
as it is known by the module's software. A manager can record his own
hardware upgrade.

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.1.1.4.1.1.4

mdlTRSwVer

ASCII string for description and display of the module's
software version. A value of NOT APPLICABLE will be recorded
for module having no independent processor.

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.1.1.4.1.1.5

mdlTRTotalNoOfPrt

This entry describes the number of possible ports/lobes/links
connection in the module (not all ports hardware should be active) .

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.1.1.4.1.1.6

mdlTRSpecific

Object identifier of entity containing additional information
regarding this instance. This entry is type specific.

ObjectIdentifier

Constraints:
range: 1-20

.1.3.6.1.4.1.164.1.1.4.1.1.7

prtTRTable

table

.1.3.6.1.4.1.164.1.1.5.1 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtTRTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtTRTable'

TReral port table for any media type.

prtTREntry row .1.3.6.1.4.1.164.1.1.5.1.1

An entry in table prtTRTable.

Indexes

No indexes recorded

Column Syntax OID

prtTRModuleID

A unique identifier of the module(slot no.)this port is attached to.

SNMPv2-SMIInteger32

Enumerated Values:

2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.1.1.5.1.1.1

prtTRID

A unique identifier of the port within its module.

SNMPv2-SMIInteger32

Enumerated Values:

1	notStarted
2	started
3	segmentOk
4	segmentFixed
5	segmentClosed
6	failed
7	hubProblem

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.1.1.5.1.1.2

prtTRFunctionality

Describes the functionality of the port in a Token ring topology or other implementations.

Enumeration

Enumerated Values:

1	noOp
2	open
3	reset
4	close

.1.3.6.1.4.1.164.1.1.5.1.1.3

prtTRConnectorType

Type of hardware connector in the port.

Enumeration

Enumerated Values:

1	unknown
2	opened
3	closed
4	opening
5	closing
6	badParam
7	lobeFailed
8	signalLoss
9	insertionTimeout
10	ringFailed
11	beaconning
12	duplicateMac
13	requestFailed
14	removeReceived
15	budFailure
16	initFailure

.1.3.6.1.4.1.164.1.1.5.1.1.4

prtTRAdminCmd

By setting this attribute to DISABLE(2) or SHORT(4) the
management station can force this lobe/port/link-connection to be
removed and block any access to the network via this lobe/port/link.
It is not mandatory th…

Enumerationr/w

Enumerated Values:

2	off
3	on
4	standBy

.1.3.6.1.4.1.164.1.1.5.1.1.5

prtTRActiveState

This attribute describes the electrical or optical activity
state of a lobe or the state of a port. Certain values may
not be applicable in some cases

Enumeration

.1.3.6.1.4.1.164.1.1.5.1.1.6

prtTRTrapMaskEnable

When this attribute is set to OFF by the management console the
agent starts sending the unmasked traps related to this port.
Otherwise no traps from this port are sent.

Enumerationr/w

.1.3.6.1.4.1.164.1.1.5.1.1.7

prtTRstatus

This attribute indicates the status of this lobe/port
connection:
DISABLED - (2) to (6) indicates the reason for the disabled state.
INSERTED - (7)indicates that the lobe hardware inserts this lobe
into the…

Enumeration

Enumerated Values:

1	unknown
2	off
3	on

.1.3.6.1.4.1.164.1.1.5.1.1.8

prtTRCableProtectEnable

The value of this attribute determines activation of the cable-fault
protection mechanism of TCR and the optical link mechanism of
TFR and TFC .

Enumeration

.1.3.6.1.4.1.164.1.1.5.1.1.9

prtTRCableState

The value of this attribute determines the cable status
of TCR and the optical link mechanism of
TFR and TFC .

Enumeration

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.1.1.5.1.1.10

prtTRMACAddress

The value of this object is the specific MAC address
of this interface which uniquely identifies this Interface
on a ring.

MacAddress

Type Constraints:
range: 6

.1.3.6.1.4.1.164.1.1.5.1.1.11

prtTRSpecific

Object identifier of entity containing additional information
regarding this instance. This entry is type specific.

ObjectIdentifier

.1.3.6.1.4.1.164.1.1.5.1.1.12

prtTRMacAddressTable

table

.1.3.6.1.4.1.164.1.1.5.2 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtTRMacAddressTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtTRMacAddressTable'

prtTRMacAddressEntry row .1.3.6.1.4.1.164.1.1.5.2.1

An entry in table prtTRMacAddressTable.

Indexes

No indexes recorded

Column Syntax OID

prtTRMacAddressModuleID

A unique identifier of the module(slot no.)this port is attached to.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.1.1.5.2.1.1

prtTRMacAddressPortID

A unique identifier of the port within its module.

SNMPv2-SMIInteger32

Enumerated Values:

1	unknown
2	main
3	remote
4	secondary

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.1.1.5.2.1.2

prtTRMacAddressID

A identifier of the MAC address in the list according to the ring order

Integer32

.1.3.6.1.4.1.164.1.1.5.2.1.3

prtTRMACAddressValue

MAC address from the list of addresses connected to this port

MacAddress

Type Constraints:
range: 6

.1.3.6.1.4.1.164.1.1.5.2.1.4

segRRSecurityTable

table

.1.3.6.1.4.1.164.1.2.2.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk segRRSecurityTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::segRRSecurityTable'

RADRing segments' specific information

segRRSecEntry row .1.3.6.1.4.1.164.1.2.2.1.1

An entry in table segRRSecurityTable.

Indexes

No indexes recorded

Column Syntax OID

segRRID

Segment unique identification number (internal). It is
the extreme left slot, marking the beginning of the
segment.
TR segment no.: 1 .. 20
Ethernet segment no.: 21.

Integer32

.1.3.6.1.4.1.164.1.2.2.1.1.1

segRRSecID

Segment's security unique identification number

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.1.2.2.1.1.2

segRRSecEnable

This entry indicates whether the specific segment's security is active or not

Enumerationr/w

Constraints:
range: 1-20

.1.3.6.1.4.1.164.1.2.2.1.1.3

segRRSecurityPattern

A six-octet (48 bit) pattern, where the masked bits of segTRSecurityMask
need to match the MAC address of each port within the segment. A Value of
all-zeros indicates no security.

MacAddressr/w

Enumerated Values:

1	unknown
2	off
3	on

Type Constraints:
range: 6

.1.3.6.1.4.1.164.1.2.2.1.1.4

segRRSecurityMask

Mask of the allowed MAC address that can be connected through
the ports within the segment

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.1.2.2.1.1.5

mdlRRTable

table

.1.3.6.1.4.1.164.1.2.3.1 · 1 row entry · 14 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlRRTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlRRTable'

RADRing  specific modules' information

mdlRREntry row .1.3.6.1.4.1.164.1.2.3.1.1

An entry in table mdlRRTable.

Indexes

No indexes recorded

Column Syntax OID

mdlRRid

Unique number to identify the module. It indicates the slot
number the module is inserted in.

Integer32

Enumerated Values:

1	unknown
2	off
3	on

.1.3.6.1.4.1.164.1.2.3.1.1.1

mdlRRTLRstatus

This entry specifies the status of the setup on the TL-2/Exx
modules. When the value is ON, lobe one is the only active lobe. This entry
will have the value UNKNOWN for all other modules

Enumeration

.1.3.6.1.4.1.164.1.2.3.1.1.2

mdlRRtermination

Attribute describing the termination state as set by the switches on the
lobe modules

Enumeration

.1.3.6.1.4.1.164.1.2.3.1.1.3

mdlRRReset

When this object is set to the value of ON(3),
the module performs software reset. Upon completion, a trap will
be issued to the management station and the value
will be set to OFF. This entry will have the value of U…

Enumerationr/w

.1.3.6.1.4.1.164.1.2.3.1.1.4

mdlRRLed

This entry specifies the LEDs status in the module . Each led will be represented by 4 bits
where the first 2 bits will specify the status (NA, OFF, ON, BLINK), and the next two bits
will specify the color (RED, GREEN…

OctetString

.1.3.6.1.4.1.164.1.2.3.1.1.5

mdlRRSpeed

Attribute describing the bandwidth of the media as set by the module switches.

Enumeration

Enumerated Values:

1	notactive
2	active

.1.3.6.1.4.1.164.1.2.3.1.1.6

mdlRRMngAutoDisobsolete

Attribute describing the setup of the MNG switch on the TL- Active cards. Value ON indicates
the ability of activating the auto-disable mechanism of the card via management command.
Value OFF indicates that the ac…

Enumeration

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.1.2.3.1.1.7

mdlRRAutodisable

This attribute can be set by the manager if the value of mdlRRMngAutoDis is ON. It
controls the behavior of the Active cards regarding the Auto-disable mechanism. All
ports will be in the same mode. Applicable to Tok…

Enumerationr/w

.1.3.6.1.4.1.164.1.2.3.1.1.8

mdlRRConfigMsg

Full configuration message coded in internal RAD application format.
This entry describes module' configuration.

OctetString

.1.3.6.1.4.1.164.1.2.3.1.1.9

mdlRRMngState

This entry indicates the setting of the module's switches. ENABLE means that the module
can accept management commands.

Enumeration

Enumerated Values:

1	unknown
2	off
3	on

.1.3.6.1.4.1.164.1.2.3.1.1.10

mdlRRType

Indicates the type of the module installed in the specified slot number.

Enumeration

.1.3.6.1.4.1.164.1.2.3.1.1.11

mdlRRHwVer

ASCII string for description and display of the module's hardware version,
as it is known by the module's software. A manager can record his own
hardware upgrade.

SNMPv2-TCDisplayStringr/w

Enumerated Values:

1	noApplicable
2	off
3	on

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.1.2.3.1.1.12

mdlRRSwVer

ASCII string for description and display of the module's
software version. A value of NOT APPLICABLE will be recorded
for a module having no independent processor.

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.1.2.3.1.1.13

mdlRRSpecific

Object identifier of entity containing additional information
regarding this instance. This entry is module type specific.

ObjectIdentifier

.1.3.6.1.4.1.164.1.2.3.1.1.14

mdlIBTable

table

.1.3.6.1.4.1.164.1.2.3.2 · 1 row entry · 13 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlIBTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlIBTable'

Additional parameters that can be monitored for a segment
with an inband module. Module specific for Token Ring

mdlIBEntry row .1.3.6.1.4.1.164.1.2.3.2.1

An entry in table mdlIBTable.

Indexes

No indexes recorded

Column Syntax OID

mdlIBid

Unique number to identify the CML\IB module. It indicates the slot
number the module is inserted in

Integer32

.1.3.6.1.4.1.164.1.2.3.2.1.1

mdlIBsegID

Unique number to identify the segment where the CML\IB module
is inserted. It is one of the segTRID values.

Integer32

.1.3.6.1.4.1.164.1.2.3.2.1.2

mdlIBCorrelationEnable

When set to ON(3), the in-band agent should perform
correlation each time a station enters/leaves the segment.

Enumerationr/w

.1.3.6.1.4.1.164.1.2.3.2.1.3

mdlIBAutorecEnable

When set to ON(3), the in-band agent should perform
autorecovery each time a beacon status is detected.

Enumerationr/w

.1.3.6.1.4.1.164.1.2.3.2.1.4

mdlIBAutorecResult

When autorecovery is completed the result will be reported (3)..(7).
While in autorecovery process, started(2) will be reported.
Before autorecovery process, notStarted(1) will be reported.

Enumeration

Enumerated Values:

1	normal
2	locLoop
3	remLoop

.1.3.6.1.4.1.164.1.2.3.2.1.5

mdlIBcommand

When this object is set to the value of
open(2), the station should go into the
open state. The progress and success of
this command is given by the values of the
object mdlIBstate.
When this object is set to the v…

Enumerationr/w

Enumerated Values:

1	operational
2	locSyncLoss
3	remSyncLoss

.1.3.6.1.4.1.164.1.2.3.2.1.6

mdlIBstate

The current adapter status, which can
be used to diagnose fluctuating problems.

Enumeration

Enumerated Values:

1	normal
2	locLoop
3	remLoop
4	bert

.1.3.6.1.4.1.164.1.2.3.2.1.7

mdlIBagnt

Indicates whether the specific inband module serves as:
- Active hub agent - (on)
- Ring Monitor (for TR module only) - (off)
- Standby agent - (standBy)

Enumeration

Enumerated Values:

1	unknown
2	fault
3	ok

.1.3.6.1.4.1.164.1.2.3.2.1.8

mdlIBIpAddress

Indicates IP address of the module if the module serves as
an agent of itself.

RFC1155-SMIIpAddress

Enumerated Values:

2	off
3	on

Type Constraints:
range: 4

.1.3.6.1.4.1.164.1.2.3.2.1.9

mdlIBLocalMacAddr

The value of this object is the specific MAC address
of this interface which uniquely identifies this interface
on a ring.It is the address set by the management and
upon request it will replace the burn in address.
…

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.1.2.3.2.1.10

mdlIBLocalAddrStatus

The value of this object specifies whether the specific
MAC address of this interface was set by the local
management or it is the burn-in address in use.

Enumerationr/w

.1.3.6.1.4.1.164.1.2.3.2.1.11

mdlIBbrnInMacAddr

The value of this object is the specific Burn-in MAC address
of this interface which uniquely identifies this interface
on a ring. Non-canonical format.

MacAddress

Type Constraints:
range: 6

.1.3.6.1.4.1.164.1.2.3.2.1.12

mdlIBTrapMaskEnable

When this attribute is set to OFF by the management console, the
agent starts sending the unmasked traps related to this module.
Otherwise, no traps are sent by this module.

Enumerationr/w

.1.3.6.1.4.1.164.1.2.3.2.1.13

mdlBRGTable

table

.1.3.6.1.4.1.164.1.2.3.3 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlBRGTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlBRGTable'

Special modules such as bridges/converters  that are within the hub

mdlBRGEntry row .1.3.6.1.4.1.164.1.2.3.3.1

An entry in table mdlBRGTable.

Indexes

No indexes recorded

Column	Syntax	OID
mdlBRGid Unique number to identify the module. It indicates the slot number the module is inserted in.	Integer32	`.1.3.6.1.4.1.164.1.2.3.3.1.1`
mdlBRGReady This entry will have the value ON when packets can be transferred in the TRE module. The value UNKNOWN will be used for all other modules where this characteristic is not applicable	Enumeration	`.1.3.6.1.4.1.164.1.2.3.3.1.2`
mdlBRGStatus This entry specifies the status of operation of the STC or FTC modules. For other modules this value will read NOAP	SNMPv2-TCDisplayString Type Constraints: `range: 0..255` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.164.1.2.3.3.1.3`
mdlBRGLocation This entry indicates the configuration mode: - for the TRE bridge (main/remote) - for MLB-T, MLBT-F (main/secondary)	Enumeration	`.1.3.6.1.4.1.164.1.2.3.3.1.4`
mdlBRGIpAddress Indicates IP address of the module if the module serves as an agent of itself. For all other modules the IP value will be 0.0.0.0	RFC1155-SMIIpAddress Type Constraints: `range: 4`	`.1.3.6.1.4.1.164.1.2.3.3.1.5`
mdlBRGMacAddr The value of this object is the specific MAC address of this interface which uniquely identifies this interface on a ring.	MacAddress Type Constraints: `range: 6`	`.1.3.6.1.4.1.164.1.2.3.3.1.6`
mdlBRGAdapterState The current adapter status, which can be used to diagnose fluctuating problems. This object is applicable only for TR bridges with adapter. The value 'unknown' will be used for other module types.	Enumeration	`.1.3.6.1.4.1.164.1.2.3.3.1.7`
mdlBRGBypassSw This entry is applicable only for FTB-D/FO module. It describes the status of the Bypass Switch. The value UNKNOWN will be used for all other modules where this characteristic is not applicable	Enumeration	`.1.3.6.1.4.1.164.1.2.3.3.1.8`

mdlMMTable

table

.1.3.6.1.4.1.164.1.2.3.4 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlMMTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlMMTable'

Special 'WAN' modules that are within the RadRing hub

mdlMMEntry row .1.3.6.1.4.1.164.1.2.3.4.1

An entry in table mdlMMTable.

Indexes

No indexes recorded

Column Syntax OID

mdlMMid

Unique number to identify the module. It indicates the slot
number the module is inserted in.

Integer32

Enumerated Values:

1	ok
2	faulty

.1.3.6.1.4.1.164.1.2.3.4.1.1

mdlMMBertCmd

Setting this Object to ON, will start BERT test on all the channels that are currently in
Remote Loop. If the value of mdlRRMngState is disabled, this parameter is read-only
and reflects the module…

Enumerationr/w

Enumerated Values:

1	ok
2	faulty

.1.3.6.1.4.1.164.1.2.3.4.1.2

mdlETTable

table

.1.3.6.1.4.1.164.1.2.3.5 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlETTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlETTable'

'Ethernet' modules that are within the hub

mdlETEntry row .1.3.6.1.4.1.164.1.2.3.5.1

An entry in table mdlETTable.

Indexes

No indexes recorded

Column Syntax OID

mdlETid

Unique number to identify the module. It indicates the slot
number the module is inserted in. It is the same
as rptrGroupIndex in the Repeater MIB

Integer32

Enumerated Values:

1	on
2	off
255	notSupported

.1.3.6.1.4.1.164.1.2.3.5.1.1

mdlETSAmode

Setting this Object to ON, will change the mode of operation
of the Ethernet card to a stand alone operation mode. It will
disconnect the card from the repeater bus. The rptrGroupOperStatus
parameter in the Repea…

Enumerationr/w

.1.3.6.1.4.1.164.1.2.3.5.1.2

prtRRTable

table

.1.3.6.1.4.1.164.1.2.4.1 · 1 row entry · 13 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtRRTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtRRTable'

RADRing specific port information

prtRREntry row .1.3.6.1.4.1.164.1.2.4.1.1

An entry in table prtRRTable.

Indexes

No indexes recorded

Column Syntax OID

prtRRmdlID

A unique identifier of the module,(slot no.),this port is attached to.

SNMPv2-SMIInteger32

Constraints:
range: 1-65535

.1.3.6.1.4.1.164.1.2.4.1.1.1

prtRRID

A unique identifier of the port within its module.

SNMPv2-SMIInteger32

Enumerated Values:

1	isolated
2	localA
3	localB
4	localAB
5	localS
6	wrapA
7	wrapB
8	wrapAB
9	wrapS
10	cWrapA
11	cWrapB
12	cWrapS
13	thru

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.1.2.4.1.1.2

prtRRSecurityState

This entry indicates whether a security check can be performed on
the specific port. This value is directly related to the
presence of an inband module in the segment where the port
belongs to and to activation of the …

Enumeration

.1.3.6.1.4.1.164.1.2.4.1.1.3

prtRRSecurityEnable

This value indicates whether a security check should be performed.
Setting this value to ON(3) will activate the security mechanism
if and only if, the value of prtRRSecurityState is ACTIVE.

Enumerationr/w

.1.3.6.1.4.1.164.1.2.4.1.1.4

prtRRSecurityMask

Mask of the allowed MAC address that can be connected through
this port. The security of the individual port overwrites the
security of the segment where the port belongs to

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.1.2.4.1.1.5

prtRRSecurityPattern

A six-octet(48 bit) pattern, where the masked bits of prtRRSecurityMask
should match the MAC address.

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.1.2.4.1.1.6

prtRRJitterAttenEnable

The value of this attribute determines activation of the
jitters Attenuation mechanism of repeater's port .

Enumerationr/w

Constraints:
range: 1-65535

.1.3.6.1.4.1.164.1.2.4.1.1.7

prtRRConfigMsg

Full configuration message coded in internal RAD application format.
This entry describes port' configuration.

OctetString

Constraints:
range: 1-65535

.1.3.6.1.4.1.164.1.2.4.1.1.8

prtRRFlipAutoDisable

Attribute describing the control on the flipping mechanism of a lobe .
Value ON indicates the ability of the lobe to auto disable itself when flipping occur.
Value OFF indicates that the auto disable mechanism s…

Enumerationr/w

Constraints:
range: 1-65535

.1.3.6.1.4.1.164.1.2.4.1.1.9

prtRRSecurityMask2

Mask of the allowed MAC address that can be connected through
this port. The security of the individual port overwrites the
security of the segment where the port belongs to

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.1.2.4.1.1.10

prtRRSecurityPattern2

A six-octet(48 bit) pattern: where the masked bits of prtRRSecurityMask2
should match the MAC address.

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.1.2.4.1.1.11

prtRRMode

Indicates the port status of rr-sat card after the communication
is broken. When configured to smart-port, the port disables itself
when there is no management communication with attachment.
interRptrPort - this port is…

Enumerationr/w

.1.3.6.1.4.1.164.1.2.4.1.1.12

prtRRAttachment

Indicates the type of the port attachment. Smart attachment types
are applicable for rr-sat card only

Enumeration

.1.3.6.1.4.1.164.1.2.4.1.1.13

prtMMTable

table

.1.3.6.1.4.1.164.1.2.4.2 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtMMTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtMMTable'

RADRing specific WAN modules port information.

prtMMEntry row .1.3.6.1.4.1.164.1.2.4.2.1

An entry in table prtMMTable.

Indexes

No indexes recorded

Column Syntax OID

prtMMmdlID

A unique identifier of the module(slot no.)this port is attached to.

SNMPv2-SMIInteger32

Constraints:
range: 6-6

.1.3.6.1.4.1.164.1.2.4.2.1.1

prtMMID

A unique identifier of the port (link) within its module.

SNMPv2-SMIInteger32

Enumerated Values:

1	ringUp
2	ringDown

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.1.2.4.2.1.2

prtMMAdminCmd

Setting the object to locLoop(2) or remLoop(3) will activate the corresponding test.
Value remLoop(3) activates the BERT test on the related link if mdlMMBertCmd
is set to on(3). Setting parameter to normal(1), restores…

Enumerationr/w

.1.3.6.1.4.1.164.1.2.4.2.1.3

prtMMOperStatus

Reflects the Synchronization status.

Enumeration

.1.3.6.1.4.1.164.1.2.4.2.1.4

prtMMTestStatus

Reflects the link status. When the object is set to the value of bert(4),
it means that the remote loopback is active too.

Enumeration

.1.3.6.1.4.1.164.1.2.4.2.1.5

prtMMBertResult

The value of this object indicates the status of the last BERT test.

Enumeration

.1.3.6.1.4.1.164.1.2.4.2.1.6

prtMMTrapMaskEnable

When this object is set to OFF by the management console, the
agent starts sending the unmasked traps related to this module.
Otherwise, no traps are sent by this module.

Enumerationr/w

.1.3.6.1.4.1.164.1.2.4.2.1.7

prtETTable

table

.1.3.6.1.4.1.164.1.2.4.3 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtETTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtETTable'

RADRing specific Ethernet port information

prtETEntry row .1.3.6.1.4.1.164.1.2.4.3.1

An entry in table prtETTable.

Indexes

No indexes recorded

Column Syntax OID

prtETmdlID

A unique identifier of the module, (slot no.), this port is attached to.

SNMPv2-SMIInteger32

Enumerated Values:

1	ok
2	faulty

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.1.2.4.3.1.1

prtETID

A unique identifier of the port within its module.

SNMPv2-SMIInteger32

Enumerated Values:

1	ok
2	cardConfigErrorAB
3	cardConfigErrorS
4	switchTopologyError

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.1.2.4.3.1.2

prtETTrapMaskEnable

When this attribute is set to OFF by the management console, the
agent starts sending the unmasked traps related to this port.
Otherwise, no traps are sent by this port.

Enumerationr/w

Enumerated Values:

1	on
2	off

.1.3.6.1.4.1.164.1.2.4.3.1.3

prtRRSecTable

table

.1.3.6.1.4.1.164.1.2.4.4 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtRRSecTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtRRSecTable'

RR Port Security Table (10.08.95)

prtRRSecEntry row .1.3.6.1.4.1.164.1.2.4.4.1

An entry in table prtRRSecTable.

Indexes

No indexes recorded

Column Syntax OID

prtRRSecmdlID

A unique identifier of the module,(slot no.),this port is
attached to.

SNMPv2-SMIInteger32

Enumerated Values:

1	on
2	off

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.1.2.4.4.1.1

prtRRSecPrtID

A unique identifier of the port within its module.

SNMPv2-SMIInteger32

Enumerated Values:

1	not-present
2	inserted
3	not-inserted
4	present

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.1.2.4.4.1.2

prtRRSecID

A unique identifier of the security number within the port.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.1.2.4.4.1.3

prtRRSecMask

Mask of the allowed MAC address that can be connected through
this port. The security of the individual port overwrites the
security of the segment, the port belongs to

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.1.2.4.4.1.4

prtRRSecPattern

A six-octet(48 bit) pattern, where the masked bits of
prtRRSecMask should match the MAC address.

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.1.2.4.4.1.5

radFddiStationTable

table

.1.3.6.1.4.1.164.2.1.2 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radFddiStationTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radFddiStationTable'

A list of FddiStation entries. The number of entries is 
given by the value of radFddiStationsNumber.

radFddiStationEntry row .1.3.6.1.4.1.164.2.1.2.1

An entry in table radFddiStationTable.

Indexes

No indexes recorded

Column Syntax OID

radFddiStationIndex

A unique value for each Station. Its value ranges
between 1 and the value ofradFddiStationNumber.

Integer32

.1.3.6.1.4.1.164.2.1.2.1.1

radFddiStationType

Indicates the type of the station.

Enumeration

.1.3.6.1.4.1.164.2.1.2.1.2

radFddiStationBus1TestResult

Indicates the result of a test performed on Bus1.

Enumeration

Enumerated Values:

1	isolated
2	local
3	secondary
4	primary
5	concatenated
6	thru

.1.3.6.1.4.1.164.2.1.2.1.3

radFddiStationBus2TestResult

Indicates the result of a test performed on Bus2.

Enumeration

Enumerated Values:

1	ok
2	lerAlarm
3	lerCutoff

.1.3.6.1.4.1.164.2.1.2.1.4

radFddiStationTempDeInsertAction

This action provides temporary deinsertion of the root
station from the ring. Expressed in milliseconds.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.2.1.2.1.5

radFddiStationPerformTest

A value ON of this attribute indicates that a test should be
performed upon the Station.

Enumerationr/w

.1.3.6.1.4.1.164.2.1.2.1.6

radFddiStationOpticalSwitchStatus

A value ON of this attribute indicates that the Station
is in bypass mode.

Enumeration

.1.3.6.1.4.1.164.2.1.2.1.7

radFddiSMTTable

table

.1.3.6.1.4.1.164.2.2 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radFddiSMTTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radFddiSMTTable'

A list of FddiSMT entries. The number of entries is 
given by the value of snmpFddiSMTNumber.

radFddiSMTEntry row .1.3.6.1.4.1.164.2.2.1

An entry in table radFddiSMTTable.

Indexes

No indexes recorded

Column Syntax OID

radFddiSMTIndex

A unique value for each SMT. Its value ranges
between 1 and the value of snmpFddiSMTNumber.

Integer32

Enumerated Values:

3	event
4	minor
5	major
6	warning
7	critical

.1.3.6.1.4.1.164.2.2.1.1

radFddiSMTStation

Indicates the Station inside the box to which the
current SMT belongs. Its value ranges
between 1 and the value of radFddiStationNumber.

Integer32

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.2.2.1.2

radFddiSMTCFStateobsolete

The attachement configuration for the Station. Extends the
range of values provided by the SNMP variable snmpFddiSMTCFState
from the SNMP FDDI MIB.

Enumeration

.1.3.6.1.4.1.164.2.2.1.3

radFddiSMTLeftSlot

Indicates the slot number of the leftmost card on the concentrator
implemented inside the box and managed by the agent MAC.

SNMPv2-SMIInteger32

Enumerated Values:

2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.2.2.1.4

radFddiSMTRightSlot

Indicates the slot number of the rightmost card on the concentrator
implemented inside the box and managed by the agent MAC. Note that
the MAC-agent card itself is not taken into consideration.

SNMPv2-SMIInteger32

Enumerated Values:

2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.2.2.1.5

radFddiMACTable

table

.1.3.6.1.4.1.164.2.3 · 1 row entry · 13 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radFddiMACTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radFddiMACTable'

A list of FddiMAC entries. The number of entries is 
given by the value of snmpFddiMACNumber.

radFddiMACEntry row .1.3.6.1.4.1.164.2.3.1

An entry in table radFddiMACTable.

Indexes

agnSErrIdx

Column Syntax OID

radFddiMACSMTIndex

The value of the SMT index associated with this MAC.

Integer32

.1.3.6.1.4.1.164.2.3.1.1

radFddiMACIndex

A unique value for each MAC. Its value ranges
between 1 and the value of snmpFddiMACNumber.

Integer32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.2.3.1.2

radFddiMACStation

Indicates the Station inside the box to which the
current MAC belongs. Its value ranges
between 1 and the value of radFddiStationNumber.

Integer32

.1.3.6.1.4.1.164.2.3.1.3

radFddiMACTestResult

Indicates the result of a test performed on MAC.
The value is a sum. It takes the value 0 if the result of the
test is OK and if faults occur, 2 raised to a power is added
to the sum. The powers are according to the fo…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.2.3.1.4

radFddiMACTokenCt

Token Counts - Refer to ANSI MAC {73}.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.2.3.1.5

radFddiMACRingLoad

Current traffic value. The
traffic is expressed in percents of the maximum FDDI traffic
in the range 1..20, expressed on a log(10)
scale ( value = 10*log10(percent) ).

SNMPv2-SMIInteger32

Enumerated Values:

2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.2.3.1.6

radFddiMACRingLoadBuffer

Record of traffic for the last second with a resolution of 100 msec. The
traffic is expressed in percents of the maximum FDDI traffic and each
record contains 10 readings, in the range 1..20, expressed on a log(10)
sca…

OctetString

.1.3.6.1.4.1.164.2.3.1.7

radFddiMACRingLoadTrsh

Traffic threshold value. When exceeded, a trap is send to the management
console. Expressed in percents of the maximum FDDI traffic, in the
range 1..20, expressed on a log(10) scale.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.2.3.1.8

radFddiMACRingLoadPeak

Maximal traffic value since last reset of hub or relay. Expressed in per-
cents of the maximum FDDI traffic, in the range 1..20,
expressed on log(10) scale.

SNMPv2-SMIInteger32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.2.3.1.9

radFddiMACDownstreamNbr

The MAC's downstream neighbor's long individual MAC address. The value
shall be reported as '00 00 00 00 00 00' if it is unknown.

OctetString

Constraints:
range: 1-2

.1.3.6.1.4.1.164.2.3.1.10

radFddiMACRingStatus

Attribute which summs the status of the ring controlled by the current
MAC.

Enumeration

Enumerated Values:

1	internal
2	rxClk
3	adaptive

.1.3.6.1.4.1.164.2.3.1.11

radFddiMACRingUtilization

Current traffic value. The traffic is expressed in percents of the maximum FDDI traffic.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.2.3.1.12

radFddiMACRingPeakUtilization

Peak traffic value since las reset of the hub or relay. The traffic is expressed
in percents of the maximum FDDI traffic.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.2.3.1.13

radFddiGroupTable

table

.1.3.6.1.4.1.164.2.4 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radFddiGroupTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radFddiGroupTable'

A list of FddiGroup entries. The number of entries is 
given by the value of snmpFddiGroupNumber.

radFddiGroupEntry row .1.3.6.1.4.1.164.2.4.1

An entry in table radFddiGroupTable.

Indexes

agnCnfgIdx

Column Syntax OID

radFddiGroupId

Unique ID of the group in radFddiGroupTable. Equivalent to slot number
in enclosures.

SNMPv2-SMIInteger32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.2.4.1.1

radFddiGroupRedundancy

This attribute shows the usage of the A/B pair of ports in Tree mode.
If the redundancy conditions are not fulfilled, value none(1) will be
returned.
If backup mode port A is a standby backup of port B, otherwise each o…

Enumerationr/w

Constraints:
range: 0-30

.1.3.6.1.4.1.164.2.4.1.2

radFddiGroupTopologyMode

Defines the topology mode of the FDDI PHY card.

Enumeration

Constraints:
range: 0-255

.1.3.6.1.4.1.164.2.4.1.3

radFddiGroupTestResult

Result of test performed upon an FDDI group. A value of faulty (1)
indicates a CPU or communication at module level.

Enumeration

Constraints:
range: 0-255

.1.3.6.1.4.1.164.2.4.1.4

radFddiGroupConfigStatus

Indicates the configuration status of the module (group).

Enumeration

.1.3.6.1.4.1.164.2.4.1.5

radFddiGroupAutoRightLoop

Value ON of this attribute signifies that a hardware loop was
automatically created on a FDDI module which does not sense
the existence of another FDDI group on the right hand side.

Enumeration

.1.3.6.1.4.1.164.2.4.1.6

radFddiGroupAutoLeftLoop

Value ON of this attribute signifies that a hardware loop was
automatically created on a FDDI module which does not sense
the existence of another FDDI group on the left hand side.

Enumeration

.1.3.6.1.4.1.164.2.4.1.7

radFddiGroupManRightLoop

Setting this attribute to ON signifies a command to the hardware
to create a loop on the FDDI module which isolates the ring
from the right hand side.

Enumerationr/w

.1.3.6.1.4.1.164.2.4.1.8

radFddiGroupManLeftLoop

Setting this attribute to ON signifies a command to the hardware
to create a loop on the FDDI module which isolates the ring
from the left hand side.

Enumerationr/w

Enumerated Values:

1	psA
2	psB
3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
17	io13
18	io14
19	io15
200	all
255	notApplicable

.1.3.6.1.4.1.164.2.4.1.9

radFddiGroupOpticalSwitchStatus

This attribute describes the presence of the optical switch
and for existing optical switches describes the possibility of
auto-reconfiguration of path resources (MACs and
M-ports) in the case of bus fault or connectio…

Enumeration

.1.3.6.1.4.1.164.2.4.1.10

radFddiPortTable

table

.1.3.6.1.4.1.164.2.5 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radFddiPortTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radFddiPortTable'

radFddiPortEntry row .1.3.6.1.4.1.164.2.5.1

An entry in table radFddiPortTable.

Indexes

No indexes recorded

Column Syntax OID

radFddiPortGroupID

ID of group to which the FDDI card belongs.

SNMPv2-SMIInteger32

Enumerated Values:

2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.2.5.1.1

radFddiPortID

Unique Id of the port in the radFddiPortEntry.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.2.5.1.2

radFddiPortTestResult

Indicates the result of a test performed on a port.

Enumeration

.1.3.6.1.4.1.164.2.5.1.4

radFddiPortNumberOfConnectedStations

Number of stations connected to the port.

SNMPv2-SMIInteger32

Enumerated Values:

3	event
4	minor
5	major
6	warning
7	critical

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.2.5.1.5

radFddiPortConnectedStations

This attribute displays the configuration of the stations connected
to the port.The FDDI addresses of the stations are displayed in ring
order, starting with the address of the first station connected to the
port. The…

OctetString

.1.3.6.1.4.1.164.2.5.1.6

radFddiPortCurrentPathobsolete

Current Path in FDDI port on PHY cards.

Enumerationr/w

.1.3.6.1.4.1.164.2.5.1.8

radFddiPortFunctionalStatus

Fubctional status of the port according to value of link error
estimate relative to thresholds of alarm and cutoff.

Enumerationr/w

Enumerated Values:

1	trap
2	buffer
3	relay
4	alrLedOn
5	alrLedBlink
6	relay2

.1.3.6.1.4.1.164.2.5.1.9

agnSAlrTable

table

.1.3.6.1.4.1.164.3.1.2.1.15 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnSAlrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnSAlrTable'

List of agent related alarms and indications for alarms at
system level.

agnSAlrEntry row .1.3.6.1.4.1.164.3.1.2.1.15.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

agnSAlrIdx

A unique number to identify an entry in the alarm status table
of the agent.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.1.15.1.1

agnSAlrCodeDescription

This attribute is a full text description of the alarm .
The alarm description includes the following information:
alarm code, alarm text, alarm severity, Masked or Inverted
flag and counter.

OctetString

.1.3.6.1.4.1.164.3.1.2.1.15.1.2

agnSAlrCode

A code identifying the alarm of an entry in the alarm status
table at system level.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.1.15.1.3

agnSAlrSeverity

The severity of the alarm.

Enumeration

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.1.2.1.15.1.4

agnSAlrState

State of the alarm.

Enumeration

.1.3.6.1.4.1.164.3.1.2.1.15.1.5

agnSAlrCounter

A counter - how many times the alarm occured since last
clear operation.
ON and OFF Alarm will be counted separately.

SNMPv2-SMIInteger32

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.1.15.1.6

agnSAlrMask

Alarm mask : on/off.

Enumeration

.1.3.6.1.4.1.164.3.1.2.1.15.1.7

agnSAlrInvert

Alarm invert : on/off.

Enumeration

.1.3.6.1.4.1.164.3.1.2.1.15.1.8

agnSErrListTable

table

.1.3.6.1.4.1.164.3.1.2.1.20 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnSErrListTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnSErrListTable'

List of errors and warnings found during Sanity Check
process.

agnSErrListEntry row .1.3.6.1.4.1.164.3.1.2.1.20.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

agnSErrIdx

Unique number to identify an entry in the error list table.
The maximum entry value cannot exceed the value of
'agnSNoOfSanityCheckErr'.

SNMPv2-SMIInteger32

Enumerated Values:

2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.1.20.1.1

agnSErrDescription

This attribute is a full text description of the sanity check
error including error code, slot and port numbers related to
the code .

OctetString

.1.3.6.1.4.1.164.3.1.2.1.20.1.2

agnSCnfgTable

table

.1.3.6.1.4.1.164.3.1.2.1.22 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnSCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnSCnfgTable'

This table contains an entry per configuration. It indicates
if the configuration is valid.

agnSCnfgEntry row .1.3.6.1.4.1.164.3.1.2.1.22.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

agnSEntryIdx

Unique number to identify an entry in the configuration table.

SNMPv2-SMIInteger32

Enumerated Values:

2	primary
3	secondary
4	third
5	fourth

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.1.22.1.1

agnSEntryIsValid

This attribute indicates whether the specific configuration
is valid in the MUX . Value of NO indicates: no such
configuration in the MUX.

Enumeration

Enumerated Values:

2	none
3	e1T1a
4	e1T1b
5	eth
6	ethNetUser

.1.3.6.1.4.1.164.3.1.2.1.22.1.2

agnCClkSrcTable

table

.1.3.6.1.4.1.164.3.1.2.2.4 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnCClkSrcTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnCClkSrcTable'

All the entries of this table are identical (have the same
value) for all the configurations (1..100) except the
TmpCnfg.
The write operation into the Table Objects is valid only
for the TmpCnfg entry.

agnCClkSrcEntry row .1.3.6.1.4.1.164.3.1.2.2.4.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
agnCClkCnfgIdx This attribute indicates the Idx of the Cnfg(1..100) being accessed and Idx 255 relates to the TmpCnfg.	Integer32	`.1.3.6.1.4.1.164.3.1.2.2.4.1.1`
agnCClkSrcIdx An index to the table. There are only two entries to this table. Index 1 points to the Master clock parameters and Index 2 points to the Fallback clock parameters	Integer32	`.1.3.6.1.4.1.164.3.1.2.2.4.1.2`
agnCClkSrcMode The source of the nodal timing.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.2.2.4.1.3`
agnCClkSrcSlt This entry is valid only when we are working in rxClk mode. For an invalid entry, the return value will be '7fff'h.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.2.2.4.1.4`
agnCClkSrcPrt This entry is valid only when we are working in rxClk or adaptive mode. For an invalid entry, the return value will be '7fff'h. - For rxClk mode, the values can be: exPrt1 (1) , exPrt2 (2) , …	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.2.2.4.1.5`

agnCnfgDataTable

table

.1.3.6.1.4.1.164.3.1.2.2.7 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnCnfgDataTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnCnfgDataTable'

This table contains data about the agent configurations.
The table will support only data about valid configurations
of the agent.

agnCnfgDataEntry row .1.3.6.1.4.1.164.3.1.2.2.7.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
agnCnfgIdx This object indicates the Idx of the agent' Cnfg the following objects refer. 255=Temporary Cnfg (Set is done only to this configuration).	Integer32	`.1.3.6.1.4.1.164.3.1.2.2.7.1.1`
agnCnfgDesc This object is a description of the Configuration, entered by user, to enhance Cnfg recognition.	OctetStringr/w	`.1.3.6.1.4.1.164.3.1.2.2.7.1.2`
agnCnfgUpdDate This object indicates the date when last update of this configuration was performed, as it is known by the agent using its own real-time clock. The format would be as specified by the agnSDateFormat. When update is perf…	OctetString	`.1.3.6.1.4.1.164.3.1.2.2.7.1.3`
agnCnfgUpdTime This object indicates the time when last update of this configuration was performed, as it is known by the agent using its own real-time clock. When update is performed, the agent should save the time.	OctetString	`.1.3.6.1.4.1.164.3.1.2.2.7.1.4`
agnCnfgUpdMnger This object indicates the IP Address of the Manager who performed the last update of this configuration. When update is performed, the agent should save the IP Address of the Manager who commanded the update. That will …	RFC1155-SMIIpAddress Type Constraints: `range: 4`	`.1.3.6.1.4.1.164.3.1.2.2.7.1.5`

agnCnfgAlrTable

table

.1.3.6.1.4.1.164.3.1.2.2.8.2 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnCnfgAlrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnCnfgAlrTable'

This table enables the user to set attributes to each alarm.
Setting  for a non-existing entry agnCnfgAlrMask,
agnCnfgAlrInvert or agnCnfgAlrFilter to 'yes'(or yesAndSave
for Mask) will add this new entry to the table.
Setting  for an existing entry agnCnfgAlrMask/
agnCnfgAlrInvert/agnCnfgAlrFilter (one or more) to 'no'
(noAndSave for Mask)  so that ALL  these objects' values are
'no' , will delete this entry from the table.
For agnCnfgAlrMask, only if [(last saved value=noAndSave)
AND (new value is 'no' or 'noAndSave')] the object's value
is considered 'no' for deleting the entry.
          
For some products (like MP, MPH, Vmux2100) the Active Alarms are always
part of the table and cannot be removed even if their Mask/Invert/Filter
are No.

agnCnfgAlrEntry row .1.3.6.1.4.1.164.3.1.2.2.8.2.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
agnCnfgAlrCode The alarm code. The following attributes refer this code.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.2.2.8.2.1.1`
agnCnfgAlrSlot The alarm slot. The following attributes apply for the alarm code and slot selected. all = the attributes apply to all slots. notApplicable = the selected alarm is for system level. For the Vmux2100 Main Board clA (3) …	Enumeration	`.1.3.6.1.4.1.164.3.1.2.2.8.2.1.2`
agnCnfgAlrPort The alarm port. The following attributes apply for the alarm code,slot and port selected. 200 = all = the attributes apply to all ports of the selected slot. When selected Slot is 'all', only 'all' or 'notApplicab…	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.2.2.8.2.1.3`
agnCnfgAlrMask An attribute defining the desired Mask state of an alarm . no - unmask (this command is not saved in agent's common database) noAndSave - unmask ; this command is saved in agent's common database yes - mask …	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.2.2.8.2.1.4`
agnCnfgAlrInvert An attribute defining the desired Invert state of an alarm . no - not inverted. yes - inverted. For MP, it is not applicable for alarms that are currently OFF.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.2.2.8.2.1.5`
agnCnfgAlrFilter An attribute defining if Filter is desired for the alarm . no - no filter. yes - filter activate. This filter is activated within a window of time defined by agnCnfgAlrFilterWindow. Its purpose is to av…	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.2.2.8.2.1.6`
agnCnfgAlrFilterSet This is a top threshold causing the alarm that passes it, to be declared Set (ON) at the end of the respective window of time. - For alarms defined by default as state alarms (minor,major) this value will be in [%]. -…	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.2.2.8.2.1.7`
agnCnfgAlrFilterReset This is a bottom threshold causing the alarm that does not pass it, to be declared Reset (ON) at the end of the respective window of time. - For alarms defined by default as state alarms (minor,major) this value will …	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.2.2.8.2.1.8`
agnCnfgAlrSeverity An attribute defining desired severity of an alarm code per slot/port	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.2.2.8.2.1.9`

agnCnfgAlrReportTable

table

.1.3.6.1.4.1.164.3.1.2.2.8.3 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnCnfgAlrReportTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnCnfgAlrReportTable'

This table enables the user to configure the desired Alarm
Reports according to alarms severity.

agnCnfgAlrReportEntry row .1.3.6.1.4.1.164.3.1.2.2.8.3.1

An entry in table.

Indexes

agnAlarmsCmprVersion agnAlarmsCmprAlarmIdx

Column	Syntax	OID
agnCnfgAlrReportType The alarm report type. trap - traps will be sent only for alarms having the selected On/Off severity or higher. buffer - only alarms having the selected On/Off severity and higher, will be reported to th…	Enumeration	`.1.3.6.1.4.1.164.3.1.2.2.8.3.1.1`
agnCnfgAlrStartReportOn This object specifies the severity from which alarms will be reported. Alarms having this severity or higher, will be reported. This object specifies the report severity only for alarms that turn to ON state. noReport …	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.2.2.8.3.1.2`
agnCnfgAlrStartReportOff This object specifies the severity from which alarms will be reported. Alarms having this severity or higher, will be reported. This object specifies the report severity only for alarms that turn to OFF state. notAppl…	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.2.2.8.3.1.3`

agnCT1E1RingTable

table

.1.3.6.1.4.1.164.3.1.2.2.10 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnCT1E1RingTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnCT1E1RingTable'

Configuration of all T1/E1 Ring ML cards and ports.
The write operation into the table objects is valid only
for the TmpCnfg.
A Slot/Port that does not participate in the T1/E1 Ring, 
will not exist in this table.
A ML port that exists in this table, cannot exist at the same
time in the IO Redundancy table (sysCRdnTable).

agnCT1E1RingEntry row .1.3.6.1.4.1.164.3.1.2.2.10.1

An Entry in table agnCT1E1RingTable

Indexes

agnAlrBufCmprVersion agnAlrBufCmprAlarmIdx

Column Syntax OID

agnCT1E1RingCnfgIdx

This object indicates the Idx of the Cnfg(1..255) being
accessed ; Idx of 255 relates to the TmpCnfg.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.2.10.1.1

agnCT1E1RingPrimeSlot

The slot number of the Primary card of the Ring Pair.

Enumeration

.1.3.6.1.4.1.164.3.1.2.2.10.1.2

agnCT1E1RingPrimePort

The port number in the Primary Card.
For external ports, the value will be as that of the port in the
card. Example: external-3 -> 3
external-4 -> 4
For internal ports, the value will be 100 + the port…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.2.10.1.3

agnCT1E1RingSecSlot

The slot number of the Secondary card of the Ring Pair.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.2.2.10.1.4

agnCT1E1RingSecPort

The port number in the Secondary Card.
For external ports, the value will be as that of the port in the
card. Example: external-3 -> 3
external-4 -> 4
For internal ports, the value will be 100 + the po…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.2.10.1.5

agnCT1E1RingRecTime

T1/E1 Ring Recovery Time (sec).
Valid Values: 1..99, 65535.
65535=NA.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.2.10.1.6

agnCT1E1RingRowStatus

This parameter allows NMS to create/delete entries of this table.
The only possible supported RowStatus vaules are
active (1) and destroy (6).

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …

.1.3.6.1.4.1.164.3.1.2.2.10.1.7

agnCT1E1RingWTR

T1/E1 Ring Wait to Restore (sec).
Valid Values: 0..999, 65535.
65535=NA.
When the value <> 65535, the value of agnCT1E1RingRecTime must be 65535.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.2.2.10.1.8

agnCT1E1RingDualFailDetection

T1/E1 Ring - Dual Failure Detection enable/disable.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.2.2.10.1.9

agnCBuMlTable

table

.1.3.6.1.4.1.164.3.1.2.2.12 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnCBuMlTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnCBuMlTable'

Configuration for Primary, Secondary and Third Link.
These are used for Link Backup.

agnCBuMlEntry row .1.3.6.1.4.1.164.3.1.2.2.12.1

An Entry in table agnCBuMlTable

Indexes

No indexes recorded

Column	Syntax	OID
agnCBuMlCnfgIdx This object indicates the Index of the Configuration database (1..255) being accessed. Index of 255 relates to the Temporary Configuration.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.2.2.12.1.1`
agnCBuMlRole The Role of the Link. Primary Link is the Link that should usually work. If the Primary Link fails, the data will go through the Secondary Link. If both Primary and Secondary Links fail, the data will go through the Thi…	Enumeration	`.1.3.6.1.4.1.164.3.1.2.2.12.1.2`
agnCBuMlType The Type of the Link. For E1/T1 the Link can be Link A - e1T1a or Link B - e1T1b. For ETH-NET, eth (5) can be used. For ETH-NET/USER ethNetUser (6) can be used.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.2.2.12.1.3`
agnCBuMlDefaultGateway Default Gateway's IP Address.	RFC1155-SMIIpAddressr/w Type Constraints: `range: 4`	`.1.3.6.1.4.1.164.3.1.2.2.12.1.4`
agnCBuMlSubnetMask The Link subnet mask.	RFC1155-SMIIpAddressr/w Type Constraints: `range: 4`	`.1.3.6.1.4.1.164.3.1.2.2.12.1.5`
agnCBuMlOamFrequency Time in sec. between 2 OAM packets.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.2.2.12.1.6`
agnCBuMlOamTimeoutCycles No. of cycles the Link will send OAM packets without receiving a response from the remote Link before switching to the Backup Link.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.2.2.12.1.7`
agnCBuMlWaitToRestore This object defines traffic recovery time (in milliseconds) of the link after its recovery. This object is applicable only when Recovery Mode is revertive.	SNMPv2-SMIUnsigned32r/w Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.2.2.12.1.8`
agnCBuMlBfdSessionNum This object defines the BFD (Bidirectional Forwarding Detection) session number of the link. When no session exists or when N/A, the value will be 0.	SNMPv2-SMIUnsigned32r/w Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.2.2.12.1.9`

agnCQ50Table

table

.1.3.6.1.4.1.164.3.1.2.2.13 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnCQ50Table

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnCQ50Table'

Table for the device Q50 parameters.
Q50 is a Signaling protocol used between PBX devices.
It is possible to control the initiation of calls using Q.50.
This is useful for devices when there is a congestion.

agnCQ50Entry row .1.3.6.1.4.1.164.3.1.2.2.13.1

An Entry in table agnCQ50Table

Indexes

No indexes recorded

Column	Syntax	OID
agnCQ50CnfgIdx This object indicates the Index of the Configuration database (1..255) being accessed. Index of 255 relates to the Temporary Configuration.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.2.2.13.1.1`
agnCQ50StopCallsThresh This object indicates the Bandwidth Threshold percent (%) above which new Calls from the PBX will be disabled.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.2.2.13.1.2`
agnCQ50DiscardPktThresh This object indicates the Bandwidth Threshold percent (%) above which voice packets will be discarded. Usually, the value selected should be higher than the value of agnCQ50StopCallsThresh.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.2.2.13.1.3`
agnCQ50BlockNewModemVbdCallsThresh This object indicates the Modem VBD Calls Threshold percent (%) above which new modem calls will be rejected.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.2.2.13.1.4`
agnCQ50BlockNewModemRelayCallsThresh This object indicates the Modem Relay Calls Threshold percent (%) above which new modem calls will be rejected.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.2.2.13.1.5`

agnCmprTable

table

.1.3.6.1.4.1.164.3.1.2.3.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnCmprTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnCmprTable'

A table.

agnCmprEntry row .1.3.6.1.4.1.164.3.1.2.3.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

agnCmprTypIdx

This attribute indicates the Type of the Compressed being
referred.

SNMPv2-SMIInteger32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.1.2.3.1.1.1

agnCmprCnfgIdx

This attribute indicates the configuration to which the
Compressed information is related.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.3.1.1.2

agnCmprVersion

This attribute indicates the version of the internal format
of the Compressed data

SNMPv2-SMIInteger32

Enumerated Values:

1	psA
2	psB
3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.3.1.1.3

agnCmprObj

This attribute is the compressed information itself.

OctetStringr/w

.1.3.6.1.4.1.164.3.1.2.3.1.1.4

agnDlciCmprTable

table

.1.3.6.1.4.1.164.3.1.2.3.2 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnDlciCmprTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnDlciCmprTable'

A table.

agnDlciCmprEntry row .1.3.6.1.4.1.164.3.1.2.3.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

agnDlciCmprCnfgIdx

This attribute indicates the configuration to which the
Compressed information is related.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.3.2.1.1

agnDlciCmprVersion

This attribute indicates the version of the internal format
of the Compressed data

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.3.2.1.2

agnDlciCmprDlciIdx

This attribute indicates a unique identifier of the Dlci,
the compressed information relates to.
The values are between 16 - 991.

SNMPv2-SMIInteger32

Enumerated Values:

1	active
255	temporary

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.3.2.1.3

agnDlciCmprObj

This attribute is the compressed information itself.

OctetStringr/w

Enumerated Values:

1	sunday
2	monday
3	tuesday
4	wednesday
5	thursday
6	friday
7	saturday

.1.3.6.1.4.1.164.3.1.2.3.2.1.4

agnAlarmsCmprTable

table

.1.3.6.1.4.1.164.3.1.2.3.3 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnAlarmsCmprTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnAlarmsCmprTable'

A table.

agnAlarmsCmprEntry row .1.3.6.1.4.1.164.3.1.2.3.3.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

agnAlarmsCmprVersion

This attribute indicates the version of the internal
format of the Compressed data

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.3.3.1.1

agnAlarmsCmprAlarmIdx

A unique number to identify an entry in the alarm status table
of the agent.

SNMPv2-SMIInteger32

Enumerated Values:

1	active
255	temporary

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.3.3.1.2

agnAlarmsCmprObj

This attribute is the compressed information itself.

OctetString

Constraints:
range: 1-10

.1.3.6.1.4.1.164.3.1.2.3.3.1.3

agnAlrBufCmprTable

table

.1.3.6.1.4.1.164.3.1.2.3.4 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnAlrBufCmprTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnAlrBufCmprTable'

A table.

agnAlrBufCmprEntry row .1.3.6.1.4.1.164.3.1.2.3.4.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

agnAlrBufCmprVersion

This attribute indicates the version of the internal format of
the Compressed data

SNMPv2-SMIInteger32

Constraints:
range: 1-512

.1.3.6.1.4.1.164.3.1.2.3.4.1.1

agnAlrBufCmprAlarmIdx

A unique number to identify an entry in the history alarms
buffer of the agent.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.3.4.1.2

agnAlrBufCmprObj

This attribute is the compressed information itself.

OctetString

.1.3.6.1.4.1.164.3.1.2.3.4.1.3

agnSCmprErrListTable

table

.1.3.6.1.4.1.164.3.1.2.3.5 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnSCmprErrListTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnSCmprErrListTable'

A table.

agnSCmprErrListEntry row .1.3.6.1.4.1.164.3.1.2.3.5.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

agnSCmprErrVersion

The version of the compressed data

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	fullWorkday
3	partialWorkday
4	weekend

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.3.5.1.1

agnSCmprErrIdx

Unique number to identify an entry in the errors list table.
The maximum entry value cannot exceed the value of
'agnSNoOfSanityCheckErr'.

SNMPv2-SMIInteger32

Constraints:
range: 5-5

.1.3.6.1.4.1.164.3.1.2.3.5.1.2

agnSCmprErrObj

This attribute is a full text description of the error,
including: error code, slot and port numbers related to the
code .

OctetString

Constraints:
range: 5-5

.1.3.6.1.4.1.164.3.1.2.3.5.1.3

agnTsCmprTable

table

.1.3.6.1.4.1.164.3.1.2.3.6 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnTsCmprTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnTsCmprTable'

A table.

agnTsCmprEntry row .1.3.6.1.4.1.164.3.1.2.3.6.1

An entry in table.

Indexes

agnCFlipCnfgIdx agnCFlipIdx

Column Syntax OID

agnTsCmprVerIdx

This object indicates the version of the internal format
of the Compressed data.

SNMPv2-SMIInteger32

Enumerated Values:

1	active
255	temporary

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.3.6.1.1

agnTsCmprCnfgIdx

This object indicates the configuration to which the
Compressed information is related.
255=temporary configuration.
Set can be performed only to the temporary configuration.

SNMPv2-SMIInteger32

Constraints:
range: 1-10

.1.3.6.1.4.1.164.3.1.2.3.6.1.2

agnTsCmprSlotIdx

This object indicates the Slot to which the
Compressed information is related.
For MP-2100: IO-1..IO-12 = (5).. (16)
For DXC-30 : IO-1..IO-15 = (5).. (19).
NA=255.

SNMPv2-SMIInteger32

Enumerated Values:

2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.3.6.1.3

agnTsCmprPortIdx

This object indicates the Port within the Slot, to which the
Compressed information is related.
For Port Index see each product's spec.

SNMPv2-SMIInteger32

Constraints:
range: 1-20

.1.3.6.1.4.1.164.3.1.2.3.6.1.4

agnTsCmprPduIdx

This object indicates the PDU index within the same port.
That provides for the case when one PDU is not sufficient for all TS
Assignment data of the same port.

SNMPv2-SMIInteger32

Constraints:
range: 1-10

.1.3.6.1.4.1.164.3.1.2.3.6.1.5

agnTsCmprData

This object is the compressed information itself. It provides
information about all TSs of a port.

OctetStringr/w

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.1.2.3.6.1.6

agnXCmprTable

table

.1.3.6.1.4.1.164.3.1.2.3.7 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnXCmprTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnXCmprTable'

A table.

agnXCmprEntry row .1.3.6.1.4.1.164.3.1.2.3.7.1

An entry in table.

Indexes

agnListDecodingType agnListDecodingCode

Column Syntax OID

agnXCmprTypIdx

This attribute indicates the Type of the Compressed being
referred.
One of the types is V5.1 Variant data.

SNMPv2-SMIInteger32

Enumerated Values:

1	alr
2	sanity
3	counter

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.3.7.1.1

agnXCmprVersion

This attribute indicates the version of the internal format of
the Compressed data.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.3.7.1.2

agnXCmprIdx3

3rd index - can be used for any purpose according to the
agnXCmprTypIdx.
Example: for V5.1 Variant, this attribute indicates the configuration
to which the Compressed information is related.
255=temporary configuratio…

SNMPv2-SMIInteger32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.1.2.3.7.1.3

agnXCmprIdx4

4th index - can be used for any purpose according to the
agnXCmprTypIdx.
Example: for V5.1 Variant,this attribute indicates a unique number of
the slot position where the card is inserted.
Valid values: psA(1),psB…

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
3	event
4	minor
5	major
6	warning
7	critical

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.3.7.1.4

agnXCmprIdx5

5th index - can be used for any purpose according to the
agnXCmprTypIdx.
Example: for V5.1 Variant,this attribute indicates a unique identifier
of the port the compressed information relates to.
Valid values: exPrt1 …

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
3	event
4	minor
5	major
6	warning
7	critical

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.3.7.1.5

agnXCmprIdx6

6th index - can be used for any purpose according to the
agnXCmprTypIdx.
Example: for V5.1 Variant,this attribute indicates the Variant index.
Valid values are: 0..127, 255 (= temp cnfg).Set can be performed only
to …

SNMPv2-SMIInteger32

Enumerated Values:

1	none
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.3.7.1.6

agnXCmprIdx7

7th index - can be used for any purpose according to the
agnXCmprTypIdx.
Example: for V5.1 Variant,this attribute is not needed. Therefore, its
value will be always 255=notApplicable.

SNMPv2-SMIInteger32

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.3.7.1.7

agnXCmprObj

This attribute is the compressed information itself.

OctetStringr/w

.1.3.6.1.4.1.164.3.1.2.3.7.1.8

alrBufTable

table

.1.3.6.1.4.1.164.3.1.2.4.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk alrBufTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::alrBufTable'

A table.

alrBufEntry row .1.3.6.1.4.1.164.3.1.2.4.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

alrBufIdx

This attribute indicates a unique number to identify this
entry

SNMPv2-SMIInteger32

Enumerated Values:

3	cl
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
254	vs
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.4.1.1.1

alrBufDescription

This entry is a unique text description of the alarm in the
buffer.
The alarm description includes the following information:
alarm code, slot id, card type, channel id ,
alarm text, alarm status, masked flag and event …

OctetString

.1.3.6.1.4.1.164.3.1.2.4.1.1.2

alrBufCode

A code identifying the alarm of an entry in the alarm buffer
table.

SNMPv2-SMIUnsigned32

Constraints:
range: 0-991

.1.3.6.1.4.1.164.3.1.2.4.1.1.3

alrBufSlot

The slot number this alarm refers to.
When the alarm refers to a system alarm, the value will be 'notApplicable(255)'.

Enumeration

Enumerated Values:

3	cl
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.1.2.4.1.1.4

alrBufPort

The port number this alarm refers to.
If the port number is irrelevant to this alarm (if it is
a system/card level alarm) the value will be 9999.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.2.4.1.1.5

alrBufSeverity

The severity of the alarm.

Enumeration

Constraints:
range: 1-991

.1.3.6.1.4.1.164.3.1.2.4.1.1.6

alrBufState

State of the alarm (On/Off).

Enumeration

Enumerated Values:

1	full
2	zero
3	txBc5100bps
4	txBc6400bps
5	txBc8300bps
6	txBc9600bps
7	txBc14400bps
8	txBc19200bps
9	txBc28800bps
10	txBc32000bps
11	txBc38400bps
12	txBc48000bps
13	txBc56000bps
14	txBc57600bps
15	txBc64Kbps
16	txBc128Kbps
17	txBc192Kbps
18	txBc256Kbps
19	txBc320Kbps
20	txBc384Kbps
21	txBc448Kbps
22	txBc512Kbps
23	txBc768Kbps
24	txBc896Kbps
25	txBc1024Kbps
26	txBc1152Kbps
27	txBc1280Kbps
28	txBc1344Kbps
29	txBc1472Kbps
30	txBc1600Kbps
31	txBc1728Kbps
32	txBc1856Kbps
33	txBc1920Kbps
34	txBc1984Kbps
35	txBc2048Kbps
36	txBc16000bps
37	txBc112Kbps
38	txBc168Kbps
39	txBc224Kbps
40	txBc336Kbps
41	txBc672Kbps
42	txBc1536Kbps
43	txBc1792Kbps

.1.3.6.1.4.1.164.3.1.2.4.1.1.7

agnCAgendaTable

table

.1.3.6.1.4.1.164.3.1.2.5.1 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnCAgendaTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnCAgendaTable'

This table devides the week days into categories needed for
DB flip consideration.

agnCAgendaEntry row .1.3.6.1.4.1.164.3.1.2.5.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

agnCAgendaCnfgIdx

Active or Temporary Agenda Table.
Both configurations can be read but only the Temporary can
be written to.

Enumeration

Enumerated Values:

1	full
2	zero
3	rxBe5100bps
4	rxBe6400bps
5	rxBe8300bps
6	rxBe9600bps
7	rxBe14400bps
8	rxBe19200bps
9	rxBe28800bps
10	rxBe32000bps
11	rxBe38400bps
12	rxBe48000bps
13	rxBe56000bps
14	rxBe57600bps
15	rxBe64Kbps
16	rxBe128Kbps
17	rxBe192Kbps
18	rxBe256Kbps
19	rxBe320Kbps
20	rxBe384Kbps
21	rxBe448Kbps
22	rxBe512Kbps
23	rxBe768Kbps
24	rxBe896Kbps
25	rxBe1024Kbps
26	rxBe1152Kbps
27	rxBe1280Kbps
28	rxBe1344Kbps
29	rxBe1472Kbps
30	rxBe1600Kbps
31	rxBe1728Kbps
32	rxBe1856Kbps
33	rxBe1920Kbps
34	rxBe1984Kbps
35	rxBe2048Kbps
36	rxBe16000bps
37	rxBe112Kbps
38	rxBe168Kbps
39	rxBe224Kbps
40	rxBe336Kbps
41	rxBe672Kbps
42	rxBe1536Kbps
43	rxBe1792Kbps

.1.3.6.1.4.1.164.3.1.2.5.1.1.1

agnCAgendaDayIdx

Day of week

Enumeration

Constraints:
range: 1-8

.1.3.6.1.4.1.164.3.1.2.5.1.1.2

agnCAgendaDayCategory

The Category of the Day

Enumerationr/w

Enumerated Values:

1	disconnected
2	connected

.1.3.6.1.4.1.164.3.1.2.5.1.1.3

agnCFlipNetEventsTable

table

.1.3.6.1.4.1.164.3.1.2.5.2 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnCFlipNetEventsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnCFlipNetEventsTable'

This table holds the Net Events the MUX should trace

agnCFlipNetEventsEntry row .1.3.6.1.4.1.164.3.1.2.5.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

agnCFlipNetEventsCnfgIdx

Active or Temporary Net Events Table.
Both configurations can be read but only the Temporary can
be written to.

Enumeration

Enumerated Values:

1	notApplicable
2	rip
3	rip2
4	none

.1.3.6.1.4.1.164.3.1.2.5.2.1.1

agnCFlipNetEventIdx

Entry within the table

Integer32

.1.3.6.1.4.1.164.3.1.2.5.2.1.2

agnCFlipNetEventActive

Indicates if the entry is valid.
In order to Add/Modify parameters of an entry, this object
should be set to Yes.
In order to delete an entry, this object should be Set to No.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.2.5.2.1.3

agnCFlipNetEventType

The Net Event type

Enumerationr/w

.1.3.6.1.4.1.164.3.1.2.5.2.1.4

agnCFlipNetEventNo

The Net Event No. (Bit Index)

Integer32r/w

Enumerated Values:

1	active
255	temporary

.1.3.6.1.4.1.164.3.1.2.5.2.1.5

agnCFlipNetEventSlot

The slot to which the net event relates .
Not applicable for time event

Enumerationr/w

Constraints:
range: 1-2

.1.3.6.1.4.1.164.3.1.2.5.2.1.6

agnCFlipNetEventPort

The port within the relevant slot.
Valid values:
- extPrt1(1)..exPrt16(16)
- notApplicable(100)
- inPrt1(101)..inPrt84(184)

SNMPv2-SMIInteger32r/w

Constraints:
range: 1-3

.1.3.6.1.4.1.164.3.1.2.5.2.1.7

agnCFlipNetEventISD

The time in seconds since the Net Event was reported as ON
until it is considered as ON.
Not relevant for time events.

Integer32r/w

Constraints:
range: 0-20

.1.3.6.1.4.1.164.3.1.2.5.2.1.8

agnCFlipNetEventOSD

The time in seconds since the net event was reported as OFF
until it is considered as OFF.
Not relevant for time events.

Integer32r/w

Constraints:
range: 0-30

.1.3.6.1.4.1.164.3.1.2.5.2.1.9

agnCFlipNetEventDayType

The time event relates to all days defined in this category in
the agnCAgendaTable.
Applicable only for time event

Enumerationr/w

Constraints:
range: 0-30

.1.3.6.1.4.1.164.3.1.2.5.2.1.10

agnCFlipNetEventStartTime

The time event will be activated at this time.
The format is hh:mm.

OctetStringr/w

Enumerated Values:

2	staticDialPlan
3	staticDialPlanPlus
4	flexDialPlan

.1.3.6.1.4.1.164.3.1.2.5.2.1.11

agnCFlipNetEventEndTime

The time event will be deactivated at this time.
The format is hh:mm.

OctetStringr/w

.1.3.6.1.4.1.164.3.1.2.5.2.1.12

agnCFlipTable

table

.1.3.6.1.4.1.164.3.1.2.5.3 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnCFlipTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnCFlipTable'

The DB Flip Decisions Table

agnCFlipEntry row .1.3.6.1.4.1.164.3.1.2.5.3.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

agnCFlipCnfgIdx

Active or Temporary Flip Decisions Table.
Both configurations can be read but only the Temporary can
be written to.

Enumeration

.1.3.6.1.4.1.164.3.1.2.5.3.1.1

agnCFlipIdx

Entry number within the table

Integer32

Constraints:
range: 1-7

.1.3.6.1.4.1.164.3.1.2.5.3.1.2

agnCFlipActive

Indicates if the entry is valid.
In order to Add/Modify parameters of an entry this object
should be Set to Yes.
In order to delete an entry, this object should be Set to No.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	zone
3	node
4	shortDialing
5	in
6	hgr
7	del
8	rep
9	pri
10	bri
11	numDigDP
12	route
13	ext

.1.3.6.1.4.1.164.3.1.2.5.3.1.3

agnCFlipLogicalExp

A logical expression composed of events numbers (which were
configured in the 'AgnCFlipNetEvantsTable') and logical operators
('|', '&', '!', '(', ')') between them.
e.g - (1 & !2) | (121 & 230)

OctetStringr/w

Constraints:
range: 1-7

.1.3.6.1.4.1.164.3.1.2.5.3.1.4

agnCFlipDbNo

The ID of the required DB

Integer32r/w

Enumerated Values:

2	noConnect
3	cl
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.1.2.5.3.1.5

agnCFlipDiscardDe

Indicates whether the Mux should start discarding
all DE. (MP3000 Only).

Enumerationr/w

.1.3.6.1.4.1.164.3.1.2.5.3.1.6

agnListDecodingTable

table

.1.3.6.1.4.1.164.3.1.2.7.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnListDecodingTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnListDecodingTable'

A decoding table . For each type of list, a description is
given for each existing code.

agnListDecodingEntry row .1.3.6.1.4.1.164.3.1.2.7.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

agnListDecodingType

The type of list the decoding data refers to.
alr - Alarms list
sanity - Sanity Check Error list.
counter - Counter type of ifPerfCounterType

Enumeration

.1.3.6.1.4.1.164.3.1.2.7.1.1.1

agnListDecodingCode

The specific code for which decoding is needed.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.7.1.1.2

agnListDecodingDescription

The description fitting the specific code and type of list
required.

OctetString

.1.3.6.1.4.1.164.3.1.2.7.1.1.3

agnListDecodingDefState

This object is applicable only for agnListDecodingType=alr.
It reports the default state/severity of each alarm.
User can change the severity of the alarms defined by
this default via the agnListDecodingSeverity object.

Enumeration

.1.3.6.1.4.1.164.3.1.2.7.1.1.4

agnListDecodingSeverity

This object is applicable only for agnListDecodingType=alr.
It enables the user to select a severity for each alarm.
The severity is set per alarm code (same for all slots/ports
using this code).
event - can be set only…

Enumerationr/w

Enumerated Values:

1	active
255	temporary

.1.3.6.1.4.1.164.3.1.2.7.1.1.5

agnListDecodingAcmRelaySlt

This object indicates the ACM slot, desired for outbound relay
(report) for the selected alarm.
In the ?004 Unit the entries io6(10)..io12(16) are not valid.
none - when agnListDecodingType=alr AND the selected
…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.2.7.1.1.6

agnListDecodingAcmRelayPrt

This object indicates the ACM port within the slot, desired for outbound relay
(report) for the selected alarm.
notApplicable - when agnListDecodingType=sanity OR when
agnListDecodingAcmRelaySlt=notAppli…

Enumerationr/w

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.1.2.7.1.1.7

agnDlciTable

table

.1.3.6.1.4.1.164.3.1.2.8.1 · 1 row entry · 17 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnDlciTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnDlciTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

agnDlciEntry row .1.3.6.1.4.1.164.3.1.2.8.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

agnDlciCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

.1.3.6.1.4.1.164.3.1.2.8.1.1.1

agnDlciLSltIdx

This attribute indicates a unique slot position where
the card is inserted. This is the Source Slot of the DLCI.
vs=Voice Switching
In the ?004 Unit the entries io6(10)..io16) are not valid.
For ISDN BRI ports of …

Enumeration

Enumerated Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy
255	notApplicable

.1.3.6.1.4.1.164.3.1.2.8.1.1.2

agnDlciLPrtIdx

This attribute indicates a unique external or internal port number,
including linkSelector or encapsulator. This is the Source Port of the DLCI.
100=noConnect (for voice switching)
LPrtIdx is defined according one…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.8.1.1.3

agnDlciLIdx

This attribute indicates a unique index for each possible
used DLCI(16..991). This is the Source Side of the DLCI.
0=notApplicable (for voice switching)
LIdx is defined according one of the following possiblities:
1. LS…

Integer32

.1.3.6.1.4.1.164.3.1.2.8.1.1.4

agnDlciHSltIdx

This attribute indicates a unique slot position In the Mux
where the DLCI is routed to - Destination Slot.
For ISDN BRI ports of MX300/30 units:
io1(5) = isdn1(5) and io2(6) = isdn2(6)
In the ?004 Unit the entries i…

Enumeration

.1.3.6.1.4.1.164.3.1.2.8.1.1.5

agnDlciHPrtIdx

This attribute indicates a unique port number where the DLCI is
routed to - Destination Port.

SNMPv2-SMIInteger32

Constraints:
range: 1-5

.1.3.6.1.4.1.164.3.1.2.8.1.1.6

agnDlciHIdx

This attribute indicates a unique internal connection DLCI
number where the Source DLCI is routed to - the Destination Side of the DLCI.

Integer32

Enumerated Values:

1	rx
2	tx

.1.3.6.1.4.1.164.3.1.2.8.1.1.7

agnDlciTxBc

This attribute indicates a unique Tx committed bandwidth on
the user transmit line or at the port receive line.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.2.8.1.1.8

agnDlciTxBe

This attribute indicates a unique Tx excess bandwidth on the
user transmit line or at the port receive line.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	aBit1
3	aBit0
4	bBit1
5	bBit0
6	cBit1
7	cBit0
8	dBit1
9	dBit0

.1.3.6.1.4.1.164.3.1.2.8.1.1.9

agnDlciRxBc

This attribute indicates a unique Rx committed bandwidth on
the user receive line or at the port transmit line.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.2.8.1.1.10

agnDlciRxBe

This attribute indicates a unique Rx excess bandwidth on the
user receive line or at the port transmit line.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.2.8.1.1.11

agnDlciPriority

This attribute indicates a unique priority of the pcv.
1 is the lowest priority and 7 is the highest priority.

Integer32r/w

.1.3.6.1.4.1.164.3.1.2.8.1.1.12

agnDlciStatus

This attribute indicates the status of the pvc. The status is
disconnected(1) when one of the sides is programmed as
not connected

Enumeration

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.2.8.1.1.13

agnDlciSpoofing

This object refers to sending of RIP messages:
- yes : RIP messages will be sent ONLY if there is a change in the Net.
- no : RIP messages will be always sent.
This object is relevant only when one side of the …

Enumerationr/w

Constraints:
range: 1-5

.1.3.6.1.4.1.164.3.1.2.8.1.1.14

agnDlciFunnelEnable

This object selects Funnel activation:

- disabled: Funnel operation will be disabled.
The agnDlciTxBe and agnDlciTxBc values are not used for funneling.
- enabled : Funnel operation …

Enumerationr/w

Constraints:
range: 0-12

.1.3.6.1.4.1.164.3.1.2.8.1.1.15

agnDlciRoutingProtocol

This object is relevant only when one side of the DLCI is a CL-NMS interface.
It defines which Routing Protocol will be used for management via CL-NMS port.
notApplicable will be used for all slots but CL.
rip is a prop…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	legacy
3	r2Cas

.1.3.6.1.4.1.164.3.1.2.8.1.1.16

agnDlciRowStatus

This attribute allows to create/delete a row in this table.
For creating a row, the NMS should set
agnRowStatus.255.id2.id3.id4.id5.id6.id7 = active(1).
For destroying a row, the NMS should set:
agnRowStatus.255…

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.3.1.2.8.1.1.17

agnVoiceSwConfTable

table

.1.3.6.1.4.1.164.3.1.2.9.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnVoiceSwConfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnVoiceSwConfTable'

MXcess Configuration for Voice Switching.

agnVoiceSwConfEntry row .1.3.6.1.4.1.164.3.1.2.9.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

agnVoiceSwConfIdx

Active or Temporary Table.
Both configurations can be read but only the Temporary can
be written to.

Enumeration

Enumerated Values:

3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
17	io13
18	io14
19	io15
255	notApplicable

.1.3.6.1.4.1.164.3.1.2.9.1.1.1

agnVoiceSwConfZoneId

1 or 2 digits, (0-9)(1-9).

OctetStringr/w

.1.3.6.1.4.1.164.3.1.2.9.1.1.2

agnVoiceSwConfNodeId

1, 2 or 3 digits, (1-9),(0-9),(0-9).

OctetStringr/w

Constraints:
range: 1-32

.1.3.6.1.4.1.164.3.1.2.9.1.1.3

agnVoiceSwConfNoOfHops

Number of hops the frame will go through the net before deciding to discard
the frame (like time-to-live in IP).

0 = notApplicable
Default=20 .

Integer32r/w

.1.3.6.1.4.1.164.3.1.2.9.1.1.4

agnVoiceSwConfSidt

SIDT: Short Inter Digit Timeout used as timer (in sec.) between digits
after routing is completed.
The timeout indicates end of dialing and the call can then be setup.

0 = notApplicable
Default=2 sec.

Integer32r/w

Enumerated Values:

3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
17	io13
18	io14
19	io15
255	notApplicable

.1.3.6.1.4.1.164.3.1.2.9.1.1.5

agnVoiceSwConfLidt

LIDT: Long Inter Digit Timeout used as timer between digits before routing
is completed. If no digits were dialed and LIDT expired then the user will get
an error tone and the call will be disconnected.

0…

Integer32r/w

.1.3.6.1.4.1.164.3.1.2.9.1.1.6

agnVoiceSwConfDialPlan

This is the Dialing Plan method that will be used in the Voice Switching.
Static Dialing Plan - Routing is defined by the current device Zone and
Node ID in the Network.
Static Dialing Plan Plus - …

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.2.9.1.1.7

agnVoiceSwConfRtTable

table

.1.3.6.1.4.1.164.3.1.2.9.2 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnVoiceSwConfRtTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnVoiceSwConfRtTable'

Routing Table for Voice Switching.

agnVoiceSwConfRtEntry row .1.3.6.1.4.1.164.3.1.2.9.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

agnVoiceSwConfRtDbId

Active or Temporary Table.
Both configurations can be read but only the Temporary can
be written to.

Enumeration

Enumerated Values:

1	notApplicable
2	rx
3	tx
4	both
5	bcastSrc
6	bcastDst
7	internal

.1.3.6.1.4.1.164.3.1.2.9.2.1.1

agnVoiceSwConfRtIdx

The Index of the row.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.9.2.1.2

agnVoiceSwConfRtDigits

Dialed digits: Series of digits 0...9, '*', '#' or '%'.
The '*' and '#' can have many uses according to the user's decision.
For example, they can be used as part of the Dialed Number,
they exist on the phone number pan…

OctetStringr/w

.1.3.6.1.4.1.164.3.1.2.9.2.1.3

agnVoiceSwConfRtAction

Action that the system should perform for the digits:
agnVoiceSwConfRtDigits.
The action that is allowed depends on the Dialing Plan.
Here is the list of the allowed actions:
For Static Dialing Plan - zone, node, in, sh…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.2.9.2.1.4

agnVoiceSwConfRtData

This field is relevant for actions hgr(6), and rep(8), numDigDP(11)
and contains the following information:
For hgr - the number of the Hunt Group.
For rep - the number of digits to be replaced with.
For numDigDP - the …

OctetStringr/w

Enumerated Values:

1	notApplicable
2	usa
3	australia
4	brazil
5	canada
6	france
7	germany
8	israel
9	mexico
10	portugal
11	russia
12	spain
13	unitedKingdom
14	czech
15	china

.1.3.6.1.4.1.164.3.1.2.9.2.1.5

agnVoiceSwConfRtSlot

Routing Slot- Relevant for actions zone(2), node(3), shortDialing(4),
route(12), ext(13).

Enumerationr/w

.1.3.6.1.4.1.164.3.1.2.9.2.1.6

agnVoiceSwConfRtPort

Routing Port- Relevant for actions zone(2), node(3), shortDialing(4),
route(12), ext(13).
100=noConnect (for non-routing case).

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	disable
3	faxRelayT38
4	vbdPassThrou

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.9.2.1.7

agnVoiceSwConfRtDlci

Routing DLCI- Relevant for actions zone(2), node(3), shortDialing(4),
route(12), ext(13).
Valid values:
0=notApplicable (for non-routing case).
1, 16..991

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notConnected
2	r4800bps
4	r9600bps
6	r14400bps

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.9.2.1.8

agnVoiceSwConfRtRowStatus

Status of the row for creating/deleting entries in the table.
The only possible supported RowStatus vaules are
active (1), notInService (2), notReady(3), createAndGo(4),
createAndWait(5) and destroy(6).

SNMPv2-TCRowStatusr/w

Enumerated Values:

1	notApplicable
2	disable
3	vbdV152
4	vbdPassThrou

Description:

.1.3.6.1.4.1.164.3.1.2.9.2.1.9

agnVoiceSwConfRtMaxCalls

Maximum no. of simultaneous voice calls that are allowed in the direction
defined by the current entry.

Default=0 (No Limit).

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
5	g711aLAW
6	g711uLAW

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.9.2.1.10

agnVoiceSwConfRtPriority

This attribute indicates a unique priority of the Voice Switching Route.
1 is the lowest priority and 7 is the highest priority.
0 means N/A

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.9.2.1.11

agnVoiceSwConfHGTable

table

.1.3.6.1.4.1.164.3.1.2.9.5 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnVoiceSwConfHGTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnVoiceSwConfHGTable'

Table of Hunt Groups.

agnVoiceSwConfHGEntry row .1.3.6.1.4.1.164.3.1.2.9.5.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

agnVoiceSwConfHGdbIdx

Active or Temporary Table.
Both configurations can be read but only the Temporary can
be written to.

Enumeration

.1.3.6.1.4.1.164.3.1.2.9.5.1.1

agnVoiceSwConfHGIdx

For Vmux-300 devices -
This object represents a combination of
- Hunt Group number and Extension number OR
- Port number and Extension number.

For other devices (e.g. MXcess, MP-2100H) -
There may be up t…

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.9.5.1.2

agnVoiceSwConfHGConnect

This attribute indicates whether the hunt group should be
considered in any of the mux algorithms.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.2.9.5.1.3

agnVoiceSwConfHGExt

This is the extension number of the hunt group.
0 is for not valid. The allowed range is 10 - 99.

Integer32r/w

.1.3.6.1.4.1.164.3.1.2.9.5.1.4

agnVoiceSwConfHGExtString

This is the extension string of the hunt group.
This string is a combination of digits, * and #.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.3.1.2.9.5.1.5

agnVoiceSwConfHGUserParams

This object indicates the User's parameters.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.3.1.2.9.5.1.6

agnVoiceSwConfHGStatus

This object enables the user to create/delete entries in this table.
Its usage for values (1)..(6) should be identical to RowStatus SYNTAX.
notApplicable(255) - should be used when the table is static
…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.2.9.5.1.7

agnSigProfileTable

table

.1.3.6.1.4.1.164.3.1.2.10.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnSigProfileTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnSigProfileTable'

- For products supporting more than one configuration, the write operation 
into the Table is valid only to the TmpCnfg entry.
- For products that do not support configurations, the write operation 
into the Table will be to agnSigProfileCnfgIdx=1.
The table includes signaling profile parameters for Legacy Profiles.

agnSigProfileEntry row .1.3.6.1.4.1.164.3.1.2.10.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

agnSigProfileCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.
For products supporting more than one configuration,the write
operation is valid only to the TmpCnfg.
For Gmux2000 t…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.10.1.1.1

agnSigProfileIdx

This attribute indicates the Signaling Profile (1..5).
For MP-104/204, only Profile=1 will exist.

Integer32

Enumerated Values:

1	psA
2	psB
3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.1.2.10.1.1.2

agnSigProfileRxTx

This attribute indicates if the following objects refer to:
Rx or Tx translation.
Rx : ML->IO
Tx : IO->ML .
For MP-104/204, that means:
Rx : Signaling to FXS CH
Tx : Signaling to E1 Link.

Enumeration

Enumerated Values:

1	unknown
2	empty
9	acm
10	ps60W
11	ps100W
17	ps
20	cl1
21	clEth
22	cl2
23	cl2Eth
24	cl3
25	cl3Eth
26	cl1Clk
31	mPh1
32	mPh3
33	mPh1T1DSU
34	mPh1T1CSU
35	mPh1E1DSU
36	mPh1E1LTU
37	mtmlFT1
38	mtmlFE1
39	mtmlH4E1
40	mtmlH4E12W
41	mtmlH4T1
42	mtmlH4T12W
43	mtHsh4E1
44	mtHsh4E12W
45	mtHsh4T1
46	mtHsh4T12W
47	mtmlH2E1
48	mtmlH2E12W
49	mtmlH2T1
50	mtmlH2T12W
51	hsh2E1
52	hsh2E12W
53	hsh2T1
54	hsh2T12W
55	mlIp
56	mtml4Ip
57	ml20N1
58	ml20N2
60	mPl6
61	mPl3
62	vf24T1
63	vf30E1
64	vf48T1
65	vf60E1
68	ml2E1
69	ml4E1
70	ml2T1
71	ml4T1
72	mPv4
73	vc16A
74	vc8EandM
75	vc8Fxo
76	vc8Fxs
77	vc16EandM
78	vc16Fxo
79	vc16Fxs
80	vf3EandM
81	vf3Fxs
82	vf3Fxo
83	vfPbx
84	vfPbxT1
85	vfPbxE1
86	mtMlE2S
87	mtMlE2D
88	mtMlF2T1
89	mtMlF2E1
90	mtMlT1Fiber
91	mtMlE1Fiber
92	mtMlT1FiberFb
93	mtMlE1FiberFb
94	mtmlHE1
95	mtmlH1E1
96	mtmlHSE1
97	ml20
98	mtMl4T1
99	mtMl4E1
100	mtMl1T1DSU
101	mtMl1T1CSU
102	mtMl1E1DSU
103	mtMl1E1LTU
104	mtMl1T1DSUfb
105	mtMl1T1CSUfb
106	mtMl1E1DSUfb
107	mtMl1E1LTUfb
108	mtMl2T1
109	mtMl2E1
110	ls2CcittX50
111	ls2CcittX58
112	ls2ATandTSdm
113	ls2ACcittX50
114	ls2ACcittX58
115	ls2AATandTSdm
116	ls2A2Ts
117	ls2M
118	mtMlT1
119	mtMlE1
120	hs2
121	hs3
122	hsq
123	hs703
124	hsQM
125	hsqN
126	hs6
127	hs12
128	hsDp
129	hsp
130	hs4T1
131	hs4E1
132	hs4
133	hsEth
134	ml8T1
135	ml8E1
136	vc2E1
137	vc4E1
138	vc2T1
139	vc4T1
140	vc2EandM
141	vc2Fxs1Plar
142	vc2Fxo1
143	vc2Fxs2
144	vc2Fxo2
145	vc2Fxs3
146	vc2Fxo3
147	vc26EandM
148	mtvc2
149	vc2R2Fxs
150	hsu
151	mbeA
152	mbeB
153	mbeU
154	tre
155	hsuI
156	hsr
157	hss
158	hsu1
159	ls12
160	ls6
161	ls6V1EandM
162	ls6V1Fxo
163	ls6V1Fxs
164	ls6V2EandM
165	ls6V2Fxo
166	ls6V2Fxs
167	ls6VfEandM
168	ls6VfFxo
169	ls6VfFxs
170	vc3EandM
171	vc3Fxo
172	vc3Fxs
173	vcPbx
174	vcPbxT1
175	vcPbxE1
176	vc6EandM
177	vc6Fxo
178	vc6Fxs
179	vcq
180	ls6n
181	mhs1V36
182	mhs1V35
183	mhs1G703
184	mhs1DDS
185	mhs3
186	mhs1X21
187	mhs1V24
188	mhs4
189	mhsE1Hs
190	mhsT1Hs
191	mhsHyE1Hs
192	mhsHyT1Hs
193	mlfHybE1Hs
194	mlfHybT1Hs
195	mhs2e1
196	mhs2t1
197	mhsHy2e1
198	mhsHy2t1
199	mlfHybE12
200	mls6
201	mls3
202	mlHybAtmE1
203	mlHybAtmT1
204	mlfHybT12
205	mvc8
206	mvc8PbxE1
207	mvc8PbxT1Dsu
208	mvc8PbxT1Csu
209	mvc8PbxE1Slave
210	mvc4
211	mvc4PbxE1
212	mvc4PbxT1Dsu
213	mvc4PbxT1Csu
214	mvc4PbxE1Slave
215	mvc4PbxT1Slave
216	mvc8PbxT1Slave
217	mvc8ExtAnalog
218	mvcE1
219	mvcT1
220	mhsS
221	mhsU
222	mhsPriE1
223	mhsPriT1
224	hsEthSwitch
225	mPriE1FramerCcs
226	mPriT1FramerCcs
227	mPriE1SlaveCcs
228	mPriT1SlaveCcs
229	mDualBri
230	vc12EandM
231	vc12Fxo
232	vc12Fxs
233	vc6aEandM
234	vc6aFxo
235	vc6aFxs
236	vc6AgFxo
237	vc6AgFxs
238	vc6a4LB
239	vid
240	hsu12
241	hsu6
242	hss12
243	hss6
244	hsDp3
245	hsDp6
246	hsf1
247	mhsHyE1
248	mhsHyT1
249	mhsIp
250	mlIpHs
251	mlHybIpE1
252	mlHybIpT1
253	mvg1Lan
254	mvg2Lan
255	vc4Fxs
256	vc4EandM
257	vc4Fxo
258	hsf2
260	mvgSwitch4Lan
261	msl4E1W2
262	msl4E1W4
263	msl8E1W2
264	msl4E1W2Eth
265	msl8E1W2Eth
266	asmi54cE1AndEth
267	asmi54cT1AndEth
268	asmi54c
271	hs6N
272	hs12N
273	hsNRZ
281	evc2E1
282	evc4E1
283	evc2T1
284	evc4T1
285	vc2E1Pri
286	vc4E1Pri
291	vc4OmniEandM
292	vc4OmniWestern
301	clx1
302	clx1GbE
303	clx1S155
304	clx1S155GbE
305	ml8T1Eth
306	ml8E1Eth
307	op106cEth
308	op108cEth
309	op106cEthT1
310	op108cEthE1
311	op108cEthE1Unbal
312	mpw1
321	vfs24T1
322	vfs30E1
323	vfs48T1
324	vfs60E1
325	mm4E1
326	mm4T1
327	mm8E1
328	mm8T1
329	mm12E1
330	mm12T1
331	mm16E1
332	mm16T1

.1.3.6.1.4.1.164.3.1.2.10.1.1.3

agnSigProfileABCD

For MP-2100/MP-2200 and for MP-104/204 from R2:
This object represents 6 parameters, by 3 Octets :
Busy Code-MSB nibble, - applicable only for Rx translation
Idle Code- nibble, - applicable only for Rx translation
…

OctetStringr/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.1.2.10.1.1.4

agnSigProfileEcanActSignal

Echo Canceller Activation Signal.
This object specifies which BIT (A, B, C, or D) and which value (0 or 1)
will be used for the echo canceller activation. The inverse value will cause the
deactivation of the echo cancel…

Enumerationr/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.1.2.10.1.1.5

agnSigProfileEcanRespDelay

Echo Canceller Response Delay.
This object specifies the response delay in msec for the activation/deactivation
of the echo canceller.
The value should be in multiples of 100 msec: 100, 200, 300, ...2000.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

2	off
3	event
4	minor
5	major
6	warning
7	critical

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.2.10.1.1.6

agnSigProfTable

table

.1.3.6.1.4.1.164.3.1.2.10.2 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnSigProfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnSigProfTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry. This is the general table of signaling profiles.

agnSigProfEntry row .1.3.6.1.4.1.164.3.1.2.10.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

agnSigProfCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.
The write operation is valid only to the TmpCnfg.

Integer32

Enumerated Values:

2	off
3	event
4	minor
5	major
6	warning
7	critical

.1.3.6.1.4.1.164.3.1.2.10.2.1.1

agnSigProfIdx

This attribute indicates the Signaling Profile (1..5).

Integer32

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.1.2.10.2.1.2

agnSigProfName

Profile Name given by user.

OctetStringr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.1.2.10.2.1.3

agnSigProfType

Profile Type.
legacy - usual signaling. The parameters for the Legacy Profiles
are detailed in the agnSigProfileTable, above.
r2Cas - R2 signaling. The parameters for the R2 Profiles are detailed
in …

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.1.2.10.2.1.4

agnTsTable

table

.1.3.6.1.4.1.164.3.1.2.11.1 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnTsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnTsTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

agnTsEntry row .1.3.6.1.4.1.164.3.1.2.11.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

agnTsCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

.1.3.6.1.4.1.164.3.1.2.11.1.1.1

agnTsSltIdx

This attribute indicates a unique slot position where
the card is inserted.

Enumeration

.1.3.6.1.4.1.164.3.1.2.11.1.1.2

agnTsPrtIdx

This attribute indicates a unique external or internal port number.
For MP-2100, the valid values will be (for MLs only):
- exPrt1(1)..exPrt8(8)
- inPrt1(101)..inPrt8(108).
For other products' index see their specifi…

SNMPv2-SMIInteger32

Enumerated Values:

1	psA
2	psB
3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.11.1.1.3

agnTsIdx

This attribute indicates a unique index for TS (Time-Slot).
- for T1 ports - 1..24, Fbit(25)
- for E1 ports - 1..31
- for HDSL ports - 1..32 ; 32 will represent TS0.

Integer32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.1.2.11.1.1.4

agnTsBitIdx

This attribute indicates a unique index for the Bit
of each TS (Time-Slot).
1..8 - Bit 1.. Bit 8
255 - notApplicable
This object is applicable only in Split Time-Slot cases.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.11.1.1.5

agnTsConSltIdx

This attribute indicates a unique slot position In the Mux
where the TS is routed to.

Enumeration

Enumerated Values:

3	event
4	minor
5	major
6	warning
7	critical

.1.3.6.1.4.1.164.3.1.2.11.1.1.6

agnTsConPrtIdx

This attribute indicates a unique port id the TS is
routed to.
notApplicable - when agnTsType=mng or spare
For MP-2100/2200:
exPrt1 (1) .. exPrt16 (16) , notApplicable(100),
inPrt1 (101) .. inPrt48 (148).
For…

SNMPv2-SMIInteger32

Enumerated Values:

2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.11.1.1.7

agnTsConIdx

This attribute indicates a unique TS number the Src TS is
routed to.
Valid values:
- for T1 ports - 1..24, Fbit(25)
- for E1 ports - 1..31
- for HDSL ports - 1..32 ; 32 will represent TS0.
- notApplicable - 255 (fo…

Integer32

.1.3.6.1.4.1.164.3.1.2.11.1.1.8

agnTsType

Time-Slot Type - regarding its connection and media type.
voice, data, vcMP - connected and the media is specified.
mng - management. This TS is Dedicated to Management (not
disconnected, but not connected to anot…

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.1.2.11.1.1.9

agnTsRowStatus

This attribute allows to create/delete a row in this table.
For creating a row, the NMS should set
agnTsRowStatus.255.id2.id3.id4.id5.id6.id7.id8 = active(1).
For destroying a row, the NMS should set:
agnTsRowStatus.255…

SNMPv2-TCRowStatusr/w

Enumerated Values:

2	off
3	on

Description:

.1.3.6.1.4.1.164.3.1.2.11.1.1.10

agnTsDirection

Direction of the connection. This parameter is especially important
when in MP a Selected Port is connected to a Connected Port that has
no TSs, so it doesn't appear in the TS Assignment for the first 5 indexes.
notApp…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.2.11.1.1.11

systemVoiceTable

table

.1.3.6.1.4.1.164.3.1.2.12.1 · 1 row entry · 13 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk systemVoiceTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::systemVoiceTable'

General Parameters for voice - system level.

systemVoiceEntry row .1.3.6.1.4.1.164.3.1.2.12.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

systemVoiceConfIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed - Active or Temporary Configurations.
Idx 255 relates to the temporary TmpCnfg.
All configurations can be read but only the Temporary can
be written …

SNMPv2-SMIInteger32

Enumerated Values:

1	psA
2	psB
3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.12.1.1.1

systemVoiceNationalTone

Tone Characteristics (Amplitude, Frequency, delays etc.).
These characteristics are defined according to the country.

Enumerationr/w

Enumerated Values:

1	unknown
2	empty
9	acm
10	ps48x60W
11	ps48x100W
12	ps110x60W
13	ps110x100W
14	ps220x60W
15	ps220x100W
16	ps180W
17	ps
20	cl1
21	clEth
22	cl2
23	cl2Eth
24	cl3
25	cl3Eth
26	cl1Clk
31	mPh1
32	mPh3
33	mPh1T1DSU
34	mPh1T1CSU
35	mPh1E1DSU
36	mPh1E1LTU
37	mtmlFT1
38	mtmlFE1
39	mtmlH4E1
40	mtmlH4E12W
41	mtmlH4T1
42	mtmlH4T12W
43	mtHsh4E1
44	mtHsh4E12W
45	mtHsh4T1
46	mtHsh4T12W
47	mtmlH2E1
48	mtmlH2E12W
49	mtmlH2T1
50	mtmlH2T12W
51	hsh2E1
52	hsh2E12W
53	hsh2T1
54	hsh2T12W
55	mlIp
56	mtml4Ip
57	ml20N1
58	ml20N2
60	mPl6
62	vf24T1
63	vf30E1
64	vf48T1
65	vf60E1
68	ml2E1
69	ml4E1
70	ml2T1
71	ml4T1
73	vc16A
74	vc8EandM
75	vc8Fxo
76	vc8Fxs
77	vc16EandM
78	vc16Fxo
79	vc16Fxs
80	vf3EandM
81	vf3Fxs
82	vf3Fxo
83	vfPbx
84	vfPbxT1
85	vfPbxE1
86	mtMlE2S
87	mtMlE2D
88	mtMlF2T1
89	mtMlF2E1
90	mtMlT1Fiber
91	mtMlE1Fiber
92	mtMlT1FiberFb
93	mtMlE1FiberFb
94	mtmlHE1
95	mtmlH1E1
96	mtmlHSE1
97	ml20
98	mtMl4T1
99	mtMl4E1
100	mtMl1T1DSU
101	mtMl1T1CSU
102	mtMl1E1DSU
103	mtMl1E1LTU
104	mtMl1T1DSUfb
105	mtMl1T1CSUfb
106	mtMl1E1DSUfb
107	mtMl1E1LTUfb
108	mtMl2T1
109	mtMl2E1
110	ls2CcittX50
111	ls2CcittX58
112	ls2ATandTSdm
113	ls2ACcittX50
114	ls2ACcittX58
115	ls2AATandTSdm
116	ls2A2Ts
117	ls2M
118	mtMlT1
119	mtMlE1
120	hs2
121	hs3
122	hsq
123	hs703
124	hsQM
125	hsqN
126	hs6
127	hs12
128	hsDp
129	hsp
130	hs4T1
131	hs4E1
133	hsEth
134	ml8T1
135	ml8E1
136	vc2E1
137	vc4E1
138	vc2T1
139	vc4T1
140	vc2EandM
141	vc2Fxs1Plar
142	vc2Fxo1
143	vc2Fxs2
144	vc2Fxo2
145	vc2Fxs3
146	vc2Fxo3
147	vc26EandM
148	mtvc2
149	vc2R2Fxs
150	hsu
151	mbeA
152	mbeB
153	mbeU
154	tre
155	hsuI
156	hsr
157	hss
158	hsu1
159	ls12
160	ls6
161	ls6V1EandM
162	ls6V1Fxo
163	ls6V1Fxs
164	ls6V2EandM
165	ls6V2Fxo
166	ls6V2Fxs
167	ls6VfEandM
168	ls6VfFxo
169	ls6VfFxs
170	vc3EandM
171	vc3Fxo
172	vc3Fxs
173	vcPbx
174	vcPbxT1
175	vcPbxE1
176	vc6EandM
177	vc6Fxo
178	vc6Fxs
179	vcq
180	ls6n
181	mhs1V36
182	mhs1V35
183	mhs1G703
184	mhs1DDS
185	mhs3
186	mhs1X21
187	mhs1V24
188	mhs4
189	mhsE1Hs
190	mhsT1Hs
191	mhsHyE1Hs
192	mhsHyT1Hs
193	mlfHybE1Hs
194	mlfHybT1Hs
195	mhs2e1
196	mhs2t1
197	mhsHy2e1
198	mhsHy2t1
199	mlfHybE12
200	mls6
201	mls3
202	mlHybAtmE1
203	mlHybAtmT1
204	mlfHybT12
205	mvc8
206	mvc8PbxE1
207	mvc8PbxT1Dsu
208	mvc8PbxT1Csu
209	mvc8PbxE1Slave
210	mvc4
211	mvc4PbxE1
212	mvc4PbxT1Dsu
213	mvc4PbxT1Csu
214	mvc4PbxE1Slave
215	mvc4PbxT1Slave
216	mvc8PbxT1Slave
217	mvc8ExtAnalog
218	mvcE1
219	mvcT1
220	mhsS
221	mhsU
222	mhsPriE1
223	mhsPriT1
224	hsEthSwitch
225	mPriE1FramerCcs
226	mPriT1FramerCcs
227	mpriE1SlaveCcs
228	mpriT1SlaveCcs
229	mDualBri
230	vc12EandM
231	vc12Fxo
232	vc12Fxs
233	vc6aEandM
234	vc6aFxo
235	vc6aFxs
236	vc6AgFxo
237	vc6AgFxs
238	vc6a4LB
239	vid
240	hsu12
241	hsu6
242	hss12
243	hss6
244	hsDp3
245	hsDp6
246	hsf1
247	mhsHyE1
248	mhsHyT1
249	mhsIp
250	mlIpHs
251	mlHybIpE1
252	mlHybIpT1
253	mvg1Lan
254	mvg2Lan
255	vc4Fxs
256	vc4EandM
257	vc4Fxo
258	hsf2
260	mvgSwitch4Lan
261	msl4E1W2
262	msl4E1W4
263	msl8E1W2
264	msl4E1W2Eth
265	msl8E1W2Eth
266	asmi54cE1AndEth
267	asmi54cT1AndEth
268	asmi54c
271	hs6N
272	hs12N
273	hsNRZ
281	evc2E1
282	evc4E1
283	evc2T1
284	evc4T1
285	vc2E1Pri
286	vc4E1Pri
291	vc4OmniEandM
292	vc4OmniWestern
301	clx1
302	clx1GbE
303	clx1S155
304	clx1S155GbE
305	ml8T1Eth
306	ml8E1Eth
307	op106cEth
308	op108cEth
309	op106cEthT1
310	op108cEthE1
311	op108cEthE1Unbal
312	mpw1
321	vfs24T1
322	vfs30E1
323	vfs48T1
324	vfs60E1

.1.3.6.1.4.1.164.3.1.2.12.1.1.2

systemVoicePacketRate

This object indicates the G.729 and G.711 Coders
transmitted Packet Rate in milliseconds.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.2.12.1.1.3

systemVoiceFaxSupport

This object allows the user to Disable/Enable Fax support.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.2.12.1.1.4

systemVoiceFaxRate

This object indicates the Fax Rate limit.
It is irrelevant when Fax support is NA or disabled.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	standAlone
3	integrated

.1.3.6.1.4.1.164.3.1.2.12.1.1.5

systemVoiceModemSupport

This object allows the user to Disable/Enable Modem support.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.1.2.12.1.1.6

systemVoiceCoderAndRate

This object indicates the Coder and Rate for the Voice Compression.

Enumerationr/w

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.1.2.12.1.1.7

systemVoiceEchoCanceler

This object indicates the Echo Canceler activation.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.2.12.1.1.8

systemVoiceTxGain

This object indicates the Transmit Gain (volume) in dB.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.2.12.1.1.9

systemVoiceDtmfRelayMethod

This object indicates the DTMF Relay Method
that is used to transmit DTMF tones.

rfc2833(1) - inband DTMF relay according to RFC-2833.
sipInfo(2) - out of band DTMF relay using SIP INFO method.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.2.12.1.1.10

systemVoiceDtmfRelayRxPayloadType

This object indicates the Rx Payload Type
for DTMF relay RTP packets.
It is relevant only when DTMF Relay Method is RFC-2833.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.2.12.1.1.11

systemVoiceDtmfRelayPayloadTypeNeg

This object indicates whether Payload Type Negotiation is used
(according to RFC-2833) or not.
It is relevant only when DTMF Relay Method is RFC-2833.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.2.12.1.1.12

systemVoiceDtmfRelayTxPayloadType

This object indicates the Tx Payload Type
for DTMF relay RTP packets.
It is relevant only when the Payload Type Negotiation is disabled.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.2.12.1.1.13

systemVoiceCoderTable

table

.1.3.6.1.4.1.164.3.1.2.12.2 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk systemVoiceCoderTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::systemVoiceCoderTable'

Voice Coders table.

systemVoiceCoderEntry row .1.3.6.1.4.1.164.3.1.2.12.2.1

An entry in Voice Coders table.

Indexes

No indexes recorded

Column	Syntax	OID
systemVoiceCoderConfIdx The first index of the table. This object might represent the Configuration Index (1..100) being accessed; Index=255 relates to the TmpCnfg. For devices with multiple configurations, Set is permitted to T…	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.2.12.2.1.1`
systemVoiceCoderPriority This object indicates the Coder's Priority.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.2.12.2.1.2`
systemVoiceCoderCoderAndRate This object indicates the Coder and Rate for the Voice Compression.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.2.12.2.1.3`

mdlSInstTable

table

.1.3.6.1.4.1.164.3.1.3.1.1 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlSInstTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlSInstTable'

A table.

mdlSInstEntry row .1.3.6.1.4.1.164.3.1.3.1.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

mdlSInstSltIdx

A unique number to identify a slot position in the mux.
In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io(16)
are not valid.
For the Vmux2100 Main Board clA (3) is used.

Enumeration

.1.3.6.1.4.1.164.3.1.3.1.1.1.1

mdlSInstCardType

This attribute indicates the type of card installed
in the specific slot position.
Only PS cards are possible in the PS slots.
Only CL cards are possible in the CL slots.
Only IO cards are possible in the IO slots.

Enumeration

.1.3.6.1.4.1.164.3.1.3.1.1.1.2

mdlSHwVersion

This attribute indicates the Hardware version of the
installed card in the specific slot position.

OctetString

.1.3.6.1.4.1.164.3.1.3.1.1.1.3

mdlSSwVersion

This attribute indicates the Software version of the
installed card in the specific slot position.

OctetString

Enumerated Values:

3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.1.3.1.1.1.4

mdlSAlrStatus

Indicates the alarm state at module level, i.e. lower level
(port alarms) status is not included.
This attribute will be set to:
critical(7) - when there is at least one active (state ON)
critical alar…

Enumeration

.1.3.6.1.4.1.164.3.1.3.1.1.1.5

mdlSAlrStatusAll

Indicates the alarm state in the module-all level, i.e. lower level
(port alarms) included.
This attribute will be set to:
critical(7) - when there is at least one active (state ON)
critical alarm,
…

Enumeration

Enumerated Values:

2	external
3	internal
4	highSpeedV35
5	highSpeedV24
6	highSpeedV36
7	highSpeedX21
8	highSpeedG703
9	highSpeedDDS
10	lowSpeed
11	voice
12	cl
13	isdns
14	isdnu
15	ethernet
16	voiceS0
17	voiceU
18	voiceQsigS
19	voiceQsigU

.1.3.6.1.4.1.164.3.1.3.1.1.1.6

mdlSMaskedAlrStat

Indicates the alarm state at module level, [i.e. lower level
(port alarms) status is not included],including Masked alarms.
This attribute will be set to:
critical(7) - when there is at least one active (state ON)
…

Enumeration

.1.3.6.1.4.1.164.3.1.3.1.1.1.7

mdlSMaskedAlrStatAll

Indicates the alarm state in the module-all level, i.e. lower level
(port alarms) included, including Masked alarms.
This attribute will be set to:
critical(7) - when there is at least one active (state ON)
…

Enumeration

Enumerated Values:

1	unknown
2	notUsed
3	offLine
4	onLine
5	offLineRedundancy
6	onLineRedundancy

.1.3.6.1.4.1.164.3.1.3.1.1.1.8

mdlSTstStatusAll

This attribute will be set to on(3) when there is at least
one test in progress on a channel of the card, otherwise
the value will be off(2).

Enumeration

Enumerated Values:

2	off
3	event
4	minor
5	major
6	warning
7	critical

.1.3.6.1.4.1.164.3.1.3.1.1.1.9

mdlSClearAlrCmd

Setting this command to ON, enforces a clear of all the
alarms in the given slot, excluding alarms of port level.
The clear operation will not be applied for masked/inverted
alarms.

Enumerationr/w

Enumerated Values:

2	off
3	event
4	minor
5	major
6	warning
7	critical

.1.3.6.1.4.1.164.3.1.3.1.1.1.10

mdlSClearAllAlrCmd

Setting this command to ON, enforces a clear of all the
alarms in the given slot, including all its ports alarms.
The clear operation will not be applied for masked/inverted
alarms.

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.1.3.1.1.1.11

mdlSTemperature

Temperature of the card, in Celsius degrees.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.3.1.1.1.12

mdlSAlrTable

table

.1.3.6.1.4.1.164.3.1.3.1.2 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlSAlrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlSAlrTable'

The list of card agent alarms ; includes also an alarm
indicating existence of alarms on its ports if there are any.

mdlSAlrEntry row .1.3.6.1.4.1.164.3.1.3.1.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

mdlSAlrIdx

A unique number to identify an entry in the alarm status table.
Users should use the get next function to read this table because
the indexes are not consecutive.

SNMPv2-SMIInteger32

Enumerated Values:

2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.3.1.2.1.1

mdlSAlrSltIdx

This attribute indicates the desired slot position.
In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io12(16)
are not valid.
For the Vmux2100 Main Board clA (3) is used.

Enumeration

.1.3.6.1.4.1.164.3.1.3.1.2.1.2

mdlSAlrCodeDescription

This attribute is a full text description of the alarm .
The alarm description includes the following information:
alarm code, alarm text, alarm severity, Masked or Inverted
flag and counter.

OctetString

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.1.3.1.2.1.3

mdlSAlrCode

A code identifying the alarm of an entry in the alarm status
table at card level.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.3.1.2.1.4

mdlSAlrSeverity

The severity of the alarm.

Enumeration

.1.3.6.1.4.1.164.3.1.3.1.2.1.5

mdlSAlrState

State of the alarm.

Enumeration

Enumerated Values:

1	noRdn
2	offline
3	online

.1.3.6.1.4.1.164.3.1.3.1.2.1.6

mdlSAlrCounter

A counter - how many times the alarm occured since last
clear operation.
ON and OFF Alarm will be counted separately.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.3.1.2.1.7

mdlSAlrMask

Alarm mask : on/off.

Enumeration

.1.3.6.1.4.1.164.3.1.3.1.2.1.8

mdlSAlrInvert

Alarm invert : on/off.

Enumeration

.1.3.6.1.4.1.164.3.1.3.1.2.1.9

mdlCPrgTable

table

.1.3.6.1.4.1.164.3.1.3.2.1 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlCPrgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlCPrgTable'

A table.

mdlCPrgEntry row .1.3.6.1.4.1.164.3.1.3.2.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

mdlCCnfgIdx

This attribute indicates the Idx of the Cnfg(1..100) being
referred.
Value 255 specifies the TmpCnfg

Integer32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.1.3.2.1.1.1

mdlCSltIdx

This attribute indicates a unique number of the slot
position where the card is inserted.
In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16)
are not valid.

Enumeration

.1.3.6.1.4.1.164.3.1.3.2.1.1.2

mdlCPrgCardType

This attribute indicates the type of card assigned to the
specific slot in the common configuration.
This object is identical in all the configurations (1..100).
Only the TmpCnf(255) may have different value.
The write …

Enumerationr/w

Enumerated Values:

3	event
4	minor
5	major
6	warning
7	critical

.1.3.6.1.4.1.164.3.1.3.2.1.1.3

mdlCNoOfExternPrt

Number of external ports in the programmed card of the
specific slot position

SNMPv2-SMIInteger32

Enumerated Values:

2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.3.2.1.1.4

mdlCNoOfInternPrt

Number of internal ports in the programmed card of the
specific slot position.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.3.2.1.1.5

mdlCWorkMode

Working mode of the card.
The user may configure the card to work in a stand alone mode or integrated
with the device.

Example for use in MHS-IP cards:

- standAlone - in this mode, the …

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.1.3.2.1.1.6

mdlCDhcpClientEnable

Enable/Disable the feature of DHCP Client for the selected card.

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.1.3.2.1.1.7

mdlCRdnExists

This object indicates whether any port of the programmed card is
configured to be part of a Redundancy/APS pair.
If at least one port of the programmed card is configured to be
part of a Redundancy/APS pair, the value w…

Enumeration

Enumerated Values:

1	unknown
2	empty
17	ps
20	cl1
26	cl1Clk
62	vf24T1
63	vf30E1
64	vf48T1
65	vf60E1
74	vc8EandM
75	vc8Fxo
76	vc8Fxs
77	vc16EandM
78	vc16Fxo
79	vc16Fxs
134	ml8T1
135	ml8E1
156	hsr
159	ls12
180	ls6n
224	hsEthSwitch
240	hsu12
241	hsu6
255	vc4Fxs
256	vc4EandM
257	vc4Fxo
261	msl4E1W2
263	msl8E1W2
264	msl4E1W2Eth
265	msl8E1W2Eth
266	asmi54cE1AndEth
267	asmi54cT1AndEth
268	asmi54c
271	hs6N
272	hs12N
301	clx1
302	clx1GbE
303	clx1S155
304	clx1S155GbE
305	ml8T1Eth
306	ml8E1Eth
307	op106cEth
308	op108cEth
309	op106cEthT1
310	op108cEthE1
311	op108cEthE1Unbal
312	mpw1
321	vfs24T1
322	vfs30E1
323	vfs48T1
324	vfs60E1

.1.3.6.1.4.1.164.3.1.3.2.1.1.8

mdlCInterfaces

Octet string which indicates 'present' interfaces in card.
Each '0' bit stands for non-present interface.
Each '1' bit stands for present interface.

For ASMi54C card of LRS-102 and MP-4100 notPresent in…

OctetString

.1.3.6.1.4.1.164.3.1.3.2.1.1.9

mdlCmprTable

table

.1.3.6.1.4.1.164.3.1.3.3.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlCmprTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlCmprTable'

A table.

mdlCmprEntry row .1.3.6.1.4.1.164.3.1.3.3.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

mdlCmprTypIdx

This attribute indicates the Type of the Compressed being
referred.

SNMPv2-SMIInteger32

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.3.3.1.1.1

mdlCmprCnfgIdx

This attribute indicates the configuration to which the
Compressed information is related.

SNMPv2-SMIInteger32

Enumerated Values:

1	currentInv
2	last

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.3.3.1.1.2

mdlCmprVersion

This attribute indicates the version of the internal format
of the Compressed data

SNMPv2-SMIInteger32

Constraints:
range: 0-899

.1.3.6.1.4.1.164.3.1.3.3.1.1.3

mdlCmprSltIdx

This attribute indicates a unique number of the slot
position where the card is inserted.
In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16)
are not valid.

Enumeration

.1.3.6.1.4.1.164.3.1.3.3.1.1.4

mdlCmprObj

This attribute is the compressed information itself.

OctetStringr/w

.1.3.6.1.4.1.164.3.1.3.3.1.1.5

mdlAlarmsCmprTable

table

.1.3.6.1.4.1.164.3.1.3.3.2 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlAlarmsCmprTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlAlarmsCmprTable'

A table.

mdlAlarmsCmprEntry row .1.3.6.1.4.1.164.3.1.3.3.2.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
mdlAlarmsCmprVersion This attribute indicates the version of the internal format of the Compressed data	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.3.3.2.1.1`
mdlAlarmsCmprAlarmSlot This attribute indicates the desired slot position. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io(16) are not valid.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.3.3.2.1.2`
mdlAlarmsCmprAlarmIdx A unique number to identify an entry in the alarm status table of the agent.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.3.3.2.1.3`
mdlAlarmsCmprObj This attribute is the compressed information itself.	OctetStringr/w	`.1.3.6.1.4.1.164.3.1.3.3.2.1.4`

prtSInstTable

table

.1.3.6.1.4.1.164.3.1.4.1.1 · 1 row entry · 17 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtSInstTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtSInstTable'

A table.

prtSInstEntry row .1.3.6.1.4.1.164.3.1.4.1.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtSInstSltIdx

This attribute indicates a unique number to identify the
slot where the card is inserted.
In the ?004 Unit the entries io6(10)..io(16) are not valid.
For the Vmux2100 Main Board clA (3) is used.

Enumeration

.1.3.6.1.4.1.164.3.1.4.1.1.1.1

prtSInstPrtIdx

This attribute indicates a unique number to identify a port
in a specific card.
The valid ports depend on the installed card:
the valid external ports (interfaces) are (1..mdlCNoOfExternPrt) if any,
and the valid intern…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.1.1.1.2

prtSInstPrtType

This attribute describes the type of the designated port.
In MX 3000 only external & internal options are used.
All the other options are only for MX 30/300 which need special handling.
In order to support interface typ…

Enumeration

.1.3.6.1.4.1.164.3.1.4.1.1.1.3

prtSInstIfIndex

This attribute indicates the unique interface number
assigned to the port. The specific interface of this
attribute is the same as the interface identified by the
value of ifindex in MIB-II.If there is no interface f…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.1.1.1.4

prtSActiveStatus

This attribute describes the activity status of the port.
unknown(1) indicates that the information is not supported.
notUsed(2) indicates that the ch is not connected according
to the active config.
offLine(…

Enumeration

.1.3.6.1.4.1.164.3.1.4.1.1.1.5

prtSAlrStatus

Indicates the alarm state in the port(ch) agent level.
This attribute will be set to:
critical(7) - when there is at least one active (state ON)
critical alarm,
otherwise it will be set to
major…

Enumeration

.1.3.6.1.4.1.164.3.1.4.1.1.1.6

prtSMaskedAlrStat

Indicates the alarm state in the port(ch) agent level,
including Masked alarms.
This attribute will be set to:
critical(7) - when there is at least one active (state ON)
critical alarm,
otherwise i…

Enumeration

.1.3.6.1.4.1.164.3.1.4.1.1.1.7

prtSClearAlrCmd

Setting this attribute to on(3) enforces a clear operation
of the alarm status events in the given port. The clear
operation will not be applied for masked/inverted alarms.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.4.1.1.1.8

prtSTestMask

This is a mask which indicates which tests from the
'prtSTstCmd' list are allowed for the requested port.
If a specific test is allowed, its respective bit
will be SET in the mask :

TEST …

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.1.1.1.9

prtSTstCmd

Setting this attribute to any of the above values will
initiate a test on the specific port if the operation is
legal. If the operation is not legal, the mux will ignore
the operation.
testPerTS(31) - when this test…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.4.1.1.1.10

prtSTstDuration

This attribute indicates the maximum duration of executing
a test on the specific port. This entry applies to all the
test operations. The resolution will be a minute, and the
maximum duration is limited to 30 minutes.
…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.1.1.1.11

prtSBertClrCmd

Setting this attribute initiates bert count clear operation.
It is valid only when bert test is active on the specific
port.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.4.1.1.1.12

prtSBertTstRslt

This attribute indicates the number of Bit Error Rate
indicated during the BERT operation.
It is valid only when bert test is active on the specific
port.

SNMPv2-SMIInteger32

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.1.1.1.13

prtSInterfaceType

This attribute indicates a unique HW interface type of the
selected port.

OctetString

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6

.1.3.6.1.4.1.164.3.1.4.1.1.1.14

prtSParamStatus

This object indicates Status of parameters specific to the
selected port.
- For a port that has no special status or is supported
by prtSExHsfStatTable - 1 Octet: 00hex

- For VC-6, VC-6A, VC-6AG, VC-6A/…

OctetString

Enumerated Values:

1	currentInv
2	last

.1.3.6.1.4.1.164.3.1.4.1.1.1.15

prtSTestMaskXp

This is an Expanded test mask of the prtSTestMask object.
The prtSTestMask object reached its maximum, being an Integer with 32 bits.
This object indicates which tests from the 'prtSTstCmdXP' list are
allowed for the …

OctetStringr/w

Constraints:
range: 0-899

.1.3.6.1.4.1.164.3.1.4.1.1.1.16

prtSRdnStatus

Redundancy Status of this port.
noRdn - this port is not part of a Redundancy pair/group.
offline - this port is offline from Redundancy point of view.
online - this port is online from Redundancy point of view.

Enumeration

.1.3.6.1.4.1.164.3.1.4.1.1.1.17

prtSAlrTable

table

.1.3.6.1.4.1.164.3.1.4.1.2 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtSAlrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtSAlrTable'

The list of port agent alarms.

prtSAlrEntry row .1.3.6.1.4.1.164.3.1.4.1.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtSAlrIdx

A unique number to identify an entry in the alarm status table.
Users should use the get next function to read this table because
the indexes are not consecutive

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.1.2.1.1

prtSAlrSltIdx

This attribute indicates a unique identifier of the slot
where the card is inserted.
In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io12(16)
are not valid.
For the Vmux2100 Main Board clA (3) is used.

Enumeration

.1.3.6.1.4.1.164.3.1.4.1.2.1.2

prtSAlrPrtIdx

This attribute indicates a unique identifier of the port
the alarm applies to.
All the values are valid. No alarms exist for a port
which does not exist.
Valid valuesfor MP-2100/2200: exPrt1 (1) .. exPrt16 (16) ,
…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.1.2.1.3

prtSAlrCodeDescription

This attribute is a full text description of the alarm.
The alarm description includes the following information:
alarm code, alarm text, alarm severity, Masked or Inverted
flag and counter.

OctetString

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.1.4.1.2.1.4

prtSAlrCode

A code identifying the alarm of an entry in the alarm status
table at port level.

SNMPv2-SMIInteger32

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.1.2.1.5

prtSAlrSeverity

The severity of the alarm.

Enumeration

Constraints:
range: 1-991

.1.3.6.1.4.1.164.3.1.4.1.2.1.6

prtSAlrState

State of the alarm.

Enumeration

.1.3.6.1.4.1.164.3.1.4.1.2.1.7

prtSAlrCounter

A counter - how many times the alarm occured since last
clear operation.
ON and OFF Alarm will be counted separately.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.1.2.1.8

prtSAlrMask

Alarm mask : on/off.

Enumeration

.1.3.6.1.4.1.164.3.1.4.1.2.1.9

prtSAlrInvert

Alarm invert : on/off.

Enumeration

.1.3.6.1.4.1.164.3.1.4.1.2.1.10

prtSAlrCardType

This attribute indicates the type of card installed
in the specific slot position. The enumeration is according
to mdlSInstCardType.

Enumeration

.1.3.6.1.4.1.164.3.1.4.1.2.1.11

prtFrStatisTable

table

.1.3.6.1.4.1.164.3.1.4.1.3.1.1 · 1 row entry · 24 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtFrStatisTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtFrStatisTable'

This table is applicable only for an active port running an
FR protocol .

prtFrStatisEntry row .1.3.6.1.4.1.164.3.1.4.1.3.1.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtFrStatisSltIdx

This attribute indicates a unique slot position where
the module is inserted.
In the ?004 Unit the entries io6(10)..io12(16) are not valid.
For stand-alone units this index will be notApplicable (255).

Enumeration

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.1

prtFrStatisPrtIdx

This attribute indicates a unique port number.

Enumeration

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.2

prtFrStatisInvIdx

The Interval of 15 min. for which the following statistics
counters are applicable.

Enumeration

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.3

prtFrTimeElapsed

The number of seconds that have elapsed since the
beginning of the current error-measurement interval.
This object is applicable mainly for the current interval.
For other interval:
- if data is available: value will b…

Integer32

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.4

prtFrRxTotalFrames

The total number of frames received by this port during the
selected interval.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.5

prtFrTxTotalFrames

The total number of frames sent by this port during the
selected interval.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.6

prtFrRxTotalBytes

The total number of bytes received by this port during the
selected interval.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.7

prtFrTxTotalBytes

The total number of bytes sent by this port during the
selected interval.

SNMPv2-SMICounter32

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.8

prtFrRxMngFrames

The management number of frames received by this port
during the selected interval.

SNMPv2-SMICounter32

Enumerated Values:

exPrt1

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.9

prtFrTxMngFrames

The management number of frames sent by this port during the
selected interval.

SNMPv2-SMICounter32

Enumerated Values:

1	tx
2	rx

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.10

prtFrRxDeFrames

The number of De frames received by this port during the
selected interval.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.11

prtFrTxDeFrames

The number of De frames sent by this port during the
selected interval.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.12

prtFrRxDcrdCongDeFr

The number of De frames discarded due to congestion,
received by this port during the selected interval.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.13

prtFrTxDcrdCongDeFr

The number of De frames discarded due to congestion,
sent by this port during the selected interval.

SNMPv2-SMICounter32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.14

prtFrRxDcrdCongAllFr

All the frames discarded due to congestion,
received by this port during the selected interval.

SNMPv2-SMICounter32

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.15

prtFrTxDcrdCongAllFr

All the frames discarded due to congestion,
sent by this port during the selected interval.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.16

prtFrRxFecn

Number of frames received by this port during the
selected interval, indicating forward congestion.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.17

prtFrTxFecn

Number of frames sent by this port during the
selected interval, indicating forward congestion.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.18

prtFrRxBecn

Number of frames received by this port during the
selected interval, indicating backward congestion.

SNMPv2-SMICounter32

Enumerated Values:

2	noConnect
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.19

prtFrTxBecn

Number of frames sent by this port during the
selected interval, indicating backward congestion.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.20

prtFrRxBeViol

Number of data frames received by this port during the
selected interval, exceeding the Burst Excess value.

SNMPv2-SMICounter32

Enumerated Values:

1	none
8	remoteBert
30	localBert
255	notApplicable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.21

prtFrTxBeViol

Number of data frames sent by this port during the
selected interval, exceeding the Burst Excess value.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.22

prtFrRxBcViol

Number of data frames received by this port during the
selected interval, exceeding the Burst Committed value.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.23

prtFrTxBcViol

Number of data frames sent by this port during the
selected interval, exceeding the Burst Committed value.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.24

prtCrStatisTable

table

.1.3.6.1.4.1.164.3.1.4.1.3.2.1 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtCrStatisTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtCrStatisTable'

This table is applicable only for an active port running a
CR protocol .

prtCrStatisEntry row .1.3.6.1.4.1.164.3.1.4.1.3.2.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtCrStatisSltIdx

Enumeration

.1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.1

prtCrStatisPrtIdx

This attribute indicates a unique port number.

Enumeration

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.2

prtCrStatisInvIdx

The Interval of 15 min. for which the following statistics
counters are applicable.

Enumeration

.1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.3

prtCrTimeElapsed

Integer32

.1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.4

prtCrRxTotalCells

The total number of cells received by this port during the
selected interval.

SNMPv2-SMICounter32

Enumerated Values:

1	notApplicable
2	off
3	on

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.5

prtCrTxTotalCells

The total number of cells sent by this port during the
selected interval.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.6

prtCrRxDataCells

The number of Data Cells received by this port during the
selected interval.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.7

prtCrTxDataCells

The number of Data Cells sent by this port during the
selected interval.

SNMPv2-SMICounter32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.8

prtDlciStatisTable

table

.1.3.6.1.4.1.164.3.1.4.1.3.3.1 · 1 row entry · 15 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtDlciStatisTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtDlciStatisTable'

This table is applicable only for an active port running an
FR, FR+ or CR protocol, with valid DLCIs .

prtDlciStatisEntry row .1.3.6.1.4.1.164.3.1.4.1.3.3.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtDlciSltIdx

Enumeration

Enumerated Values:

1	monday
2	tuesday
3	wednesday
4	thursday
5	friday
6	saturday
7	sunday

.1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.1

prtDlciPrtIdx

This attribute indicates a unique port number.

Enumeration

Constraints:
range: 1-4

.1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.2

prtDlciIdx

This attribute indicates a unique DLCI index for each valid
DLCI (16..991).

Integer32

Constraints:
range: 0-86400

.1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.3

prtDlciRxDeFrames

The number of De frames received by this DLCI.

SNMPv2-SMICounter32

Constraints:
range: 0-86400

.1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.4

prtDlciTxDeFrames

The number of De frames sent by this DLCI.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.5

prtDlciRxDcrdCongDeFr

The number of De frames discarded due to congestion,
received by this DLCI.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.6

prtDlciTxDcrdCongDeFr

The number of De frames discarded due to congestion,
sent by this DLCI.

SNMPv2-SMICounter32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.7

prtDlciRxDcrdCongAllFr

All the frames discarded due to congestion,
received by this DLCI.

SNMPv2-SMICounter32

Enumerated Values:

3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.8

prtDlciTxDcrdCongAllFr

All the frames discarded due to congestion,
sent by this DLCI.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.9

prtDlciTxFecn

Number of frames sent by this DLCI, indicating forward
congestion.

SNMPv2-SMICounter32

Enumerated Values:

3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.10

prtDlciTxBecn

Number of frames sent by this DLCI, indicating backward
congestion.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.11

prtDlciRxBeViol

Number of data frames received by this DLCI, exceeding the
Burst Excess value.

SNMPv2-SMICounter32

Constraints:
range: 0-16777215

.1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.12

prtDlciTxBeViol

Number of data frames sent by this DLCI, exceeding the Burst
Excess value.

SNMPv2-SMICounter32

Enumerated Values:

1	notApplicable
2	partial
3	full
4	partialCD

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.13

prtDlciRxBcViol

Number of data frames received by this DLCI, exceeding the
Burst Committed value.

SNMPv2-SMICounter32

Enumerated Values:

1	notApplicable
2	off
3	on

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.14

prtDlciTxBcViol

Number of data frames sent by this DLCI, exceeding the Burst
Committed value.

SNMPv2-SMICounter32

Enumerated Values:

1	none
2	rip2
3	proprietaryRip
255	notApplicable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.15

prtT1FdlMsgTable

table

.1.3.6.1.4.1.164.3.1.4.1.3.4.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtT1FdlMsgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtT1FdlMsgTable'

This table is applicable for a T1 interface with 'esf'
LineType .

prtT1FdlMsgEntry row .1.3.6.1.4.1.164.3.1.4.1.3.4.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtT1FdlMsgSltIdx

This attribute indicates a unique slot position where
the module is inserted.
In the ?004 Unit the entries io6(10)..io12(16) are not valid.

Enumeration

Enumerated Values:

3	legacy
4	abcd
5	none

.1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.1

prtT1FdlMsgPrtIdx

This attribute indicates a unique port number.
MTML-1/T1 modules have just one external interface.

Enumeration

.1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.2

prtT1FdlMsgFdlTxRx

The Fdl tx/rx reference of the Fdl message.

Enumeration

.1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.3

prtT1FdlMsg

FDL message.

OctetString

.1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.4

prtExTsSplitTable

table

.1.3.6.1.4.1.164.3.1.4.2.1 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExTsSplitTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExTsSplitTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry, except prtExTsBitTest that will be
written directly to the Active Configuration.

prtExTsSplitEntry row .1.3.6.1.4.1.164.3.1.4.2.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtExTsCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

Enumerated Values:

1	psA
2	psB
3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.1.4.2.1.1.1

prtExTsSltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io12(16) are not valid.
notApplicable - for stand-alone units.

Enumeration

.1.3.6.1.4.1.164.3.1.4.2.1.1.2

prtExTsPrtIdx

This attribute indicates a unique port number.
Most ML cards have only one external interface.
inPrt1 - for MTML-H/E1 cards.
For other products' index see their specification.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.2.1.1.3

prtExTsIdx

This attribute indicates a unique time slot position.
The valid time slots are:
1..24 for T1 Card and
1..31 for E1 interface.
In G732S-E1 lines, time slot 16 is not valid for data,
it is dedicated to multiframe synchro…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.2.1.1.4

prtExTsBit

This attribute indicates a unique Bit within the time slot.
The valid Bits are: 1..8.
255=NA.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.2.1.1.5

prtExTsIConSlot

This attribute indicates whether the specified time slot is
connected/routed internally in the Agent and to which card
it is connected.
In the ?004 Unit the entries io6(10)..io12(16) are not valid.
notApplicable - for s…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.4.2.1.1.6

prtExTsIConPrt

This attribute indicates the internally (In Mux)
connected/routed port.
For other products' index see their specification.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.2.1.1.7

prtExTsBitTest

This attribute indicates a test to be activated on the selected Bit.
It is applicable only when prtExPh1MlTsTest=split(254).
none - no test is applied for the selected Bit.
notApplicable - when prtExPh1MlTsTest is NOT s…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.4.2.1.1.8

prtExTsTxSignaling

Link - Tx Signaling per TS, for TSs having TS Type=Voice
(agnTsType=voice(2)).
It monitors what is sent to Link for the selected TS,
for A,B,C,D Signaling Bits.
Bit 1= LSB
Bit 8= MSB
Bit 1-2 = A Signaling Bit: 00='…

OctetString

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.1.4.2.1.1.9

prtExTsRxSignaling

Link - Rx Signaling per TS, for TSs having TS Type=Voice
(agnTsType=voice(2)).
It monitors what is received from Link for the selected TS,
for A,B,C,D Signaling Bits.
Bit 1= LSB
Bit 8= MSB
Bit 1-2 = A Signaling Bit:…

OctetString

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6
7	exPrt7
8	exPrt8
9	exPrt9
10	exPrt10
101	inPrt1
102	inPrt2
103	inPrt3
104	inPrt4
105	inPrt5
106	inPrt6
107	inPrt7
108	inPrt8
109	inPrt9
110	inPrt10
111	inPrt11
112	inPrt12

.1.3.6.1.4.1.164.3.1.4.2.1.1.10

prtExTsTxIoSignaling

IO - Tx Signaling per TS, for TSs having TS Type=Voice
(agnTsType=voice(2)).
It monitors what is sent to IO port for the selected TS,
for A,B,C,D Signaling Bits.
Bit 1= LSB
Bit 8= MSB
Bit 1-2 = A Signaling Bit: 00=…

OctetString

.1.3.6.1.4.1.164.3.1.4.2.1.1.11

prtExTsRxIoSignaling

IO - Rx Signaling per TS, for TSs having TS Type=Voice
(agnTsType=voice(2)).
It monitors what is received from IO port for the selected TS,
for A,B,C,D Signaling Bits.
Bit 1= LSB
Bit 8= MSB
Bit 1-2 = A Signaling Bit…

OctetString

.1.3.6.1.4.1.164.3.1.4.2.1.1.12

prtAgendaBehaviourTable

table

.1.3.6.1.4.1.164.3.1.4.2.2.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtAgendaBehaviourTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtAgendaBehaviourTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtAgendaBehaviourEntry row .1.3.6.1.4.1.164.3.1.4.2.2.1.1

An entry in table.

Indexes

prtAlarmsCmprVersion prtAlarmsCmprAlarmSlot prtAlarmsCmprAlarmPort prtAlarmsCmprAlarmIdx

Column	Syntax	OID
prtAgendaBehaviourCnfgIdx This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.	Integer32	`.1.3.6.1.4.1.164.3.1.4.2.2.1.1.1`
prtAgendaBehaviourSltIdx This parameter should be: - slot number for MX3000 - 255 = N/A for MX300/30.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.4.2.2.1.1.2`
prtAgendaBehaviourPrtIdx This parameter should be: - port number for MX300/30 - 100 = N/A for MX3000.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.4.2.2.1.1.3`
prtAgendaBehaviourOnOff Setting this command to on(3) enables the agenda function at module (3000) or port (300/30) level.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.4.2.2.1.1.4`

prtCnfgAgendaTable

table

.1.3.6.1.4.1.164.3.1.4.2.2.2 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtCnfgAgendaTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtCnfgAgendaTable'

This table allows the user to schedule the time a session
is active per week basis.

prtCnfgAgendaEntry row .1.3.6.1.4.1.164.3.1.4.2.2.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtCnfgAgendaCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

.1.3.6.1.4.1.164.3.1.4.2.2.2.1.1

prtCnfgAgendaSltIdx

This attribute is equal to:
-slot number for MX3000
-255 = N/A for MX300/30

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.2.2.2.1.2

prtCnfgAgendaPrtIdx

This attribute is equal to:
- port number for MX300/30
- port number for MX3000. For example 1-4 in MHS-4 cards.
- 100 = N/A for MX3000 when not used.

SNMPv2-SMIInteger32

Enumerated Values:

2	noConnect
3	clA
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.2.2.2.1.3

prtCnfgAgendaDayIdx

This attribute for which day of the week this row applies.

Enumeration

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6
7	exPrt7
8	exPrt8
9	exPrt9
10	exPrt10
11	exPrt11
12	exPrt12
100	noConnect
101	inPrt1
102	inPrt2
103	inPrt3
104	inPrt4
105	inPrt5
106	inPrt6
107	inPrt7
108	inPrt8
109	inPrt9
110	inPrt10
111	inPrt11
112	inPrt12

.1.3.6.1.4.1.164.3.1.4.2.2.2.1.4

prtCnfgAgendaSesId

The user may define 4 different active intervals per day.

Integer32

Enumerated Values:

1	unknown
2	down
3	up

.1.3.6.1.4.1.164.3.1.4.2.2.2.1.5

prtCnfgAgendaFrom

Start from time interval in seconds.

Integer32r/w

.1.3.6.1.4.1.164.3.1.4.2.2.2.1.6

prtCnfgAgendaTo

To time interval in seconds.

Integer32r/w

.1.3.6.1.4.1.164.3.1.4.2.2.2.1.7

prtGenCnfgTable

table

.1.3.6.1.4.1.164.3.1.4.2.3 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtGenCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtGenCnfgTable'

This table allows the user to configure general
port parameters.

prtGenCnfgEntry row .1.3.6.1.4.1.164.3.1.4.2.3.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtGenCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.
The write operation is valid only to the TmpCnfg.

Integer32

Enumerated Values:

1	filtered
2	transparent

.1.3.6.1.4.1.164.3.1.4.2.3.1.1

prtGenCnfgSltIdx

This attribute indicates a unique slot position where
the card is inserted.

Enumeration

Enumerated Values:

1	notApplicable
2	withCRC
3	withoutCRC

.1.3.6.1.4.1.164.3.1.4.2.3.1.2

prtGenCnfgPrtIdx

This attribute indicates a unique external or internal port number.
For MP:
exPrt1 (1) .. exPrt16 (16) ,
notApplicable(100),
inPrt1 (101) .. inPrt84 (184)

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.2.3.1.3

prtGenCnfgLinkToSlot

This attribute indicates the slot of the ML card to which
the IO port is mapped.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.1.4.2.3.1.4

prtGenCnfgLinkToPort

This attribute indicates the port in the prtGenCnfgLinkToSlot of
the ML card to which the IO port is mapped.
For MP:
exPrt1 (1) ,
exPrt2 (2) ,
exPrt3 (3) ,
exPrt4 (4) ,
exPrt5 (5) ,
exPrt6 (6) ,
exPrt7…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	notSkip
3	skip

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.2.3.1.5

prtGenCnfgPortId

IO Port Id for V5.1 use.
This object is applicable only for part of the PSTN and ISDN IO ports.
Generally, 0 is a valid value.
Nevertheless, for ports that do not support this object, the value
will be: notApplic…

Integer32r/w

Enumerated Values:

1	notApplicable
2	unBlock
3	block

.1.3.6.1.4.1.164.3.1.4.2.3.1.6

prtGenCnfgBusConnection

This object indicates the support of the card regarding Bus Connection.
Same value for all ports of the card.
partial = 2 Buses (AB)
full = 4 Buses (ABCD)
partial CD = 2 Buses CD
Actually the support depends on the c…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	unBlock
3	block

.1.3.6.1.4.1.164.3.1.4.2.3.1.7

prtGenCnfgInbandMng

This object indicates whether Inband Management is used over the
link.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	s10Mbps
3	s100Mbps
4	s1Gbps

.1.3.6.1.4.1.164.3.1.4.2.3.1.8

prtGenCnfgInbandMngRoutProt

This object indicates the Inband Mng Routing Protocol of
the port.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.1.4.2.3.1.9

prtGenCnfgProtectionMode

This object indicates the Protection Mode of the port.
notApplicable- when Bus Protection Point=No.
For VC-4/Omni card this object is supported RO.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	none
3	fixed

.1.3.6.1.4.1.164.3.1.4.2.3.1.10

prtGenCnfgConnect

This object indicates whether the port should be considered in
any of the mux algorithms.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	no
3	yes
4	localOnly

.1.3.6.1.4.1.164.3.1.4.2.3.1.11

prtGenCnfgSignalingType

This object selects the Type of Signaling used by the port.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.4.2.3.1.12

prtCmprTable

table

.1.3.6.1.4.1.164.3.1.4.3.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtCmprTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtCmprTable'

A table.

prtCmprEntry row .1.3.6.1.4.1.164.3.1.4.3.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtCmprTypIdx

This attribute indicates the Type of the Compressed being
referred.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.3.1.1.1

prtCmprCnfgIdx

This attribute indicates the configuration to which the
Compressed information is related.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.3.1.1.2

prtCmprVersion

This attribute indicates the version of the internal format of
the Compressed data

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.3.1.1.3

prtCmprSltIdx

This attribute indicates a unique number of the slot position
where the card is inserted.
In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16)
are not valid.

Enumeration

Enumerated Values:

2	disable
3	passive

.1.3.6.1.4.1.164.3.1.4.3.1.1.4

prtCmprPrtIdx

This attribute indicates a unique identifier of the port
the compressed information relates to.
Valid values: exPrt1 (1) .. exPrt16 (16) ,
inPrt1 (101) .. inPrt48 (148).

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	none
3	proprietary
4	rip2
6	rip1and2

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.4.3.1.1.5

prtCmprObj

This attribute is the compressed information itself.

OctetStringr/w

Enumerated Values:

1	crossOver
2	straightThrough

.1.3.6.1.4.1.164.3.1.4.3.1.1.6

prtCmprStatisticObj

This attribute is the compressed statistics information itself.

OctetString

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.1.4.3.1.1.7

prtDlciCmprTable

table

.1.3.6.1.4.1.164.3.1.4.3.2 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtDlciCmprTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtDlciCmprTable'

A table.

prtDlciCmprEntry row .1.3.6.1.4.1.164.3.1.4.3.2.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
prtDlciCmprCnfgIdx This attribute indicates the configuration to which the Compressed information is related.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.4.3.2.1.1`
prtDlciCmprVersion This attribute indicates the version of the internal format of the Compressed data	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.4.3.2.1.2`
prtDlciCmprSltIdx This attribute indicates a unique number of the slot position where the module is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid.	Enumeration	`.1.3.6.1.4.1.164.3.1.4.3.2.1.3`
prtDlciCmprPrtIdx This attribute indicates a unique identifier of the port the compressed information relates to. All the values are valid.	Enumeration Constraints: `range: 4-4`	`.1.3.6.1.4.1.164.3.1.4.3.2.1.4`
prtDlciCmprDlciIdx This attribute indicates a unique identifier of the Dlci the compressed information relates to. The values are between 16 - 991.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.4.3.2.1.5`
prtDlciCmprObj This attribute is the compressed information itself.	OctetStringr/w	`.1.3.6.1.4.1.164.3.1.4.3.2.1.6`

prtAlarmsCmprTable

table

.1.3.6.1.4.1.164.3.1.4.3.3 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtAlarmsCmprTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtAlarmsCmprTable'

A table.

prtAlarmsCmprEntry row .1.3.6.1.4.1.164.3.1.4.3.3.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
prtAlarmsCmprVersion This attribute indicates the version of the internal format of the Compressed data	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.4.3.3.1.1`
prtAlarmsCmprAlarmSlot This attribute indicates the desired slot position. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io(16) are not valid. For Stand-alone units, notApplicable(255) will appear.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.4.3.3.1.2`
prtAlarmsCmprAlarmPort This attribute indicates a unique identifier of the port the alarm applies to. All the values are valid. No alarms exist for a non-existing port. IP Bundles are considered a port too, for this matter.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.4.3.3.1.3`
prtAlarmsCmprAlarmIdx A unique number to identify an entry in the alarm status table of the agent.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.4.3.3.1.4`
prtAlarmsCmprObj This attribute is the compressed information itself.	OctetString	`.1.3.6.1.4.1.164.3.1.4.3.3.1.5`

agnLinkMapTable

table

.1.3.6.1.4.1.164.3.1.5.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnLinkMapTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnLinkMapTable'

A table.

agnLinkMapEntry row .1.3.6.1.4.1.164.3.1.5.1.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
mapLinkId A unique identifier of the link	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.5.1.1.1`
mapLinkSltIdx This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries clA(3), io6(10)..io12(16) are not valid.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.5.1.1.2`
mapLinkPrtIdx This attribute indicates a unique port number.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.5.1.1.3`
mapLinkStatus This attribute indicates the status of the link between the two muxes	Enumeration	`.1.3.6.1.4.1.164.3.1.5.1.1.4`

ethIfTable

table

.1.3.6.1.4.1.164.3.1.6.1.1 · 1 row entry · 25 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ethIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ethIfTable'

A table.

ethIfEntry row .1.3.6.1.4.1.164.3.1.6.1.1.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
ethIfIdx A unique index of the ethernet interface/port.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.6.1.1.1.1`
ethMode This object indicates the Ethernet mode of operation.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.2`
ethBridgingMode This object indicates the bridging mode of the Ethernet interface.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.3`
ethEncapsulationCRCMode This object define the encapsulation type requested for the Ethernet interface. It indicates if we transfer the Ethernet frame to the other side with or without the CRC.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.4`
ethBackPressure This parameter defines whether to enable or disable Back pressure. Back Pressure is a flow control parameter.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.5`
ethLimit4 This parameter determine the Back off algorithm mode. Every 4 following collisions the Framer will be thrown out (4 times more than usuall).	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.6`
ethSkipInitReset This parameter defines whether read status on reset.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.7`
ethMulticastBlock This parameter defines whether to send multicast message to WAN from LAN or not.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.8`
ethBroadcastBlock This parameter defines whether to send broadcast message to WAN from LAN or not.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.9`
ethSpeed This parameter defines the line speed.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.10`
ethRip2 This parameter defines whether to send RIP II message to WAN from LAN or not	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.11`
ethPortPriority This parameter defines if priority is to be considered for this Port.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.12`
ethPortMngEnable This parameter defines whether management data can pass through this Port. localOnly (4) - Only local device can be managed via this port.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.13`
ethFlowCtrlMacAddress In case of flow control - transmit frame with this specific MAC address to inform the other end to stop sending frames. Default: 01.80.C2.00.00.01.	MacAddressr/w Type Constraints: `range: 6`	`.1.3.6.1.4.1.164.3.1.6.1.1.1.14`
ethRateLimit This parameter defines the Rate Limit of the line, in Mbps.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.6.1.1.1.15`
ethJumboFrameEnable This parameter defines whether to support Jumbo Frame or not.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.16`
ethAutoMdiXEnable This parameter defines whether to support automatic change between MDI and MDI[X].	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.17`
ethPortDataEnable This parameter defines whether this port is enabled for data (that is not management). no(2) - management can run on this port yes(3) - both management and payload data can run on this port.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.18`
ethIfUse This parameter defines the use of the port. 1=NET 2=USER .	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.6.1.1.1.19`
ethLineOam This parameter defines the working mode of 802.AH OAM mechanism.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.20`
ethRoutingProtocol This parameter defines the routing protocol used above ETH port.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.21`
ethMdiXManualSwitch This parameter sets the port to be MDI-X (cross-over) or MDI (straight-through). It is applicable only when ethAutoMdiXEnable = no, namely, only when the automatic MDI/MDIX crossover function is disabled.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.22`
ethDot1xEnable Determines if the Port-Based Network Access Protocol (IEEE-802.1x) is enabled for the Ethernet Port.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.23`
ethPartnerRateMode For converters having couples of ports, where each couple contains a port with an SFP connector and a port with a RJ connector, this parameter is relevant for the SFP port. It affects Rate configuration of its part…	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.24`
ethDot1xPortRole Determine the functionality of the port in the Port-Based Network Access Protocol (IEEE-802.1x) - either Authenticator or Supplicant.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.1.1.25`

ethIfCurrentTable

table

.1.3.6.1.4.1.164.3.1.6.1.2.1 · 1 row entry · 42 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ethIfCurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ethIfCurrentTable'

The Ethernet Current table.
When the index specifies the Ethernet interface (only), the counters
are for an interval of 15 minutes.

ethIfCurrentEntry row .1.3.6.1.4.1.164.3.1.6.1.2.1.1

An entry in the Ethernet Current table.

Indexes

No indexes recorded

Column	Syntax	OID
ethIfCurrentIndex The index of the Ethernet interface. It may be ifIndex. For some devices (e.g RICi-622GE), supporting several types of intervals, this index will be a concatenation of the port index and interval type. Interval ty…	SNMPv2-SMIInteger32 Constraints: `range: 4-4`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.1`
ethIfCurrentStatus The status of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.	OctetString	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.2`
ethIfCurrentInFrames The counter associated with the number of received frames, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.3`
ethIfCurrentInOctets The counter associated with the number of received octets, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.4`
ethIfCurrentAlignmentErrors The counter associated with the number of received frames, which are not complete (The result of dividing the number of bits by 8 is not an Integer), encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.5`
ethIfCurrentFCSErrors The counter associated with the number of received frames that didn't pass the FCS test, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.6`
ethIfCurrentLengthError The counter associated with the number of received frames with length error, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.7`
ethIfCurrentOutFrames The counter associated with the number of transmitted frames, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.8`
ethIfCurrentOutOctets The counter associated with the number of transmitted octets, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.9`
ethIfCurrentSingleCollisionFrames The counter associated with the number of successfully transmitted frames for which transmission was inhibited by exactly one collision, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.10`
ethIfCurrentMultipleCollisionFrames The counter associated with the number of successfully transmitted frames for which transmission was inhibited by more than one collision, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.11`
ethIfCurrentDeferredTransmissions The counter associated with the number of transmitted frames for which the first transmission attempt was delayed due to a busy media, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.12`
ethIfCurrentLateCollisions The counter associated with the number of times that a collision was detected later than the first 64 bytes of the frame, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.13`
ethIfCurrentCarrierSenseErrors The counter associated with the number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.14`
ethIfCurrentInputCongestionDropped The counter associated with the number of frames dropped due to lack of buffers in ingress pool, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.15`
ethIfCurrentOutputCongestionDropped The counter associated with the number of dropped frames due to a congestion, encountered by the Transmit direction to the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.16`
ethIfCurrentOverflowInFrames The number of times the associated ethIfCurrentInFrames counter has overflowed in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.17`
ethIfCurrentOverflowInOctets The number of times the associated ethIfCurrentInOctets counter has overflowed in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.18`
ethIfCurrentOverflowFCSErrors The number of times the associated ethIfCurrentFCSErrors counter has overflowed in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.19`
ethIfCurrentOverflowOutFrames The number of times the associated ethIfCurrentOutFrames counter has overflowed in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.20`
ethIfCurrentOverflowOutOctets The number of times the associated ethIfCurrentOutOctets counter has overflowed in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.21`
ethIfCurrentOverflowMultipleCollisionFrames The number of times the associated ethIfCurrentMultipleCollisionFrames counter has overflowed in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.22`
ethIfCurrentInUnicastFrames The number of received Unicast frames, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.23`
ethIfCurrentOutUnicastFrames The number of transmitted Unicast frames, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.24`
ethIfCurrentInMulticastFrames The number of received Multicast frames, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.25`
ethIfCurrentOutMulticastFrames The number of transmitted Multicast frames, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.26`
ethIfCurrentInBroadcastFrames The number of received Broadcast frames, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.27`
ethIfCurrentOutBroadcastFrames The number of transmitted Broadcast frames, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.28`
ethIfCurrentInDiscardFrames The number of received Discarded frames, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.29`
ethIfCurrentOutDiscardFrames The number of transmitted Discarded frames, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.30`
ethIfCurrentInPauseFrames The number of received Pause frames, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.31`
ethIfCurrentOutPauseFrames The number of transmitted Pause frames, encountered by the Ethernet interface in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.32`
ethIfCurrentOverflowInUnicastFrames The number of times the associated ethIfCurrentInUnicastFrames counter has overflowed in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.33`
ethIfCurrentOverflowOutUnicastFrames The number of times the associated ethIfCurrentOutUnicastFrames counter has overflowed in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.34`
ethIfCurrentOverflowInMulticastFrames The number of times the associated ethIfCurrentInMulticastFrames counter has overflowed in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.35`
ethIfCurrentOverflowOutMulticastFrames The number of times the associated ethIfCurrentOutMulticastFrames counter has overflowed in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.36`
ethIfCurrentOverflowInBroadcastFrames The number of times the associated ethIfCurrentInBroadcastFrames counter has overflowed in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.37`
ethIfCurrentOverflowOutBroadcastFrames The number of times the associated ethIfCurrentOutBroadcastFrames counter has overflowed in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.38`
ethIfCurrentOverflowInDiscardFrames The number of times the associated ethIfCurrentInDiscardFrames counter has overflowed in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.39`
ethIfCurrentOverflowOutDiscardFrames The number of times the associated ethIfCurrentOutDiscardFrames counter has overflowed in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.40`
ethIfCurrentOverflowInPauseFrames The number of times the associated ethIfCurrentInPauseFrames counter has overflowed in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.41`
ethIfCurrentOverflowOutPauseFrames The number of times the associated ethIfCurrentOutPauseFrames counter has overflowed in the current interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.1.1.42`

ethIfIntervalTable

table

.1.3.6.1.4.1.164.3.1.6.1.2.2 · 1 row entry · 43 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ethIfIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ethIfIntervalTable'

The Ethernet Interval table.
When ethIfIntervalIndex specifies the Ethernet interface (only), 
the counters are for an interval of 15 minutes.

ethIfIntervalEntry row .1.3.6.1.4.1.164.3.1.6.1.2.2.1

An entry in the Ethernet Interval table.

Indexes

No indexes recorded

Column Syntax OID

ethIfIntervalIndex

The index of the Ethernet interface.
It may be ifIndex.
For some devices (e.g RICi-622GE), supporting several types of
intervals, this index will be a concatenation of the port index and
interval type.
Interval typ…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.1

ethIfIntervalNumber

The Interval Number. This number is between 1 and x, where 1 is the
most recently completed interval and x is the least recently
completed interval.
For 15 minute intervals, usually x=96, but it can be different,
depe…

Integer32

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.2

ethIfIntervalStatus

The status of the interval:
0 - Valid.
1 - redundantLinkSwitch - the link has been switched
by a redundancy mechanism.
2 - discontinuity - module was partialy out.
4 - notValid - module is out.

OctetString

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.3

ethIfIntervalInFrames

The counter associated with the number of received frames,
encountered by the Ethernet interface in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.4

ethIfIntervalInOctets

The counter associated with the number of received octets,
encountered by the Ethernet interface in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.5

ethIfIntervalAlignmentErrors

The counter associated with the number of received frames,
which are not complete (The result of dividing the number
of bits by 8 is not an Integer), encountered by the Ethernet
interface in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.6

ethIfIntervalFCSErrors

The counter associated with the number of received frames
that didn't pass the FCS test, encountered by the Ethernet
interface in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.7

ethIfIntervalLengthError

The counter associated with the number of received frames
with length error, encountered by the Ethernet interface in
the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.8

ethIfIntervalOutFrames

The counter associated with the number of transmitted frames,
encountered by the Ethernet interface in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.9

ethIfIntervalOutOctets

The counter associated with the number of transmitted octets,
encountered by the Ethernet interface in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.10

ethIfIntervalSingleCollisionFrames

The counter associated with the number of successfully
transmitted frames for which transmission was inhibited by
exactly one collision, encountered by the Ethernet
interface in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.11

ethIfIntervalMultipleCollisionFrames

The counter associated with the number of successfully
transmitted frames for which transmission was inhibited by
more than one collision, encountered by the Ethernet
interface in the interval.

SNMPv2-SMIGauge32

Enumerated Values:

2	disabled
3	initiate
4	react

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.12

ethIfIntervalDeferredTransmissions

The counter associated with the number of transmitted frames
for which the first transmission attempt was delayed due to a
busy media, encountered by the Ethernet interface in the interval.

SNMPv2-SMIGauge32

Enumerated Values:

2	disabled
3	ccBased
4	lbBased

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.13

ethIfIntervalLateCollisions

The counter associated with the number of times that a
collision was detected later than the first 64 bytes of the
frame, encountered by the Ethernet interface in the interval.

SNMPv2-SMIGauge32

Constraints:
range: 0-7

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.14

ethIfIntervalCarrierSenseErrors

The counter associated with the number of times that the
carrier sense condition was lost or never asserted when
attempting to transmit a frame, encountered by the Ethernet
interface in the interval.

SNMPv2-SMIGauge32

Enumerated Values:

1	unicast
2	multicast

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.15

ethIfIntervalInputCongestionDropped

The counter associated with the number of dropped frames
due to a congestion, encountered by the Receive direction
to the Ethernet interface in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.16

ethIfIntervalOutputCongestionDropped

The counter associated with the number of dropped frames
due to a congestion, encountered by the Transmit direction
to the Ethernet interface in the interval.

SNMPv2-SMIGauge32

Constraints:
range: 0-7

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.17

ethIfIntervalOverflowInFrames

The number of times the associated ethIfIntervalInFrames
counter has overflowed in the interval.

SNMPv2-SMIGauge32

Enumerated Values:

1	notApplicable
2	fail
3	ok
4	mismerge
5	unexpectedMep
6	unexpectedMeLevel

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.18

ethIfIntervalOverflowInOctets

The number of times the associated ethIfIntervalInOctets
counter has overflowed in the interval.

SNMPv2-SMIGauge32

Enumerated Values:

1	proprietary
2	standard

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.19

ethIfIntervalOverflowFCSErrors

The number of times the associated ethIfIntervalFCSErrors
counter has overflowed in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.20

ethIfIntervalOverflowOutFrames

The number of times the associated ethIfIntervalOutFrames
counter has overflowed in the interval.

SNMPv2-SMIGauge32

Enumerated Values:

1	primaryVid
2	charString
3	unsignedInt16
4	rfc2865VpnId
32	icc

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.21

ethIfIntervalOverflowOutOctets

The number of times the associated ethIfIntervalOutOctets
counter has overflowed in the interval.

SNMPv2-SMIGauge32

Constraints:
range: 1-45

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.22

ethIfIntervalOverflowMultipleCollisionFrames

The number of times the associated ethIfIntervalMultipleCollisionFrames
counter has overflowed in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.23

ethIfIntervalInUnicastFrames

The number of received Unicast frames, encountered by the
Ethernet interface in the interval.

SNMPv2-SMIGauge32

Enumerated Values:

0	intervalInvalid
1	interval300Hz
2	interval10ms
3	interval100ms
4	interval1s
5	interval10s
6	interval1min
7	interval10min

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.24

ethIfIntervalOutUnicastFrames

The number of transmitted Unicast frames, encountered by the
Ethernet interface in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.25

ethIfIntervalInMulticastFrames

The number of received Multicast frames, encountered by the
Ethernet interface in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.26

ethIfIntervalOutMulticastFrames

The number of transmitted Multicast frames, encountered by the
Ethernet interface in the interval.

SNMPv2-SMIGauge32

Enumerated Values:

2	no
3	yes

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.27

ethIfIntervalInBroadcastFrames

The number of received Broadcast frames, encountered by the
Ethernet interface in the interval.

SNMPv2-SMIGauge32

Constraints:
range: 1-1024

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.28

ethIfIntervalOutBroadcastFrames

The number of transmitted Broadcast frames, encountered by the
Ethernet interface in the interval.

SNMPv2-SMIGauge32

Constraints:
range: 0-7

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.29

ethIfIntervalInDiscardFrames

The number of received Discarded frames, encountered by the
Ethernet interface in the interval.

SNMPv2-SMIGauge32

Enumerated Values:

2	no
3	yes

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.30

ethIfIntervalOutDiscardFrames

The number of transmitted Discarded frames, encountered by the
Ethernet interface in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.31

ethIfIntervalInPauseFrames

The number of received Pause frames, encountered by the
Ethernet interface in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.32

ethIfIntervalOutPauseFrames

The number of transmitted Pause frames, encountered by the
Ethernet interface in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.33

ethIfIntervalOverflowInUnicastFrames

The number of times the associated ethIfIntervalInUnicastFrames
counter has overflowed in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.34

ethIfIntervalOverflowOutUnicastFrames

The number of times the associated ethIfIntervalOutUnicastFrames
counter has overflowed in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.35

ethIfIntervalOverflowInMulticastFrames

The number of times the associated ethIfIntervalInMulticastFrames
counter has overflowed in the interval.

SNMPv2-SMIGauge32

Enumerated Values:

2	no
3	yes

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.36

ethIfIntervalOverflowOutMulticastFrames

The number of times the associated ethIfIntervalOutMulticastFrames
counter has overflowed in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.37

ethIfIntervalOverflowInBroadcastFrames

The number of times the associated ethIfIntervalInBroadcastFrames
counter has overflowed in the interval.

SNMPv2-SMIGauge32

Enumerated Values:

2	off
3	on

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.38

ethIfIntervalOverflowOutBroadcastFrames

The number of times the associated ethIfIntervalOutBroadcastFrames
counter has overflowed in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.39

ethIfIntervalOverflowInDiscardFrames

The number of times the associated ethIfIntervalInDiscardFrames
counter has overflowed in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.40

ethIfIntervalOverflowOutDiscardFrames

The number of times the associated ethIfIntervalOutDiscardFrames
counter has overflowed in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.41

ethIfIntervalOverflowInPauseFrames

The number of times the associated ethIfIntervalInPauseFrames
counter has overflowed in the interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.42

ethIfIntervalOverflowOutPauseFrames

The number of times the associated ethIfIntervalOutPauseFrames
counter has overflowed in the interval.

SNMPv2-SMIGauge32

Constraints:
range: 0-7

.1.3.6.1.4.1.164.3.1.6.1.2.2.1.43

ethIfPerfTable

table

.1.3.6.1.4.1.164.3.1.6.1.2.4 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ethIfPerfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ethIfPerfTable'

The Ethernet Performance table.

ethIfPerfEntry row .1.3.6.1.4.1.164.3.1.6.1.2.4.1

An entry in the Ethernet Performance table.

Indexes

No indexes recorded

Column	Syntax	OID
ethIfPerfInOkFrames The counter associated with the number of received OK frames, encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statistics was done.	SNMPv2-SMIGauge32 Constraints: `range: 0-50000`	`.1.3.6.1.4.1.164.3.1.6.1.2.4.1.1`
ethIfPerfOutOkFrames The counter associated with the number of transmitted OK frames, encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statistics was done.	SNMPv2-SMIGauge32 Constraints: `range: 0-50000`	`.1.3.6.1.4.1.164.3.1.6.1.2.4.1.2`
ethIfPerfTotalCollisions The counter associated with the total number of collisions of any type encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statistics was done	SNMPv2-SMIGauge32 Constraints: `range: 3-10`	`.1.3.6.1.4.1.164.3.1.6.1.2.4.1.3`
ethIfPerfInOkOctets The counter associated with the number of received OK Octets, encountered by the Ethernet interface since ethPerformanceMode Set to countOK (2) or Reset Statistics was done.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.2.4.1.4`

radMepTable

table

.1.3.6.1.4.1.164.3.1.6.1.3.1 · 1 row entry · 33 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radMepTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radMepTable'

MEG End Point (MEP) configuration table associated with 
Maitenance Entity Group (MEG) End Point.
MEP is a short name for an expanded ETH flow point that includes a compound
ETH Segment flow termination function, which marks the end point of an ETH ME,
and a compound ETH Diagnostic flow function.

radMepEntry row .1.3.6.1.4.1.164.3.1.6.1.3.1.1

An entry in the table.

Indexes

No indexes recorded

Column Syntax OID

radOamIdx1

This object may indicate the Bridge Index or Configuration index.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.1

radOamEvcIdx

This object indicates the Index of the EVC (Ethernet Virtual Circuit)
that the MEP is associated to.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.2

radMepIdx

This object indicates the ID of the MEP being accessed.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.3

radMepRowStatus

This attribute allows to create/delete a row in this table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.4

radMepLocalMepId

This object indicates the local MEP ID.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.5

radMepRemoteMepId

This atribute is currently implemneted at radMepCcTable, that
supports multicast.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.6

radMepOamMode

This object determines the OAM mode of the MEP:
disabled - no CC is initiated nor responded
initiate - the device initiates and responds to CC
react - the device does not initiate a CC, but responds to CC.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.7

radMepContinuityVerMode

This object determines the OAM behavior of the MEP:
disabled - no CC is done
cc_based - CC is done based on incoming messages
lb_based - CC is done based on loopback messages.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.8

radMepMeLevel

At any point in a network, ME Level is used to distinguish between OAM
signals belonging to different nested MEs.
Maintenance Entity Levels are defined as follows:
0,1,2 are assigned to customers
3,4 are assigned to …

Unsigned32r/w

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.9

radMepOamDestAddrType

This object determines if the OAM messages are sent to user defined
unicast address, or to RAD proprietary multicast address.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.10

radMepOamDestMacAddr

This object determines the MAC address that OAM packets are sent to.

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.11

radMepDefaultPriority

This object defines the priority of the OAM messages sent when no
service is defined on EVC. If a service is defined, the OAM messages
will get the highest service priority existing on the EVC.

Unsigned32r/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.12

radMepCcStatus

This object indicates the Continuity Check (CC)
status.

Enumeration

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.13

radMepOamProtocol

Determines whether to use proprietary OAM mechanism,
or to use the standard (IEEE 802.1ag, ITU-T Y.1731).

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.14

radMepMdId

The index of the Maintenance Domain in the radMdTable (radMdIndex).

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.15

radMepMaFormat

The type (and thereby format) of the Maintenance Association
Name.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.16

radMepMaName

The Short Maintenance Association name.

OctetStringr/w

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.17

radMepSpVlanId

The SP (Service Provider) VLAN used when sending an OAM message.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.18

radMepCcInterval

Indicates the interval at which CCMs are sent by a MEP
Valid only if radMepOamMode = initiate(4).

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.19

radMepTransmitLbmDestMacAddress

The Target MAC Address Field to be transmitted in the Loopback Message:
For unicast MAC Address this is the unicast destination MAC address.
For multicast MAC Address, this variable is read-only.
This address will be u…

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.20

radMepTransmitLbmDestMepId

The MEPID of another MEP in the same MA to which the
LBM is to be sent. This address will be used if the value of
radMepTransmitLbmDestIsMepId is yes (3).
802.1ag clause 12.14.7.3.2:b.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.21

radMepTransmitLbmDestIsMepId

yes (3) indicates that MEPID of the target MEP is used for loopback transmission.
no (2) indicates that unicast destination MAC address of the target MEP is used.
802.1ag clause 12.14.7.3.2:b.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.22

radMepTransmitLbmMassages

The number of Loopback messages to be transmitted.

Integer32r/w

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.23

radMepTransmitLbmVlanPriority

The priority to be used in the VLAN tag, if present,
in the transmitted frame.
The default value is CCM priority.
802.1ag clause 12.14.7.3.2:e

Unsigned32r/w

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.24

radMepTransmitLbmVlanDropEnable

Drop Enable bit to be used in the VLAN tag, if present,
in the transmitted frame.
802.1ag clause 12.14.7.3.2:e

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.25

radMepLbrIn

Total number of valid, in-order Loopback Replies received.

SNMPv2-SMICounter32

Constraints:
range: 0-899

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.26

radMepLbrInOutOfOrder

The total number of valid, out-of-order Loopback Replies
received.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.27

radMepLbmOut

Total number of Loopback Messages transmitted.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.28

radMepTransmitLtmTargetMacAddress

The Target MAC Address Field to be transmitted in the Link Trace Message:
A unicast destination MAC address.
This address will be used
if the value of radMepTransmitLtmTargetIsMepId is no (2).
802.1ag clause 12.14.…

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.29

radMepTransmitLtmTargetMepId

The MEPID of another MEP in the same MA to which
LTM is to be transmitted. This address will be used
if the value of radMepTransmitLtmTargetIsMepId is yes (3).
802.1ag clause 12.14.7.4.2:c.

SNMPv2-SMIUnsigned32r/w

Constraints:
range: 1-96

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.30

radMepTransmitLtmTargetIsMepId

yes (3) indicates that MEPID of the target MEP is used for Linktrace transmission.
no (2) indicates that unicast destination MAC address of the target MEP is used.
802.1ag clause 12.14.7.4.2:c.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.31

radMepTransmitLtmTtl

The LTM TTL field. Default value, if not specified, is 64.
The TTL field indicates the number of hops remaining to the LTM.
Decremented by 1 each Linktrace Responder that handles the LTM.
The value received in the LTM i…

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.32

radMepTransmitLtmActivationCmd

Activation command for starting Loop Trace. Set will be always
to 'on' value. After operation was finished, Agent will turn the value to 'off'.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.1.3.1.1.33

ethOamServiceTable

table

.1.3.6.1.4.1.164.3.1.6.1.3.2.1 · 1 row entry · 23 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ethOamServiceTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ethOamServiceTable'

Service configuration table associated with Services running on a MEP.

ethOamServiceEntry row .1.3.6.1.4.1.164.3.1.6.1.3.2.1.1

An entry in the table.

Indexes

No indexes recorded

Column Syntax OID

ethOamServiceIdx

This object indicates the Index of the service being accessed.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.1

ethOamServiceRowStatus

This attribute allows to create/delete a row in this table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.2

ethOamServicePriority

This object determines the priority of the service.
It is sent as P bits in an OAM message originated by this service.

Unsigned32r/w

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.3

ethOamServicePmEnable

This object determines PM (Performance Monitoring)
shall be enabled or not for the service.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.4

ethOamServiceFrameLossRatioThresh

This object determines the Frame Loss ratio threshold in exponent
of 1/10. That is, a value of 4 means that the threshold is 1E-4.

Integer32r/w

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.5

ethOamServiceDelayThresh

This object determines the delay threshold defined for this service,
in measurement unit of 0.1 msec.

Integer32r/w

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.6

ethOamServiceDelayVarThresh

This object determines the delay variation threshold defined
for this service, in measurement unit of 0.1 msec.

Integer32r/w

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.7

ethOamServiceUnavailRatioThresh

This object determines the Unavailability ratio threshold in exponent
of 1/10. That is, a value of 4 means that the threshold is 1E-4.

Integer32r/w

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.8

ethOamServiceTxFrames

Counts the number of frames trnasmitted by since the time the service is up.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.9

ethOamServiceOverflowTxFrames

The number of times the associated
ethOamServiceTxFrames counter has overflowed.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.10

ethOamServiceFrameLoss

Counts the number of frames lost since the time the service is up.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.11

ethOamServiceOverflowFrameLoss

The number of times the associated
ethOamServiceFrameLoss counter has overflowed.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.12

ethOamServiceFrameLossRatio

Indicates the ratio of the lost frames since the time the service is up.
The value is the ratio multiplied by 1E10.
0xFFFFFFFF will be returned for ratio greater than 4/10 (40%).

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.13

ethOamServiceElapsedTime

Indicates the time elapsed in seconds since the time the service is up.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.14

ethOamServiceUnavailSec

Indicates the number of unavailable seconds since
the time the service is up.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.15

ethOamServiceUnavailRatio

Indicates the ratio of the unavailable seconds since the
time the service is up. The value is the ratio multiplied by 1E10.
0xFFFFFFFF will be returned for ratio greater than 4/10 (40%).

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.16

ethOamServiceFramesAboveDelay

Indicates the number of frames arrived with delay
greater than the delay threshold.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.17

ethOamServiceOverflowFramesAboveDelay

Indicates the number of times the associated
ethOamServiceFramesAboveDelay counter has overflowed.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.18

ethOamServiceFramesAboveDelayVar

Indicates the number of frames arrived with delay variation
greater than the delay variation threshold.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.19

ethOamServiceOverflowFramesAboveDelayVar

Indicates the number of times the associated
ethOamServiceFramesAboveDelayVar counter has overflowed.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.20

ethOamServiceCurrentDelay

Indicates the last measured delay sample in msec.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.21

ethOamServiceCurrentDelayVariation

Indicates the last measured delay variation sample in msec.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.22

ethOamServiceResetCounters

Reset the running PM counters of the selected service.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.1.3.2.1.1.23

ethOamSvcCurrentStatTable

table

.1.3.6.1.4.1.164.3.1.6.1.3.2.2 · 1 row entry · 13 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ethOamSvcCurrentStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ethOamSvcCurrentStatTable'

Service Current Statistics Table.

ethOamSvcCurrentStatEntry row .1.3.6.1.4.1.164.3.1.6.1.3.2.2.1

Current Statistics per service

Indexes

No indexes recorded

Column Syntax OID

ethOamSvcCurrFramesAboveDelayThresh

Number of frames that arrived in the current interval
at a delay greater than the threshold value defined for the service.

PerfHist-TC-MIBPerfCurrentCount

Constraints:
range: 1-43

.1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.1

ethOamSvcCurrFramesBelowDelayThresh

Number of frames that arrived in the current interval at a delay
lower than or equal to the threshold value defined for the service.

PerfHist-TC-MIBPerfCurrentCount

.1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.2

ethOamSvcCurrFramesAboveDVarThresh

Number of frames that arrived in the current interval at a delay
variation greater than the threshold value defined for the service.

PerfHist-TC-MIBPerfCurrentCount

.1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.3

ethOamSvcCurrFramesBelowDVarThresh

Number of frames that arrived in the current interval
at a delay variation lower than or equal to the
threshold value defined for the service.

PerfHist-TC-MIBPerfCurrentCount

.1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.4

ethOamSvcCurrFramesTxCounter

Number of trnasmitted frames in the current interval.

PerfHist-TC-MIBPerfCurrentCount

.1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.5

ethOamSvcCurrFramesLossCounter

Number of lost frames in the current interval.

PerfHist-TC-MIBPerfCurrentCount

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.6

ethOamSvcCurrMinRoundTripDelay

The mininal value of round trip delay in the current interval.
Values units are of 0.1 msec.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.7

ethOamSvcCurrMaxRoundTripDelay

The maximum value of round trip delay in the current interval.
Values units are of 0.1 msec.

SNMPv2-SMIUnsigned32

Enumerated Values:

1	rlyHit
2	rlyFdb
3	rlyMpdb

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.8

ethOamSvcCurrAvgRoundTripDelay

The average round trip delay in the current interval.
Values units are of 0.1 msec.

SNMPv2-SMIUnsigned32

Enumerated Values:

1	ingNoTlv
2	ingOk
3	ingDown
4	ingBlocked
5	ingVid

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.9

ethOamSvcCurrMaxRoundTripDVar

The maximum value of round trip delay variation in the current interval.
Values units are of 0.1 msec.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.10

ethOamSvcCurrAvgRoundTripDVar

The average round trip delay variation in the current interval.
Values units are of 0.1 msec.

SNMPv2-SMIUnsigned32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.11

ethOamSvcCurrElapsedTime

The number of seconds that have elapsed since
the beginning of the current interval.

Integer32

Enumerated Values:

1	egrNoTlv
2	egrOK
3	egrDown
4	egrBlocked
5	egrVid

.1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.12

ethOamSvcCurrUnavailSec

The number of seconds that the service was unavailable in the current interval.

PerfHist-TC-MIBPerfCurrentCount

.1.3.6.1.4.1.164.3.1.6.1.3.2.2.1.13

ethOamSvcIntervalTable

table

.1.3.6.1.4.1.164.3.1.6.1.3.2.3 · 1 row entry · 13 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ethOamSvcIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ethOamSvcIntervalTable'

Service Interval Statistics Table.

ethOamSvcIntervalEntry row .1.3.6.1.4.1.164.3.1.6.1.3.2.3.1

Interval Statistics per service

Indexes

No indexes recorded

Column Syntax OID

ethOamSvcIntervalNum

The Interval index, which is actualy the Interval number,
where 1 is the most recently completed 15 minute interval,
and 96 is the least recently completed 15 minutes interval
(assuming that all 96 intervals exist).

Integer32

.1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.1

ethOamSvcIntervalFramesAboveDelayThresh

Number of frames that arrived in a delay greater than the
threshold value defined for the service in the selected interval.

PerfHist-TC-MIBPerfIntervalCount

.1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.2

ethOamSvcIntervalFramesBelowDelayThresh

Number of frames that arrived in a delay lower than the
threshold value defined for the service in the selected interval.

PerfHist-TC-MIBPerfIntervalCount

.1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.3

ethOamSvcIntervalFramesAboveDVarThresh

Number of frames that arrived in a delay variation greater than the
threshold value defined for the service in the selected interval.

PerfHist-TC-MIBPerfIntervalCount

Enumerated Values:

1	notApplicable
2	fail
3	ok
4	mismerge
5	unexpectedMep
6	unexpectedMeLevel
7	unexpectedPeriod
8	rdi

.1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.4

ethOamSvcIntervalFramesBelowDVarThresh

Number of frames that arrived in a delay variation lower than the
threshold value defined for the service in the selected interval.

PerfHist-TC-MIBPerfIntervalCount

.1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.5

ethOamSvcIntervalFramesTxCounter

Number of trnasmitted frames in the selected interval.

PerfHist-TC-MIBPerfIntervalCount

.1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.6

ethOamSvcIntervalFramesLossCounter

Number of lost frames in the selected interval.

PerfHist-TC-MIBPerfIntervalCount

.1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.7

ethOamSvcIntervalMinRoundTripDelay

The mininal value of round trip delay in the selected interval.
Values units are of 0.1 msec.

SNMPv2-SMIUnsigned32

Enumerated Values:

1	preStandard
2	standard

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.8

ethOamSvcIntervalMaxRoundTripDelay

The maximum value of round trip delay in the selected interval.
Values units are of 0.1 msec.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.9

ethOamSvcIntervalAvgRoundTripDelay

The average round trip delay in the selected interval.
Values units are of 0.1 msec.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.10

ethOamSvcIntervalMaxRoundTripDVar

The maximum value of round trip delay variation in the selected interval.
Values units are of 0.1 msec.

SNMPv2-SMIUnsigned32

Enumerated Values:

2	disabled
3	ccBased
4	lbBased

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.11

ethOamSvcIntervalAvgRoundTripDVar

The average round trip delay variation in the selected interval.
Values units are of 0.1 msec.

SNMPv2-SMIUnsigned32

Enumerated Values:

1	unicast
2	multicast

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.12

ethOamSvcIntervalUnavailSec

The number of seconds that the service was unavailable
in the selected interval.

PerfHist-TC-MIBPerfIntervalCount

.1.3.6.1.4.1.164.3.1.6.1.3.2.3.1.13

ethOamSvcTotalTable

table

.1.3.6.1.4.1.164.3.1.6.1.3.2.4 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ethOamSvcTotalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ethOamSvcTotalTable'

ETH OAM Service Total (24H) Statistics Table.

ethOamSvcTotalEntry row .1.3.6.1.4.1.164.3.1.6.1.3.2.4.1

Total Statistics per service

Indexes

No indexes recorded

Column Syntax OID

ethOamSvcTotalFramesAboveDelayThresh

Number of frames that arrived in a delay greater than the
threshold value defined for the service in the last 24H.

PerfHist-TC-MIBPerfTotalCount

.1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.1

ethOamSvcTotalFramesBelowDelayThresh

Number of frames that arrived in a delay lower than the
threshold value defined for the service in the last 24H.

PerfHist-TC-MIBPerfTotalCount

Enumerated Values:

1	notApplicable
2	fail
3	ok
4	mismerge
5	unexpectedMep
6	unexpectedMeLevel
7	unexpectedPeriod
8	rdi

.1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.2

ethOamSvcTotalFramesAboveDVarThresh

Number of frames that arrived in a delay variation greater than the
threshold value defined for the service in the last 24H.

PerfHist-TC-MIBPerfTotalCount

.1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.3

ethOamSvcTotalFramesBelowDVarThresh

Number of frames that arrived in a delay variation lower than the
threshold value defined for the service in the last 24H.

PerfHist-TC-MIBPerfTotalCount

.1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.4

ethOamSvcTotalFramesTxCounter

Number of trnasmitted frames in the last 24H.

PerfHist-TC-MIBPerfTotalCount

.1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.5

ethOamSvcTotalFramesLossCounter

Number of lost frames in the last 24H.

PerfHist-TC-MIBPerfTotalCount

Enumerated Values:

2	down
3	up

.1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.6

ethOamSvcTotalMinRoundTripDelay

The mininal value of round trip delay in the last 24H.
Values units are of 0.1 msec.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.7

ethOamSvcTotalMaxRoundTripDelay

The maximum value of round trip delay in the last 24H.
Values units are of 0.1 msec.

SNMPv2-SMIUnsigned32

Enumerated Values:

1	notApplicable
2	open
3	close

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.8

ethOamSvcTotalAvgRoundTripDelay

The average round trip delay in the last 24H.
Values units are of 0.1 msec.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.9

ethOamSvcTotalMaxRoundTripDVar

The maximum value of round trip delay variation in the last 24H.
Values units are of 0.1 msec.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.10

ethOamSvcTotalAvgRoundTripDVar

The average round trip delay variation in the last 24H.
Values units are of 0.1 msec.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.11

ethOamSvcTotalUnavailSec

The number of seconds that the service was unavailable
in the last 24H.

PerfHist-TC-MIBPerfTotalCount

.1.3.6.1.4.1.164.3.1.6.1.3.2.4.1.12

radMdTable

table

.1.3.6.1.4.1.164.3.1.6.1.3.3 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radMdTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radMdTable'

The MaintenanceDomain table. Each row in the table represents
a different maintenance domain.
          
A Maintenance domain is described in 802.1ag (3.22) as the
network or the part of the network for which faults in
connectivity are to be managed. The boundary of a Maintenance
Domain is defined by a set of DSAPs, each of which can become
a point of connectivity to a service instance.

radMdEntry row .1.3.6.1.4.1.164.3.1.6.1.3.3.1

The Maintenance Domain table entry. This entry is not lost
upon reboot. It is backed up by stable storage

Indexes

No indexes recorded

Column Syntax OID

radMdIndex

The index to the maintenance domain table.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.3.1.1

radMdFormat

The type (and thereby format) of the Maintenance Domain Name.

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.6.1.3.3.1.2

radMdName

The Maintenance Domain name. The type/format of this object
is determined by the value of the radMdNameType object.

Each Maintenance Domain has unique name amongst all those
used or available to a servi…

OctetStringr/w

.1.3.6.1.4.1.164.3.1.6.1.3.3.1.3

radMdRowStatus

This attribute allows to create/delete a row in this table.

The writable columns in a row can not be changed if the row
is active. All columns must have a valid value before a row
can be activated.

SNMPv2-TCRowStatusr/w

Enumerated Values:

1	all
2	ingress
3	egress

Description:

.1.3.6.1.4.1.164.3.1.6.1.3.3.1.4

radMepLtrTable

table

.1.3.6.1.4.1.164.3.1.6.1.3.4 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radMepLtrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radMepLtrTable'

This table contains a list of Linktrace replies 
received by a specific MEP in response to
a linktrace message.

radMepLtrEntry row .1.3.6.1.4.1.164.3.1.6.1.3.4.1

The LinktraceReply table entry.

Indexes

No indexes recorded

Column Syntax OID

radMepLtrReceiveOrder

An index to distinguish among multiple LTRs with the same LTR
Transaction Identifier field value. radMepLtrReceiveOrder
are assigned sequentially from 1, in the order that the
Linktrace Initiator received the LTRs.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.4.1.1

radMepLtrTtl

TTL field value for a returned LTR.

Unsigned32

.1.3.6.1.4.1.164.3.1.6.1.3.4.1.2

radMepLtrMacAddr

The MAC address in the header of the returned LTR.

MacAddress

Type Constraints:
range: 6

.1.3.6.1.4.1.164.3.1.6.1.3.4.1.3

radMepLtrRelay

The value returned in the Relay Action field:
rlyHit - the LTM reached an MP whose MAC address matches the target MAC address.
rlyFdb - the Egress Port was determined by consulting the Filtering Database.
rlyMpdb - the …

Enumeration

Constraints:
range: 1-4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.4.1.4

radMepLtrIngress

The value returned in the Ingress Action Field of the LTM.
ingNoTlv - no Reply Ingress TLV was returned in the LTM.
ingOK - the target data frame would be passed through to the MAC Relay Entity.
ingDown - the Bridge Por…

Enumeration

.1.3.6.1.4.1.164.3.1.6.1.3.4.1.5

radMepLtrIngressPortIdSubtype

The format of the Ingress Port ID.
If the radMepLtrIngress object contains the value
egrNoTlv(1), then the contents of this object are meaningless.
802.1ag clauses 12.14.7.5.3:m and 20.36.2.8

LLDP-MIBLldpPortIdSubtype

Enumerated Values:

1	passive
2	active

.1.3.6.1.4.1.164.3.1.6.1.3.4.1.6

radMepLtrIngressPortId

Ingress Port ID. This is an alpha-numeric string that contains a
specific identifier for the port.
The format of this object is determined by
the value of the radMepLtrIngressPortIdSubtype object.
If the radMepLtrIngr…

OctetString

Enumerated Values:

1	ignore
2	process

.1.3.6.1.4.1.164.3.1.6.1.3.4.1.7

radMepLtrEgress

The value returned in the Egress Action Field of the LTM.
The value egrNoTlv(1) indicates that no Reply Egress TLV was
returned in the LTM.
802.1ag clauses 12.14.7.5.3:o and 20.36.2.10

Enumeration

.1.3.6.1.4.1.164.3.1.6.1.3.4.1.8

radMepLtrEgressPortIdSubtype

The format of the egress Port ID.
If the radMepLtrEgress object contains the value
egrNoTlv(1), then the contents of this object are meaningless.
802.1ag clauses 12.14.7.5.3:q and 20.36.2.12

LLDP-MIBLldpPortIdSubtype

Type Values:

1	interfaceAlias
2	portComponent
3	macAddress
4	networkAddress
5	interfaceName
6	agentCircuitId
7	local

.1.3.6.1.4.1.164.3.1.6.1.3.4.1.9

radMepLtrEgressPortId

Egress Port ID. The format of this object is determined by
the value of the radMepLtrEgressPortIdSubtype object.
If the radMepLtrEgress object contains the value
egrNoTlv(1), then the contents of this object are meaning…

OctetString

.1.3.6.1.4.1.164.3.1.6.1.3.4.1.10

radMepCcStatusTable

table

.1.3.6.1.4.1.164.3.1.6.1.3.5 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radMepCcStatusTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radMepCcStatusTable'

This table contains a list of CC Status  
received by a specific MEP from different Remote MEPs.

radMepCcStatusEntry row .1.3.6.1.4.1.164.3.1.6.1.3.5.1

An entry in the CC Status Table.

Indexes

No indexes recorded

Column	Syntax	OID
radMepRemoteMepIdx This is a running index for arriving CC messages (from different Remote MEPs) for a specific MEP ID.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.3.5.1.1`
radMepCcStatusRemMepId This attribute indicates the Remote MEP ID from which the CC messages has arrived.	SNMPv2-SMIUnsigned32r/w Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.3.5.1.2`
radMepCcStat This object indicates the Continuity Check (CC) status (ITU-T Y.1731, Appendix I): mismerge - A MEP detects a Mismerge condition when a CCM frame arrives with the correct MEG level, but incorrect MEG ID. unexpected…	Enumeration	`.1.3.6.1.4.1.164.3.1.6.1.3.5.1.3`
radMepCcStatusMacAddr This object indicates the MAC Address in the CC Status message received.	MacAddress Type Constraints: `range: 6`	`.1.3.6.1.4.1.164.3.1.6.1.3.5.1.4`

dot1agXCfmMdTable

table

.1.3.6.1.4.1.164.3.1.6.1.3.8 · 1 row entry · 1 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk dot1agXCfmMdTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::dot1agXCfmMdTable'

The Maintenance Domain table. Each row in the table represents
a different maintenance association.

dot1agXCfmMdEntry row .1.3.6.1.4.1.164.3.1.6.1.3.8.1

The Maintenance Domain table entry.

Indexes

No indexes recorded

Column	Syntax	OID
dot1agXCfmMdProtocol .	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.3.8.1.1`

dot1agXCfmMepTable

table

.1.3.6.1.4.1.164.3.1.6.1.3.9 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk dot1agXCfmMepTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::dot1agXCfmMepTable'

The Maintenance Association End Point (MEP) table.

dot1agXCfmMepEntry row .1.3.6.1.4.1.164.3.1.6.1.3.9.1

The MEP table entry

Indexes

No indexes recorded

Column Syntax OID

dot1agXCfmMepContinuityVerMode

This object determines the OAM behavior of the MEP:
disabled - no Continuity Verification is done
cc_based - Continuity Verification is done based on incoming CC messages
lb_based - Continuity Verification is done base…

Enumerationr/w

Enumerated Values:

2	unlock
3	lock

.1.3.6.1.4.1.164.3.1.6.1.3.9.1.1

dot1agXCfmMepDestAddrType

This object determines if the OAM messages are sent to user defined
unicast address, or to RAD proprietary multicast address.

Enumerationr/w

Enumerated Values:

2	drop
3	dropNotify
4	shutdown

.1.3.6.1.4.1.164.3.1.6.1.3.9.1.2

dot1agXCfmMepDestMacAddr

This object determines the MAC address that OAM packets are sent to.

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.3.1.6.1.3.9.1.3

dot1agXCfmMepMappingProfile

This attribute defines the Mapping/classification profile (flowMappingProfileTable )
assigned to this Mep.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

2	shutdown
3	secureActive
4	secureInactive

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.3.9.1.4

dot1agXCfmMepDbTable

table

.1.3.6.1.4.1.164.3.1.6.1.3.10 · 1 row entry · 1 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk dot1agXCfmMepDbTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::dot1agXCfmMepDbTable'

The MEP DB table

dot1agXCfmMepDbEntry row .1.3.6.1.4.1.164.3.1.6.1.3.10.1

The MEP Database table entry.

Indexes

ethIfSrcMacCtrlAddrIndex ethIfSrcMacCtrlAddr ethIfSrcMacCtrlAddrIdx3

Column	Syntax	OID
dot1agXCfmMepCcStat This object indicates the Continuity Check (CC) status (ITU-T Y.1731, Appendix I): mismerge - A MEP detects a Mismerge condition when a CCM frame arrives with the correct MEG level, but incorrect MEG ID. unexpected…	Enumeration	`.1.3.6.1.4.1.164.3.1.6.1.3.10.1.1`

ethIfRingTable

table

.1.3.6.1.4.1.164.3.1.6.1.4.1 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ethIfRingTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ethIfRingTable'

Ethernet Ring Table.

ethIfRingEntry row .1.3.6.1.4.1.164.3.1.6.1.4.1.1

An entry in the table.

Indexes

No indexes recorded

Column Syntax OID

ethIfRingIdx

This object is an Index that can indicate
Slot, Ring, Cnfg etc., according to the device used.
When NA, 1 will be used.

SNMPv2-SMIUnsigned32

Enumerated Values:

1	active
4	createAndGo
6	destroy

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.4.1.1.1

ethIfRingAdminStatus

This object denotes the Ethernet Ring administrative status.

Enumerationr/w

Enumerated Values:

2	invalid
3	learned
5	mgmt

.1.3.6.1.4.1.164.3.1.6.1.4.1.1.2

ethIfRingPorts

The set of ports which are assigned to be ring members.
The default value of this object is a string of zeros.

Q-BRIDGE-MIBPortListr/w

.1.3.6.1.4.1.164.3.1.6.1.4.1.1.3

ethIfRingOperStatus

This object indicates the Ethernet Ring operational status.

Enumeration

.1.3.6.1.4.1.164.3.1.6.1.4.1.1.4

ethIfRingKeepAliveInterval

This parameter indicates the period of time (in msec.)
between two consequent Keep Alive messages.

SNMPv2-SMIUnsigned32r/w

Constraints:
range: 0-899

.1.3.6.1.4.1.164.3.1.6.1.4.1.1.5

ethIfRingKeepAliveThresh

This parameter indicates the maximum number of
missed Keep Alive answer messages acceptable, after which link status will be failed.

SNMPv2-SMIUnsigned32r/w

Constraints:
range: 0-96

.1.3.6.1.4.1.164.3.1.6.1.4.1.1.6

ethIfRingKeepAliveVlanId

Dedicated VLAN ID for keep alive messages.

SNMPv2-SMIUnsigned32r/w

Constraints:
range: 1-1

.1.3.6.1.4.1.164.3.1.6.1.4.1.1.7

ethIfRingMultiCastVlanId

Dedicated VLAN ID for multicast messages.

SNMPv2-SMIUnsigned32r/w

Constraints:
range: 1-1

.1.3.6.1.4.1.164.3.1.6.1.4.1.1.8

ethIfRingRowStatus

Implement creation/deletion of rings in the device.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.1.4.1.1.9

ethIfStormTable

table

.1.3.6.1.4.1.164.3.1.6.1.5.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ethIfStormTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ethIfStormTable'

Ethernet Storming Table.

ethIfStormEntry row .1.3.6.1.4.1.164.3.1.6.1.5.1.1

An entry in the table.

Indexes

No indexes recorded

Column	Syntax	OID
ethIfStormCnfgIdx This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.	Unsigned32	`.1.3.6.1.4.1.164.3.1.6.1.5.1.1.1`
ethIfStormIfIdx A unique index of the ethernet interface/port.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.5.1.1.2`
ethIfStormDirection This object indicates the port's Storm Direction.	Enumeration	`.1.3.6.1.4.1.164.3.1.6.1.5.1.1.3`
ethIfStormPacketType Packet Type on which Storming operations will be performed.	Bits	`.1.3.6.1.4.1.164.3.1.6.1.5.1.1.4`
ethIfStormCtrlEnable This object indicates if the Storm Controling is Enabled or Disabled for the relevant entry.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.5.1.1.5`
ethIfStormMaxRate This object indicates the Maximum Rate at which Storming packets are forwarded, in Kbps.For some devices the units are PPS(Packets Per Second ) or kilobytes per second.	SNMPv2-SMIUnsigned32r/w Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.5.1.1.6`

dot3OamDescrTable

table

.1.3.6.1.4.1.164.3.1.6.1.6.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk dot3OamDescrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::dot3OamDescrTable'

This table supports definitions of Descriptors (profiles) of OAM EFM Links.

dot3OamDescrEntry row .1.3.6.1.4.1.164.3.1.6.1.6.1.1

Each entry corresponds to a single OAM EFM Descriptor (profile).
Each Descriptor contains a set of OAM EFM Link configuration
parameters. The configuration parameters are applied to the
OAM EFM Links referencing thi…

Indexes

No indexes recorded

Column Syntax OID

dot3OamDescrId

This object is the unique index associated with this Descriptor (profile).
Entries in this table are referenced via the object dot3OamXDescrId
in dot3OamXEntry.

Unsigned32

.1.3.6.1.4.1.164.3.1.6.1.6.1.1.1

dot3OamDescrRowStatus

This object controls creation/deletion of the associated entry in this table
per the semantics of RowStatus. If an active entry is referenced in
dot3OamXDescrId, the entry MUST remain active until all references are …

SNMPv2-TCRowStatusr/w

Constraints:
range: 4-4

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.3.1.6.1.6.1.1.2

dot3OamDescrMode

This object controls the mode of OAM operation for an Ethernet-like interface
referencing this Descriptor.
OAM on Ethernet interfaces may be in 'active' mode or 'passive' mode.
These two modes differ in that active …

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.1.6.1.1.3

dot3OamDescrLbRxOperation

Since OAM loopback is a disruptive operation (user traffic does not pass),
this object provides a mechanism to provide control: whether received OAM
loopback commands are processed or ignored, for the OAM Link referen…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.1.6.1.1.4

dot3OamDescrRateLimit

This object defines how many OAM frames can be sent per second (maximum)
for an OAM EFM Link referencing this Descriptor.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.1.6.1.1.5

dot3OamXTable

table

.1.3.6.1.4.1.164.3.1.6.1.6.2 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk dot3OamXTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::dot3OamXTable'

This table is an extension of dot3OamTable of standard DOT3-OAM-MIB.

dot3OamXEntry row .1.3.6.1.4.1.164.3.1.6.1.6.2.1

An entry in dot3OamXTable.

Indexes

IF-MIBifIndex prtSonetLineIntervalNumber

Column	Syntax	OID
dot3OamXDescrId This object points to an entry of dot3OamDescrTable (dot3OamDescrId), which defines part of the configuration parameters for this OAM EFM Link. As long as one of the OAM EFM Links refers an entry in the dot3OamDescrTab…	Unsigned32r/w Constraints: `range: 1-96`	`.1.3.6.1.4.1.164.3.1.6.1.6.2.1.1`
dot3OamXPeerState This object reports the state of the Peer of the OAM EFM Link. unknown - at the initialization of the device, or after Reset, when there is still no data about the peer's state. operational - usually after u…	Enumeration	`.1.3.6.1.4.1.164.3.1.6.1.6.2.1.2`

ethIfSrcMacCtrlTable

table

.1.3.6.1.4.1.164.3.1.6.1.7.1 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ethIfSrcMacCtrlTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ethIfSrcMacCtrlTable'

This table supports source MAC addresses control parameters per interface.
Source MAC control will be used mainly for security. Only packets with certain source MAC
Addresses will be allowed to access the device. The source MAC addresses can be static or learned.
The static addresses will be defined by the user in another table: ethIfSrcMacCtrlAddrTable.
The learned addresses will exist in the ethIfSrcMacCtrlAddrTable as well.

ethIfSrcMacCtrlEntry row .1.3.6.1.4.1.164.3.1.6.1.7.1.1

An entry in the table.

Indexes

No indexes recorded

Column	Syntax	OID
ethIfSrcMacCtrlIndex The index of the MAC Layer interface supporting source MAC control feature. It may be the ifIndex of the ETH/Bridge Port.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.7.1.1.1`
ethIfSrcMacCtrlIdx2 A second index that can be used. For example: The VLAN ID for which the source MAC control feature is supported. When this index is not in use, its value will be: 9999.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.7.1.1.2`
ethIfSrcMacCtrl Enable or disable the source MAC control on the current interface. The device should not enable source MAC control if for the current interface there are more than ethIfSrcMacCtrlMaxPermitAddr addresses in the ethIfSrcM…	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.7.1.1.3`
ethIfSrcMacCtrlMaxPermitAddr This is the maximum number of permitted MAC addresses (static and learned) for the current interface.	SNMPv2-SMIUnsigned32r/w Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.7.1.1.4`
ethIfSrcMacCtrlCurNumPermitAddr This is the number of source MAC addresses currently permitted for the current interface.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.7.1.1.5`
ethIfSrcMacCtrlFlushAddrCmd When set to on (3) this command will erase all the learned addresses and invalid addresses of the selected interface in the ethIfSrcMacCtrlAddrTable. After operation is finished, Agent will turn the value to 'off'.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.7.1.1.6`
ethIfSrcMacCtrlAging The timeout period in seconds for aging out dynamically learned source MAC addresses. Valid Values: 0 - disable 10-1000000	SNMPv2-SMIUnsigned32r/w Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.7.1.1.7`
ethIfSrcMacCtrlLocking When set to lock (3) this command will lock the Source MAC Address learning. No more learned addresses will be added to the ethIfSrcMacCtrlAddrTable. When set to unlock (2) this command will unlock the Source MAC Addres…	Enumerationr/w Constraints: `range: 4-4`	`.1.3.6.1.4.1.164.3.1.6.1.7.1.1.8`
ethIfSrcMacCtrlViolationAction Determines the action that the device will take upon security violation. drop(2) - the violating packets will be dropped. dropNotify (3)- the violating packets will be dropped and notifications …	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.7.1.1.9`
ethIfSrcMacCtrlLastViolatingAddr This object indicates the last MAC address that violated the security on the current interface. If no violation, the agent will return: 00-00-00-00-00-00 .	MacAddressr/w Type Constraints: `range: 6`	`.1.3.6.1.4.1.164.3.1.6.1.7.1.1.10`
ethIfSrcMacCtrlPortStatus This object represents the operational status of the MAC Control feature on an interface. shutdown(2) - This indicates that the port is shutdown due to security violation. secureActive (3) - T…	Enumeration	`.1.3.6.1.4.1.164.3.1.6.1.7.1.1.11`

ethIfSrcMacCtrlAddrTable

table

.1.3.6.1.4.1.164.3.1.6.1.7.2 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ethIfSrcMacCtrlAddrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ethIfSrcMacCtrlAddrTable'

This table shows which MAC Addresses are permitted when the source MAC control
is enabled and which non permitted MAC Addresses attempted to access the
current interface. It contains static source MAC Addresses as well as learned
MAC Addresses. The user can configure Static permitted source MAC Addresses via this table.

ethIfSrcMacCtrlAddrEntry row .1.3.6.1.4.1.164.3.1.6.1.7.2.1

An entry in the table.

Indexes

No indexes recorded

Column	Syntax	OID
ethIfSrcMacCtrlAddrIndex The index of the interface for which the source MAC addresses exist in this table. It may be the ifIndex of the ETH/Bridge Port.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.7.2.1.1`
ethIfSrcMacCtrlAddr A unicast source MAC address that was learned or statically configured for the current interface. Packets with this source MAC address will be accepted by the device.	MacAddress Type Constraints: `range: 6`	`.1.3.6.1.4.1.164.3.1.6.1.7.2.1.2`
ethIfSrcMacCtrlAddrIdx3 A third index that can be used. For example: The VLAN ID for which the source MAC control feature is supported. When this index is not in use, its value will be: 9999.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.1.7.2.1.3`
ethIfSrcMacCtrlAddrRowStatus This MIB object will be used in order to create/delete a static row or delete an address that is not allowed to access the current interface (ethIfSrcMacCtrlAddrStatus= invalid(2)). Device will add the learned address…	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.1.7.2.1.4`
ethIfSrcMacCtrlAddrStatus The status of this entry. The meanings of the values are: invalid (2) - the current address is not allowed to access this interface. learned(3) - the current address was learned. mgmt (5) - the current addres…	Enumeration	`.1.3.6.1.4.1.164.3.1.6.1.7.2.1.5`

prtSonetMediumTable

table

.1.3.6.1.4.1.164.3.1.6.2.1.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtSonetMediumTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtSonetMediumTable'

The SONET Medium table.

prtSonetMediumEntry row .1.3.6.1.4.1.164.3.1.6.2.1.1.1

An entry in the SONET Medium table. ifIndex of the
lowest SONET layer of type sonet(39).

Indexes

No indexes recorded

Column	Syntax	OID
prtSonetMediumTimeElapsed The number of seconds that have elapsed since the beginning of the near end current error- measurement period.	Integer32	`.1.3.6.1.4.1.164.3.1.6.2.1.1.1.1`
prtSonetMediumValidIntervals The number of previous near end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complet…	Integer32	`.1.3.6.1.4.1.164.3.1.6.2.1.1.1.2`
prtSonetMediumSsmRX This parameter indicates SSM RX value (quality level of clock signal). SSM (Synchronization Status Messages) octet is encoded as follows: Bit1 = '1' - indicates all octet is Not Applicable Bits 8-5 (when bit1=0): …	OctetString	`.1.3.6.1.4.1.164.3.1.6.2.1.1.1.3`
prtSonetMediumSsmTX This parameter indicates SSM TX value (quality level of clock signal). SSM (Synchronization Status Messages) octet is encoded the same as prtSonetMediumSsmRX.	OctetString Constraints: `range: 1-96`	`.1.3.6.1.4.1.164.3.1.6.2.1.1.1.4`

prtSonetSectionLineCurrentTable

table

.1.3.6.1.4.1.164.3.1.6.2.1.2 · 1 row entry · 14 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtSonetSectionLineCurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtSonetSectionLineCurrentTable'

The SONET Section/Line Current table.

prtSectionLineCurrentEntry row .1.3.6.1.4.1.164.3.1.6.2.1.2.1

An entry in the SONET Section/Line Current table.
ifIndex of the section/line SONET layer of type
sonet(39).

Indexes

No indexes recorded

Column	Syntax	OID
prtSonetCurrentLOS The counter associated with the number of LOS seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.2.1.1`
prtSonetCurrentLOF The counter associated with the number of LOF seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.2.1.2`
prtSonetCurrentLineAIS The counter associated with the number of Line AIS seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.2.1.3`
prtSonetCurrentLineFERF The counter associated with the number of Line FERF seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.2.1.4`
prtSonetCurrentSectionBIP The counter associated with the number of Section BIP errors, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.2.1.5`
prtSonetCurrentLineBIP The counter associated with the number of Line BIP errors, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.2.1.6`
prtSonetCurrentLineFEBE The counter associated with the number of Line FEBE errors, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.2.1.7`
prtSonetCurrentUAS The counter associated with the number of UAS encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.2.1.8`
prtSonetCurrentSES The counter associated with the number of SES encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Constraints: `range: 1-63`	`.1.3.6.1.4.1.164.3.1.6.2.1.2.1.9`
prtSonetCurrentES The number of Errored Seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Constraints: `range: 1-63`	`.1.3.6.1.4.1.164.3.1.6.2.1.2.1.10`
prtSonetCurrentStatus The statuses of the current interval: 0 - O.K. 1 - The link has been switched by a redundancy mechanism. 2 - Module is in/out. 4 - Empty - card is out.	OctetString	`.1.3.6.1.4.1.164.3.1.6.2.1.2.1.11`
prtSonetCurrentLSV The counter associated with the number of LSV seconds (Line Symbol Violation), encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.2.1.12`
prtSonetCurrentXStatus This variable indicates the Status of the interface. It contains failure state information. The variable is a bit map represented as a sum, therefore, it can represent multiple failures simultaneously. The sonetSe…	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.6.2.1.2.1.13`
prtSonetCurrentLineRDI The counter associated with the number of Line RDI seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.2.1.14`

prtSonetSectionLineIntervalTable

table

.1.3.6.1.4.1.164.3.1.6.2.1.3 · 1 row entry · 14 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtSonetSectionLineIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtSonetSectionLineIntervalTable'

The Section/Line Interval table.

prtSectionLineIntervalEntry row .1.3.6.1.4.1.164.3.1.6.2.1.3.1

An entry in the SONET Section/Line Interval table.
ifIndex of the section/line SONET layer of type
sonet(39).

Indexes

No indexes recorded

Column	Syntax	OID
prtSonetLineIntervalNumber A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).	Integer32	`.1.3.6.1.4.1.164.3.1.6.2.1.3.1.1`
prtSonetIntervalLOS The counter associated with the number of LOS seconds , encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.3.1.2`
prtSonetIntervalLOF The counter associated with the number of LOF seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.3.1.3`
prtSonetIntervalLineAIS The counter associated with the number of Line AIS seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.3.1.4`
prtSonetIntervalLineFERF The counter associated with the number of Line FERF seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Constraints: `range: 1-64`	`.1.3.6.1.4.1.164.3.1.6.2.1.3.1.5`
prtSonetIntervalSectionBIP The counter associated with the number of Section BIP errors, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.3.1.6`
prtSonetIntervalLineBIP The counter associated with the number of Line BIP errors, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.3.1.7`
prtSonetIntervalLineFEBE The counter associated with the number of Line FEBE errors, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Constraints: `range: 1-96`	`.1.3.6.1.4.1.164.3.1.6.2.1.3.1.8`
prtSonetIntervalUAS The counter associated with the number of UAS encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Constraints: `range: 1-64`	`.1.3.6.1.4.1.164.3.1.6.2.1.3.1.9`
prtSonetIntervalSES The counter associated with the number of SES encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Constraints: `range: 1-64`	`.1.3.6.1.4.1.164.3.1.6.2.1.3.1.10`
prtSonetIntervalES The number of Errored Seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.3.1.11`
prtSonetIntervalStatus The statuses of the current interval: 0 - O.K. 1 - The link has been switched by a redundancy mechanism. 2 - Module is in/out. 4 - Empty - card is out.	OctetString	`.1.3.6.1.4.1.164.3.1.6.2.1.3.1.12`
prtSonetIntervalLSV The counter associated with the number of LSV seconds (Line Symbol Violation), encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.3.1.13`
prtSonetIntervalLineRDI The counter associated with the number of Line RDI seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.3.1.14`

prtSonetPathCurrentTable

table

.1.3.6.1.4.1.164.3.1.6.2.1.4 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtSonetPathCurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtSonetPathCurrentTable'

The SONET Path Current table.

prtPathCurrentEntry row .1.3.6.1.4.1.164.3.1.6.2.1.4.1

An entry in the SONET Path Current table.
ifIndex of the Path SONET layer of type
sonetPath(50).

Indexes

No indexes recorded

Column	Syntax	OID
prtSonetCurrentPathAIS The counter associated with the number of Path AIS seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.4.1.1`
prtSonetCurrentPathFERF The counter associated with the number of Path FERF seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.4.1.2`
prtSonetCurrentLOP The counter associated with the number LOP seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.4.1.3`
prtSonetCurrentSLM The counter associated with the number of SLM seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.4.1.4`
prtSonetCurrentLOC The counter associated with the number of LOC seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.4.1.5`
prtSonetCurrentPathBIP The counter associated with the number of Path BIP errors, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.4.1.6`
prtSonetCurrentPathFEBE The counter associated with the number of Path FEBE errors, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.4.1.7`
prtSonetPathCurrentStatus This variable indicates the Status of the interface. It contains failure state information. The variable is a bit map represented as a sum, therefore, it can represent multiple failures simultaneously. The sonetPa…	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.6.2.1.4.1.8`
prtSonetCurrentPathRDI The counter associated with the number of Path RDI seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.4.1.9`

prtSonetPathIntervalTable

table

.1.3.6.1.4.1.164.3.1.6.2.1.5 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtSonetPathIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtSonetPathIntervalTable'

The Path Interval table.

prtPathIntervalEntry row .1.3.6.1.4.1.164.3.1.6.2.1.5.1

An entry in the SONET Path Interval table.

Indexes

No indexes recorded

Column	Syntax	OID
prtSonetPathIntervalNumber A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).	Integer32	`.1.3.6.1.4.1.164.3.1.6.2.1.5.1.1`
prtSonetIntervalPathAIS The counter associated with the number of Path AIS seconds , encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.5.1.2`
prtSonetIntervalPathFERF The counter associated with the number of Path FERF seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.5.1.3`
prtSonetIntervalLOP The counter associated with the number of LOP seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.5.1.4`
prtSonetIntervalSLM The counter associated with the number of SLM seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.5.1.5`
prtSonetIntervalLOC The counter associated with the number of LOC seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.5.1.6`
prtSonetIntervalPathBIP The counter associated with the number of Path BIP errors, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.5.1.7`
prtSonetIntervalPathFEBE The counter associated with the number of Path FEBE errors, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.5.1.8`
prtSonetIntervalPathRDI The counter associated with the number of Path RDI seconds , encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.1.5.1.9`

virtualIfCurrentTable

table

.1.3.6.1.4.1.164.3.1.6.2.1.6.1 · 1 row entry · 13 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk virtualIfCurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::virtualIfCurrentTable'

The Virtual Interface Current table.

virtualIfCurrentEntry row .1.3.6.1.4.1.164.3.1.6.2.1.6.1.1

An entry in the Virtual Interface Current table.

Indexes

No indexes recorded

Column	Syntax	OID
virtualIfCurrentMinActiveVC This object holds the minimum number of active virtual containers (VCs) of the Virtual Concatenation Group in the current 15-minute interval.	Integer32	`.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.1`
virtualIfCurrentMaxActiveVC This object holds the maximum number of active virtual containers (VCs) of the Virtual Concatenation Group in the current 15-minute interval.	Integer32	`.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.2`
virtualIfCurrentRxFrames This counter is associated with the number of frames received from STS-3/STM-1 by a Virtual Interface in the current 15-minute interval.	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.3`
virtualIfCurrentTxFrames This counter is associated with the number of frames transmitted to STS-3/STM-1 by a Virtual Interface in the current 15-minute interval.	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.4`
virtualIfCurrentRxAbortFrames The counter associated with the number of Received Aborted frames encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	`.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.5`
virtualIfCurrentTxAbortFrames The counter associated with the number of Transmitted Aborted frames encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	`.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.6`
virtualIfCurrentMinLengthViolation This counter is associated with the number of Rx payload Min Length Violation frames encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	`.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.7`
virtualIfCurrentMaxLengthViolation This counter is associated with the number of Rx payload Max Length Violation frames encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	`.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.8`
virtualIfCurrentFcsError The counter is associated with the number of Frame Check Sequence errors encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	`.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.9`
virtualIfCurrentByteDestuffingViolation The counter associated with the number of Byte De-stuffing Violations encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	`.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.10`
virtualIfCurrentAdressMismatch The counter associated with the number of Adress Mismatch encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	`.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.11`
virtualIfCurrentControlMismatch The counter associated with the number of Control Mismatch encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	`.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.12`
virtualIfCurrentActiveVC This object holds the number of active virtual containers (VCs) of the Virtual Concatenation Group in the current 15-minute interval.	Integer32	`.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.13`

virtualIfIntervalTable

table

.1.3.6.1.4.1.164.3.1.6.2.1.6.2 · 1 row entry · 14 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk virtualIfIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::virtualIfIntervalTable'

The Virtual Interface Interval table.

virtualIfIntervalEntry row .1.3.6.1.4.1.164.3.1.6.2.1.6.2.1

An entry in the Virtual Interface Interval table.

Indexes

No indexes recorded

Column	Syntax	OID
virtualIfIntervalNumber A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is …	Integer32	`.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.1`
virtualIfIntervalMinActiveVC This object holds the minimum number of active virtual containers (VCs) of the Virtual Concatenation Group, in a particular 15-minute interval in the past 24 hours.	Integer32	`.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.2`
virtualIfIntervalMaxActiveVC This object holds the maximum number of active virtual containers (VCs) of the Virtual Concatenation Group, in a particular 15-minute interval in the past 24 hours.	Integer32	`.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.3`
virtualIfIntervalRxFrames This counter is associated with the number of frames received from STS-3/STM-1 by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.4`
virtualIfIntervalTxFrames This counter is associated with the number of frames transmitted to STS-3/STM-1 by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.5`
virtualIfIntervalRxAbortFrames This counter is associated with the number of Received Abort frames encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount	`.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.6`
virtualIfIntervalTxAbortFrames This counter is associated with the number of Transmitted Abort frames encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount	`.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.7`
virtualIfIntervalMinLengthViolation This counter is associated with the number of Rx payload Min Length Violation frames encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount	`.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.8`
virtualIfIntervalMaxLengthViolation This counter is associated with the number of Rx payload Max Length Violation frames encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount	`.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.9`
virtualIfIntervalFcsError This counter is associated with the number of Frame Check Sequence errors encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount	`.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.10`
virtualIfIntervalByteDestuffingViolation This counter is associated with the number of Byte De-stuffing Violations encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount	`.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.11`
virtualIfIntervalAdressMismatch This counter is associated with the number of Address Mismatch encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount	`.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.12`
virtualIfIntervalControlMismatch This counter is associated with the number of Control mismatch encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount	`.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.13`
virtualIfIntervalBelowMinThreshold This counter is associated with the number of seconds that number of active VCs was below minimum threshold defined by vcGroupCnfgNoOfVCs, encountered by Virtual Interface in a particular 15-minute interval in the …	PerfHist-TC-MIBPerfIntervalCount	`.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.14`

virtualIfLAPSCurrentTable

table

.1.3.6.1.4.1.164.3.1.6.2.1.6.3 · 1 row entry · 1 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk virtualIfLAPSCurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::virtualIfLAPSCurrentTable'

The Virtual Interface LAPS Current table.

virtualIfLAPSCurrentEntry row .1.3.6.1.4.1.164.3.1.6.2.1.6.3.1

An entry in the Virtual Interface
LAPS Current table.

Indexes

prtSonetGenCnfgIdx prtSonetGenIdx

Column	Syntax	OID
virtualIfLAPSCurrentSapiMismatch This counter is associated with the number of received SAPI field mismatch encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount Constraints: `range: 1-255`	`.1.3.6.1.4.1.164.3.1.6.2.1.6.3.1.1`

virtualIfLAPSIntervalTable

table

.1.3.6.1.4.1.164.3.1.6.2.1.6.4 · 1 row entry · 1 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk virtualIfLAPSIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::virtualIfLAPSIntervalTable'

The Virtual Interface LAPS table.

virtualIfLAPSIntervalEntry row .1.3.6.1.4.1.164.3.1.6.2.1.6.4.1

An entry in the Virtual Interface
LAPS Interval table.

Indexes

No indexes recorded

Column Syntax OID

virtualIfLAPSIntervalSapiMismatch

This counter is associated with the number of
received SAPI field mismatch
encountered by a Virtual Interface in a
particular 15-minute interval in the past 24 hours.

PerfHist-TC-MIBPerfIntervalCount

Enumerated Values:

1	notApplicable
3	n3
4	n4
5	n5
6	n6
7	n7
8	n8
9	n9

.1.3.6.1.4.1.164.3.1.6.2.1.6.4.1.1

virtualIfLAPFCurrentTable

table

.1.3.6.1.4.1.164.3.1.6.2.1.6.5 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk virtualIfLAPFCurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::virtualIfLAPFCurrentTable'

The Virtual Interface LAPF Current table.

virtualIfLAPFCurrentEntry row .1.3.6.1.4.1.164.3.1.6.2.1.6.5.1

An entry in the Virtual Interface
LAPF Current table.

Indexes

No indexes recorded

Column Syntax OID

virtualIfLAPFCurrentNlpidMismatch

This counter is associated with the number of
received NLPID field mismatch
encountered by a Virtual Interface
in the current 15-minute interval.

PerfHist-TC-MIBPerfCurrentCount

.1.3.6.1.4.1.164.3.1.6.2.1.6.5.1.1

virtualIfLAPFCurrentOuiMismatch

This counter is associated with the number of
received OUI field mismatch
encountered by a Virtual Interface
in the current 15-minute interval.

PerfHist-TC-MIBPerfCurrentCount

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.6.2.1.6.5.1.2

virtualIfLAPFCurrentPidMismatch

This counter is associated with the number of
received PID field mismatch
encountered by a Virtual Interface
in the current 15-minute interval.

PerfHist-TC-MIBPerfCurrentCount

.1.3.6.1.4.1.164.3.1.6.2.1.6.5.1.3

virtualIfLAPFCurrentDlciMismatch

This counter is associated with the number of
received DLCI field mismatch
encountered by a Virtual Interface
in the current 15-minute interval.

PerfHist-TC-MIBPerfCurrentCount

Enumerated Values:

1	notApplicable
2	internal
3	lbt
4	systemClk

.1.3.6.1.4.1.164.3.1.6.2.1.6.5.1.4

virtualIfLAPFCurrentMacRxFrames

This counter is associated with the number of
frames received from LAN
by a Virtual Interface
in the current 15-minute interval.

PerfHist-TC-MIBPerfCurrentCount

Enumerated Values:

1	notApplicable
2	none
3	d1ToD3
4	d4ToD12
5	d1
6	d2
7	d3
8	d4
9	d5
10	d6
11	d7
12	d8
13	d9
14	d10
15	d11
16	d12

.1.3.6.1.4.1.164.3.1.6.2.1.6.5.1.5

virtualIfLAPFCurrentMacTxFrames

This counter is associated with the number of
frames transmitted to LAN
by a Virtual Interface
in the current 15-minute interval.

PerfHist-TC-MIBPerfCurrentCount

Enumerated Values:

1	notApplicable
2	none
3	proprietary
4	rip2

.1.3.6.1.4.1.164.3.1.6.2.1.6.5.1.6

virtualIfLAPFIntervalTable

table

.1.3.6.1.4.1.164.3.1.6.2.1.6.6 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk virtualIfLAPFIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::virtualIfLAPFIntervalTable'

The Virtual Interface LAPF Interval table.

virtualIfLAPFIntervalEntry row .1.3.6.1.4.1.164.3.1.6.2.1.6.6.1

An entry in the Virtual Interface Interval table.

Indexes

No indexes recorded

Column Syntax OID

virtualIfLAPFIntervalNlpidMismatch

This counter is associated with the number of
received NLPID field mismatch
encountered by a Virtual Interface in a
particular 15-minute interval in the past 24 hours.

PerfHist-TC-MIBPerfIntervalCount

Enumerated Values:

1	notApplicable
2	none
3	e1Byte
4	e2Byte

.1.3.6.1.4.1.164.3.1.6.2.1.6.6.1.1

virtualIfLAPFIntervalOuiMismatch

This counter is associated with the number of
received OUI field mismatch
encountered by a Virtual Interface in a
particular 15-minute interval in the past 24 hours.

PerfHist-TC-MIBPerfIntervalCount

.1.3.6.1.4.1.164.3.1.6.2.1.6.6.1.2

virtualIfLAPFIntervalPidMismatch

This counter is associated with the number of
received PID field mismatch
encountered by a Virtual Interface in a
particular 15-minute interval in the past 24 hours.

PerfHist-TC-MIBPerfIntervalCount

Enumerated Values:

1	notApplicable
2	disable
3	enable
4	transparent

.1.3.6.1.4.1.164.3.1.6.2.1.6.6.1.3

virtualIfLAPFIntervalDlciMismatch

This counter is associated with the number of
received DLCI field mismatch
by a Virtual Interface in a
particular 15-minute interval in the past 24 hours.

PerfHist-TC-MIBPerfIntervalCount

.1.3.6.1.4.1.164.3.1.6.2.1.6.6.1.4

virtualIfLAPFIntervalMacRxFrames

This counter is associated with the number of
frames received from LAN
by a Virtual Interface in a
particular 15-minute interval in the past 24 hours.

PerfHist-TC-MIBPerfIntervalCount

.1.3.6.1.4.1.164.3.1.6.2.1.6.6.1.5

virtualIfLAPFIntervalMacTxFrames

This counter is associated with the number of
frames transmitted to LAN
encountered by a Virtual Interface in a
particular 15-minute interval in the past 24 hours.

PerfHist-TC-MIBPerfIntervalCount

Enumerated Values:

1	notApplicable
2	standard
3	type1

.1.3.6.1.4.1.164.3.1.6.2.1.6.6.1.6

virtualIfGFPCurrentTable

table

.1.3.6.1.4.1.164.3.1.6.2.1.6.7 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk virtualIfGFPCurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::virtualIfGFPCurrentTable'

The Virtual Interface GFP Current table.

virtualIfGFPCurrentEntry row .1.3.6.1.4.1.164.3.1.6.2.1.6.7.1

An entry in the Virtual Interface
GFP Current table.

Indexes

No indexes recorded

Column Syntax OID

virtualIfGFPCurrentIdleFrameError

This counter is associated with the number of
received GFP IDLE frames that are
detected to be in error,
encountered by a Virtual Interface
in the current 15-minute interval.

PerfHist-TC-MIBPerfCurrentCount

.1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.1

virtualIfGFPCurrentCHecSbError

This counter is associated with the number of
received GFP frames that are detected to have
single-bit errors in the Core
header (i.e. cHEC field) only,
encountered by a Virtual Interface
in the current 15-minute in…

PerfHist-TC-MIBPerfCurrentCount

.1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.2

virtualIfGFPCurrentPtiMismatch

This counter is associated with the number of
rreceived GFP frames that are detected with
a mismatch on the PTI field
(i.e. value of PTI is not equal to
Client Data or Management frame),
encountered by a Virtual Inte…

PerfHist-TC-MIBPerfCurrentCount

.1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.3

virtualIfGFPCurrentExiMismatch

This counter is associated with the number of
received GFP frames that are detected with
a mismatch on the EXI field
(i.e. value of EXI is not equal
to NULL or LINEAR modes),
encountered by a Virtual Interface
in t…

PerfHist-TC-MIBPerfCurrentCount

.1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.4

virtualIfGFPCurrentUpiMismatch

This counter is associated with the number of
received GFP frames that are detected with a
mismatch on the UPI field
(i.e. value of EXI is not equal to 00000001),
encountered by a Virtual Interface
in th…

PerfHist-TC-MIBPerfCurrentCount

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.5

virtualIfGFPCurrentTHecSbError

This counter is associated with the number of
received GFP frames that are detected
to only have single-bit errors in the Type header
(i.e. tHEC field),
encountered by a Virtual Interface
in the current 15-minute int…

PerfHist-TC-MIBPerfCurrentCount

.1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.6

virtualIfGFPCurrentTHecMbError

This counter is associated with the number of
received GFP frames that are detected to
only have multi-bit errors in the
Type header (i.e. tHEC field),
encountered by a Virtual Interface
in the current 15-mi…

PerfHist-TC-MIBPerfCurrentCount

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.7

virtualIfGFPCurrentCidMismatch

This counter is associated with the number of
received GFP frames that are detected to have a
mismatch/unsupported value in the CID field only,
encountered by a Virtual Interface
in the current 15-minute interval.

PerfHist-TC-MIBPerfCurrentCount

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.8

virtualIfGFPCurrentEHecSbError

This counter is associated with the number of
received GFP frames that are detected
to only have single-bit errors
in the Extension header (i.e. eHEC field),
encountered by a Virtual Interface
in the current 15-min…

PerfHist-TC-MIBPerfCurrentCount

Constraints:
range: 0-62

.1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.9

virtualIfGFPCurrentEHecMbError

This counter is associated with the number of
received GFP frames that are detected to only
have single-bit errors in the
Extension header (i.e. eHEC field),
encountered by a Virtual Interface
in the current 15-minu…

PerfHist-TC-MIBPerfCurrentCount

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.10

virtualIfGFPIntervalTable

table

.1.3.6.1.4.1.164.3.1.6.2.1.6.8 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk virtualIfGFPIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::virtualIfGFPIntervalTable'

The Virtual Interface GFP Interval table.

virtualIfGFPIntervalEntry row .1.3.6.1.4.1.164.3.1.6.2.1.6.8.1

An entry in the Virtual Interface
GFP Interval table.

Indexes

No indexes recorded

Column Syntax OID

virtualIfGFPIntervalIdleFrameError

This counter is associated with the number of
received GFP IDLE frames that are detected to be in error,
encountered by a Virtual Interface in a
particular 15-minute interval in the past 24 hours.

PerfHist-TC-MIBPerfIntervalCount

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.1

virtualIfGFPIntervalCHecSbError

This counter is associated with the number of
received GFP frames that are detected to have
single-bit errors in the Core header (i.e. cHEC field) only,
encountered by a Virtual Interface in a
particular 15-minute int…

PerfHist-TC-MIBPerfIntervalCount

Enumerated Values:

1	notApplicable
2	pos
3	clearchannel
4	channelized
5	vc1x

.1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.2

virtualIfGFPIntervalPtiMismatch

This counter is associated with the number of
rreceived GFP frames that are detected with
a mismatch on the PTI field (i.e. value of PTI
is not equal to Client Data or Management frame),
encountered by a Virtual Inter…

PerfHist-TC-MIBPerfIntervalCount

Enumerated Values:

1	notApplicable
2	b16
3	b64

.1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.3

virtualIfGFPIntervalExiMismatch

This counter is associated with the number of
received GFP frames that are detected with
a mismatch on the EXI field (i.e. value of EXI is not
equal to NULL or LINEAR modes),
encountered by a Virtual Inter…

PerfHist-TC-MIBPerfIntervalCount

.1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.4

virtualIfGFPIntervalUpiMismatch

This counter is associated with the number of
received GFP frames that are detected with a
mismatch on the UPI field (i.e. value of EXI
is not equal to 00000001),
encountered by a Virtual Interface in a
particular 15…

PerfHist-TC-MIBPerfIntervalCount

.1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.5

virtualIfGFPIntervalTHecSbError

This counter is associated with the number of
received GFP frames that are detected to only have
single-bit errors in the Type header (i.e. tHEC field),
encountered by a Virtual Interface in a
particular 15-minute inte…

PerfHist-TC-MIBPerfIntervalCount

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.6

virtualIfGFPIntervalTHecMbError

This counter is associated withthe number of
received GFP frames that are detected to only have
multi-bit errors in the Type header (i.e. tHEC field),
encountered by a Virtual Interface in a
particular 15-minute interv…

PerfHist-TC-MIBPerfIntervalCount

.1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.7

virtualIfGFPIntervalCidMismatch

PerfHist-TC-MIBPerfIntervalCount

.1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.8

virtualIfGFPIntervalEHecSbError

PerfHist-TC-MIBPerfIntervalCount

.1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.9

virtualIfGFPIntervalEHecMbError

This counter is associated with the the number of
received GFP frames that are detected to only have
multi-bit errors in the Extension header (i.e. eHEC field),
encountered by a Virtual Interface in a
particular 15-mi…

PerfHist-TC-MIBPerfIntervalCount

Enumerated Values:

2	connect
3	bypass

.1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.10

prtSonetGenTable

table

.1.3.6.1.4.1.164.3.1.6.2.2.1.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtSonetGenTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtSonetGenTable'

Sonet/SDH general port configuration table.

prtSonetGenEntry row .1.3.6.1.4.1.164.3.1.6.2.2.1.1.1

An entry in the Sonet/SDH general port configuration table.

Indexes

No indexes recorded

Column	Syntax	OID
prtSonetGenCnfgIdx This object indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For products that support several configurations, Set can be performed only to the Temporary Config (=255…	Integer32	`.1.3.6.1.4.1.164.3.1.6.2.2.1.1.1.1`
prtSonetGenIdx This object indicates a unique port or interface number. For numbering, see product's spec. For some products, the numbering can equal ifIndex.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.6.2.2.1.1.1.2`
prtSonetGenSdThreshold SD=Signal Degraded Threshold. Units: [10E-]. The threshold is 10E-x relative to the frequency of the data flow. x=3, 4, 5, 6, 7, 8, 9. n3= 10E-3 n4= 10E-4 n5= 10E-5 n6= 10E-6 n7= 10E-7 n8= 10E-8 n9= 10E-9 .	Enumerationr/w Constraints: `range: 1-255`	`.1.3.6.1.4.1.164.3.1.6.2.2.1.1.1.3`
prtSonetGenEedThreshold EED=Excessive Error Defect Threshold. Units: [10E-]. The threshold is 10E-x relative to the frequency of the data flow. x=3, 4, 5, 6, 7, 8, 9. n3= 10E-3 n4= 10E-4 n5= 10E-5 n6= 10E-6 n7= 10E-7 n8= 10E-8 n9= 10E-9 .	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.2.2.1.1.1.4`
prtSonetGenBerEnable Controls the activation of the Line Ber (Bit Error Rate), means whether SD and EED threshold parameters will be enabled.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.2.2.1.1.1.5`

prtSonetStm1Table

table

.1.3.6.1.4.1.164.3.1.6.2.2.2.1 · 1 row entry · 17 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtSonetStm1Table

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtSonetStm1Table'

Sonet/SDH STM-1 port configuration table.

prtSonetStm1Entry row .1.3.6.1.4.1.164.3.1.6.2.2.2.1.1

An entry in the Sonet/SDH STM-1 port configuration table.

Indexes

No indexes recorded

Column Syntax OID

prtSonetStm1CnfgIdx

This object indicates the Idx of the Config being accessed.
Idx of 255 relates to the Temporary (Scratch) Config.
For products that support several configurations, Set can be performed
only to the Temporary Config (=255…

Integer32

Enumerated Values:

1	notApplicable
2	lcasNotActive
3	lcasActive

.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.1

prtSonetStm1Idx

This object indicates a unique port or interface number.
For numbering, see product's spec.
For some products, the numbering can equal ifIndex.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	laps
3	lapf
4	gfp

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.2

prtSonetStm1ClockSrc

Clock Source of the STM-1 port.
lbt = Loop Back Timing.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.3

prtSonetStm1DccMode

DCC Mode. DCC=Data Communication Channel.
d1ToD3 = D1-D3 bytes are used (RS=Regeneration Section).
d4ToD12= D4-D12 bytes are used (MS=Multiplexing Section).
d1.... d12 enable user to select single DCC byte

Enumerationr/w

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.4

prtSonetStm1RoutingProt

Routing Protocol.

Enumerationr/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.5

prtSonetStm1MngProt

Management Protocol over DCC: Proprietary, PPP, Frame Relay,
HDLC or LAPD over HDLC .
ppp = according to STD-51 ( rfc1661/1662)

Enumerationr/w

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.6

prtSonetStm1OperationalMode

Operational Mode.
linear - cannot be selected when there is Redundancy between the
STM-1 ports.

Enumerationr/w

Constraints:
range: 1-1

.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.7

prtSonetStm1VoiceChannel

This parameter enable user to select whether
voice channel will be transferred using E1 byte, E2 Byte, or not at all.

Enumerationr/w

Constraints:
range: 0-83

.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.8

prtSonetStm1OutputRate

This parameter indicates the output rate in cells/sec, which is
supported per port.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	belowMinNoOfVCs
3	withinRange
4	allNorm

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.9

prtSonetStm1S1ProtocolClock

This parameter allows user to select whether to enable use of
Remote Side Clock according to the Protocol passed on S1 Bit.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	off
3	auto
4	manual

.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.10

prtSonetStm1GatewayRingSubnetAddress

This parameter defines subnet for static routing,
together with prtSonetStm1GatewayRingSubnetMask

RFC1155-SMIIpAddressr/w

Enumerated Values:

1	notApplicable
2	managementOnly
3	dataOnly
4	mixed

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.11

prtSonetStm1GatewayRingSubnetMask

This parameter defines subnet for static routing,
together with prtSonetStm1GatewayRingSubnetAddress

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.12

prtSonetStm1MngProtDeviationType

This parameter is used in conjunction with prtSonetStm1MngProt
to define management protocol used & type of deviation
(if exist) from standard.
Standard = no deviation from standard protocol
Type1 = PPP without se…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disabled
3	enabeld

.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.13

prtSonetStm1MngSameIpAsHost

This parameter indicates whether IP address
used for management is same as the device IP address

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.14

prtSonetStm1MngIpAddress

This parameter defines IP address for DCC management
for this link, together with prtSonetStm1MngIpSubnetMask.
This parameter is applicable only if prtSonetStm1MngSameIpAsHost=no.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.15

prtSonetStm1MngIpSubnetMask

This parameter defines IP subnet mask for DCC management
for this link, together with prtSonetStm1MngIpAddress
This parameter is applicable only if prtSonetStm1MngSameIp=no

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.16

prtSonetStm1MngDefaultGateway

This parameter defines default Gateway address for DCC management
for this link.
This parameter is applicable only if prtSonetStm1MngSameIp=no

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.17

prtSonetVcTable

table

.1.3.6.1.4.1.164.3.1.6.2.2.3.1 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtSonetVcTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtSonetVcTable'

Sonet/SDH VC port configuration table.

prtSonetVcEntry row .1.3.6.1.4.1.164.3.1.6.2.2.3.1.1

An entry in the Sonet/SDH VC port configuration table.

Indexes

No indexes recorded

Column Syntax OID

prtSonetVcCnfgIdx

Integer32

.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.1

prtSonetVcIdx

This object indicates a unique port or interface number.
For numbering, see product's spec.
For some products, the numbering can equal ifIndex.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.2

prtSonetVcJTxPathTraceEnable

Enable/Disable Transmitting Jy Path Trace. y=1, 2:
J1 - for VC-4 layer
J2 - for VC-12 layer.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.3

prtSonetVcJRxPathTraceEnable

Enable/Disable checking Jy Path Trace. y=1, 2:
J1 - for VC-4 layer
J2 - for VC-12 layer.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.4

prtSonetVcJPathTrace

Jy Path Trace. y=1, 2:
J1 - for VC-4 layer
J2 - for VC-12 layer.
This object is applicable only if one of the previous 2 objects is 'enable'.

OctetStringr/w

.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.5

prtSonetVcConnect

Connect VCn (n - 11,12,2,3,4) port (yes/no).

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.6

prtSonetVcSignalLabel

Signal Label.
For VC-3:
The SONET standard defines the C2 byte as
the path signal label. The purpose of this byte is to
communicate the payload type being encapsulated by the
SONET Framing OverHead. It allows a single…

OctetStringr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.7

prtSonetVcPathTracePadding

Padding character will pad prtSonetVcJPathTrace string
to fill required number of characters.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.8

prtSonetVcPayloadBlockOnPathTrace

Block payload on this VC upon PathTrace (TIM).

Enumerationr/w

Enumerated Values:

1	notApplicable
2	fcsEnable
3	fcsDisable

.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.9

prtSonetVcPayloadType

Payload type, applicable for STS-1/TUG-3 layer.
vc1x = vc12 or vc11 for SDH, VT1.5, VT2 for SONET.
clear channel - complete TUG-3 or STS-1
For Egate-100:
POS (Packets over Sonet) configuration is valid per STM1/OC3…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.10

prtSonetVcPathTraceSize

Path Trace Size in Bytes - 16 or 64.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.11

prtSonetTuTable

table

.1.3.6.1.4.1.164.3.1.6.2.2.3.2 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtSonetTuTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtSonetTuTable'

The write operation into the Table's Objects is valid only
for the TmpCnfg entry (Scratch).

prtSonetTuEntry row .1.3.6.1.4.1.164.3.1.6.2.2.3.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtSonetTuCnfgIdx

Integer32

.1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.1

prtSonetTuPrtIdx

This object indicates a unique port or interface number.
For port numbering, see product's spec.
For some products, the numbering can equal ifIndex.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.2

prtSonetTuIdx

This object indicates a unique TU (Tributary Unit) within VC-4.
The valid TUs are 1..63.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.3

prtSonetTuConPrtIdx

This object indicates the connected port, when prtSonetTuType=connect.
For port numbering, see product's spec.
For some products, the numbering can equal ifIndex.
notApplicable - will be indicated as 100.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.4

prtSonetTuType

The type of TU (Tributary Unit).
connect - connected to one of the E1 ports.
bypass - bypassed to the other VC4 port.
TUs that are not connected or bypassed, will not exist in this table.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.5

prtSonetTuMode

TU Mode of connection.
addAndDrop - Add & Drop
add - Add (TU receives from the E1 ports).

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.6

prtSonetTuRowStatus

Creation/Deletion of rows in the table.

SNMPv2-TCRowStatusr/w

Enumerated Values:

1	notApplicable
2	rx
3	tx
4	both

Description:

.1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.7

vcGroupCnfgTable

table

.1.3.6.1.4.1.164.3.1.6.2.2.4.1 · 1 row entry · 20 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk vcGroupCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::vcGroupCnfgTable'

The Virtual Concatenation Group configuration table.

vcGroupCnfgEntry row .1.3.6.1.4.1.164.3.1.6.2.2.4.1.1

An entry in the Virtual Concatenation Group
configuration table.

Indexes

No indexes recorded

Column Syntax OID

vcGroupCnfgIdx

Integer32

.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.1

vcGroupCnfgNumber

Virtual Concatenation Group Number.
For FCD-155 up to eight groups are defined
valid values are 1..8.
For MP-4100, group ifIndex is used.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.2

vcGroupCnfgRowStatus

Creation/Deletion of rows in the table.

SNMPv2-TCRowStatusr/w

Constraints:
range: 0-62

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.3

vcGroupCnfgVcType

User may select type of SDH Virtual Containers (VC)
(SONET Virtual Tributaries VT ) to be concatenated
in this Virtual Concatenation Group.
For SDH, values 2,3,4 and 8 are valid.
For SONET, values 5, 6,7 are valid.

Enumerationr/w

Constraints:
range: 1-1

.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.4

vcGroupCnfgNoOfVCs

User may select number of Virtual Containers (VC)
(SONET Virtual Tributaries VT ) to be concatenated
in this Virtual Concatenation Group.
Valid range for this number depends on
type VC selected by vcGroupCnfgVCType
F…

Integer32r/w

Enumerated Values:

1	notApplicable
2	fixed
3	add
4	norm
5	eos
6	idle
7	dnu

.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.5

vcGroupCnfgLCAS

This object controls Link Capacity Adjustment
Scheme (LCAS) activation.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	fixed
3	add
4	norm
5	eos
6	idle
7	dnu

.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.6

vcGroupCnfgEncapsulation

This object enables user to select encapsulation method.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.7

vcGroupCnfgGroupIfIndex

The ifIndex assigend to this group.

IF-MIBInterfaceIndex

Type Constraints:
range: 1..2147483647

Description:

A unique value, greater than zero, for each interface or
interface sub-layer in the managed system. It is
recommended that values are assigned contiguously starting
from 1. The value for each interface sub-layer must …

.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.8

vcGroupCnfgRip2

This object controls RIP 2.
User may select to send RIP 2 message over
selected group or not

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.9

vcGroupCnfgGfpChId

Generic Framing Procedure (GFP) Channel ID,
Valid only when vcGroupCnfgEncapsulation = gfp (4)
Valid values are 0x00 - oxFF (hex)

Integer32r/w

.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.10

vcGroupCnfgK4

This object controls whether K4 byte
(of Line Overhead) is used as an indication for
virtual concatenation (VCAT).
This object is applicable, when VCG
includes only a single Virtual Container (VC)
(or SONET VT)

Enumerationr/w

Enumerated Values:

1	notApplicable
2	off
3	on

.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.11

vcGroupCnfgExSignalLabel

Extended Signal Label.
Relevant only when vcGroupCnfgK4 = yes(3).
Agents that do not support this feature will send SIZE 0.

OctetStringr/w

Enumerated Values:

1	notApplicable
2	off
3	on

.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.12

vcGroupCnfgLcasMinNoOfVCs

Minimum number of VC's to declare alarm, in LCAS mode.
Applicable only when LCAS is active
(vcGroupCnfgLCAS =lcasActive)
1...63 for SDH, 1...84 for SONET
0= not applicable.

Integer32r/w

Enumerated Values:

1	notApplicable
3	add
4	norm
6	idle
7	dnu
8	remove

.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.13

vcGroupCnfgLcasStatus

This object summarize LCAS states of all VCs in VCG:

belowMinNoOfVCs - Number of VCs in Norm state is less than
the minimum number of VCs
(indicated by vcGroupCnfg…

Enumeration

Enumerated Values:

1	notApplicable
6	idle
9	ok
10	fail

.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.14

vcGroupCnfgMappingMode

This object define Path Protection mode for VCG.
Auto - the entire mapping for Virtual Concatenation Group x
is copied automatically by agent for the protection group
to same TUs on the other SONET/SDH link which re…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.15

vcGroupCnfgTrafficType

This object allows to select traffic type for
specific VCG.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.16

vcGroupCnfgGroupName

Virtual Concatenation Group (VCG) Name.
String length is limited to 15 characters.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.17

vcGroupCnfgLoopDetection

VCAT Loop detecetion enabled.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.18

vcGroupCnfgLcasWaitToRestore

Time duration (in milliseconds units) waited after
errors on channel stopped, before channel is reused.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.19

vcGroupCnfgLcasHoldOff

Time duration (in milliseconds units) in which errors on channel
are disregarded. (Threshold)

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.20

vcgGfpMuxCnfgTable

table

.1.3.6.1.4.1.164.3.1.6.2.2.4.2 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk vcgGfpMuxCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::vcgGfpMuxCnfgTable'

The Virtual Concatenation Group GFP Mux configuration table.

vcgGfpMuxCnfgEntry row .1.3.6.1.4.1.164.3.1.6.2.2.4.2.1

An entry in the Virtual Concatenation Group GFP Mux
configuration table.

Indexes

No indexes recorded

Column Syntax OID

vcgGfpMuxCnfgIdx

This object indicates the Index of the configuration being accessed.
Index of 255 relates to the Temporary (Scratch) coninguration.
For products that support several configurations, Set can be performed
only to the Temp…

Integer32

Enumerated Values:

2	working
3	protection

.1.3.6.1.4.1.164.3.1.6.2.2.4.2.1.1

vcgGfpMuxCnfgMuxNumber

Virtual Concatenation Group GFP Mux Number.
Refer to device specification for definition of
- maximum number of GFP-mux.
- concatenation of Slot and GFP mux number.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.2.2.4.2.1.2

vcgGfpMuxCnfgRowStatus

Creation/Deletion of rows in the table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.3.1.6.2.2.4.2.1.3

vcgGfpMuxCnfgMuxName

Virtual Concatenation Group, GFP Mux name.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Enumerated Values:

2	off
3	on

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.3.1.6.2.2.4.2.1.4

vcgGfpMuxCnfgPrimeGroup

Index of Virtual Concatenation Group used as
Primary for the GFP mux created
for FCD 155 up to 8 Virtual Concatenation Group are defined:
1 -> Virtual Concatenation Group 1
2 -> Virtual Concatenation Group 2
3 -> V…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	noOp
2	clear
3	forcedSwitch
4	lockout

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.2.2.4.2.1.5

vcgGfpMuxCnfgGrpBwAlloc

This object indicates the allocated bandwidth (BW) to each
Virtual Concatenation Group (VCG).
Each nibble indicates BW percentage, in 12.5% steps,
assigned to a group.

For FCD-155, there may be 4 or 8…

OctetStringr/w

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.1.6.2.2.4.2.1.6

virtualIfGenTable

table

.1.3.6.1.4.1.164.3.1.6.2.2.5.1 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk virtualIfGenTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::virtualIfGenTable'

Sonet/SDH general port configuration table.

virtualIfGenEntry row .1.3.6.1.4.1.164.3.1.6.2.2.5.1.1

An entry in the Sonet/SDH general port configuration table.

Indexes

No indexes recorded

Column	Syntax	OID
virtualIfGenCnfgIdx This object indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For products that support several configurations, Set can be performed only to the Temporary Config (=255…	Integer32	`.1.3.6.1.4.1.164.3.1.6.2.2.5.1.1.1`
virtualIfGenIdx This object indicates a unique port or interface number. For numbering, see product's spec. For some products, the numbering can equal ifIndex.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.6.2.2.5.1.1.2`
virtualIfGenFrameFormat The frame format. fcsEnabe = Frame will be sent with the FCS bits. fcsDisable = Frame will be sent without the FCS bits .	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.2.2.5.1.1.3`

prtSonetXConnectTable

table

.1.3.6.1.4.1.164.3.1.6.2.3.1 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtSonetXConnectTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtSonetXConnectTable'

The write operation into the Table's Objects is valid only
for the TmpCnfg entry (Scratch).

prtSonetXConnectEntry row .1.3.6.1.4.1.164.3.1.6.2.3.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtSonetXConnectCnfgIdx

Integer32

.1.3.6.1.4.1.164.3.1.6.2.3.1.1.1

prtSonetXConnectPrtIdx

This object indicates a unique port or interface number.
For port numbering, see product's spec.
For some products, the numbering can equal ifIndex.

SNMPv2-SMIInteger32

Constraints:
range: 0-899

.1.3.6.1.4.1.164.3.1.6.2.3.1.1.2

prtSonetXConnectConPrtIdx

This object indicates the connected port.
For port numbering, see product's spec.
For some products, the numbering can equal ifIndex.
notApplicable - will be indicated as 255.

SNMPv2-SMIInteger32

Constraints:
range: 0-96

.1.3.6.1.4.1.164.3.1.6.2.3.1.1.3

prtSonetXConnectAUGIdx

This object indicates an AUG (Administrative Unit Group) within STM-N.
The valid AUGs values are:
1 for STM-1
1...4 for STM-4,
1..16 for STM-16 and
1..64 for STM-64 (STM-64)
255 designates NA.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.2.3.1.1.4

prtSonetXConnectTUG3Idx

This object indicates a TUG-3 (Tributary Unit Group 3) within VC-4.
The valid TUG3s are values are 1..3. and 255 which designates NA

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.2.3.1.1.5

prtSonetXConnectTUG2Idx

This object indicates a TUG2 (Tributary Unit Group 2 ) within VC-3.
The valid TUG2's values are 1..7 and 255 which designates NA

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.2.3.1.1.6

prtSonetXConnectTUnIdx

This object indicates a TUn within TUG-2 or TUG-3
(Tributary Unit n, where n is 2, 12 or 11 within TUG-2,
or 3 within TUG-3)
valid values are
1 for TU-2
1 for TU-3
1..4 for TU-11
1..3 for TU-12
…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.2.3.1.1.7

prtSonetXConnectRowStatus

Creation/Deletion of rows in the table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.3.1.6.2.3.1.1.8

prtSonetXConnectDirection

TU direction of connection.
rx=Drop
tx=Add
both = Add & Drop

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.2.3.1.1.9

prtSonetXConnectTuNumber

This object indicates which TU is used in prtSonetXConnectTUnIdx

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.2.3.1.1.10

prtSonetXConnectMode

TU Mode of connection.
addAndDrop - Add & Drop
bypass - bypassed to the other VC4 port.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.2.3.1.1.11

prtSonetVcStatTable

table

.1.3.6.1.4.1.164.3.1.6.2.4.1 · 1 row entry · 14 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtSonetVcStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtSonetVcStatTable'

VC Status Table

prtSonetVcStatEntry row .1.3.6.1.4.1.164.3.1.6.2.4.1.1

An entry in the VC status Table.

Indexes

No indexes recorded

Column	Syntax	OID
prtSonetVcRxJPathTrace Jy Path Trace value received from network. y=1, 2: J1 - for VC-4 layer J2 - for VC-12 layer.	OctetString	`.1.3.6.1.4.1.164.3.1.6.2.4.1.1.1`
prtSonetVcRxSignalLabel Signal Label received from network. For VC-3: The SONET standard defines the C2 byte as the path signal label. The purpose of this byte is to communicate the payload type being encapsulated by the SONET Framing OverHe…	OctetString	`.1.3.6.1.4.1.164.3.1.6.2.4.1.1.2`
prtSonetVcLcasSourceState Fixed - This is an indication that this end uses fixed bandwidth (non-LCAS mode) Add - This member is about to be added to the group Norm - Normal transmission. EOS - E…	Enumeration	`.1.3.6.1.4.1.164.3.1.6.2.4.1.1.3`
prtSonetVcLcasSinkState Fixed - This is an indication that this end uses fixed bandwidth (non-LCAS mode) Add - This member is about to be added to the group Norm - Normal transmission. EOS - E…	Enumeration	`.1.3.6.1.4.1.164.3.1.6.2.4.1.1.4`
prtSonetVcStatus This variable indicates the Status of the interface. It contains failure state information. The variable is a bit map represented as a sum, therefore, it can represent multiple failures simultaneously. The sonetVC…	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.6.2.4.1.1.5`
prtSonetVcRxSeqNumber This variable indeticates the LCAS Rx sequence number of this VC.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.4.1.1.6`
prtSonetVcTxSeqNumber This variable indicates the LCAS Tx sequence number of this VC.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.4.1.1.7`
prtSonetVcMfiDiffDelay This variable indicates time difference (based on MFI field) from the fastest channel (on which it will be 0), in miliSeconds units	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.4.1.1.8`
prtSonetVcLoMF This variable indicates loss of Multiframe defect.	Enumeration	`.1.3.6.1.4.1.164.3.1.6.2.4.1.1.9`
prtSonetVcLoopStatus This variable indicates Loop Status.	Enumeration	`.1.3.6.1.4.1.164.3.1.6.2.4.1.1.10`
prtSonetVcLcasTxStateMachineStatus LCAS State machine status.	Enumeration Constraints: `range: 4-4`	`.1.3.6.1.4.1.164.3.1.6.2.4.1.1.11`
prtSonetVcLcasRxStateMachineStatus LCAS State machine status.	Enumeration	`.1.3.6.1.4.1.164.3.1.6.2.4.1.1.12`
prtSonetVcMFLengthErrorCounter Counts the multi-frames that had wrong length (shorter or longer)	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.4.1.1.13`
prtSonetVcCntrlPktCRCErrorCounter Counts Number of Control Packet CRC errors	SNMPv2-SMICounter32 Constraints: `range: 1-96`	`.1.3.6.1.4.1.164.3.1.6.2.4.1.1.14`

prtSonetPathProtTable

table

.1.3.6.1.4.1.164.3.1.6.2.4.2 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtSonetPathProtTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtSonetPathProtTable'

Path Protection Monitoring Table

prtSonetPathProtEntry row .1.3.6.1.4.1.164.3.1.6.2.4.2.1

An entry in the Path Protection monitoring Table.
This table indicates for each protected interface
which VCs are mapped as Working VC,
which VCs are mapped as Protection VC,
and which of them are currently active.

Indexes

No indexes recorded

Column	Syntax	OID
prtSonetPathProtProtectedInterface Interface protected by path-protection, e.g. PDH (E1/T1/E3/T3) port, VCG (Virtual Concatenation Group).	IF-MIBInterfaceIndex Type Constraints: `range: 1..2147483647` Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	`.1.3.6.1.4.1.164.3.1.6.2.4.2.1.1`
prtSonetPathProtIdx Runing index of entries which are mapped to a specific interface, indicated by PrtSonetPathProtProtectedInterface. e.g - multiple working VCs and protection VCs are mapped to single Virtual Concatenation Group …	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.4.2.1.2`
prtSonetPathProtWorkingVc A VC mapped to interface indicated by prtSonetPathProtProtectedInterface as working VC. The value of this object may be equal to the value of ifIndex of working VC	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.4.2.1.3`
prtSonetPathProtProtectionVc A VC mapped to interface indicated by prtSonetPathProtProtectedInterface as protection VC. The value of this object may be equal to the value of ifIndex of protection VC	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.2.4.2.1.4`
prtSonetPathProtActiveVc This object indicates which of the path protection VCs is currently active.	Enumeration	`.1.3.6.1.4.1.164.3.1.6.2.4.2.1.5`

radApsConfigTable

table

.1.3.6.1.4.1.164.3.1.6.2.5.1 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radApsConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radApsConfigTable'

An Augment to the APS Configuration Table
(apsConfigTable in APS-MIB).

radApsConfigEntry row .1.3.6.1.4.1.164.3.1.6.2.5.1.1

An entry in the table.

Indexes

No indexes recorded

Column	Syntax	OID
radApsConfigClearCounters Setting this object to on(3) will clear APS Counters. Upon performing this operation, the value will be automatically changed to off(2).	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.2.5.1.1.1`
radApsConfigCommandAndStatus noOp - initial state only (cannot be Set by user). clear - clearing the last performed command. Can be Set only if previous state was other than noOp or clear. forcedSwitch - tra…	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.2.5.1.1.2`
radApsConfigFlipOnSD Flip active channel according to SD (Signal Degradation).	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.2.5.1.1.3`

radApsStatusTable

table

.1.3.6.1.4.1.164.3.1.6.2.5.2 · 1 row entry · 1 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radApsStatusTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radApsStatusTable'

An Augment to the APS Status Table
(apsStatusTable in APS-MIB).

radApsStatusEntry row .1.3.6.1.4.1.164.3.1.6.2.5.2.1

An entry in the table.

Indexes

No indexes recorded

Column	Syntax	OID
radApsStatusCurrentWorkingChannel This object indicates the port/interface index of the Current Working Channel.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.6.2.5.2.1.1`

vcGroupStatTable

table

.1.3.6.1.4.1.164.3.1.6.2.6.1 · 1 row entry · 1 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk vcGroupStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::vcGroupStatTable'

Sonet/SDH VCG status table.

vcGroupStatEntry row .1.3.6.1.4.1.164.3.1.6.2.6.1.1

An entry in the Sonet/SDH VCG gen staus table.

Indexes

No indexes recorded

Column	Syntax	OID
vcGroupStatRemoteChannelStatus Status of remote VCG channels as received in the local station, represented by 1 bit per channel. Refer to product spec for details.	OctetString	`.1.3.6.1.4.1.164.3.1.6.2.6.1.1.1`

prtSDs3IfTable

table

.1.3.6.1.4.1.164.3.1.6.3.1.1 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtSDs3IfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtSDs3IfTable'

The DS3 interface table.

prtDs3IfEntry row .1.3.6.1.4.1.164.3.1.6.3.1.1.1

An entry in the DS3 interface table.

Indexes

No indexes recorded

Column	Syntax	OID
prtDs3IfTimeElapsed The number of seconds that have elapsed since the beginning of the near end current error- measurement period.	Integer32	`.1.3.6.1.4.1.164.3.1.6.3.1.1.1.1`
prtDs3IfValidIntervals The number of previous near end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complet…	Integer32	`.1.3.6.1.4.1.164.3.1.6.3.1.1.1.2`

prtDs3CurrentTable

table

.1.3.6.1.4.1.164.3.1.6.3.1.2 · 1 row entry · 19 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtDs3CurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtDs3CurrentTable'

The DS3 Current table.

prtDs3CurrentEntry row .1.3.6.1.4.1.164.3.1.6.3.1.2.1

An entry in the DS3 Current table.

Indexes

No indexes recorded

Column Syntax OID

prtDs3CurrentLOS

The counter associated with the number of LOS
seconds, encountered by a DS3 interface in
the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.3.1.2.1.1

prtDs3CurrentOOF

The counter associated with the number of OOF
seconds, encountered by a DS3
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.3.1.2.1.2

prtDs3CurrentLOC

The counter associated with the number of LOC
seconds, encountered by a DS3
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.3.1.2.1.3

prtDs3CurrentAIS

The counter associated with the number of AIS
seconds, encountered by a DS3
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.3.1.2.1.4

prtDs3CurrentRDI

The counter associated with the number of RDI
seconds, encountered by a DS3
interface.

SNMPv2-SMIGauge32

Enumerated Values:

1	loopTiming
2	localTiming
3	throughTiming
4	system

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.3.1.2.1.5

prtDs3CurrentUAS

The counter associated with the number of UAS,
encountered by a SONET interface.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.3.1.2.1.6

prtDs3CurrentBIP

The counter associated with the number of
BIP errors, encountered by a DS3
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.3.1.2.1.7

prtDs3CurrentFEBE

The counter associated with the number of
FEBE errors, encountered by a DS3
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.3.1.2.1.8

prtDs3CurrentSLM

The counter associated with the number of SLM
seconds, encountered by an E3 (only )
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.3.1.2.1.9

prtDs3CurrentSES

The counter associated with the number of SES
encountered by a E3
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.3.1.2.1.10

prtDs3CurrentES

The number of Errored Seconds, encountered by a
DS3 interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.3.1.2.1.11

prtDs3CurrentBitParity

Bit Parity Error counter. Relevant to T3 only.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.3.1.2.1.12

prtDs3CurrentPlcpLOF

The counter associated with the number of LOF
seconds, encountered by a DS3
interface in one of the previous 96, individual 15
minute, intervals. This counter is relevant for plcpInternal(5)
or plcpExternal(6) configur…

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.3.1.2.1.13

prtDs3CurrentPlcpRAI

Receiving Yellow/Remote Alarm Indication. This counter is
relevant for PLCP (external/internal) frame types only.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.3.1.2.1.14

prtDs3CurrentPlcpBIP

The counter associated with the number of BIP errors,
encountered by a DS3 interface in the current 15 minute
interval. This counter is relevant for PLCP (external/internal)
frame types only.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.3.1.2.1.15

prtDs3CurrentPlcpFEBE

The counter associated with the number of FEBE
errors, encountered by a DS3 interface in the current
15 minute interval. This counter is relevant for PLCP
(external/internal) frame types only.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.3.1.2.1.16

prtDs3CurrentBPV

Number of BPVs (Bi-Polar Violations) , encountered by a
DS3 interface in the current 15 minute interval.
This object is relevant only for Electrical Line
of Fomi-E3/T3.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.3.1.2.1.17

prtDs3CurrentLCE

Number of LCE (Link Code Errors) encountered
by a DS3 interface in the current 15 minute interval.
This object is relevant only for Optical Links
of Fomi-E3/T3.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.3.1.2.1.18

prtDs3CurrentStatus

The statuses of the current interval:
0 - Valid.
1 - redundantLinkSwitch - the link has been switched
by a redundancy mechanism.
2 - discontinuity - module was partialy out.
4 - notValid - module is out.

OctetString

.1.3.6.1.4.1.164.3.1.6.3.1.2.1.19

prtDs3IntervalTable

table

.1.3.6.1.4.1.164.3.1.6.3.1.3 · 1 row entry · 20 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtDs3IntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtDs3IntervalTable'

The DS3 Interval table.

prtDs3IntervalEntry row .1.3.6.1.4.1.164.3.1.6.3.1.3.1

An entry in the DS3 Interval table.

Indexes

No indexes recorded

Column	Syntax	OID
prtDs3IntervalNumber A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).	Integer32	`.1.3.6.1.4.1.164.3.1.6.3.1.3.1.1`
prtDs3IntervalLOS The counter associated with the number of LOS seconds , encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.3.1.2`
prtDs3IntervalOOF The counter associated with the number of OOF seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.3.1.3`
prtDs3IntervalLOC The counter associated with the number of LOC seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.3.1.4`
prtDs3IntervalAIS The counter associated with the number of AIS seconds, encountered by a SONET interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.3.1.5`
prtDs3IntervalRDI The counter associated with the number of RDI seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.3.1.6`
prtDs3IntervalUAS The counter associated with the number of UAS, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.3.1.7`
prtDs3IntervalBIP The counter associated with the number of BIP errors, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.3.1.8`
prtDs3IntervalFEBE The counter associated with the number of FEBE errors, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.3.1.9`
prtDs3IntervalSLM The counter associated with the number of SLM seconds, encountered by an E3 interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.3.1.10`
prtDs3IntervalSES The counter associated with the number of SES encountered by a E3 interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.3.1.11`
prtDs3IntervalES The number of Errored Seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.3.1.12`
prtDs3IntervalBitParity Bit Parity Error counter. Relevant to T3 only.	SNMPv2-SMIGauge32 Constraints: `range: 4-4`	`.1.3.6.1.4.1.164.3.1.6.3.1.3.1.13`
prtDs3IntervalPlcpLOF The counter associated with the number of LOF seconds, encountered by a DS3 interface in one of the previous 96, individual 15 minute, intervals. This counter is relevant for plcpInternal(5) or plcpExternal(6) configur…	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.3.1.14`
prtDs3IntervalPlcpRAI Receiving Yellow/Remote Alarm Indication. This counter is relevant for PLCP (external/internal) frame types only.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.3.1.15`
prtDs3IntervalPlcpBIP The counter associated with the number of BIP errors, encountered by a DS3 interface in the current 15 minute interval. This counter is relevant for PLCP (external/internal) frame types only.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.3.1.16`
prtDs3IntervalPlcpFEBE The counter associated with the number of FEBE errors, encountered by a DS3 interface in the current 15 minute interval. This counter is relevant for PLCP (external/internal) frame types only.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.3.1.17`
prtDs3IntervalBPV Number of BPVs (Bi-Polar Violations) , encountered by a DS3 interface in the specified 15 minute interval. This object is relevant only for Electrical Line of Fomi-E3/T3.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.3.1.18`
prtDs3IntervalLCE Number of LCE (Link Code Errors) encountered by a DS3 interface in the specified 15 minute interval. This object is relevant only for Optical Links of Fomi-E3/T3.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.3.1.19`
prtDs3IntervalStatus The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.	OctetString	`.1.3.6.1.4.1.164.3.1.6.3.1.3.1.20`

prtDs3TotalTable

table

.1.3.6.1.4.1.164.3.1.6.3.1.4 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtDs3TotalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtDs3TotalTable'

A list of Total entries.

prtDs3TotalEntry row .1.3.6.1.4.1.164.3.1.6.3.1.4.1

An entry of Total table.

Indexes

No indexes recorded

Column	Syntax	OID
prtDs3TotalUAS Number of UASs (Unavailable Seconds) , encountered by a DS3 interface in the previous 96 intervals. Invalid 15 minute intervals count as 0.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.4.1.6`
prtDs3TotalBPV Number of BPVs (Bi-Polar Violations) , encountered by a DS3 interface in the previous 96 intervals. Invalid 15 minute intervals count as 0.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.4.1.17`
prtDs3TotalLCE Number of LCE (Link Code Errors) encountered by a DS3 interface in the previous 96 intervals. Invalid 15 minute intervals count as 0.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.4.1.18`
prtDs3TotalSES Number of SES (Severely Errored Seconds) encountered by a DS3 interface in the previous 96 intervals. Invalid 15 minute intervals count as 0.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.1.4.1.19`

dsx3XConfigTable

table

.1.3.6.1.4.1.164.3.1.6.3.2 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk dsx3XConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::dsx3XConfigTable'

An extension to the DS3 Configuration table.

dsx3XConfigEntry row .1.3.6.1.4.1.164.3.1.6.3.2.1

An entry containing additional configuration
parameters.

Indexes

No indexes recorded

Column	Syntax	OID
dsx3AisEnable Enable/ disable AIS transmit when Ethernet (for TDMoIP) line is disconnected.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.3.2.1.1`
dsx3TxClockSource The source of Transmit Clock. loopTiming indicates that the recovered receive clock is used as the transmit clock. localTiming indicates that a local clock source is used or that an externa…	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.3.2.1.2`

dsx3MappingTable

table

.1.3.6.1.4.1.164.3.1.6.3.3 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk dsx3MappingTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::dsx3MappingTable'

The DS3/E3 mapping table associates DS3/E3 channels
with logical or physical interfaces.
          
For example, consider a DS3 device with 16 T1's and 1 VCG.
		There are 28 logical/internal channels, numbered 1 through 28
		but only 17 are actually connected.
          
		We might describe the allocation of channels, in the dsx3MappingTable, as
follows:
dsx3MappingIfIndex.1. 1 = 1001  dsx3MappingIfIndex.1.15 = 1015
dsx3MappingIfIndex.1. 2 = 1002  dsx3MappingIfIndex.1.16 = 1016
dsx3MappingIfIndex.1. 3 = 1003  dsx3MappingIfIndex.1.17 = 1017
dsx3MappingIfIndex.1. 4 = 1004  dsx3MappingIfIndex.1.18 =  0
dsx3MappingIfIndex.1. 5 = 1005  dsx3MappingIfIndex.1.19 =  0
dsx3MappingIfIndex.1. 6 = 1006  dsx3MappingIfIndex.1.20 =  0
dsx3MappingIfIndex.1. 7 = 1007  dsx3MappingIfIndex.1.21 =  0
dsx3MappingIfIndex.1. 8 = 1008  dsx3MappingIfIndex.1.22 =  0
dsx3MappingIfIndex.1. 9 = 1009  dsx3MappingIfIndex.1.23 =  0
dsx3MappingIfIndex.1.10 = 1010  dsx3MappingIfIndex.1.24 =  0
dsx3MappingIfIndex.1.11 = 1011  dsx3MappingIfIndex.1.25 =  0
dsx3MappingIfIndex.1.12 = 1012  dsx3MappingIfIndex.1.26 =  0
dsx3MappingIfIndex.1.13 = 1013  dsx3MappingIfIndex.1.27 =  0
dsx3MappingIfIndex.1.14 = 1014  dsx3MappingIfIndex.1.28 =  0
          
		Note that in the case above all channels are mapped to one T3 port with ifIndex = 1.
		The Channels 1...28 are represented via the 2nd index.
		The values of 1001...1016 are the T1 interface ifIndexes.
		The value of 1017 is the ifIndex of the VCG.
	    Unconnected channels have a value of 0.

dsx3MappingEntry row .1.3.6.1.4.1.164.3.1.6.3.3.1

An entry in the DS3 mapping table.

Indexes

No indexes recorded

Column	Syntax	OID
dsx3MappingDs3Index The index value which uniquely identifies the DS3/E3 interface to which this entry is applicable. This value is also equal to dsx3LineIndex used in dsx3ConfigEntry. For RICi-16 this is the …	IF-MIBInterfaceIndex Type Constraints: `range: 1..2147483647` Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	`.1.3.6.1.4.1.164.3.1.6.3.3.1.1`
dsx3MappingNumber The channel number for this entry. For RICi-16 this is the channel number 1...28.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.3.3.1.2`
dsx3MappingIfIndex An index value that uniquely identifies a logical or physical interface mapped to a DS3/E3 channel. If no interface is currently using a channel, the value should be zero. If a single interface occupies more than one c…	IF-MIBInterfaceIndexr/w Type Constraints: `range: 1..2147483647` Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	`.1.3.6.1.4.1.164.3.1.6.3.3.1.3`

dsx1XCurrentTable

table

.1.3.6.1.4.1.164.3.1.6.4.1.2 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk dsx1XCurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::dsx1XCurrentTable'

A list of current statistics entries.  This table
contains additional objects for the current table.

dsx1XCurrentEntry row .1.3.6.1.4.1.164.3.1.6.4.1.2.1

An entry containing additional statistical counters
applicable to a particular current table.

Indexes

No indexes recorded

Column Syntax OID

dsx1CurrentLOS

The counter associated with the number of LOS
seconds, encountered by a DS1 interface in
the current 15 minute interval.

PerfHist-TC-MIBPerfCurrentCount

Enumerated Values:

1	csu
2	dsu

.1.3.6.1.4.1.164.3.1.6.4.1.2.1.1

dsx1CurrentLOF

The counter associated with the number of LOF
seconds, encountered by a DS1
interface in the current 15 minute interval.

PerfHist-TC-MIBPerfCurrentCount

Enumerated Values:

1	notApplicable
2	neg75dB
3	neg15dB
4	neg225dB
5	zerodB

.1.3.6.1.4.1.164.3.1.6.4.1.2.1.2

dsx1CurrentLOC

Loss Of Cell delineation. Counts number of cells the ATM UNI cells receiver
lost cells delineation .

PerfHist-TC-MIBPerfCurrentCount

Enumerated Values:

1	notApplicable
2	longHaul
3	shortHaul

.1.3.6.1.4.1.164.3.1.6.4.1.2.1.3

dsx1CurrentAIS

The counter associated with the number of AIS
seconds, encountered by a DS1
interface in the current 15 minute interval.

PerfHist-TC-MIBPerfCurrentCount

Enumerated Values:

1	other
2	sec1
3	sec10
4	immediate

.1.3.6.1.4.1.164.3.1.6.4.1.2.1.4

dsx1CurrentRAI

Remote Alarm Indication: Transmitted in the outgoing direction
(toward the PABX) over FDL bits when the DS1 device detected
an incoming Loss Of Frame. Received from the far end (PABX)
over FDL when it detects a Loss …

PerfHist-TC-MIBPerfCurrentCount

.1.3.6.1.4.1.164.3.1.6.4.1.2.1.5

dsx1CurrentLOMF

Loss of Multi-Frame sequence in E1 time slot 16.

PerfHist-TC-MIBPerfCurrentCount

.1.3.6.1.4.1.164.3.1.6.4.1.2.1.6

dsx1CurrentFEBE

Far End Block Errors, as reported in the first bit
of frames 13 and 15, on multiframe E1 lines with CRC4,
in the current 15 minute interval.

PerfHist-TC-MIBPerfCurrentCount

.1.3.6.1.4.1.164.3.1.6.4.1.2.1.7

dsx1CurrentStatus

OctetString

Enumerated Values:

1	notApplicable
2	notActive
3	active

.1.3.6.1.4.1.164.3.1.6.4.1.2.1.8

dsx1CurrentBPV

The counter associated with the number of BPVs (Bi-Polar Violations)
encountered by a DS1 interface in the current 15 minute interval.

PerfHist-TC-MIBPerfCurrentCount

Enumerated Values:

1	off
2	on

.1.3.6.1.4.1.164.3.1.6.4.1.2.1.9

dsx1CurrentLOCRCMF

Loss of CRC4 Multi-Frame sequence in E1.
encountered in the current 15 minute interval

PerfHist-TC-MIBPerfCurrentCount

Enumerated Values:

1	loopTiming
2	localTiming
3	throughTiming
4	adaptive
5	system

.1.3.6.1.4.1.164.3.1.6.4.1.2.1.10

dsx1CurrentLOFC

Counts the number of loss of frame events measured.
encountered in the current 15 minute interval

PerfHist-TC-MIBPerfCurrentCount

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.1.6.4.1.2.1.11

dsx1CurrentCRCErrors

Counts the number of CRC error events,
encountered in the current 15 minute interval.

PerfHist-TC-MIBPerfCurrentCount

Constraints:
range: 4-4

.1.3.6.1.4.1.164.3.1.6.4.1.2.1.12

dsx1XIntervalTable

table

.1.3.6.1.4.1.164.3.1.6.4.1.3 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk dsx1XIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::dsx1XIntervalTable'

A list of Interval entries.  This table
contains additional objects for the interval table.

dsx1XIntervalEntry row .1.3.6.1.4.1.164.3.1.6.4.1.3.1

An entry containing additional statistical counters
applicable to a particular interval table.

Indexes

No indexes recorded

Column Syntax OID

dsx1IntervalLOS

The counter associated with the number of LOS
seconds , encountered by a DS1 interface in
one of the previous 96, individual 15 minute,
intervals.

PerfHist-TC-MIBPerfIntervalCount

Enumerated Values:

1	notApplicable
2	r56
3	r64

.1.3.6.1.4.1.164.3.1.6.4.1.3.1.1

dsx1IntervalLOF

The counter associated with the number of OOF
seconds, encountered by a DS1
interface in one of the previous 96, individual 15
minute, intervals.

PerfHist-TC-MIBPerfIntervalCount

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.1.6.4.1.3.1.2

dsx1IntervalLOC

Loss Of Cell delineation. Counts number of cells the ATM UNI cells receiver
lost cells delineation .

PerfHist-TC-MIBPerfIntervalCount

Enumerated Values:

1	notApplicable
2	local
3	transparent
4	remote

.1.3.6.1.4.1.164.3.1.6.4.1.3.1.3

dsx1IntervalAIS

The counter associated with the number of AIS
seconds, encountered by a SONET
interface in one of the previous 96, individual 15
minute, intervals.

PerfHist-TC-MIBPerfIntervalCount

.1.3.6.1.4.1.164.3.1.6.4.1.3.1.4

dsx1IntervalRAI

PerfHist-TC-MIBPerfIntervalCount

Enumerated Values:

1	notApplicable
2	space
3	mark
4	spaceMark
5	markSpace

.1.3.6.1.4.1.164.3.1.6.4.1.3.1.5

dsx1IntervalLOMF

Loss of Multi-Frame sequence in E1 time slot 16.

PerfHist-TC-MIBPerfIntervalCount

.1.3.6.1.4.1.164.3.1.6.4.1.3.1.6

dsx1IntervalFEBE

Far End Block Errors, as reported in the first bit
of frames 13 and 15, on multiframe E1 lines with CRC4,
in one of the previous 96, individual, 15 minute intervals.

PerfHist-TC-MIBPerfIntervalCount

Enumerated Values:

1	jtG704
2	ituG704

.1.3.6.1.4.1.164.3.1.6.4.1.3.1.7

dsx1IntervalStatus

OctetString

Enumerated Values:

2	oosCode
3	ais

.1.3.6.1.4.1.164.3.1.6.4.1.3.1.8

dsx1IntervalBPV

The counter associated with the number of BPV (Bi-Polar Violations)
encountered by a DS1 interface in one of the previous 96,
individual 15 minute, intervals.

PerfHist-TC-MIBPerfIntervalCount

.1.3.6.1.4.1.164.3.1.6.4.1.3.1.9

dsx1IntervalLOCRCMF

Loss of CRC4 Multi-Frame sequence in E1.

PerfHist-TC-MIBPerfIntervalCount

.1.3.6.1.4.1.164.3.1.6.4.1.3.1.10

dsx1IntervalLOFC

Counts the number of loss of frame events measured
in one of the previous 96, individual 15 minute, intervals.

PerfHist-TC-MIBPerfIntervalCount

Enumerated Values:

1	notApplicable
2	v35
3	x21
4	rs530
5	cisco
6	lapd
7	laps
8	proprietary
9	gfp

.1.3.6.1.4.1.164.3.1.6.4.1.3.1.11

dsx1XTotalTable

table

.1.3.6.1.4.1.164.3.1.6.4.1.4 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk dsx1XTotalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::dsx1XTotalTable'

A list of Total statistics entries.  This table
contains additional objects for the Total table.

dsx1XTotalEntry row .1.3.6.1.4.1.164.3.1.6.4.1.4.1

An entry containing additional statistical counters
applicable to a particular current table.

Indexes

No indexes recorded

Column Syntax OID

dsx1TotalLOS

The counter associated with the number of LOS (Loss of Signal)
seconds encountered by a DS1 interface in the previous
24 hour interval.
Invalid 15 minute intervals count as 0.

PerfHist-TC-MIBPerfTotalCount

Enumerated Values:

1	dce
2	dte

.1.3.6.1.4.1.164.3.1.6.4.1.4.1.1

dsx1TotalBPV

The counter associated with the number of BPV (Bi-Polar Violations)
encountered by a DS1 interface in the previous 24 hour interval.
Invalid 15 minute intervals count as 0.

PerfHist-TC-MIBPerfTotalCount

Enumerated Values:

1	notApplicable
2	internal
3	external
4	disable

.1.3.6.1.4.1.164.3.1.6.4.1.4.1.9

dsx1TotalLOFC

The counter associated with the number loss of frames
encountered by a DS1 interface in the previous 24 hour interval.
Invalid 15 minute intervals count as 0.

PerfHist-TC-MIBPerfTotalCount

Enumerated Values:

1	normal
2	inverse

.1.3.6.1.4.1.164.3.1.6.4.1.4.1.11

dsx1DataStreamStatTable

table

.1.3.6.1.4.1.164.3.1.6.4.1.5 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk dsx1DataStreamStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::dsx1DataStreamStatTable'

The DS1 Data Stream Statistics table.

dsx1DataStreamStatEntry row .1.3.6.1.4.1.164.3.1.6.4.1.5.1

An entry in the DS1 Data Stream Statistics table.

Indexes

No indexes recorded

Column Syntax OID

dsx1DataStreamStatIfIndex

The index of the DS1 interface.
It may be ifIndex.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	internal
3	external

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.4.1.5.1.1

dsx1DataStreamStatIndex

The DS1 Data Stream Index.
For Vmux - the following indices are used:
1 for Transparent
2-3 for SS71-SS72 (respectively)
4-7 for Data1-Data4 (respectively)
8 for HDLC Ph2 Compatible
9-16 for Sub-CH1-1...…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.4.1.5.1.2

dsx1DataStreamStatValid

Indicates whether this Data Stream is valid or not.
When invalid - all counters are irrelevant.

SNMPv2-TCTruthValue

Enumerated Values:

1	normal
2	inverse

Description:

Represents a boolean value.

.1.3.6.1.4.1.164.3.1.6.4.1.5.1.3

dsx1DataStreamStatInFrames

The counter associated with the number of received frames,
encountered by the DS1 Data Stream.

SNMPv2-SMICounter32

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.4.1.5.1.4

dsx1DataStreamStatInBytes

The counter associated with the number of received bytes,
encountered by the DS1 Data Stream.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.4.1.5.1.5

dsx1DataStreamStatInDiscards

The counter associated with the number of Discarded incoming frames,
encountered by the DS1 Data Stream.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.4.1.5.1.6

dsx1DataStreamStatInErrors

The counter associated with the number of received Errored frames,
encountered by the DS1 Data Stream.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.4.1.5.1.7

dsx1DataStreamStatOutFrames

The counter associated with the number of transmitted frames,
encountered by the DS1 Data Stream.

SNMPv2-SMICounter32

Constraints:
range: 4-4

.1.3.6.1.4.1.164.3.1.6.4.1.5.1.8

dsx1DataStreamStatOutBytes

The counter associated with the number of transmitted bytes,
encountered by the DS1 Data Stream.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.4.1.5.1.9

dsx1DataStreamStatOutDiscards

The counter associated with the number of Discarded outgoing frames,
encountered by the DS1 Data Stream.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.4.1.5.1.10

dsx1DataStreamStatOutErrors

The counter associated with the number of errored transmitted frames,
encountered by the DS1 Data Stream.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.4.1.5.1.11

dsx1XConfigTable

table

.1.3.6.1.4.1.164.3.1.6.4.2 · 1 row entry · 23 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk dsx1XConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::dsx1XConfigTable'

An extension to the DS1 Configuration table.

dsx1XConfigEntry row .1.3.6.1.4.1.164.3.1.6.4.2.1

An entry containing additional configuration
parameters.

Indexes

No indexes recorded

Column Syntax OID

dsx1IdleCode

Byte pattern of the data received/transmitted in the
E1T1 framer idle timeslots.
Valid range: (0 - FF HEX).

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.4.2.1.1

dsx1LineMode

T1 device operation mode.
Valid for T1 only.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.4.2.1.2

dsx1dBTxGain

Transmit line Gain for T1 CSU line mode.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.4.2.1.3

dsx1RxSensitivity

Low Sensitivity is considered Short Haul while High Sensitivity
is considered Long Haul. The actual values depend on the LIU.
Examples:
- E1: -12dB is considered Short Haul ; -43dB is considered Long Haul
- T1: -12dB i…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.4.2.1.4

dsx1RestoreTime

Used to change the sync. algorithms to reduce the time
required for the port to return to normal operation after
a RED alarm.
'sec1' = Fast,
'sec10' = TR-6211,
'immediate' = CCITT

Enumerationr/w

Constraints:
range: 1-96

.1.3.6.1.4.1.164.3.1.6.4.2.1.5

dsx1TcFirstSignal

Trunk conditioning signal - value to be sent as a signal
during the first 2.5 seconds after alarm detection.
Range is 0x0..0xF. 0xFF is a NULL value.
This variable is used also for Space Signaling Code (in this cas…

SNMPv2-SMIInteger32r/w

Constraints:
range: 4-4

.1.3.6.1.4.1.164.3.1.6.4.2.1.6

dsx1TcSignal

Trunk conditioning signal value after alarm detection.
Range is 0x1..0xF for E1, and 0x0..0xF for T1.
This variable is used also for Space Signaling Code (E1 and T1).

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.4.2.1.7

dsx1TcPattern

Trunk conditioning data pattern to be sent upon a DS0 fail.
Range is 0x0..0xFF.
This variable used also for Out of Service Code.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.4.2.1.8

dsx1Scramble

Scrambling is an operation that randomizes the bits
of the payload of the ATM cell by a polynom.
This operation helps with the error detection mechanism
of the HEC. Not applicable for E1.
active - will scramble/descram…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.4.2.1.9

dsx1LineAdaptiveTimingMode

Enables end to end clock synchronization.
Default value - off.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.4.2.1.10

dsx1TxClockSource

The source of Transmit Clock.
'loopTiming' indicates that the recovered receive clock
is used as the transmit clock.

'localTiming' indicates that a local clock
source is used or when an external clock …

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.4.2.1.11

dsx1AisEnable

Enable/ disable AIS transmit when Ethernet cable (for TDMoIP) is out (disconnected).

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.4.2.1.12

dsx1TsEchoCancel

This parameter defines for each TS whether Echo-Cancellation is on.
Each bit represents one TS as follow:
First octet bit'0' = TS#1, bit'7' = TS#8, .. 2nd octet bit'0' = TS#9,..,
4th octet bit'7' = TS#32.
Octets and bi…

OctetStringr/w

.1.3.6.1.4.1.164.3.1.6.4.2.1.13

dsx1EchoCancelerModule

This parameter indicates whether echo-cancellation module
exists for this line.

Enumeration

.1.3.6.1.4.1.164.3.1.6.4.2.1.14

dsx1PortFunction

This object determines the ATM Mode over the
physical port.
uni - The port will function as an ATM UNI.
ces - The port will function as a CES.
ima - The port will function as an IMA-ATM.
cesPsn - The port will…

Enumerationr/w

Enumerated Values:

1	meteringPulse1
2	meteringPulse2
3	initRinging1
4	initRinging2
237	normalBattery
250	noBattery
251	reducedBattery
254	reversePolarity
255	normalPolarity

.1.3.6.1.4.1.164.3.1.6.4.2.1.15

dsx1PortMultiplier

This object determines the data rate of each TS
(Kbps units).
This parameter is applicable for T1 only.

Enumerationr/w

Enumerated Values:

2	notValid
3	valid

.1.3.6.1.4.1.164.3.1.6.4.2.1.16

dsx1LeasedLine

This parameter defines whether Line mode is regular (non Leased Line mode)
or transparent (Leased Line mode).

Enumerationr/w

Constraints:
range: 0-31

.1.3.6.1.4.1.164.3.1.6.4.2.1.17

dsx1CsuLoop

This parameter defines where the CSU loop will be done:
local - locally (by IPmux) towards the TDM device
transparent - transferred to Remote Device that will send it to its
connected TDM device.
remote -…

Enumerationr/w

Constraints:
range: 0-990

.1.3.6.1.4.1.164.3.1.6.4.2.1.18

dsx1ClockSource

This entry specifies the source from which the clock will be taken.
Refer to device specification for source Index

SNMPv2-SMIInteger32r/w

Constraints:
range: 0-990

.1.3.6.1.4.1.164.3.1.6.4.2.1.19

dsx1OosSignal

This parameter defines the value to be sent as a signal
after alarm detection:
'Space' = both A and B signaling bits are forced
to '0' during out-of-service periods.
'Mark' = both A and B signaling bits a…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.4.2.1.20

dsx1BundleNextIndex

This parameter indicates the Next free Bundle Index for this DS1 port.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.4.2.1.21

dsx1CRC6CalcMode

This object determines the CRC6 Calculation mode.
jtG704 =JT-G704 = the Japanese standard
ituG704=ITU-G704 = the International standard
This parameter is applicable for J1 only.

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.6.4.2.1.22

dsx1SendUponFail

This object determines which notification will be sent to the other side
upon fail of another interface.
In Ipmux14 the notification is sent upon failure of the Ethernet link.

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.1.6.4.2.1.23

hdlcTable

table

.1.3.6.1.4.1.164.3.1.6.5.1 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk hdlcTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::hdlcTable'

The HDLC configuration table.

hdlcEntry row .1.3.6.1.4.1.164.3.1.6.5.1.1

Defines the contents of each line in the RAD HDLC Table.

Indexes

No indexes recorded

Column Syntax OID

hdlcProtocol

The HDLC protocol type
V35 - HDLC encapsulated over V35
X21 - HDLC encapsulated over X21
RS530 - HDLC encapsulated over RS530
cisco - Compatible to Cisco HDLC format.
lapd - LAPD over HDLC.
laps - LAPS over HDLC…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	ts15
3	ts16
4	ts31

.1.3.6.1.4.1.164.3.1.6.5.1.1.1

hdlcRateResolution

The baud rate of the internal clock.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	ts15
3	ts16
4	ts31

.1.3.6.1.4.1.164.3.1.6.5.1.1.2

hdlcTxClockSource

The baud rate of the internal clock.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.5.1.1.3

hdlcTerminalMode

Enumerationr/w

Enumerated Values:

1	notApplicable
2	notActive
3	active
4	activeReq

.1.3.6.1.4.1.164.3.1.6.5.1.1.4

hdlcLoopbackState

internal - All data coming from the
network port is looped back
external - All data comming from the line is
looped back.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	notValid
3	valid

.1.3.6.1.4.1.164.3.1.6.5.1.1.5

hdlcTxClockPolarity

normal - The transmitted data is sampled at the middle of bit time
inverse - The transmitted data is sampled at the end of the bit time
(high data rate/long cable).

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.5.1.1.6

hdlcFlowControl

Enable/Disable the CTS/RTS flow control signals.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.5.1.1.7

hdlcLineRate

The rate values for HDLC are n*56/64Kbps, where 1<=n<=32, 64, 128
and the following values: 1544, 3088, 6176.
The rate values for HSSI is nMbps, where 1<=n<=52.

SNMPv2-SMIInteger32r/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.6.5.1.1.8

hdlcRxClockMode

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.1.6.5.1.1.9

hdlcLOF

Total number of seconds the port is in Loss Of Frame state.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.5.1.1.10

hdlcRxClockPolarity

normal - The received data is sampled at the middle of bit time
inverse - The received data is sampled at the end of the bit time
(high data rate/long cable).

Enumerationr/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.1.6.5.1.1.11

hdlcRateCompatibility

This parameter defines whether limit the port HDLC rate according to the Far-End device.
For exaple: limit the HDLC rate from 4000 PPS and 3000 PPS.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.5.1.1.12

hdlcCurrentTable

table

.1.3.6.1.4.1.164.3.1.6.5.2.1 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk hdlcCurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::hdlcCurrentTable'

The HDLC Current table.

hdlcCurrentEntry row .1.3.6.1.4.1.164.3.1.6.5.2.1.1

An entry in the HDLC Current table.

Indexes

No indexes recorded

Column Syntax OID

hdlcCurrentIfIndex

The index of the HDLC interface.
It may be ifIndex.

SNMPv2-SMIInteger32

Constraints:
range: 0-65535

.1.3.6.1.4.1.164.3.1.6.5.2.1.1.1

hdlcCurrentStatus

OctetString

.1.3.6.1.4.1.164.3.1.6.5.2.1.1.2

hdlcCurrentLOF

The counter associated with the number of seconds the
port is in Loss Of Frame state, encountered
by the HDLC interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.5.2.1.1.3

hdlcCurrentInFrames

The counter associated with the number of received frames,
encountered by the HDLC interface in the current 15 minute
interval.

SNMPv2-SMIGauge32

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.5.2.1.1.4

hdlcCurrentInErrors

The counter associated with the number of Errored received
frames, encountered by the HDLC interface in the current 15
minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.5.2.1.1.5

hdlcCurrentOutFrames

The counter associated with the number of transmitted frames,
encountered by the HDLC interface in the current 15 minute
interval.

SNMPv2-SMIGauge32

Enumerated Values:

1	notUsed
2	normal
3	blockReqDenied
4	remoteBlocked
5	localBlocked
6	unblockReqDenied
7	duringBlock
8	duringUnblock
9	localLoop
10	remoteLoop
11	localUnblock
12	remoteUnblock

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.5.2.1.1.6

hdlcCurrentAbortedFrames

The counter associated with the number of frames, in which
at least seven consecutive '1'-s (Abort sequence) were
encountered by the HDLC interface in the current 15 minute
interval.

SNMPv2-SMIGauge32

Enumerated Values:

1	notApplicable
2	unBlock
3	block
4	blockRequest

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.5.2.1.1.7

hdlcCurrentLengthError

The counter associated with the number of received frames
with length error, encountered by the HDLC interface in the
current 15 minute interval.

SNMPv2-SMIGauge32

Enumerated Values:

1	notApplicable
2	no
3	yes

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.5.2.1.1.8

hdlcIntervalTable

table

.1.3.6.1.4.1.164.3.1.6.5.2.2 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk hdlcIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::hdlcIntervalTable'

The HDLC Interval table.

hdlcIntervalEntry row .1.3.6.1.4.1.164.3.1.6.5.2.2.1

An entry in the HDLC Interval table.

Indexes

No indexes recorded

Column Syntax OID

hdlcIntervalIfIndex

The index of the HDLC interface.
It may be ifIndex.

SNMPv2-SMIInteger32

Constraints:
range: 0-32

.1.3.6.1.4.1.164.3.1.6.5.2.2.1.1

hdlcIntervalNumber

A number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals exist).

Integer32

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.1.6.5.2.2.1.2

hdlcIntervalStatus

OctetString

Enumerated Values:

1	notApplicable
2	twoBits
3	fourBits
4	eightBits

.1.3.6.1.4.1.164.3.1.6.5.2.2.1.3

hdlcIntervalLOF

The counter associated with the number of seconds the
port is in Loss Of Frame state, encountered by an HDLC
interface in one of the previous 96, individual 15 minute,
intervals.

SNMPv2-SMIGauge32

Constraints:
range: 0-7

.1.3.6.1.4.1.164.3.1.6.5.2.2.1.4

hdlcIntervalInFrames

The counter associated with the number of received frames,
encountered by the HDLC interface in one of the previous 96,
individual 15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.5.2.2.1.5

hdlcIntervalInErrors

The counter associated with the number of Errored received
frames, encountered by the HDLC interface in one of the
previous 96, individual 15 minute, intervals.

SNMPv2-SMIGauge32

Enumerated Values:

1	notApplicable
2	notValid
3	valid

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.5.2.2.1.6

hdlcIntervalOutFrames

The counter associated with the number of transmitted
frames, encountered by the HDLC interface in one of
the previous 96, individual 15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.5.2.2.1.7

hdlcIntervalAbortedFrames

The counter associated with the number of frames, in which
at least seven consecutive '1'-s (Abort sequence) were
encountered by the HDLC interface in one of the previous 96,
individual 15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.5.2.2.1.8

hdlcIntervalLengthError

The counter associated with the number of received frames
with length error, encountered by the HDLC interface in
one of the previous 96, individual 15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.5.2.2.1.9

nplPulseTable

table

.1.3.6.1.4.1.164.3.1.6.6.1.1.4 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk nplPulseTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::nplPulseTable'

NPL Pulse table. This table is written directly to the agent.

nplPulseEntry row .1.3.6.1.4.1.164.3.1.6.6.1.1.4.1

An entry in table nplPulseTable.

Indexes

No indexes recorded

Column Syntax OID

nplPulseType

Pulse Type

Enumeration

Constraints:
range: 1-8

.1.3.6.1.4.1.164.3.1.6.6.1.1.4.1.1

nplPulseValid

Validity of the Pulse Type.

Enumerationr/w

Enumerated Values:

2	none
3	primary
4	secondary
5	regular
6	standby

.1.3.6.1.4.1.164.3.1.6.6.1.1.4.1.2

nplPulseDurationType

Pulse Duration Type.
- If meteringPulse1 and meteringPulse2 are both 'valid', the value of this
object must be different for them.
- If initRinging1 and initRinging2 are both 'valid', the value of this
object must…

Integer32r/w

.1.3.6.1.4.1.164.3.1.6.6.1.1.4.1.3

nplPulseOnTime

How much time the pulse is ON, in msec.
0 is a valid value only when nplPulseValid=notValid.

Integer32r/w

Constraints:
range: 0-65535

.1.3.6.1.4.1.164.3.1.6.6.1.1.4.1.4

nplPulseOffTime

How much time the pulse is OFF, in msec.

Integer32r/w

.1.3.6.1.4.1.164.3.1.6.6.1.1.4.1.5

v51VarTable

table

.1.3.6.1.4.1.164.3.1.6.6.2.1 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk v51VarTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::v51VarTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

v51VarEntry row .1.3.6.1.4.1.164.3.1.6.6.2.1.1

An entry in table v51VarTable.

Indexes

No indexes recorded

Column Syntax OID

v51VarCnfgIdx

This attribute indicates the Idx of the Cnfg being accessed.
255 = TmpCnfg.
1 = Current Cnfg.
Write is allowed only to TmpCnfg.

Integer32

.1.3.6.1.4.1.164.3.1.6.6.2.1.1.1

v51VarSltIdx

Slot Index.
For V5.2, this index will be the Slot of the V5.2 Master ML.

Enumeration

.1.3.6.1.4.1.164.3.1.6.6.2.1.1.2

v51VarPrtIdx

This attribute indicates a unique port number of the ML having
V5 interface.
Valid values: exPrt1 (1)..exPrt4 (4), inPrt1(101)..inPrt4(104),
notApplicable(255) - for V5.2 only.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.6.2.1.1.3

v51VarIdx

Variant Id.
Valid values:
- for Current Cnfg: 0..127
- for Tmp Cnfg: until MP R9 : 255 only.
from MP R10: 0..127.

Integer32

.1.3.6.1.4.1.164.3.1.6.6.2.1.1.4

v51VarPstnCch

This object indicates which TS will be used for PSTN C channel.
For V5.2 - notApplicable.

Enumerationr/w

Enumerated Values:

1	nc
2	pstn
3	isdnB1
4	isdnB2
5	cChannel
6	permanentB1
7	permanentB2
8	semiPermanentB1
9	semiPermanentB2

.1.3.6.1.4.1.164.3.1.6.6.2.1.1.5

v51VarIsdnSTypeCch

This object indicates which TS will be used for S-Type C channel.
For V5.2 - notApplicable.

Enumerationr/w

Constraints:
range: 0-65535

.1.3.6.1.4.1.164.3.1.6.6.2.1.1.6

v51VarDescription

This object describes the Variant.

SNMPv2-TCDisplayStringr/w

Enumerated Values:

1	notUsed
2	normalOperation
5	block
11	localUnblock
12	remoteUnblock

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.1.6.6.2.1.1.7

v51VarStatus

This object reports the status of an existing Variant of a link.
notActive - the variant exists on this link but is not active
active - the variant exists on this link AND is active
activeReq - the variant exists on …

Enumeration

.1.3.6.1.4.1.164.3.1.6.6.2.1.1.8

v51VarRowStatus

This object enables to create new entries and delete existing entries
from the table. It is applicable only from MP R10.

Enumerationr/w

Enumerated Values:

1	empty
2	outOfService
3	deactive
4	actInit
5	accessAct
6	plActInit
7	plAct
8	loopback2
9	loopback1
10	loopback1A
11	null
12	pathInit
13	pathAbortReq
14	lineInfo
15	pathActive
16	blocked
17	disconnectReq

.1.3.6.1.4.1.164.3.1.6.6.2.1.1.9

v51VarCfgTable

table

.1.3.6.1.4.1.164.3.1.6.6.2.2 · 1 row entry · 24 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk v51VarCfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::v51VarCfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

v51VarCfgEntry row .1.3.6.1.4.1.164.3.1.6.6.2.2.1

An entry in table v51VarCfgTable.

Indexes

v51MlSltIdx v51MlPrtIdx

Column Syntax OID

v51VarCfgIndex

This attribute indicates the Idx of the Cnfg being accessed.
255 = TmpCnfg.
1 = Current Cnfg.

Integer32

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.1

v51VarCfgSltIdx

Slot Index.
For V5.2, this index will be the Slot of the V5.2 Master ML.

Enumeration

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.2

v51VarCfgPrtIdx

This attribute indicates a unique port number of the ML having
V5 interface.
Valid values: exPrt1 (1)..exPrt4 (4), inPrt1(101)..inPrt4(104)
notApplicable(255) - for V5.2 only.

SNMPv2-SMIInteger32

Constraints:
range: 0-128

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.3

v51VarCfgIdx

Variant Id.
Valid values:
- for Current Cnfg: 0..127
- for Tmp Cnfg: until MP R9 : 255 only.
from MP R10: 0..127.

Integer32

Constraints:
range: 0-128

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.4

v51VarCfgTsIdx

For V5.1: Time Slot index (1..31).
For V5.2: Running Index (1..1320) for Address Table.

SNMPv2-SMIInteger32

Enumerated Values:

1	sysStartUp
2	waitForVarId
3	activatePstn
4	restart1
5	inService
6	restart2
7	restart3
8	waitV5Init
9	switchOver
10	ctrlDataLinkRel1
11	ctrlDataLinkRel2
12	ctrlDataLinkRel3
13	outOfService
14	waitE1Reports
15	waitL2StartUp
16	waitLinkId
17	waitRestart
18	notDefined

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.5

v51VarCfgTsType

Time Slot Type.

Enumerationr/w

Constraints:
range: 0-127

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.6

v51VarCfgPrtId

This object indicates the IO Port Id this TS is connected to.
For V5.2, the Port Id is a concatenation of SS:PP:TS of the port
connected to V5.2 Master.
SS=IO Slot (1..12)
PP=Port (01..16)
TS = TS (00 for ports tha…

Integer32r/w

Constraints:
range: 0-127

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.7

v51VarCfgEfL3Addr

This object indicates the Address of the IO port this TS is connected to.
The IO port is identified according to its Address:
- for ISDN ports: EF Address. Valid values: 0..8175
- for PSTN ports: L3 Address. Valid valu…

Integer32r/w

Constraints:
range: 0-127

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.8

v51VarCfgFTypeCch

For V5.1 - this object indicates which TS will be used for F-Type C channel.
notApplicable (1),
ts15 (2),
ts16 (3),
ts31 (4)
For V5.2 - this object indicates the Logical C Channel F Typ…

SNMPv2-SMIInteger32r/w

Constraints:
range: 0-127

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.9

v51VarCfgPTypeCch

For V5.1 - This object indicates which TS will be used for P-Type C channel.
notApplicable (1),
ts15 (2),
ts16 (3),
ts31 (4)
For V5.2 - this object indicates the Logical C Channel P Typ…

SNMPv2-SMIInteger32r/w

Constraints:
range: 0-127

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.10

v51VarCfgConSlt

The Slot containing the IO port this TS is connected to.
For V5.2 this object is notApplicable.

Enumeration

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.11

v51VarCfgConPrt

The IO Port this TS is connected to.
Valid values: exPrt1 (1)..exPrt12 (12), inPrt1(101)..inPrt4(104).
100=noConnect
For V5.2 this object is notApplicable=255.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.12

v51VarCfgIoState

The State of the IO port this TS is connected to.
This object is not applicable for v51VarCfgIndex=255=TmpCnfg.
normal(2) - will be used for operating normally (operate)
localBlocked(5) - will be used for general Block …

Enumeration

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.13

v51VarCfgBlock

This object indicates if this TS will be Blocked or not and how:
block - done locally
blockRequest - according to external request of the telephone exchange.

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.14

v51VarCfgExtDch

For V5.1: This object indicates if this TS is an ISDN D channel that
comes via Bypass from a non-V5.1 ML.
For V5.2: this object will be notApplicable (not supported).

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.15

v51VarCfgExtDchSlot

This object is applicable only if v51VarCfgExtDch=yes(3).
It indicates the Slot of the non-V5.1 ML on which the External D channel
TS is defined (and is transferred via Bypass between the V5.1 ML and
the non-V5.1 ML.)
N…

Enumerationr/w

Constraints:
range: 0-99999999

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.16

v51VarCfgExtDchPort

This object is applicable only if v51VarCfgExtDch=yes(3).
It indicates the Port on the Slot of 'v51VarCfgExtDchSlot' of the
non-V5.1 ML on which the External D channel TS is defined (and is
transferred via Bypass betw…

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	sync
3	async

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.17

v51VarCfgExtDchTs

This object is applicable only if v51VarCfgExtDch=yes(3).
It indicates the TS on the non-V5 ML on which the External
D channel TS is defined (and is transferred via Bypass between
the V5 ML and the non-V5 ML.)
For V5.…

Integer32r/w

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.18

v51VarCfgExtDchCmpr

For V5.1 - this object is applicable only if v51VarCfgExtDch=yes(3).
It indicates if this ISDN D channel TS is Compressed or not.

Enumerationr/w

Enumerated Values:

2	disabled
3	enabled

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.19

v51VarCfgExtDchRate

For V5.1 - this object is applicable only if v51VarCfgExtDch=yes(3).
It indicates the Rate of the ISDN D channel.

Enumerationr/w

Enumerated Values:

2	uponLeRestart
3	uponPstnProtocolAck

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.20

v51VarCfgExtDchStartBit

For V5.1 - this object is applicable only if v51VarCfgExtDch=yes(3).
It indicates the Start Bit of the ISDN D channel on the TS of
the non-V5.1 ML on which it is defined.
Valid values:
- for v51VarCfgExtDchRate…

Integer32r/w

Enumerated Values:

1	notApplicable
2	none
3	endPoint
4	exchangePoint

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.21

v51VarCfgSTypeCch

This object is supported only by V5.2. It indicates the Logical
C Channel S Type (0..65535).
65536=not applicable.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.22

v51VarCfgStatus

This object is supported only by V5.2.
It enables to create new entries and delete existing entries
from the table.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.23

v51VarCfgV52MasterTsa

This object is supported only by V5.2.
This will be the V5.2 Master, Switch Allocated Location. It is
a concatenation of SS:PP:TS of the V5.2 Master.
It indicates which is the exact port and TS allocated by the Loca…

SNMPv2-SMIInteger32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.6.6.2.2.1.24

v5VarCchTable

table

.1.3.6.1.4.1.164.3.1.6.6.2.3 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk v5VarCchTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::v5VarCchTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

v5VarCchEntry row .1.3.6.1.4.1.164.3.1.6.6.2.3.1

An entry in table v5VarCchTable.

Indexes

No indexes recorded

Column Syntax OID

v5VarCchCfgIndex

This attribute indicates the Idx of the Cnfg being accessed.
255 = TmpCnfg.
1 = Current Cnfg.

Integer32

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.1.6.6.2.3.1.1

v5VarCchVarIdx

Variant Id.
Valid values: 0..127.

Integer32

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.1.6.6.2.3.1.2

v5VarCchIdx

C-CH Id.
There are only 8 possible C-CHs per Variant.

Integer32

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.1.6.6.2.3.1.3

v5VarCchType

C-CH Type.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.6.2.3.1.4

v5VarCchPhyLinkNo

The Physical Link Number of the card (1..4).
This object is applicable only if v51VarCchType is not 'none'.
notApplicable=255.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.6.2.3.1.5

v5VarCchLogicalId

The Logical C-CH Id. (0..65535)
When v51VarCchType is 'none', this object is irrelevant.

Integer32r/w

.1.3.6.1.4.1.164.3.1.6.6.2.3.1.6

v5VarCchTs

The C-CH TS. Valid values: 16, 15, 31.
If v51VarCchType=primary or secondary, the value must be 16 (RO).
This object is applicable only if v51VarCchType is not 'none'.
notApplicable=0.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.6.2.3.1.7

v5VarCchPstn

PSTN C-CH.
Only one entry can have the value 'yes'.
notApplicable - when v51VarCchType is none, secondary or standby.

Enumerationr/w

Enumerated Values:

2	down
3	up
4	disabled
5	remoteFail
6	localFail
7	unavailable
8	validationFail
9	standby
10	tdmFail
11	hwMismatch

.1.3.6.1.4.1.164.3.1.6.6.2.3.1.8

v5VarCchIsdnTypes

ISDN Types of C-CH.
This object is a sum of 2**n, where n=Bit No. and Bit is '1':
Bit No. ISDN Type
0 P
1 F
2 S
Bit value '1'= Yes
Bit value '0'= No
Example…

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	down
3	up

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.6.2.3.1.9

v5VarStatTable

table

.1.3.6.1.4.1.164.3.1.6.6.2.4 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk v5VarStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::v5VarStatTable'

This is a RO table. It includes only the Active Addresses of
the Active Variant, their minimal Config data and Status.

v5VarStatEntry row .1.3.6.1.4.1.164.3.1.6.6.2.4.1

An entry in table v5VarStatTable.

Indexes

No indexes recorded

Column Syntax OID

v5VarStatIdx

Running Index (1..120). Up to 120 calls can be active at the same time
on the Active Variant.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.6.2.4.1.1

v5VarStatPrtId

This object indicates the IO Port Id, the Address is connected to.
The Port Id is a concatenation of SS:PP:TS of the port connected
to an Address of the Active Variant running on the V5.2 Master card.
SS=IO Slot (1..12…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.6.2.4.1.2

v5VarStatPortType

Address Port Type.

Enumeration

.1.3.6.1.4.1.164.3.1.6.6.2.4.1.3

v5VarStatEfL3Addr

This object indicates the EF/L3 Address of the IO port this entry
is connected to.
The IO port is identified according to its EF/L3 Address:
- for ISDN ports: EF Address. Valid values: 0..8175
- for PSTN ports: L3 Add…

Integer32

.1.3.6.1.4.1.164.3.1.6.6.2.4.1.4

v5VarStatPortState

The State of the IO port this Address entry is connected to.
The values were designed to match the relevant values of v51VarCfgIoState.

Enumeration

.1.3.6.1.4.1.164.3.1.6.6.2.4.1.5

v5VarStatMasterTsa

This will be the V5.2 Master Switch Allocated TSA Location. It is
a concatenation of SS:PP:TS of the V5.2 Master card.
It indicates which is the exact port and TS allocated by the Local
Exchange on the V5.2 Link.
…

SNMPv2-SMIInteger32

Enumerated Values:

2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.6.2.4.1.6

v5VarStatCallState

Call State of the Address.

Enumeration

.1.3.6.1.4.1.164.3.1.6.6.2.4.1.7

v51MlTable

table

.1.3.6.1.4.1.164.3.1.6.6.3.1.1 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk v51MlTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::v51MlTable'

Variant Command and Status table.

v51MlEntry row .1.3.6.1.4.1.164.3.1.6.6.3.1.1.1

An entry in table v51MlTable.

Indexes

No indexes recorded

Column Syntax OID

v51MlSltIdx

Slot Index.
For V5.2 this index is notApplicable.

Enumeration

.1.3.6.1.4.1.164.3.1.6.6.3.1.1.1.1

v51MlPrtIdx

This attribute indicates a unique port number of the ML having
V5 interface.
Valid values: exPrt1 (1)..exPrt4 (4), inPrt1(101)..inPrt4(104),
notApplicable(255) - for V5.2 only.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.6.3.1.1.1.2

v51MlCurrActiveVar

For V5.1: the currently Active Variant Id. on this ML.
For V5.2: the currently Active Variant Id.
128=none.

Integer32

.1.3.6.1.4.1.164.3.1.6.6.3.1.1.1.3

v51MlLeActiveReqVar

For V5.1: the Variant Id. that the Local Exchange (LE)
requested to be Active on this ML.
For V5.2: the Variant Id. that the Local Exchange (LE)
requested to be Active.
128=none.

Integer32

.1.3.6.1.4.1.164.3.1.6.6.3.1.1.1.4

v51MlProtocolState

Protocol State of the ML Active Variant.
- sysStartUp - an Establish request arrived to the V5.1 interface.
- waitForVarId - the variant and the Interface Id were requested
during the system start-up…

Enumeration

Enumerated Values:

1	notApplicable
2	static
3	dynamicLES
4	dynamicCAS
5	cesOverIp
6	voiceOverMpls
7	hdlc
8	voIpComprHeader
9	voMplsComprHeader
10	satop
11	cesOverPsn
12	hdlcOverPsn

.1.3.6.1.4.1.164.3.1.6.6.3.1.1.1.5

v51MlUserActiveVarReq

User Request to turn a certain Variant of the ML, to Active.
This object specifies the Variant Id. requested by user to be Active.
User's request is not always accepted.

Integer32r/w

Constraints:
range: 0-899

.1.3.6.1.4.1.164.3.1.6.6.3.1.1.1.6

v51MlDeleteVarReq

For V5.1: User Request to Delete a certain Variant of the ML.
For V5.2: User Request to Delete a certain Variant
This object specifies the Variant Id. requested by user to be Delete.
User's request will not be accepted …

Integer32r/w

Constraints:
range: 0-96

.1.3.6.1.4.1.164.3.1.6.6.3.1.1.1.7

v51MlSaveVariant

User Command to Save the TmpCnfg Variant data to a certain Variant Id of
the selected ML, in Current Cnfg. The value of this object specifies
the target Variant Id.
The data transferred should be:
- for V5.1: v51…

Integer32r/w

Enumerated Values:

1	notApplicable
2	e1
3	t1Esf
4	t1D4
5	fxs
6	serialLink
7	t1Unframed

.1.3.6.1.4.1.164.3.1.6.6.3.1.1.1.8

v51MlReadVariant

User Command to Read data from a certain Variant Id of the selected ML,
(in Current Cnfg) to the TmpCnfg. The value of this object specifies
the source Variant Id.
The data transferred should be:
- for V5.1: v51Va…

Integer32r/w

Enumerated Values:

1	notApplicable
2	none
3	primary
4	secondary

.1.3.6.1.4.1.164.3.1.6.6.3.1.1.1.9

v51MlDeactivateVar

User Request to Deactivate a certain Variant of the ML.
This object specifies the Variant Id. requested by user to be Deactivated.
User can deactivate a variant having Active Request status or Active
status. Deactivatin…

Integer32r/w

.1.3.6.1.4.1.164.3.1.6.6.3.1.1.1.10

v51MlCnfgTable

table

.1.3.6.1.4.1.164.3.1.6.6.3.2.1 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk v51MlCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::v51MlCnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

v51MlCnfgEntry row .1.3.6.1.4.1.164.3.1.6.6.3.2.1.1

An entry in table v51MlCnfgTable.

Indexes

No indexes recorded

Column Syntax OID

v51MlCnfgIdx

This attribute indicates the Idx of the Cnfg being accessed.
1..10 = Current Cnfg (data will be the same for all Current
Configurations)
255 = TmpCnfg.

Integer32

Enumerated Values:

1	notApplicable
2	data
3	voice
4	voiceAndCas

.1.3.6.1.4.1.164.3.1.6.6.3.2.1.1.1

v51MlCnfgSltIdx

Slot Index.
For V5.2 this index will be notApplicable(255).

Enumeration

Enumerated Values:

1	notApplicable
2	v1
3	v2

.1.3.6.1.4.1.164.3.1.6.6.3.2.1.1.2

v51MlCnfgPrtIdx

This attribute indicates a unique port number of the ML having
V5 interface.
Valid values: exPrt1 (1)..exPrt4 (4), inPrt1(101)..inPrt4(104)
NA=255 (for V5.2 only).

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.6.3.2.1.1.3

v51MlCnfgIfId

V5.1 Interface Id.

Integer32r/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.1.6.6.3.2.1.1.4

v51MlCnfgStartupMode

Startup Mode.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.6.3.2.1.1.5

v51MlCnfgReprovision

Reprovision Support.
- no : no reprovision support (=default)
- yes: reprovision is supported.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.6.3.2.1.1.6

v51MlCnfgUnblockIoPorts

Unblock IO Ports on Startup.
- disabled - disable sending Unblock request on restart
- enabled - request unblock of all IO ports ON RESTART (=default).

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.1.6.6.3.2.1.1.7

v51MlCnfgRestartComplete

Send Restart Complete.
- uponLeRestart - after receiving restart from the other side.
- uponPstnProtocolAck - after receiving restart ack from PSTN
protocol (=default).

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.6.3.2.1.1.8

v51MlCnfgV52Application

The V5.2 Application of the Mux.
notApplicable - for Agents that don't support this object.
none - V5.2 is not used in the Mux.
endPoint - this V5.2 Application transfers voice of Analog Voice
…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.1.6.6.3.2.1.1.9

v51IoCnfgTable

table

.1.3.6.1.4.1.164.3.1.6.6.4.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk v51IoCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::v51IoCnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

v51IoCnfgEntry row .1.3.6.1.4.1.164.3.1.6.6.4.1.1

An entry in table v51IoCnfgTable.

Indexes

No indexes recorded

Column Syntax OID

v51IoCnfgIdx

This attribute indicates the Idx of the Cnfg being accessed.
1..10 = Current Cnfg (data will be the same for all Current
Configurations)
255 = TmpCnfg.

Integer32

.1.3.6.1.4.1.164.3.1.6.6.4.1.1.1

v51IoCnfgSltIdx

Slot Index

Enumeration

.1.3.6.1.4.1.164.3.1.6.6.4.1.1.2

v51IoCnfgPrtIdx

This attribute indicates a unique port number of the Io having
V5 interface.
Valid values: exPrt1 (1)..exPrt16 (16)

SNMPv2-SMIInteger32

Enumerated Values:

2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.6.4.1.1.3

v51IoCnfgSType

This object indicates if S Type Signaling will be used by this ISDN port
(yes/no).
notApplicable - for PSTN ports.

Enumerationr/w

Enumerated Values:

1	aLAW
2	uLAW

.1.3.6.1.4.1.164.3.1.6.6.4.1.1.4

v51IoCnfgFType

This object indicates if F Type Signaling will be used by this ISDN port
(yes/no).
notApplicable - for PSTN ports.

Enumerationr/w

Enumerated Values:

2	disable
3	enable

.1.3.6.1.4.1.164.3.1.6.6.4.1.1.5

v51IoCnfgPType

This object indicates if P Type Signaling will be used by this ISDN port
(yes/no).
notApplicable - for PSTN ports.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.6.4.1.1.6

ip2IfTable

table

.1.3.6.1.4.1.164.3.1.6.7.1 · 1 row entry · 93 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ip2IfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ip2IfTable'

Channels Configuration Table.

ip2IfEntry row .1.3.6.1.4.1.164.3.1.6.7.1.1

Application layer configuration per link

Indexes

No indexes recorded

Column Syntax OID

ip2IfChannelIndex

The channel index, which is actualy the bundle ID.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	ip
3	mplsEth
4	mac
5	ipComprHeader
6	mplsComprHeader
7	udp

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.1

ip2IfRowStatus

This parameter allows NMS to create/delete entries of this table.

SNMPv2-TCRowStatusr/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

Description:

.1.3.6.1.4.1.164.3.1.6.7.1.1.2

ip2IfOperStatus

The actual link status.
remoteFail - No Rx.
localFail - No Tx.
unavailable - No echo replay or replay with invalid code or when connection is in Test state.
valiodationFail - Connection is in not valid state.
standby -…

Enumeration

.1.3.6.1.4.1.164.3.1.6.7.1.1.3

ip2IfAdminStatus

The desired state of the link.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.1.6.7.1.1.4

ip2IfDestAddr

The destination IP address.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.1.6.7.1.1.5

ip2IfNextHop

The next hop to which the frame should be sent.
Default value - 0.0.0.0.
Upon setting the default value the frame is sent
to the default Gateway.

RFC1155-SMIIpAddressr/w

Constraints:
range: 0-7

.1.3.6.1.4.1.164.3.1.6.7.1.1.6

ip2IfDestPort

The destination Bundle at the far-end device.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.7

ip2IfMacAddr

The Destination MAC address of the next hop or
destination station.

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.3.1.6.7.1.1.8

ip2IfJitterBuffer

The maximum cell arrival jitter in 10 usec that the
reassembly process will tolerate in the cell stream,
without producing errors on the CBR service interface.

For KM2100:
KML.11 - The range that w…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	ipAddress
3	macAddress

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.9

ip2IfTos

The TOS (Type of Service) value: 0..255.

In Vmux-2100/110 devices versions 3.1 and up, in Vmux-210 and in Vmux-4x0:
LSB 8 bits - 00 00 00 XX will be used for Signaling packets TOS.
N…

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	low
3	high
4	off

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.10

ip2IfTDMBytesInFrame

The number of TDM bytes to be placed in a single IP
frame payload.
For ip2IfTDMoIpMode = cesOverPsn this parameter indicates
the number of IP frames, calculated as: 1440/<Number of Timeslots>.

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	accurateness
3	constantDelay

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.11

ip2IfVlanSupport

VLAN support (Tagging).
no - No support to VLAN.
yes - 4 VLAN bytes will be added to the frame.

Enumerationr/w

Enumerated Values:

2	tdmOIpCe
3	tdmOIpCv

.1.3.6.1.4.1.164.3.1.6.7.1.1.12

ip2IfVlanIdentifier

VLAN ID.

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.13

ip2IfVlanFramePriority

VLAN Frame priority.

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.14

ip2IfExitPort

This object determines to which external port the traffic
will be sent.
auto - the device will decide automatically the exit port.
If there is an option for Tx via more than one ETH card then use ext1 (1) and ext2(2)
f…

Enumerationr/w

Enumerated Values:

2	disable
3	enable

.1.3.6.1.4.1.164.3.1.6.7.1.1.15

ip2IfVoiceOos

Voice Out-Of-Service code. Valid range: (0 - FF HEX).
For agents that do not support this feature, the value will
always be 0.

OctetStringr/w

Enumerated Values:

2	rate12Khz
3	rate16Khz

.1.3.6.1.4.1.164.3.1.6.7.1.1.16

ip2IfDataOos

Data Out-Of-Service code. Valid range: (0 - FF HEX).
For agents that do not support this feature, the value will
always be 0.

OctetStringr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.17

ip2IfBundleUsage

The Bundle Resource usage in Kbps.

SNMPv2-SMIInteger32

Enumerated Values:

2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.18

ip2IfOAM

This parameter determine the OAM configuration.
The LSB (Bit 0 the most right one) is used for OAM connectivity.
Values: 0 = disable, 1= enable.

OctetStringr/w

Enumerated Values:

2	disable
3	enable

.1.3.6.1.4.1.164.3.1.6.7.1.1.19

ip2IfTDMoIpMode

The TDMoIP Mode configuration. Static- means TS can Tx any time.
dynamicLES - means TS can Tx only when line is enabled according to LES protocol.
dynamicCAS - means TS can Tx only when line is enabled according to CAS …

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.20

ip2IfTimeElapsed

The number of seconds that have elapsed since
the beginning of the current error-measurement period.
If, for some reason, such as an adjustment in the
system's time-of-day clock, the current interval exceeds
the maxim…

Integer32

.1.3.6.1.4.1.164.3.1.6.7.1.1.21

ip2IfValidIntervals

The number of previous intervals for which data was collected.
The value will be 96 unless the interface was brought online within
the last 24 hours, in which case the value will be
the number of complete 15 minute in…

Integer32

.1.3.6.1.4.1.164.3.1.6.7.1.1.22

ip2IfFarEndType

This object defines the type of the Far-End device.
This data is important for signaling and DS0 format.

For Vmux: e1 (2) value is used for a PBX in the Far End.
fxs (5) is used for Phone.
…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	f1780Hz
3	f2000Hz
4	f1780Plus2000Hz

.1.3.6.1.4.1.164.3.1.6.7.1.1.23

ip2IfRdnState

This object defines the role this bundle plays in the redundancy scheme:
none(2) - means this bundle is not part of redundancy pair.
primary/ secondary - means this bundle is not part of redundancy pair,
and that is the…

Enumeration

Enumerated Values:

2	proprietary
3	internalITUT

.1.3.6.1.4.1.164.3.1.6.7.1.1.24

ip2IfSourceAddr

Source IP Address of the bundle.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.1.6.7.1.1.25

ip2IfBandWidth

Defines the Bandwidth of the bundle.

For TDM bundles - it is the Number of Time Slots in The Bundle.
- For T1 the value will be: 1..24
- For E1 the value will be: 1..31
- For T3 the value will be: 1..84
…

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	bellcoreType1
3	v23

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.26

ip2IfMeasuredSilence

This object shows the percentage of Silence that was measured by the device
for the current bundle in the transmitted payload.
Relevant values: 0..100, 255.
Default value is 50.
0 means that there is no silence on the l…

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	ipAddress
3	macAddress

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.27

ip2IfPayloadType

This object defines the TDMoIP payload type.

Enumerationr/w

Enumerated Values:

2	r64KbpsIn5msecIntervalsG711
3	r64KbpsIn10msecIntervalsG711
4	r32KbpsG726
5	r24KbpsG726

.1.3.6.1.4.1.164.3.1.6.7.1.1.28

ip2IfProtocolVersion

This object defines the TDMoIP protocol Version.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.1.6.7.1.1.29

ip2IfTdmBackUpNextHop

Defines the TDM bundle default router in case there was a switch from the Primary Link
(for example an ETH port) to a TDM backup Link like E1, T1 or Serial Link.
This parameter is relevant only when a Backup Link is con…

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.1.6.7.1.1.30

ip2IfOosTxEnable

This object defines whether OOS will be Transmitted.
Note that for IPmux1000 the Lbit is always sent,
but the OOS will be sent according to user selection in this parameter.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.31

ip2IfConnCheckPktFrequency

Time in sec. between 2 Bundle Connectivity Check packets.
Valid values: 0..60. 0 = Not Applicable.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.32

ip2IfConnPktTimeOutCycles

No. of cycles the agent will send Bundle Connectivity packets without receiving
a response from the remote device before declaring that the bundle connection
to the remote side is down - Time Out.
Valid values: 0..5. 0 …

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	delaySensitive
3	dataSensitive

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.33

ip2IfMfRelay

Multi Frequency Signaling Detection.

Enumerationr/w

Enumerated Values:

2	bundleNumber
3	vccvCtrlWord

.1.3.6.1.4.1.164.3.1.6.7.1.1.34

ip2IfTxGain

Transmit gain in dBm.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.35

ip2IfSuperTandem

The Super Tandem feature provides end to end compression over multiple hops,
solving the double compression problem detected in Voice compressing systems.
The Super Tandem allows transmission of compressed voice between…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.36

ip2IfSrcPort

The source Bundle at the local device,
this parameter used for cases where there is no match
between ip2IfChannelIndex and the Source Bundle ID.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.37

ip2IfModemCalls

This MIB object shows whether Modem Calls are enabled via the bundle.
relay option (3) means that the bundle will send to the network only
modulated data.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.38

ip2IfMinPulseWidth

Indicates the minimum width in milliseconds of the MF (Multi Frequency)
tone transmitted by the switch.
Valid values: 45-300 msec.
notApplicable=0.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.39

ip2IfMinPowerLevel

Indicates the minimum power level in dBm of the MF (Multi Frequency)
tone transmitted by the switch.
Valid values: -1...-35 dBm.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.40

ip2IfEchoCanceler

Echo canceler activation.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.41

ip2IfCodingLaw

This attribute indicates the Method/Law for decoding/encoding the voice
information.
aLaw(1) is the standard Law for E1 links.
uLaw(2) is the standard Law for T1 links.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.42

ip2IfCustomToneDetect

Custom Tone Detection (COT) is a Control operation of a 2Khz tone detector.
This tone is sent between PBX devices in order to check that the line status
is OK. When the COT is enabled the device will not compress/decomp…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.43

ip2IfCallerIdDelay

Time in msec between CLID (Caller ID) signal detection on the line and CLID
signal transmission. The CLID must be sent between ringing signals and the value
of the delay is used for synchronizing the CLID transmission w…

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	srcPort
3	destPort

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.44

ip2IfConnectivityMode

This MIB object shows whether to send Pings or OAM frames over the bundle.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.1.6.7.1.1.45

ip2IfClockSourceEnable

This MIB object defines whether this bundle can be a clock source.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.1.6.7.1.1.46

ip2IfNetworkType

This MIB object defines the network over which the
Bundle PSN (Packet Switching Network)is transported.
In Gmux2000:
ipComprHeader indicates proprietary compressed IP header packets.
mplsComprHeader indicates proprieta…

Enumerationr/w

Enumerated Values:

1	notApplicable
3	forcedIdle
4	forcedBusy

.1.3.6.1.4.1.164.3.1.6.7.1.1.47

ip2IfMplsRxLabelEnable

This MIB object defines whether there is user defined
inner (Rx.) label for this Bundle.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.48

ip2IfMplsRxLabel

This MIB object defines the MPLS Rx. Label for this Bundle.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.49

ip2IfMplsTxLabelEnable

This MIB object defines whether there is user defined
outer (Tx.) label for this Bundle.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.50

ip2IfMplsTxLabel

This MIB object defines the MPLS Tx. Label for this Bundle.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.51

ip2IfMplsTxExpBits

The MPLS Network priority (EXP bits) used for this bundle.

Integer32r/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.52

ip2IfMfcSpoofing

This MIB object defines whether the MFC (Multi Frequency Compelled) protocol
spoofing will exist in the bundle. When the MFC Spoofing is used, the Local
and Remote PBXs will send MFC Signaling to each other. The Vmuxes …

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.53

ip2IfToneAckInterval

Time Interval in milli seconds from the time a Vmux sends tone/s to a local PBX until
it receives an acknowledgement from this PBX.
Valid values: 60...400 in steps of 20.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.54

ip2IfNextHopType

This MIB object defines the Bundle next Hop Address Type.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.55

ip2IfNoiseLevelForVAD

This object defines the Level of Noise on the line,
the Voice Activation Detector (VAD) will have to handle.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.56

ip2IfClockPreferences

The Clock preferences:
accurateness (2) = Accurate clock is more important than Constant Delay.
constantDelay (3)= Constant Delay is more important than Accurate clock .

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.57

ip2IfConnectionMode

The Connection Mode:
tdmOIpCe (2) = TDMOiP (CE) = Circuit Emulation.
tdmOIpCv (3)= TDMOiP (CV) = Compressed Voice.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.58

ip2IfRingBack

Enables or disable Ring Back.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.59

ip2IfReversePolarity

Enables or disable Reverse polarity synthesis.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.60

ip2IfPulseMeter

Enables or disable Pulse metering synthesis.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.61

ip2IfPulseMeterFreq

Frequency of synthesized pulse metering for this bundle.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.62

ip2IfPulseMeterPeriod

Duration of synthesized pulse metering. current values are: 100-250.

SNMPv2-SMIInteger32r/w

Constraints:
range: 1-6

.1.3.6.1.4.1.164.3.1.6.7.1.1.63

ip2IfOnHookDetect

Enables or disable immediate reaction to On-Hook bits from network in Ringing.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.64

ip2IfComfortNoiseGen

Enable or disable Comfort Noise Generation (CNG).
When this parameter is enabled and no voice payload exists on the line for some
time period during the call (moments of silence), the device will generate a soft
back…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.65

ip2IfExitChannel

The channelized bundle that the voice bundle exits through.
In Gmux2000 it is the ifIndex of the Channelized Bundle (sub-channel)
that the Voice Bundle exits through. The ifIndex contains
the Slot+Prt+Channelized Bund…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.66

ip2IfMaxVBDModemCalls

Maximum VBD modem calls for this bundle.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.67

ip2IfMaxRelayModemCalls

Maximum Relay modem calls for this bundle.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.68

ip2IfCustomToneFrequency

This is the frequency of the Custom Tone that is sent between PBXs in order
to check that the line status is OK. When the Custom Tone Detection is enabled
the device will not compress/decompress this tone. The custom to…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.69

ip2IfVadMethod

Voice Activity Detection (VAD) method.
proprietary (2) - non standard VAD based only on power measurement.
It is very sensitive to background noise.
internalITUT (3) - standard ITU-T VAD. It is …

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.70

ip2IfRxGain

Receive gain in dBm.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.71

ip2IfCallerIDType

Caller ID Type used by the DSP for this bundle.
Bellcore type is used by the American method.
V.23 type is used by the European method.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.72

ip2IfPeerAddrType

This MIB object defines the peer Address Type.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.73

ip2IfVbdRate

Voice Band Data (VBD) rate for this bundle.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.74

ip2IfDtmfDetection

Enable/Disable DTMF (Dual Tone Multi Frequency) detectors for this bundle.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.75

ip2IfNlpCutoffLevel

Non Linear Processor (NLP) Cutoff Level for this bundle.
This parameter is used by the echo canceller.
It is the maximum absolute linear PCM amplitude of the near-end signal that will
cause the NLP module to be active a…

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.1.1.76

ip2IfDtdErlRatioCutoffQ3

The DTD ERL cutoff level is used in order to determine whether the near-end is talking
or not. This parameter is used by the echo canceller when echo exists and there is
voice with low volume on the line.
DTD means Doub…

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.1.1.77

ip2IfCASRedundancy

Enable/Disable CAS signaling redundancy.
This parameter is useful when there are problems with the network and applicable
only for CAS signaling: E1-MF (G.732S) or E1-CRC-MF (G.732SCRC ).

enable (3) - mea…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.78

ip2IfBundleSensitivity

Denotes if the bundle is sensitive to delay in the network,
or is sensitive to data errors in the network.
Voice bundles are sensitive to delay;
Non-voice bundles are sensitive to data errors.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.79

ip2IfOAMBundleIdent

Denotes if an OAM bundle is identified according to the Bundle Number (0x3fff),
or according to the value of the first nibble in the VCCV control word sent in the frame.
controlWord - applicable only when ip2IfProtoco…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.80

ip2IfMaxTxQueue

Max Tx Queue buffer size, measured in msec (milliseconds).

Low buffer size may cause the buffer to overflow and discard packets
in case of burst of packets on the network.

High buffer size …

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.1.1.81

ip2IfMaxGprsTxQueue

Max GPRS Tx Queue buffer size, measured in msec (milliseconds).

Low buffer size may cause the buffer to overflow and discard packets
in case of burst of packets on the network.

High …

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.1.1.82

ip2IfV23HD

This parameter shows whether V.23 Half Duplex Modem Protocol is enabled
on the bundle.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.83

ip2IfModemProtocolMode

This octet string contains the mode of each Modem Protocol used on the bundle.
For each protocol one octet will be used.

Octet #1 will be used for V.22 Protocol.
Octet #2, #3, #4... are reserved for futu…

OctetStringr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.84

ip2IfCdisCngDetectionTime

When working with CDIS (Call DIScrimination method) or CNG (Comfort Noise Generation):
The time in msec that the device will detect 1100Hz & 2100Hz signals
on the line before switching to modem or fax.
For Vmux: the val…

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.1.1.85

ip2IfSuperTandemBitMask

This MIB object enables controlling the Time Slot/Channel rate.
Valid values: 1 - FF HEX
Each BIT represents 1/8 of the TS.
Example:
7E (0111 1110) means that 6/8 of the TS (the center ones) are masked and data will
be …

OctetStringr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.86

ip2IfVbdSwitchbackTime

Time in msec required for the DSP to switch back from VBD (Voice Band Data) to Voice.
For Vmux: the values will be in steps of 30 msec.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.1.1.87

ip2IfCallerIdTxGain

The gain value in dBm units used for transmitting the Caller ID signal on the bundle.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.88

ip2IfCallerIdRxGain

The gain value in dBm units of the Caller ID signal received on the bundle.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.1.1.89

ip2IfUdpMuxMethod

This parameter determines according to which field the multiplexing is made:
srcPort (2) - multiplexing according to the UDP Source Port (Dest=0x085e).
This should be the default value, for backwards compatibility.…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	dontMask
3	mask

.1.3.6.1.4.1.164.3.1.6.7.1.1.90

ip2IfCallerIdDetection

Enable/Disable Caller ID Detection for this bundle.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.91

ip2IfWap

Enable/Disable WAP (Wireless Application Protocol) for this bundle.
WAP allows users to access the internet from wireless devices.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.92

ip2IfSignalingOos

Out of Service code sent on signaling TimeSlot.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.7.1.1.93

ip2IfStatTable

table

.1.3.6.1.4.1.164.3.1.6.7.7 · 1 row entry · 36 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ip2IfStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ip2IfStatTable'

Channels (Bundles) Statistics Table.

ip2IfStatEntry row .1.3.6.1.4.1.164.3.1.6.7.7.1

IP Statistics per bundle

Indexes

No indexes recorded

Column Syntax OID

ip2IfStatChIndex

The channel index, which is actualy the bundle ID.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.7.1.1

ip2IfStatSeqErrors

Number of events that the sequence number of an incoming Frame
causes a transition from the 'sync' state to
the 'out of sequence' state.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.7.1.2

ip2IfStatBufUnderflows

Number of events that the buffer underflows. This records the count of the
number of events the Receive (Eth to TDM) buffer underflows. In the
case of a continuous underflow caused by a loss of Frame
flow, a single buff…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.7.1.3

ip2IfStatBufOverflows

Number of events that the buffer overflows. This records the count of the
number of events the Receive (Eth to TDM) buffer overflows.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.7.1.4

ip2IfStatTxOnTimeInterval

Number of frames that were transmitted due to time interval elapse.
The user can choose to Tx the Frame when it reaches the Max size
or when the packetizing time interval elapses.
The packetizing time interval is the in…

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.5

ip2IfStatTxOnMaxSize

Number of frames that were transmitted due to reaching max.
frame size. The user can choose to Tx the Frame when it reaches the
Max size or when the packetizing time interval elapses.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.6

ip2IfStatRxSignaling

Number of signaling frames that were received.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.7

ip2IfStatRxVoice

Number of voice frames that were received.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.8

ip2IfStatRxHdlc

Number of HDLC frames that were received.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.9

ip2IfStatTxSignaling

Number of signaling frames that were transmitted.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.10

ip2IfStatTxVoice

Number of voice frames that were transmitted.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.11

ip2IfStatTxHdlc

Number of HDLC frames that were transmitted.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.12

ip2IfStatRdnFlip

Number of redundancy flips occured.
This parameter counts only flips from this bundle to the other bundle
in the redundancy couple.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.13

ip2IfFarEndTdmStatus

This variable indicates the Status of the Far-End TDM Line.
It contains failure state information.
The variable is a bit map represented as a sum, therefore, it
can represent multiple failures simultaneously.
The …

Integer32

.1.3.6.1.4.1.164.3.1.6.7.7.1.14

ip2IfStatPsnTxFrames

Number of frames that were transmitted to PSN.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.15

ip2IfStatPsnRxFrames

Number of frames that were recieved from PSN.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.16

ip2IfStatMinJittBufLevel

The Minimum jitter buffer level (in msec).

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.17

ip2IfStatMaxJittBufLevel

The Maximum jitter buffer level (in msec).

SNMPv2-SMIUnsigned32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.6.7.7.1.18

ip2IfStatRecommendedJittBufSize

The Recommended jitter buffer Size (in msec).
0= not applicable.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.19

ip2IfStatPsnSeqErrors

Number of times that the sequence number of an incoming Frame
indicates Loss of Frame or Out of order occured in PSN.

SNMPv2-SMICounter32

Enumerated Values:

1	ais
2	rdi
3	aisAndRdi

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.20

ip2IfStatPsnReorderFrames

Number of times that Frames had been reordered in PSN.

SNMPv2-SMICounter32

Enumerated Values:

1	notApplicable
2	slm
3	fail
4	eed
5	pathTrace
6	lom
7	lop
8	slu

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.21

ip2IfStatMinRoundTripDelay

The minimum Round Trip delay (in msec).
0= not applicable.

SNMPv2-SMIUnsigned32

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.22

ip2IfStatMaxRoundTripDelay

The maximum Round Trip delay (in msec).
0= not applicable.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.23

ip2IfStatAvrRoundTripDelay

The avarage Round Trip delay (in msec).
0= not applicable.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.24

ip2IfStatFrameTrackDupDrop

The number of packets dropped due to being duplicated.
(duplicated packet means a packet that has the same sequential
number as a packet being received previously).

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.25

ip2IfStatFrameTrackMissing

The number of packets that are missing.
(Missing packet means an expected packet- according to the current sequential
number - that was not received).

SNMPv2-SMICounter32

Constraints:
range: 0-899

.1.3.6.1.4.1.164.3.1.6.7.7.1.26

ip2IfStatFrameTrackLongSerMiss

The longest series of consecutive missing sequential numbers.
Missing sequential numbers represent missing packets that was
expected to be received successively.

SNMPv2-SMIInteger32

Constraints:
range: 0-96

.1.3.6.1.4.1.164.3.1.6.7.7.1.27

ip2IfStatTxMeasuredSilence

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.7.1.28

ip2IfStatRxMeasuredSilence

This object shows the percentage of Silence that was measured by the device
for the current bundle in the received payload.
Relevant values: 0..100, 255.
Default value is 50.
0 means that there is no silence on the line…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.7.1.29

ip2IfStatHdlcCrcErr

This counter indicates the number of received HDLC frames
with CRC errors.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.30

ip2IfStatHdlcAlignErr

This counter indicates the number of received HDLC frames
with alignment errors.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.31

ip2IfStatHdlcOversize

This counter indicates the number of received HDLC frames
longer than 1470.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.32

ip2IfStatHdlcUndersize

This counter indicates the number of received HDLC frames
shorter than 4.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.33

ip2IfStatHdlcAbort

This counter indicates the number of received HDLC frames
with abort indication.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.34

ip2IfStatRxCorrectFrames

Number of received correct frames.

SNMPv2-SMICounter32

Constraints:
range: 4-4

.1.3.6.1.4.1.164.3.1.6.7.7.1.35

ip2IfStatHdlcErroredFrames

Number of received errored HDLC frames.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.7.1.36

ip2IfPortTable

table

.1.3.6.1.4.1.164.3.1.6.7.9 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ip2IfPortTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ip2IfPortTable'

Port  Table.

ip2IfPortEntry row .1.3.6.1.4.1.164.3.1.6.7.9.1

Application layer configuration per Port

Indexes

IF-MIBifIndex prtPhyIntervalNumber

Column	Syntax	OID
ip2IfPortIndex The Port index, which is actualy the ifIndex.	SNMPv2-SMIInteger32 Constraints: `range: 1-96`	`.1.3.6.1.4.1.164.3.1.6.7.9.1.1`
ip2IfPortUsage This parameter indicates the usage of the port (percents).	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.6.7.9.1.2`
ip2IfPortMask This parameter defines whether Agent will mask port's alarms and statistics or not.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.7.9.1.3`
ip2IfPortTotalThroughput This parameter indicates the total Throughput of the port in bps.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.6.7.9.1.4`

ip2IfCurrentStatTable

table

.1.3.6.1.4.1.164.3.1.6.7.10 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ip2IfCurrentStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ip2IfCurrentStatTable'

Channels (Bundles) Current Statistics Table.

ip2IfCurrentStatEntry row .1.3.6.1.4.1.164.3.1.6.7.10.1

IP Current Statistics per bundle

Indexes

No indexes recorded

Column Syntax OID

ip2IfCurrentStatSeqErrors

Number of seconds that the sequence number of an incoming Frame
causes a transition from the 'sync' state to
the 'out of sequence' state in the current interval.

SNMPv2-SMICounter32

Constraints:
range: 4-4

.1.3.6.1.4.1.164.3.1.6.7.10.1.1

ip2IfCurrentStatBufUnderflows

Number of seconds that the buffer underflows in the current interval.
This records the count of the number of seconds the Receive
(Eth to TDM) buffer underflows in the current interval. In the
case of a continuous und…

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.10.1.2

ip2IfCurrentStatBufOverflows

Number of seconds that the buffer overflows in the current interval.
This records the count of the number of seonds the Receive
(Eth to TDM) buffer overflows in the current interval.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.10.1.3

ip2IfCurrentStatMaxDelayVar

The maximum deviation from the center of the buffer (in msec) for the current interval.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.10.1.4

ip2IfCurrentStatMinJittBufLevel

The Minimum jitter buffer level (in msec) for the current interval.

SNMPv2-SMIUnsigned32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.6.7.10.1.5

ip2IfCurrentStatMaxJittBufLevel

The Maximum jitter buffer level (in msec) for the current interval.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.10.1.6

ip2IfCurrentStatTxErrFrameSec

The number of seconds in which errored frames were transmitted during the current interval.
The error may be one of the following:
CRC error, Alignment error, Oversized frame, Undersized frame, Aborted frame.

SNMPv2-SMICounter32

Enumerated Values:

2	auto
3	manual

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.10.1.7

ip2IfIntervalStatTable

table

.1.3.6.1.4.1.164.3.1.6.7.11 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ip2IfIntervalStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ip2IfIntervalStatTable'

Channels (Bundles) Interval Statistics Table.

ip2IfIntervalStatEntry row .1.3.6.1.4.1.164.3.1.6.7.11.1

IP Interval Statistics per bundle

Indexes

No indexes recorded

Column Syntax OID

ip2IfIntervalStatIndex

The Interval index, which is actualy the Interval number.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	cBit
3	bBit

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.11.1.1

ip2IfIntervalStatSeqErrors

Number of seconds that the sequence number of an incoming Frame
causes a transition from the 'sync' state to
the 'out of sequence' state in the selected interval.

SNMPv2-SMICounter32

Enumerated Values:

1	notApplicable
2	break56Make44
3	break64Make36
4	break80Make20

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.11.1.2

ip2IfIntervalStatBufUnderflows

Number of seconds that the buffer underflows in the selected interval.
This records the count of the number of seconds the Receive
(Eth to TDM) buffer underflows in the selected interval. In the
case of a continuous u…

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.11.1.3

ip2IfIntervalStatBufOverflows

Number of seconds that the buffer overflows in the selected interval.
This records the count of the number of seconds the Receive
(Eth to TDM) buffer overflows in the selected interval.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.11.1.4

ip2IfIntervalStatMaxDelayVar

The maximum size of the buffer (in 10's of usec) in the selected interval.
For some devices (e.g. MP-4100) units are usec.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.7.11.1.5

ip2IfIntervalStatMinJittBufLevel

The Minimum jitter buffer level (in msec) for the selected interval.
For some devices (e.g. MP-4100) units are usec.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.11.1.6

ip2IfIntervalStatMaxJittBufLevel

The Maximum jitter buffer level (in msec) for the selected interval.
For some devices (e.g. MP-4100) units are usec.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.11.1.7

ip2IfIntervalStatTxErrFrameSec

The number of seconds in which errored frames were transmitted during the selected interval.
The error may be one of the following:
CRC error, Alignment error, Oversized frame, Undersized frame, Aborted frame.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.7.11.1.8

prtBdbandIndTable

table

.1.3.6.1.4.1.164.3.1.6.8.1.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtBdbandIndTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtBdbandIndTable'

The Indication Signal table.

prtBdbandIndEntry row .1.3.6.1.4.1.164.3.1.6.8.1.1.1

An entry in the Indication Signal table.

Indexes

No indexes recorded

Column Syntax OID

prtBdbandCnfgIdx

This object indicates the Idx of the Agent Cnfg the following
objects refer.
255=Temporary Cnfg (when relevant, Set is done only to this configuration).
For Agents that support only one configuration, this object will …

Integer32

.1.3.6.1.4.1.164.3.1.6.8.1.1.1.1

prtBdbandIdx

This object indicates a unique port or interface number.
For numbering, see product's spec.
For some products, the numbering can equal ifIndex.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.8.1.1.1.2

prtBdbandIndSig

This object indicates a unique Indication Signal.
ais(1) = AIS = Alarm Indication Signal.
rdi(2) = RDI = Remote Defect Indication.

Enumeration

.1.3.6.1.4.1.164.3.1.6.8.1.1.1.3

prtBdbandIndEvent

This object indicates a unique Event that can cause the Indication Signal.
slm(2) = SLM = Signal Label Mismatch
eed(4) = EED = Excessive Error Defect
pathTrace(5) = the end-to-end source/destination of information is wr…

Enumeration

.1.3.6.1.4.1.164.3.1.6.8.1.1.1.4

prtBdbandIndSigEnable

This object allows user to define if the event specified by prtBdbandIndEvent
will cause creation of the Indication Signal specified by prtBdbandIndSig or not.
disable - will not enable causing the signal
enable - wil…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.8.1.1.1.5

prtBdbandRowStatus

Creation/Deletion of rows in the table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.3.1.6.8.1.1.1.6

prtPhyConfigTable

table

.1.3.6.1.4.1.164.3.1.6.8.1.2 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtPhyConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtPhyConfigTable'

The Phy Config table. Used now for Phy25.6 Mbps.

prtPhyConfigEntry row .1.3.6.1.4.1.164.3.1.6.8.1.2.1

An entry in the Phy Config table.

Indexes

No indexes recorded

Column	Syntax	OID
prtPhyTimeElapsed The number of seconds that have elapsed since the beginning of the current error-measurement period.	Integer32	`.1.3.6.1.4.1.164.3.1.6.8.1.2.1.1`
prtPhyValidIntervals The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 mi…	Integer32	`.1.3.6.1.4.1.164.3.1.6.8.1.2.1.2`

prtPhyCurrentTable

table

.1.3.6.1.4.1.164.3.1.6.8.2.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtPhyCurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtPhyCurrentTable'

The 25.6 Mbps Section/Line Current table.

prtPhyCurrentEntry row .1.3.6.1.4.1.164.3.1.6.8.2.1.1

An entry in the 25.6 Mbps Line Current table.
ifIndex of the line 25.6 Mbps layer of type
25.6 Mbps.

Indexes

r2TsCnfgIdx r2TsProfileIdx r2TsIdx

Column Syntax OID

prtPhyCurrentLOS

The counter associated with the number of Loss Of Sync
seconds, encountered by a 25.6 Mbps interface in
the current 15 minute interval.

SNMPv2-SMIGauge32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.6.8.2.1.1.1

prtPhyCurrentLSV

The counter associated with the number of Line symbol violation
seconds, encountered by a 25.6 Mbps
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.8.2.1.1.2

prtPhyCurrentUAS

The counter associated with the number of UAS
encountered by a 25.6 Mbps
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.8.2.1.1.3

prtPhyCurrentSES

The counter associated with the number of SES
encountered by a 25.6 Mbps
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Enumerated Values:

2	incoming
3	outgoing
4	both

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.8.2.1.1.4

prtPhyCurrentES

The number of Errored Seconds, encountered by a
25.6 Mbps interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Enumerated Values:

2	no
3	yes

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.8.2.1.1.5

prtPhyCurrentStatus

The statuses of the current interval:
0 - O.K.
1 - The link has been switched by a redundancy mechanism.
2 - Module is in/out.
4 - Empty - card is out.

OctetString

.1.3.6.1.4.1.164.3.1.6.8.2.1.1.6

prtPhyCurrentLOF

The number of Loss of Frames, encountered by an
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Enumerated Values:

2	no
3	yes

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.8.2.1.1.7

prtPhyIntervalTable

table

.1.3.6.1.4.1.164.3.1.6.8.2.2 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtPhyIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtPhyIntervalTable'

The Line Interval table.

prtPhyIntervalEntry row .1.3.6.1.4.1.164.3.1.6.8.2.2.1

An entry in the 25.6 Mbps Line Interval table.
ifIndex of the line 25.6 Mbps layer of type 25.6 Mbps.

Indexes

r2StatusSlotIdx r2StatusPortIdx r2StatusTsIdx

Column Syntax OID

prtPhyIntervalNumber

A number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals are valid).

Integer32

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.1.6.8.2.2.1.1

prtPhyIntervalLOS

The counter associated with the number of Loss Of Sync
seconds , encountered by a 25.6 Mbps interface in
one of the previous 96, individual 15 minute intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.8.2.2.1.2

prtPhyIntervalLSV

The counter associated with the number of line symbol violation
seconds , encountered by a 25.6 Mbps interface in
one of the previous 96, individual 15 minute intervals.

SNMPv2-SMIGauge32

Constraints:
range: 1-31

.1.3.6.1.4.1.164.3.1.6.8.2.2.1.3

prtPhyIntervalUAS

The counter associated with the number of UAS
encountered by a 25.6 Mbps interface in one of the previous 96,
individual 15 minute intervals.

SNMPv2-SMIGauge32

Enumerated Values:

1	notApplicable
2	incoming
3	outgoing

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.8.2.2.1.4

prtPhyIntervalSES

The counter associated with the number of SES
encountered by a 25.6 Mbps interface in one of the previous 96,
individual 15 minute intervals.

SNMPv2-SMIGauge32

Enumerated Values:

1	notUsed
2	normal
3	remoteBlocked
4	localBlocked
5	localLoop
6	remoteLoop

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.8.2.2.1.5

prtPhyIntervalES

The number of Errored Seconds, encountered by a
25.6 Mbps interface in one of the previous 96, individual 15
minute intervals.

SNMPv2-SMIGauge32

Enumerated Values:

1	idle
2	seized
3	seizureAcknowledged
4	answered
5	clearForward
6	clearBack
7	blocked
8	forcedDisc
9	doubleSeizure
10	fault
11	discAcknowledged
12	fault1
13	fault6
14	fault3

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.8.2.2.1.6

prtPhyIntervalStatus

The statuses of the current interval:
0 - O.K.
1 - The link has been switched by a redundancy mechanism.
2 - Module is in/out.
4 - Empty - card is out.

OctetString

.1.3.6.1.4.1.164.3.1.6.8.2.2.1.7

prtPhyIntervalLOF

The number of Loss of Frames, encountered by an
interface in one of the previous 96, individual 15
minute intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.8.2.2.1.8

r2CnfgTable

table

.1.3.6.1.4.1.164.3.1.6.9.1.1 · 1 row entry · 25 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk r2CnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::r2CnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

r2CnfgEntry row .1.3.6.1.4.1.164.3.1.6.9.1.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

r2CnfgIdx

This attribute indicates the Idx of the Cnfg being accessed.
255 = TmpCnfg.
1 = Current Cnfg.
Write is allowed only to TmpCnfg.

Integer32

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.1

r2CnfgProfileIdx

Profile Index.
Valid values: 1..5
Only instances of profiles that are defined having agnSigProfType=r2Cas will
exist in this table.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.2

r2Mode

R2 Mode.
auto - in this mode, default value of timers will be used by R2,
according to the selected r2Country.
manual - in this mode, user can change the value of R2 timers within the valid
limits, s…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	echoCancellation
3	frequencyDivision

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.3

r2Country

R2 Country. R2 Timers can have different range of values and
defaults for each country. When r2Mode=auto, the default value is
used by R2 according to this selected country.
1=ITU-T (standard values)
2=Korea
3=Ind…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	t1Hypen413
3	gDotDmt
4	multiMode
5	alcatel1Dot4
6	alcatel
7	adi
8	adsl2
9	adsl2Plus
10	adsl2Auto
11	adsl2PlusAuto

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.4

r2Delay

This object enables user to configure the link as satellite or terrestrial.
The seize acknowledge detect timing is much shorter (msec) for
terrestrial link than for satellite link (1-2 sec).

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.5

r2MeteringInd

Which Bit will be used for Metering Indication.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.6

r2BreakMakeRatio

This object describes the Break-Make Ratio of Pulse Duration, in [msec].
RW only when r2Mode=manual.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.7

r2ReleaseGuardT2

Release Guard timing T2.
Release guard timing before going to idle, in [msec].
RW only when r2Mode=manual.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.8

r2Regret

Regret duration, in [sec].
RW only when r2Mode=manual.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.9

r2SeizeDetect

Seize Detect. Timer of the R2 incoming side.
Minimum duration to detect a valid seizure, in [msec].
RW only when r2Mode=manual.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.10

r2SeizeAckDelay

Timer of the R2 incoming side.
Delay before sending a valid seize ack signal, in [msec].
Applicable only when r2Mode=manual. only when r2Mode=manual.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	standard
3	nonOverlapFlat
4	nonOverlapM1
5	nonOverlapM2

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.11

r2ClearBackDetect

Timer of the R2 incoming side.
Minimum duration to recognize a valid clear-back, in [msec].
RW only when r2Mode=manual.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	off
2	restart

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.12

r2ClearFwdDetect

Timer of the R2 incoming side.
Minimum duration to recognize a valid clear-forward, in [msec].
RW only when r2Mode=manual.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.13

r2FaultDetect

Timer of the R2 incoming side.
Minimum duration to recognize a block signal, in [msec].
RW only when r2Mode=manual.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.14

r2FaultRemoveDetect

Timer of the R2 incoming side.
Minimum duration to recognize a valid block removal signal, in [msec].
RW only when r2Mode=manual.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.15

r2MeterPulseDuration

Timer of the R2 incoming side.
Duration of metering pulse to be sent, in [msec].
RW only when r2Mode=manual.

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	t1Hypen413AnnexA
3	gDotDmtAnnexA
4	multiModeAnnexA
5	alcatel1Dot4AnnexA
6	alcatelAnnexA
7	adiAnnexA
8	t1Hypen413AnnexB
9	gDotDmtAnnexB
10	multiModeAnnexB
11	alcatel1Dot4AnnexB
12	alcatelAnnexB
13	adiAnnexB
14	adsl2AnnexA
15	adsl2PlusAnnexA
16	adsl2AnnexB
17	adsl2PlusAnnexB
18	reachAadslAnnexL

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.16

r2SeizeAckWait

Timer of the R2 outgoing side.
Minimum duration to receive seizure acknowledge signal, in [msec].
RW only when r2Mode=manual.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	idle
2	discovery
3	handshake
4	training
5	data
6	fullInit

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.17

r2SeizeAckDetect

Timer of the R2 outgoing side.
Minimum duration to recognize a valid seizure acknowledge signal, in [msec].
RW only when r2Mode=manual.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.18

r2AnswerDetect

Timer of the R2 outgoing side.
Minimum duration to recognize a valid answer signal, in [msec].
RW only when r2Mode=manual.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	notActive
3	active

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.19

r2BlockRemoveDetect

Timer of the R2 outgoing side.
Minimum duration to recognize a valid block removal signal, in [msec].
RW only when r2Mode=manual.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.20

r2MeterPulseDetect

Timer of the R2 outgoing side.
Minimum duration of incoming meter pulse, in [msec].
RW only when r2Mode=manual.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.21

r2ForcedDisconnect

Timer of the R2 outgoing side.
Minimum duration to recognize disconnect signal, in [msec].
RW only when r2Mode=manual.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.22

r2DisconnectAck

Timer of the R2 outgoing side.
Minimum duration to recognize disconnect acknowledge signal, in [msec].
RW only when r2Mode=manual.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.23

r2ReleaseGuardT1

Timer of the R2 outgoing side.
Minimum duration to release guard, in [msec].
During this time, no new call can be initiated.
RW only when r2Mode=manual.

SNMPv2-SMIInteger32r/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.24

r2CnfgRowStatus

This object enables the user to add/delete entries to/from the table.

SNMPv2-TCRowStatusr/w

Enumerated Values:

1	notApplicable
2	autoNegotiate
3	fixed

Description:

.1.3.6.1.4.1.164.3.1.6.9.1.1.1.25

r2TsTable

table

.1.3.6.1.4.1.164.3.1.6.9.1.2 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk r2TsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::r2TsTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

r2TsEntry row .1.3.6.1.4.1.164.3.1.6.9.1.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

r2TsCnfgIdx

This attribute indicates the Idx of the Cnfg being accessed.
255 = TmpCnfg.
1 = Current Cnfg.
Write is allowed only to TmpCnfg.

Integer32

.1.3.6.1.4.1.164.3.1.6.9.1.2.1.1

r2TsProfileIdx

Profile Index.
Valid values: 1..5
Only instances of profiles that are defined having agnSigProfType=r2Cas will
exist in this table.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.1.2.1.2

r2TsIdx

TS Index.
Valid values: 1..31

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.1.2.1.3

r2TsCallEnable

This object indicates the Enabled Call direction for the specific TS.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.9.1.2.1.4

r2TsMetering

This object indicates if the specific TS should support Metering.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.9.1.2.1.5

r2TsRowStatus

This object enables the user to add/delete entries to/from the table.

SNMPv2-TCRowStatusr/w

Enumerated Values:

2	noSync
3	sync

Description:

.1.3.6.1.4.1.164.3.1.6.9.1.2.1.6

r2TsReversePolarity

This object indicates if the specific TS should support Reverse Polarity.

Enumerationr/w

Enumerated Values:

0	idleMode
1	dataMode
2	bootUpload
3	bootUploadDone
4	startupHandshakeInProgress
5	startupTrainingInProgress
6	framerSyncInProgress
7	localAnalogLoopbackInProgress
8	remoteCoreLoopbackInProgress
9	localDigitalLoopbackInProgress
10	spectrumTestInProgress

.1.3.6.1.4.1.164.3.1.6.9.1.2.1.7

r2StatusTable

table

.1.3.6.1.4.1.164.3.1.6.9.2.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk r2StatusTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::r2StatusTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

r2StatusEntry row .1.3.6.1.4.1.164.3.1.6.9.2.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

r2StatusSlotIdx

Slot Index

Enumeration

.1.3.6.1.4.1.164.3.1.6.9.2.1.1.1

r2StatusPortIdx

This object indicates a unique port number of the ML having
R2 interface.
Valid values: exPrt1 (1)..exPrt4 (4)

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.9.2.1.1.2

r2StatusTsIdx

Time Slot index.

Integer32

.1.3.6.1.4.1.164.3.1.6.9.2.1.1.3

r2StatusSigDirection

R2 Time Slot Signaling Direction.

Enumeration

.1.3.6.1.4.1.164.3.1.6.9.2.1.1.4

r2StatusTsState

R2 TS State

Enumeration

Enumerated Values:

1	default
2	enhanced
3	disabled

.1.3.6.1.4.1.164.3.1.6.9.2.1.1.5

r2StatusProtocolState

R2 Protocol State.

Enumeration

.1.3.6.1.4.1.164.3.1.6.9.2.1.1.6

adslConfTable

table

.1.3.6.1.4.1.164.3.1.6.10.1 · 1 row entry · 14 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk adslConfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::adslConfTable'

A list of ADSL Configuration entries

adslConfEntry row .1.3.6.1.4.1.164.3.1.6.10.1.1

An entry in adslConfTable

Indexes

No indexes recorded

Column Syntax OID

adslConfCnfgIdx

This object indicates the Idx of the Config being accessed.
Idx of 255 relates to the Temporary (Scratch) Config.
For products that support several configurations,
Set can be performed only to the Temporary Config (=25…

Integer32

Enumerated Values:

1	notApplicable
2	asymmetricR1
3	asymmetricR2

.1.3.6.1.4.1.164.3.1.6.10.1.1.1

adslConfFramingType

ADSL Frame type

Enumerationr/w

Enumerated Values:

1	notApplicable
2	twoWires
3	fourWires
4	autoDetection

.1.3.6.1.4.1.164.3.1.6.10.1.1.2

adslConfPilotToneRequest

This parameter controls Pilot Tone Request (PTR).

Enumerationr/w

Enumerated Values:

1	automatic
2	g994dot1rev2001

.1.3.6.1.4.1.164.3.1.6.10.1.1.3

adslConfTrellisCoding

This parameter enables/disables Trellis error detection code.
using error detection code may introduce delays.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.10.1.1.4

adslConfTransmissionMode

This parameter controls transmision mode:
Echo Cancellation is required when both ATU-C an ATU-R use
the same frequency.
Frequency Division (different frequency ranges for ATU-C
and ATU-R) may limit data rate.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.10.1.1.5

adslConfStandardCompliance

This parameter indicates standard compliance
G.Lite enables extended ADSL range, ease of installation,
but requires lower rate.

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.6.10.1.1.6

adslConfMaxBitPerBin

This parameter indicates maximum number of bits per ADSL Bin.
Each Bin has bandwidth of 4khz.
Range of values for this parameter is 0..15

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	nearEnd
3	farEnd

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.10.1.1.7

adslConfTxStartFreqBin

This parameter controls Transmit Start Bin number.
For ADSL Annex A - range of values is 6 to 31.
For ADSL Annex B - range of values is 33 to 63.
Frequency (in khz unit) is calculated by multiplying this
parameter v…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	r192
3	r256
4	r320
5	r384
6	r448
7	r512
8	r576
9	r640
10	r704
11	r768
12	r832
13	r896
14	r960
15	r1024
16	r1088
17	r1152
18	r1216
19	r1280
20	r1344
21	r1408
22	r1472
23	r1536
24	r1600
25	r1664
26	r1728
27	r1792
28	r1856
29	r1920
30	r1984
31	r2048

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.10.1.1.8

adslConfTxEndFreqBin

This parameter controls Transmit End Bin number.
For ADSL Annex A - range of values is 6 to 31.
For ADSL Annex B - range of values is 33 to 63.
requency (in khz unit) is calculated by multiplying this
value by bi…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	enhanced
3	disabled

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.10.1.1.9

adslConfRxStartFreqBin

This parameter controls Receive Start Bin number.
Range of values for this parameter depends on ADSL Annex supported,
and transmisson mode (adslTransmissionMode) selected:
ADSL Annex A and Echo Cancellation (EC) : …

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	annexA
3	annexB
4	annexG
5	annexF

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.10.1.1.10

adslConfRxEndFreqBin

This parameter controls Receive End Bin number.
Range of values for this parameter depends on ADSL Annex supported,
and transmisson mode (adslTransmissionMode) selected:
ADSL Annex A and Echo Cancellation (EC) : 6…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.10.1.1.11

adslConfTxPowerAttenuation

This parameter controls Transmit Gain in dB units
Range is 0 to 12dB. Resolution is 1 dB

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.10.1.1.12

adslConfPSDMask

This parameter controls Power Spectral Density Mask.
This object is applicable only for ADSL2.
(adslConfStandardCompliance is one of the following:
adsl2, adsl2Plus, adsl2Auto, adsl2PlusAuto

Enumerationr/w

Enumerated Values:

1	notApplicable
2	looped
3	transparent

.1.3.6.1.4.1.164.3.1.6.10.1.1.13

adslConfCommand

This parameter enables the user to perform commands on ADSL.
off(1) - default state.
After any operation ends, value should be automatically
set to off(1).
restart(2) - restarts line synchronization process.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	stuC
3	stuR

.1.3.6.1.4.1.164.3.1.6.10.1.1.14

adslStatusTable

table

.1.3.6.1.4.1.164.3.1.6.10.2 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk adslStatusTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::adslStatusTable'

A list of Adsl Status entries

adslStatusEntry row .1.3.6.1.4.1.164.3.1.6.10.2.1

An entry in adslStatusTable

Indexes

No indexes recorded

Column Syntax OID

adslStatusBitRxRate

This parameter indicates actual Receive (Downstream)
rate on this channel.

bpsSNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.10.2.1.1

adslStatusSelectedStandard

This parameter indicates actual Standard
(transsmission mode) chosen after syncronization.

Enumeration

Enumerated Values:

2	other
3	mpComponent
4	asmi52SingleIf
5	asmi52E1AndData
6	asmi52E1AndEth
7	asmi52EthAndData
8	fcdip
9	dxc

.1.3.6.1.4.1.164.3.1.6.10.2.1.2

adslStatusOperationalState

This parameter indicates syncronization status.

Enumeration

.1.3.6.1.4.1.164.3.1.6.10.2.1.3

adslStatusBitErrorRate

This parameter indicates the ratio between the number
of erroneous bits to the total bits number.
The value is normalized to 10e-8.
e.g. BER = 10 means BER = 10*10e-8 = 10e-7

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.10.2.1.4

adslStatusSNRCompensationMode

This parameter indicates whether special SNR compensation mode
has been activated or not.

Enumeration

.1.3.6.1.4.1.164.3.1.6.10.2.1.5

adslStatusSNRCompensation

This parameter indicates the target-SNR Firmware currently used.

dBSNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.10.2.1.6

adslStatusSNRCorrection

This parameter indicates whether the ADSL chip is operating
according to standard ADSL coding gain (auto) or
some other automatic SW configuration (respective to line attenuation).
Units of this parameter are tenths of…

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.10.2.1.7

sdslConfTable

table

.1.3.6.1.4.1.164.3.1.6.11.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sdslConfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sdslConfTable'

A list of SDSL Configuration entries

sdslConfEntry row .1.3.6.1.4.1.164.3.1.6.11.1.1

An entry in sdslConfTable

Indexes

No indexes recorded

Column	Syntax	OID
sdslConfCnfgIdx This object indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For products that support several configurations, Set can be performed only to the Temporary Config (=255…	Integer32	`.1.3.6.1.4.1.164.3.1.6.11.1.1.1`
sdslConfRateAquisition SDSL Rate Aquisition mode Default value = fixed.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.11.1.1.2`
sdslConfBaudRate SDSL baud rate. Not applicable if rate aquisition is AutoNegotiation. Default value = r144kbps	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.11.1.1.3`
sdslConfMode SDSL mode - COE (HTU-C) or CPE (HTU-R) Default value = COE	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.11.1.1.4`

shdslEndpointCurrTable

table

.1.3.6.1.4.1.164.3.1.6.12.1 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk shdslEndpointCurrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::shdslEndpointCurrTable'

This table is an extension of hdsl2ShdslEndpointCurrTable of rfc3276
It contains current status and performance information
for segment endpoints in HDSL2/SHDSL Lines.  As with other 
tables in this MIB indexed by ifIndex, entries in this table 
MUST be maintained in a persistent manner.

shdslEndpointCurrEntry row .1.3.6.1.4.1.164.3.1.6.12.1.1

An entry in the shdslEndpointCurrTable. Each entry
contains status and performance information relating to a
single segment endpoint. It is indexed by the ifIndex of the
HDSL2/SHDSL line, the UnitId of the associate…

Indexes

voiceIfCnfgIdx voiceIfPortIdx

Column Syntax OID

hdsl2ShdslEndpointCurrRcvGain

The current receive gain in hundredth of dB.

dBSNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.12.1.1.1

hdsl2ShdslEndpointCurrTransPower

The current transmit power in tenth of dBm.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.12.1.1.2

hdsl2ShdslEndpointCurrPowerBO

The current transceiver actual power backoff from 0dB to 31dB.

dBSNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.12.1.1.3

hdsl2ShdslEndpointCurrLineStatus

The current line synchronization status.

Enumeration

.1.3.6.1.4.1.164.3.1.6.12.1.1.4

hdsl2ShdslEndpointCurrOpState

The current operational state.

Bits

.1.3.6.1.4.1.164.3.1.6.12.1.1.5

hdsl2ShdslEndpointAccumulatedTimeElapsed

The time (in hundredths of a second) since the
accumulated counters were last re-initialized:
Accumulated counters are hdsl2ShdslEndpointES,
hdsl2ShdslEndpointSES, hdsl2ShdslEndpointCRCanomalies
hdsl2S…

RFC1155-SMITimeTicks

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.12.1.1.6

hdsl2ShdslEndpointCurrPsd

This object indicates use of symmetric/asymmetric PSD (Power
Spectral Density) Mask for the associated SHDSL Line.

Enumeration

.1.3.6.1.4.1.164.3.1.6.12.1.1.7

hdsl2ShdslEndpointValidIntervals

The number of previous 15 minutes intervals
for which valid data was collected.

SNMPv2-SMIUnsigned32

Enumerated Values:

1	notApplicable
2	onHook
3	offHook

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.12.1.1.8

hdsl2ShdslEndpointValidDaysIntervals

The number of previous Days intervals
for which valid data was collected.

SNMPv2-SMIUnsigned32

Enumerated Values:

1	noCall
2	oos
3	dialing
4	waitForAlert
5	waitForConnect
6	ringing
7	active
8	waitForReject
9	waitForInfo

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.12.1.1.9

shdslEndpointMaintTable

table

.1.3.6.1.4.1.164.3.1.6.12.2 · 1 row entry · 1 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk shdslEndpointMaintTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::shdslEndpointMaintTable'

This table supports maintenance operations (eg. loopbacks)
to be performed on HDSL2/SHDSL segment endpoints.  This table
contains live data from equipment.  As such, it is NOT 
persistent.

shdslEndpointMaintEntry row .1.3.6.1.4.1.164.3.1.6.12.2.1

An entry in the hdsl2ShdslEndpointMaintTable. Each entry
corresponds to a single segment endpoint, and is indexed by the
ifIndex of the HDSL2/SHDSL line, the UnitId of the associated
unit and the side of the unit.

Indexes

prtGsmConfigIdx1 prtGsmConfigIdx2

Column	Syntax	OID
shdslMaintPowerBackOff This object configures the receiver at the associated segment endpoint to operate in default or enhanced power backoff mode. powerbackoff may also be disabled	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.12.2.1.1`

shdslSpanConfProfileTable

table

.1.3.6.1.4.1.164.3.1.6.12.3 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk shdslSpanConfProfileTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::shdslSpanConfProfileTable'

This table supports definitions of span configuration
profiles for SHDSL lines.  HDSL2 does not support these 
configuration options.  This table MUST be maintained
in a persistent manner.

shdslSpanConfProfileEntry row .1.3.6.1.4.1.164.3.1.6.12.3.1

Each entry corresponds to a single span configuration
profile. Each profile contains a set of span configuration
parameters. The configuration parameters in a profile are
applied to those lines referencing that profil…

Indexes

No indexes recorded

Column Syntax OID

hdsl2ShdslSpanConfEocCompatible

This object indicate if device supports only
standard EOC messages or also proprietary messages.

Enumeration

Enumerated Values:

1	upStream
2	downStream

.1.3.6.1.4.1.164.3.1.6.12.3.1.1

hdsl2ShdslSpanConfAsymmetricPSDRate

This object indicates line rate when
rfc3276.hdsl2ShdslSpanConfPSD value is asymmetric(2).
Seleceted rate depends on transmission mode -
specified in Annex A or B of G.991.2.
For Annex A;
R1 selects the 776 or …

Enumerationr/w

Enumerated Values:

1	dynamic
2	r8Kbps
3	r16Kbps

.1.3.6.1.4.1.164.3.1.6.12.3.1.2

hdsl2ShdslSpanConfWireInterfaceUsed

This object enable user to configure SHDSL port with 4 wires
to use 2 or 4 wires, or to auto detect far end number of wires

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.1.6.12.3.1.3

hdsl2ShdslSpanConfHandshake

This object indicates the Handshake Procedure.

Enumerationr/w

Enumerated Values:

1	idlePcm
2	idleSpeech
3	asymIdleSpeech

.1.3.6.1.4.1.164.3.1.6.12.3.1.4

hdsl2ShdslIfConfTable

table

.1.3.6.1.4.1.164.3.1.6.12.4.1 · 1 row entry · 15 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk hdsl2ShdslIfConfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::hdsl2ShdslIfConfTable'

This table enables configuration of HDSL2/SHDSL interfaces
per configuration index.
Write operation for products supporting Active+Temp configurations,
is possible only on the Temp configuration(255).

hdsl2ShdslIfConfEntry row .1.3.6.1.4.1.164.3.1.6.12.4.1.1

An entry in the hdsl2ShdslIfConfTable.

Indexes

No indexes recorded

Column Syntax OID

hdsl2ShdslIfConfIdx

This object indicates the Idx of the Config being accessed.
Idx of 255 relates to the Temporary (Scratch) Config.
Write operation for products supporting Active+Temp configurations,
is allowed to Temporary configuratio…

Integer32

Enumerated Values:

2	disable
3	enable

.1.3.6.1.4.1.164.3.1.6.12.4.1.1.1

hdsl2ShdslSideIdx

This object indicates the Side of the managed object: Near-End
or Far-End.

Enumeration

Enumerated Values:

2	disable
3	enable

.1.3.6.1.4.1.164.3.1.6.12.4.1.1.2

hdsl2ShdslMaxBw

Maximum BW (Bandwidth) of the Shdsl Line, in Kbps units.
Respective Max No. of TSs = Max. Rate/64
This object can be Set only for a Central (xtuC) unit.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.12.4.1.1.3

hdsl2ShdslPwrBackoff

This object configures the receiver at the associated
segment endpoint to enable/disable power backoff mode.
This object is similar to hdsl2ShdslMaintPowerBackOff, but per
configuration. Therefore, the order of the enum…

Enumerationr/w

Enumerated Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy
255	notApplicable

.1.3.6.1.4.1.164.3.1.6.12.4.1.1.4

hdsl2ShdslTxMode

This object configures the Transmission Mode for the SHDSL Line.
Normally, This object can be Set only for a Central (xtuC) unit.

Enumerationr/w

Enumerated Values:

0	optimization
1	compression

.1.3.6.1.4.1.164.3.1.6.12.4.1.1.5

hdsl2ShdslAttenuationThreshold

This object configures the Attentuation alarm threshold.
0=Off
Valid values: 0..127 .

dBSNMPv2-SMIInteger32r/w

Enumerated Values:

0	optimization
1	compression

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.12.4.1.1.6

hdsl2ShdslSnrMarginThreshold

This object configures the SNR margin alarm threshold.
0=Off
Valid values: 0..15 .

dBSNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.12.4.1.1.7

hdsl2ShdslTs0OverDsl

This object configures the way TS0 will be treated over the SHDSL Line.
looped - looped inside
transparent - sent transparently over the DSL Line.
This object can be Set only for a Central (xtuC) unit.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.12.4.1.1.8

hdsl2ShdslMode

This object is relevant only for the Near-End device.
stuC - Central
stuR - Remote .

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.12.4.1.1.9

hdsl2ShdslTsCompactionMode

This object configures how TSs will be compacted over the SHDSL Line.
In both mapping cases (2),(3), only the TSs connected on the E1 line will be
transferred over the SHDSL Line
noCompaction - the whole E1 BW is reser…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.12.4.1.1.10

hdsl2ShdslEocEnable

This object configures whether EOC protocol is supported by the Far-End
device working with this port.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.12.4.1.1.11

hdsl2ShdslFar1stIfNumOfTSs

This object configures the number of TSs of the SHDSL line
that belong to the 1st Interface of the Far-End device, where
1st means that these TSs are first on the SHDSL line.

It is applicable only for N…

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.12.4.1.1.12

hdsl2ShdslFarEndDevice

This object indicates the Far-End device.
It is used for 2 purposes:
- in order to know if EOC is used (EOC is used only when the device
is any of the ASMi52 options: (4)..(7))
- in order to know how to work vs Far-En…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.12.4.1.1.13

hdsl2ShdslPwrBackoffDb

This object configures the Power Backoff (in dB) of the
receiver, at the associated segment endpoint.
0=Off
Valid values: 0..31 .

dBSNMPv2-SMIInteger32r/w

Enumerated Values:

1	signaling
2	voice
3	data

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.12.4.1.1.14

hdsl2ShdslFarEndMuxTsa

This object represents Assignment of E1 TSs to Far-End MUX Interfaces.
It is relevant only when hdsl2ShdslSideIdx=nearEnd(2), when for the
Near-End device, hdsl2ShdslMode=stuC(2)AND hdsl2ShdslFarEndDevice=(5),(6)or(7).…

OctetStringr/w

.1.3.6.1.4.1.164.3.1.6.12.4.1.1.15

voiceIfCadenceCnfgTable

table

.1.3.6.1.4.1.164.3.1.6.13.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk voiceIfCadenceCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::voiceIfCadenceCnfgTable'

Voice port ringing cadence configuration table.
Each ringing cycle, indexed by voiceIfCadenceIdx,
consists of a number of ring ON-Period/ring OFF-Period 
pairs. Pairs are indexed sequentially, according to 
voiceIfCadencePeriodIdx: 1,2,...number of pairs

voiceIfCadenceCnfgEntry row .1.3.6.1.4.1.164.3.1.6.13.1.1

Ringing cadence configuration per voice port.

Indexes

No indexes recorded

Column Syntax OID

voiceIfCadenceCnfgIdx

This object indicates the Idx of the
Agent Cnfg the following objects refer to.
255=Temporary Cnfg (when relevant,
Set is done only to this configuration).
For Agents that support only one configuration,
this objec…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.13.1.1.1

voiceIfCadencePortIdx

Voice Port Index. May equal to the value of ifIndex.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.13.1.1.2

voiceIfCadenceIdx

Cadence (ringing type) index.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.13.1.1.3

voiceIfCadencePeriodIdx

Periods index (pair number) in a ringing cycle Cadence.
This index must be sequential, start from 1. Its maximum
value is the number of pairs of certain ringing type.

For Vmux-110, one or two period pair…

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	f64Kbps
3	f56Kbps
4	userDefined

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.13.1.1.4

voiceIfCadenceRowStatus

This attribute allows to create/delete
ringing cadence entry in this table.
For Vmux-110, only a single cadance can be defined.
Delete action of a period entry can be performed only
if it is the last existing period of…

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.3.1.6.13.1.1.5

voiceIfCadenceRingOnPeriod

Duration (in tenth of seconds) of Ringing (ON)
period.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.13.1.1.6

voiceIfCadenceRingOffPeriod

Duration (in tenth of seconds) of Silence (OFF)
period.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.13.1.1.7

voiceIfCnfgTable

table

.1.3.6.1.4.1.164.3.1.6.13.2 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk voiceIfCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::voiceIfCnfgTable'

Voice port configuration table.

voiceIfCnfgEntry row .1.3.6.1.4.1.164.3.1.6.13.2.1

Configuration per voice port.

Indexes

pdhLogPrtCnfgIdx pdhLogPrtIndex

Column Syntax OID

voiceIfCnfgIdx

SNMPv2-SMIInteger32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.6.13.2.1.1

voiceIfPortIdx

Index of voice port .

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.13.2.1.2

voiceIfRingingTimeout

Ringing timeout in seconds.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.13.2.1.3

voiceIfFlashTimeout

A time period in milliseconds. Flash (Register Recall)
is detected if On-Hook time is shorter than this timeout.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.13.2.1.4

voiceIfRxGain

Receive gain in dB.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.13.2.1.5

voiceIfTxGain

Transmission gain in dB.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.6.13.2.1.6

voiceIfSignalingABCD

Octet String.
Nibble No. 1 represents ON Hook (same for Rx and Tx).
Nibble No. 2 represents OFF Hook (same for Rx and Tx).
Nibble No. 3 represents Reverse Polarity.
Nibble No. 4 represents Ring pattern 1.
Nibble No.…

OctetStringr/w

Enumerated Values:

1	notApplicable
2	notDelineated
3	delineated

.1.3.6.1.4.1.164.3.1.6.13.2.1.7

voiceIfState

Attribute indicating voice port state.

Enumeration

.1.3.6.1.4.1.164.3.1.6.13.2.1.8

voiceIfCallState

Attribute indicating the status of the call on this port.
In Vmux devices this attribute is used for FXS ports.

Enumeration

.1.3.6.1.4.1.164.3.1.6.13.2.1.9

prtGsmConfigTable

table

.1.3.6.1.4.1.164.3.1.6.14.1.1 · 1 row entry · 18 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtGsmConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtGsmConfigTable'

GSM Interface Configuration Table.

prtGsmConfigEntry row .1.3.6.1.4.1.164.3.1.6.14.1.1.1

An entry in the GSM Interface Configuration Table.

Indexes

No indexes recorded

Column Syntax OID

prtGsmConfigIdx1

The first index of the table.

This object might represent the Configuration Index (1..100) being accessed,
where Index=255 relates to the TmpCnfg.
For devices with multiple configurations, Set is permitte…

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.14.1.1.1.1

prtGsmConfigIdx2

The second index of the table.

This object might represent the port index
and for some devices might be the ifIndex.

For System level or when NA, value = 1.

SNMPv2-SMIUnsigned32

Enumerated Values:

1	notApplicable
2	fail
3	ok

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.14.1.1.1.2

prtGsmConfigIfType

The GSM Interface Type.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	fail
3	ok

.1.3.6.1.4.1.164.3.1.6.14.1.1.1.3

prtGsmConfigUplinkTxDirection

The Tx Direction toward the network.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.14.1.1.1.4

prtGsmConfigSubChRate

The Sub Channel Rate.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.14.1.1.1.5

prtGsmConfigClockTracking

The Clock Tracking.
This object is relevant only when Egress Uplink is LAN and
the device (e.g. Vmux) on the BSC side is Rx Clock and
the device (e.g. Vmux) on the BTS side is Internal Clock.

On this conf…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.14.1.1.1.6

prtGsmConfigTrauIdleFrame

The TRAU frame to be used between calls.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.14.1.1.1.7

prtGsmConfigDownlinkTrauSilenceFrame

The TRAU frame to be used in the downlink direction
for silence/missing data.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.14.1.1.1.8

prtGsmConfigGprsFrame

The GPRS Frame Type.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.14.1.1.1.9

prtGsmConfigUnkTrauFrameSuppression

This object enables/disables suppression of unknown TRAU frames.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.14.1.1.1.10

prtGsmConfigUnkTrauFrameOptimization

This object enables/disables optimization of unknown TRAU frames.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.14.1.1.1.11

prtGsmConfigSilenceSuppressionRatio

The Silence Suppression Ratio, measured in percentages (1%).
0 = No Suppression.

In case comfort noise is rapidly changed,
it may cause the silence to be heard like a dead line
instead of hearing the comf…

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.14.1.1.1.12

prtGsmConfigStatus

This object enables the user to create/delete entries in this table.
Its usage for values (1)..(6) should be identical to RowStatus SYNTAX.

notApplicable(255) - should be used when the table is static
…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.14.1.1.1.13

prtGsmConfigUpstreamOptimization

This object represents the Optimization Mode
at the Upstream direction (BTS -> BSC).

Bitsr/w

Enumerated Values:

2	direct
3	routed
255	notApplicable

.1.3.6.1.4.1.164.3.1.6.14.1.1.1.14

prtGsmConfigDownstreamOptimization

This object represents the Optimization Mode
at the Downstream direction (BSC -> BTS).

Bitsr/w

.1.3.6.1.4.1.164.3.1.6.14.1.1.1.15

prtGsmConfigByteReversal

This object defines whether BTS/BSC reverses the bytes or not.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.6.14.1.1.1.16

prtGsmConfigTxJitter

The Transmit Jitter size (in msec), towards the BTS/BSC

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.14.1.1.1.17

prtGsmConfigSpdThreshold

The SPD (Smart Packet Drop) Threshold.

SPD mechanism decides which frames to drop
according to the voice energy of the frame.

A frame should be dropped in case its voice energy
is lower tha…

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

2	acceptAll
3	registeredOnly
4	predefinedOnly

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.14.1.1.1.18

prtGsmTrafficTable

table

.1.3.6.1.4.1.164.3.1.6.14.1.2 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtGsmTrafficTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtGsmTrafficTable'

GSM Interface Traffic Table.

prtGsmTrafficEntry row .1.3.6.1.4.1.164.3.1.6.14.1.2.1

An entry in the GSM Interface Traffic Table.

Indexes

No indexes recorded

Column Syntax OID

prtGsmTrafficIdx1

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.14.1.2.1.1

prtGsmTrafficIdx2

The second index of the table.

This object might represent the port index
and for some devices might be the ifIndex.

For System level or when NA, value = 1.

SNMPv2-SMIUnsigned32

Enumerated Values:

2	acceptAll
3	predefinedOnly
4	registrationReject

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.14.1.2.1.2

prtGsmTrafficType

The GSM Interface Traffic Type.

Enumeration

.1.3.6.1.4.1.164.3.1.6.14.1.2.1.3

prtGsmTrafficVpi

The VPI (of VPI/VCI pair) that should be used in connection
with this traffic type.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.14.1.2.1.4

prtGsmTrafficVci

The VCI (of VPI/VCI pair) that should be used in connection
with this traffic type.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.14.1.2.1.5

prtGsmTrafficMultiplexFrameSize

The Multiplexed Frame Size (in bytes) of this traffic type.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.14.1.2.1.6

prtGsmTrafficTxInterval

The Tx Interval (in msec) of this traffic type.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.14.1.2.1.7

ds0BundleTable

table

.1.3.6.1.4.1.164.3.1.6.15.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ds0BundleTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ds0BundleTable'

This table contains additional objects for the standard dsx0BundleTable.

ds0BundleEntry row .1.3.6.1.4.1.164.3.1.6.15.1.1

An entry augmenting the standard dsx0BundleEntry.

Indexes

No indexes recorded

Column	Syntax	OID
ds0BundleTsBitFilter Filter for controlling the bandwidth of the bundle. The TS Bit Filter contains 8 bits (Hex): 00..FF. When a bit is 0: it means that no data will be Tx/Rx on this bit. For example: FF means 64K. In this case all 8 bits w…	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.6.15.1.1.1`
ds0BundleUserDefTsBitFilter User Defined Filter for controlling the bandwidth of the bundle. This MIB object is relevant only when ds0BundleTsBitFilter = userDefined (4) This object is useful for users who want to define a special Filter that cann…	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.6.15.1.1.2`
ds0BundleTdmPortNum This parameter indicates the TDM port number that the bundle is associated to.	SNMPv2-SMIUnsigned32r/w Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.15.1.1.3`
ds0BundleTimeslotMask This parameter indicates the timeslots allocated for the bundle: Each bit represents a timeslot. Setting a bit to '1' denotes that the corresponding timeslot is allocated for that bundle. Bit 0 is not in use, since time…	SNMPv2-SMIUnsigned32r/w Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.15.1.1.4`

pdhLogPrtConfigTable

table

.1.3.6.1.4.1.164.3.1.6.16.1.1 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pdhLogPrtConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pdhLogPrtConfigTable'

Configuration for PDH (Plesiochronous Digital Hierarchy) Logical 
ports/interfaces.
For example: GFP (Generic Framing Procedure) logical interface
or VCG (Virtual Concatenation Group) logical interface.

pdhLogPrtConfigEntry row .1.3.6.1.4.1.164.3.1.6.16.1.1.1

Entry in Configuration Table for PDH Logical Ports.

Indexes

No indexes recorded

Column Syntax OID

pdhLogPrtCnfgIdx

This object indicates the Index of the Configuration being accessed.
Index of 255 relates to the Temporary/Edit (Scratch) Configuration.
For products that support several configurations, Set can be performed
only to the…

Integer32

Enumerated Values:

2	uponDynamicReg
3	always

.1.3.6.1.4.1.164.3.1.6.16.1.1.1.1

pdhLogPrtIndex

This object indicates the number or ifIndex of the selected logical port.

SNMPv2-SMIUnsigned32

Enumerated Values:

2	online
3	offline

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.16.1.1.1.2

pdhLogPrtMaxDiffDelay

Maximum Differential Delay.
Largest allowed difference in msec. between delays in two links (E1/T1)
that are members of the selected VCG.

This object is relevant for VCG (Virtual Concatenation Group) only.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.6.16.1.1.1.3

pdhLogPrtStatusTable

table

.1.3.6.1.4.1.164.3.1.6.16.2.1 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pdhLogPrtStatusTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pdhLogPrtStatusTable'

Status of PDH logical port

pdhLogPrtStatusEntry row .1.3.6.1.4.1.164.3.1.6.16.2.1.1

Entry in the PDH Logical Port Status Table

Indexes

No indexes recorded

Column	Syntax	OID
pdhLogPrtStatusIndex This object indicates the number or ifIndex of the selected logical port.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.16.2.1.1.1`
pdhLogPrtFrameDelineation This object is relevant for GFP (Generic Framing Procedure) only. It indicates the GFP Frame delineation status. Frame delineation means that the device has found the start of a frame - the protocol is synchronized	Enumeration	`.1.3.6.1.4.1.164.3.1.6.16.2.1.1.2`
pdhLogPrtDiffDelay Differential Delay. This object indicates the largest detected difference in msec. between delays in two links (E1/T1) that are members of the selected VCG.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.16.2.1.1.3`

vcgLcasMembersStatusTable

table

.1.3.6.1.4.1.164.3.1.6.16.2.2 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk vcgLcasMembersStatusTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::vcgLcasMembersStatusTable'

Status for LCAS (Link Capacity Adjustment Scheme) members (links) of VCG 
logical port.

vcgLcasMembersStatusEntry row .1.3.6.1.4.1.164.3.1.6.16.2.2.1

Entry in LCAS (Link Capacity Adjustment Scheme) links status table for
VCG (Virtual Concatenation Group) logical port.

Indexes

No indexes recorded

Column	Syntax	OID
vcgLcasMembersVcgIndex This object indicates the number or ifIndex of the selected VCG (Virtual Concatenation Group) logical port.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.16.2.2.1.1`
vcgLcasMembersLinkIndex This object indicates the number or ifIndex of the PDH link that is a member of the VCG.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.16.2.2.1.2`
vcgLcasMembersSourceStatus This object summarizes the LCAS status of the source (Tx) side of the link.	Enumeration	`.1.3.6.1.4.1.164.3.1.6.16.2.2.1.3`
vcgLcasMembersSinkStatus This object summarizes the LCAS status of the sink (Rx) side of the link.	Enumeration	`.1.3.6.1.4.1.164.3.1.6.16.2.2.1.4`

pdhLogPrtStatisTable

table

.1.3.6.1.4.1.164.3.1.6.16.3.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pdhLogPrtStatisTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pdhLogPrtStatisTable'

Statistics for PDH (Plesiochronous Digital Hierarchy) Logical Port,
currently used for GFP (Generic Framing Procedure) interface.

pdhLogPrtStatisEntry row .1.3.6.1.4.1.164.3.1.6.16.3.1.1

Entry in Statistics Table for PDH (Plesiochronous Digital Hierarchy) Logical Port.

Indexes

No indexes recorded

Column	Syntax	OID
pdhLogPrtStatisIndex This object indicates the number or ifIndex of the selected Interface.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.16.3.1.1.1`
pdhLogPrtStatisRxCorrFrames This object indicates the total number of Correct Frames received.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.16.3.1.1.2`
pdhLogPrtStatisRxCorrOctets This object indicates the total number of Correct Octets received.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.16.3.1.1.3`
pdhLogPrtStatisRxCHecErrors This object indicates the total number of Frames received with errors in the Core header (i.e. cHEC field. cHEC means Core Header Error Correction).	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.16.3.1.1.4`
pdhLogPrtStatisRxTHecErrors This object indicates the total number of Frames received with errors in the Type header (i.e. tHEC field. tHEC means Type Header Error Correction).	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.16.3.1.1.5`
pdhLogPrtStatisRxFcsErrors This object indicates the total number of Frames received with Frame Check Sequence errors.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.1.6.16.3.1.1.6`

gkGenTable

table

.1.3.6.1.4.1.164.3.1.7.2 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk gkGenTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::gkGenTable'

General parameters for the VOIP GateKeeper.

gkGenEntry row .1.3.6.1.4.1.164.3.1.7.2.1

An entry in table gkGenTable.

Indexes

IF-MIBifIndex

Column Syntax OID

gkGenCallMode

This parameters shows whether the calls will go through the GK (routed) or
whether the calls will be direct from Endpoint to Endpoint without involving
the GK (direct).

Enumerationr/w

.1.3.6.1.4.1.164.3.1.7.2.1.1

gkGenMaxConnections

MAX no. of connections enabled by the GK to take place simultaneously.
If the MAX no. of calls is exceeded, a busy signal will be returned.

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.7.2.1.2

gkGenDefaultDistance

The Distance allowed for endpoints that are registered dynamically.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.7.2.1.3

gkGenOutOfZoneDist

The Distance allowed for an out of zone endpoint that is making a call
through the gatekeeper.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.7.2.1.4

gkGenCallAcceptPolicy

Defines the policy concerning the incoming phone calls.
The importance of this parameter is for bidding and security matters.
Accept All - all the incoming calls are accepted.
Registered Only - the calls are accepted fr…

Enumerationr/w

Enumerated Values:

2	disable
3	multiplexType1
4	multiplexType2

.1.3.6.1.4.1.164.3.1.7.2.1.5

gkGenIrqInterval

In order for the Gatekeeper to determine if an endpoint is turned off,
or has otherwise entered a failure mode, the Gatekeeper may use the Information
Request (IRQ) to poll the endpoints at the certain interval (in seco…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.7.2.1.6

gkGenQ931Port

Q.931 Port no.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.7.2.1.7

gkGenRasPort

RAS Port no.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.7.2.1.8

gkGenRegPolicy

Policy of dynamic registrations in the Gatekeeper.
The GK will act according to the following policies:
Accept All - The GK will enable all requesting endpoints to register dynamically.
Predefined Only - The GK wil…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.7.2.1.9

gkGenZoneId

Zone Identifier: 1 or 2 digits, (0-9)(1-9).

OctetStringr/w

.1.3.6.1.4.1.164.3.1.7.2.1.10

gkEndpTable

table

.1.3.6.1.4.1.164.3.1.7.3 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk gkEndpTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::gkEndpTable'

Table containing the Endpoints that are registered (statically & Dynamically)
with the current GK.

gkEndpEntry row .1.3.6.1.4.1.164.3.1.7.3.1

An entry in table gkEndpTable.

Indexes

No indexes recorded

Column Syntax OID

gkEndpAliasTag

Alias Tag of the Endpoint.

MULTI-MEDIA-MIB-TCMmAliasTag

Type Values:

0	other
1	e164
2	h323Id
3	urlId
4	transportId
5	emailId
6	partyNumber

.1.3.6.1.4.1.164.3.1.7.3.1.1

gkEndpAlias

Alias of the Endpoint.

MULTI-MEDIA-MIB-TCMmAliasAddress

Type Constraints:
range: 1..512

.1.3.6.1.4.1.164.3.1.7.3.1.2

gkEndpRowStatus

The row status of the entry. This object is required to create
or delete rows remotely by a manager.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.3.1.7.3.1.3

gkEndpAddressTag

Address Tag of Endpoint.

MULTI-MEDIA-MIB-TCMmTAddressTagr/w

Type Values:

0	other
1	ipv4
2	ipv6
3	ipx
4	nsap
5	netbios

.1.3.6.1.4.1.164.3.1.7.3.1.4

gkEndpAddress

Address of Endpoint.

SNMPv2-TCTAddressr/w

Type Constraints:
range: 1..255

Description:

Denotes a transport service address.

A TAddress value is always interpreted within the context of a
TDomain value. Thus, each definition of a TDomain value must
be accompanied by a definition of a textual co…

.1.3.6.1.4.1.164.3.1.7.3.1.5

gkEndpID

Endpoint Identifier.

MULTI-MEDIA-MIB-TCMmEndpointIDr/w

Type Constraints:
range: 1..128

.1.3.6.1.4.1.164.3.1.7.3.1.6

gkEndpType

This parameter shows whether the current endpoint is a GW or Terminal or
any other type of H.323 endpoint.

MULTI-MEDIA-MIB-TCMmH323EndpointTyper/w

.1.3.6.1.4.1.164.3.1.7.3.1.7

gkEndpQ931Port

Q.931 Port no.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.7.3.1.8

gkEndpDistance

Distance from the current endpoint to the GateKeeper with which it is
Registered.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.7.3.1.9

gkEndpRegMode

This parameter shows whether the Endpoint Registered Dynamically or Statically.

Enumeration

.1.3.6.1.4.1.164.3.1.7.3.1.10

gkEndpSetOnline

This parameter shows whether the endpoint will always be online or whether it
will be on line upon Dynamic Registration only.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.7.3.1.11

gkEndpStatus

This parameter shows whether the endpoint is currently online.

Enumeration

.1.3.6.1.4.1.164.3.1.7.3.1.12

gkNeighbTable

table

.1.3.6.1.4.1.164.3.1.7.4 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk gkNeighbTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::gkNeighbTable'

Table of GateKeepers that are Neighbors of the current Gatekeeper.

gkNeighbEntry row .1.3.6.1.4.1.164.3.1.7.4.1

An entry in table gkNeighbTable.

Indexes

No indexes recorded

Column Syntax OID

gkNeighbAddressTag

Tag of GK or GW address.

MULTI-MEDIA-MIB-TCMmTAddressTag

Type Values:

0	other
1	ipv4
2	ipv6
3	ipx
4	nsap
5	netbios

.1.3.6.1.4.1.164.3.1.7.4.1.1

gkNeighbAddress

Address of GK or GW.

SNMPv2-TCTAddress

Type Constraints:
range: 1..255

Description:

.1.3.6.1.4.1.164.3.1.7.4.1.2

gkNeighbRowStatus

The row status of the entry. This object is required to create
or delete rows remotely by a manager.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.3.1.7.4.1.3

gkNeighbLeadingAlias

This is the Leading Alias Address (Zone Prefix) that will be dialed in order to reach
the specific neighbor.

MULTI-MEDIA-MIB-TCMmAliasAddressr/w

Enumerated Values:

1	gateway
2	localEntries

Type Constraints:
range: 1..512

.1.3.6.1.4.1.164.3.1.7.4.1.4

gkNeighbDistance

Distance between the local GateKeeper and the Neighbor GateKeeper.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	gateway
2	localEntries

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.7.4.1.5

gkNeighbDescription

ASCII String Description for identifying the Neighbor.

MULTI-MEDIA-MIB-TCMmGatekeeperIDr/w

Enumerated Values:

2	no
3	yes

Type Constraints:
range: 1..128

.1.3.6.1.4.1.164.3.1.7.4.1.6

gwGenTable

table

.1.3.6.1.4.1.164.3.1.7.5 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk gwGenTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::gwGenTable'

General parameters for the VOIP GateWay.

gwGenEntry row .1.3.6.1.4.1.164.3.1.7.5.1

An entry in table gwGenTable.

Indexes

No indexes recorded

Column Syntax OID

gwGenGwId

A character string of up to 20 characters identifying the gateway.

MULTI-MEDIA-MIB-TCMmEndpointIDr/w

Type Constraints:
range: 1..128

.1.3.6.1.4.1.164.3.1.7.5.1.1

gwGenQ931Port

The Q.931 port no. of the Gateway.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.7.5.1.2

gwGenRasPort

The RAS port no. of the Gateway.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.7.5.1.3

gwGenMode

GW Mode:
disable - The GW is not activated.
cvsIp - CVS is a Compressed Voice System.
The GW will compress voice calls at a ratio of
16 to 1. 16 time slots of E1/T1 will be compressed into
…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.7.5.1.4

gwGenVoipExtension

This is the extension number of the VOIP protocol.
It is used for the Voice card to identify the calls made through the VoIP card.
The user may choose an arbitrary value for this field, the only restriction is that
ther…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.7.5.1.5

gwGenRemGwAddress

Defines the remote gateway address (IP + port). It is important for gateway
to gateway connection.

SNMPv2-TCTAddressr/w

Type Constraints:
range: 1..255

Description:

.1.3.6.1.4.1.164.3.1.7.5.1.6

gwGenMaxConnections

MAX no. of connections enabled by the GW.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.7.5.1.7

gwGenTOS

OctetStringr/w

.1.3.6.1.4.1.164.3.1.7.5.1.8

gwGenBackupGkAddr

Defines the backup gatekeeper address (IP + port).
When the backup GK is active, all the calls will be routed to it and it
will be responsible for their address translation.
The first GK address is defined in the standa…

SNMPv2-TCTAddressr/w

Type Constraints:
range: 1..255

Description:

.1.3.6.1.4.1.164.3.1.7.5.1.9

gwGenTimeToRegister

The GW should register every 'Time to Register' seconds with the GK.
The 'Time to Register' range is from 0 to 900 seconds in intervals of 60 seconds.
0 means Never.
When the GK becomes active the Gateways that are …

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.1.7.5.1.10

radH245ConfigTable

table

.1.3.6.1.4.1.164.3.1.7.6 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radH245ConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radH245ConfigTable'

This table contains information about H.245 configuration parameters.
It is a list of configuration parameter entries.
The number of entries equals to the number of H.245 stacks in a system.

radH245ConfigEntry row .1.3.6.1.4.1.164.3.1.7.6.1

It contains objects that describe the H.245 configuration parameters.

Indexes

No indexes recorded

Column	Syntax	OID
h245MaxJitter Maximum peak to peak delivery (in miliseconds) of audio packets to the transport layer that the transmitter shall cause.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.7.6.1.1`
h245Tunneling This variable enables or disables the usage of Tunneling.	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.7.6.1.2`

rtpMultiplexTable

table

.1.3.6.1.4.1.164.3.1.7.7 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk rtpMultiplexTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::rtpMultiplexTable'

RTP Multiplexing table.
RTP Multiplexing: In IP telephony system, the addition of packet headers,
including IP, UDP and RTP headers, increases the header overhead, decreasing
efficient transmission. Also, because of large numbers of short voice
packets flowing into the network, Internet load increases, eventually
resulting in large delay and packet loss. RTP Multiplexing is a way to send
multiple RTP packets between a pair of Gateways, with a single
IP frame. This will reduces the header overhead and decreases delay by
enabling voice transmission with fewer packets.

rtpMultiplexEntry row .1.3.6.1.4.1.164.3.1.7.7.1

An entry in table rtpMultiplexTable.

Indexes

No indexes recorded

Column	Syntax	OID
rtpMultiplexedRtp RTP Multiplexing is a way to send multiple RTP packets with a single IP frame. This will reduce the header overhead and decrease the delay by enabling voice transmission with fewer packets. The option of this field are:…	Enumerationr/w	`.1.3.6.1.4.1.164.3.1.7.7.1.1`
rtpMultiplexFrameSize Defines the maximum size in Bytes of the multiplexed frame. In some cases this must be limited to avoid IP fragmentation, which makes the multiplexing useless, and can also decrease the damage in case of the frame loss.…	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.7.7.1.2`
rtpMultiplexInterval Defines the maximum amout of time (msec.) between multiplexed frames that are sent. Legal values: 10-90 msec.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.7.7.1.3`
rtpMultiplexPcktRedundancy Defines the the number of times each voice frame should be transmitted. At present legal values are: 1-4.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.1.7.7.1.4`

voipTariffServerTable

table

.1.3.6.1.4.1.164.3.1.7.8.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk voipTariffServerTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::voipTariffServerTable'

VoIP Tariff Server table.

voipTariffServerEntry row .1.3.6.1.4.1.164.3.1.7.8.1.1

An entry in table voipTariffServerTable.

Indexes

voipServiceCfgIdx voipServicePrtIdx voipServiceType

Column Syntax OID

voipTariffServerCnfgIdx

This object indicates the Index of the Configuration (1..255) being
accessed ; Index=255 relates to the Temporary Configuration.
Set is allowed only to the Temporary Configuration.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.8.1.1.1

voipTariffServerIdx

This object indicates the Index of the Tariff Server being
accessed (1, 2).

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.8.1.1.2

voipTariffServerIpAddress

This object defines the IP Address of the Tariff Server.

RFC1155-SMIIpAddressr/w

Enumerated Values:

1	callForward
2	callTransfer
3	callerIdRestriction
4	callHold

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.1.7.8.1.1.3

voipTariffServerPort

This object defines the used TCP/UDP port of the Tariff Server.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.8.1.1.4

radSipCommonCfgTable

table

.1.3.6.1.4.1.164.3.1.7.9.1.1.1.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radSipCommonCfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radSipCommonCfgTable'

SIP Common Configuration table.
This table contains the common configuration objects
applicable to all SIP entities.

radSipCommonCfgEntry row .1.3.6.1.4.1.164.3.1.7.9.1.1.1.1.1

A row of SIP Common Configuration table.

Indexes

No indexes recorded

Column Syntax OID

radSipCommonCfgIdx

The index of the table.

This object might represent the Configuration Index (1..100) being accessed;
Index=255 relates to the TmpCnfg.
For devices with multiple configurations, Set is permitted to TmpCnfg…

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.1.1.1.1.1.1

radSipCommonCfgListenPort

This object represents the SIP Listening Port number.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	noRestriction
2	restrictAllCalls
3	restrictNextCall

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.1.1.1.1.1.2

radSipCommonCfgRtpBaseUdpPort

This object represents the RTP Base UDP Port number.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.1.1.1.1.1.3

radSipCommonCfgRtpIpTos

This object represents the TOS byte value
that will be written in the IP header for RTP packets only.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.1.1.1.1.1.4

radSipRegCfgTable

table

.1.3.6.1.4.1.164.3.1.7.9.1.2.1.1 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radSipRegCfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radSipRegCfgTable'

SIP Registrar Configuration table.

radSipRegCfgEntry row .1.3.6.1.4.1.164.3.1.7.9.1.2.1.1.1

A row of SIP Registrar Configuration table.

Indexes

No indexes recorded

Column Syntax OID

radSipRegCfgIdx

The first index of the table.

This object might represent the Configuration Index (1..100) being accessed;
Index=255 relates to the TmpCnfg.
For devices with multiple configurations, Set is permitted to T…

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.1.2.1.1.1.1

radSipRegIdx

This object represents the Registrar Index.

SNMPv2-SMIUnsigned32

Enumerated Values:

1	callForwardUnconditional
2	callForwardNoReply
3	callForwardBusy
4	callForwardDeactivation
5	callTransfer
6	callerIdRestrictNextCall
7	callerIdRestrictAllCalls
8	callerIdRestrictDeactivation

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.1.2.1.1.1.2

radSipRegActivation

This object allows the user to activate the Registrar.

If changed from enable(3) to disable(2) -
device will be disconnected from server (stop sending renewal messages).
If changed from disable(2) to e…

Enumerationr/w

.1.3.6.1.4.1.164.3.1.7.9.1.2.1.1.1.3

radSipRegAddr

This object represents the Registrar's IP/URL Address.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.3.1.7.9.1.2.1.1.1.4

radSipRegUdpPort

This object represents the Registration's Destination UDP Port number.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.1.2.1.1.1.5

radSipRegRenewalTimer

This object represents the Registration's Renewal Timer, in seconds.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.1.2.1.1.1.6

radSipRegDomain

This object represents the User Agent's Domain Name.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.3.1.7.9.1.2.1.1.1.7

radSipRegMode

This object indicates the Registration Mode:
gateway(1) - one registration for the device
localEntries(2) - number of registrations are defined according to
the number of local entries.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disabled
3	ms16
4	ms32

.1.3.6.1.4.1.164.3.1.7.9.1.2.1.1.1.8

radSipRegUserDefinition

This object indicates the User configuration:
gateway(1) - single user configuration for the device
localEntries(2) - different user configuration for each local entry.

This object is irrelevant when…

Enumerationr/w

Enumerated Values:

1	group1
2	group2
3	group3
4	group4
5	group5
6	group6
7	group7
8	group8
255	notApplicable

.1.3.6.1.4.1.164.3.1.7.9.1.2.1.1.1.9

radSipRegCallWithoutReg

This object indicates whether a call is enabled without registration.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	tieTrunk
3	tieInvert
4	casTrans
5	userDefined
6	ccsTrans
7	noSignaling

.1.3.6.1.4.1.164.3.1.7.9.1.2.1.1.1.10

radSipRegUserParams

This object indicates the User's parameters.
This object is irrelevant when radSipRegUserDefinition = localEntries(2).

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.3.1.7.9.1.2.1.1.1.11

radSipRegRowStatus

This object enables the user to create/delete entries in this table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.3.1.7.9.1.2.1.1.1.12

voipNetRoutTable

table

.1.3.6.1.4.1.164.3.1.7.9.2 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk voipNetRoutTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::voipNetRoutTable'

Network Routing table.

voipNetRoutEntry row .1.3.6.1.4.1.164.3.1.7.9.2.1

A row of Network Routing table.

Indexes

No indexes recorded

Column Syntax OID

voipNetRoutCfgIdx

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.2.1.1

voipNetRoutPrefix

This object represents the prefix number.
This prefix can include non-decimal digits, such as * or #.

The default route will be represented by an empty prefix.

SNMP-FRAMEWORK-MIBSnmpAdminString

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.3.1.7.9.2.1.2

voipNetRoutRowStatus

This object enables the user to create/delete entries in this table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.3.1.7.9.2.1.3

voipNetRoutMinDigits

This object indicates the Minimum number of digits.

SNMPv2-SMIUnsigned32r/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.1.7.9.2.1.4

voipNetRoutMaxDigits

This object indicates the Maximum number of digits.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	notApplicable
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.2.1.5

voipNetRoutAddr

This object indicates the route's IP/URL Address.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.3.1.7.9.2.1.6

voipNetRoutUdpPort

This object indicates the route's destination UDP port number.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.2.1.7

voipNetRoutOutboundProxySupport

This object indicates whether the Outbound Proxy is supported.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.7.9.2.1.8

voipNetRoutOutboundProxyAddr

This object indicates the Outbound Proxy's IP/URL Address.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.3.1.7.9.2.1.9

voipNetRoutOutboundProxyUdpPort

This object indicates the Outbound Proxy UDP port number.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	psA
2	psB
3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.2.1.10

voipNumManipTable

table

.1.3.6.1.4.1.164.3.1.7.9.3 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk voipNumManipTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::voipNumManipTable'

Numbering Manipulation table.

voipNumManipEntry row .1.3.6.1.4.1.164.3.1.7.9.3.1

A row of Numbering Manipulation table.

Indexes

No indexes recorded

Column Syntax OID

voipNumManipCfgIdx

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.3.1.1

voipNumManipTypeId

This object represents the Numbering Manipulation's Type ID.
Type ID represents a unique Type, which can be different for each device.

For Vmux-300 devices -

Type ID Manipulated Number …

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.3.1.2

voipNumManipRuleIdx

This object represents the Rule index.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.3.1.3

voipNumManipRowStatus

This object enables the user to create/delete entries in this table.

SNMPv2-TCRowStatusr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

Description:

.1.3.6.1.4.1.164.3.1.7.9.3.1.4

voipNumManipOriginalNumber

This object represents the original number (before manipulation).

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6
7	exPrt7
8	exPrt8
9	exPrt9
10	exPrt10
11	exPrt11
12	exPrt12

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.3.1.5

voipNumManipNewNumber

This object represents the new number (after manipulation).

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	unknown
2	v35
3	rs422

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.3.1.6

voipServiceTable

table

.1.3.6.1.4.1.164.3.1.7.9.4.1 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk voipServiceTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::voipServiceTable'

Services table.

voipServiceEntry row .1.3.6.1.4.1.164.3.1.7.9.4.1.1

A row of Service table.

Indexes

No indexes recorded

Column Syntax OID

voipServiceCfgIdx

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.4.1.1.1

voipServicePrtIdx

This object represents the Port Index.
When irrelevant, value will be 1.

SNMPv2-SMIUnsigned32

Enumerated Values:

2	voice
3	idle
4	fax
5	vbd

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.4.1.1.2

voipServiceType

This object represents the Service's Type.

Enumeration

Enumerated Values:

2	present
3	overlapReceive
4	incoming
5	receive
6	initiated
7	overlapSend
8	outGoingProceed
9	callDeliver
10	active
11	disconnectIndicate
12	releaseRequest
13	disconnectReq
14	notActive

.1.3.6.1.4.1.164.3.1.7.9.4.1.1.3

voipServiceSupport

This object represents the Service's support.

Enumerationr/w

.1.3.6.1.4.1.164.3.1.7.9.4.1.1.4

voipServiceCallForwardType

This object represents the Call Forward Type.
It is relevant only for voipServiceType = callForward(1).

Enumerationr/w

.1.3.6.1.4.1.164.3.1.7.9.4.1.1.5

voipServiceCallForwardPhoneNo

This object represents the Phone Number to be forwarded.
It is relevant only for voipServiceType = callForward(1).

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.3.1.7.9.4.1.1.6

voipServiceCallForwardNoReplyTimeout

This object indicates the No Reply Timeout in seconds.
It means how many seconds with no reply should pass
so that this period of time will be considered as No Reply.
It is relevant only for voipServiceType = callForwar…

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	notApplicable
2	incoming
3	outgoing

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.4.1.1.7

voipServiceCallerIdType

This object represents the Caller ID Type.
It is relevant only for voipServiceType = callerIdRestriction(3).

Enumerationr/w

.1.3.6.1.4.1.164.3.1.7.9.4.1.1.8

voipServiceCallerIdDisplayString

This object represents the string that should be displayed
when no restriction is applied.
It is relevant only for voipServiceType = callerIdRestriction(3).

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.3.1.7.9.4.1.1.9

voipFeatureTable

table

.1.3.6.1.4.1.164.3.1.7.9.4.2 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk voipFeatureTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::voipFeatureTable'

Feature table.

voipFeatureEntry row .1.3.6.1.4.1.164.3.1.7.9.4.2.1

A row of Feature table.

Indexes

No indexes recorded

Column Syntax OID

voipFeatureCfgIdx

SNMPv2-SMIUnsigned32

Enumerated Values:

1	exPrt1
2	exPrt2

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.4.2.1.1

voipFeaturePrtIdx

This object represents the Port Index.
When irrelevant, value will be 1.

SNMPv2-SMIUnsigned32

Enumerated Values:

1	unknown
2	noUse
3	nmsSlip
4	nmsPpp
5	muxSlip
6	muxPpp
7	terminal

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.1.7.9.4.2.1.2

voipFeatureType

This object represents the Feature's Type.

Enumeration

Enumerated Values:

1	r300Bps
2	r1200Bps
3	r2400Bps
4	r4800Bps
5	r9600Bps
6	r19200Bps
7	r38400Bps
8	r57600Bps
9	r115200Bps

.1.3.6.1.4.1.164.3.1.7.9.4.2.1.3

voipFeatureKeypadString

This object represents the Feature's Keypad string.
This string is a combination of digits, * and #.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Enumerated Values:

1	dataBits7Bits
2	dataBits8Bits

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.3.1.7.9.4.2.1.4

mdlPbxFramerCnfgTable

table

.1.3.6.1.4.1.164.3.2.2.1.1.1 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlPbxFramerCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlPbxFramerCnfgTable'

This table contains parameters relevant to a module belonging to
a digital voice system, except mdlPbxFraEnhEcho which is relevant
also for analog cards.

mdlPbxFramerCnfgEntry row .1.3.6.1.4.1.164.3.2.2.1.1.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

mdlPbxFraCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

SNMPv2-SMIInteger32

Enumerated Values:

1	none
2	rip2

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.2.1.1.1.1.1

mdlPbxFraSltIdx

The slot relevant to this module.

Enumeration

Enumerated Values:

1	notApplicable
2	disabled
3	enabled

.1.3.6.1.4.1.164.3.2.2.1.1.1.1.2

mdlPbxFraEnhEcho

Refers to external ports of an analogue module
and to the internal ports of the other mvc4 types
of modules.
ms16(3) means that the four voice ports have enhanced
echo of 16ms.
ms32(4) means that the two first p…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.2.1.1.1.1.3

mdlPbxFraTSGroupAss

In case of T1 modules:
group1=(1,2,3,4), ...., group6=(21,22,23,24)
while in case of E1 modules:
- If prtExPh1MlLineType=g732sE1 or g732sE1CRC:
group1=(1,2,3,4),..,group4=(13,14,15,17),
group5=(18,19,20,2…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.2.1.1.1.1.4

mdlPbxFraSignalMode

Refers to the signaling mode of the Framer module.
tieTrunk(2), tieInvert(3), casTrans(4) are standard
coding of the signaling protocol.

casTrans(4) is Channel Associated Signaling (the signaling is withi…

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.2.1.1.1.1.5

mdlPbxFraSignalVector

In the case of mdlPbxFraSignalMode = userDefined(5), this
field defines the A,B,C Bits. D bit is supplied for future
versions.
Bit 1 = Bit A ON Hook - Local
Bit 2 = Bit B ON Hook - Local
Bit 3 = Bit C ON Hook - Lo…

OctetStringr/w

Enumerated Values:

1	notApplicable
3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.2.1.1.1.1.6

mdlPbxFraSignalMask

In the case of mdlPbxFraSignalMode = userDefined(5), this
field defines the 'don't care' A,B,C Bits. D bit is supplied
for future versions.
Bit 1 = Bit A ON Hook - Local
Bit 2 = Bit B ON Hook - Local
Bit 3 = Bit C …

OctetStringr/w

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6
7	exPrt7
8	exPrt8
9	exPrt9
10	exPrt10
11	exPrt11
12	exPrt12
13	exPrt13
14	exPrt14
15	exPrt15
16	exPrt16
17	exPrt17
18	exPrt18
101	inPrt1
102	inPrt2
103	inPrt3
104	inPrt4
105	inPrt5
106	inPrt6
107	inPrt7
108	inPrt8
109	inPrt9
110	inPrt10
111	inPrt11
112	inPrt12
113	inPrt13
114	inPrt14
115	inPrt15
116	inPrt16
117	inPrt17
118	inPrt18
119	inPrt19
120	inPrt20
121	inPrt21
122	inPrt22
123	inPrt23
124	inPrt24
125	inPrt25
126	inPrt26
127	inPrt27
128	inPrt28
129	inPrt29
130	inPrt30
131	inPrt31
132	inPrt32
133	inPrt33
134	inPrt34
135	inPrt35
136	inPrt36
137	inPrt37
138	inPrt38
139	inPrt39
140	inPrt40
141	inPrt41
142	inPrt42
143	inPrt43
144	inPrt44
145	inPrt45
146	inPrt46
147	inPrt47
148	inPrt48
149	inPrt49
150	inPrt50
151	inPrt51
152	inPrt52
153	inPrt53
154	inPrt54
155	inPrt55
156	inPrt56
157	inPrt57
158	inPrt58
159	inPrt59
160	inPrt60
161	inPrt61
162	inPrt62
163	inPrt63
164	inPrt64
165	inPrt65
166	inPrt66
167	inPrt67
168	inPrt68
169	inPrt69
170	inPrt70
171	inPrt71
172	inPrt72
173	inPrt73
174	inPrt74
175	inPrt75
176	inPrt76
177	inPrt77
178	inPrt78
179	inPrt79
180	inPrt80
181	inPrt81
182	inPrt82
183	inPrt83
184	inPrt84

.1.3.6.1.4.1.164.3.2.2.1.1.1.1.7

mdlPbxFraFramerSlot

Slot where is sitting the Framer.

Enumerationr/w

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.2.2.1.1.1.1.8

mdlPbxFraSignaling

Signaling - describes the way the signaling ABCD bits pass from the
local extension to the remote extension and vice-versa.

endToEnd = the signaling ABCD bits pass without change from local to
remote exte…

Enumerationr/w

Enumerated Values:

2	esfT1
3	sfT1
4	g732nE1
5	g732nE1CRC
6	g732sE1
7	g732sE1CRC
8	g732unframed
9	e1Unframed
101	framed

.1.3.6.1.4.1.164.3.2.2.1.1.1.1.9

mdlPbxFraTransSigTs

This is the Time Slot that is used for Transparent CCS signaling.
The values of this TS are 1-24 for T1 & 1-31 for E1.
The default for E1 is 16 & for T1 it is 24. If no signaling is used then
the TS should be 255 (None).

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	b7T1
2	b8zsT1
3	transT1
4	hdb3E1
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.2.1.1.1.1.10

mdlProtIpTable

table

.1.3.6.1.4.1.164.3.2.2.1.2 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlProtIpTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlProtIpTable'

This table contains Protected IP Addresses for ML-IP cards
when working in IP Ring Mode.

mdlProtIpEntry row .1.3.6.1.4.1.164.3.2.2.1.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

mdlProtIpCnfgIdx

This attribute indicates the Idx of the Cnfg being accessed.
Idx 255 relates to the TmpCnfg.
For Agents having several configuration, Write operation is
allowed only to the Temporary Configuration.

Integer32

Enumerated Values:

1	notApplicable
2	txGain0db
3	txGain7dot5db
4	txGain15db
5	txGain22dot5db

.1.3.6.1.4.1.164.3.2.2.1.2.1.1

mdlProtIpSlotIdx

This attribute indicates a unique slot position where
the module is inserted.
In the 2104 Unit the entries io6(10)..io16) are not valid.

Enumeration

Enumerated Values:

1	notApplicable
2	low26dBm
3	high36dBm
4	shortHaul
5	longHaul
6	low15dbm

.1.3.6.1.4.1.164.3.2.2.1.2.1.2

mdlProtIpAddress

A Protected IP address.

RFC1155-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.2.2.1.2.1.3

mdlProtIpRowStatus

This parameter allows creating/deleting entries of this table.

SNMPv2-TCRowStatusr/w

Enumerated Values:

1	linkA
2	linkB
3	none
255	notApplicable

Description:

.1.3.6.1.4.1.164.3.2.2.1.2.1.4

mdlStatTable

table

.1.3.6.1.4.1.164.3.2.2.2.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlStatTable'

A table.

mdlStatEntry row .1.3.6.1.4.1.164.3.2.2.2.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

mdlStatSltIdx

A unique number to identify a slot position in the mux.
In the 2104 Unit the entries psB(2),clB(4),io6(10)..io12(16)
are not valid.

Enumeration

Enumerated Values:

1	exPrt1
2	exPrt2
101	inPrt1
255	notApplicable

.1.3.6.1.4.1.164.3.2.2.2.1.1.1

mdlStatHostIP

The host interface IP address when DHCP Client=Yes.
This object is relevant only when DHCP Client=Yes

RFC1155-SMIIpAddress

Enumerated Values:

1	notApplicable
2	response
3	command

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.2.2.2.1.1.2

mdlStatHostMask

The host interface subnet mask when DHCP Client=Yes.
This object is relevant only when DHCP Client=Yes

RFC1155-SMIIpAddress

Enumerated Values:

2	off
3	fdlOrTs0
4	dedicatedTs
5	dedicatedPpp
6	dedicatedFr
255	notApplicable

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.2.2.2.1.1.3

mdlStatDefaultGateway

Default Gateway's IP Address when DHCP Client=Yes.
This object is relevant only when DHCP Client=Yes

RFC1155-SMIIpAddress

Enumerated Values:

1	notApplicable
2	r4k
3	r8k
4	r12k
5	r16k
6	r32k
7	r64k
8	r20k

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.2.2.2.1.1.4

prtSExHsfStatTable

table

.1.3.6.1.4.1.164.3.2.3.1.6 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtSExHsfStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtSExHsfStatTable'

A table.

prtSExHsfStatEntry row .1.3.6.1.4.1.164.3.2.3.1.6.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtSExHsfSltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io16) are not valid.

Enumeration

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
101	inPrt1
102	inPrt2
103	inPrt3
104	inPrt4
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.1.6.1.1

prtSExHsfPrtIdx

This attribute indicates a unique port number.

Enumeration

Constraints:
range: 1-99

.1.3.6.1.4.1.164.3.2.3.1.6.1.2

prtSExHsfInterfaceTyp

This attribute indicates a unique interface type of a
selected port.

Enumeration

Enumerated Values:

1	none
2	rip2
3	proprietary
4	proprietaryNoNmsTx

.1.3.6.1.4.1.164.3.2.3.1.6.1.3

prtSExHsfRts

This attribute indicates a unique RTS control signal state.

Enumeration

Enumerated Values:

1	notApplicable
2	csu
3	dsu
4	ltu

.1.3.6.1.4.1.164.3.2.3.1.6.1.4

prtIsdnStatusTable

table

.1.3.6.1.4.1.164.3.2.3.1.16 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtIsdnStatusTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtIsdnStatusTable'

This table contains ISDN Statistics parameters that do not appear
in the standard MIBs or for agents that don't support the standard Index
of Call Set Up Time.

prtIsdnStatusEntry row .1.3.6.1.4.1.164.3.2.3.1.16.1

Entries for ISDN Statistics parameters that do not appear in the standard MIBs
or for agents that don't support the standard Index of Call Set Up Time.

Indexes

No indexes recorded

Column Syntax OID

prtIsdnStatusDspMode

The DSP can be in one of the following Modes:
Voice, Idle, Fax, Voice Band Data (VBD)- Modem.

Enumeration

Enumerated Values:

1	notApplicable
2	unbalanced
3	balanced

.1.3.6.1.4.1.164.3.2.3.1.16.1.1

prtIsdnStatusCallState

The state that the current call is in.

Enumeration

Enumerated Values:

2	disable
3	annexA
4	annexB

.1.3.6.1.4.1.164.3.2.3.1.16.1.2

prtIsdnStatusCallingNumber

This is the local Number (ISDN Address) associated with this entry.

SNMPv2-TCDisplayString

Enumerated Values:

1	notApplicable
2	aAndB
3	cAndD

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.2.3.1.16.1.3

prtIsdnStatusCalledNumber

This is the remote Number (ISDN Address) associated with this entry.

SNMPv2-TCDisplayString

Enumerated Values:

2	disable
3	enable

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.2.3.1.16.1.4

prtIsdnStatusCalledIP

This is the remote IP Address associated with this entry.

RFC1155-SMIIpAddress

Enumerated Values:

1	notApplicable
2	normal
3	advanced

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.2.3.1.16.1.5

prtIsdnStatusCallDirection

Attribute indicating the Direction of the Call.
The value of notApplicable will be used for example when
prtIsdnStatusCallState = notActive(14).

Enumeration

.1.3.6.1.4.1.164.3.2.3.1.16.1.6

prtExClCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.1.1 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExClCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExClCnfgTable'

A table.

prtExClCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.1.1.1

All the entries at this table are identical (have the same
value) for all the configurations (1..100) except the
TmpCnfg.
The write operation into the Table Objects is valid only
to the TmpCnfg entry.

Indexes

prtExPh1MlTsCnfgIdx prtExPh1MlTsSltIdx prtExPh1MlTsPrtIdx prtExPh1MlTsIdx

Column Syntax OID

prtExClCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.1.1.1.1

prtExClSltIdx

This attribute indicates a unique slot position where
the card is inserted. Because the second Cl is only for
redundancy, all the parameters are identical in the two
modules, i.e. change of any parameter in one module…

Enumeration

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.1.1.1.2

prtExClPrtIdx

This attribute indicates a unique port number.

Enumeration

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6
7	exPrt7
8	exPrt8
9	exPrt9
10	exPrt10
11	exPrt11
12	exPrt12
13	exPrt13
14	exPrt14
15	exPrt15
16	exPrt16
17	exPrt17
18	exPrt18
101	inPrt1
102	inPrt2
103	inPrt3
104	inPrt4
105	inPrt5
106	inPrt6
107	inPrt7
108	inPrt8
109	inPrt9
110	inPrt10
111	inPrt11
112	inPrt12
113	inPrt13
114	inPrt14
115	inPrt15
116	inPrt16
117	inPrt17
118	inPrt18
119	inPrt19
120	inPrt20

.1.3.6.1.4.1.164.3.2.3.2.1.1.1.3

prtExClUsage

This attribute indicates what is the usage of the port.

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.1.1.1.4

prtExClRate

This attribute indicates the operation rate of the port.

Enumeration

Enumerated Values:

1	unknown
2	noConnect
4	split
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.1.1.1.5

prtExClDataBits

This attribute indicates the number of data bits in async
frame

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.1.1.1.6

prtExClParity

This attribute indicates if the parity operation mode in
async frame

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.1.1.1.7

prtExClStopBits

This attribute indicates the minimum number of stop bits in
the tx async frame

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.1.1.1.8

prtExClRoutingProtocol

This attribute indicates the routing protocol of the port.
When prtExClUsage is nmsSlip or nmsPpp - all values are
applicable .
Else - only 'none' is applicable.

Enumeration

Enumerated Values:

1	none
2	localLoop
3	remoteLoop
8	remoteBert
9	localToneInjection
18	remoteToneInjection
30	localBert
254	split
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.1.1.1.9

prtExClEnabled

This attribute indicates if Ethernet port of CL
is enabled or not for management.
It is applicable only on the ETH port of the CL, when the
MP includes an ML-IP card.
disabled - will happen when there is Inband Managem…

Enumeration

Enumerated Values:

2	noConnect
3	data
4	voice
5	cas
6	ss7
7	transparent
8	data2
9	data3
10	data4
11	ss7n2
12	hdlcV2Compatible
13	subCh1
14	subCh2
15	subCh3
16	subCh4
17	subCh5
18	subCh6
19	subCh7
20	subCh8
21	trau
22	qmux
23	dynamic
24	signaling
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.1.1.1.10

prtExPh1MlCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.2.1 · 1 row entry · 32 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExPh1MlCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExPh1MlCnfgTable'

- For products supporting more than one configuration, the write operation 
into the Table is valid only to the TmpCnfg entry.
- For products that do not support configurations, the write operation 
into the Table will be to prtExPh1MlCnfgIdx=1.

prtExPh1MlCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.2.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtExPh1MlCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

Enumerated Values:

1	hdlc
2	transparent
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.1

prtExPh1MlSltIdx

This attribute indicates a unique slot position where
the module is inserted.
In the ?004 Unit the entries io6(10)..io16) are not valid.
For the Vmux2100 Main Board notApplicable (1) is used.

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.2

prtExPh1MlPrtIdx

This attribute indicates a unique port number.
MP-2100/2200:
MTML-1/E1 and MTML-1/T1 cards have only one external interface.
inPrt1, inPrt2 - for MTML-H/2E1 and HSH cards.
inPrt1..inPrt4 - for MTML-E2 and MSL-4 cards.
…

Enumeration

Enumerated Values:

1	notApplicable
2	r16Kbps
3	r32Kbps
4	r64Kbps
5	r8Kbps
6	auto

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.3

prtExPh1MlConnect

This attribute indicates whether the port should be considered
in any of the mux algorithms. It also affects all the card
considerations because it may indicate that the module has only
one physical interface.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.4

prtExPh1MlLineType

This attribute is the line type parameter for T1/E1 interface.
The user should select only the values which are relevant
to the specific port:
(2),(3), (8) - for T1 port
(4)..(7), (9) - for E1 port.
(101) framed - …

Enumerationr/w

Enumerated Values:

1	notApplicable
3	p1
4	p2
5	p3
6	p4
7	p5

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.5

prtExPh1MlLineCode

This attribute is the line code parameter used for T1/E1
interface.
The user should select only the parameters which are relevant
to the specific card:
T1 line code parameters for MPH.1/T1
E1 line code parameters for MP…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.6

prtExPh1MlLineLen

This attribute is the line length parameter used only for T1/DSU
interfaces.
lenXXXpXXXft = len-XXX-XXXft.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.7

prtExPh1MlRestoreTime

The time passing from the disappearance of the loss of
synchronization condition (red alarm) to the restoration of
normal service. The options 1secFast(2) and 10sec62411(3)
for E1 interfaces are proprietary implementati…

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.8

prtExPh1MlTxGain

This attribute is the tx gain parameter used only for
T1/CSU interfaces.

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.9

prtExPh1MlRxSensitivity

This attribute is the rx line sensitivity parameter.
low26dBm, high36dBm - applicable for T1-CSU
shortHaul, longHaul - applicable for MTML-4 cards
low15dbm was added for vmux110/210 T1 ports.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.10

prtExPh1MlIdleCode

Determines the code for transmission in empty time slots.
Type value(00-FFH), Excluding 0H,8H,10H,12H,21H,24H,42H,49H,
84H,92H

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.11

prtExPh1MlTdmTrunk

This attribute indicates whether the port is used to transfer
TDM cards data and through which Bus.

Enumerationr/w

Enumerated Values:

1	r1x56eq56Kbps
2	r1x64eq64Kbps
3	r2x56eq112Kbps
4	r2x64eq128Kbps
5	r3x56eq168Kbps
6	r3x64eq192Kbps
7	r4x56eq224Kbps
8	r4x64eq256Kbps
9	r5x56eq280Kbps
10	r5x64eq320Kbps
11	r6x56eq336Kbps
12	r6x64eq384Kbps
13	r7x56eq392Kbps
14	r7x64eq448Kbps
15	r8x56eq448Kbps
16	r8x64eq512Kbps
17	r9x56eq504Kbps
18	r9x64eq576Kbps
19	r10x56eq560Kbps
20	r10x64eq640Kbps
21	r11x56eq616Kbps
22	r11x64eq704Kbps
23	r12x56eq672Kbps
24	r12x64eq768Kbps
25	r13x56eq728Kbps
26	r13x64eq832Kbps
27	r14x56eq784Kbps
28	r14x64eq896Kbps
29	r15x56eq840Kbps
30	r15x64eq960Kbps
31	r16x56eq896Kbps
32	r16x64eq1024Kbps
33	r17x56eq952Kbps
34	r17x64eq1088Kbps
35	r18x56eq1008Kbps
36	r18x64eq1152Kbps
37	r19x56eq1064Kbps
38	r19x64eq1216Kbps
39	r20x56eq1120Kbps
40	r20x64eq1280Kbps
41	r21x56eq1176Kbps
42	r21x64eq1344Kbps
43	r22x56eq1232Kbps
44	r22x64eq1408Kbps
45	r23x56eq1288Kbps
46	r23x64eq1472Kbps
47	r24x56eq1344Kbps
48	r24x64eq1536Kbps
49	r25x56eq1400Kbps
50	r25x64eq1600Kbps
51	r26x56eq1456Kbps
52	r26x64eq1664Kbps
53	r27x56eq1512Kbps
54	r27x64eq1728Kbps
55	r28x56eq1568Kbps
56	r28x64eq1792Kbps
57	r29x56eq1624Kbps
58	r29x64eq1856Kbps
59	r30x56eq1680Kbps
60	r30x64eq1920Kbps
61	r31x56eq1736Kbps
62	r31x64eq1984Kbps
63	r32x56eq1792Kbps
64	r32x64eq2048Kbps
65	r1x1dot5eq1dot5M
66	r2x1dot5eq3M
67	r3x1dot5eq4dot5M
68	r4x1dot5eq6M
69	r5x1dot5eq7dot5M
70	r6x1dot5eq9M
71	r7x1dot5eq10dot5M
72	r8x1dot5eq12M
73	r1x2Meq2M
74	r2x2Meq4M
75	r3x2Meq6M
76	r4x2Meq8M
77	r5x2Meq10M
78	r6x2Meq12M
79	r7x2Meq14M
80	r8x2Meq16M
100	noRate

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.12

prtExPh1MlClkMode

Defines the clock operation mode of the T1/E1 interface.
Ports that are connected to the TDM Buses must be in
nodalTiming(3) clock mode.

Enumerationr/w

Enumerated Values:

1	fr
2	frPlus
3	pCellRelay
4	hdlcSdlc
5	transparentHdlc
6	ciscoBridgedEth

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.13

prtExPh1MlMfClkSrcSlt

This attribute indicates whether the port Tx multiframe is
synchronized with Rx multiframe of another port and the slot
position of that port.
This operation is required in order to bypass signaling of
PCM voice channel…

Enumerationr/w

Enumerated Values:

1	sameNetManaged
2	sameNetNotMana
3	user
4	otherNet
5	pubNet
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.14

prtExPh1MlMfClkSrcPrt

A unique number to identify a port position in the mux. It
has no effect when the prtExPh1MlMfClkSrcSlt selected is Local.
inPrt1 - for MTML-H/E1 cards.

Enumerationr/w

Enumerated Values:

2	no
3	flowControl

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.15

prtExPh1MlFdlType

A unique number to identify the side of the FDL operation.
Normal: 'response' for the user side and 'command' for the PTT
side.
Applicable only when working with ESF-T1 link

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.16

prtExPh1MlInbandMng

A unique number to identify an Inband management over the
link.

Enumerationr/w

Enumerated Values:

1	tc1sec
2	tc2sec
3	tc3sec
4	tc4sec
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.17

prtExPh1MlInbandMngRate

A unique number to identify the rate of the Inband
management (Kbps).
E1 port - it is not applicable when prtExPh1MlInbandMng
selected is off.
T1 port - it is not applicable when prtExPh1MlInbandMng
…

Enumerationr/w

Enumerated Values:

2	none
3	fecnBecn

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.18

prtExPh1MlRedundType

This object determines the ML redundancy type:
none - no ML redundacy
dualCableAIS - each ML card is connected by a separate
dualCableParallelTx cable to the other MUX (two cables
connect …

Enumerationr/w

Enumerated Values:

1	notApplicable
2	s36Byte
3	s150Byte
4	s264Byte
5	s378Byte
6	s492Byte
7	s236Byte
8	s472Byte
9	s708Byte
10	s944Byte
11	s1180Byte

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.19

prtExPh1MlRedundSlot

This object indicates the slot containing the redundacy ML
card, coupled with the current ML (prtExPh1MlSltIdx).
When prtExPh1MlRedundType=none (no ML redundancy) this
object will be 'notApplicable'.
In the ?004 Unit th…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	none
3	lmi
4	ansiT1
5	annexA

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.20

prtExPh1MlRedundPort

This object indicates the redundacy ML port, coupled with the
current ML port (prtExPh1MlPrtIdx).
When prtExPh1MlRedundType=none (no ML redundancy) this
object will be 'notApplicable'.
When value is not 'none', it shoul…

Enumerationr/w

Constraints:
range: 0-30

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.21

prtExPh1MlRedundRecTime

Redundancy Recovery Time (sec). After switching the ML card
to the current (prtExPh1MlSltIdx), the next ML switch can
be performed only after a minimum time, indicated by
this object.

Integer32r/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.22

prtExPh1MlInbandMngRoutProt

This attribute indicates the Inband Mng routing protocol of
the port.

Enumerationr/w

Constraints:
range: 0-10

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.23

prtExPh1MlIfType

Interface type of the port.
For T1 - csu, dsu are the valid values
For E1 - dsu, ltu are the valid values.

Enumerationr/w

Constraints:
range: 0-10

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.24

prtExPh1MlMultiplier

The data rate of each TS. The multiplier values
can be 56 kbps or 64 kbps.

Enumerationr/w

Constraints:
range: 0-1800

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.25

prtExPh1MlSupportedTS

Number of Supported Time Slots by the agent.
For Vmux-110 there is HW that supports less than 31/24
Time Slots for the E1/T1 port.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
3	channelB1
4	channelB2
5	chB1andchB2
255	none

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.26

prtExPh1MlImpedance

The Line Impedance.
For T1 (always balanced), impedance is 100 ohm.
For E1:
- balanced = 120 ohm
- unbalanced = 75 ohm.

Enumerationr/w

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.27

prtExPh1MlQ50BwControl

This object enables configuration of Q.50 Bandwidth Control on the port.
If the bandwidth exceeds a certain threshold it is possible to disable
new calls in the PBX via Q.50 protocol.

Q.50 supports only E…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	nrz
3	nrzI
4	fm0
5	manchester
6	diffManchester

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.28

prtExPh1MlQ50SignalPair

Q.50 Signaling bits Pair that is currently in use:
A&B bits or C&D bits. For Annex B it will always be: aAndB (2).

Enumerationr/w

Constraints:
range: 0-16

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.29

prtExPh1MlInternalSwitch

This parameter shows whether the data will be transferred from one port to
the other port within the same group of 2 ports.
The default value is: Enable.
Disable value might be necessary for security implementat…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	crc16
3	crc32

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.30

prtExPh1MlSigService

Signaling Service given by this link.
notApplicable - for T1 links
normal - usual Signaling
advanced - V5 Signaling.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	idles
3	flags

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.31

prtExPh1MlFragmentSize

This parameter indicates the maximum number of bytes permitted in a packet send over the Link.
Exceeding this size will cause packet fragmentation.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.2.1.1.32

prtExPh1MlTsTable

table

.1.3.6.1.4.1.164.3.2.3.2.2.2 · 1 row entry · 17 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExPh1MlTsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExPh1MlTsTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry, except prtExPh1MlTsTest that will be written
directly to the Active Configuration.

prtExPh1MlTsEntry row .1.3.6.1.4.1.164.3.2.3.2.2.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtExPh1MlTsCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.2.2.1.1

prtExPh1MlTsSltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io16) are not valid.
For the Vmux2100 Main Board notApplicable (255) is used.

Enumeration

Enumerated Values:

101	inPrt1
102	inPrt2
103	inPrt3

.1.3.6.1.4.1.164.3.2.3.2.2.2.1.2

prtExPh1MlTsPrtIdx

This attribute indicates a unique port number.
MPH.1/E1 and MPH.1/T1 cards have only one external interface.
exPrt2 - for ME1-2, MT1-2 and mhsPri cards.
exPrt3, exPrt4 - for mhsPri cards.
inPrt1 - for MTML-H/E1…

Enumeration

Constraints:
range: 1-991

.1.3.6.1.4.1.164.3.2.3.2.2.2.1.3

prtExPh1MlTsIdx

This attribute indicates a unique time slot position.
The valid time slots are 1..24 for T1 Card and
1..31 for E1 interface. In G732S-E1 lines time slot 16 is not
valid for data, it is dedicated for multiframe synchron…

SNMPv2-SMIInteger32

Enumerated Values:

2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.2.2.1.4

prtExPh1MlTsIConSlot

Enumerationr/w

Enumerated Values:

2	noConnect
3	cl
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.2.2.1.5

prtExPh1MlTsIConPrt

This attribute indicates the internally (In Mux)
connected/routed port.
For MP, the values will be:
{
exPrt1 (1) ,
exPrt2 (2) ,
exPrt3 (3) ,
exPrt4 (4) ,
exPrt5 (…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6
7	exPrt7
8	exPrt8
9	exPrt9
10	exPrt10
99	clNMS
100	noConnect
101	inPrt1
102	inPrt2
103	inPrt3
104	inPrt4
105	inPrt5
106	inPrt6
107	inPrt7
108	inPrt8
109	inPrt9
110	inPrt10
111	inPrt11
112	inPrt12

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.2.2.1.6

prtExPh1MlTsIConTs

SNMPv2-SMIInteger32r/w

Constraints:
range: 1-991

.1.3.6.1.4.1.164.3.2.3.2.2.2.1.7

prtExPh1MlTsExt

A pointer to an extension of this table:
prtExTsSplitTable.
- If prtExPh1MlTsIConSlot='split', its value
should be set to the OBJECT IDENTIFIER of the
prtExTsSplitTable, with its relevant CnfgIdx,
SltIdx, PrtIdx, …

ObjectIdentifier

Enumerated Values:

1	full
2	zero
3	txBc9600bps
4	txBc14200bps
5	txBc19200bps
6	txBc28800bps
7	txBc32000bps
8	txBc38400bps
9	txBc48000bps
10	txBc56000bps
11	txBc57600bps
12	txBc64Kbps
13	txBc128Kbps
14	txBc192Kbps
15	txBc256Kbps
16	txBc320Kbps
17	txBc384Kbps
18	txBc448Kbps
19	txBc512Kbps
20	txBc768Kbps
21	txBc1024Kbps

.1.3.6.1.4.1.164.3.2.3.2.2.2.1.8

prtExPh1MlTsTest

This attribute indicates a test to be activated on the selected TS.
It is applicable only when prtSTstCmd=testPerTS(31).
notApplicable - when prtSTstCmd is NOT testPerTS(31).
none - no test is applied for the selected …

Enumerationr/w

Enumerated Values:

1	full
2	zero
3	txBe9600bps
4	txBe14200bps
5	txBe19200bps
6	txBe28800bps
7	txBe32000bps
8	txBe38400bps
9	txBe48000bps
10	txBe56000bps
11	txBe57600bps
12	txBe64Kbps
13	txBe128Kbps
14	txBe192Kbps
15	txBe256Kbps
16	txBe320Kbps
17	txBe384Kbps
18	txBe448Kbps
19	txBe512Kbps
20	txBe768Kbps
21	txBe1024Kbps

.1.3.6.1.4.1.164.3.2.3.2.2.2.1.9

prtExPh1MlTsType

The Time Slot Type.

Transparent - means that the Time Slot will be Rx/Tx as is without processing it.

If the device requires more than 1 unique data or ss7 Time Slot,
options with numbers c…

Enumerationr/w

Enumerated Values:

1	full
2	zero
3	rxBc9600bps
4	rxBc14200bps
5	rxBc19200bps
6	rxBc28800bps
7	rxBc32000bps
8	rxBc38400bps
9	rxBc48000bps
10	rxBc56000bps
11	rxBc57600bps
12	rxBc64Kbps
13	rxBc128Kbps
14	rxBc192Kbps
15	rxBc256Kbps
16	rxBc320Kbps
17	rxBc384Kbps
18	rxBc448Kbps
19	rxBc512Kbps
20	rxBc768Kbps
21	rxBc1024Kbps

.1.3.6.1.4.1.164.3.2.3.2.2.2.1.10

prtExPh1MlTsBundle

The number of the bundle containing this Time Slot.
If no bundle exists for this TS or the bundle number
is irrelevant, the value will be 0.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	full
2	zero
3	rxBe9600bps
4	rxBe14200bps
5	rxBe19200bps
6	rxBe28800bps
7	rxBe32000bps
8	rxBe38400bps
9	rxBe48000bps
10	rxBe56000bps
11	rxBe57600bps
12	rxBe64Kbps
13	rxBe128Kbps
14	rxBe192Kbps
15	rxBe256Kbps
16	rxBe320Kbps
17	rxBe384Kbps
18	rxBe448Kbps
19	rxBe512Kbps
20	rxBe768Kbps
21	rxBe1024Kbps

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.2.2.1.11

prtExPh1MlTsTestDuration

This attribute indicates the maximum duration of executing
a test on the specific TS. This entry applies to all the
test operations.

For the Vmux2100 the values are:
0 - 60 seconds.

A zero…

SNMPv2-SMIInteger32r/w

Constraints:
range: 1-8

.1.3.6.1.4.1.164.3.2.3.2.2.2.1.12

prtExPh1MlTsSubChType

The Time Slot Sub-Channel Type.
This variable is relevant only when Time-Slot Type is SubCh
(e.g. prtExPh1MlTsType = subCh1...subCh8).

Enumerationr/w

Enumerated Values:

1	disconnected
2	connected

.1.3.6.1.4.1.164.3.2.3.2.2.2.1.13

prtExPh1MlTsSubChMask

The Sub-Channel Type Mask.
This variable is relevant only when Time-Slot Type is SubCh
(e.g. prtExPh1MlTsType = subCh1...subCh8).

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.2.2.1.14

prtExPh1MlTsChRate

The Rate of the Signaling Channel.
notApplicable(1) when TS Type is other than Signaling or Transparent

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.2.2.1.15

prtExPh1MlTsByteReversal

Byte Reversal.
This variable defines whether the LSB or MSB is transmitted first.
no(2) - MSB is transmitted first
yes(3) - LSB is transmitted first.

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.2.2.1.16

prtExPh1MlTsSigProfile

This object indicates the Signaling Profile of the port.
It is applicable only when prtMl4SigProfile=perTS.
p1 = profile 1
p2 = profile 2
p3 = profile 3
p4 = profile 4
p5 = profile 5

Enumerationr/w

Enumerated Values:

1	notApplicable
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.2.2.1.17

prtInPh1MlCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.2.3 · 1 row entry · 24 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtInPh1MlCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtInPh1MlCnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtInPh1MlCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.2.3.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtInPh1MlCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

Enumerated Values:

2	r1x64eq64Kbps
4	r2x64eq128Kbps
6	r3x64eq192Kbps
8	r4x64eq256Kbps
10	r5x64eq320Kbps
12	r6x64eq384Kbps
14	r7x64eq448Kbps
16	r8x64eq512Kbps
18	r9x64eq576Kbps
20	r10x64eq640Kbps
22	r11x64eq704Kbps
24	r12x64eq768Kbps
26	r13x64eq832Kbps
28	r14x64eq896Kbps
30	r15x64eq960Kbps
32	r16x64eq1024Kbps
34	r17x64eq1088Kbps
36	r18x64eq1152Kbps
38	r19x64eq1216Kbps
40	r20x64eq1280Kbps
42	r21x64eq1344Kbps
44	r22x64eq1408Kbps
46	r23x64eq1472Kbps
48	r24x64eq1536Kbps
50	r25x64eq1600Kbps
52	r26x64eq1664Kbps
54	r27x64eq1728Kbps
56	r28x64eq1792Kbps
58	r29x64eq1856Kbps
60	r30x64eq1920Kbps
62	r31x64eq1984Kbps
64	r32x64eq2048Kbps
70	auto

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.1

prtInPh1MlSltType

This attribute indicates a unique slot position where
the card is inserted.
For ISDN BRI port of MX300/30:
io1(5) = isdn1(5) and io2(6) = isdn2(6)
In the ?004 Unit the entries io6(10)..io12(16) are not valid

Enumeration

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.2

prtInPh1MlPrtIdx

This attribute indicates a unique port number.
MPH.1/E1 and MPH.1/T1 cards have three internal interfaces.
MX3000 modules may have up to 50 internal ports.

SNMPv2-SMIInteger32

Enumerated Values:

2	dce
3	ext-dce
4	dte

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.3

prtInPh1MlConnect

This attribute indicates whether the port should be
considered in any of the mux algorithms.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.4

prtInPh1MlRate

This attribute indicates the port speed.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	no
3	callIn
4	callOut

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.5

prtInPh1MlProtocol

This attribute indicates the applied protocol.

Enumerationr/w

Constraints:
range: 0-10

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.6

prtInPh1MlConnectionTyp

This attribute indicates the link connection type.
It is required for three reasons:
FR/CR Inband management operation (LMI,CLMM...).
CIR check.
NMS network management.

SameNetManaged - indicates network …

Enumerationr/w

Enumerated Values:

1	none
2	busA
3	busB

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.7

prtInPh1MlCongResponse

This attribute indicates how to handle the congestion indication
to/from the mux internal connection side (for example
transmit/receive becn to/from the network).
no - do nothing
FlowControl - translate t…

Enumerationr/w

Enumerated Values:

2	none
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.8

prtInPh1MlCongLevel

This attribute indicates the level of delayed data in
precents of the total available dynamic memory,
for which the port will start to operate .
The resolution of the parameter is 5 percent.
Valid values: 10..70, 25…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	txClock
3	rxClock

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.9

prtInPh1MlTc

This attribute indicates the Tc parameter which is the time
period of the sliding window in which the Bc/Be are tested.
The value of this parameter is identical for all the ports in the
specific card.
255=notApplicable.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.10

prtInPh1MlFlowControl

This attribute indicates the required flow control betweeen
the port and the remote equipment.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	random
3	bursty

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.11

prtInPh1MlSegment

This object is the Segmentation in Bytes.
In protocol FR+, ISDN internals, MX 30/300 the segmentation is:

50 (2) ,158 (3) ,266 (4) ,376 (5), 484 (6)

In MX 3000/4:
For protocol FR+ (interna…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	ignore
3	implement

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.12

prtInPh1MlFrMngProt

This object indicates the Frame-Relay management protocol.
ansiT1 = ANSI T1.617 Annex D (this is the default value).
This parameter is applicable only for FR and FR+ protocols.
When prtInPh1MlConnectionTyp = sameNetMana…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	v35
3	x21
4	rs232
5	rs449
6	ei530
7	ei530a

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.13

prtInPh1MlEnqPeriod

This object is the Status Enquiry Period, in seconds.
It determines the frequency of the Status Enquiry message
as sent by the FR user side.
At the FR network side, it determines the timeout for this
message reception.
…

Integer32r/w

Enumerated Values:

1	notApplicable
2	normal
3	inverted

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.14

prtInPh1MlFullRptPeriod

This object is the Full Report Frequency.
It determines the number of the Status Enquiry messages
sent by the FR user side, before a Full Report Request is
sent.
The units are : Status Enquiry messages (periods).
Valid …

Integer32r/w

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.15

prtInPh1MlFrWindowSize

This object is the FR Window Size.
It determines the number of samplings in the sliding window
that counts the errors.
This parameter is applicable only for FR and FR+ protocols
AND
only when prtInPh1MlFrMngProt is NOT …

Integer32r/w

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.16

prtInPh1MlErrorsThreshold

This object is the Max Errors.
It determines the number of Status Enquiry Errors that
occured within the FR sliding window, before this port is
considered DOWN (threshold).
This parameter is applicable only for FR and F…

Integer32r/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.17

prtInPh1MlMaxIdleTime

Move to higher prioritized connected link after this period of
seconds of silence on the current link.
0=Never. Never move to higher prioritized connected link.
UNIT is seconds.
Valid values are: 0, 1, 2, 3, 4, 5, 10…

Integer32r/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.18

prtInPh1MlBearerCh

Defines which B (bearer) channels are used for transferring ISDN data.
Default value is: none (255).
anyChannel (2) is skipped because it is not in use here.

Enumerationr/w

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.19

prtInPh1MlAssociatedExCh

This object indicates the external port associated to this internal
port. At present, it is used by the Hybrid (mp2100h), MHS-4 cards which
can have up to 64 dynamic internal ports associated with External ports.
…

Enumerationr/w

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.20

prtInPh1MlClockEncoding

This object is the Encoding type of the Line.
This parameter is applicable only for FR and FR+ protocols.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	r32KbpsNLE
3	r48KbpsNLE
4	r56KbpsNLE
5	r64KbpsNLE
6	r112KbpsNLE
7	r128KbpsNLE
8	r168KbpsNLE
9	r192KbpsNLE
10	r224KbpsNLE
11	r256KbpsNLE
12	r280KbpsE
13	r320KbpsE
14	r336KbpsNLE
15	r384KbpsNLE
16	r392KbpsE
17	r448KbpsNLE
18	r504KbpsLE
19	r512KbpsE
20	r560KbpsE
21	r576KbpsLE
22	r616KbpsE
23	r640KbpsE
24	r672KbpsNLE
25	r704KbpsE
26	r728KbpsE
27	r768KbpsNLE
28	r784KbpsE
29	r832KbpsE
30	r840KbpsE
31	r896KbpsNLE
32	r952KbpsE
33	r960KbpsE
34	r1008KbpsLE
35	r1024KbpsE
36	r1064KbpsE
37	r1088KbpsE
38	r1120KbpsE
39	r1152KbpsLE
40	r1176KbpsE
41	r1216KbpsE
42	r1232KbpsE
43	r1280KbpsE
44	r1288KbpsE
45	r1344KbpsNLE
46	r1400KbpsE
47	r1408KbpsE
48	r1456KbpsE
49	r1472KbpsE
50	r1512KbpsE
51	r1536KbpsE
52	r1568KbpsE
53	r1600KbpsE
54	r1624KbpsE
55	r1664KbpsE
56	r1680KbpsE
57	r1728KbpsE
58	r1736KbpsE
59	r1792KbpsNLE
60	r1856KbpsE
61	r1920KbpsE
62	r1984KbpsE
63	r2048KbpsE
65	r9d6KbpsNLE
66	r14d4KbpsNLE
67	r16KbpsNLE
68	r19d2KbpsNLE
69	r28d8KbpsNLE
70	r38d4KbpsNLE
71	r57d6KbpsNLE
72	r115d2KbpsNLE
73	r24000bps

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.21

prtInPh1MlMinSeparators

Minimum number of bytes separating between two adjacent frames (HDLC item).
0 = notApplicable

Integer32r/w

Enumerated Values:

1	notApplicable
2	r300bpsNLE
3	r600bpsNLE
4	r800bpsNLE
5	r1200bpsNLE
6	r2400bpsNLE
7	r4800bpsNLE
8	r9600bpsNLE
9	r14400bpsLE
10	r19200bpsNLE
11	r28800bpsLE
12	r32000bpsNLE
13	r38400bpsNLE
14	r48000bpsNLE
15	r56000bpsNLE
16	r57600bpsLE
17	r64000bpsNLE
18	r112000bps
19	r115200bps
20	r16000bpsNLE
21	r100bpsNLE
22	r128000bps
23	r24000bps

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.22

prtInPh1MlCcittCrc

This object indicates how many Bits are used for CRC (HDLC item).

Enumerationr/w

Enumerated Values:

1	fr
2	frPlus
3	pCellRelay
4	hdlcSdlc
5	transparentHdlc
6	async
7	asyncReliable
8	activePPP
9	slip
10	pppAgent
11	slipAgent
12	transparent
13	sna
14	ft1Dot2

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.23

prtInPh1MlFrameSeparator

This object indicates what should be transferred on the line when there
are no frames to pass (HDLC item).
idles: mean that FF will pass on the line
flags: mean that 7E will pass on the line.

Enumerationr/w

Enumerated Values:

1	sameNetManaged
2	sameNetNotMana
3	user
4	otherNet
5	pubNet
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.2.3.1.24

prtInPh1MlDlciTable

table

.1.3.6.1.4.1.164.3.2.3.2.2.4 · 1 row entry · 14 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtInPh1MlDlciTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtInPh1MlDlciTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtInPh1MlDlciEntry row .1.3.6.1.4.1.164.3.2.3.2.2.4.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtInPh1MlDlciCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

Enumerated Values:

2	no
3	flowControl
4	toFlowControl

.1.3.6.1.4.1.164.3.2.3.2.2.4.1.1

prtInPh1MlDlciSltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io16) are not valid

Enumeration

Constraints:
range: 0-70

.1.3.6.1.4.1.164.3.2.3.2.2.4.1.2

prtInPh1MlDlciPrtIdx

This attribute indicates a unique internal port number.
MPH.1/E1 and MPH.1/T1 cards have three internal ports.

Enumeration

Enumerated Values:

1	tc1sec
2	tc2sec
3	tc3sec
4	tc4sec
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.2.4.1.3

prtInPh1MlDlciIdx

This attribute indicates a unique index for each possible
used dlci(16..991). When the protocol is not Multiplexing
protocol, then its type is 'user' and the only valid index
is 1.

Integer32

Enumerated Values:

2	none
3	fecnBecn
4	xonXoff
5	dtrCts
6	speedReduction

.1.3.6.1.4.1.164.3.2.3.2.2.4.1.4

prtInPh1MlDlciValid

This attribute indicates whether the attributes in this entry
are valid or not. The user can add/delete pvc (dlci to dlci
connection) by modifing this object

Enumerationr/w

Enumerated Values:

1	notApplicable
2	on
3	endToEnd

.1.3.6.1.4.1.164.3.2.3.2.2.4.1.5

prtInPh1MlDlciIConSlt

This attribute indicates a unique slot position In the Mux
(Agent) where the dlci is routed to.
In the ?004 Unit the entries io6(10)..io16) are not valid

Enumerationr/w

Enumerated Values:

1	notApplicable
2	off
3	on

.1.3.6.1.4.1.164.3.2.3.2.2.4.1.6

prtInPh1MlDlciIConPrt

This attribute indicates a unique port id which the dlci is
routed to.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	dataBits7Bits
3	dataBits8Bits

.1.3.6.1.4.1.164.3.2.3.2.2.4.1.7

prtInPh1MlDlciIConDlci

This attribute indicates a unique internal connection dlci
number which the src dlci is routed to.

Integer32r/w

Enumerated Values:

1	notApplicable
2	odd
3	even
4	none

.1.3.6.1.4.1.164.3.2.3.2.2.4.1.8

prtInPh1MlDlciTxBc

This attribute indicates a unique Tx committed bandwidth on
the user transmit line or at the port receive line.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	sb1Bit
3	sb1dot5Bits
4	sb2Bits

.1.3.6.1.4.1.164.3.2.3.2.2.4.1.9

prtInPh1MlDlciTxBe

This attribute indicates a unique Tx excess bandwidth on the
user transmit line or at the port receive line.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.2.4.1.10

prtInPh1MlDlciRxBc

This attribute indicates a unique Rx committed bandwidth on
the user receive line or at the port transmit line.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.2.4.1.11

prtInPh1MlDlciRxBe

This attribute indicates a unique Rx excess bandwidth on the
user receive line or at the port transmit line.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	none
3	lmi
4	ansiT1
5	annexA

.1.3.6.1.4.1.164.3.2.3.2.2.4.1.12

prtInPh1MlDlciPriority

This attribute indicates a unique priority of the pcv.
1 is the lowest priority and 8 is the highest priority.

Integer32r/w

Constraints:
range: 1-30

.1.3.6.1.4.1.164.3.2.3.2.2.4.1.13

prtInPh1MlDlciStatus

This attribute indicates the status of the pvc. The status is
disconnected(1) when one of the sides is programmed as
not connected

Enumeration

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.2.4.1.14

prtPhMlCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.2.5 · 1 row entry · 18 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtPhMlCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtPhMlCnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtPhMlCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.2.5.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtPhMlCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.2.5.1.1

prtPhMlSltIdx

This attribute indicates a unique slot position where
the module is inserted.
In the ?004 Unit the entries io6(10)..io12(16) are not valid.

For the Vmux2100 Main Board notApplicable (1) is used.

Enumeration

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.2.5.1.2

prtPhMlPrtIdx

This attribute indicates a unique port number.
ML-20 cards have just one external interface.

Enumeration

Enumerated Values:

1	notApplicable
2	s36Byte
3	s150Byte
4	s264Byte
5	s378Byte
6	s492Byte

.1.3.6.1.4.1.164.3.2.3.2.2.5.1.3

prtPhMlConnect

This attribute indicates whether the port should be considered
in any of the mux algorithms.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	nrz
3	nrzI
4	fm0
5	manchester
6	diffManchester
7	nrzISpace
8	nrzIMark

.1.3.6.1.4.1.164.3.2.3.2.2.5.1.4

prtPhMlRate

This attribute indicates the configured port speed.
auto - rate is adapted automatically to the attached modem rate.

Enumerationr/w

Constraints:
range: 0-16

.1.3.6.1.4.1.164.3.2.3.2.2.5.1.5

prtPhMlCAS

This attribute indicates whether Channel Associated
Signaling (CAS) is used.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	crc16
3	crc32

.1.3.6.1.4.1.164.3.2.3.2.2.5.1.6

prtPhMlClockMode

Clock mode.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	idles
3	flags

.1.3.6.1.4.1.164.3.2.3.2.2.5.1.7

prtPhMlSatBuffer

Satellite Buffer (+/- 256).

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.2.5.1.8

prtPhMlDialProcess

Dial Process.

Enumerationr/w

Constraints:
range: 0-1000

.1.3.6.1.4.1.164.3.2.3.2.2.5.1.9

prtPhMlSyncRestore

Sync Restoration time, in seconds.
notApplicable=0.

Integer32r/w

.1.3.6.1.4.1.164.3.2.3.2.2.5.1.10

prtPhMlBus

The TDM BUS this port is linked to.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.2.5.1.11

prtPhMlMfSyncSlot

This attribute indicates whether the sync is synchronized
according to a certain card and the slot of this card.
This operation is required in order to bypass signaling of
PCM voice channels.
In the ?004 Unit the entrie…

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.2.5.1.12

prtPhMlClockSource

The Clock Source: TC (Tx Clock) or RC (Rx Clock) signals.

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.2.5.1.13

prtPhMlErrCorrection

This object indicates if Error Correction mechanism should be applied or not.
It will be applicable only if the interface HW includes the Error Correction
chip.

Enumerationr/w

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6

.1.3.6.1.4.1.164.3.2.3.2.2.5.1.14

prtPhMlCorrectionMode

This object is applicable only when prtPhMlErrCorrection=yes.
random - enables to correct up to 3 random errors in an 23 bit frame
built from 12 data bits and 11 appended parity bits.
bursty - interleaving 3 fr…

Enumerationr/w

Constraints:
range: 1-991

.1.3.6.1.4.1.164.3.2.3.2.2.5.1.15

prtPhMlControlSignals

This object shows whether the Port will ignore or implement the control signals
like DCD, CTS, DTR.

Enumerationr/w

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.2.5.1.16

prtPhMlInterfaceType

The SW Configurable Interface Type.

Enumerationr/w

Enumerated Values:

2	noConnect
3	cl
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.2.5.1.17

prtPhMlClockPolarity

This object indicates the clock polarity.

Enumerationr/w

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6
7	exPrt7
8	exPrt8
9	exPrt9
10	exPrt10
99	clNMS
100	noConnect
101	inPrt1
102	inPrt2
103	inPrt3
104	inPrt4
105	inPrt5
106	inPrt6
107	inPrt7
108	inPrt8
109	inPrt9
110	inPrt10

.1.3.6.1.4.1.164.3.2.3.2.2.5.1.18

prtExPhPlCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.3.1 · 1 row entry · 35 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExPhPlCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExPhPlCnfgTable'

The write operation into the Table Objects is
valid only to the TmpCnfg entry.

prtExPhPlCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.3.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtExPhPlCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

Enumerated Values:

1	full
2	zero
3	txBe9600bps
4	txBe14400bps
5	txBe19200bps
6	txBe28800bps
7	txBe32000bps
8	txBe38400bps
9	txBe48000bps
10	txBe56000bps
11	txBe57600bps
12	txBe64Kbps
13	txBe128Kbps
14	txBe192Kbps
15	txBe256Kbps
16	txBe320Kbps
17	txBe384Kbps
18	txBe448Kbps
19	txBe512Kbps
20	txBe768Kbps
21	txBe1024Kbps
25	txBc16000bps
26	txBc112Kbps

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.1

prtExPhPlSltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io12(16) are not valid

Enumeration

Enumerated Values:

1	full
2	zero
3	rxBc9600bps
4	rxBc14400bps
5	rxBc19200bps
6	rxBc28800bps
7	rxBc32000bps
8	rxBc38400bps
9	rxBc48000bps
10	rxBc56000bps
11	rxBc57600bps
12	rxBc64Kbps
13	rxBc128Kbps
14	rxBc192Kbps
15	rxBc256Kbps
16	rxBc320Kbps
17	rxBc384Kbps
18	rxBc448Kbps
19	rxBc512Kbps
20	rxBc768Kbps
21	rxBc1024Kbps
25	rxBc16000bps
26	rxBc112Kbps

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.2

prtExPhPlPrtIdx

This attribute indicates a unique port number.
In case of PH.1 card, only exPrt(1) is valid.

Enumeration

Enumerated Values:

1	full
2	zero
3	rxBe9600bps
4	rxBe14400bps
5	rxBe19200bps
6	rxBe28800bps
7	rxBe32000bps
8	rxBe38400bps
9	rxBe48000bps
10	rxBe56000bps
11	rxBe57600bps
12	rxBe64Kbps
13	rxBe128Kbps
14	rxBe192Kbps
15	rxBe256Kbps
16	rxBe320Kbps
17	rxBe384Kbps
18	rxBe448Kbps
19	rxBe512Kbps
20	rxBe768Kbps
21	rxBe1024Kbps
25	rxBc16000bps
26	rxBc112Kbps

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.3

prtExPhPlConnect

This attribute indicates whether the port should be considered
in any of the mux algorithms.

Enumerationr/w

Constraints:
range: 1-8

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.4

prtExPhPlHRate

This attribute indicates the port speed for HIGH speed cards.
The card has limitations about the maximum sigma channel
speeds and about the possible rates for each clock mode .
N - The rate is valid for DCE and EXT-DCE …

Enumerationr/w

Enumerated Values:

1	disconnected
2	connected

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.5

prtExPhPlLRate

This attribute indicates the port speed for LOW speed cards.
The card has limitations about the possible rates for each
clock mode.
N - The rate is valid for DCE and EXT-DCE Nodal clock mode.
L - The rate is valid for D…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.6

prtExPhPlProtocol

This object indicates the applied protocol.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.7

prtExPhPlConnectionTyp

This attribute indicates the link connection type.
It is required for three reasons:
FR/CR Inband management opration (LMI,CLMM...).
CIR check.
NMS network management.

SameNetManaged - indicates network i…

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.8

prtExPhPlClkMode

Clock mode.

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.9

prtExPhPlDceClkSrc

This attribute indicates the source of the clock when working
in dce or ext-dce clock mode.
notApplicable(1) - is applied for dte(3) and lbt(5) clock modes.
When clock mode is dte, the clock sourc…

Enumerationr/w

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.10

prtExPhPlCongResponse

This attribute indicates how to handle the congestion indication
to/from the mux internal connection side (for example
transmit/received becn to/from the network).
no - do nothing
flowControl - translates…

Enumerationr/w

Enumerated Values:

2	disable
3	enable
4	relay

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.11

prtExPhPlCongLevel

This attribute indicates the level of delayed data in
precents of total available dynamic memory,
for which the port will start to operate as congested.
The resolution of the parameter is 5 percent.

Integer32r/w

Enumerated Values:

2	onFirstFrame
3	always
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.12

prtExPhPlTc

This attribute indicates the Tc parameter which is the time
period of the sliding window in which the Bc/Be are tested.
The value of this parameter is identical for all the ports
of a specific card .

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.13

prtExPhPlFlowControl

This attribute indicates the required flow control betweeen
the port and the remote equipment.
fecnBecn - is valid only for FR, FR+ and CR protocols.
xonXoff,dtrCts - are valid only for Async protocols.
speedReduction -…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.14

prtExPhPlDcdRts

Protocol may require end to end connect indication over the
network. End to end link connection establishment over the
FR network will be indicated to the user by using DCD or
RTS control signals, depending on the clock…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.15

prtExPhPlDcdRtsControlPath

Protocol may require end to end connect indication over the
network. This parameter defines whether to take the user
connection status (RTS(DCE)/DCD(DTE)) and forward it to the
network side.
- on : Transmit active conne…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.16

prtExPhPlDataBits

This attribute indicates the number of data bits in async
frame.
It is relevant only for Async protocols.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.17

prtExPhPlParity

This attribute indicates the parity operation mode in
async frame.
It is relevant only for Async protocols.

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.18

prtExPhPlStopBits

This attribute indicates the minimum number of stop bits
in the tx async frame.
It is relevant only for Async protocols.

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.19

prtExPhPlLXon

This attribute indicates the character used as X-On to
notify receive enable.
This parameter is valid only for async protocols.
Valid values: 0..255.
The value 256 indicates that it's not applicable

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6
7	exPrt7
8	exPrt8
9	exPrt9
10	exPrt10

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.20

prtExPhPlLXoff

This attribute indicates the character used as X-Off to
notify receive disable.
This parameter is valid only for async protocols.
Valid values: 0..255.
The value 256 indicates that it's not applicable

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.21

prtExPhPlFrMngProt

Enumerationr/w

Enumerated Values:

2	r2400bps
3	r4800bps
4	r9600bps
5	r19200bps

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.22

prtExPhPlEnqPeriod

Integer32r/w

Enumerated Values:

1	dce
2	ext-dce
3	dte

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.23

prtExPhPlFullRptPeriod

Integer32r/w

Enumerated Values:

2	on
3	rts-min
4	rts-max

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.24

prtExPhPlFrWindowSize

Integer32r/w

Enumerated Values:

2	on
3	card-sync

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.25

prtExPhPlErrorsThreshold

Integer32r/w

Constraints:
range: 0-24

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.26

prtExPhPlPvcCreateMsg

This object is Update Message (if required or not).
It determines whether a message of a New PVC Creation is
requested or not (yes/no).
Default = no.
This parameter is applicable only for FR and FR+ protocols
AND
only w…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.27

prtExPhPlCllmMsg

This object is CLLM Message (if required or not).
It determines whether to send (or not) a congestion message
when the port is Rx congested.
Default = no.
This parameter is applicable only for FR and FR+ protocols
AND
o…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.28

prtExPhPlProtDelayLevel

This object is the Segmentation in Bytes.
In some cases, the enumerated values will mean
other segmentation values than specified:

Product: MX-3000 MX-3000 MX-300/MX-30
Protocol: …

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.29

prtExPhPlClockEncoding

This object is the Encoding type of the Line.
This parameter is applicable only for FR and FR+ protocols.
For MAXCESS 3000 & MP2100H: when setting to nrzI (3) the nrzI works
as nrzI Mark.
For MAXCESS 30/300 when setting…

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.30

prtExPhPlMinSeparators

Minimum number of bytes separating between two adjacent frames (HDLC item).
0 = notApplicable

Integer32r/w

Enumerated Values:

101	inPrt1
102	inPrt2

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.31

prtExPhPlCcittCrc

This object indicates how many Bits are used for CRC (HDLC item).

Enumerationr/w

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.32

prtExPhPlFrameSeparator

This object indicates what should be transferred on the line when there
are no frames to pass (HDLC item).
idles: mean that FF will pass on the line
flags: mean that 7E will pass on the line.

Enumerationr/w

Constraints:
range: 1-12

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.33

prtExPhPlIdleCode

Determines the code for transmission when there are no frames to transmit
on the line. The value should be 0 to FFH.

SNMPv2-SMIInteger32r/w

Constraints:
range: 1-4

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.34

prtExPhPlJitter

Maximum variant delay of the FR network, in msec.

Integer32r/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.3.1.1.35

prtExPhPlDlciTable

table

.1.3.6.1.4.1.164.3.2.3.2.3.2 · 1 row entry · 14 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExPhPlDlciTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExPhPlDlciTable'

The write operation into the Table Objects is valid only
at the TmpCnfg entry.

prtExPhPlDlciEntry row .1.3.6.1.4.1.164.3.2.3.2.3.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtExPhPlDlciCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

.1.3.6.1.4.1.164.3.2.3.2.3.2.1.1

prtExPhPlDlciSltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io16) are not valid

Enumeration

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.3.2.1.2

prtExPhPlDlciPrtIdx

This attribute indicates a unique internal port number.
PH.1/E1 and PH.1/T1 cards have three internal ports.
Stand-alone units may have six such ports.

Enumeration

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.3.2.1.3

prtExPhPlDlciIdx

This attribute indicates a unique index for each possible
used dlci(16..991). When the protocol is not Multiplexing
protocol, its type is 'user' and the only valid index is 1.

Integer32

.1.3.6.1.4.1.164.3.2.3.2.3.2.1.4

prtExPhPlDlciValid

This attribute indicates whether the attributes in this
entry are valid or not. The user can add/delete pvc (dlci
to dlci connection) by modifing this object

Enumerationr/w

Enumerated Values:

2	no
3	yes
4	v51
5	v52

.1.3.6.1.4.1.164.3.2.3.2.3.2.1.5

prtExPhPlDlciIConSlt

This attribute indicates a unique slot position In the Mux
(Agent) where the dlci is routed to.
cl - will represent any of the CL slots. This value can be
selected for multiple DLCIs of the product.
In the ?004 Unit t…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.3.2.1.6

prtExPhPlDlciIConPrt

This attribute indicates a unique port id which the dlci is
routed to.
clNMS - will be used for NMS SNMP messages. It can be any
port of the CL card.
This value will be selectable only if
prtExPh…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.3.2.1.7

prtExPhPlDlciIConDlci

This attribute indicates a unique internal connection dlci
number, the dlci is routed to.

Integer32r/w

Enumerated Values:

1	w2wire
2	w4wire
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.3.2.1.8

prtExPhPlDlciTxBc

This attribute indicates a unique Tx committed bandwidth on
the user transmit line (or at the port receive line).

Enumerationr/w

Enumerated Values:

1	aLAW
2	uLAW

.1.3.6.1.4.1.164.3.2.3.2.3.2.1.9

prtExPhPlDlciTxBe

This attribute indicates a unique Tx excess bandwidth on the
user transmit line (or at the port receive line).

Enumerationr/w

Enumerated Values:

1	noSignaling
2	robbedBitMultiFrame
3	chAssociatedE1
4	robbedBitFrame

.1.3.6.1.4.1.164.3.2.3.2.3.2.1.10

prtExPhPlDlciRxBc

This attribute indicates a unique Rx committed bandwidth on the
user receive line (or at the port transmit line).

Enumerationr/w

Enumerated Values:

1	forcedIdle
2	forcedBusy
3	busyIdle
4	idleBusy
5	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.3.2.1.11

prtExPhPlDlciRxBe

This attribute indicates a unique Rx excess bandwidth on the
user receive line (or at the port transmit line).

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.3.2.1.12

prtExPhPlDlciPriority

This attribute indicates a unique priority of the pcv.
1 is the lowest priority and 8 is the highest priority.

Integer32r/w

Enumerated Values:

2	normal
3	unidirectRx
4	broadcast

.1.3.6.1.4.1.164.3.2.3.2.3.2.1.13

prtExPhPlDlciStatus

This attribute indicates the status of the pvc. The status is
disconnected(1) when one of the sides is programmed as not
connected

Enumeration

Enumerated Values:

1	notApplicable
2	manual
3	p1
4	p2
5	p3Fxo3S3
6	reversePolarity
7	meteringPulse
8	p4

.1.3.6.1.4.1.164.3.2.3.2.3.2.1.14

prtExPhPlModemTable

table

.1.3.6.1.4.1.164.3.2.3.2.3.3 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExPhPlModemTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExPhPlModemTable'

External Modem Parameters.
The write operation into the
Table Objects is valid only for the TmpCnfg entry.

prtExPhPlModemEntry row .1.3.6.1.4.1.164.3.2.3.2.3.3.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtExPhPlModemCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

Enumerated Values:

1	notApplicable
2	r2Q422
3	specialA
4	specialB
5	specialC
6	specialD
7	specialE
8	specialF
9	specialG

.1.3.6.1.4.1.164.3.2.3.2.3.3.1.1

prtExPhPlModemSltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io12(16) are not valid

Enumeration

Enumerated Values:

1	notApplicable
2	off
3	on

.1.3.6.1.4.1.164.3.2.3.2.3.3.1.2

prtExPhPlModemPrtIdx

This attribute indicates a unique port number.
In case of PH.1 card, only exPrt(1) is valid.

Enumeration

Enumerated Values:

1	notApplicable
2	w2Em
3	w4Em
4	fxo
5	fxs

.1.3.6.1.4.1.164.3.2.3.2.3.3.1.3

prtExPhPlModemStatus

This object indicates whether a Dial Up Modem is enabled on this port.
Default: disable

For Vmux devices this object shows whether there is Modem Relay support.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	pcm
3	adpcm
4	linear

.1.3.6.1.4.1.164.3.2.3.2.3.3.1.4

prtExPhPlModemActivate

This object indicates whether the Dial Up Modem is activated when
the first frame is received or it is always activated.
Default: onFirstFrame

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.3.3.1.5

prtExPhPlModemMaxIdleTime

Max Time allowed in Seconds without any traffic before the line
is disconnected.

Legal Values are: 1 sec, 2 sec .. 5 sec, 10 sec, 20 sec..
1 min, 2 min .. 10 min, 15 min, 20 min, 25 min, 30 min.
65535 sec…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.3.3.1.6

prtExPhPlModemTimeBtwnCalls

Minimum Time in Seconds which is required after a call was
disconnected. In this time no other call will be initiated
from this Modem port even if there were frames transmitted
to this port. This time is required for so…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	r16Khz
3	r12Khz
4	disabled

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.3.3.1.7

prtExPhPlModemCallDelay

Time in Seconds that the device will wait before dialing to the remote
device.

This feature is mostly used when there is a backup modem to the
main link and the main link is down. In this case it is impo…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	loopStart
3	groundStart
4	winkStart

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.3.3.1.8

prtExLs2CnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.4.1 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExLs2CnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExLs2CnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtExLs2CnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.4.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtExLs2CnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg

Integer32

Enumerated Values:

1	notApplicable
2	lb
3	pbx
4	e1
5	t1
6	t1D4

.1.3.6.1.4.1.164.3.2.3.2.4.1.1.1

prtExLs2SltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io16) are not valid.

Enumeration

Enumerated Values:

1	notApplicable
2	m2
3	m3
4	m5
5	unlimited

.1.3.6.1.4.1.164.3.2.3.2.4.1.1.2

prtExLs2PrtIdx

This attribute indicates a unique port index.
For the Ls2/X.58 exPrt(7)..exPrt(10) are not valid.

Enumeration

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.4.1.1.3

prtExLs2Connect

This attribute indicates whether the port should be
considered in any of the mux algorithms.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	notExist
3	exist

.1.3.6.1.4.1.164.3.2.3.2.4.1.1.4

prtExLs2Rate

Port rates.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disabled
3	enabled

.1.3.6.1.4.1.164.3.2.3.2.4.1.1.5

prtExLs2ClkMode

This attribute indicates a unique port operation clock mode.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	f20Hz
3	f25Hz
4	f50Hz

.1.3.6.1.4.1.164.3.2.3.2.4.1.1.6

prtExLs2Cts

CTS.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	normal
3	advanced

.1.3.6.1.4.1.164.3.2.3.2.4.1.1.7

prtExLs2Dcd

DCD.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disabled
3	enabled

.1.3.6.1.4.1.164.3.2.3.2.4.1.1.8

prtExLs2EnvIdx

Envelope Index.
When prtInLs2EnvAssign=auto, the value is 0 (not applicable).

Integer32r/w

Enumerated Values:

1	notApplicable
2	g726
3	g727

.1.3.6.1.4.1.164.3.2.3.2.4.1.1.9

prtInLs2CnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.4.2 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtInLs2CnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtInLs2CnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtInLs2CnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.4.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtInLs2CnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg

Integer32

Enumerated Values:

1	notApplicable
2	low
3	medium
4	high

.1.3.6.1.4.1.164.3.2.3.2.4.2.1.1

prtInLs2SltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io16) are not valid.

Enumeration

Enumerated Values:

1	notApplicable
2	detector
3	generator

.1.3.6.1.4.1.164.3.2.3.2.4.2.1.2

prtInLs2PrtIdx

This attribute indicates a unique internal port index.

Enumeration

Enumerated Values:

1	notApplicable
2	no
3	first
4	last

.1.3.6.1.4.1.164.3.2.3.2.4.2.1.3

prtInLs2Connect

This attribute indicates whether the port should be considered in
any of the mux algorithms. It also affects all the module
considerations because the module has only one Internal
interface which is the composite chann…

Enumerationr/w

Enumerated Values:

1	g712
2	q552ETSI
3	q522Italy

.1.3.6.1.4.1.164.3.2.3.2.4.2.1.4

prtInLs2Group

This attribute indicates the group number of the port.
LS-2 internal ports with the same group number share the same Time slot of the main
link

Integer32r/w

.1.3.6.1.4.1.164.3.2.3.2.4.2.1.5

prtInLs2Member

This attribute indicates the group member id of the port.
This parameter is for the automatic envelope assignment
algorithm.

Integer32r/w

.1.3.6.1.4.1.164.3.2.3.2.4.2.1.6

prtInLs2LinkTodeprecated

It indicates the slot of the main link card to which the
LS2 card is mapped.
STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot
and prtGenCnfgLinkToPort.

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.4.2.1.7

prtInLs2EnvAssign

Envelope assignment type.

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.4.2.1.8

prtVc2CnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.5 · 1 row entry · 40 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtVc2CnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtVc2CnfgTable'

- For products supporting more than one configuration, the write operation 
into the Table is valid only to the TmpCnfg entry.
- For products that do not support configurations, the write operation 
into the Table will be to prtVc2CnfgIdx=1.

prtVc2CnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.5.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtVc2CnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg

Integer32

Enumerated Values:

1	r1x56eq56Kbps
2	r1x64eq64Kbps
3	r2x56eq112Kbps
4	r2x64eq128Kbps
5	r3x56eq168Kbps
6	r3x64eq192Kbps
7	r4x56eq224Kbps
8	r4x64eq256Kbps
9	r5x56eq280Kbps
10	r5x64eq320Kbps
11	r6x56eq336Kbps
12	r6x64eq384Kbps
13	r7x56eq392Kbps
14	r7x64eq448Kbps
15	r8x56eq448Kbps
16	r8x64eq512Kbps
17	r9x56eq504Kbps
18	r9x64eq576Kbps
19	r10x56eq560Kbps
20	r10x64eq640Kbps
21	r11x56eq616Kbps
22	r11x64eq704Kbps
23	r12x56eq672Kbps
24	r12x64eq768Kbps
25	r13x56eq728Kbps
26	r13x64eq832Kbps
27	r14x56eq784Kbps
28	r14x64eq896Kbps
29	r15x56eq840Kbps
30	r15x64eq960Kbps
31	r16x56eq896Kbps
32	r16x64eq1024Kbps
33	r17x56eq952Kbps
34	r17x64eq1088Kbps
35	r18x56eq1008Kbps
36	r18x64eq1152Kbps
37	r19x56eq1064Kbps
38	r19x64eq1216Kbps
39	r20x56eq1120Kbps
40	r20x64eq1280Kbps
41	r21x56eq1176Kbps
42	r21x64eq1344Kbps
43	r22x56eq1232Kbps
44	r22x64eq1408Kbps
45	r23x56eq1288Kbps
46	r23x64eq1472Kbps
47	r24x56eq1344Kbps
48	r24x64eq1536Kbps
49	r25x56eq1400Kbps
50	r25x64eq1600Kbps
51	r26x56eq1456Kbps
52	r26x64eq1664Kbps
53	r27x56eq1512Kbps
54	r27x64eq1728Kbps
55	r28x56eq1568Kbps
56	r28x64eq1792Kbps
57	r29x56eq1624Kbps
58	r29x64eq1856Kbps
59	r30x56eq1680Kbps
60	r30x64eq1920Kbps
61	r31x56eq1736Kbps
62	r31x64eq1984Kbps
63	r32Kbps

.1.3.6.1.4.1.164.3.2.3.2.5.1.1

prtVc2SltIdx

This attribute indicates a unique slot position where
the card is inserted.
For Stand Alone products like WR: notApplicable (255)

Enumeration

Enumerated Values:

1	dce
2	ext-dce
3	dte
4	none

.1.3.6.1.4.1.164.3.2.3.2.5.1.2

prtVc2PrtIdx

A unique identifier of the port, within the card.
For MP-2100/2200 card ports, Web Ranger and FCD-IP Voice ports
the values will be:
exPrt1 (1)
exPrt2 (2)
exPrt3 (3)
exPrt4 (4)
exPrt5 (5)
exPrt6…

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	on
3	rts

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.5.1.3

prtExVc2Connect

This attribute indicates whether the port should be
considered in any of the mux algorithms.

Enumerationr/w

Enumerated Values:

2	auto
3	s16bits
4	s30bits
5	s52bits
6	s72bits

.1.3.6.1.4.1.164.3.2.3.2.5.1.4

prtExVc2TransGain

Transmit gain in dBm.
For ports of MP-104/204, MP-2100/2200 VC-6A, VC-6AG, VC-8
VC-4/Omni and VC-16 cards, the units will be 0.1dBm because
valid values can be in 0.5dBm steps.

SNMPv2-SMIInteger32r/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.5.1.5

prtExVc2ReceiveGain

Receive gain in dBm.
For ports of MP-104/204, MP-2100/2200 VC-6A, VC-6AG, VC-8
VC-4/Omni and VC-16 cards, the units will be 0.1dBm because
valid values can be in 0.5dBm steps.

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	normal
3	unidirectRx
4	broadcast
5	bidirBcastRing

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.5.1.6

prtExVc2Wire

For some cards, this object is equal for all the ports in the specific
card because of HW limitations.
For FXO & FXS this parameter is not applicable.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disabled
3	ft1Enabled

.1.3.6.1.4.1.164.3.2.3.2.5.1.7

prtExVc2CodingLaw

This attribute indicates the Method/Law for decoding/encoding the voice
information.
aLaw(1) is the standard Law for E1 links.
uLaw(2) is the standard Law for T1 links.

This object is equal for all the po…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	normal
3	invert

.1.3.6.1.4.1.164.3.2.3.2.5.1.8

prtExVc2Sig

This attribute indicates the method for decoding/encoding the signaling
information(on/off hook).
noSignaling (1) - not using signaling (only voice).
robbedBitMultiFrame(2) - is the standard method for T1 links a…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	local
3	endToEnd

.1.3.6.1.4.1.164.3.2.3.2.5.1.9

prtExVc2Oos

This object is equal for all the ports in the specific card
because of HW limitations

Enumerationr/w

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6
7	exPrt7
8	exPrt8
9	exPrt9
10	exPrt10
11	exPrt11
12	exPrt12
100	none
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.5.1.10

prtExVc2LinkTodeprecated

This attribute indicates the slot of the ML card to which
the VC card is mapped.
STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot
and prtGenCnfgLinkToPort.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.5.1.11

prtExVc2OperMode

This object indicates the operation mode of the port.
normal = bi-directional (Tx/Rx)
unidirectRx = unidirectional Rx.
broadcast = Tx upon request.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.5.1.12

prtExVc2SigProfile

This object indicates the Signaling Profile of the port.
notApplicable - for VC-2 family and when
prtExVc2Sig=noSignaling(1)
p1 = profile 1
p2 = profile 2
p3 = profile 3
p4 = profile 4

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.5.1.13

prtExVc2CallEnable

This object indicates the Enabled Call direction.
notApplicable - for all cards except VC-2/R2.
both - incoming + outgoing.

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.5.1.14

prtExVc2R2Delay

This object indicates the R2 Delay.
notApplicable - for all cards except VC-2/R2.

Enumerationr/w

Enumerated Values:

exPrt1

.1.3.6.1.4.1.164.3.2.3.2.5.1.15

prtExVc2CasStd

This object indicates the CAS (Channel Associated Signaling)
Standard.
notApplicable - for all cards except VC-2/R2.

Enumerationr/w

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.5.1.16

prtExVc2EchoCanceler

Echo canceler activation.
notApplicable - for VC-2 and VC-6 cards.

Enumerationr/w

Enumerated Values:

2	esfT1
3	sfT1
4	g732nE1
5	g732nE1CRC
6	g732sE1
7	g732sE1CRC

.1.3.6.1.4.1.164.3.2.3.2.5.1.17

prtExVc2IfType

Interface Type.

Enumerationr/w

Enumerated Values:

1	b7T1
2	b8zsT1
4	hdb3E1

.1.3.6.1.4.1.164.3.2.3.2.5.1.18

prtExVc2Encoding

Voice Encoding Mode.
linear - is relevant only for the ports of VC-16A card.

Enumerationr/w

Enumerated Values:

1	unknown
2	len0p133ft
3	len134p266ft
4	len267p399ft
5	len400p533ft
6	len534p655ft
7	fcc68

.1.3.6.1.4.1.164.3.2.3.2.5.1.19

prtExVc2TxBitCode

- - - For MP & FCD - - -

This object represents 4 parameters, by 2 Octets :
Tx D Bit Code-MSB nibble,
Tx C Bit Code- nibble,
Tx B Bit Code- nibble,
Tx A Bit Code-LSB nibble.

Each nibb…

OctetStringr/w

Enumerated Values:

2	restoreT1secFast
3	restoreT10sec62411
4	ccittE1

.1.3.6.1.4.1.164.3.2.3.2.5.1.20

prtExVc2RxBitOutput

- - - For MP (VC-Q card only) & FCD - - -
This object represents 3 parameters by 2 Octets:
Spare -MSB nibble, always=0 hex
E Lead Output - nibble,
Reverse Polarity Output- nibble,
Metering Pulse Ou…

OctetStringr/w

Enumerated Values:

2	notsupported
3	forcedIdle
4	forcedBusy
5	busyIdle
6	idleBusy

.1.3.6.1.4.1.164.3.2.3.2.5.1.21

prtExVc2MeterRate

This entry is applicable only for VC-6A/FXO, VC-6A/FXS, VC-8/FXO,
VC-8/FXS, VC-16/FXO and VC-16/FXS.
Meter Rate means rate of Call Meter in Public Phones, in KHz units.
For some cards, the value must be the same for all…

Enumerationr/w

Enumerated Values:

2	notsupported
3	oosCode00H
4	oosCode1aH
5	oosCode54H
6	oosCode7eH
7	oosCode7fH
8	oosCode98H
9	oosCode9eH
10	oosCoded5H
11	oosCodee4H
12	oosCodeffH

.1.3.6.1.4.1.164.3.2.3.2.5.1.22

prtExVc2IfSignaling

This entry is applicable only for VC-6A, VC-6AG, VC-8/FXO, VC-8/FXS,
VC-16/FXO and VC-16/FXS cards.
Interface Analog Signaling.
Must be the same for all card's ports.
loopStart - for the usual trunk/phone types.
groundS…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.5.1.23

prtExVc2SeizeAck

This parameter shows whether the device will acknowledge
a seize signal (On/Off Hook).
When the value is set to yes(3) & the device receives an on/off hook signal
it will transmit back an on/off hook signal.
When th…

Enumerationr/w

Enumerated Values:

2	local
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.5.1.24

prtExVc2EandMType

This is the signaling type on the E&M analog side.
The analog signaling includes voltage, no. of pins and other parameters.

Enumerationr/w

Enumerated Values:

1	exPrt1
2	exPrt2
101	inPrt1

.1.3.6.1.4.1.164.3.2.3.2.5.1.25

prtExVc2RemType

Remote Type.
Applicable for VC-6A/4LB card &
for IPMUX-1E Far End Type - E1,T1(T1-ESF) or T1-D4 .

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.5.1.26

prtExVc2ConvTime

Conversation Time in minutes.
Applicable for VC-6A/4LB card.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.5.1.27

prtExVc2SigFeedback

Signaling Feedback.
Applicable for VC-8/FXO and VC-16/FXO cards.

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.5.1.28

prtExVc2EchoCancelerModule

This parameter indicates whether Echo canceler module exists for this port.

Enumeration

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.5.1.29

prtExVc2ReversePolarity

This object Enables/Disables Reverse Polarity for this port.

Enumerationr/w

Enumerated Values:

exPrt1

.1.3.6.1.4.1.164.3.2.3.2.5.1.30

prtExVc2RingerFrequency

This object selects the Ringer Frequency (Hz) for this port.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.5.1.31

prtExVc2SigService

Signaling Service.
advanced - is relevant only for ports of VC-8, VC-16 FXS cards.
It is used for Signaling Services of V5.1 or R2.

Enumerationr/w

Enumerated Values:

2	noConnect
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
100	split

.1.3.6.1.4.1.164.3.2.3.2.5.1.32

prtExVc2CallerIdEnable

This object Enables/Disables Receiving the Caller Id number from the
remote side, for this port/channel.

Enumerationr/w

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6
7	exPrt7
8	exPrt8
9	exPrt9
10	exPrt10
11	exPrt11
12	exPrt12
100	noConnect

.1.3.6.1.4.1.164.3.2.3.2.5.1.33

prtExVc2CompressMethod

This object is applicable only when prtExVc2Encoding=adpcm.
It defines which method is used for Compression.
g726 - for 4 bits (the standard method).
g726 - for 3 bits. It is especially needed for T1 applications with s…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.5.1.34

prtExVc2ObMode

This object defines the Net operation mode of the Omni-Bus card's port.
pointToPoint - only 2 end-point ports talk; like any other voice card
omniBus - many talk and listen. Like conference call.
Al…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.5.1.35

prtExVc2VAD

This object defines whether Voice Activation Detector (VAD)
will be On or Off.
off - will be usually selected when a Modem is connected
to the port; not a phone.
notApplicable - when prtExVc2DspMode=pointT…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.5.1.36

prtExVc2NoiseLevelForVAD

This object defines the Level of Noise on the line,
the Voice Activation Detector (VAD) will have to deal with.
notApplicable - when prtExVc2VAD=off.

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.5.1.37

prtExVc2WesternSigMode

This object defines the Western Signaling Mode.
detector - detects signal and passes it as is.
generator - generates the signal.
notApplicable - when Western HW is not installed.

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
17	io13
18	io14
19	io15
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.5.1.38

prtExVc2BusProtectionPoint

This object defines if the port is Bus Protection Point or not.
notApplicable - when prtExVc2DspMode=pointToPoint.
When we have a chain of devices where the edge devices ports are the
Bus Protection Point, user must co…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.5.1.39

prtExVc2ImpedanceStandard

This object defines the Standard used for Impedance.
-G.712 - 600 Ohm - used in USA and other countries.
-Q552/ETSI - used in some countries in Europe
-Q522/Italy - used in Italy.

Enumerationr/w

Enumerated Values:

2	no
3	yes
4	v51
5	v52

.1.3.6.1.4.1.164.3.2.3.2.5.1.40

prtHsfCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.6 · 1 row entry · 14 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtHsfCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtHsfCnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtHsfCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.6.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtHsfCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relate to the TmpCnfg.

Integer32

Enumerated Values:

1	lt
2	nt
3	te
4	lt1
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.6.1.1

prtHsfSltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io16) are not valid.

Enumeration

Enumerated Values:

1	notApplicable
2	type1
3	type2
4	type3

.1.3.6.1.4.1.164.3.2.3.2.6.1.2

prtHsfPrtIdx

This attribute indicates a unique external port index.
Hs2 has only two ports (exPrt1,exPrt2).
Hs3 has three ports (exPrt1,exPrt2,exPrt3).
Hsq and hsqN has four ports.
Hs6 has six external ports.
Hs12 has twelve extern…

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.6.1.3

prtExHsfConnect

This attribute indicates whether the port should be
considered in any of the mux algorithms.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.6.1.4

prtExHsfRate

This attribute indicates the port speed.

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.6.1.5

prtExHsfClkMode

This attribute indicates a unique port operation clock mode.

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
17	io13
18	io14
19	io15
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.6.1.6

prtExHsfCts

This attribute indicates a unique CTS control line
operation mode.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.6.1.7

prtExHsfFifoSize

Size in bits.

Enumerationr/w

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.6.1.8

prtExHsfLinkTodeprecated

This attribute indicates a slot of Main Link module, that the
port is linked to. This object is the same for all the
ports in the specific card because of HW limitations.
STATUS deprecated - this object is replaced by …

Enumerationr/w

Enumerated Values:

2	r600bps
3	r1200bps
4	r2400bps
5	r4800bps
6	r9600bps
7	r19200bps
8	r38400bps
9	r48kbps
10	r56kbps
11	r64kbps
12	r128kbps
13	concentrated
100	notConnected
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.6.1.9

prtExHsfOperMode

This object indicates the operation mode of the port.
normal = bi-directional (Tx/Rx)
unidirectRx = unidirectional Rx.
broadcast = Tx upon request.
bidirBcastRing = Bidirectional Broadcast Ring. When this value is selec…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.6.1.10

prtExHsfInbandLoopback

This object indicates if Inband Loopback from the Network
should be enabled or disabled.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.6.1.11

prtExHsfClkPolarity

This object indicates the clock polarity.
For FCD-M this object will be applicable only for the fixed HS port
(the fixed port on the device).

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.6.1.12

prtExHsfControlSignal

This object indicates the Control Signal according to G.797 ITU-T standard.
For FCD-M this object will be applicable for the fixed HS port
(the fixed port on the device) and HS-Q/N channels.
Local and End to End are app…

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.6.1.13

prtExHsfBcastRingSrcPort

This object is applicable only when prtExHsfOperMode=
bidirBcastRing. In this case, the values mean:
- none - this port will be connected to ML in TSA as usual.
- exPrt1.. exPrtX ; X=maximum ports of the card in focus …

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.6.1.14

prtExHs4CnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.7.1 · 1 row entry · 13 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExHs4CnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExHs4CnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtExHs4CnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.7.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtExHs4CnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg

Integer32

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.7.1.1.1

prtExHs4SltIdx

This attribute indicates a unique slot position where
the card is inserted.

Enumeration

Enumerated Values:

1	unknown
2	eAndM4wires
3	eAndM2wires
4	fxoGnd
5	fxoLoop
6	fxsGnd
7	fxsLoop
8	e1Framer
9	e1Slave
10	t1Framer
11	t1Slave

.1.3.6.1.4.1.164.3.2.3.2.7.1.1.2

prtExHs4PrtIdx

A unique identifier of the port, within the card.

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.7.1.1.3

prtExHs4Connect

This attribute indicates whether the port should be
considered in any of the mux algorithm. It also affects
all the module considerations because the card has only
one external (physical) interface.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.7.1.1.4

prtExHs4LineType

This attribute is the line type parameter for T1/E1
interface.
The user should select only the parameters relevant to the
specific card:
T1 line code parameters for the HS-4/1 and
E1 line code parameters for the HS-4/2.…

Enumerationr/w

Enumerated Values:

1	notConnected
2	r4800bps
3	r7200bps
4	r9600bps
255	notApplicatble

.1.3.6.1.4.1.164.3.2.3.2.7.1.1.5

prtExHs4LineCode

This attribute is the line code parameter used for T1/E1
interface.
The user should select only the parameters relevant to the
specific card:
T1 line code parameters for the MPH.1/T1 and
E1 line code parameters for the …

Enumerationr/w

Enumerated Values:

1	t1sec
2	t2sec
3	t3sec
4	t4sec

.1.3.6.1.4.1.164.3.2.3.2.7.1.1.6

prtExHs4LineLen

This attribute is the line length parameter used only for
T1 interfaces.
len399p533ft=len-399-533ft

Enumerationr/w

Enumerated Values:

2	notSupported
3	forcedIdle
4	forcedBusy
5	busyIdle
6	idleBusy

.1.3.6.1.4.1.164.3.2.3.2.7.1.1.7

prtExHs4RestoreT

Time passing from the disappearance of the loss of
synchronization condition (red alarm), to the restoration
of normal service.

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.2.3.2.7.1.1.8

prtExHs4OosSig

Out of Service signal type.

Enumerationr/w

Constraints:
range: 0-300

.1.3.6.1.4.1.164.3.2.3.2.7.1.1.9

prtExHs4OosCode

OOS Code

Enumerationr/w

Constraints:
range: 0-70

.1.3.6.1.4.1.164.3.2.3.2.7.1.1.10

prtExHs4IdleCode

Type value(00 - FF HEX), excluding 0H,8H,10H,12H,21H,24H,
42H,49H,84H,92H

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	w2wire
2	w4wire
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.7.1.1.11

prtExHs4MfClkSrcSlt

This attribute indicates whether the port Tx is multiframe
synchronized with Rx multiframe of another port and the slot position of that port.
This opration is required in order to bypass signaling of PCM
voice channels…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	forceConnect
3	voiceSwitching
4	transparent
5	transparentPlus
6	ipForceConnect
7	permanentDial
8	autoAccept

.1.3.6.1.4.1.164.3.2.3.2.7.1.1.12

prtExHs4MfClkSrcPrt

A unique number to identify a port position in the mux if the
MultiFrame clock source is valid (YES).
inPrt1 - for MTML-H/E1 cards.

Enumerationr/w

Constraints:
range: 2-2

.1.3.6.1.4.1.164.3.2.3.2.7.1.1.13

prtExHs4TsCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.7.2 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExHs4TsCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExHs4TsCnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtExHs4TsEntry row .1.3.6.1.4.1.164.3.2.3.2.7.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtExHs4TsCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

Constraints:
range: 0-10

.1.3.6.1.4.1.164.3.2.3.2.7.2.1.1

prtExHs4TsSltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io16) are not valid

Enumeration

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.7.2.1.2

prtExHs4TsPrtIdx

This attribute indicates a unique port number.
Hs4/T1 and Hs4/T1 cards have only one external interface.

Enumeration

Enumerated Values:

1	notConnected
2	r4800bps
3	r7200bps
4	r9600bps
5	r12000bps
6	r14400bps
7	r2400bps
8	vbdFax

.1.3.6.1.4.1.164.3.2.3.2.7.2.1.3

prtExHs4TsIdx

SNMPv2-SMIInteger32

Enumerated Values:

2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.7.2.1.4

prtExHs4TsIConSlot

Enumerationr/w

Enumerated Values:

2	delayStart
3	immediateStart
4	winkStart

.1.3.6.1.4.1.164.3.2.3.2.7.2.1.5

prtExHs4TsIConPrt

This attribute indicates the internally (In Mux)
connected/routed port.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.7.2.1.6

prtExHs4TsIConTs

This attribute indicates a unique time slot position.
The valid time slots are:
1..24 for T1 Module and
1..31 for E1 interface.
In G732S-E1 lines time slot 16 is not valid for data,
it is dedicated for multiframe synch…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.7.2.1.7

prtExHsiCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.8.1 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExHsiCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExHsiCnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtExHsiCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.8.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtExHsiCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg

Integer32

Enumerated Values:

1	aLAW
2	uLAW

.1.3.6.1.4.1.164.3.2.3.2.8.1.1.1

prtExHsiSltIdx

This attribute indicates a unique slot position where
the card is inserted.

Enumeration

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.8.1.1.2

prtExHsiPrtIdx

A unique port identifier within the card.
For MP : 1..12
For DXC: 111 .. 2531. See DXC R6 spec for port index convention.
For FCD-A, 'S' Interface external ports: 131, 141, 151, 161.

SNMPv2-SMIInteger32

Constraints:
range: 0-256

.1.3.6.1.4.1.164.3.2.3.2.8.1.1.3

prtExHsiConnect

This attribute indicates whether the port should be considered in
any of the mux algorithms.
v51 - this port is connected to a V5.1 interface. All rest of the
values will be 'notApplicable' in this case. V5 MIB w…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	line
3	trunk

.1.3.6.1.4.1.164.3.2.3.2.8.1.1.4

prtExHsiRate

This attribute indicates the port speed.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	g7231r6300BPS
3	g7231r5300BPS
4	g729A8KBPS
5	g711aLAW
6	g711uLAW
7	g726r16KBPS
8	g726r24KBPS
9	g726r32KBPS
10	g726r40KBPS
11	g727r16KBPS
12	g727r24r16KBPS
13	g727r24KBPS
14	g727r16r32KBPS
15	g727r32r24KBPS
16	g727r32KBPS
17	g727r40r16KBPS
18	g727r40r24KBPS
19	g727r40r32KBPS
20	transparent
21	netcoder6400BPS
22	netcoder7200BPS
23	netcoder8KBPS
24	netcoder8800BPS
25	netcoder9600BPS
26	lowBitRateR2660BPS
27	amr4750BPS
28	amr5150BPS
29	amr5900BPS
30	amr6700BPS
31	amr7400BPS
32	amr7950BPS
33	amr10200BPS
34	amr12200BPS

.1.3.6.1.4.1.164.3.2.3.2.8.1.1.5

prtExHsiLinkTodeprecated

It indicates the slot of the main link card to which the HS-? card
is mapped.
STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot
and prtGenCnfgLinkToPort.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.8.1.1.6

prtExHsiInterface

It indicates the interface type:
lt = line termination
nt = network termination
te = terminal equipment.
lt1 - for ASMi-31 connection (not ISDN)
For MP:
For HS-U/I only 'lt' and 'nt' are applicable.
For HS-U…

Enumerationr/w

Enumerated Values:

2	disable
3	enable

.1.3.6.1.4.1.164.3.2.3.2.8.1.1.7

prtExHsiActType

It indicates the Activation Type. Activation Type is the Synchronization
type towards the PBX. It is applicable only when prtExHsiInterface=nt.
notApplicable - for cards that do not support this object, or when
prtExHs…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.8.1.1.8

prtInHsiCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.8.2 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtInHsiCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtInHsiCnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.
This table is not applicable for MP-2100 HS-U card type.

prtInHsiCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.8.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtInHsiCnfgIdx

This object indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg

Integer32

Constraints:
range: 0-31

.1.3.6.1.4.1.164.3.2.3.2.8.2.1.1

prtInHsiSltIdx

This object indicates a unique slot position where
the card is inserted.

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.8.2.1.2

prtInHsiPrtIdx

A unique port identifier within the card.
Valid values for MP: inPrt1 (101) .. inPrt48 (148).
Valid values for DXC: 11012.. 25316. See DXC R6 spec for port index convention.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.8.2.1.3

prtInHsiConnect

This attribute indicates whether the port should be considered in
any of the mux algorithms.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	ptp
3	aal2oMpls

.1.3.6.1.4.1.164.3.2.3.2.8.2.1.4

prtInHsiRate

This object indicates the port speed.
For HS-U/I and HS-S ports:
2 bit - up to 9600bps
4 bit - 19200bps
8 bit - 38400bps .. 64kbps.
concentrated - this D channel goes to a Concentration channel,
that repr…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.2.3.2.8.2.1.5

prtInHsiConcentratedTo

The Concentration D Channel of the prtInHsiPrtIdx port.
The port always belongs to the same card as prtInHsiPrtIdx port.
This object is applicable only when prtInHsiRate=concentrated.
Valid values:
- notApplicable: 255
…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.8.2.1.6

prtExPVc4CnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.9.1 · 1 row entry · 52 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExPVc4CnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExPVc4CnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtExPVc4CnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.9.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtExPVc4CnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg

Integer32

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.1

prtExPVc4SltIdx

This attribute indicates a unique slot position where
the card is inserted.

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.2

prtExPVc4PrtIdx

This object indicates the port number in the selected card
(slot).

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.3

prtExPVc4PrtType

This object indicates the type of the selected port.
In Mx 30/300 phase 4: s0 & u are for Voice over ISDN.
In MX 30/300 phase 5: sQsig & uQsig are used for Voice over ISDN with Qsig option.

In MX MVC4…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.4

prtExPVc4Connect

This attribute indicates whether the port should be
considered in any of the mux algorithms.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.5

prtExPVc4IfType

This attribute indicates the interface type of the port.
eAndM4wires and eAndM2wires - are valid only for E&M
port type
eAndM4wires - means 2/4 wires
fxoGnd and fxoLoop - are valid onl…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.6

prtExPVc4TxGain

Transmission gain in dB.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.7

prtExPVc4RxGain

Reception gain in dBm.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.8

prtExPVc4MaxRate

Voice rate.

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.9

prtExPVc4Tc

Time interval for CIR control, in seconds. The value will
be the same for all cards' ports.

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.10

prtExPVc4Oos

Handling type, when connection is lost.

Enumerationr/w

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.11

prtExPVc4EchoCanceler

Echo canceler activation.

Enumerationr/w

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.12

prtExPVc4VarDelay

Maximum variant delay of the FR network, in msec.

Integer32r/w

Enumerated Values:

2	noConnect
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.13

prtExPVc4CongLevel

This object indicates the level of delayed data in
precents of total available dynamic memory,
for which the port will start to operate as congested.
The resolution of the parameter is 5%.

Integer32r/w

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6
7	exPrt7
8	exPrt8
9	exPrt9
10	exPrt10
100	noConnect
101	inPrt1
102	inPrt2
103	inPrt3
104	inPrt4
105	inPrt5
106	inPrt6
107	inPrt7
108	inPrt8
109	inPrt9
110	inPrt10
111	inPrt11
112	inPrt12

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.14

prtExPVc4Wire

This object indicates the wiring of the E&M port.
It is applicable only for E&M card type.

Enumerationr/w

Constraints:
range: 1-991

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.15

prtExPVc4ExtensionType

This object indicates the type of extension relevant for this port.

ipForceConnect (6) is used for automatic connection or automatic
dialing when the phone is off hook (hot line).
permanentDial (7) means …

Enumerationr/w

Enumerated Values:

1	full
2	zero
3	txBc9600bps
4	txBc14400bps
5	txBc19200bps
6	txBc28800bps
7	txBc32000bps
8	txBc38400bps
9	txBc48000bps
10	txBc56000bps
11	txBc57600bps
12	txBc64Kbps
13	txBc128Kbps
14	txBc192Kbps
15	txBc256Kbps
16	txBc320Kbps
17	txBc384Kbps
18	txBc448Kbps
19	txBc512Kbps
20	txBc768Kbps
21	txBc1024Kbps
25	txBc16000bps
26	txBc112Kbps

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.16

prtExPVc4ExtensionNumber

This is the extension number of this port.
This field is relevant only when the extension
type is voice switching and is read only if the
port is member of a hunt group.

OctetStringr/w

Enumerated Values:

1	full
2	zero
3	txBe9600bps
4	txBe14400bps
5	txBe19200bps
6	txBe28800bps
7	txBe32000bps
8	txBe38400bps
9	txBe48000bps
10	txBe56000bps
11	txBe57600bps
12	txBe64Kbps
13	txBe128Kbps
14	txBe192Kbps
15	txBe256Kbps
16	txBe320Kbps
17	txBe384Kbps
18	txBe448Kbps
19	txBe512Kbps
20	txBe768Kbps
21	txBe1024Kbps
25	txBc16000bps
26	txBc112Kbps

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.17

prtExPVc4OutPulsing

This field indicates whether to outpulse the received
digits. It is notApplicable(1) when the extension type
is forceConnect(2).

Enumerationr/w

Enumerated Values:

1	full
2	zero
3	rxBc9600bps
4	rxBc14400bps
5	rxBc19200bps
6	rxBc28800bps
7	rxBc32000bps
8	rxBc38400bps
9	rxBc48000bps
10	rxBc56000bps
11	rxBc57600bps
12	rxBc64Kbps
13	rxBc128Kbps
14	rxBc192Kbps
15	rxBc256Kbps
16	rxBc320Kbps
17	rxBc384Kbps
18	rxBc448Kbps
19	rxBc512Kbps
20	rxBc768Kbps
21	rxBc1024Kbps
25	rxBc16000bps
26	rxBc112Kbps

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.18

prtExPVc4HuntGroupMb

This object indicates if this port belongs to
an hunt group.

Enumerationr/w

Enumerated Values:

1	full
2	zero
3	rxBe9600bps
4	rxBe14400bps
5	rxBe19200bps
6	rxBe28800bps
7	rxBe32000bps
8	rxBe38400bps
9	rxBe48000bps
10	rxBe56000bps
11	rxBe57600bps
12	rxBe64Kbps
13	rxBe128Kbps
14	rxBe192Kbps
15	rxBe256Kbps
16	rxBe320Kbps
17	rxBe384Kbps
18	rxBe448Kbps
19	rxBe512Kbps
20	rxBe768Kbps
21	rxBe1024Kbps
25	rxBc16000bps
26	rxBc112Kbps

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.19

prtExPVc4HuntGroupIdx

If it belongs to an hunt group, this fields
indicates the index of the relevant hunt group.
0 = notApplicable

Integer32r/w

Constraints:
range: 6-8

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.20

prtExPVc4AutoFaxMode

This object indicates if the system will switch automatically to
FAX mode when detecting FAX activity.
Default=Yes.

Enumerationr/w

Enumerated Values:

1	disconnected
2	connected

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.21

prtExPVc4FaxRate

FAX initial rate.
Default=9600 bps.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.22

prtExPVc4SeizeAck

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.23

prtExPVc4SignalingProtocol

The signaling protocol that will be used between the PABX & the voice port.

Delay Start Protocol: the line is seized by sending an Off hook signal
and after a delay, if the called party is available (On h…

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.24

prtExPVc4DelayStart

This parameter is used only for Delay Protocol.
This is the time that the calling party will wait after sending an Off hook
signal and before sending DTMF digits to the called party.
The delay values are 100..5000 msec …

SNMPv2-SMIInteger32r/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
17	io13
18	io14
19	io15

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.25

prtExPVc4WinkMinDuration

This parameter is used only for Wink Protocol.
Min Duration of the Wink Signal (off hook duration from the called party).
Legal values: 40..400 msec in intervals of 10 msec.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.26

prtExPVc4WinkMaxDuration

This parameter is used only for Wink Protocol.
Max Duration of the Wink Signal (off hook duration from the called party).
Legal values: 40..400 msec in intervals of 10 msec.

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.27

prtExPVc4GenerateTone

This parameter indicates whether the device (MX or MPH) should generate
dial tones for the channel.
If the value is yes (3), it generates dial tones.
If the value is no (2), the connected equipment will generate dial t…

Enumerationr/w

Enumerated Values:

2	sync
3	async

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.28

prtExPVc4CodingLaw

Enumerationr/w

Enumerated Values:

2	r600bps
3	r1200bps
4	r2400bps
5	r4800bps
6	r9600bps
7	r19200bps
8	r38400bps
9	r48kbps
10	r56kbps
11	r64kbps
12	r16000bps
13	r32000bps
14	r57600bps
15	r115200bps
16	r128000bps
17	r7200bps
18	r14400bps
19	r28800bps
100	notConnected

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.29

prtExPVc4GenerateRingBack

Determines whether the Ring Back tone is generated locally or from the
remote end.
The default is - NO (Meaning coming from the remote end).
Yes means that the Ring Back Tone is generated locally.
Applicable onl…

Enumerationr/w

Enumerated Values:

1	d5bits
2	d6bits
3	d7bits
4	d8bits
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.30

prtExPVc4ChannelId

Channel Identifier.
According to FRF11 each voice port that works as force connect should add a
CH Id after the DLCI in the frame header.

Default : 1

Applicable only for Force Connect.
Not…

Integer32r/w

Enumerated Values:

2	no
3	yes
4	odd
5	even
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.31

prtExPVc4PortConnection

Port connection determines whether the port is connected to a PABX (Trunk) or to
Telephone set (Line) .

It determines whether to send certain messages to the port or not.
If the type is LINE then the port…

Enumerationr/w

Enumerated Values:

1	stopBits1Bit
2	stopBits2Bits
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.32

prtExPVc4CoderAndRate

Coder and Rate for the Voice Compression.
In MPH: Relevant for MVC-8 card only.

Enumerationr/w

Enumerated Values:

2	on
3	rts
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.33

prtExPVc4DestinationNum

The destination phone number: 0 to 22 digits.
Applicable for Auto Dial - ipForceConnect(6), Permanent Dial and
Auto Accept Extension Types.

Default: Null String

SNMPv2-TCDisplayStringr/w

Enumerated Values:

1	dce
2	extDce
255	notApplicable

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.34

prtExPVc4DtmfRelay

When DTMF RELAY is disabled, the DTMF digits (dialed by the user)
are transmitted as compressed voice and in the remote unit are decompressed.

When DTMF RELAY is enabled, the DTMF digits are detected at t…

Enumerationr/w

Enumerated Values:

1	notApplicable
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.35

prtExPVc4DiscOnSilence

No. of silenced seconds after which the call will be disconected.
A value of 0 means that there will be no disconnect when there is silence.
Possible values: 0 - 900 sec.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	local
3	endToEnd

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.36

prtExPVc4DynamicJitter

The MVC8 uses two mechanisms to overcome the network delay.
The first one is a static jitter buffer which holds a constant buffer of up
to 300 Msec and can be controled by the JITTER parameter (prtExPVc4VarDelay).
The s…

Enumerationr/w

Enumerated Values:

2	normal
3	unidirectRx
4	broadcast

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.37

prtExPVc4EandMType

This is the signaling type on the E&M analog side.
The analog signaling includes voltage, no. of pins and other parameters.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	local
3	endToEnd

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.38

prtExPVc4Rate

This is the Rate of the port in TS units. It is used by VF-30 card family.
0 = NA = port is not intended to be connected; therefore, no Rate.

Integer32r/w

Enumerated Values:

1	notApplicable
2	disabled
3	enabled

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.39

prtExPVc4FrameSize

Defines the maximum size in Bytes of the multiplexed frame.
In some cases this must be limited to avoid IP fragmentation,
which makes the multiplexing useless, and can also decrease
the damage in case of frame loss.
Val…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	disabled
3	enabled

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.40

prtExPVc4MultiplexInterval

Defines the maximum amout of time (msec.) between multiplexed frames
that are sent.

For Vmux-400/420 devices:
It defines the Payload Packetizing Interval.

Valid values: 10-90 msec.…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	proprietary
3	v110

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.41

prtExPVc4TransportProtocol

Transport Protocol.
ptp = point to point.
aal2oMpls = AAL2 over MPLS.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	asmi31
3	asmi31s2

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.42

prtExPVc4MultiFreqRelay

This object enables/disables Multi Frequency Signaling Detection.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	bwOptimized
3	latencyOptimized
4	asmi31

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.43

prtExPVc4MinPulseWidth

Defines the minimum Pulse Width in msec.
Valid values: 45-100 msec.
notApplicable=0.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.44

prtExPVc4MinPowerLevel

Defines the minimum Power Level in dBm.
Valid values: -1..-35 dBm.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.45

prtExPVc4SuperTandem

The Super Tandem feature provides end to end compression
over multiple hops, solving the double compression problem
detected in Voice compressing systems.
The Super Tandem, when enabled, allows transmission of
compre…

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.46

prtExPVc4DestIp

This object defines the destination IP Address.

RFC1155-SMIIpAddressr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.47

prtExPVc4DestBundle

This object defines the destination Bundle at the
far-end device.

SNMPv2-SMIInteger32r/w

Enumerated Values:

exPrt1

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.48

prtExPVc4SrcIpAddress

This object defines the Source IP Address.

RFC1155-SMIIpAddressr/w

Enumerated Values:

1	remote
2	main

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.49

prtExPVc4SrcIpMask

This object defines the Source IP Mask.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.50

prtExPVc4DefaultGateway

This object defines the Default Gateway for this interface.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.51

prtExPVc4SigPacketInterval

Defines the Signaling Packetizing Interval,
which is the maximum time interval, measured in msec (milliseconds),
between multiplexed signaling frames.

SNMPv2-SMIUnsigned32r/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.9.1.1.52

prtExPVc4DlciTable

table

.1.3.6.1.4.1.164.3.2.3.2.9.2 · 1 row entry · 13 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExPVc4DlciTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExPVc4DlciTable'

The write operation into the Table Objects is valid only
at the TmpCnfg entry.

prtExPVc4DlciEntry row .1.3.6.1.4.1.164.3.2.3.2.9.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtExPVc4DlciCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.9.2.1.1

prtExPVc4DlciSltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io16) are not valid

Enumeration

Enumerated Values:

1	r1x64eq64Kbps
2	r2x64eq128Kbps
3	r3x64eq192Kbps
4	r4x64eq256Kbps
5	r5x64eq320Kbps
6	r6x64eq384Kbps
7	r7x64eq448Kbps
8	r8x64eq512Kbps
9	r9x64eq576Kbps
10	r10x64eq640Kbps
11	r11x64eq704Kbps
12	r12x64eq768Kbps
13	r13x64eq832Kbps
14	r14x64eq896Kbps
15	r15x64eq960Kbps
16	r16x64eq1024Kbps
17	r17x64eq1088Kbps
18	r18x64eq1152Kbps
19	r19x64eq1216Kbps
20	r20x64eq1280Kbps
21	r21x64eq1344Kbps
22	r22x64eq1408Kbps
23	r23x64eq1472Kbps
24	r24x64eq1536Kbps

.1.3.6.1.4.1.164.3.2.3.2.9.2.1.2

prtExPVc4DlciPrtIdx

This attribute indicates a unique internal port number.
VC4 cards have four external ports.

Enumeration

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.9.2.1.3

prtExPVc4DlciValid

This attribute indicates whether the attributes in this
entry are valid or not. The user can add/delete pvc (dlci
to dlci connection) by modifing this object

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.9.2.1.4

prtExPVc4DlciIConSlt

This attribute indicates a unique slot position In the Mux
(Agent) where the dlci is routed to.
In the ?004 Unit the entries io6(10)..io16) are not valid

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.9.2.1.5

prtExPVc4DlciIConPrt

This attribute indicates a unique port id which the dlci is
routed to.

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.9.2.1.6

prtExPVc4DlciIConDlci

This attribute indicates a unique internal connection dlci
number, the dlci is routed to.

Integer32r/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.9.2.1.7

prtExPVc4DlciTxBc

This attribute indicates a unique Tx committed bandwidth on
the user transmit line (or at the port receive line).

Enumerationr/w

Enumerated Values:

exPrt1

.1.3.6.1.4.1.164.3.2.3.2.9.2.1.8

prtExPVc4DlciTxBe

This attribute indicates a unique Tx excess bandwidth on the
user transmit line (or at the port receive line).

Enumerationr/w

Enumerated Values:

1	remote
2	main

.1.3.6.1.4.1.164.3.2.3.2.9.2.1.9

prtExPVc4DlciRxBc

This attribute indicates a unique Rx committed bandwidth on the
user receive line (or at the port transmit line).

Enumerationr/w

Enumerated Values:

1	r4M
2	r16M

.1.3.6.1.4.1.164.3.2.3.2.9.2.1.10

prtExPVc4DlciRxBe

This attribute indicates a unique Rx excess bandwidth on the
user receive line (or at the port transmit line).

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.9.2.1.11

prtExPVc4DlciPriority

This attribute indicates a unique priority of the pvc.
6 is the lowest priority and 8 is the highest priority.

Integer32r/w

.1.3.6.1.4.1.164.3.2.3.2.9.2.1.12

prtExPVc4DlciStatus

This attribute indicates the status of the pvc. The status is
disconnected(1) when one of the sides is programmed as not
connected

Enumeration

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.9.2.1.13

prtExHsrCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.10.1 · 1 row entry · 20 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExHsrCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExHsrCnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtExHsrCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.10.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtExHsrCnfgIdx

This object indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg

Integer32

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.10.1.1.1

prtExHsrSltIdx

This object indicates a unique slot position where
the card is inserted.

Enumeration

Enumerated Values:

1	r1x56eq56Kbps
2	r1x64eq64Kbps
3	r2x56eq112Kbps
4	r2x64eq128Kbps
5	r3x56eq168Kbps
6	r3x64eq192Kbps
7	r4x56eq224Kbps
8	r4x64eq256Kbps
9	r5x56eq280Kbps
10	r5x64eq320Kbps
11	r6x56eq336Kbps
12	r6x64eq384Kbps
13	r7x56eq392Kbps
14	r7x64eq448Kbps
15	r8x56eq448Kbps
16	r8x64eq512Kbps
17	r9x56eq504Kbps

.1.3.6.1.4.1.164.3.2.3.2.10.1.1.2

prtExHsrPrtIdx

A unique prt identifier within the card.
Valid values:
For MP:
- For HS-R cards: exPrt1 (1) .. exPrt4 (4)
- For HS-U/1 cards: inPrt1 (101) .. inPrt4 (104)
- For HS-S12, HS-S6, HS-U12, HS-U6 cards:
exPrt1 (1)…

SNMPv2-SMIInteger32

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.10.1.1.3

prtExHsrConnect

This object indicates whether the port should be considered in
any of the mux algorithms.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.10.1.1.4

prtExHsrProtocol

This object indicates the protocol.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.10.1.1.5

prtExHsrRate

This object indicates the port speed.
The 16,32,48,56,64 and 128 kbps rates are applicable only for Sync
protocol.
The 57.6 and 115.2 kbps rates are applicable only for Async
protocol.
notConnected= 0 rate.

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.10.1.1.6

prtExHsrDataBits

Data Bits.
This object is applicable for Async protocol only.

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.10.1.1.7

prtExHsrParity

- For HS-R card, this object indicates if the parity bit is needed or not.
Therefore, the 'no' and 'yes; values are applicable.
- For HS-S12, HS-U12, the parity type is selected: no, odd, even.
This object is applicabl…

Enumerationr/w

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6
7	exPrt7
8	exPrt8
9	exPrt9
10	exPrt10
11	exPrt11
12	exPrt12

.1.3.6.1.4.1.164.3.2.3.2.10.1.1.8

prtExHsrStopBits

This object indicates the minimum number of stop bits in
the tx async frame.
This object is applicable for Async protocol only.

Enumerationr/w

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.10.1.1.9

prtExHsrCts

CTS.
This object is applicable for Async protocol only.

Enumerationr/w

Enumerated Values:

2	sync
3	async

.1.3.6.1.4.1.164.3.2.3.2.10.1.1.10

prtExHsrClkMode

Clock mode.
This object is applicable for Sync protocol only.

Enumerationr/w

Enumerated Values:

2	r300bps
3	r600bps
4	r1200bps
5	r2400bps
6	r4800bps
7	r7200bps
8	r8000bps
9	r9600bps
10	r14400bps
11	r16000bps
12	r19200bps
13	r24000bps
14	r28800bps
15	r32000bps
16	r38400bps
17	r48000bps
18	r56000bps
19	r57600bps
20	r64000bps

.1.3.6.1.4.1.164.3.2.3.2.10.1.1.11

prtExHsrLinkTodeprecated

It indicates the slot of the main link card to which the HS-R card
is mapped.
notApplicable - for HS-U/1 internal ports.
STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot
and prtGenCnfgLinkToPort.

Enumerationr/w

Enumerated Values:

1	dce
2	extDce
3	dte1
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.10.1.1.12

prtExHsrDcdDsr

DCD & DSR.

Enumerationr/w

Enumerated Values:

2	local
3	rts
4	dtrAndRts

.1.3.6.1.4.1.164.3.2.3.2.10.1.1.13

prtExHsrOperMode

This object indicates the operation mode of the port.
normal = bi-directional (Tx/Rx)
unidirectRx = unidirectional Rx.
broadcast = Tx upon request.

Enumerationr/w

Enumerated Values:

1	d6bits
2	d7bits
3	d8bits
4	d9bits
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.10.1.1.14

prtExHsrRtsDtr

RTS & DTR.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	on
3	rts

.1.3.6.1.4.1.164.3.2.3.2.10.1.1.15

prtExHsrLlbEnable

Enable/Disable LLB.

Enumerationr/w

Enumerated Values:

101	inPrt1
102	inPrt2
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.10.1.1.16

prtExHsrRlbEnable

Enable/Disable RLB.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.10.1.1.17

prtExHsrRateAdapt

Rate Adaptation - takes a low rate and adapts it to 64Kbps.
This object specifies the means this adaptation is done by.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.10.1.1.18

prtExHsrRemoteModem

Remote modem.
asmi31s2 = ASMi-31/2

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.10.1.1.19

prtExHsrEncapsMode

Low Speed encapsulation method over PCM.

When Encapsulation mode is Latency optimized, only rates up to 19.2 are supported.
In this case a double number of bits occupy the Time Slot.
For up to 9.6 Kbps …

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.10.1.1.20

prtExMbeCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.11.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExMbeCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExMbeCnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtExMbeCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.11.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtExMbeCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg

Integer32

Enumerated Values:

2	r6400bps
3	r7200bps
4	r8000bps
5	r9600bps
6	r16000bps
7	r24000bps
8	r32000bps
9	r64000bps

.1.3.6.1.4.1.164.3.2.3.2.11.1.1.1

prtExMbeSltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io16) are not valid.

Enumeration

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.2.3.2.11.1.1.2

prtExMbePrtIdx

A unique port identifier within the card.

Enumeration

Enumerated Values:

1	w2wire
2	w4wire

.1.3.6.1.4.1.164.3.2.3.2.11.1.1.3

prtExMbeLan

This attribute indicates whether the MBE port is operated
as main or remote bridge.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.11.1.1.4

prtInMbeCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.11.2 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtInMbeCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtInMbeCnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtInMbeCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.11.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtInMbeCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg

Integer32

.1.3.6.1.4.1.164.3.2.3.2.11.2.1.1

prtInMbeSltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io16) are not valid.

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.11.2.1.2

prtInMbePrtIdx

A unique port identifier within the card.

Enumeration

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.11.2.1.3

prtInMbeConnect

This attribute indicates whether the port should be considered in
any of the mux algorithms.

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.11.2.1.4

prtInMbeRate

This attribute indicates the port speed.

Enumerationr/w

Enumerated Values:

101	inPrt1
102	inPrt2

.1.3.6.1.4.1.164.3.2.3.2.11.2.1.5

prtInMbeLinkTodeprecated

It indicates the slot of the main link card to which the
MBE card is mapped.
In the ?004 Unit the entries io6(10)..io16) are not valid.
STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot
and prtGenCnfg…

Enumerationr/w

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.11.2.1.6

prtExTreCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.12.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExTreCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExTreCnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtExTreCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.12.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtExTreCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg

Integer32

Enumerated Values:

1	ls6
2	km2kSlave
3	km2kStandalone
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.12.1.1.1

prtExTreSltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io16) are not valid.

Enumeration

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.12.1.1.2

prtExTrePrtIdx

A unique port identifier within the card.

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.12.1.1.3

prtExTreLan

This attribute indicates whether the TRE port is operated
as main or remote bridge.
Default=remote.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.12.1.1.4

prtExTreLanRate

This attribute indicates the Rate of the TRE port
in Mbit/sec.
Default-r4M.

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.12.1.1.5

prtInTreCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.12.2 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtInTreCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtInTreCnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtInTreCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.12.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtInTreCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg

Integer32

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.12.2.1.1

prtInTreSltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io16) are not valid.

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.12.2.1.2

prtInTrePrtIdx

A unique port identifier within the card.

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.12.2.1.3

prtInTreConnect

This attribute indicates whether the port should be considered
in any of the mux algorithms.

Enumerationr/w

Enumerated Values:

1	w2wire
2	w4wire

.1.3.6.1.4.1.164.3.2.3.2.12.2.1.4

prtInTreRate

This attribute indicates the port speed.

Enumerationr/w

Enumerated Values:

1	r9600bps
2	r4800bps

.1.3.6.1.4.1.164.3.2.3.2.12.2.1.5

prtInTreLinkTodeprecated

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.2.3.2.12.2.1.6

prtExLs6CnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.13.1 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExLs6CnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExLs6CnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtExLs6CnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.13.1.1

An entry in table.

Indexes

prtInVc3CnfgIdx prtInVc3SltIdx prtInVc3PrtIdx

Column Syntax OID

prtExLs6CnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg

Integer32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.13.1.1.1

prtExLs6SltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io12(16) are not valid.

Enumeration

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.13.1.1.2

prtExLs6PrtIdx

This attribute indicates a unique port index.

Enumeration

Enumerated Values:

101

inPrt1

.1.3.6.1.4.1.164.3.2.3.2.13.1.1.3

prtExLs6Connect

This attribute indicates whether the port should be
considered in any of the mux algorithms.

Enumerationr/w

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.13.1.1.4

prtExLs6Protocol

This attribute indicates the protocol.
async - can be selected only for ports 1-2.

Enumerationr/w

Enumerated Values:

1	r32000bps
2	r16000bps

.1.3.6.1.4.1.164.3.2.3.2.13.1.1.5

prtExLs6Rate

Port rates in bps.
g1 - contains the values : (2)-(6),(9),(12),(16)
g2 - contains the values : (7),(10),(14),(19)
g3 - contains the values : (8),(11),(13),(15),(17),(18),(20);
it is not applicable when using Async …

Enumerationr/w

Enumerated Values:

1	forcedIdle
2	forcedBusy
3	busyIdle
4	idleBusy

.1.3.6.1.4.1.164.3.2.3.2.13.1.1.6

prtExLs6ClkMode

This attribute indicates a unique port operation clock mode.
It is applicable for Sync protocol only .

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.13.1.1.7

prtExLs6CtrlSignal

Control Signal.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.13.1.1.8

prtExLs6DataBits

Data Bits.
This object is applicable for Async protocol only.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.13.1.1.9

prtExLs6Cts

This object indicates the CTS control line
operation mode.

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.13.1.1.10

prtExLs6LinkToInternal

This object indicates which internal port of the card,
the external port is linked to.

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.13.1.1.11

prtExLs6VCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.13.2 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExLs6VCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExLs6VCnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtExLs6VCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.13.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtExLs6VCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg

Integer32

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.13.2.1.1

prtExLs6VSltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io12(16) are not valid.

Enumeration

Enumerated Values:

2	no
3	yes
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.13.2.1.2

prtExLs6VPrtIdx

A unique identifier of the port, within the card.

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.13.2.1.3

prtExLs6VConnect

This attribute indicates whether the port should be
considered in any of the mux algorithms.

Enumerationr/w

Enumerated Values:

2	esfT1
3	sfT1
4	g732nE1
5	g732nE1CRC
6	g732sE1
7	g732sE1CRC
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.13.2.1.4

prtExLs6VRate

Rate (bps) used for FAX transmission and Voice coding.

Enumerationr/w

Enumerated Values:

2	restoreT1secFast
3	restoreT10sec62411
4	ccittE1
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.13.2.1.5

prtExLs6VEchoCanceler

Echo canceler activation.

Enumerationr/w

Enumerated Values:

1	b7zsT1
2	b8zsT1
3	transT1
4	hdb3E1
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.13.2.1.6

prtExLs6VIfType

This attribute indicates the interface type of the port.
w4wire - is applicable only for E&M port type.

Enumerationr/w

Enumerated Values:

1	unknown
2	len0p133ft
3	len134p266ft
4	len267p399ft
5	len400p533ft
6	len534p655ft
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.13.2.1.7

prtExLs6VTxGain

Transmit gain in dBm.
E&M - values range: -17 .. 8
FXO - values range: -16 .. 4
FXS - values range: -13 .. 8

SNMPv2-SMIInteger32r/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.13.2.1.8

prtExLs6VRxGain

Receive gain in dBm.
E&M - values range: -17 .. 2
FXO - values range: -17 .. -1
FXS - values range: -17 .. 2

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	normal
3	bEqA
4	inverseA

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.13.2.1.9

prtExLs6VOos

Out of Service signaling mode.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	hff
3	he4
4	hd5
5	h9e
6	h98
7	h7f
8	h7e
9	h54
10	h1a

.1.3.6.1.4.1.164.3.2.3.2.13.2.1.10

prtInLs6CnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.13.3 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtInLs6CnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtInLs6CnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtInLs6CnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.13.3.1

An entry in table.

Indexes

prtIn1p6VcPbxCnfgIdx prtIn1p6VcPbxSltIdx prtIn1p6VcPbxPrtIdx

Column Syntax OID

prtInLs6CnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg

Integer32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.13.3.1.1

prtInLs6SltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io12(16) are not valid.

Enumeration

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.13.3.1.2

prtInLs6PrtIdx

This attribute indicates a unique internal port index.

Enumeration

Enumerated Values:

101	inPrt1
102	inPrt2
103	inPrt3
104	inPrt4
105	inPrt5
106	inPrt6

.1.3.6.1.4.1.164.3.2.3.2.13.3.1.3

prtInLs6Connect

Enumerationr/w

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.13.3.1.4

prtInLs6TandemMode

This object indicates the Tandem Mode.
tandemSlave - is valid only for an LS-6 card having on
the (current slot-1) an LS-6 card with 'tandemMaster' mode.

Enumerationr/w

Enumerated Values:

1	r4800bps
2	r6400bps
3	r7200bps
4	r8000bps
5	r9600bps
6	r12800bps

.1.3.6.1.4.1.164.3.2.3.2.13.3.1.5

prtInLs6Rate

Main Rate in Kbps.

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.2.3.2.13.3.1.6

prtInLs6RemoteType

Remote Type.
notApplicable - when prtInLs6TandemMode=tandemSlave

Enumerationr/w

Constraints:
range: 1-31

.1.3.6.1.4.1.164.3.2.3.2.13.3.1.7

prtInLs6LinkTodeprecated

It indicates the slot of the main link card to which the
Ls6 card is mapped.
In the ?004 Unit the entries io6(10)..io12(16) are not valid.
notApplicable - when prtInLs6TandemMode=tandemSlave.
STATUS deprecated - this o…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.13.3.1.8

prtExVc3CnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.14.1 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExVc3CnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExVc3CnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtExVc3CnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.14.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtExVc3CnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg

Integer32

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.14.1.1.1

prtExVc3SltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io12(16) are not valid.

Enumeration

Enumerated Values:

107	inPrt7
108	inPrt8

.1.3.6.1.4.1.164.3.2.3.2.14.1.1.2

prtExVc3PrtIdx

A unique identifier of the port, within the card.

Enumeration

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.14.1.1.3

prtExVc3Connect

This attribute indicates whether the port should be
considered in any of the mux algorithms.

Enumerationr/w

Enumerated Values:

1	normal
2	server

.1.3.6.1.4.1.164.3.2.3.2.14.1.1.4

prtExVc3TransGain

Transmit gain in dBm.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	r32Kbps
2	r16Kbps
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.14.1.1.5

prtExVc3ReceiveGain

Receive gain in dBm.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	none
2	aBit
3	abcBit
4	abcdBit

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.14.1.1.6

prtExVc3Wire

This object is equal for all the ports in the specific
card because of HW limitations

Enumerationr/w

Enumerated Values:

1	forcedIdle
2	forcedBusy

.1.3.6.1.4.1.164.3.2.3.2.14.1.1.7

prtExVc3Rate

Rate in bps.

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.14.1.1.8

prtExVc3EchoCanceler

Echo canceler activation. The value will be the same for
all the card's external ports.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.14.1.1.9

prtInVc3CnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.14.2 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtInVc3CnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtInVc3CnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtInVc3CnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.14.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtInVc3CnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg

Integer32

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.14.2.1.1

prtInVc3SltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io12(16) are not valid.

Enumeration

Enumerated Values:

1	exPrt1
2	exPrt2
109	inPrt9
110	inPrt10

.1.3.6.1.4.1.164.3.2.3.2.14.2.1.2

prtInVc3PrtIdx

A unique identifier of the port, within the card.

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.14.2.1.3

prtInVc3Connect

This attribute indicates whether the port should be
considered in any of the mux algorithms.

Enumerationr/w

Enumerated Values:

1	unused
2	compressed
3	transparent
4	compressedCcs
5	mng
11	ccs1
12	ccs2
13	ccs3
14	ccs4
15	ccs5
16	ccs6
17	ccs7
18	ccs8
41	ss7n1
42	ss7n2
43	ss7n3
44	ss7n4
45	ss7n5
46	ss7n6
47	ss7n7
48	ss7n8

.1.3.6.1.4.1.164.3.2.3.2.14.2.1.4

prtInVc3Rate

Rate in bps.

Enumerationr/w

Enumerated Values:

2	noConnect
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.14.2.1.5

prtInVc3Oos

This object is equal for all the ports in the specific
card because of HW limitations

Enumerationr/w

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6
7	exPrt7
8	exPrt8
100	noConnect
101	inPrt1
102	inPrt2
103	inPrt3
104	inPrt4
105	inPrt5
106	inPrt6
107	inPrt7
108	inPrt8

.1.3.6.1.4.1.164.3.2.3.2.14.2.1.6

prtInVc3LinkTodeprecated

This attribute indicates the slot of the ML card to which
the VC card is mapped.
In the ?004 Unit the entries io6(10)..io12(16) are not valid.
STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot
and prt…

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.14.2.1.7

prtExVcPbxCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.15.1 · 1 row entry · 14 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExVcPbxCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExVcPbxCnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtExVcPbxCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.15.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtExVcPbxCnfgIdx

This object indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg

Integer32

.1.3.6.1.4.1.164.3.2.3.2.15.1.1.1

prtExVcPbxSltIdx

This object indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io12(16) are not valid.

Enumeration

Enumerated Values:

2	noConnect
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.15.1.1.2

prtExVcPbxPrtIdx

A unique identifier of the port, within the card.

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.15.1.1.3

prtExVcPbxConnect

This object indicates whether the port should be
considered in any of the mux algorithms.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.15.1.1.4

prtExVcPbxGroup

The group object links together several VC-PBX cards,
concerning compression of the same input T1/E1 link
time-slots.
When ports of different slots have the same group, they are
linked.
When ports have a different group…

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.15.1.1.5

prtExVcPbxTransparent

This object indicates whether the Transparent transfer
of Time-Slots is required or not.
Time-Slots transferred by Transparent, will not be
compressed.
no - applicable only for VC-PBX/T1 and VC-PBX/E1 cards
yes - appli…

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.15.1.1.6

prtExVcPbxTransSignalTs

This object specifies the ML Time-Slot dedicated to
the signaling of the PABX Transparent TSs.
None = 255.
When prtExVcPbxTransparent=no this object's value=None (255)
When prtExVcPbxTransparent=notApplicable, this obje…

SNMPv2-SMIInteger32r/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
103	kmxMlA
104	kmxMlB
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.15.1.1.7

prtExVcPbxFrame

This object is the frame parameter for T1/E1 interface.
The user should select only the parameters which are relevant
to the specific card:
T1 values for the VC-PBX/T1 card.
E1 values for the VC-PBX/E1 card.
notApplicab…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.15.1.1.8

prtExVcPbxRestoreTime

Enumerationr/w

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.15.1.1.9

prtExVcPbxLineCode

This object is the line code parameter used for T1/E1
interface.
The user should select only the parameters which are relevant
to the specific card:
T1 line code parameters for VC-PBX/T1
E1 line code parameters for VC-P…

Enumerationr/w

Enumerated Values:

1	other
3	etsi
5	ess4
6	ess5
7	dms100
9	ni1
10	ni2
17	ins64
18	ins1500
21	qsig
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.15.1.1.10

prtExVcPbxLineLength

This object is the line length parameter.
It is applicable only for the VC-PBX/T1 card.
notApplicable - for the VC-PBX and VC-PBX/E1 card.
lenXXXpXXXft = len-XXX-XXXft.

Enumerationr/w

Enumerated Values:

1	pointToPoint
2	pointToMultipoint
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.15.1.1.11

prtExVcPbxLinkTodeprecated

This object indicates the slot of the ML card to which
the VC-PBX/T1, VC-PBX/E1 card Transparent TSs are mapped.
notApplicable - for VC-PBX card AND
for VC-PBX/T1, VC-PBX/E1 cards, when prtExVcPbxTransparent=no .
In the…

Enumerationr/w

Enumerated Values:

1	dialup
2	leased
3	syncLeased
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.15.1.1.12

prtExVcPbxSignalOper

This object indicates the Signaling Operation of the
VC-PBX/T1, VC-PBX/E1 external port.
notApplicable - for VC-PBX card
normal - all 4 signaling bits are transferred.
bEqA - copy the A bit into the B bit. Applicable …

Enumerationr/w

Enumerated Values:

1	notApplicable
2	answerAll
3	rejectAll
4	selective
5	callBack

.1.3.6.1.4.1.164.3.2.3.2.15.1.1.13

prtExVcPbxIdleCode

Determines the code for transmission in empty time slots.
notApplicable - for VC-PBX card .

Enumerationr/w

Enumerated Values:

1	notApplicable
2	accept
3	reject

.1.3.6.1.4.1.164.3.2.3.2.15.1.1.14

prtIn1p6VcPbxCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.15.2 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtIn1p6VcPbxCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtIn1p6VcPbxCnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtIn1p6VcPbxCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.15.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtIn1p6VcPbxCnfgIdx

This object indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg

Integer32

Enumerated Values:

1	notApplicable
2	aSide
3	bSide

.1.3.6.1.4.1.164.3.2.3.2.15.2.1.1

prtIn1p6VcPbxSltIdx

This object indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io12(16) are not valid.

Enumeration

Enumerated Values:

1	notApplicable
2	slave
3	master

.1.3.6.1.4.1.164.3.2.3.2.15.2.1.2

prtIn1p6VcPbxPrtIdx

A unique identifier of the port, within the card.

Enumeration

Enumerated Values:

1	lt
2	nt
3	te
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.15.2.1.3

prtIn1p6VcPbxConnect

This object indicates whether the port should be
considered in any of the mux algorithms.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	initiate
3	listen

.1.3.6.1.4.1.164.3.2.3.2.15.2.1.4

prtIn1p6VcPbxRate

This object indicates the port Rate.
For Normal mode (prtIn7p8VcPbxMode=normal), only part of the values
are valid (constant rate).
For Server mode (prtIn7p8VcPbxMode=server), all values are
applicable (user can select …

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.15.2.1.5

prtIn1p6VcPbxEchoCanceler

Echo canceler activation.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.15.2.1.6

prtIn1p6VcPbxPabxTs

This object defines the PABX Time-Slot assigned to this
internal port.
For a T1 link, the valid values are: 1 .. 24.
For an E1 link, the valid values are: 1 .. 31.
This object is NOT applicable when prtIn1p6VcPbxConnec…

Integer32

.1.3.6.1.4.1.164.3.2.3.2.15.2.1.7

prtIn7p8VcPbxCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.15.3 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtIn7p8VcPbxCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtIn7p8VcPbxCnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtIn7p8VcPbxCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.15.3.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtIn7p8VcPbxCnfgIdx

This object indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg

Integer32

.1.3.6.1.4.1.164.3.2.3.2.15.3.1.1

prtIn7p8VcPbxSltIdx

This object indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io12(16) are not valid.

Enumeration

Enumerated Values:

1	atei1
2	atei2

.1.3.6.1.4.1.164.3.2.3.2.15.3.1.2

prtIn7p8VcPbxPrtIdx

A unique identifier of the port, within the card.

Enumeration

Enumerated Values:

1	dynamic
2	static
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.15.3.1.3

prtIn7p8VcPbxConnect

This object indicates whether the port should be
considered in any of the mux algorithms.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.15.3.1.4

prtIn7p8VcPbxMode

This object indicates the working mode of the port:
- normal - the compressed voice will be sent to an MTML
card inside the Mux.
- server - the compressed voice will be sent to the Digital
Voice co…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.15.3.1.5

prtIn7p8VcPbxRate

This object indicates the port Main Rate.
For Server mode (prtIn7p8VcPbxMode=server), the value will
be notApplicable.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	anyChannel
3	channelB1
4	channelB2

.1.3.6.1.4.1.164.3.2.3.2.15.3.1.6

prtIn7p8VcPbxSignalMode

This object indicates the Signal Mode.
For Server mode (prtIn7p8VcPbxMode=server), the only valid
values are:
- none
- aBit

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.15.3.1.7

prtIn7p8VcPbxOos

Out of service Signaling mode.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.15.3.1.8

prtIn7p8VcPbxLinkTodeprecated

This object indicates the slot of the ML card to which
the VC card is mapped.
In the ?004 Unit the entries io6(10)..io12(16) are not valid.
For Server mode (prtIn7p8VcPbxMode=server), this object is
not applicable.
Both…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.15.3.1.9

prtExVcPbxTsTable

table

.1.3.6.1.4.1.164.3.2.3.2.15.4 · 1 row entry · 13 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtExVcPbxTsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtExVcPbxTsTable'

The write operation into the table objects is valid only
to the TmpCnfg entry.

prtExVcPbxTsEntry row .1.3.6.1.4.1.164.3.2.3.2.15.4.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
prtExVcPbxTsCnfgIdx This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg.	Integer32	`.1.3.6.1.4.1.164.3.2.3.2.15.4.1.1`
prtExVcPbxTsSltIdx This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid	Enumeration Constraints: `range: 17-20`	`.1.3.6.1.4.1.164.3.2.3.2.15.4.1.2`
prtExVcPbxTsPrtIdx This attribute indicates a unique port number. VCPBX/E1, VCPBX/T1, VFPBX/E1, VFPBX/T1, VF-24/T1 and VF-30 cards have only one external interface. VF-48/T1 and VF-60/E1 cards have two external interfaces. VFS cards hav…	Enumeration Constraints: `range: 4-6`	`.1.3.6.1.4.1.164.3.2.3.2.15.4.1.3`
prtExVcPbxTsIdx This attribute indicates a unique PABX time slot position. The valid time slots are 1..24 for T1 cards and 1..31 for E1 cards.	SNMPv2-SMIInteger32 Constraints: `range: 17-20`	`.1.3.6.1.4.1.164.3.2.3.2.15.4.1.4`
prtExVcPbxTsMode This attribute indicates the usage, process and way of the specific PABX TS towards its destination: unused - the TS is not used (no processing, no destination). compressed - the TS is used, sent for compression to an …	Enumerationr/w Constraints: `range: 4-6`	`.1.3.6.1.4.1.164.3.2.3.2.15.4.1.5`
prtExVcPbxTsIConSlot For VF-PBX cards, the io1..io12 values are applicable only when prtExVcPbxTsMode=compressed. Otherwise, its value should be noConnect. For VF-24/30/48/60 cards: - when prtExVcPbxTsMode=transparent or voiceTransp…	Enumerationr/w	`.1.3.6.1.4.1.164.3.2.3.2.15.4.1.6`
prtExVcPbxTsIConPrt This attribute indicates the port to which this TS is connected. For VF-PBX cards, only inPrt1..inPrt6 ports are valid. For VF-24/30/48/60 cards: - for prtExVcPbxTsMode=transparent or voiceTransparent, the valid por…	Enumerationr/w	`.1.3.6.1.4.1.164.3.2.3.2.15.4.1.7`
prtExVcPbxTsIConTs This attribute indicates the ML TS to which this TS is connected. This object is not applicable for VF-PBX cards. For VF-24/30/48/60 cards it is applicable only when prtExVcPbxTsMode=transparent or voiceTransparent. Th…	Integer32r/w	`.1.3.6.1.4.1.164.3.2.3.2.15.4.1.8`
prtExVcPbxTsRemPrt This attribute indicates the end-point port on the Remote unit. VF-24/T1 and VF-30/E1 cards have one external interface. VF-48/T1 and VF-60/E1 cards have two external interfaces. noConnect - when prtExVcPbxTsMode=unused…	Enumerationr/w Constraints: `range: 17-20`	`.1.3.6.1.4.1.164.3.2.3.2.15.4.1.9`
prtExVcPbxTsRemTs This attribute indicates the end-point TS on the Remote unit. The valid time slots are 1..24 for T1 ports and 1..31 for E1 ports. notApplicable - 255.	SNMPv2-SMIInteger32r/w Constraints: `range: 4-6`	`.1.3.6.1.4.1.164.3.2.3.2.15.4.1.10`
prtExVcPbxTsRemConnID This attribute indicates the Connection ID with the Remote unit. notApplicable = 0.	SNMPv2-SMIUnsigned32r/w Constraints: `range: 17-20`	`.1.3.6.1.4.1.164.3.2.3.2.15.4.1.11`
prtExVcPbxTsSourceSlot For VFS cards. These cards offer Compresed Voice Services for Analog Voice ports of the MP. This object indicates the Source Slot of the Analog Voice port we want to compress. io1..io12 values are applicable only when…	Enumerationr/w Constraints: `range: 4-6`	`.1.3.6.1.4.1.164.3.2.3.2.15.4.1.12`
prtExVcPbxTsSourcePrt For VFS cards. These cards offer Compresed Voice Services for Analog Voice ports of the MP. This object indicates the Source Port within the Slot of the Analog Voice Card, we want to compress. exPrt1 - exPrt16 = 1 - 1…	SNMPv2-SMIUnsigned32r/w Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.2.3.2.15.4.1.13`

prtIsdnCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.16.1 · 1 row entry · 16 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtIsdnCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtIsdnCnfgTable'

The write operation into the table objects is valid only
to the TmpCnfg entry.

prtIsdnCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.16.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtIsdnCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.16.1.1.1

prtIsdnSltIdx

This attribute indicates a unique slot position where
the card is inserted.
In the ?004 Unit the entries io6(10)..io12(16) are not valid
For KM2100/4 Valid entries are 'kmxMlA ' or 'kmxMlB'

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.16.1.1.2

prtIsdnPrtIdx

This attribute indicates a unique port number.
For MAXcess the values will be:
exPrt1(1),
exPrt2(2),
exPrt3(3),
exPrt4(4),
For KM-2100 the port index is calculated as follows:
100*Slot+Ch

SNMPv2-SMIInteger32

Enumerated Values:

2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.16.1.1.3

prtIsdnConnect

This attribute indicates if the port is connected.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	linkSelector
3	encapsulator
4	huntGroup

.1.3.6.1.4.1.164.3.2.3.2.16.1.1.4

prtIsdnSignalingProtocol

This attribute fixes which signaling protocol
is used at this port (D-Channel).
It is equivalent to isdnSignalingProtocol
in the isdn MIB.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.16.1.1.5

prtIsdnBasicRateLineTopology

This attribute is relevant for ISDN BRI only.
It is equivalent to isdnBasicRateLineTopology
in the isdn MIB.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.16.1.1.6

prtIsdnMode

This attribute allows the user to configure the port as
leased(2) in case of connection to a TDM network.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.16.1.1.7

prtIsdnFilter

This attribute allows the user to configure the port:
answerAll(2): accept all incoming calls,
rejectAll(3): reject all incoming calls,
selective(4): accept or reject according directory table.
callBack (5): In this mod…

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.16.1.1.8

prtIsdnSimultaneousCall

In case of simultaneous call (local,remote and remote,local):
accept(2): accept the incoming call,
reject(3): reject the incoming call.

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.16.1.1.9

prtIsdnNumOfAbstractTerm

An object for KM2100/4 agents.
255=Not Applicable
When ISDN Standard = ETSI or NTT (European) the value should be 255 (NotApplicable)
else If ML speed is 64Kbps value should be 1.
If ML speed is 128Kbps value c…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.16.1.1.10

prtIsdnSwitchMode

For KM2100.
auto - The call is initiated automatically by one of the IO cards connected
to KML.10(ISDN card) having ISDN Switch Mode.
manual - The call is initiated by the user manually, for KML.10
…

Enumerationr/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.2.3.2.16.1.1.11

prtIsdnAbSide

This parameter indicates the QSIG side in layer 3.
This definition is from the QSIG Standard.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	backup
3	bod

.1.3.6.1.4.1.164.3.2.3.2.16.1.1.12

prtIsdnQsigRole

This parameter indicates the QSIG side in layer 1 & 2.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	auto
3	manual

.1.3.6.1.4.1.164.3.2.3.2.16.1.1.13

prtIsdnInterface

It indicates the interface type:
lt = line termination
nt = network termination
te = terminal equipment.

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.16.1.1.14

prtIsdnCallMode

This object indicates the acceptance of incoming calls.
Initiate - Callout
Listen - Callin.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.16.1.1.15

prtIsdnCallBackTimeout

This object is applicable only if 'prtIsdnFilter' is 'CallBack'
and determines how long to wait from receiving the incoming call
until initiating the call back call.
The vaules range should be '1..20 sec' and the defaul…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.16.1.1.16

prtIsdnEndpointTable

table

.1.3.6.1.4.1.164.3.2.3.2.16.2 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtIsdnEndpointTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtIsdnEndpointTable'

The write operation into the table objects is valid only
to the TmpCnfg entry.

prtIsdnEndpointEntry row .1.3.6.1.4.1.164.3.2.3.2.16.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtIsdnEndpointCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

Constraints:
range: 200-250

.1.3.6.1.4.1.164.3.2.3.2.16.2.1.1

prtIsdnEndpointSltIdx

This attribute indicates a unique slot position where
the card is inserted.
In ?004 Unit the entries io6(10)..io12(16) are not valid
For KM2100/4 Valid entries are 'kmxMlA ' or 'kmxMlB'

Enumeration

Constraints:
range: 1-8

.1.3.6.1.4.1.164.3.2.3.2.16.2.1.2

prtIsdnEndpointPrtIdx

This attribute indicates a unique port number.
For MAXcess the values will be:
exPrt1(1),
exPrt2(2),
exPrt3(3),
exPrt4(4),
For KM-2100 the port index is calculated as follows:
100*Slot+Ch

SNMPv2-SMIInteger32

Enumerated Values:

2	noConnect
3	cl
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.16.2.1.3

prtIsdnEndpointIdx

Since more than one endpoint may be defined per
isdn entity, this field is a simple index.
It corresponds to isdnEndpointIdx in the isdn MIB.

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.16.2.1.4

prtIsdnEndpointTeiType

The type of TEI (Terminal Endpoint Identifier)
used for this Terminal Endpoint. In case of dynamic(1),
the TEI value is selected by the switch. In
case of static(2), a valid TEI value has to be
entered in the isdnEndpoi…

Enumerationr/w

Constraints:
range: 1-8

.1.3.6.1.4.1.164.3.2.3.2.16.2.1.5

prtIsdnEndpointTeiValue

When the TEI Type is static, the value of the TEI should be
between 0 and 63. Else, it is not selectable by user.
255 = notApplicable.
It corresponds to isdnEndpointTeiValue in the isdn MIB

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	r1x56eq56Kbps
2	r1x64eq64Kbps
3	r2x56eq112Kbps
4	r2x64eq128Kbps
5	r3x56eq168Kbps
6	r3x64eq192Kbps
7	r4x56eq224Kbps
8	r4x64eq256Kbps
9	r5x56eq280Kbps
10	r5x64eq320Kbps
11	r6x56eq336Kbps
12	r6x64eq384Kbps
13	r7x56eq392Kbps
14	r7x64eq448Kbps
15	r8x56eq448Kbps
16	r8x64eq512Kbps
17	r9x56eq504Kbps
18	r9x64eq576Kbps
19	r10x56eq560Kbps
20	r10x64eq640Kbps
21	r11x56eq616Kbps
22	r11x64eq704Kbps
23	r12x56eq672Kbps
24	r12x64eq768Kbps
25	r13x56eq728Kbps
26	r13x64eq832Kbps
27	r14x56eq784Kbps
28	r14x64eq896Kbps
29	r15x56eq840Kbps
30	r15x64eq960Kbps
31	r16x56eq896Kbps
32	r16x64eq1024Kbps
33	r17x56eq952Kbps
34	r17x64eq1088Kbps
35	r18x56eq1008Kbps
36	r18x64eq1152Kbps
37	r19x56eq1064Kbps
38	r19x64eq1216Kbps
39	r20x56eq1120Kbps
40	r20x64eq1280Kbps
41	r21x56eq1176Kbps
42	r21x64eq1344Kbps
43	r22x56eq1232Kbps
44	r22x64eq1408Kbps
45	r23x56eq1288Kbps
46	r23x64eq1472Kbps
47	r24x56eq1344Kbps
48	r24x64eq1536Kbps
49	r25x56eq1400Kbps
50	r25x64eq1600Kbps
51	r26x56eq1456Kbps
52	r26x64eq1664Kbps
53	r27x56eq1512Kbps
54	r27x64eq1728Kbps
55	r28x56eq1568Kbps
56	r28x64eq1792Kbps
57	r29x56eq1624Kbps
58	r29x64eq1856Kbps
59	r30x56eq1680Kbps
60	r30x64eq1920Kbps
61	r31x56eq1736Kbps
62	r31x64eq1984Kbps
100	noRate

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.16.2.1.6

prtIsdnEndpointSpid

The Service profile IDentifier (SPID) information
for this Terminal Endpoint. It is is composed of
9-20 numeric characters.
It corresponds to isdnEndpointSpid in the isdn MIB.

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.2.3.2.16.2.1.7

prtIsdnEndpointBearerCh

This is the selected dialing channel.
anyChannel - the system selects the dialing channel.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.16.2.1.8

prtIsdnEndpointRowStatus

This field indicates whether to consider this endpoint or not.
The only possible supported RowStatus vaules are
active (1) and destroy (6).

SNMPv2-TCRowStatusr/w

Constraints:
range: 1-255

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.3.2.3.2.16.2.1.9

prtIsdnDirectoryTable

table

.1.3.6.1.4.1.164.3.2.3.2.16.3 · 1 row entry · 14 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtIsdnDirectoryTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtIsdnDirectoryTable'

The write operation into the table objects is valid only
to the TmpCnfg entry.

prtIsdnDirectoryEntry row .1.3.6.1.4.1.164.3.2.3.2.16.3.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtIsdnDirectoryCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

Constraints:
range: 1-1

.1.3.6.1.4.1.164.3.2.3.2.16.3.1.1

prtIsdnDirectorySltIdx

This attribute indicates a unique slot position where
the card is inserted.
For MX300/30 ports:
io1(5) = isdn1(5) and io2(6) = isdn2(6).
In ?004 Unit the entries io6(10)..io12(16) are not valid
For KM2100/4 Valid entr…

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.16.3.1.2

prtIsdnDirectoryPrtIdx

For MAXcess this is the internal port number: 101, 102,....
For KM-2100 the port index is calculated as follows:
100*Slot+Ch

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.16.3.1.3

prtIsdnDirectoryLocalAddr

This is the local address associated with this
entry.
- For MX: Size=17 , Default=0 (17 characters)
- For KM: Size=20, Default=blank (20 characters)

OctetStringr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.16.3.1.4

prtIsdnDirectoryLocalSubAddr

This is the local subaddress associated with this
entry.
- For MX: Size=6 , Default=0 (6 characters)
- For KM: Size=4 , Default=blank (4 characters)

OctetStringr/w

Enumerated Values:

3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.16.3.1.5

prtIsdnDirectoryRemoteAddr

This is the remote address associated with this
entry.
- For MX: Size=17 , Default=0 (17 characters)
- For KM: Size=20, Default=blank (20 characters)

OctetStringr/w

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6
7	exPrt7
8	exPrt8
101	inPrt1
102	inPrt2
103	inPrt3
104	inPrt4
105	inPrt5
106	inPrt6
107	inPrt7
108	inPrt8
109	inPrt9
110	inPrt10
111	inPrt11
112	inPrt12
113	inPrt13
114	inPrt14
115	inPrt15
116	inPrt16
117	inPrt17
118	inPrt18
119	inPrt19
120	inPrt20
121	inPrt21
122	inPrt22
123	inPrt23
124	inPrt24
125	inPrt25
126	inPrt26
127	inPrt27
128	inPrt28
129	inPrt29
130	inPrt30
131	inPrt31
132	inPrt32
133	inPrt33
134	inPrt34
135	inPrt35
136	inPrt36
137	inPrt37
138	inPrt38
139	inPrt39
140	inPrt40
141	inPrt41
142	inPrt42
143	inPrt43
144	inPrt44
145	inPrt45
146	inPrt46
147	inPrt47
148	inPrt48
149	inPrt49
150	inPrt50
151	inPrt51
152	inPrt52
153	inPrt53
154	inPrt54
155	inPrt55
156	inPrt56
157	inPrt57
158	inPrt58
159	inPrt59
160	inPrt60
161	inPrt61
162	inPrt62
163	inPrt63
164	inPrt64
165	inPrt65
166	inPrt66
167	inPrt67
168	inPrt68
169	inPrt69
170	inPrt70
171	inPrt71
172	inPrt72
173	inPrt73
174	inPrt74
175	inPrt75
176	inPrt76
177	inPrt77
178	inPrt78
179	inPrt79
180	inPrt80
181	inPrt81
182	inPrt82
183	inPrt83
184	inPrt84

.1.3.6.1.4.1.164.3.2.3.2.16.3.1.6

prtIsdnDirectoryRemoteSubAddr

This is the remote subaddress associated with this
entry.
- For MX: Size=6 , Default=0 (6 characters)
- For KM: Size=4 , Default=blank (4 characters)

OctetStringr/w

Enumerated Values:

1	notApplicable
2	none
3	p1
4	p2
5	p3
6	p4
7	p5
8	perTS

.1.3.6.1.4.1.164.3.2.3.2.16.3.1.7

prtIsdnDirectoryPrtNu

This is the external port number connected to
this entry.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	none
2	trans
3	full

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.16.3.1.8

prtIsdnDirectoryTeiId

This is the abstract terminal id if relevant,
connected to this entry.

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	notSupported
3	forcedIdle
4	forcedBusy
5	busyIdle
6	idleBusy

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.16.3.1.9

prtIsdnDirectoryRowStatus

This is the status for the row. It allows to know
whether to consider this row or not.
The only possible supported RowStatus vaules are
active (1) and destroy (6).

SNMPv2-TCRowStatusr/w

Constraints:
range: 0-4

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.3.2.3.2.16.3.1.10

prtIsdnDirectoryLocalAddr2

This is the second local address associated with this
entry.
- For MX: Size=17 , Default=0 (17 characters)
- For KM: Size=20, Default=blank (20 characters)

OctetStringr/w

Constraints:
range: 0-4

.1.3.6.1.4.1.164.3.2.3.2.16.3.1.11

prtIsdnDirectoryLocalSubAddr2

This is the second local subaddress associated with this
entry.
- For MX: Size=6 , Default=0 (6 characters)
- For KM: Size=4 , Default=blank (4 characters)

OctetStringr/w

Enumerated Values:

1	notApplicable
2	leasedLine
3	v51
4	v52Master
5	v52Slave

.1.3.6.1.4.1.164.3.2.3.2.16.3.1.12

prtIsdnDirectoryRemoteAddr2

This is the second remote address associated with this
entry.
- For MX: Size=17 , Default=0 (17 characters)
- For KM: Size=20, Default=blank(20 characters)

OctetStringr/w

.1.3.6.1.4.1.164.3.2.3.2.16.3.1.13

prtIsdnDirectoryRemoteSubAddr2

This is the second remote subaddress associated with this
entry.
- For MX: Size=6 , Default=0 (6 characters)
- For KM: Size=4 , Default=blank (4 characters)

OctetStringr/w

.1.3.6.1.4.1.164.3.2.3.2.16.3.1.14

prtLogicalCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.17.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtLogicalCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtLogicalCnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtLogicalCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.17.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtLogicalCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

Enumerated Values:

1	notApplicable
2	none
3	framing
4	bpv

.1.3.6.1.4.1.164.3.2.3.2.17.1.1.1

prtLogicalSltIdx

Slot Index.
For ISDN BRI Ports of MX300/30,
io1(5) = isdn1(5) and io2(6) = isdn2(6).

Enumeration

Constraints:
range: 0-999

.1.3.6.1.4.1.164.3.2.3.2.17.1.1.2

prtLogicalPrtIdx

This attribute indicates a unique port number.
This port number should be an internal port number:
inPrt1(101)->inPrt50(150), linkSel1(200)->linkSel50(250),
encaps1(300)-> encaps50(350), huntGr1(101) -> huntGr10(110).

SNMPv2-SMIInteger32

Constraints:
range: 0-99

.1.3.6.1.4.1.164.3.2.3.2.17.1.1.3

prtLogicalConnect

This attribute indicates whether the port should be considered
in any of the mux algorithms.

Enumerationr/w

Constraints:
range: 0-257

.1.3.6.1.4.1.164.3.2.3.2.17.1.1.4

prtLogicalFunction

This parameter defines the function of the relevant channel.

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.17.1.1.5

prtLogicalRowStatus

This parameter allows the NMS to create/delete logical ports.
The only possible supported RowStatus vaules are
active (1) and destroy (6).

SNMPv2-TCRowStatusr/w

Enumerated Values:

1	notApplicable
2	no
3	yes

Description:

.1.3.6.1.4.1.164.3.2.3.2.17.1.1.6

linkSelectorCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.17.2 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk linkSelectorCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::linkSelectorCnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

linkSelectorCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.17.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

linkSelectorCnfgIdx

This attribute indicates the Idx of
the Cnfg (1..100) being accessed.
Idx 255 relates to the TmpCnfg.

Integer32

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.2.3.2.17.2.1.1

linkSelectorSltIdx

Slot Index

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.17.2.1.2

linkSelectorPrtIdx

This attribute indicates a unique port number.
This port number should be internal port number:
higher or equal to linkSeL1(201).

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.17.2.1.3

linkSelectorMaxIdleTime

Move to higher prioritized connected link
after this period of seconds of silence on the current link.
0=move immediately to higher prioritized connected link.
UNIT is seconds.

Integer32r/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.17.2.1.4

linkSelectorMode

If the link selector is in mode:
backup(2)=then the link with the lower priority will be
used in case of failure of the higher priority link,
bod(3)=bandwidth on demand or dynamic bandwidth allocation
m…

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
255	notApplicable

.1.3.6.1.4.1.164.3.2.3.2.17.2.1.5

linkSelectorRevert

If the link selector is in mode backup:
auto(2)=return automatically to Main link when it is OK.
manual(3)=stays connected to backup link.

Enumerationr/w

Enumerated Values:

1	exPrt1
2	exPrt2
3	exPrt3
4	exPrt4
5	exPrt5
6	exPrt6
7	exPrt7
8	exPrt8
9	exPrt9
10	exPrt10
11	exPrt11
12	exPrt12

.1.3.6.1.4.1.164.3.2.3.2.17.2.1.6

linkSelectorMinBUSession

Minimum duration of a backup session before
returning to Main Link. Relevant in Backup Mode and
when Revert is auto(2). Value 255 is for NEVER which
means never return to Main Link.
UNIT is minutes.

Integer32r/w

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.17.2.1.7

linkSelectorPLinkTable

table

.1.3.6.1.4.1.164.3.2.3.2.17.3 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk linkSelectorPLinkTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::linkSelectorPLinkTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

linkSelectorPLinkEntry row .1.3.6.1.4.1.164.3.2.3.2.17.3.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

pLinkCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

.1.3.6.1.4.1.164.3.2.3.2.17.3.1.1

pLinkSltIdx

Slot Index

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.17.3.1.2

pLinkPrtIdx

This attribute indicates a unique port number.
This port number should be the link selector number.

Integer32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.17.3.1.3

pLinkIdx

This index is the row number.

Integer32

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.17.3.1.4

pLinkSlotNu

The slot of the prioritized link.
For ISDN BRI ports of MX300/30,
io1(5) = isdn1(5) and io2(6) = isdn2(6).

Enumerationr/w

Enumerated Values:

1	exPrt1
2	exPrt2

.1.3.6.1.4.1.164.3.2.3.2.17.3.1.5

pLinkPortNu

The port of the prioritized link.
Value 100 is for noConnect.

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.17.3.1.6

pLinkPrioNu

The priority of the prioritized link.
MIN=1...., MAX=8.

Integer32r/w

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.17.3.1.7

pLinkVRate

The rate to use with this link.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.17.3.1.8

prtFrPlusCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.18.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtFrPlusCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtFrPlusCnfgTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.

prtFrPlusCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.18.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtFrPlusCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

Enumerated Values:

1	notApplicable
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12

.1.3.6.1.4.1.164.3.2.3.2.18.1.1.1

prtFrPlusSltIdx

Slot Index.
For ISDN BRI Ports of MX300/30,
io1(5) = isdn1(5) and io2(6) = isdn2(6).

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.18.1.1.2

prtFrPlusPrtIdx

This attribute indicates a unique port number.
This port number should be:
- for ISDN cards: inPrt1(101)->inPrt50(150)
- for MHS1 card : exPrt1(1)
- for MHS3, MLS3 cards: exPrt1(1)->exPrt3(3)
- for MLS6 cards: exPrt1(1…

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	bridge
3	bridgeAndStp
4	layer3SubnetSwitch

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.18.1.1.3

prtFrPlusNotSegmentedPriorities

This parameter is relevant only for FR+ protocol and
asks the MXcess NOT to segment data with specified
priorities: from LSB:
bit 1 is for priority 1,
bit 2 is for priority 2, .... till bit 7 for priority 7.
- a …

OctetStringr/w

.1.3.6.1.4.1.164.3.2.3.2.18.1.1.4

prtMl4CnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.19.1 · 1 row entry · 22 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtMl4CnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtMl4CnfgTable'

This is an extension table for MTML-4 card parameters.

prtMl4CnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.19.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtMl4CnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg. The write operation is valid only
to the TmpCnfg.

Integer32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.1

prtMl4SltIdx

This attribute indicates a unique slot position where
the module is inserted.

Enumeration

Constraints:
range: 1-65535

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.2

prtMl4PrtIdx

This attribute indicates a unique port number.

Enumeration

Enumerated Values:

1	notApplicable
2	unmodified
3	tag
4	doubleTag
5	untag

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.3

prtMl4SigProfile

This object indicates the Signaling Profile of the port.
none - when the Frame is G732N (no MF) or Unframed.
p1 = profile 1
p2 = profile 2
p3 = profile 3
p4 = profile 4
p5 = profile 5
perTS = when Signaling Profil…

Enumerationr/w

Constraints:
range: 0-4095

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.4

prtMl4CGA

This object selects the method used to signal the CGA state
to the other end, through the main link.
'none' - non-transparent mode. When one of the links
(main) will be in Out Of Service state, both
…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.5

prtMl4Oos

'idle' = '0' = on-hook, idle state
'busy' = '1' = off-hook, busy state
'forcedIdle' = SP = both A and B signaling bits are forced
to '0' during out-of-service periods.
'forcedBusy' = MK = both A and B sig…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.6

prtMl4VoiceOos

Voice Out-Of-Service code. Valid range: (0 - FF HEX).
For agents that do not support this feature, the value will
always be 0.

OctetStringr/w

Enumerated Values:

1	notApplicable
2	portBasedVlan
3	ieee802dot1q
4	ieee802dot1qTaggedOnly

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.7

prtMl4DataOos

Data Out-Of-Service code. Valid range: (0 - FF HEX).
For agents that do not support this feature, the value will
always be 0.

OctetStringr/w

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.8

prtMl4Service

Link Service.
leasedLine - usual TDM interface.
v51 - V5.1 interface.
v52Master - V5.2 Link to Local Exchange.
v52Slave - a ML that is transferred to the v52Master.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.9

prtMl4IpAddress

IP Address of the port.

RFC1155-SMIIpAddressr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.10

prtMl4IpMask

IP subnet mask of the port.

RFC1155-SMIIpAddressr/w

Enumerated Values:

2	off
3	on

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.11

prtMl4SignalingMode

Refers to the signaling mode of the port (or framer module).
notApplicable(1)- means that no framer is needed for this port (no signaling),
or that this object is not relevant.
cas(2) means Channel Associated Sig…

Enumerationr/w

Enumerated Values:

1	auto
2	dclA
3	dclB

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.12

prtMl4EchoCanceler

Echo canceler activation.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.13

prtMl4OosErrorSource

OOS (Out-of-Service) Error Source.
This object is applicable for T1 ports only.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.14

prtMl4OosEntryThreshold

This object defines the number of Errors per Second that determine the
minimum unacceptable noise level. This value will be the Entry Threshold
to the OOS (Out-of-Service) state.
This object is applicable only when prt…

Integer32r/w

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.15

prtMl4OosExitThreshold

This object defines the number of consecutive Error-Free-Seconds before
going from OOS state to Normal state. This value will be the Exit Threshold
from the OOS (Out-of-Service) state.
Units=seconds
This object is a…

Integer32r/w

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.16

prtMl4LogicalLinkId

This object defines for a V5.2 Master ML the Logical Link Id.
Valid values are: 0..256.
NA=257.

Integer32r/w

Enumerated Values:

1	off
2	dclA
3	dclB

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.17

prtMl4DedicatedTs

A unique number to identify Dedicated TS of the E1 port (V5.2).
It is applicable only when prtMl4Service=v52Slave and
prtExPh1MlInbandMng selected is dedicatedTs, dedicatedPpp or dedicatedFr.
1..31 - Dedicated TS of E1…

Integer32r/w

Enumerated Values:

1	off
2	dclA
3	dclB

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.18

prtMl4RemCrc

This object indicates whether the E1 of the Remote device
connected to this E1 port, will have CRC-4 or not.

Enumerationr/w

Enumerated Values:

0	cnfgMismatch
1	swMismatch
2	cardAAbsent
3	cardBAbsent
4	lossOfCommunication
5	hwMismatch
6	cnfgUpdate
7	swUpdate

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.19

prtMl4CrossConnectLevel

This object indicates whether the cross connect is
on DS1 or DS0 (time-slots) level.
When cross connect level is ds1, Destination Slot
is indicated by prtGenCnfgLinkToSlot,
Destination Port is indicated by prtGenCnf…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.20

prtMl4PppEchoFailDetection

This object indicates whether the PPP Echo is taken into account
for its Fail Detection.
This object is relevant when Inband Mng between devices is Dedicated TS PPP.
Default=Disable.
Enable - will be selected main…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.21

prtMl4EcanCasControl

This object enables/disables ECAN (Echo Canceller) control activation/deactivation
sent via the A, B, C, D multiframe signaling BITs.

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.2.3.2.19.1.1.22

prtAcmCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.20.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtAcmCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtAcmCnfgTable'

This is a table for ACM port parameters.

prtAcmCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.20.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtAcmCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg. The write operation is valid only
to the TmpCnfg.

Integer32

.1.3.6.1.4.1.164.3.2.3.2.20.1.1.1

prtAcmSltIdx

This attribute indicates a unique slot position where
the module is inserted.

Enumeration

Enumerated Values:

1	error
2	warning

.1.3.6.1.4.1.164.3.2.3.2.20.1.1.2

prtAcmPrtIdx

This attribute indicates a unique port number.

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.20.1.1.3

prtAcmConnect

This attribute indicates whether the port should be
connected or not. Only a connected port can perform activity.

Enumerationr/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.2.3.2.20.1.1.4

prtAcmActiveState

This attribute indicates the Electric Active State of the port.

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.20.1.1.5

prtAcmAlrString

Alarm string selected by user for the Inbound ports.
This object is applicable only for the Inbound Ports: ext-5..ext-12.
For the Outbound Ports (ext-1..ext-4), the size of this string will be 0.

OctetStringr/w

.1.3.6.1.4.1.164.3.2.3.2.20.1.1.6

prtE2CnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.21.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtE2CnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtE2CnfgTable'

This is a table for E2 port parameters.

prtE2CnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.21.1.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
prtE2CnfgIdx This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg.	Integer32	`.1.3.6.1.4.1.164.3.2.3.2.21.1.1.1`
prtE2SltIdx This attribute indicates a unique slot position where the module is inserted.	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.21.1.1.2`
prtE2PrtIdx This attribute indicates a unique port number.	Enumeration	`.1.3.6.1.4.1.164.3.2.3.2.21.1.1.3`
prtE2Connect This attribute indicates whether the port should be connected or not. Only a connected port can perform activity.	Enumerationr/w	`.1.3.6.1.4.1.164.3.2.3.2.21.1.1.4`
prtE2MngOnNationalBit This attribute indicates whether National Bit will be used for Management or not.	Enumerationr/w	`.1.3.6.1.4.1.164.3.2.3.2.21.1.1.5`

prtLanWanCnfgTable

table

.1.3.6.1.4.1.164.3.2.3.2.22.1 · 1 row entry · 14 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtLanWanCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtLanWanCnfgTable'

This is a table for Lan-Wan port parameters.

prtLanWanCnfgEntry row .1.3.6.1.4.1.164.3.2.3.2.22.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtLanWanCnfgIdx

This object indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg. The write operation is valid only
to the TmpCnfg.

Integer32

Enumerated Values:

1	free
2	physical
3	virtual

.1.3.6.1.4.1.164.3.2.3.2.22.1.1.1

prtLanWanSltIdx

This object indicates a unique slot position where the module is inserted.

Enumeration

.1.3.6.1.4.1.164.3.2.3.2.22.1.1.2

prtLanWanPrtIdx

This object indicates a unique number to identify a port
in a specific card.
Generally, for MP-210X/2200, the Port Index will be according to the
external/internal port number:
- exPrtX : X
- inPrtX : 100 + X
For FCD…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.22.1.1.3

prtLanWanMode

This object determines the working mode of this port.
For FCD155, layer3SubnetSwitch is not applicable

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.22.1.1.4

prtLanWanDestIf

This object determines the Destination Interface for the frames
received by this port.
- Switching Table = 100 (it means that the destination interface
will be determined by the Switching Ta…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.22.1.1.5

prtLanWanEgressVlanMode

This object determines what to do with the VLAN frames that exit
via the WAN side of the port.
This object is not applicable when prtLanWanMode=l3SubnetSwitch(4).

Enumerationr/w

Enumerated Values:

1	notApplicable
2	noEnforcement
3	primary
4	secondary

.1.3.6.1.4.1.164.3.2.3.2.22.1.1.6

prtLanWanL2Protocol

L2 Protocol.
When prtLanWanMode=l3SubnetSwitch(4), the only valid value is ppp(3).

Enumerationr/w

Enumerated Values:

1	notApplicable
2	off
3	on

.1.3.6.1.4.1.164.3.2.3.2.22.1.1.7

prtLanWanStpPriority

The value of the priority field which is contained in the first
(in network byte order) octet of the (2 octet long) Port ID.

Integer32r/w

Enumerated Values:

1	notApplicable
2	off
3	on

.1.3.6.1.4.1.164.3.2.3.2.22.1.1.8

prtLanWanStpCost

The contribution of this port to the path cost of paths towards
the spanning tree root which include this port. 802.1D-1990 recommends
that the default value of this parameter be in inverse proportion
to the speed o…

Integer32r/w

.1.3.6.1.4.1.164.3.2.3.2.22.1.1.9

prtLanWanToLanVlanMode

This object determines what to do with the VLAN frames that come from
WAN side of the port and exit towards one of the LAN ports.
This object is applicable only when prtLanWanDestIf=100 or 101
(Switching Table or inPrt…

Enumerationr/w

.1.3.6.1.4.1.164.3.2.3.2.22.1.1.10

prtLanWanVlanId

This is the VLAN Id attached to a frame, when the relevant
Vlan Mode (prtLanWanEgressVlanMode or prtLanWanToLanVlanMode) is
tag or doubleTag.
0=not applicable.

Integer32r/w

.1.3.6.1.4.1.164.3.2.3.2.22.1.1.11

prtLanWanVlanPriority

This is the VLAN Priority attached to a frame, when the relevant
Vlan Mode (prtLanWanEgressVlanMode or prtLanWanToLanVlanMode) is
tag or doubleTag.
Valid values: 0..7
255=not applicable.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.22.1.1.12

prtLanWanMtu

The size of the largest packet which can be sent/received on the interface,
specified in octets.
Valid values change per device.
0=not applicable.

SNMPv2-SMIInteger32r/w

Enumerated Values:

3	event
4	minor
5	major
6	warning
7	critical

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.2.3.2.22.1.1.13

prtLanWanVlanType

This oject indicates type of VLAN this port is assigned to.
Port Base Vlan parameters are defined by objects under
radBridgePortBaseVlan

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.2.3.2.22.1.1.14

sysDclTable

table

.1.3.6.1.4.1.164.3.3.1.2.2.1 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sysDclTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sysDclTable'

All the entries of this table are identical (have the 
same value) for all the configurations (1..255) except 
the TmpCnfg.
The write operation into the Table Objects is valid only
for the TmpCnfg entry.

sysDclEntry row .1.3.6.1.4.1.164.3.3.1.2.2.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

sysDclCnfgIdx

This object indicates the Idx of the Cnfg(1..255)
being accessed ; Idx of 255 relates to the TmpCnfg.
This object is identical for all the configurations (1..255).
Only the TmpCnf(255) might have a different value.
Fo…

Integer32

.1.3.6.1.4.1.164.3.3.1.2.2.1.1.1

sysDclRedundancy

DCL redundancy desired state.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.1.2.2.1.1.2

sysDclActiveCl

Active desired DCL.
When 'auto' is selected, the system automatically selects
the active DCL.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.1.2.2.1.1.3

sysDclFlipDelay

If one DCL flip occurred and a second one should be
performed, the time from the previous flip is checked.
If the time is shorter than the delay specified here,
the system should delay the flip operation until time reac…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.2.2.1.1.4

sysDclFlipUponStnClk

This object allows user to decide (yes/no) if Agent should Flip from
one DCL card to another, when there is Station Clock Fail in
the Online DCL card.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.1.2.2.1.1.5

sysDclChFailThreshold

This object indicates the number of failed channels that will trigger the
redundancy procedure.

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	off
3	event
4	minor
5	major
6	warning
7	critical

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.2.2.1.1.6

sysDclChPriority

This object indicates the Priority for all the channels in the Main Access
(Common Logic) card. Each channel is represented by 1 bit.
The order of the bits in each byte is from Right to Left (LSB Bit to MSB)
starting …

OctetStringr/w

Enumerated Values:

1	psA
2	psB
3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
17	io13
18	io14
19	io15
20	local
21	psC
101	kmxPsA
102	kmxPsB
103	kmxMlA
104	kmxMlB
105	kmxCl
106	kmxOpt
107	kmxIO1
108	kmxIO2
109	kmxIO3
110	kmxIO4
111	kmxIO5
112	kmxIO6
113	kmxIO7
114	kmxIO8
115	kmxIO9
116	kmxIO10
117	kmxIO11
118	kmxIO12
120	remote
255	notApplicable

.1.3.6.1.4.1.164.3.3.1.2.2.1.1.7

sysDclConfigDownloadSrc

In case of mismatch between the 2 CL card's configuration, the user can decide
which card has the suitable configuration.
The selected configuration will be downloaded from card A to card B
if the value is dclA(2) or f…

Enumerationr/w

.1.3.6.1.4.1.164.3.3.1.2.2.1.1.8

sysDclSwDownloadSrc

In case of mismatch between the 2 CL card's software, the user can decide
which card has the suitable SW.
The selected SW will be downloaded from card A to card B if the value is dclA(2)
or from card B to card A if the…

Enumerationr/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.3.1.2.2.1.1.9

sysDclRedundancyStatus

Bit map representing current Redundancy Status.
bit 0 - Indicates mismatch between the 2 CL cards' Configuration
bit 1 - Indicates mismatch between the 2 CL cards' Software.
bit 2 - Indicates CL card A Absence.
bi…

Bits

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.3.1.2.2.1.1.10

sysDclCopyDbTable

table

.1.3.6.1.4.1.164.3.3.1.2.2.3 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sysDclCopyDbTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sysDclCopyDbTable'

This table enables to copy a cofiguration from the Offline
Dcl to the Online Dcl.

sysDclCopyDbEntry row .1.3.6.1.4.1.164.3.3.1.2.2.3.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
sysDclCopyDbIdx This object indicates the Idx of the Cnfg(1..255) being accessed.	Integer32	`.1.3.6.1.4.1.164.3.3.1.2.2.3.1.1`
sysDclCopyDbCmd When this command is sent to the agent, on(3), the Database specified (Db Idx), will be copied from the Offline Dcl to the Online Dcl. Afterwards the value of this object will automatically change to off(2).	Enumerationr/w	`.1.3.6.1.4.1.164.3.3.1.2.2.3.1.2`

sysSErrListTable

table

.1.3.6.1.4.1.164.3.3.1.3.13 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sysSErrListTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sysSErrListTable'

A table.

sysSErrListEntry row .1.3.6.1.4.1.164.3.3.1.3.13.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

sysSErrType

The errors are recorded in the agent, in two separate lists,
according to their type: error or warning.

Enumeration

Enumerated Values:

1	none
2	internal
3	rxClk
4	station
5	lbt
6	ntr
7	adaptive
8	stationB
9	automatic
10	system
11	sSubSystem
12	recovered
255	notApplicable

.1.3.6.1.4.1.164.3.3.1.3.13.1.1

sysSErrIdx

Unique index number to identify an entry in the error
or warning list .
The maximum value cannot exceed the value of
'sysSNoOfSanityCheckErr' (actually, the sum of the Errors
list max. index and the Warning list max. …

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.3.13.1.2

sysSErrDescription

This object is a full text description of the sanity check
error including error code, IO slot and port numbers related to
the code .

OctetString

Enumerated Values:

1	notApplicable
2	f1544Khz
3	f2048Khz

.1.3.6.1.4.1.164.3.3.1.3.13.1.3

sysSRdnFlipTable

table

.1.3.6.1.4.1.164.3.3.1.3.18 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sysSRdnFlipTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sysSRdnFlipTable'

This table includes all the Flip events due to I/O Redundancy since
last Clear command of this table.

sysSRdnFlipEntry row .1.3.6.1.4.1.164.3.3.1.3.18.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

sysSRdnFlipIdx

Unique index number to identify an entry in the Redundancy Flip list.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	normal
3	yCable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.3.18.1.1

sysSRdnFlipSlot

The slot number from which Flip was performed.

Enumeration

Enumerated Values:

1	notApplicable
2	disabled
3	enabled

.1.3.6.1.4.1.164.3.3.1.3.18.1.2

sysSRdnFlipPort

The port number from which Flip was performed.
For DXC:
For external ports the convention used will be:
- first two digits will be: (IO slot number+10)
- last one/two digits will be the port number within the
card, in …

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.3.18.1.3

sysSRdnFlipCause

The last cause that caused the Flip from the Slot (Port)
of sysSRdnSlot, sysSRdnPort.

SNMPv2-TCDisplayString

Enumerated Values:

1	notApplicable
3	clA
4	clB

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.3.1.3.18.1.4

sysSRdnFlipDate

Flip event Date. The format will be the one selected by user for
sysSDateFormat.

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.3.1.3.18.1.5

sysSRdnFlipTime

Flip event Time. The format will be hh:mm:ss.

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.3.1.3.18.1.6

sysSBusTable

table

.1.3.6.1.4.1.164.3.3.1.3.21 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sysSBusTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sysSBusTable'

This table includes data and status about the internal DXC BUS.

sysSBusEntry row .1.3.6.1.4.1.164.3.3.1.3.21.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

sysSBusPortIdx

The DXC BUS port number:
- first two digits will be: (IO slot number+10)
- last one/two digits will be the Bus port number, in odd numbers:
port1 = 1
port2 = 3
Example: port2 of IO slot 11 will be: 213.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	bidirectional
3	unidirectional

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.3.21.1.1

sysSBusStatus

The Status of sysSBusPortIdx.
free - not used
physical - captured by the port of the card physically installed
virtual - captured virtually by another port. Example: DIM port
(by Destination) or by Transp…

Enumeration

Enumerated Values:

1	notApplicable
2	te
3	nt

.1.3.6.1.4.1.164.3.3.1.3.21.1.2

sysSBusCapturePort

The Port that Captured the sysSBusPortIdx.
- if sysSBusStatus=free, the value will be 'none'=0
- else, if sysSBusStatus=fixed, the value will be: sysSBusPortIdx
- else, the value will be according to the port index …

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	none
3	proprietary
4	rip2
5	rip1
6	rip1and2

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.3.21.1.3

sysSBusUtilization

Utilization of sysSBusPortIdx resources, in percent [%].

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.3.21.1.4

sysSRdnCmdTable

table

.1.3.6.1.4.1.164.3.3.1.3.22 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sysSRdnCmdTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sysSRdnCmdTable'

This table includes commands used for IO Redundancy.

sysSRdnCmdEntry row .1.3.6.1.4.1.164.3.3.1.3.22.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

sysSRdnEnforcedChannel

This is a command to override all switching considerations
and enforce use of primary/ secondary connection only.
noEnforcement - cancels the state of override and goes back to
usual switching cons…

Enumerationr/w

Enumerated Values:

2	enableAll
3	enableVoiceOnly
4	enableVoiceAndMng

.1.3.6.1.4.1.164.3.3.1.3.22.1.1

sysSRdnLockFlip

This is a command to lock the Redundancy flip for this redundancy couple.
Default = off(2).

Enumerationr/w

.1.3.6.1.4.1.164.3.3.1.3.22.1.2

sysSRdnManualFlip

This is a command to move to manual Redundancy flip mode for this redundancy couple.
Default = off(2).

Enumerationr/w

Enumerated Values:

2	auto
3	manual

.1.3.6.1.4.1.164.3.3.1.3.22.1.3

sysSAlrTable

table

.1.3.6.1.4.1.164.3.3.1.4.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sysSAlrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sysSAlrTable'

List of system level current existing alarms .

sysSAlrEntry row .1.3.6.1.4.1.164.3.3.1.4.1.1

An entry in table.

Indexes

sysCRdnCnfgIdx sysCRdnPrimeSlot sysCRdnPrimePort

Column Syntax OID

sysSAlrIdx

An index number of the current system alarms.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.4.1.1.1

sysSAlrCode

This object indicates a code related to a specific
alarm description. The list of codes and their related
descriptions will be sent to NMS request (for display purpose)
by alrGenTable.

SNMPv2-SMIInteger32

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
17	io13
18	io14
19	io15
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.4.1.1.2

sysSAlrState

This object indicates the alarm Severity.

Enumeration

.1.3.6.1.4.1.164.3.3.1.4.1.1.3

sysSAlarmMask

Alarm Mask is : on/off.

Enumeration

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
17	io13
18	io14
19	io15
255	notApplicable

.1.3.6.1.4.1.164.3.3.1.4.1.1.4

sysSAlarmInvert

Alarm Invert is : on/off.

Enumeration

.1.3.6.1.4.1.164.3.3.1.4.1.1.5

sysSAlarmOnOff

Alarm state is : on/off.

Enumeration

Enumerated Values:

2	dualCableAIS
3	yCable
4	dualCableParallelTx
5	backup
6	singleSlotProtection
7	onePlusOne
8	oneToOne
9	linkAggregation
10	manual

.1.3.6.1.4.1.164.3.3.1.4.1.1.6

sysSAlarmCounter

A counter - how many times the alarm occured (ON) since last
clear operation or since last Reset.

SNMPv2-SMIInteger32

Enumerated Values:

2	auto
3	manual
4	nonRevertive

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.4.1.1.7

sysBufferAlrTable

table

.1.3.6.1.4.1.164.3.3.1.5.1 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sysBufferAlrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sysBufferAlrTable'

List of current existing alarms (of all levels).

sysBufferAlrEntry row .1.3.6.1.4.1.164.3.3.1.5.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

sysBufferAlrIdx

An index number of the current alarms.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.5.1.1.1

sysBufferAlrCode

This object indicates a code related to a specific
alarm description. The list of codes and thir related
descriptions will be known by the NMS (for display purpose)
and will appear in the unit's user manual.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	primary
3	secondary

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.5.1.1.2

sysBufferAlrState

This object indicates the alarm type.
minor/major/warning/critical - indicates appearance of the problem
and the type.
event - indicates occurence of an event.
off - indicates disappearance …

Enumeration

Enumerated Values:

1	notApplicable
2	biDirectional
3	uniDirectional
4	linkAggregation

.1.3.6.1.4.1.164.3.3.1.5.1.1.3

sysBufferAlrSlot

The slot number this alarm refers to.
When the alarm refers to a system function OR the DACS agent
is a stand-alone unit, the value will be 'notApplicable(255)'.
local/remote - for OP-4 device.

Enumeration

.1.3.6.1.4.1.164.3.3.1.5.1.1.4

sysBufferAlrPort

The port number this alarm refers to.
If the port number is irrelevant to this alarm (if it is
a system/card level alarm) the value will be 9999.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.5.1.1.5

sysBufferAlrDate

The date when the alarm occured. The format will be according
to sysSDateFormat.

OctetString

.1.3.6.1.4.1.164.3.3.1.5.1.1.6

sysBufferAlrTime

The time when the alarm occured.

OctetString

.1.3.6.1.4.1.164.3.3.1.5.1.1.7

sysBufferAlrUpTime

The time when the alarm occured.
This parameter holds the sysUpTime value when the alarm occured.

RFC1155-SMITimeTicks

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.3.1.5.1.1.8

sysBufferAlrInfo

This parameter includes information about the alarm (additional to the Description).

SNMP-FRAMEWORK-MIBSnmpAdminString

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.3.3.1.5.1.1.9

sysCClkSrcTable

table

.1.3.6.1.4.1.164.3.3.1.6.1 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sysCClkSrcTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sysCClkSrcTable'

All the entries of this table are identical (have the 
same value) for all the configurations (1..255) except 
the TmpCnfg.
For devices with more than one configuration:
The write operation into the Table Objects is valid only
for the TmpCnfg entry.

sysCClkSrcEntry row .1.3.6.1.4.1.164.3.3.1.6.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

sysCClkCnfgIdx

This attribute indicates the Idx of the Cnfg being
accessed ; Idx of 255 relates to the TmpCnfg.
It can be also a combination of the configuration number and the
Card/Port/Other System index.

Integer32

.1.3.6.1.4.1.164.3.3.1.6.1.1.1

sysCClkSrcIdx

An index in the table. There are only two entries in the
table.
master - refers Master clock parameters
fallback - refers Fallback clock parameters

Enumeration

.1.3.6.1.4.1.164.3.3.1.6.1.1.2

sysCClkSrcMode

This entry indicates the source the nodal timing is
locked to.
none - is an invalid option for Master clock.
internal - is an invalid option for Fallback clock .
station - is an invalid option for a stand-alone un…

Enumerationr/w

Constraints:
range: 0-30

.1.3.6.1.4.1.164.3.3.1.6.1.1.3

sysCClkSrcPrt

This entry is valid only when working in rxClk mode
(for IPmux1000 this entry will be valid whe working in LBT mode).

For ACE2002 in case of invalid entry the return value
will be 0.
For other products …

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.6.1.1.4

sysCClkStationFreq

This entry indicates the frequency of the station clock
when the source is 'station'.
The value will be applicable only when the sysCClkSrcMode is
'station'.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.1.6.1.1.5

sysCClkRevertiveTimeout

The time in seconds in which the system will monitor the higher
level clock source, before decision to revert to that clock.
In case the time is zero, revertive mode will be disabled.

SNMPv2-SMIInteger32r/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.3.1.6.1.1.6

sysCClkStationIf

This entry indicates the electrical interface connected to the
station clock, when the source is 'station'.
The value will be applicable only when the sysCClkSrcMode is
'station'.

Enumerationr/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.3.1.6.1.1.7

sysCClkStationCableMode

This parameter indicates whether both Station clocks get their
clock from the same source (Y Cable)or each one get its clock independently.
The value will be applicable only when the sysCClkSrcMode is 'station'.

Enumerationr/w

Enumerated Values:

1	disable
2	enable

.1.3.6.1.4.1.164.3.3.1.6.1.1.8

sysCClkStationOutState

This parameter indicates whether station clock can
send its clock to another device.
The value will be applicable only when the sysCClkSrcMode is 'station'.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.1.6.1.1.9

sysCClkSsmBased

This parameter indicates whether clock source
will be selected based on receive clock quality,
indicated in S1 byte inside SONET/SDH overhead,
(encoded as SSM - Synchronization Status Messaging).
It is relevant only …

Enumerationr/w

.1.3.6.1.4.1.164.3.3.1.6.1.1.10

sysCClkSSubsystemSlot

This entry indicates the Slot from which the S Subsytem Source
will be taken.
The value will be applicable only when the sysCClkSrcMode is
'sSubsystem'.

Enumerationr/w

Enumerated Values:

1	psA
2	psB
3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
17	io13
18	io14
19	io15
20	psC
101	kmxPsA
102	kmxPsB
103	kmxMlA
104	kmxMlB
105	kmxCl
106	kmxOpt
107	kmxIO1
108	kmxIO2
109	kmxIO3
110	kmxIO4
111	kmxIO5
112	kmxIO6
113	kmxIO7
114	kmxIO8
115	kmxIO9
116	kmxIO10
117	kmxIO11
118	kmxIO12
255	notApplicable

.1.3.6.1.4.1.164.3.3.1.6.1.1.11

sysCClkRecoveredID

This entry indicates the Recovered Clock ID.
The value will be applicable only when sysCClkSrcMode is 'recovered'.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	unknown
2	empty
10	psAC
11	psDC
18	gCl1
19	gCl2
20	dCl
21	kCl
22	dcl2
23	dcl2Eth
24	kClEth
25	dcl3
26	dcl3Eth
28	d4T1
29	d8T1
30	dT1DSU
31	dT1CSU
32	dE1DSU
33	dE1LTU
34	dE1aDSU
35	dE1aLTU
36	dT1F
37	dE1F
38	d4E1
39	d8E1
40	dE1Hdsl
41	dT1Hdsl
42	dE1HdslS
43	dT1HdslS
44	d16gsdsl
45	d8sl
46	d4slStuC
47	d4slStuR
50	kML1
51	kML2
52	kML3
53	kML4
54	kML5
55	kML6
56	kML7
57	kML8
59	kML10
60	kMLF
61	kML10New
62	kML11RJ45
63	kML11FO
70	kLS1
71	kLS1New
72	kLS2
80	kTRE
81	kMBE
82	kMBENew
83	fLAN
90	kai
91	kdi
92	kdiCH
100	dHS2
101	d8U
102	d16U
103	d4HS
104	d8HS
110	kHS1
111	kHS2
112	kHSU1
113	kHSU2
114	kHS703
130	kVC1EM
131	kVC1FXO
132	kVC1FXS
133	kVC1MEM
134	kVC1MFXO
135	kVC1MFXS
136	kVC1MFXSW
137	kVC2EM
138	kVC2FXO
139	kVC2FXS
140	kVC2s1EM
141	kVC2s1FXO
142	kVC2s1FXS
143	kVC3EM
144	kVC3FXO
145	kVC3FXS
146	kVC3S0
170	kVF1EM
171	kVF1FXO
172	kVF1FXS
173	kVF3EM
174	kVF3FXO
175	kVF3FXS
176	kVF4EM
177	kVF4FXO
178	kVF4FXS
179	kVF4FXSW
180	kVF4S0
181	kVF5PbxE1
182	kVF5E1PbxSlave
183	kVF5PbxT1
184	kVF5T1PbxSlave
185	kVF5PbxE1New
186	kVF5E1PbxSlaveNew
187	kVF5PbxT1New
188	kVF5T1PbxSlaveNew
189	kVF4FXO3
190	kVF4FXS3
191	kVF4NS0
192	kVF6E1s16
193	kVF6E1s31
194	kVF6T1s12
195	kVF6T1s24
196	kVF8EM
197	kVF8FXO
198	kVF8FXS
200	dimETUR
201	dimV35
202	dimRS422
203	dimRS530
204	dimHssi
205	dimX21
206	dim10BaseT
207	dimE1
208	dim100
209	dt3G747
210	dt3
211	dt3f
212	de3
213	de3f
214	dstm1s1
215	dstm1s2
216	fSTM1
217	dstm1
218	dstm1R
219	f2stm1
220	gstm1
221	goc3
222	gstm1D
223	goc3D
230	laSUB
231	laVEM
232	laVFXO
233	laVFXS
234	laV11
235	laV24
236	laV35
237	laT1
238	laT1Vxx
239	laE1
240	laE1Vxx
241	laISDN
242	laVxx
243	laEth
244	laISDNwBU
245	laIsdnNT
246	laIsdnNTwBU
247	laIsdnTE
248	laFXSwBU
249	laFXSs
250	laFXSwBUs
251	laIsdnNTs
252	laIsdnNTwBUs
253	laIsdnTEs
254	laDp
255	laSdsl
256	laSdslDp
257	laAdslA
258	laAdslADp
259	laAdslB
260	laAdslBDp
261	laShdsl
262	laShdslDp
263	laT1b
264	laT1bDp
265	laIsdnTEwBU
266	laIsdnTEwBUs
267	laShdsl4w
268	laShdsl4wDp
269	laEthSwitch
270	serverE1
271	serverT1
272	serverE1Pw
273	serverT1Pw
280	gigabitEth
281	gigabitEth2
282	eth2
283	gigabitEth8
284	eth8
290	channelizedT3Pw1
300	cesT128
301	cesE128
302	cesT1Pw28
303	cesE1Pw28
310	vmxE1VeDe
311	vmxE1VeDi
312	vmxE1ViDe
313	vmxE1ViDi
314	vmxT1VeDe
315	vmxT1VeDi
316	vmxT1ViDe
317	vmxT1ViDi
318	vc12E1UeNe
319	vc12E1UeNi
320	vc12E1UiNe
321	vc12E1UiNi
322	vc12T1UeNe
323	vc12T1UeNi
324	vc12T1UiNe
325	vc12T1UiNi
326	vca16E1UeNe
327	vca16E1UeNi
328	vca16E1UiNe
329	vca16E1UiNi
330	vca16T1UeNe
331	vca16T1UeNi
332	vca16T1UiNe
333	vca16T1UiNi
334	vca12E1UeNe
335	vca12E1UeNi
336	vca12E1UiNe
337	vca12E1UiNi
338	vca12T1UeNe
339	vca12T1UeNi
340	vca12T1UiNe
341	vca12T1UiNi
342	vmg16E1Ue
343	vmg16E1Ui
344	vmg16T1Ue
345	vmg16T1Ui
346	vmg12E1Ue
347	vmg12E1Ui
348	vmg12T1Ue
349	vmg12T1Ui

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.3.1.6.1.1.12

sysCnfgTable

table

.1.3.6.1.4.1.164.3.3.1.6.2 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sysCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sysCnfgTable'

All the entries of this table are identical (have the 
same value) for all the configurations (1..255) except 
the TmpCnfg.
The write operation into the Table Objects is valid only
for the TmpCnfg entry.

sysCnfgEntry row .1.3.6.1.4.1.164.3.3.1.6.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

sysCnfgIdx

This attribute indicates the Idx of the Cnfg(1..255) being
accessed ; Idx of 255 relates to the TmpCnfg.
For Gmux2000 the range limitation (1..255) was discarded
since the Idx is computed as: <IO Card No.> x 1000 +…

SNMPv2-SMIInteger32

Enumerated Values:

2	off
3	major
4	minor
5	event
6	warning
7	critical

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.6.2.1.1

sysCMatrixMode

Indicates the TS Matrix Mode:
bidirectional - TS Assignment Matrix is symmetric.
unidirectional - TS Assignment Matrix can be asymmetric.
notApplicable - for agents that do not support this feature.

Enumerationr/w

Enumerated Values:

2	off
3	major
4	minor
5	event
6	warning
7	critical

.1.3.6.1.4.1.164.3.3.1.6.2.1.2

sysCIsdnFormat

ISDN format. This parameter controls the operation mode of
the ISDN ports.
te - ISDN timing is derived from the signal received
from the equipment it is connected to.
nt - timing of the transmit path is locked to t…

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.3.1.6.2.1.3

sysCRoutingOnEth

Mng Routing Protocol on the online CL Ethernet port,
or on device Ethernet port dedicated for mangement.

Enumerationr/w

Enumerated Values:

2	fail
3	ok

.1.3.6.1.4.1.164.3.3.1.6.2.1.4

sysCAutoConfigEnable

This object enables user to enable/disable activating
the Auto Configuration. When Auto Configuration is activated,
the device learns its configuration Automatically from the Net
it is connected to.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	offline
3	online

.1.3.6.1.4.1.164.3.3.1.6.2.1.5

sysCIntTsAllocMode

This object enables user to select the mode of Internal TS
Allocation.
static - user has to select for each Dynamic card port, the
Maximum TSs expected to be connected (including future
growth). This…

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.3.1.6.2.1.6

sysCBuPrimaryPort

This object enables the user to configure a Backup mechanism.
If a backup mechanism exists, it is possible to configure the primary port.
The traffic will flow via the primary port when the port functionality is OK.
…

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.3.1.6.2.1.7

sysCEnableLanOverTdm

This object enables/disables transferring traffic from the LAN port
to the TDM port. It is possible to enable only part of the traffic on the
TDM port for security reasons or in order to minimize the bandwidth .

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.3.1.6.2.1.8

sysCSs7FisuSuppression

SS7 Suppresion is used for SS7 Spoofing.
The SS7 spoofing terminates the keep alive messages from the local VMUX
without sending them over the network, thus improving the bandwidth utilization.
FISU means Fill in Se…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.6.2.1.9

sysCBuRecMode

Recovery Mode. This object determines if after recovery
of the Primary Link (used in Vmux) it will become on-line again or not:
auto - automatic. In this case, the failed Link will become
on-line again after recover…

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.3.1.6.2.1.10

sysCRdnTable

table

.1.3.6.1.4.1.164.3.3.1.6.3 · 1 row entry · 23 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sysCRdnTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sysCRdnTable'

Configuration of all Redundant I/O cards and ports.
The write operation into the table objects is valid only
for the TmpCnfg.
A Slot/Port that have no Redundancy, will not exist in this
table.

sysCRdnEntry row .1.3.6.1.4.1.164.3.3.1.6.3.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

sysCRdnCnfgIdx

This object indicates the Idx of the Cnfg(1..255) being
accessed ; Idx of 255 relates to the TmpCnfg.

SNMPv2-SMIInteger32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.3.1.6.3.1.1

sysCRdnPrimeSlot

The slot number of the Primary card of Redundancy.
The Primary card should be the card that user wishes to be
the online card (usually the more important one).
For some Redundancy modes the importance of the redundant
…

Enumeration

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.3.1.6.3.1.2

sysCRdnPrimePort

The port number.
For DXC:
For external ports the convention used will be:
- first two digits will be: (IO slot number+10)
- last one/two digits will be the port number within the
card, in odd numbers:
port1 = 1
port2 =…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.6.3.1.3

sysCRdnSecSlot

The slot number of the Secondary card of Redundancy matching
the Primary slot.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.1.6.3.1.4

sysCRdnSecPort

SNMPv2-SMIInteger32r/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.3.1.6.3.1.5

sysCRdnMode

Redundancy Mode.
DXC supports: yCable(3), singleSlotProtection(6) and dualCableParallelTx(4)
MP supports: yCable(3), dualCableParallelTx(4), onePlusOne(7) and oneToOne(8).
(dualCableAIS and backup wer…

Enumerationr/w

Enumerated Values:

1	psA
2	psB
3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
17	io13
18	io14
19	io15
20	psC
101	kmxPsA
102	kmxPsB
103	kmxMlA
104	kmxMlB
105	kmxCl
106	kmxOpt
107	kmxIO1
108	kmxIO2
109	kmxIO3
110	kmxIO4
111	kmxIO5
112	kmxIO6
113	kmxIO7
114	kmxIO8
115	kmxIO9
116	kmxIO10
117	kmxIO11
118	kmxIO12
255	notApplicable

.1.3.6.1.4.1.164.3.3.1.6.3.1.6

sysCRdnRecMode

Recovery Mode. This object determines if after recovery
of the failed Primary card/port it will become on-line again or not:
auto - automatic . In this case, the failed card/port will become
on-line again after reco…

Enumerationr/w

Enumerated Values:

1	unknown
2	empty
10	psAC
11	psDC
18	gCl1
19	gCl2
20	dCl
21	kCl
22	dcl2
23	dcl2Eth
24	kClEth
25	dcl3
26	dcl3Eth
28	d4T1
29	d8T1
30	dT1DSU
31	dT1CSU
32	dE1DSU
33	dE1LTU
34	dE1aDSU
35	dE1aLTU
36	dT1F
37	dE1F
38	d4E1
39	d8E1
40	dE1Hdsl
41	dT1Hdsl
42	dE1HdslS
43	dT1HdslS
44	d16gsdsl
45	d8sl
46	d4slStuC
47	d4slStuR
50	kML1
51	kML2
52	kML3
53	kML4
54	kML5
55	kML6
56	kML7
57	kML8
59	kML10
60	kMLF
61	kML10New
62	kML11RJ45
63	kML11FO
70	kLS1
71	kLS1New
72	kLS2
80	kTRE
81	kMBE
82	kMBENew
83	fLAN
90	kai
91	kdi
92	kdiCH
100	dHS2
101	d8U
102	d16U
103	d4HS
104	d8HS
110	kHS1
111	kHS2
112	kHSU1
113	kHSU2
114	kHS703
130	kVC1EM
131	kVC1FXO
132	kVC1FXS
133	kVC1MEM
134	kVC1MFXO
135	kVC1MFXS
136	kVC1MFXSW
137	kVC2EM
138	kVC2FXO
139	kVC2FXS
140	kVC2s1EM
141	kVC2s1FXO
142	kVC2s1FXS
143	kVC3EM
144	kVC3FXO
145	kVC3FXS
146	kVC3S0
170	kVF1EM
171	kVF1FXO
172	kVF1FXS
173	kVF3EM
174	kVF3FXO
175	kVF3FXS
176	kVF4EM
177	kVF4FXO
178	kVF4FXS
179	kVF4FXSW
180	kVF4S0
181	kVF5PbxE1
182	kVF5E1PbxSlave
183	kVF5PbxT1
184	kVF5T1PbxSlave
185	kVF5PbxE1New
186	kVF5E1PbxSlaveNew
187	kVF5PbxT1New
188	kVF5T1PbxSlaveNew
189	kVF4FXO3
190	kVF4FXS3
191	kVF4NS0
192	kVF6E1s16
193	kVF6E1s31
194	kVF6T1s12
195	kVF6T1s24
196	kVF8EM
197	kVF8FXO
198	kVF8FXS
200	dimETUR
201	dimV35
202	dimRS422
203	dimRS530
204	dimHssi
205	dimX21
206	dim10BaseT
207	dimE1
208	dim100
209	dt3G747
210	dt3
211	dt3f
212	de3
213	de3f
214	dstm1s1
215	dstm1s2
216	fstm1
217	dstm1
218	dstm1R
219	f2stm1
220	gstm1
221	goc3
222	gstm1D
223	goc3D
270	serverE1
271	serverT1
272	serverE1Pw
273	serverT1Pw
280	gigabitEth
281	gigabitEth2
282	eth2
283	gigabitEth8
284	eth8
290	channelizedT3Pw1
300	cesT128
301	cesE128
302	cesT1Pw28
303	cesE1Pw28
310	vmxE1VeDe
311	vmxE1VeDi
312	vmxE1ViDe
313	vmxE1ViDi
314	vmxT1VeDe
315	vmxT1VeDi
316	vmxT1ViDe
317	vmxT1ViDi
318	vc12E1UeNe
319	vc12E1UeNi
320	vc12E1UiNe
321	vc12E1UiNi
322	vc12T1UeNe
323	vc12T1UeNi
324	vc12T1UiNe
325	vc12T1UiNi
326	vca16E1UeNe
327	vca16E1UeNi
328	vca16E1UiNe
329	vca16E1UiNi
330	vca16T1UeNe
331	vca16T1UeNi
332	vca16T1UiNe
333	vca16T1UiNi
334	vca12E1UeNe
335	vca12E1UeNi
336	vca12E1UiNe
337	vca12E1UiNi
338	vca12T1UeNe
339	vca12T1UeNi
340	vca12T1UiNe
341	vca12T1UiNi
342	vmg16E1Ue
343	vmg16E1Ui
344	vmg16T1Ue
345	vmg16T1Ui
346	vmg12E1Ue
347	vmg12E1Ui
348	vmg12T1Ue
349	vmg12T1Ui

.1.3.6.1.4.1.164.3.3.1.6.3.1.7

sysCRdnRecTime

Redundancy Recovery Time (sec). After switching to the current
online card, the next switch can be performed only after a
minimum time, indicated by this object.
Valid Values: 0..300, 65535.
65535=NA.
This object …

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.6.3.1.8

sysCRdnHwSwFlip

HW or SW decision for Redundancy Flip.
This object is applicable only for sysCRdnMode=singleSlotProtection.
HW - decision is by I/O card
SW - decision is by CL SW.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.1.6.3.1.9

sysCRdnRowStatus

This parameter allows NMS to create/delete entries of this table.
The possible supported RowStatus values are
active (1) and destroy (6).

For Vmux-2100 the supported values are:
active (1), createAndGo (4…

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.3.3.1.6.3.1.10

sysCRdnOnline

Status - who is the Online (current) Redundancy Slot/Port.
This object shows only the Online Slot/Port regarding the Redundancy.
mdlSActivity or prtGenActiveStatus of the same Slot/Port may be Offline.

Enumeration

.1.3.6.1.4.1.164.3.3.1.6.3.1.11

sysCRdnSwitchingMode

This object defines which Self Healing Ring (SHR) SDH ring is used:
Uni Directional or BiDirectional. The type of the ring
is defined according to the direction of traffic flow under
normal working conditions.
…

Enumerationr/w

.1.3.6.1.4.1.164.3.3.1.6.3.1.12

sysCRdnFlipUponEvent

This object allows user to define if Flip to the other port will
be performed (or not), for certain possible events.
Each event is represented by a bit. The value of the object is a sum
of 2**n, according to the bits ha…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.6.3.1.13

sysCRdnLosOrLofTime

This parameter determines how much time to wait before switching,
after LOF or LOS are detected on the TDM Line.
For Ipmux time is counted in msec.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	psA
2	psB
3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
17	io13
18	io14
19	io15
20	psC
101	kmxPsA
102	kmxPsB
103	kmxMlA
104	kmxMlB
105	kmxCl
106	kmxOpt
107	kmxIO1
108	kmxIO2
109	kmxIO3
110	kmxIO4
111	kmxIO5
112	kmxIO6
113	kmxIO7
114	kmxIO8
115	kmxIO9
116	kmxIO10
117	kmxIO11
118	kmxIO12

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.6.3.1.14

sysCRdnEventsTimeWindow

This parameter determines the time window in which
to count events to trigger protection switching.
For Ipmux time is counted in seconds.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.6.3.1.15

sysCRdnSequenceNumberThreshold

This parameter determines the number of Sequence Number errors
that should occur in the time window in order to cause switching.

SNMPv2-SMIInteger32r/w

Enumerated Values:

3	event
4	minor
5	major
6	warning
7	critical

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.6.3.1.16

sysCRdnBufferErrorsThreshold

This parameter determines the number of Buffer undeflow/ overflow events
occured in the time window that cause switching.

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.6.3.1.17

sysCRdnBuffUnderrunTime

This parameter determines how much time to wait before switching,
after jitter buffer underrun.
Switching occurs if no frame arrives within that time.
For Ipmux time is counted in msec.

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.1.6.3.1.18

sysCRdnPrimePriority

The Primary port priority.

In ETX2xx/2xxA:
When selecting sysCRdnMode = manual (10),
this parameter determines the forced active port:
low - means that the secondary port is selected to be active
…

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.3.1.6.3.1.19

sysCRdnSecPriority

The Secondary port priority.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.1.6.3.1.20

sysCRdnWTR

Redundancy Wait to Restore (sec).
Valid Values: 0..999, 65535.
65535=NA.
When the value <> 65535, the value of sysCRdnRecTime must be 65535.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.3.1.6.3.1.21

sysCRdnName

A textual name for the redundancy group.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.3.3.1.6.3.1.22

sysCRdnTxDownDurationUponFlip

This object defines the duration (in seconds) the active
port transmission is shut down after flip occurs.
The transmission is shut down and then opened again (after the duration
defined by this object), in order t…

Unsigned32r/w

Enumerated Values:

1	psA
2	psB
3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
17	io13
18	io14
19	io15
20	psC
101	kmxPsA
102	kmxPsB
103	kmxMlA
104	kmxMlB
105	kmxCl
106	kmxOpt
107	kmxIO1
108	kmxIO2
109	kmxIO3
110	kmxIO4
111	kmxIO5
112	kmxIO6
113	kmxIO7
114	kmxIO8
115	kmxIO9
116	kmxIO10
117	kmxIO11
118	kmxIO12

.1.3.6.1.4.1.164.3.3.1.6.3.1.23

sysDbaseFlipTable

table

.1.3.6.1.4.1.164.3.3.1.7.4 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sysDbaseFlipTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sysDbaseFlipTable'

Dbase Flip time and activation for every configuration.

sysDbaseFlipEntry row .1.3.6.1.4.1.164.3.3.1.7.4.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

sysDbaseFlipIdx

This attribute indicates the Idx of the Cnfg being
the target Configuration.

Integer32

.1.3.6.1.4.1.164.3.3.1.7.4.1.1

sysDbaseFlipTime

This attribute indicates the time (HH:MM) when this data
base will start being used by the Tmp config.

OctetStringr/w

Enumerated Values:

3	clA
4	clB

.1.3.6.1.4.1.164.3.3.1.7.4.1.2

sysDbaseFlipActivation

This attribute indicates if the Dbase flip will be
activated at the time specified for this configuration
(enable) or not (disable).
No more than one flip should be enabled for the same time.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.1.7.4.1.3

mdlSTable

table

.1.3.6.1.4.1.164.3.3.2.1.1 · 1 row entry · 18 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlSTable'

A table.

mdlSEntry row .1.3.6.1.4.1.164.3.3.2.1.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

mdlSSltIdx

A unique number to identify a slot position in the DACS.
The Kilomux should use enumerated values starting with kmx.
For IPmux100 use values 1-13, 20.

Enumeration

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.3.2.1.1.1.1

mdlSCardType

This attribute indicates the type of the card installed
in the specific slot position.
Only PS's are possible in the PS slots.
Only CL's are possible in the CL slots.
Only IO modules are possible in the IO slots.
Kmux …

Enumeration

.1.3.6.1.4.1.164.3.3.2.1.1.1.2

mdlSHwVer

This attribute indicates the Hardware version of the
card installed in the specific slot position.

OctetString

.1.3.6.1.4.1.164.3.3.2.1.1.1.3

mdlSSwVer

This attribute indicates the Software version of the
card installed in the specific slot position.

OctetString

Enumerated Values:

1	psA
2	psB

.1.3.6.1.4.1.164.3.3.2.1.1.1.4

mdlSAlarmStatus

Indicates the current alarm state only for card level.
This object will be set to:
- critical(7): when there is at least one active (ON) critical
alarm .
- major (3): when there is no active critical alar…

Enumeration

Enumerated Values:

1	notActive
2	active

.1.3.6.1.4.1.164.3.3.2.1.1.1.5

mdlSAlarmStatusAll

Indicates the current card alarm state including the
lower level: card, port.
This object will be set to:
- critical(7): when there is at least one active (ON) critical
alarm .
- major (3): when there i…

Enumeration

Enumerated Values:

1	ok
2	f12V
3	f5V

.1.3.6.1.4.1.164.3.3.2.1.1.1.6

mdlSTestStatus

This attribute will be on(3) when there is at least
one test running on a port of the module; otherwise the value
will be off(2).

Enumeration

.1.3.6.1.4.1.164.3.3.2.1.1.1.7

mdlSHwStatus

This attribute will be fail(2) when a HW FAIL exists
on this module (discovered by periodic self test);
otherwise the value will be ok(3).

Enumeration

.1.3.6.1.4.1.164.3.3.2.1.1.1.8

mdlSActivity

notApplicable - when the slot is empty (no module)
offline(1) - when the module is not active (redundant)
online (2) - when the module is active .

Enumeration

.1.3.6.1.4.1.164.3.3.2.1.1.1.9

mdlSAlrClearCmd

Setting this attribute to ON, will enforce a clear
operation on the card level alarms . Upon completion,
the value will automatically change to off(2).

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
17	io13
18	io14
19	io15
103	kmxMlA
104	kmxMlB
105	kmxCl
106	kmxOpt
107	kmxIO1
108	kmxIO2
109	kmxIO3
110	kmxIO4
111	kmxIO5
112	kmxIO6
113	kmxIO7
114	kmxIO8
115	kmxIO9
116	kmxIO10
117	kmxIO11
118	kmxIO12
255	standAlone

.1.3.6.1.4.1.164.3.3.2.1.1.1.10

mdlSAlrClearAllCmd

Setting this attribute to ON, will enforce a clear
operation on card and port level alarms . Upon completion,
the value will automatically change to off(2).

Enumerationr/w

Enumerated Values:

2	external
3	internal

.1.3.6.1.4.1.164.3.3.2.1.1.1.11

mdlSAlrMaskAll

on(3) - will cause masking of all the card level alarms.
These alarms will not be sent to NMS and will not
be taken into account for Alarms Status.
off(2) - will unmask all card level alarms except those
masked via t…

Enumerationr/w

.1.3.6.1.4.1.164.3.3.2.1.1.1.12

mdlSCmd

General object for any special command at card level.
0=NotApplicable, for cards that don't support this object.

For KML.10(ISDN) card of KM-2100, the object will indicate
Manual Call Command in Switch …

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	unknown
2	notUsed
3	offLine
4	onLine
5	offLineRedundancy
6	onLineRedundancy

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.2.1.1.1.13

mdlSReset

Reset action to be performed on the module.

Enumerationr/w

Enumerated Values:

2	off
3	major
4	minor
5	event
6	warning
7	critical

.1.3.6.1.4.1.164.3.3.2.1.1.1.14

mdlSRebuildFrame

Applicable only for KiloMux Main Link cards only.
'2' = off, this will be always the Get value.
'3' = on, this is the Set command used to Rebuild the Frame.
Upon completing the operation, the value will automatically …

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.3.2.1.1.1.15

mdlSBackupSwVer

This attribute indicates the Backup Software version of the
card installed in the specific slot position.

OctetString

.1.3.6.1.4.1.164.3.3.2.1.1.1.16

mdlSSecondaryBackupSwVer

This attribute indicates the Secondary Backup Software version of the
card installed in the specific slot position.

OctetString

.1.3.6.1.4.1.164.3.3.2.1.1.1.17

mdlSPiggybackVer

This attribute indicates the Piggyback version of the
card installed in the specific slot position.

OctetString

.1.3.6.1.4.1.164.3.3.2.1.1.1.18

mdlCTable

table

.1.3.6.1.4.1.164.3.3.2.1.2 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlCTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlCTable'

A table.

mdlCEntry row .1.3.6.1.4.1.164.3.3.2.1.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

mdlCConfigIdx

This object indicates the Configuration number (1..255)
referred.
Value of 255 specifies the TmpCnfg (Scratch).

Integer32

Enumerated Values:

1	noOp
2	off
3	on

.1.3.6.1.4.1.164.3.3.2.1.2.1.1

mdlCSlotIdx

This object indicates a unique number of the slot position
in which the module is inserted.
The Kilomux should use enumerated values starting with kmx.

Enumeration

Enumerated Values:

1	noOp
2	off
3	on

.1.3.6.1.4.1.164.3.3.2.1.2.1.2

mdlCProgCardType

This object indicates the card type assigned to the specific
slot in the common configuration.
This object is identical for all the configurations (1..255).
Only the TmpCnf(255) might have a different value.
The write…

Enumerationr/w

.1.3.6.1.4.1.164.3.3.2.1.2.1.3

mdlCNoOfExtPrt

Number of external ports in the programmed module of
the specific slot position

SNMPv2-SMIInteger32

Enumerated Values:

1	none
2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.2.1.2.1.4

mdlCNoOfIntPrt

Number of internal ports in the programmed module of
the specific slot position.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.2.1.2.1.5

mdlCParam

General configuration object at card level (per configuration).
NotApplicable=0, for cards that don't support this object.

For D8U and D16U cards of DXC, the object will indicate
the port on which BERT …

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.2.1.2.1.6

mdlAlrTable

table

.1.3.6.1.4.1.164.3.3.2.1.3.1 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlAlrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlAlrTable'

The list of card alarms.

mdlAlrEntry row .1.3.6.1.4.1.164.3.3.2.1.3.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

mdlAlrIdx

A unique number to identify an entry in the alarm status
table.
Users should use the get next function to read this table
because the indexes are not consecutive

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.2.1.3.1.1.1

mdlAlrSltIdx

This attribute indicates the desired slot position.
The Kilomux should use enumerated values starting with kmx.

Enumeration

.1.3.6.1.4.1.164.3.3.2.1.3.1.1.2

mdlAlrCode

This object indicates a code related to a specific
alarm description. The list of codes and their related
descriptions will be sent to NMS request (for display purpose)
by alrGenTable.

SNMPv2-SMIInteger32

Enumerated Values:

1	localLoop
2	remoteLoop
3	bert
4	plb
5	rlb
6	llb
7	toneInjection
8	txInband
9	rxInband
10	remLoopOnRemUnit
11	bertOnRemUnit
12	llbOnRemUnit
14	txPlb
15	txLlb
16	dteLoop
20	hdslTxInband
21	hdslRxInband
22	monitor
23	userLineLoopback
26	lbbd
27	lb1
28	lb2
30	tsRemoteLoop
32	downstreamAis
33	upstreamAis
34	sendRdi

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.2.1.3.1.1.3

mdlAlrState

This object indicates the card alarm severity.

Enumeration

.1.3.6.1.4.1.164.3.3.2.1.3.1.1.4

mdlAlarmMask

Alarm Mask is : on/off.

Enumeration

.1.3.6.1.4.1.164.3.3.2.1.3.1.1.5

mdlAlarmInvert

Alarm Invert is : on/off.

Enumeration

.1.3.6.1.4.1.164.3.3.2.1.3.1.1.6

mdlAlarmOnOff

Alarm state is : on/off.

Enumeration

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.3.2.1.3.1.1.7

mdlAlarmCounter

A counter - how many times the alarm occured (ON) since last
clear operation or since last Reset.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.2.1.3.1.1.8

mdlAlrMaskTable

table

.1.3.6.1.4.1.164.3.3.2.1.3.2 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlAlrMaskTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlAlrMaskTable'

The list of card masked alarms.

mdlAlrMaskEntry row .1.3.6.1.4.1.164.3.3.2.1.3.2.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
mdlAlrMaskSltIdx This attribute indicates the desired slot position. The Kilomux should use enumerated values starting with kmx.	Enumeration	`.1.3.6.1.4.1.164.3.3.2.1.3.2.1.1`
mdlAlrMask This object is a mask that indicates which card level alarms are masked. The masked alarms (their bit is set to '1') are neither sent to the manager, nor taken into account for alarm status and LEDs. Bit no. = Alarm c…	OctetStringr/w	`.1.3.6.1.4.1.164.3.3.2.1.3.2.1.2`

mdlClTable

table

.1.3.6.1.4.1.164.3.3.2.2.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlClTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlClTable'

A table.

mdlClEntry row .1.3.6.1.4.1.164.3.3.2.2.1.1

An entry in table.

Indexes

prtSAlarmPrtIdx prtSAlarmIdx

Column Syntax OID

mdlClIdx

This object indicates the Cl slot referred.

Enumeration

.1.3.6.1.4.1.164.3.3.2.2.1.1.1

mdlClSwchStatus

This object indicates the status of the switches on
the referred DCL card.
Each switch is represented by a bit. The status is a sum
of 2**n, according to the bits. There are 4 switches:
bit 0 SP-PAR (LSB) '1' - Defau…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.2.2.1.1.2

mdlClLastFlipDate

Date when last flip occured.
The format would be as specified by the sysSDateFormat.

OctetString

.1.3.6.1.4.1.164.3.3.2.2.1.1.3

mdlClLastFlipTime

Time when last flip occured.

OctetString

Enumerated Values:

3	event
4	minor
5	major
6	warning
7	critical

.1.3.6.1.4.1.164.3.3.2.2.1.1.4

mdlClLastFlipCause

The cause of last flip.

OctetString

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.3.2.2.1.1.5

mdlPsTable

table

.1.3.6.1.4.1.164.3.3.2.3.1 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlPsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlPsTable'

A table.

mdlPsEntry row .1.3.6.1.4.1.164.3.3.2.3.1.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
mdlPsIdx This object indicates the PS card referred.	Enumeration	`.1.3.6.1.4.1.164.3.3.2.3.1.1.1`
mdlPsStatus This object indicates the status of the PS card.	Enumeration	`.1.3.6.1.4.1.164.3.3.2.3.1.1.2`
mdlPsTestResult This object indicates the result of the PS card test. ok (1) - the test passed successfully. f12V (2) - 12V FAIL was detected f5V (3) - 5V FAIL was detected.	Enumeration	`.1.3.6.1.4.1.164.3.3.2.3.1.1.3`

prtGenParamTable

table

.1.3.6.1.4.1.164.3.3.3.1.1 · 1 row entry · 19 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtGenParamTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtGenParamTable'

A table.

prtGenEntry row .1.3.6.1.4.1.164.3.3.3.1.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtGenPrtIdx

This attribute indicates a unique number to identify a port.
The valid port number depends on the IO slot no., the
installed card type and the port type: outside/external, inside/internal.

In the Kilo…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.1.1.1

prtGenSlt

This attribute indicates a unique number to identify the slot where
the card is inserted in.
When the unit is stand-alone, this object is not applicable
and 255 will be used.
The Kilomux should use the enumerated starti…

Enumeration

.1.3.6.1.4.1.164.3.3.3.1.1.1.2

prtGenExtInt

This attribute describes the type of the designated port.
Exteral port is a port with a physical connector. Internal
port might be of two types, one is a composite port which
collects data of a few external ports i…

Enumeration

.1.3.6.1.4.1.164.3.3.3.1.1.1.3

prtGenIfIndex

SNMPv2-SMIInteger32

Enumerated Values:

1	p2E3m1
2	p2E4m1
3	p2E5m1
4	p2E6m1
5	p2E7m1
6	p511
7	p2E10m1
8	p2047
9	p2E15m1
10	p2E17m1
11	p2E18m1
12	p2E20m1
13	qrss
14	p2E21m1
15	p2E22m1
16	p2E23m1
17	p2E25m1
18	p2E28m1
19	p2E29m1
20	p2E31m1
21	p2E32m1
22	rj011
23	p63
24	p1M7S
25	p1S7M
26	alternate
27	mark
28	space
29	p2E11m1
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.1.1.4

prtGenActiveStatus

This attribute describes the activity status of the port.
unknown(1) indicates that the information is not supported.
notUsed(2) indicates that the port is not connected according
to the active config.
offLin…

Enumeration

Enumerated Values:

1	noError
2	r10Em1
3	r10Em2
4	r10Em3
5	r10Em4
6	r10Em5
7	r10Em6
8	r10Em7
9	single
255	notApplicable

.1.3.6.1.4.1.164.3.3.3.1.1.1.5

prtGenAlrStatus

Indicates the alarm state at port (ch) agent level.
This object will be:
- critical(7): when there is at least one active (ON) critical
alarm .
- major (3): when there is no active critical alarm, but the…

Enumeration

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.3.3.1.1.1.6

prtGenTestStatus

This attribute will be on(3) when there is at least one test
in progress (running) on the port; otherwise the value will
be off(2).

Enumeration

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.3.3.1.1.1.7

prtGenTestMask

This is a mask which indicates which tests from the
'prtGenTestCmd' list are allowed for the selected port.
If a specific test is allowed, its respective bit will be SET
in the mask :

TEST …

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.1.1.8

prtGenTestCmd

Setting this object to a value as detailed furter on
(except 0) will initiate a test on the specific port,
if the operation is allowed (according to TestMask).
If the operation is not allowed, the mux will ignore the…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.1.1.9

prtGenTestRunning

This object indicates which tests are running currently on
the selected port (initiated by user and/or by the system).
If a specific test is currently running on the port, its
respective bit will be SET:
…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.1.1.10

prtGenType

This object describes the type of the selected port.
idsl - applicable for external ports of HS-U cards (of DXC) when
interface is LT-1.

Enumeration

.1.3.6.1.4.1.164.3.3.3.1.1.1.11

prtGenInterfaceType

This attribute indicates a unique HW interface type of the
selected port.
Examples:
- for T1 cards: DSU, CSU
- for E1 cards: DSU, LTU
- for HS cards: v35, rs422, x21
etc...

OctetString

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.3.3.1.1.1.12

prtGenAlrClearCmd

Setting this attribute to ON, will enforce a clear
operation on the port level alarms . Upon completion,
the value will automatically change to off(2).
noOp - will be used by agents that do not support this
f…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	syncLoss
3	sync

.1.3.6.1.4.1.164.3.3.3.1.1.1.13

prtGenAlrMaskAll

on(3) - will mask all the alarms of the selected port
off(2)- will unmask all alarms of the selected port except
the ones selected by the prtAlrMaskTable.
noOp - will be used by agents that do not support this
…

Enumerationr/w

Constraints:
range: 0-4

.1.3.6.1.4.1.164.3.3.3.1.1.1.14

prtGenParamStatus

This object indicates Status of parameters specific to the
selected port.
- For a port that has no special status or is supported
by prtSExHsfStatTable - 1 Octet: 00hex

- For HS cards (Dxc cards) - 1 o…

OctetString

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.3.3.1.1.1.15

prtGenRdnStatus

This object indicates if this port is part of a redundant pair and in
this case, if it is On or Off.

none(1) - No redundancy or Not Applicable
off (2) - the port is part of a redundant pair and it is …

Enumeration

.1.3.6.1.4.1.164.3.3.3.1.1.1.16

prtGenTestMaskXP

This is an Expanded test mask of the prtGenTestMask object.
The prtGenTestMask object reached its maximum, being an Integer with 31 bits.
This object indicates which tests from the 'prtGenTestCmdXP' list are
allowed f…

OctetString

.1.3.6.1.4.1.164.3.3.3.1.1.1.17

prtGenTestCmdXP

This is an Expanded test command of the prtGenTestCmd object.
The prtGenTestCmd object reached its maximum, being an Integer with 31 bits.
Setting this object to a value as detailed furter on
(except 0) will initiate a…

OctetStringr/w

.1.3.6.1.4.1.164.3.3.3.1.1.1.18

prtGenTestRunningXP

This is an Expanded object of the prtGenTestRunning object.
The prtGenTestRunning object reached its maximum, being an Integer with 31 bits.
This object indicates which tests are running currently on
the selected port …

OctetString

.1.3.6.1.4.1.164.3.3.3.1.1.1.19

prtGenTestDurationTable

table

.1.3.6.1.4.1.164.3.3.3.1.2 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtGenTestDurationTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtGenTestDurationTable'

A table.

prtGenTestDurationEntry row .1.3.6.1.4.1.164.3.3.3.1.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtGenTestPrtIdx

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.2.1.1

prtGenTestIdx

This attribute indicates the test, the duration refers.

Enumeration

Enumerated Values:

1	notApplicable
2	disabled
3	enabled

.1.3.6.1.4.1.164.3.3.3.1.2.1.2

prtGenTestDuration

This attribute indicates the maximum duration of executing
a test on the specific port. This entry applies to the
specified test . The resolution will be a minute, and the
maximum duration is limited to 30 minutes .
A z…

SNMPv2-SMIInteger32r/w

Constraints:
range: 0-4

.1.3.6.1.4.1.164.3.3.3.1.2.1.3

prtGenTsTable

table

.1.3.6.1.4.1.164.3.3.3.1.3 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtGenTsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtGenTsTable'

The write operation into the Table's Objects is valid only
for the TmpCnfg entry (Scratch),exept some products 
which enable direct writing to the ActiveCnfg. 
This is written in the respective product's spec.

prtGenTsEntry row .1.3.6.1.4.1.164.3.3.3.1.3.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtGenTsCnfgIdx

This attribute indicates the Idx of the Cnfg(1..255) being
accessed.
Idx of 255 relates to the TmpCnfg.

Integer32

.1.3.6.1.4.1.164.3.3.3.1.3.1.1

prtGenTsPrtIdx

This attribute indicates a unique port number.
The valid port number depends on the IO slot no., the
installed card type and the port type: outside, inside,
SP.
In the DXC :
- first two digits will be: (IO slot numb…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.3.1.2

prtGenTsIdx

This attribute indicates a unique time slot position.
The valid time slots are
1..25 for T1 Card (25=Fbit)
0..31 for E1 or HS Card .
In G732S-E1 lines time slot 16 is not valid for data,
it is dedicated for multifra…

SNMPv2-SMIInteger32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.3.3.1.3.1.3

prtGenTsType

The type of Timeslot.
If the source or destination port is an HS port,'TS Type'
must be 'data'.
nc - means that this TimeSlot is not connected.
voice, data, vcMP - also mean that this TS is connected.
mng - means t…

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.1.3.1.4

prtGenTsIConPrt

This attribute indicates the internally (In Mux)
connected port.
The valid port number depends on the IO slot no., the
installed card type and the port type: outside, inside,
SP.
* The outside ports will be the T1/E…

SNMPv2-SMIInteger32r/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
107	kmxIO1
108	kmxIO2
109	kmxIO3
110	kmxIO4
111	kmxIO5
112	kmxIO6
113	kmxIO7
114	kmxIO8
115	kmxIO9
116	kmxIO10
117	kmxIO11
118	kmxIO12
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.3.1.5

prtGenTsIConTs

This attribute indicates a unique time slot position.
The valid time slots are
1..25 for T1 Card (25=Fbit)
0..31 for E1 (or HS) Card.
In G732S-E1 lines time slot 16 is not valid for data, it is
dedicated for multifr…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
103	kmxMlA
104	kmxMlB

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.3.1.6

prtSAlarmTable

table

.1.3.6.1.4.1.164.3.3.3.1.4.1 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtSAlarmTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtSAlarmTable'

A table.

prtSAlarmEntry row .1.3.6.1.4.1.164.3.3.3.1.4.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtSAlarmIdx

A unique number to identify an entry in the alarm status
table.
Users should use the get next function to read this table
because the indexes are not consecutive.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	disabled
3	enabled

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.4.1.1.1

prtSAlarmPrtIdx

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	rdlLoop
3	userConfig

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.4.1.1.2

prtSAlarmCode

This object indicates a code related to a specific
alarm description. The list of codes and their related
descriptions will be sent to NMS request (for display purpose)
by alrGenTable.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.4.1.1.3

prtSAlarmState

This object indicates the port alarm severity.

Enumeration

.1.3.6.1.4.1.164.3.3.3.1.4.1.1.4

prtSAlarmMask

Alarm Mask is : on/off.

Enumeration

.1.3.6.1.4.1.164.3.3.3.1.4.1.1.5

prtSAlarmInvert

Alarm Invert is : on/off.

Enumeration

.1.3.6.1.4.1.164.3.3.3.1.4.1.1.6

prtSAlarmOnOff

Alarm state is : on/off.

Enumeration

.1.3.6.1.4.1.164.3.3.3.1.4.1.1.7

prtSAlarmCounter

A counter - how many times the alarm occured (ON) since last
clear operation or since last Reset.

SNMPv2-SMIInteger32

Enumerated Values:

3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
17	io13
18	io14
19	io15
255	standAlone

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.4.1.1.8

prtAlrMaskTable

table

.1.3.6.1.4.1.164.3.3.3.1.4.2 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtAlrMaskTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtAlrMaskTable'

A table.

prtAlrMaskEntry row .1.3.6.1.4.1.164.3.3.3.1.4.2.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
prtAlrMaskPrtIdx This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilo…	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.3.3.1.4.2.1.1`
prtAlrMask This object is a mask that indicates which port level alarms are masked. The masked alarms (their bit is set to '1') are neither sent to the manager, nor taken into account for alarm status and LEDs. Bit no. = Alarm c…	OctetStringr/w	`.1.3.6.1.4.1.164.3.3.3.1.4.2.1.2`

prtBertTable

table

.1.3.6.1.4.1.164.3.3.3.1.5 · 1 row entry · 16 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtBertTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtBertTable'

This table includes the BERT parameters, counters and 
commands.
The configurable parameters:
- prtBertPattern
- prtBertInjectRate
- prtBertTs
are not Set per configuration (same for all Configurations)
but start being applied by the Agent only upon successful
Update/Download operation. Therefore, Set will enter the 
values to the Temporary Configuration of the agent, while
Get will get the values of the Active Configuration.

prtBertEntry row .1.3.6.1.4.1.164.3.3.3.1.5.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtBertPrtIdx

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.5.1.1

prtBertPattern

This object indicates the pattern of the BERT.
p2Exxm1 = 2Exx-1.
pxx = pattern xx.
This object is the same for all configurations.
notApplicable - when this object is not supported.

Enumerationr/w

Enumerated Values:

3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
17	io13
18	io14
19	io15
103	kmxMlA
104	kmxMlB
106	kmxOpt
107	kmxIO1
108	kmxIO2
109	kmxIO3
110	kmxIO4
111	kmxIO5
112	kmxIO6
113	kmxIO7
114	kmxIO8
115	kmxIO9
116	kmxIO10
117	kmxIO11
118	kmxIO12
255	standAlone

.1.3.6.1.4.1.164.3.3.3.1.5.1.2

prtBertInjectRate

This object indicates the error rate injection of the BERT.
r10Emx = 10E-x
This object is the same for all configurations.
single - single error injection.
notApplicable - when this object is not supported.

Enumerationr/w

Enumerated Values:

1	other
2	esf
3	d4
4	e1
5	e1Crc
6	e1MF
7	e1CrcMF
8	unframed

.1.3.6.1.4.1.164.3.3.3.1.5.1.3

prtBertInjectErrRateCmd

This object controls activation/deactivation of the Error
Rate Injection during BERT.

Enumerationr/w

Enumerated Values:

1	jbzs
2	b8zs
3	hdb3
4	zbtsi
5	ami
6	other

.1.3.6.1.4.1.164.3.3.3.1.5.1.4

prtBertInjectSingleErrCmd

This object enables to initiate a Single Error Injection
during BERT (on). Upon completion, the value will
automatically change to off(2).

Enumerationr/w

Enumerated Values:

1	none
2	robbedBit
3	bitOriented
4	messageOriented

.1.3.6.1.4.1.164.3.3.3.1.5.1.5

prtBertRunTime

This object indicates how much time (seconds) passed since
BERT started to run.

SNMPv2-SMIInteger32

Enumerated Values:

1	other
2	ansi-T1-403
4	att-54016
8	fdl-none
16	transFdl

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.5.1.6

prtBertESs

How many Errored Seconds were detected since BERT started
to run.
Counter for Kmux and MP.

SNMPv2-SMIInteger32

Enumerated Values:

1	other
2	user
3	carrier
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.5.1.7

prtBertSyncLoss

How many times Sync Loss was detected since BERT started
to run.
For some products: number of seconds in which Sync Loss occured
since BERT started to run. See product specification.

SNMPv2-SMIInteger32

Enumerated Values:

1	other
2	tr62411
3	ccitt
4	fast

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.5.1.8

prtBertErrorBits

How many Error Bits were detected since BERT started
to run.

SNMPv2-SMIInteger32

Enumerated Values:

1	none
2	trans
3	full

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.5.1.9

prtBertClearCounters

Setting this object to ON, will enforce a clear
operation of some BERT Counters. Upon completion,
the value will automatically change to off(2).

Enumerationr/w

Constraints:
range: 0-4

.1.3.6.1.4.1.164.3.3.3.1.5.1.10

prtBertSyncStatus

Sync Status while BERT runs.

Enumeration

Enumerated Values:

2	notsupported
3	forcedIdle
4	forcedBusy
5	busyIdle
6	idleBusy

.1.3.6.1.4.1.164.3.3.3.1.5.1.11

prtBertTs

This object indicates on which TSs of the selected port, BERT
should be applied.
Each Bit of the Octet represents a TS:
31 ......0
MSB LSB

Bit 0 will not be used.
If the bit value is '1' - BERT shou…

OctetStringr/w

Constraints:
range: 0-4

.1.3.6.1.4.1.164.3.3.3.1.5.1.12

prtBertResult

This object indicates Result of BERT
for the selected port
(number of error bits divided to the total
number of data bits.)
Applicable only if BERT is running on this port

Agents that do not support this…

OctetString

Constraints:
range: 0-4

.1.3.6.1.4.1.164.3.3.3.1.5.1.13

prtBertTxBits

How many data bits were transmitted since BERT started
to run, or since last counter clear
(prtBertClearCounters set to on).

SNMPv2-SMIInteger32

Enumerated Values:

1	unknown
2	len0p133ft
3	len134p266ft
4	len267p399ft
5	len400p533ft
6	len534p655ft
7	fcc68

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.5.1.14

prtBertRxBits

How many data bits were Received since BERT started
to run, or since last counter clear
(prtBertClearCounters set to on).

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	txGain0db
3	txGain7dot5db
4	txGain15db
5	txGain22dot5db

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.5.1.15

prtBertTxErrorBits

Number of injected error bits since BERT started
to run, or since last counter clear
(prtBertClearCounters set to on).

SNMPv2-SMIInteger32

Enumerated Values:

2	off
3	fdlOrTs0
4	dedicatedTs
5	dedicatedPpp
6	dedicatedFr
7	internal

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.5.1.16

prtMonTable

table

.1.3.6.1.4.1.164.3.3.3.1.6 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtMonTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtMonTable'

For DXC, the write operation into the Table's Objects is valid only
for the TmpCnfg entry (Scratch).

prtMonEntry row .1.3.6.1.4.1.164.3.3.3.1.6.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtMonCnfgIdx

This object indicates the Idx of the Cnfg(1..255) being
accessed.
Idx of 255 relates to the TmpCnfg.
For products that do not support configurations, 1 will be always used.

Integer32

Enumerated Values:

1	notApplicable
2	none
3	proprietary
4	rip2

.1.3.6.1.4.1.164.3.3.3.1.6.1.1

prtMonitoringIdx

This object indicates the Monitoring Port Index.
For DXC:
The valid port number depends on the IO slot no., the
installed card type and the port type: external, internal.
* The external ports will according to the con…

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	regular
3	transparent

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.6.1.2

prtMonitoringEnable

This object indicates if the prtMonitoringIdx is configured as
a monitoring port or not.
disabled = the port is NOT configured to monitor. Setting this object
to this value will cause reset (to 0) of the…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	br56
3	br64

.1.3.6.1.4.1.164.3.3.3.1.6.1.3

prtMonitoringTSs

This object indicates which TSs of the Monitoring port,
the test equipment should monitor.
Each Bit of the Octet represents a TS:
31 ......0
MSB LSB

Bit 0 will not be used.
If the bit value is '1' -…

OctetStringr/w

Enumerated Values:

1	notApplicable
2	rxGain12dB
3	rxGain30dB
4	rxGain36dB
5	shortHaul
6	longHaul
7	rxGain20dB

.1.3.6.1.4.1.164.3.3.3.1.6.1.4

prtMonitoredPort

This object indicates the MONITORED Port Index that the Monitoring
port monitors.
For DXC:
The valid port number depends on the IO slot no., the
installed card type and the port type: external, internal.
* T…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.6.1.5

prtMonitoredTSs

This object indicates which TSs of the Monitored port, should be monitored.
Each Bit of the Octet represents a TS:
31 ......0
MSB LSB

Bit 0 will not be used.
If the bit value is '1' - this TS should …

OctetStringr/w

Enumerated Values:

1	notApplicable
2	csu
3	dsu
4	ltu

.1.3.6.1.4.1.164.3.3.3.1.6.1.6

prtCfgParamTable

table

.1.3.6.1.4.1.164.3.3.3.1.7.1 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtCfgParamTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtCfgParamTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry.
KMUX parameters are for the cards: KMBE/New, KVF.6 family.

prtCfgParamEntry row .1.3.6.1.4.1.164.3.3.3.1.7.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtCfgParamCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

Enumerated Values:

1	notApplicable
2	noMng
3	mng

.1.3.6.1.4.1.164.3.3.3.1.7.1.1.1

prtCfgParamIdx

A unique identifier of the port (within the card when applicable).
- For KM-2100: Slot*100+Ch
external ports: Ch=1..10
internal ports (sub-channels): Ch=11..20.
- For FCD-T1/E1(L): MAIN=111, SUB=113, CH1=122, CH2=…

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.1.7.1.1.2

prtCfgParamSlt

This attribute indicates a unique number to identify the slot where
the card is inserted in.
In the 2104 Unit the entries kmxIO5(111)..kmxIO12(118) are not valid.
notApplicable(255) - for products that do not have Slots.

Enumeration

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.3.3.1.7.1.1.3

prtCfgParamOperatedMl

The main link for this channel.
The field is relevant only for ML modes of Dual, Priority
Bumping and Switched Backup.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.1.7.1.1.4

prtCfgParamMlAtoMlBPrio

ML-A to ML-B Priority.
The field is relevant only for ML modes of Priority Bumping
and Switched Backup.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disabled
3	enabled

.1.3.6.1.4.1.164.3.3.3.1.7.1.1.5

prtCfgParamMlBtoMlAPrio

ML-B to ML-A Priority.
The field is relevant only for ML modes of Priority Bumping.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	sub
3	main

.1.3.6.1.4.1.164.3.3.3.1.7.1.1.6

prtCfgParamInbandLoopDetection

Inband Loop Detection.
The field is relevant for FCD-T1/E1(L) ports.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.3.3.1.7.1.1.7

prtCfgParamInbandLoopPatternCfg

This object indicates if Inband Loop polynomial pattern
will be according to RDL Loop (the standard) or User Configurated
according to prtCfgParamInbandLoopActPattern and
prtCfgParamInbandLoopDeactPattern.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.1.7.1.1.8

prtCfgParamInbandLoopActPattern

This object is a binary string of up to 8 bits.
Though the syntax allows for any ASCII characters, for this object
only '0' or '1' characters are valid.
The string determines coefficients of the polynomial pattern
sent …

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.3.3.1.7.1.1.9

prtCfgParamInbandLoopDeactPattern

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.3.3.1.7.1.1.10

prtT1E1StatTable

table

.1.3.6.1.4.1.164.3.3.3.2.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtT1E1StatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtT1E1StatTable'

T1/E1 port statistics table.

prtT1E1StatEntry row .1.3.6.1.4.1.164.3.3.3.2.1.1

An entry in the T1/E1 port statistics table.

Indexes

No indexes recorded

Column	Syntax	OID
prtT1E1SPrtIdx This attribute indicates a unique port number. The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The outside port…	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.3.3.2.1.1.1`
prtT1E1SSlt This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used.	Enumeration	`.1.3.6.1.4.1.164.3.3.3.2.1.1.2`
prtT1E1OosCount This object is applicable only for an E1 active port. It provides the number of red alarm events since the last count clearing.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.3.3.2.1.1.3`
prtT1E1BpvLastMin This object is applicable only for an E1 active port. It provides the number of BPV (BiPolar Violation) events detected during the last minute.	SNMPv2-SMIGauge32 Constraints: `range: 1-255`	`.1.3.6.1.4.1.164.3.3.3.2.1.1.4`
prtT1E1BpvMax This object is applicable only for an E1 active port. It provides the maximal number of BPV (BiPolar Violation) events (per minute), detected during the worst minute.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.3.3.3.2.1.1.5`

prtT1E1CnfgTable

table

.1.3.6.1.4.1.164.3.3.3.2.2 · 1 row entry · 34 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtT1E1CnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtT1E1CnfgTable'

T1/E1 port configuration table.

prtT1E1CnfgEntry row .1.3.6.1.4.1.164.3.3.3.2.2.1

An entry in the T1/E1 port configuration table.

Indexes

No indexes recorded

Column Syntax OID

prtT1E1CnfgIdx

This attribute indicates the Idx of the Config being accessed.
Idx of 255 relates to the Temporary (Scratch) Config.

Integer32

Enumerated Values:

1	auto
2	b32bit
3	b60bit
4	b104bit
5	b144bit
255	notApplicable

.1.3.6.1.4.1.164.3.3.3.2.2.1.1

prtT1E1PrtIdx

This attribute indicates a unique port number.
The same numbering as for prtGenPrtIdx.
The valid port number depends on the IO slot no., the
installed card type and the port type: outside, inside.
In the DX…

SNMPv2-SMIInteger32

Enumerated Values:

1	dce
2	dte1
3	dte2
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.2.2.1.2

prtT1E1Slt

This attribute indicates a unique number to identify the slot where
the card is inserted in.
When the unit is stand-alone, this object is not applicable
and 255 will be used.

Enumeration

Enumerated Values:

1	on
2	rts
255	notApplicable

.1.3.6.1.4.1.164.3.3.3.2.2.1.3

prtT1E1LineType

This variable indicates the variety of T1/E1
Line implementing this circuit. The type of
circuit affects the number of bits per second
that the circuit can reasonably carry, as well
as the interpretation of th…

Enumerationr/w

Enumerated Values:

2	off
3	on
255	notApplicable

.1.3.6.1.4.1.164.3.3.3.2.2.1.4

prtT1E1LineCode

This variable describes the variety of Zero
Code Suppression used on the link, which in
turn affects a number of its characteristics.

jbzs=b7zs refers the Jammed Bit Zero Suppres-
sion, in whi…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disabled
3	enabled

.1.3.6.1.4.1.164.3.3.3.2.2.1.5

prtT1E1SignalMode

'none' indicates that no bits are reserved for
signaling on this channel.

'robbedBit' indicates that T1 Robbed Bit Signaling is in use.

'bitOriented' indicates that E1 Channel Associated
…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	rdlLoop
3	userConfig

.1.3.6.1.4.1.164.3.3.3.2.2.1.6

prtT1E1Fdl

This bitmap describes the use of the facili-
ties data link, and is the sum of the capabili-
ties:

'other' indicates that a protocol other than
one following is used.

'ansi-T1-403' ref…

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.2.2.1.7

prtT1E1FdlMode

Fdl Mode of the T1 selected port.
notApplicable - will be used for an E1 port.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.2.2.1.8

prtT1E1Sync

This object enables returning to normal operation, after
the end of a main/sub link red alarm event, in reduced time.
'tr62411' - complies with AT&T TR-62411 (after 10 seconds).
Applicable for both T1 and E…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	linkOK
3	on

.1.3.6.1.4.1.164.3.3.3.2.2.1.9

prtT1E1CGA

This object selects the method used to signal the CGA state
to the other end, through the main/sub link.
'none' - non-transparent mode. When one of the links
(main/sub) will be in Out Of Service state, both…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	normal
3	invert

.1.3.6.1.4.1.164.3.3.3.2.2.1.10

prtT1E1IdleCode

This object selects the code transmitted to fill idle
(unused) time slots in the main link frame.
Valid range: (0 - FF HEX) .

OctetStringr/w

Enumerated Values:

1	notApplicable
2	rs530
3	v35
4	rs422
5	x21
6	v24
7	rs530a
8	rs232
9	rs449

.1.3.6.1.4.1.164.3.3.3.2.2.1.11

prtT1E1OosSignal

Enumerationr/w

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.3.3.2.2.1.12

prtT1E1VoiceOos

Voice Out-Of-Service code. Valid range: (0 - FF HEX).
For agents that do not support this feature, the value will
always be 0.

OctetStringr/w

.1.3.6.1.4.1.164.3.3.3.2.2.1.13

prtT1E1DataOos

Data Out-Of-Service code. Valid range: (0 - FF HEX).
For agents that do not support this feature, the value will
always be 0.

OctetStringr/w

.1.3.6.1.4.1.164.3.3.3.2.2.1.14

prtT1E1LineLengthMask

This attribute is the line length mask parameter used only
for T1/DSU interfaces.
len400p533ft=length range: 400ft to 533ft
'fcc68' - provides compliance with the FCC 68.308 Option A
output pulse mask.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.2.2.1.15

prtT1E1TxGainMask

This attribute is the tx gain mask parameter (dB), used
only for T1/CSU interfaces.

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
17	io13
18	io14
19	io15
255	standAlone

.1.3.6.1.4.1.164.3.3.3.2.2.1.16

prtT1E1InbandMng

A unique number to identify an Inband management over the
link.
internal - supported by KM-2100 only. It means that the management is internal
to the frame. It takes part of the ML Frame bits (instead of dat…

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.3.3.2.2.1.17

prtT1E1InbandMngRate

A unique number to identify the rate of the Inband management.
It is required only for E1 links and is applicable only when
prtExT1E1InbandMng selected is FdlOrTs0 or dedicatedTs.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.2.2.1.18

prtT1E1DedicatedTs

The value is differently determined for different products.
There are two methods:

1) A unique number to identify Dedicated TS of the T1/E1 port.
It is applicable only when prtExT1E1InbandMng selected …

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.2.2.1.19

prtT1E1InbandMngRoutProt

Inband Mng Routing Protocol of the port.
When prtT1E1InbandMng is 'dedicatedPpp'-'proprietary' and
'rip2' are applicable.
For other values - only 'proprietary' is applicable.
…

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.2.2.1.20

prtT1E1LinkMode

regular - TSs are connected by user via TS Assignment only
transparent - when a port with this Link Mode is connected to an
internal T1/E1 port of a T3/E3 card, TS0, TS16 and Fbit
are transp…

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.3.3.2.2.1.21

prtT1E1Multiplier

The data rate of each TS. The multiplier values
can be 56 kbps or 64 kbps. For T1 only.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.2.2.1.22

prtT1E1RxGain

This attribute is the rx volume (dB).

Enumerationr/w

Enumerated Values:

1	unknown
2	noUse
3	nmsSlip
4	nmsPpp
5	muxSlip
6	muxPpp
7	terminal
8	dialOut

.1.3.6.1.4.1.164.3.3.3.2.2.1.23

prtT1E1RAI

Remote Alarm Signal

Enumerationr/w

Enumerated Values:

1	auto
2	s300bps
3	s1200bps
4	s2400bps
5	s4800bps
6	s9600bps
7	s19200bps
8	s38400bps
9	s57600bps
10	s115200bps

.1.3.6.1.4.1.164.3.3.3.2.2.1.24

prtT1E1LineMode

Interface type of the port.
For T1 - csu, dsu are the valid values
For E1 - dsu, ltu are the valid values

Enumerationr/w

Enumerated Values:

1	dataBits7
2	dataBits8

.1.3.6.1.4.1.164.3.3.3.2.2.1.25

prtT1E1TS0SaBits

This object is applicable only for E1 ports. For T1, string size will be 0.
For E1, it enables user to select the use of TS0 Sa Bits 4..8, by 3 octets:
The order (in hexa display):
free Sa-Bit-4 Sa-Bit-5 Sa-Bit-6 …

OctetStringr/w

Enumerated Values:

1	none
2	odd
3	even

.1.3.6.1.4.1.164.3.3.3.2.2.1.26

prtT1E1ConnectedTS

This parameter indicates if there is any connected TS for this interface.

Enumeration

Enumerated Values:

1	notApplicable
2	none
3	all
4	major

.1.3.6.1.4.1.164.3.3.3.2.2.1.27

prtT1E1Ts0SaBit

This parameter indicates whether to send TS 0, or not.
noMng= TS 0 is looped, therefore not sent.
mng= TS 0 isn't looped, therefore it is sent.

Enumerationr/w

Enumerated Values:

1	dce
2	dte

.1.3.6.1.4.1.164.3.3.3.2.2.1.28

prtT1E1SameFeCnfg

This parameter indicates whether the same E1 configuration
parameters and TS assignment are set both to the local
and remote device.
Read-Write access is applicable only in G732N framed mode.
For G732S and UNFRAMED thi…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	on
3	rts

.1.3.6.1.4.1.164.3.3.3.2.2.1.29

prtT1E1RemCrc4

This object indicates whether the E1 of the Remote device
connected to this E1 port, will have CRC-4 or not.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	d0
3	d10
4	d50
5	d100
6	d200
7	d300

.1.3.6.1.4.1.164.3.3.3.2.2.1.30

prtT1E1MaxTSs

This object is applicable only for DXC D4T1, D4E1, D8T1, D8E1
external ports and D8GSL internal E1 ports.
It is relevant only when sysCIntTsAllocMode=static(2).
255=not applicable
If prtT1E1LineType=unframed(8), th…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	on
3	dtr

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.2.2.1.31

prtT1E1EocTsConfig

This object indicates whether the use of EOC for TS Configuration
is enabled or not.

Enumerationr/w

Constraints:
range: 0-8

.1.3.6.1.4.1.164.3.3.3.2.2.1.32

prtT1E1Role

This object indicates whether this port behaves as SUB or Main link.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	t30sec
3	t45sec
4	t60sec

.1.3.6.1.4.1.164.3.3.3.2.2.1.33

prtT1E1PppEchoFailDetection

Enumerationr/w

Enumerated Values:

1	notApplicable
2	tone
3	pulse

.1.3.6.1.4.1.164.3.3.3.2.2.1.34

prtT1E1FdlMsgTable

table

.1.3.6.1.4.1.164.3.3.3.2.3 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtT1E1FdlMsgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtT1E1FdlMsgTable'

This table is applicable for a T1 interface with 'esf'
LineType or E1 interface, when CRC is enabled (LineType).

prtT1E1FdlMsgEntry row .1.3.6.1.4.1.164.3.3.3.2.3.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtT1E1FdlMsgPrtIdx

SNMPv2-SMIInteger32

Constraints:
range: 0-20

.1.3.6.1.4.1.164.3.3.3.2.3.1.1

prtT1E1FdlMsgFdlType

The Fdl type reference of the Fdl message.

Enumeration

Enumerated Values:

1	notApplicable
2	none
3	proprietary
4	rip2

.1.3.6.1.4.1.164.3.3.3.2.3.1.2

prtT1E1FdlMsgSlt

This attribute indicates a unique number to identify the slot where
the card is inserted in.
When the unit is stand-alone, this object is not applicable
and 255 will be used.

Enumeration

Constraints:
range: 20-20

.1.3.6.1.4.1.164.3.3.3.2.3.1.3

prtT1E1FdlMsg

FDL message.

OctetString

Enumerated Values:

1	notApplicable
2	always
3	linkFail

.1.3.6.1.4.1.164.3.3.3.2.3.1.4

prtHSParamTable

table

.1.3.6.1.4.1.164.3.3.3.3.1 · 1 row entry · 16 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtHSParamTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtHSParamTable'

A table.

prtHSParamEntry row .1.3.6.1.4.1.164.3.3.3.3.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtHSCnfgIdx

This attribute indicates the Idx of the Config being accessed.
Idx of 255 relates to the Temporary (Scratch) Config.

Integer32

.1.3.6.1.4.1.164.3.3.3.3.1.1.1

prtHSPrtIdx

This attribute indicates a unique number to identify a port.
The valid port number depends on the IO slot no., the
installed card type and the port type: outside, inside,
SP.
* The inside ports will be the HS cards …

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.3.1.1.2

prtHSSlt

This attribute indicates a unique number to identify the slot where
the card is inserted in.
When the unit is stand-alone, this object is not applicable
and 255 will be used.

Enumeration

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.3.3.3.1.1.3

prtHSRate

This object indicates the port rate (speed).
auto - rate is selected automatically by system.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.3.1.1.4

prtHSFifoSize

This object selects the size of the user data channel buffer
FIFO used in the DTE2 mode. In the other modes, buffer
size is automatically set by the DACS agent.
Buffer FIFO size in bits, corresponds to FIFO lengths of…

Enumerationr/w

Enumerated Values:

2	regularTx
3	broadcast

.1.3.6.1.4.1.164.3.3.3.3.1.1.5

prtHSClkMode

Clock Mode of the user data channel.
dce - DACS operates as a DCE and provides transmit
and receive clocks to the synchronous user DTE.
dte1- DACS supplies the receive clock to the user
equipment and acce…

Enumerationr/w

Enumerated Values:

2	normalClk
3	inverted

.1.3.6.1.4.1.164.3.3.3.3.1.1.6

prtHSCTS

Selection of CTS line state in the user data channel.
on - CTS continuously ON.
rts - CTS line follows the RTS line.

Enumerationr/w

Enumerated Values:

2	extDce
3	dce
4	smooth
5	extSmooth

.1.3.6.1.4.1.164.3.3.3.3.1.1.7

prtHSRtsState

RTS state of the port.

Enumeration

Enumerated Values:

2	t16msec
3	t64msec

.1.3.6.1.4.1.164.3.3.3.3.1.1.8

prtHSInbandLoopback

This object indicates if Inband Loopback from the Network
should be enabled or disabled.

Enumerationr/w

Enumerated Values:

2	disabled
3	ts1
4	dedicatedFr

.1.3.6.1.4.1.164.3.3.3.3.1.1.9

prtHSInbandLoopPatternCfg

This object indicates if Inband Loop polynomial pattern
will be according to RDL Loop (the standard) or User Configurated
according to prtHSActivatePolyPattern and prtHSDeactivatePolyPattern.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	none
3	proprietary

.1.3.6.1.4.1.164.3.3.3.3.1.1.10

prtHSInbandLoopActPattern

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.3.3.3.1.1.11

prtHSInbandLoopDeactPattern

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.3.3.3.1.1.12

prtHSDCD

Selection of DCD line state in the user data channel.
linkOK - DCD line is ON only when active link is OK.
on - DCD continuously ON.

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.3.3.3.1.1.13

prtHSClkPolarity

This object indicates the clock polarity.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.3.1.1.14

prtHSInterfaceType

This object indicates the selected electrical interface type.

Enumerationr/w

Constraints:
range: 1-8

.1.3.6.1.4.1.164.3.3.3.3.1.1.15

prtHSUnframed

Unframed line for HS ports.
yes - means that all TSs must be transferred, including TS0.
In this case, prtHSRate must be r31x56eq1736Kbps OR
r31x64eq1984Kbps.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.3.1.1.16

prtHSBertTable

table

.1.3.6.1.4.1.164.3.3.3.3.2 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtHSBertTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtHSBertTable'

A table.

prtHSBertEntry row .1.3.6.1.4.1.164.3.3.3.3.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtHSBertPrtIdx

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.3.2.1.1

prtHSBertSlt

This attribute indicates a unique number to identify the slot where
the card is inserted in.
When the unit is stand-alone, this object is not applicable
and 255 will be used.

Enumeration

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.3.3.3.2.1.2

prtHSBertCountClr

Setting this object (to on) initiate bert counter clear
operation.
Valid only when bert test is active on the specific port.
(Every time a new bert test starts, the counter is
automatically cleared; this command enabl…

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.3.2.1.3

prtHSBertTestResult

This object indicates the number of Bit Error Rate indicated
during the BERT test.
Active only when bert test is running on the selected port.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	nc
3	r2bit
4	r4bit
5	r8bit

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.3.2.1.4

prtSpCnfgTable

table

.1.3.6.1.4.1.164.3.3.3.4.1 · 1 row entry · 22 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtSpCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtSpCnfgTable'

A table.

prtSpCnfgEntry row .1.3.6.1.4.1.164.3.3.3.4.1.1

All the entries at this table are identical(have the same value)
at all the configurations(1..255) except at the TmpCnfg.
- For products supporting more than one configuration, the write operation
into the Table Obje…

Indexes

No indexes recorded

Column Syntax OID

prtSpCnfgIdx

This attribute indicates the Idx of the Cnfg(1..255) being
accessed.
Idx of 255 relates to the TmpCnfg.

Integer32

.1.3.6.1.4.1.164.3.3.3.4.1.1.1

prtSpPrtIdx

This attribute indicates a unique port number of the SPor DP port.
For DXC, it is the port in the active DCL card:
- SP = 1
- NP ; DP = 2

For Kilomux, the port index is calculated as follows:
1…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.4.1.1.2

prtSpUsage

This attribute indicates what is the usage of the port.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	central
3	remote

.1.3.6.1.4.1.164.3.3.3.4.1.1.3

prtSpRate

This attribute indicates the operation rate (speed) of the port.
auto - automatic rate selection, by the agent.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	none
3	hrpt

.1.3.6.1.4.1.164.3.3.3.4.1.1.4

prtSpDataBits

This attribute indicates the number of data bits in async
frame

Enumerationr/w

Enumerated Values:

1	notApplicable
2	r192
3	r256
4	r320
5	r384
6	r448
7	r512
8	r576
9	r640
10	r768
11	r896
12	r1024
13	r1152
14	r1280
15	r1536
16	r1920
17	r2048

.1.3.6.1.4.1.164.3.3.3.4.1.1.5

prtSpParity

This attribute indicates the parity mode in async frame

Enumerationr/w

Enumerated Values:

1	notApplicable
2	msdsl2w
3	hdsl2w
4	hdsl4w
5	gDsl

.1.3.6.1.4.1.164.3.3.3.4.1.1.6

prtSpCallOutMode

This attribute indicates the call-out mode.
For DXC - this object is applicable only for the DP port (2).

Enumerationr/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.3.3.4.1.1.7

prtSpInterface

This attribute indicates the supervisory port interface.
dce - the DACS appears as a DCE for the port.
dte - the DACS operates as a DTE, for connection via modem,
for the port.

Enumerationr/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.3.3.4.1.1.8

prtSpCTS

CTS line state. This object is applicable only for
port (1) = SP

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.4.1.1.9

prtSpDcdDelay

DCD delay in msec.
d10 = delay of 10msec.
This object is applicable only for port (1) = SP

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.4.1.1.10

prtSpDsr

DSR line state. This object is applicable only for
port (1) = SP

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.3.3.4.1.1.11

prtSpNoOfRetries

For DXC - this object is applicable only for port (2) = DP.
The number of dialing retries requested.
Default = 0

Integer32r/w

.1.3.6.1.4.1.164.3.3.3.4.1.1.12

prtSpWaitForConnect

For DXC - this object is applicable only for port (2) = DP.
Waiting time for connect, in seconds.
Default = 30 sec.

Enumerationr/w

Enumerated Values:

3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
17	io13
18	io14
19	io15
255	standAlone

.1.3.6.1.4.1.164.3.3.3.4.1.1.13

prtSpDialMode

For DXC - this object is applicable only for port (2) = DP.
Dialing mode.
Default=tone

Enumerationr/w

Enumerated Values:

1	notApplicable
2	len0p450ft
3	len451p900ft

.1.3.6.1.4.1.164.3.3.3.4.1.1.14

prtSpAltNumMode

For DXC - this object is applicable only for port (2) = DP.
It determines wether to use the alternate number or not.
Default = no.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	off
3	cBit
4	cBitTxRxMng
5	cBitTx
6	cBitTxMng
7	m13
8	cdpv
9	nationalBit

.1.3.6.1.4.1.164.3.3.3.4.1.1.15

prtSpPrimaryNum

For DXC - this object is applicable only for port (2) = DP.
It is the Primary dialing number.

OctetStringr/w

Enumerated Values:

1	notApplicable
2	unframed
3	framed

.1.3.6.1.4.1.164.3.3.3.4.1.1.16

prtSpAltNum

For DXC - this object is applicable only for port (2) = DP.
It is the Alternate dialing number. This number
is applicable only if prtSpAltNumMode is 'yes'.

OctetStringr/w

Enumerated Values:

1	external
2	internal
255	notApplicable

.1.3.6.1.4.1.164.3.3.3.4.1.1.17

prtSpRoutProtocol

This attribute indicates the routing protocol of the port.
notApplicable - for DP.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	none
3	proprietary
4	rip2

.1.3.6.1.4.1.164.3.3.3.4.1.1.18

prtSpCmd

SP Command.
For LRS this parameter will be used for a Modem Command.
Upon NMS's Get operation for devices that this parameter
is notApplicable, agent will send NULL string.

OctetStringr/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.3.3.4.1.1.19

prtSpActCallOut

This object indicates when to Activate Call-Out.
It is used by FCD-T1/E1.
always - to activate call-out always.
linkFail - to activate call-out only when Link of Inband Management fails.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.4.1.1.20

prtSpAlrRelayMode

This attribute indicates the Alarm Relay Mode.
notApplicable - for DP.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.4.1.1.21

prtSpStopBits

This attribute indicates number of stop bits in an async frame.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.4.1.1.22

prtDimCnfgTable

table

.1.3.6.1.4.1.164.3.3.3.5.1 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtDimCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtDimCnfgTable'

A table.

prtDimCnfgEntry row .1.3.6.1.4.1.164.3.3.3.5.1.1

The write operation into the Table Objects is valid only
for the TmpCnfg entry (prtDimCnfgIdx=255).

Indexes

No indexes recorded

Column Syntax OID

prtDimCnfgIdx

This attribute indicates the Idx of the Cnfg(1..255) being
accessed.
Idx of 255 relates to the TmpCnfg.

Integer32

Enumerated Values:

1	psA
2	psB
3	clA
4	clB
5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
17	io13
18	io14
19	io15
255	notApplicable

.1.3.6.1.4.1.164.3.3.3.5.1.1.1

prtDimIdx

This attribute indicates a unique port number of the
DIM card.
The convention used for DXC:
(IO slot number+10)*10 + 1
Example: port1 of IO slot 11 will be: 211 .

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.5.1.1.2

prtDimTxMode

Tx mode.
regularTx - the links are connected to a similar outfit on
the other side. In this mode, if a link fails,
the transmitted bandwidth is decreased
accordingly.
broadcast - t…

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.5.1.1.3

prtDimPolarity

Polarity.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.5.1.1.4

prtDimClkMode

Clock Mode.
smooth - a clock that is not 'pulsed'(has no 'gaps'). In this mode
the DXC does NOT receive back the clock signal.
extSmooth - same as 'smooth' but in this mode, the DXC receives back
t…

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.5.1.1.5

prtDimMaxDelay

Max Delay permitted between the links, in msec.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.5.1.1.6

prtDimMng

Use of DIM port for management.
disabled - no management on DIM
ts1 - 1 bit of TS1 is used for management.

Enumerationr/w

Enumerated Values:

5	io1
6	io2
7	io3
8	io4
9	io5
10	io6
11	io7
12	io8
13	io9
14	io10
15	io11
16	io12
17	io13
18	io14
19	io15
255	standAlone

.1.3.6.1.4.1.164.3.3.3.5.1.1.7

prtDimMngRoutProt

Mng Routing Protocol of the port.
none - when prtDimMng is 'disabled'.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.5.1.1.8

prtDimDestTable

table

.1.3.6.1.4.1.164.3.3.3.5.2 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtDimDestTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtDimDestTable'

A table.

prtDimDestEntry row .1.3.6.1.4.1.164.3.3.3.5.2.1

The write operation is valid only for the TmpCnfg entry
(prtDimDestCnfgIdx=255).

Indexes

No indexes recorded

Column Syntax OID

prtDestCnfgIdx

This attribute indicates the Idx of the Cnfg(1..255) being
accessed.
Idx of 255 relates to the TmpCnfg.

Integer32

.1.3.6.1.4.1.164.3.3.3.5.2.1.1

prtDestDimIdx

This attribute indicates a unique port number of the
DIM card.
The convention used for DXC:
(IO slot number+10) & 1
Example: port1 of IO slot 11 will be: 211 .

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.5.2.1.2

prtDestIdx

This attribute indicates a destination number of the
DIM card.

Integer32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.3.3.5.2.1.3

prtDest

Destination port,(of a T1/E1 port), that is connected to the
DIM card, for the specified Destination number.
0 = No destination port.
Else:
For external ports:
(IO Slot+10) & 1 for port 1
(IO Slot+10) & 3 for p…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	system
3	card
4	port

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.5.2.1.4

prtDestConnect

Connection Status of the specified destination number.
For a specified destination port, it depends both on the
status of the port and on the status of the far-end port.
Since this is a RO object, same value will be re…

Enumeration

Enumerated Values:

1	notApplicable
2	ps
3	cl
4	io
5	clAndIo

.1.3.6.1.4.1.164.3.3.3.5.2.1.5

prtICnfgTable

table

.1.3.6.1.4.1.164.3.3.3.6.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtICnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtICnfgTable'

A table.

prtICnfgEntry row .1.3.6.1.4.1.164.3.3.3.6.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtICnfgIdx

This attribute indicates the Idx of the Config being accessed.
Idx of 255 relates to the Temporary (Scratch) Config.

Integer32

Enumerated Values:

1	notApplicable
3	event
4	minor
5	major
6	warning
7	critical

.1.3.6.1.4.1.164.3.3.3.6.1.1.1

prtIIdx

This attribute indicates a unique number to identify a port.
The valid port number depends on the IO slot no., the
installed card type and the port type: outside, inside,
SP.
* The ISDN B1, B2, D channels will be in…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.6.1.1.2

prtIRate

This object indicates the port rate in bits.
Each TS contains 8 bits. Thus, 1 bit is equivalent to 8Kbps
rate.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.6.1.1.3

prtIConnect

D channel connection.
no - disconnected
yes - connected.

Enumerationr/w

Enumerated Values:

1	central
2	remote
3	remote2
4	remote3
5	remote4
6	remote5
7	remote6
8	remote7
9	remote8
10	remote9
11	remote10

.1.3.6.1.4.1.164.3.3.3.6.1.1.4

prtHdslTable

table

.1.3.6.1.4.1.164.3.3.3.7.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtHdslTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtHdslTable'

HDSL port table.

prtHdslEntry row .1.3.6.1.4.1.164.3.3.3.7.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtHdslIdx

This attribute indicates a unique number to identify a port.
The valid port number depends on the IO slot no., the
installed card type and the port type: outside, inside.
* The HDSL ports will be external.
For port …

SNMPv2-SMIInteger32

Enumerated Values:

2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.7.1.1.1

prtHdslMode

This object indicates the HDSL mode.

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.3.3.7.1.1.2

prtHdslRptrType

The Repeater between Near and Far modem.
none - no repeater exists between the modems
hrpt - HRPT repeater exists between the modems.

Enumeration

Enumerated Values:

2	external
3	internal
4	station

.1.3.6.1.4.1.164.3.3.3.7.1.1.3

prtHdslMaxRate

Maximum Rate of the xDSL Line, in Kbps units.
This object can be Set only for a Central unit.

Enumerationr/w

Enumerated Values:

2	off
3	on
255	notApplicable

.1.3.6.1.4.1.164.3.3.3.7.1.1.4

prtHdslLinkType

The Link Type.
msdsl2w - MSDSL 2 Wire
hdsl2w - HDSL 2 Wire
hdsl4w - HDSL 4 Wire
gDsl - G.DSL

Enumeration

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.3.3.7.1.1.5

prtHdslCompSwVer

This object indicates the Software Version of the
component (Piggyback card) supporting this interface.

OctetString

Enumerated Values:

2	off
3	hw
4	hwAndConfig
255	notApplicable

.1.3.6.1.4.1.164.3.3.3.7.1.1.6

prtHdslCompHwVer

This object indicates the Hardware Version of the
component (Piggyback card) supporting this interface.

OctetString

Enumerated Values:

1	notApplicable
2	off
3	on

.1.3.6.1.4.1.164.3.3.3.7.1.1.7

prtT3E3CnfgTable

table

.1.3.6.1.4.1.164.3.3.3.8.1 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtT3E3CnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtT3E3CnfgTable'

T3/E3 port configuration table.

prtT3E3CnfgEntry row .1.3.6.1.4.1.164.3.3.3.8.1.1

An entry in the T3/E3 port configuration table.

Indexes

No indexes recorded

Column Syntax OID

prtT3E3CnfgIdx

This attribute indicates the Idx of the Config being accessed.
Idx of 255 relates to the Temporary (Scratch) Config.
For DXC, write operations can be performed only on the Temp Config.
For products that do not support c…

Integer32

.1.3.6.1.4.1.164.3.3.3.8.1.1.1

prtT3E3PrtIdx

This attribute indicates a unique port number.
For DXC:
The same numbering as for prtGenPrtIdx.
The valid port number depends on the IO slot no., the
installed card type and the port type: outside, inside.
* The ext…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.3.8.1.1.2

prtT3E3Slt

This attribute indicates a unique number to identify the slot where
the card is inserted in.
When the unit is stand-alone, this object is not applicable
and 255 will be used.

Enumeration

.1.3.6.1.4.1.164.3.3.3.8.1.1.3

prtT3E3LineLength

This object is the length of the ds3 line in feet.
It provides information for line build out circuitry if it exists
and can use this object to adjust the line build out.
len0p450ft = 0 - 450 feet
len451p900ft =…

Enumerationr/w

Constraints:
range: 10-10

.1.3.6.1.4.1.164.3.3.3.8.1.1.4

prtT3E3InbandMng

A unique number to identify the Frame Type over the link.
For Optimux-T3: only values (4), (7) are supported.

Enumerationr/w

Enumerated Values:

1	master
2	fallback

.1.3.6.1.4.1.164.3.3.3.8.1.1.5

prtT3E3AisFrame

This object is applicable only for Optimux-T3.
It allows user to select whether the AIS sent will be framed or unframed.

Enumerationr/w

Constraints:
range: 10-10

.1.3.6.1.4.1.164.3.3.3.8.1.1.6

prtT3E3TxClockSource

Tx Clock Source.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	amc102SA
3	amc102Card

.1.3.6.1.4.1.164.3.3.3.8.1.1.7

prtT3E3RoutProt

Routing Protocol of the port.
This object is applicable only for T3 ports.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.8.1.1.8

prtT3E3AisTransmit

Indicates if AIS signal will be transmitted over the tributary E3/DS3
upon failure.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.3.8.1.1.9

cmprTable

table

.1.3.6.1.4.1.164.3.3.4.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk cmprTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::cmprTable'

A table.

cmprEntry row .1.3.6.1.4.1.164.3.3.4.1.1

An entry in table.

Indexes

modmSaConfigMode modmSaAlarmBuffIndex

Column Syntax OID

cmprTypeIdx

This object indicates the Type of the Compressed
data referred (which table, which level, etc).
The type is a code according to a convention between
agent and NMS.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.4.1.1.1

cmprCnfgIdx

This object indicates the configuration number the
Compressed information relates to.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.4.1.1.2

cmprVersion

This object indicates the version of the internal format of
the Compressed data (the version of the convention used).

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.4.1.1.3

cmprSltIdx

This attribute indicates a unique number of the slot
position where the card is inserted.
When the unit is stand-alone or this object is not applicable,
255 will be used.

Enumeration

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.3.4.1.1.4

cmprPrtIdx

This object indicates a unique identifier of the port,
the compressed information relates to.
For DXC - according to the order in the card of cmprSltIdx:
- first two digits will be: (IO slot number+10)
- last one/two di…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.4.1.1.5

cmprObj

This object is the compressed information itself,
according to a predefined format, both agent and NMS agreed
about.

OctetStringr/w

.1.3.6.1.4.1.164.3.3.4.1.1.6

mapLinkTable

table

.1.3.6.1.4.1.164.3.3.4.2 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mapLinkTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mapLinkTable'

A table.

mapLinkEntry row .1.3.6.1.4.1.164.3.3.4.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

mapLinkIdx

A unique identifier of the link

SNMPv2-SMIInteger32

Enumerated Values:

1	none
2	loopLHrpt

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.4.2.1.1

mapLinkSlotIdx

This attribute indicates a unique slot position where
the module is inserted.

Enumerationr/w

.1.3.6.1.4.1.164.3.3.4.2.1.2

mapLinkPortIdx

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	off
2	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.4.2.1.3

mapLinkState

This attribute indicates the status of the link between
the two muxes

Enumeration

.1.3.6.1.4.1.164.3.3.4.2.1.4

alrGenTable

table

.1.3.6.1.4.1.164.3.3.4.3 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk alrGenTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::alrGenTable'

A table.

alrGenEntry row .1.3.6.1.4.1.164.3.3.4.3.1

An entry in table.

Indexes

mdlSIdx

Column Syntax OID

alrGenCode

This object is a unique code number, identifying
a certain alarm.

SNMPv2-SMIInteger32

Enumerated Values:

1	psA
2	psB
3	cl
4	io1
5	io2
6	io3
7	io4
8	io5
9	io6
10	io7
11	io8
12	io9
13	io10
14	io11
15	io12

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.3.4.3.1.1

alrGenDescription

This entry is a unique text description, of the alarm
corresponding to the specified code.

OctetString

.1.3.6.1.4.1.164.3.3.4.3.1.2

alrGenLevel

Alarm level.

Enumeration

Enumerated Values:

1	unknown
2	empty
3	ps48V
4	ps110V
5	ps230V
6	cm2
7	smod
8	asmi24
9	asmi31
10	asmi32
11	asmi50
12	mtmi20
13	fomi40
14	fomiE1T1
15	asm40cd
16	asmi50cd
17	fomi40cd
18	fomiE1T1cd
19	ps110V-24
20	ps230V-24
21	ps48V-24
22	asmi31cq
23	asmi51cq
24	asmi51cd
25	asmi52cd
26	asmi52cq
27	asmi52cd4W
28	asmi52cqEth
29	asmi52cd4wNew
30	asmi52cd4wNewEth
51	fomiE3
52	fomiT3
53	optimux4E1
54	optimux4T1
55	amc102
255	notApplicable

.1.3.6.1.4.1.164.3.3.4.3.1.3

alrGenSlotType

Slot type that the alarm is relevant to.
clAndIo - an alarm that is relevant for both CL and IO slots.

Enumeration

Enumerated Values:

1	empty
2	f2
3	f3
5	f5
6	f6
7	f7
9	f9
10	f10
11	f11
12	f12
13	f13
14	f14
15	f18
16	f19
17	f22
18	f20
19	f21
20	f23
21	fO1
22	fO2
23	fO3
24	fO4
25	fO5
26	fO6
27	fO7
28	fO8
29	fO9
30	fO10
31	fO11
32	fO12
33	fO13
34	fO14
35	fO15
36	fO16
37	fO17
38	fO18
39	fO19
40	fO20
41	fO21
42	fO22
81	ps230And115
82	psp230And115
83	ps48
84	psp48
91	f1Cm2
92	f2Cm2
93	f3Cm2
94	f4Cm2
95	f5Cm2
96	f1Cm2New
121	f24
122	f25
123	f27
124	f28
125	f29
126	f30
127	f31
128	f32
255	notApplicable

.1.3.6.1.4.1.164.3.3.4.3.1.4

alrGenSeverity

This object enables the user to select a severity for each alarm.
The severity is set per alarm code (same for all slots/ports
using this code).

Enumerationr/w

.1.3.6.1.4.1.164.3.3.4.3.1.5

alrGenDebounce

Debounce time for each alarm code, in seconds.
The meaning is, that an alarm will be 'declared' as ON (or OFF), only
after it was actually ON/OFF the Debouncing time selected by user.
0 = default debounce selection (ea…

Integer32r/w

.1.3.6.1.4.1.164.3.3.4.3.1.6

alrGenDefSeverity

This object reports the default severity of each alarm.
User can change the severity of the alarms defined by
this default via the alrGenSeverity object.

Enumeration

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.3.4.3.1.7

modmSaConfigTable

table

.1.3.6.1.4.1.164.3.4.1.1.1 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk modmSaConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::modmSaConfigTable'

Configuration parameters of the Central and Remote Modems.
The table will be RW for a Central agent and RO for a 
Remote agent.

modmSaConfigEntry row .1.3.6.1.4.1.164.3.4.1.1.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

modmSaConfigMode

The mode indicates if the configuration parameters refer
the Central or the Remote Modem.
For AMC 102 the remote means regenerator.
There can be some regenerators connecting one by the other.

Enumeration

Enumerated Values:

1	notApplicable
2	disconnect
3	connect

.1.3.6.1.4.1.164.3.4.1.1.1.1.1

modmSaConfigLoopback

The possible loopbacks. It is not possible to have a
remPortLoop(4) in both, Central and Remote units
simultaneously.

Enumerationr/w

.1.3.6.1.4.1.164.3.4.1.1.1.1.2

modmSaConfigAlrClearOnCmd

Setting this attribute to on, clears all the events,
both from the active alarms list and from the alarms buffer.
Upon completion, the value will automatically change to
off(2).

Enumerationr/w

Enumerated Values:

9	internal
10	external
11	system
12	receive
255	notApplicable

.1.3.6.1.4.1.164.3.4.1.1.1.1.3

modmSaConfigAlrClearAllCmd

Setting this attribute to on, clears all the alarms of the
alarm buffer and active alarms list. Upon completion, the
value will automatically change to off(2).

Enumerationr/w

.1.3.6.1.4.1.164.3.4.1.1.1.1.4

modmSaConfigTestClearCmd

Setting this attribute to on, clears all the user-initiated
tests and loopbacks. The variable modmSaConfigLoopback should
automatically change to noLoopback. Upon completion, the
value will automatically change to off(…

Enumerationr/w

.1.3.6.1.4.1.164.3.4.1.1.1.1.5

modmSaConfigClkMaster

Modem configured as Central:
External - Locked to the clock signal provided by the user's
equipment by user's port.
Internal - Internal oscillator.
Station - Station clock (is relevant only for c…

Enumerationr/w

.1.3.6.1.4.1.164.3.4.1.1.1.1.6

modmSaConfigResetStatistics

In the on state all statistics counters (including E1
counters) are zeroed. Upon completion, the value will
automatically change to off(2).
Modems that do not support statistics - the value will
always be off (this …

Enumerationr/w

Enumerated Values:

1	unknown
2	asmi24c
3	asmi31c
4	asmi32c
5	asmi50c
6	mtmi20c
7	fomi40c
8	fomiE1T1c
9	asm40cd
10	asmi31cq
11	asmi51cq
12	asmi51cd
13	asmi52cq
14	asmi52cd
15	asmi52cd4W
16	asmi52cqEth
17	asmi52cd4wNew
18	asmi52cd4wNewEth
22	asmi24r
23	asmi31r
24	asmi32r
25	asmi50r
26	mtmi20r
42	asmi24
43	asmi31
44	asmi32
45	asmi50
46	mtmi20
47	fomi40
48	fomiE1T1
49	asmi51
50	asmi52S
51	asmi52M
52	asmi52L
53	asmi54
71	lrs52

.1.3.6.1.4.1.164.3.4.1.1.1.1.7

modmSaConfigActiveTs

This object will be RO for the Remote modem.
This is the number of active HDSL Time Slots, that
determines user's data rate.
Valid values: 1..maximum supported by the specific modem.
255 = notApplicable.

Integer32r/w

Enumerated Values:

1	master
2	slave

.1.3.6.1.4.1.164.3.4.1.1.1.1.8

modmSaConfigReset

Reset of modem.
hw - HW Reset. The configured values will not change.
hwAndConfig - HW Reset and initializing the default values.
notApplicable - for modems with no Reset support.
After 'hw' or 'hwAndConfig' is Set, age…

Enumerationr/w

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.4.1.1.1.1.9

modmSaConfigRemote

This parameter enables or disables automatic configuration
of the remote moden in Proxy mode.

Enumerationr/w

.1.3.6.1.4.1.164.3.4.1.1.1.1.10

modmSaConfigPsType

The type of PS.

Enumeration

Enumerated Values:

1	w2wire
2	w4wire
255	notApplicable

.1.3.6.1.4.1.164.3.4.1.1.1.1.11

modmSaConfigWorkMode

The work mode indicates if devices work in transparent mode or termination mode.

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.4.1.1.1.1.12

modmSaStatTable

table

.1.3.6.1.4.1.164.3.4.1.1.2 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk modmSaStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::modmSaStatTable'

Status of the Central and Remote Modems.

modmSaStatEntry row .1.3.6.1.4.1.164.3.4.1.1.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

modmSaStatHwTest

The variable contains the results of the last hardware test.
It is a sum of 2**n where n is as follows:
0 - EPROM Failure (or Database chksum error)
1 - I/O Expander Error
2 - Counter Error
3 - HDSL Framer Failure
4 - …

SNMPv2-SMIInteger32

Constraints:
range: 2-2

.1.3.6.1.4.1.164.3.4.1.1.2.1.1

modmSaStatAlarms

The variable contains the status of the Alarms in the alarm
buffer.
For bit location of each Alarm in the OctetString see Modem's
specification.
If the value is 0 then there are No 'On' Alarms in the alarm
buffer.

OctetString

.1.3.6.1.4.1.164.3.4.1.1.2.1.2

modmSaStatClkSrc

This entry indicates the source of the modem clock.

Enumeration

Enumerated Values:

1	ac
2	dc
255	notApplicable

.1.3.6.1.4.1.164.3.4.1.1.2.1.3

modmSaStatAlarmsMask

This variable uses to mask alarms.
Location of each Alarm Mask in the OctetString,
is identical to the Alarm OctetString.
If the value is 0 then none of the alarms is masked.

OctetStringr/w

.1.3.6.1.4.1.164.3.4.1.1.2.1.4

modmSaStatDeviceType

This entry indicates the device type (or utility).

Enumeration

.1.3.6.1.4.1.164.3.4.1.1.2.1.5

modmSaStatSwVersion

Display String of the modem SW version.
Format: W. X Y Z
0..9 0..99 A,B,E 0..99
(Z+P are optional.)
A=alpha, B=beta, E=end of development.
Examples: 2.23A8
3.4

SNMPv2-TCDisplayString

Enumerated Values:

2	off
3	on

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.4.1.1.2.1.6

modmSaStatHwVersion

Display String of the modem HW version.

SNMPv2-TCDisplayString

Enumerated Values:

2	off
3	on

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.4.1.1.2.1.7

modmSaAlarmBuffTable

table

.1.3.6.1.4.1.164.3.4.1.1.3 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk modmSaAlarmBuffTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::modmSaAlarmBuffTable'

The alarm buffer of the Central and Remote Modems.

modmSaAlarmBuffEntry row .1.3.6.1.4.1.164.3.4.1.1.3.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

modmSaAlarmBuffIndex

The index of the alarm buffer Table.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.4.1.1.3.1.1

modmSaAlarmBuffCode

The code of the alarm. For text description of each Alarm
code see Modem's specification.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.4.1.1.3.1.2

modmSaAlarmBuffTime

The time stamp at which the alarm has occurred. The format
is hh:mm:ss

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.4.1.1.3.1.3

modmSaAlarmBuffState

The new status of the alarm.

Enumeration

.1.3.6.1.4.1.164.3.4.1.1.3.1.4

modmSaRptrTable

table

.1.3.6.1.4.1.164.3.4.1.1.5 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk modmSaRptrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::modmSaRptrTable'

The Repeaters parameters known to the central modem.

modmSaRptrEntry row .1.3.6.1.4.1.164.3.4.1.1.5.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

modmSaIndex

A unique number to identify the modem that reports about the repeater.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.4.1.1.5.1.1

modmSaRptrIndex

The index of the Repeater.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.4.1.1.5.1.2

modmSaRptrTest

The possible loopbacks.

Enumerationr/w

.1.3.6.1.4.1.164.3.4.1.1.5.1.3

modmSaRptrActiveAlarms

Status of the Alarms. Each bit represents a specific
alarm .
For bit location of each alarm in the
Octet String see modem's specification.
If the value is 0 then there are No Alarms.

OctetString

.1.3.6.1.4.1.164.3.4.1.1.5.1.4

modmSaRptrAlrClear

Setting this attribute to on, clears all the active (On)
alarms of the repeater. Upon completion, the value will
automatically change to off(2)..

Enumerationr/w

Enumerated Values:

1	notApplicable
2	off
3	on

.1.3.6.1.4.1.164.3.4.1.1.5.1.5

modmSaRptrVersion

SW/HW version of the repeater

SNMPv2-TCDisplayString

Enumerated Values:

1	notApplicable
2	r2Mbps
3	r4Mbps

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.4.1.1.5.1.6

mdlParamTable

table

.1.3.6.1.4.1.164.3.4.2.1.1 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlParamTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlParamTable'

Parameters table of cards in the Hub.

mdlParamEntry row .1.3.6.1.4.1.164.3.4.2.1.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

mdlSIdx

A unique number to identify a slot position in the modems
Hub.

Enumeration

.1.3.6.1.4.1.164.3.4.2.1.1.1.1

mdlSNoOfModems

Number of modems on this card.
255 = notApplicable.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.4.2.1.1.1.2

mdlCardType

Card's type.

Enumeration

Enumerated Values:

1	invalid
2	valid

.1.3.6.1.4.1.164.3.4.2.1.1.1.3

mdlSPanelType

LRS-12 Card connectors' panel type.
fx - IMOD panels
psxxx - PS panels
fxCm2 - CM-2 panels.

Enumeration

Enumerated Values:

1	noOp
2	swdl

.1.3.6.1.4.1.164.3.4.2.1.1.1.4

mdlSLed

LEDs status on the card . Each led will be represented by 4
bits where the first 2 bits (left) will specify the Status :
(00=NA, 01=OFF, 10=ON, 11=BLINK),
and the next two bits (right) will specify the Color :
(00=GRE…

OctetString

.1.3.6.1.4.1.164.3.4.2.1.1.1.5

mdlSActiveAlarms

This object is applicable only for PS and CL cards.
It gives the status of the Alarms for each Slot. Each bit
represents an alarm in the slot. For bit location of each
Alarm in the Octet String see Hub's specification…

OctetString

.1.3.6.1.4.1.164.3.4.2.1.1.1.6

mdlAlrClear

Setting this attribute to on, clears all the active (On)
alarms of the Slot. Upon completion, the value will
automatically change to off(2).

Enumerationr/w

.1.3.6.1.4.1.164.3.4.2.1.1.1.7

mdlSConfigMismatch

This object is applicable only for slots containing
IMOD cards.
ON - when CM-2 realizes that the configuration of the
Near-End modem1 is different from that of its Far-End
modem.
In this case it expec…

Enumeration

.1.3.6.1.4.1.164.3.4.2.1.1.1.8

mdlConfigSource

This object is applicable only for slots containing
IMOD cards, when mdlSConfigMismatch=on/on1/on2.
nearEnd - Near End - 1 modem has the correct configuration
farEnd - Far End - 1 has the correct configuration
near…

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.4.2.1.1.1.9

mdlConfigGround

Enables to connect or disconnect an IMOD card to the
ground.
disconnect - not connected to ground.
connect - connected to ground.
notApplicable - for other cards.

Enumeration

.1.3.6.1.4.1.164.3.4.2.1.1.1.10

mdlCapabilities

Indicates the optional capabilities that are implemented by this module
and are manageable through this MIB.
For each capability 1 BIT is allocated in each Octet starting from the LSB.
If the value of the BIT = 1, …

OctetString

.1.3.6.1.4.1.164.3.4.2.1.1.1.11

mdlClockSource

The Clock Source of the Card.
Applicable for ASMi-52 modems only.
internal - means that the card uses its own Internal Clock
external - means that the card uses the Clock received from an
External DTE port …

Enumerationr/w

.1.3.6.1.4.1.164.3.4.2.1.1.1.12

modemParamTable

table

.1.3.6.1.4.1.164.3.4.3.1.1 · 1 row entry · 36 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk modemParamTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::modemParamTable'

This parameters table is applicable mainly for modems that are
not agents.

modemParamEntry row .1.3.6.1.4.1.164.3.4.3.1.1.1

An entry in table.

Indexes

modemIdx

Column Syntax OID

modemIdx

For LRS:
A unique number to identify a modem in the Hub or its
far-end modem.
For DXC:
This will be the ifIndex of the External Port of D8SL card,
that works with this modem/product.
For MP:
This will be the ifIndex of…

SNMPv2-SMIInteger32

Constraints:
range: 0-899

.1.3.6.1.4.1.164.3.4.3.1.1.1.1

modemType

Modem type.
xxxxxx - Stand-Alone modem.
xxxxxxc - Modem on a Card within a Hub having an Agent.
xxxxxxr - Modem on a Card within a Hub having no Agent.
xxxxxxcd - Modem on a Double-Modem Card within a Hub
…

Enumeration

Constraints:
range: 0-96

.1.3.6.1.4.1.164.3.4.3.1.1.1.2

modemConfigMode

The mode identifies if the Modem operates as the Master
unit or as the Slave unit.
For modems having a jumper for this function, this object
will be RO.
This object can be Set only to the Master unit when
mo…

Enumerationr/w

.1.3.6.1.4.1.164.3.4.3.1.1.1.3

modemModeTemporary

This object specifies if the Modem operates as
modemConfigMode value (Master/Slave) temporarily or
permanently.
This object can be Set only when:
- modemConfigMode=master AND modemModeTemporary=no
- modemC…

Enumerationr/w

.1.3.6.1.4.1.164.3.4.3.1.1.1.4

modemNoOfDte

Number of DTE ports in the modem.

SNMPv2-SMIInteger32

Constraints:
range: 1-96

.1.3.6.1.4.1.164.3.4.3.1.1.1.5

modemWire

Modem wiring.

Enumerationr/w

Constraints:
range: 0-101

.1.3.6.1.4.1.164.3.4.3.1.1.1.6

modemMngLink

Communication status between the pair of modems.

Enumeration

Enumerated Values:

1	notApplicable
2	bad
3	mid
4	good
5	unknown
6	syncLoss

.1.3.6.1.4.1.164.3.4.3.1.1.1.7

modemReset

When this object is set to the value of hwReset(3),
the module performs HW Reset.
When this object is set to the value of configReset(4),
the modem performs Configuration Reset, which will set
the modem to the las…

Enumerationr/w

Constraints:
range: 0-101

.1.3.6.1.4.1.164.3.4.3.1.1.1.8

modemSlot

A unique number to identify the slot position of the
modem (card)in its Hub.
notApplicable - for a stand-alone modem or Rack 214
card.
io13..io15 - are for DXC use in case of a Far-Unit that is D8SL ca…

Enumeration

Constraints:
range: 0-101

.1.3.6.1.4.1.164.3.4.3.1.1.1.9

modemHubId

4 Hex characters, identifying the Hub. The last two
characters (least significant) will be displayed on the
Hub's CL card by a 7 segment display.
This object is applicable only for LRS-12 modems.

OctetString

Constraints:
range: 0-101

.1.3.6.1.4.1.164.3.4.3.1.1.1.10

modemIpAddress

For LRS:
The IP address of the LRS-12 agent . If the modem is NOT
an LRS-12 card, the variable will be 0.0.0.0.
For DXC and MP: the IP Address of the Far-End unit.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.4.3.1.1.1.11

modemPsType

The type of PS, for a stand-alone modem.
notApplicable - for LRS-12 or Rack 214 card.

Enumeration

Constraints:
range: 0-1

.1.3.6.1.4.1.164.3.4.3.1.1.1.12

modemMaskTraps

The value determines the modem traps the agent should mask
and not send to the management console.
The value is a sum of 2**n, where n is a bit assigned to a
certain trap. For bit assignment see modem's specification…

SNMPv2-SMIInteger32r/w

Constraints:
range: 0-1

.1.3.6.1.4.1.164.3.4.3.1.1.1.13

modemActiveAlarms

Status of the Alarms for each modem. Each bit represents an
alarm. For bit location of each Alarm in the Octet String
see modem's specification.
A bit is '1' if the alarm is On.
If the value is 0 then there are no…

OctetString

.1.3.6.1.4.1.164.3.4.3.1.1.1.14

modemAlrClear

Setting this attribute to on, clears all the active (On)
alarms of the modem. Upon completion, the value will
automatically change to off(2).

Enumerationr/w

.1.3.6.1.4.1.164.3.4.3.1.1.1.15

modemAlrBufClear

Setting this attribute to on, clears all the alarms in the
buffer alarm of the modem. Upon completion, the value will
automatically change to off(2).

Enumerationr/w

Enumerated Values:

2	nmsSlip
3	terminal
4	agentSlip
5	nmsPpp
6	agentPpp

.1.3.6.1.4.1.164.3.4.3.1.1.1.16

modemMaskSignaling

Mask of Signals per modem. When a signal is masked,
the agent will not send the modemSignalingChange TRAP, upon
change of this signal's value and it will not enter
the History Log.
Each bit represents a signal of t…

OctetStringr/w

Enumerated Values:

1	auto
2	s300bps
3	s1200bps
4	s2400bps
5	s4800bps
6	s9600bps

.1.3.6.1.4.1.164.3.4.3.1.1.1.17

modemPanelType

The panel type of the modem.
This parameter is applicable only for Far-End modems that
are stand-alone or cards of another LRS-12. It enables
displaying the correct panel of the modem.
- Stand-alone : applicable only …

Enumeration

Enumerated Values:

1	dataBits7
2	dataBits8

.1.3.6.1.4.1.164.3.4.3.1.1.1.18

modemIType

Is the modem Intelligent (ASMi-xx) ; or not - (ASM-xx).
This object is used only for the Far-End modem (with the
relevant modemIdx).
notApplicable - for ASMi-32, ASMi-50
no - modem is NOT I-Type so it doesn't have a m…

Enumerationr/w

Enumerated Values:

1	none
2	odd
3	even

.1.3.6.1.4.1.164.3.4.3.1.1.1.19

modemRcvPower

The Rx Level of the modem, in dBm.
Valid values: -99 .. 0.
255=not applicable.

SNMPv2-SMIInteger32

Enumerated Values:

1	dce
2	dte

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.4.3.1.1.1.20

modemSwVersion

SW version of the modem, multiplied by 100.
Example: 115 means SW ver: 1.15
0 = notApplicable.

SNMPv2-SMIInteger32

Enumerated Values:

2	on
3	rts

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.4.3.1.1.1.21

modemLed

OctetString

Enumerated Values:

2	d0
3	d10
4	d50
5	d100
6	d200
7	d300

.1.3.6.1.4.1.164.3.4.3.1.1.1.22

modemRemoteType

Remote modem card type. Not applicable to near - end modems.
For LRS-52, sa(3)=saMaster.

Enumeration

Enumerated Values:

2	on
3	dtr

.1.3.6.1.4.1.164.3.4.3.1.1.1.23

modemConfigPhantom

Enables to supply electric power to remote devices (SA modem,
repeaters), through the current module.
off - remote devices will not get PS through the current modem.
on - remote devices will get PS through the curren…

Enumerationr/w

.1.3.6.1.4.1.164.3.4.3.1.1.1.24

modemRemoteTestEnable

This parameter identifies if the remote Modem allowed to operates
tests.
For Near-End modems this parameter will be ON.

Enumerationr/w

.1.3.6.1.4.1.164.3.4.3.1.1.1.25

modemSwVerString

Display String of the modem SW version.
Format: X. Y Z P
0..9 0..99 A,B,E 0..99
(Z+P are optional.)
A=alpha, B=beta, E=end of development.
Examples: 2.23A8
3.4

SNMPv2-TCDisplayString

Constraints:
range: 4-4

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.4.3.1.1.1.26

modemRemoteIdx

0 = notApplicable.
For LRS:
The Remote modem index.
Applicable only for modemRemoteType=double(5) or quad(7).
For DXC, LRS-52 and MP:
- if Remote unit is an LRS Quad card: remote modem index (1..4)
- if Remote…

SNMPv2-SMIInteger32

Enumerated Values:

2	itu
3	fast
4	s62411

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.4.3.1.1.1.27

modemHwVerString

Display String of the modem HW version.

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.4.3.1.1.1.28

modemResetStatistics

In the on state all statistics counters (including E1
counters) are zeroed. Upon completion, the value will
automatically change to off(2).
notApplicable - for modems with no statistics support.

Enumerationr/w

.1.3.6.1.4.1.164.3.4.3.1.1.1.29

modemMaxRate

Maximum rate supported by the modem

Enumeration

Enumerated Values:

1	unknown
2	len0p133ft
3	len134p266ft
4	len267p399ft
5	len400p533ft
6	len534p655ft
7	fcc68
255	notApplicable

.1.3.6.1.4.1.164.3.4.3.1.1.1.30

modemBoxMaterial

Shape (picture) of modem box is related to box material.
Applicable for ASMi52 SA

Enumeration

.1.3.6.1.4.1.164.3.4.3.1.1.1.31

modemLowSpeed

This parameter enables working at low rates,
when working with a serial interface (V.35,X.21) modem
opposite to a E1/T1 interface modem.

Enumeration

Enumerated Values:

2	disable
3	enable

.1.3.6.1.4.1.164.3.4.3.1.1.1.32

modemDevicePorts

The value indicates the existence of optional ports (which are not Line or DTE).
The value is a sum of 2**n, where n is a bit assigned to a
certain port. For bit assignment see modem's specification.
For ASMi-52 S…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.4.3.1.1.1.33

modemUserName

This object allows the user to configure a name
for the selected modem.

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.4.3.1.1.1.34

modemRowValidity

This parameter defines whether this row is valid or not.
It is an optional parameter.

Enumerationr/w

Constraints:
range: 0-899

.1.3.6.1.4.1.164.3.4.3.1.1.1.35

modemTftpCmd

This parameter defines the TFTP Command.
After performing the command, the Agent will automatically set
this variable to noOp(1).

Enumerationr/w

.1.3.6.1.4.1.164.3.4.3.1.1.1.36

modemAlrBufTable

table

.1.3.6.1.4.1.164.3.4.3.2.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk modemAlrBufTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::modemAlrBufTable'

This parameters table is applicable only for modems that are
not agents.

modemAlrBufEntry row .1.3.6.1.4.1.164.3.4.3.2.1.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
modemAlrBufIdx Running index of the alarm buffer table.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.4.3.2.1.1.1`
modemAlrBufCode The code of the alarm. For text description of each Alarm code see Modem's specification.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.4.3.2.1.1.2`
modemAlrBufState The new status of the alarm.	Enumeration	`.1.3.6.1.4.1.164.3.4.3.2.1.1.3`
modemAlrBufDate The Date at which the alarm has occurred. The format is according to the entered systemDate format.	SNMPv2-TCDisplayString Type Constraints: `range: 0..255` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.164.3.4.3.2.1.1.4`
modemAlrBufTime The time stamp at which the alarm has occurred. The format is hh:mm:ss	SNMPv2-TCDisplayString Type Constraints: `range: 0..255` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.164.3.4.3.2.1.1.5`
modemAlrBufSysUpTime The value of sysUpTime at the time the alarm has occurred. This object is applicable only for products that cannot support calendar date (modemAlrBufDate) and time (modemAlrBufTime) When not applicable, this object con…	RFC1155-SMITimeTicks Constraints: `range: 1-96`	`.1.3.6.1.4.1.164.3.4.3.2.1.1.6`

modemGeneralTable

table

.1.3.6.1.4.1.164.3.4.3.3.1 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk modemGeneralTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::modemGeneralTable'

The IMOD General data Table. The data is specific to each 
modem.

modemGeneralEntry row .1.3.6.1.4.1.164.3.4.3.3.1.1

An entry in the modemGeneralTable. This entry is per modem.
Each modem has a specific index, which identifies it.

Indexes

No indexes recorded

Column	Syntax	OID
modemCurrentElapsedTime The number of seconds that have elapsed since the beginning of the current error-measurement period.	Integer32	`.1.3.6.1.4.1.164.3.4.3.3.1.1.1`
modemValidIntervals The number of previous intervals for which data was collected. The value will be 96 unless the interface was brought on-line within the last 24 hours, in which case the value will be the number of complete 15 minute …	Integer32	`.1.3.6.1.4.1.164.3.4.3.3.1.1.2`

modemIntervalTable

table

.1.3.6.1.4.1.164.3.4.3.3.2 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk modemIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::modemIntervalTable'

The IMOD Interval Table. The data is specific to each 
modem.

modemIntervalEntry row .1.3.6.1.4.1.164.3.4.3.3.2.1

An entry in the modemIntervalTable. This entry is per modem
and per interval selected.

Indexes

No indexes recorded

Column	Syntax	OID
modemIntervalNumber The number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid). Maximum valid number is m…	Integer32 Constraints: `range: 0-100`	`.1.3.6.1.4.1.164.3.4.3.3.2.1.1`
modemSyncLoss Percent of interval, SyncLoss signal is ON. 101 = notApplicable/unknown.	Integer32	`.1.3.6.1.4.1.164.3.4.3.3.2.1.2`
modemLineQuality Quality of Line for the selected modem, in the selected valid interval.	Enumeration	`.1.3.6.1.4.1.164.3.4.3.3.2.1.3`
modemLineUtility Percent of interval, Line is utilized. 101 = notApplicable/unknown.	Integer32	`.1.3.6.1.4.1.164.3.4.3.3.2.1.4`
modemRTS Percent of interval, RTS signal is ON. 101 = notApplicable/unknown.	Integer32 Constraints: `range: 0-96`	`.1.3.6.1.4.1.164.3.4.3.3.2.1.5`
modemCD Percent of interval, CD signal is ON. 101 = notApplicable/unknown.	Integer32	`.1.3.6.1.4.1.164.3.4.3.3.2.1.6`
modemBertResult Result of BERT for the selected modem, in the selected valid interval.	SNMPv2-TCDisplayString Type Constraints: `range: 0..255` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.164.3.4.3.3.2.1.7`
modemBpvError BPV Error. The Octet will be built as follows: MSB 7 6 5 4 3 2 1 0 LSB \|__\| \|______________\| y=0..3 x=0..63 BPV Error = x * (10**y) An Agent that d…	OctetString	`.1.3.6.1.4.1.164.3.4.3.3.2.1.8`
modemFoError FO Error. The Octet will be built as follows: MSB 7 6 5 4 3 2 1 0 LSB \|__\| \|______________\| y=0..3 x=0..63 FO Error = x * (10**y) An Agent that doe…	OctetString	`.1.3.6.1.4.1.164.3.4.3.3.2.1.9`

modmPrtSpTable

table

.1.3.6.1.4.1.164.3.4.4.1.1 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk modmPrtSpTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::modmPrtSpTable'

Configuration parameters of the Local or Remote Modem
Supervisory Ports. The port will be identified by its 
specific ifIndex value.

modmPrtSpEntry row .1.3.6.1.4.1.164.3.4.4.1.1.1

An entry in table.

Indexes

modmPrtHdslIndex

Column Syntax OID

modmPrtSpUsage

This attribute indicates what is the usage of the port.

Enumerationr/w

.1.3.6.1.4.1.164.3.4.4.1.1.1.1

modmPrtSpRate

This attribute indicates the operation rate (speed) of the
port.
auto - automatic rate selection, by the agent.

Enumerationr/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.4.4.1.1.1.2

modmPrtSpDataBits

This attribute indicates the number of data bits in the
word format.

Enumerationr/w

Constraints:
range: 4-4

.1.3.6.1.4.1.164.3.4.4.1.1.1.3

modmPrtSpParity

This attribute indicates the parity mode in async frame

Enumerationr/w

Enumerated Values:

2	off
4	dedicatedTs
5	dedicatedPpp
6	dedicatedFr

.1.3.6.1.4.1.164.3.4.4.1.1.1.4

modmPrtSpInterface

This attribute indicates the supervisory port interface.
dce - the modem appears as a DCE for the SP port.
dte - the modem operates as a DTE, for connection via modem,
for the SP port.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	none
3	proprietary
4	rip2

.1.3.6.1.4.1.164.3.4.4.1.1.1.5

modmPrtSpCTS

CTS line state.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	r4k
3	r8k
4	r12k
5	r16k
6	r32k
7	r64k

.1.3.6.1.4.1.164.3.4.4.1.1.1.6

modmPrtSpDcdDelay

DCD delay in msec.
d10 = delay of 10msec.

Enumerationr/w

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.3.4.4.1.1.1.7

modmPrtSpDsr

DSR line state.

Enumerationr/w

.1.3.6.1.4.1.164.3.4.4.1.1.1.8

modmPrtDs1Table

table

.1.3.6.1.4.1.164.3.4.4.2.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk modmPrtDs1Table

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::modmPrtDs1Table'

Statistics parameters of the Local and Remote modem Ds1 ports.
The port will be identified by its specific ifIndex value.

modmPrtDs1Entry row .1.3.6.1.4.1.164.3.4.4.2.1.1

An entry in table.

Indexes

modmPrtDteIndex

Column Syntax OID

modmPrtDs1HdslPriorityBumpingdeprecated

The 4 bytes represent the 32 time slots of the E1 frame.
Each bit can be set to one, making the corresponding time
slot a HIGH priority. Bits 16 and 32 cannot be modified by the
user. The maximum number of HIGH priority…

OctetStringr/w

.1.3.6.1.4.1.164.3.4.4.2.1.1.1

modmPrtDs1Sync

The standard used for the time required for the E1 port to return
to normal operation after local loss of synchronization. Default:
itu(2).

Enumerationr/w

Enumerated Values:

2	sync
3	async

.1.3.6.1.4.1.164.3.4.4.2.1.1.2

modmPrtDs1BpvLastMin

This object is applicable only for an E1 active port.
It provides the number of BPV (BiPolar Violation) events
detected during the last minute.

SNMPv2-SMIGauge32

Enumerated Values:

1	dataBits6
2	dataBits7
3	dataBits8
4	dataBits9
5	dataBits10
6	dataBits11
7	dataBits5

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.4.4.2.1.1.3

modmPrtDs1BpvMax

This object is applicable only for an E1 active port.
It provides the maximal number of BPV (BiPolar Violation)
events (per minute), detected during the worst minute.

SNMPv2-SMIGauge32

Enumerated Values:

1	stopBits1Bit
2	stopBits1dot5Bits
3	stopBits2Bits

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.4.4.2.1.1.4

modmPrtDs1LineLength

Enumerationr/w

Enumerated Values:

1	r300bps
2	r600bps
3	r1200bps
4	r2400bps
5	r4800bps
6	r9600bps
7	r14400bps
8	r16000bps
9	r19200bps
10	r28800bps
11	r32000bps
12	r38400bps
13	r48000bps
14	r56000bps
15	r57600bps
16	r64000bps
17	r72000bps
18	r96000bps
19	r112000bps
20	r115200bps
21	r128Kbps
22	r144Kbps
23	r192Kbps
24	r256Kbps
25	r320Kbps
26	r384Kbps
27	r448Kbps
28	r512Kbps
29	r576Kbps
30	r640Kbps
31	r704Kbps
32	r768Kbps
33	r1024Kbps
34	r1536Kbps
35	r1544Kbps
36	r2048Kbps
37	e1
38	t1
39	r896Kbps
40	r960Kbps
41	r1152Kbps
42	r1920Kbps
43	r34Mbps
44	r45Mbps
45	r1088Kbps
46	r1216Kbps
47	r1344Kbps
48	r1408Kbps
49	r1472Kbps
50	r1600Kbps
51	r1664Kbps
52	r1728Kbps
53	r1792Kbps
54	r1856Kbps
55	r1984Kbps
56	r1280Kbps
57	r2304Kbps
58	r832Kbps
59	r2176Kbps
60	r2432Kbps
61	r2560Kbps
62	r2688Kbps
63	r2816Kbps
64	r2944Kbps
65	r3072Kbps
66	r3200Kbps
67	r3328Kbps
68	r3456Kbps
69	r3584Kbps
70	r3712Kbps
71	r3840Kbps
72	r3968Kbps
73	r4096Kbps
74	r2112Kbps
75	r2240Kbps
76	r4224Kbps
77	r4352Kbps
78	r4480Kbps
79	r4608Kbps
255	notApplicable

.1.3.6.1.4.1.164.3.4.4.2.1.1.5

modmPrtDs1CRCAvgError

Counts the average number of CRC error events per second.
The average is updated every second

SNMPv2-SMIGauge32

Enumerated Values:

1	d0
2	d1
3	d7
4	d8
5	d10
6	d70
7	disabled
8	enabled
255	notApplicable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.4.4.2.1.1.6

modmPrtDs1DtsToRemote

This attribute indicates whether DTS (Dedicated TS)
is transmitted to remote unit.

Enumerationr/w

Enumerated Values:

1	none
2	odd
3	even

.1.3.6.1.4.1.164.3.4.4.2.1.1.7

modmPrtHdslCurrentTable

table

.1.3.6.1.4.1.164.3.4.4.3.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk modmPrtHdslCurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::modmPrtHdslCurrentTable'

The HDSL Current Table. The data collected is for the current
15-minute interval.

modmPrtHdslCurrentEntry row .1.3.6.1.4.1.164.3.4.4.3.1.1

An entry in the HDSL Current Table. This entry is per HDSL
interface (LOOP1 or LOOP2). Each modem (Central/Remote) has
a specific ifIndex value for the port, which identifies it.
For FDSL it is used for any xDSL interf…

Indexes

No indexes recorded

Column Syntax OID

modmPrtHdslCurrentElapsedTime

The number of seconds that have elapsed since the beginning
of the current error-measurement period.

Integer32

Enumerated Values:

2	disable
3	enable

.1.3.6.1.4.1.164.3.4.4.3.1.1.1

modmPrtHdslCurrentESs

The number of Errored Seconds encountered by an HDSL
interface in the current 15 minute interval. An Errored
Second is any second containing one or more Errored Blocks
or an occurrence of an SDP.

SNMPv2-SMIGauge32

Enumerated Values:

2	disable
3	enable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.4.4.3.1.1.2

modmPrtHdslCurrentSESs

The number of Severely Errored Seconds encountered by an HDSL
interface in the current 15 minute interval. An SES is any
second containing more than 30% Errored Blocks (50 blocks) or
one or more SDPs.

SNMPv2-SMIGauge32

Enumerated Values:

2	disable
3	enable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.4.4.3.1.1.3

modmPrtHdslCurrentBBEs

The number of Background Block Errors encountered by an HDSL
interface in the current 15 minute interval. A BBE is an
errored block not occurring as part of an SES.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.4.4.3.1.1.4

modmPrtHdslCurrentUASs

The number of Unavailable Seconds encountered by an HDSL
interface in the current 15 minute interval. A UAS is any
second in which a failed signal state exists. A failure state
is declared when 10 consecutive SESs oc…

SNMPv2-SMIGauge32

Enumerated Values:

1	none
2	ana
3	rem
4	anaAndBert
5	remAndBert
6	bert
7	twoBerts
8	digital
9	dual
10	clb
11	clbAndBert
12	dteLLB
13	lineRLB

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.4.4.3.1.1.5

modmPrtHdslCurrentNoiseMargin

The current noise margin in DB.
This object is not an accumulative one, therefore
it's value will appear only in this table.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.4.4.3.1.1.6

modmPrtHdslCurrentAttenuation

The current attenuation in DB.
This object is not an accumulative one, therefore
it's value will appear only in this table.

SNMPv2-SMIInteger32

Enumerated Values:

2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.4.4.3.1.1.7

modmPrtHdslIntervalTable

table

.1.3.6.1.4.1.164.3.4.4.3.2 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk modmPrtHdslIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::modmPrtHdslIntervalTable'

The HDSL Interval Table. The data collected is for the last 96
completed 15-minute intervals.

modmPrtHdslIntervalEntry row .1.3.6.1.4.1.164.3.4.4.3.2.1

An entry in the HDSL Interval Table. This entry is per an HDSL
interface (LOOP1 or LOOP2) and per 15 minute interval. The
port and unit (Central/Remote) is identified by its specific
ifIndex value.
For FDSL it is use…

Indexes

No indexes recorded

Column Syntax OID

modmPrtHdslIntervalNumber

The number between 1 and 96, where 1 is the most recently completed
15 minute interval and 96 is the least recently completed 15 minutes
interval (assuming that all 96 intervals are valid).

Integer32

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.4.4.3.2.1.1

modmPrtHdslIntervalESs

The number of Errored Seconds encountered by an HDSL interface in
one of the previous 96, individual 15 minute, intervals.

SNMPv2-SMIGauge32

Enumerated Values:

1	notApplicable
2	off
3	on

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.4.4.3.2.1.2

modmPrtHdslIntervalSESs

The number of Severely Errored Seconds encountered by an HDSL interface in
one of the previous 96, individual 15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.4.4.3.2.1.3

modmPrtHdslIntervalBBEs

The number of Background Block Errors encountered by an HDSL interface in
one of the previous 96, individual 15 minute, intervals.

SNMPv2-SMIGauge32

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.4.4.3.2.1.4

modmPrtHdslIntervalUASs

The number of Unavailable Seconds encountered by an HDSL interface in
one of the previous 96, individual 15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.4.4.3.2.1.5

modmPrtHdslIntervalESR

The ratio of ESs to 900 seconds, encountered by an HDSL interface in
one of the previous 96, individual 15 minute, intervals.

Integer32

.1.3.6.1.4.1.164.3.4.4.3.2.1.6

modmPrtHdslIntervalSESR

The ratio of SESs to 900 seconds, encountered by an HDSL interface in
one of the previous 96, individual 15 minute, intervals.

Integer32

.1.3.6.1.4.1.164.3.4.4.3.2.1.7

modmPrtHdslIntervalBBER

The ratio of BBEs to 900 seconds, encountered by an HDSL interface in
one of the previous 96, individual 15 minute, intervals.

Integer32

Enumerated Values:

1	localExtRemoteRcv
2	localIntRemoteRcv
3	localRcvRemoteInt
4	localRcvRemoteExt
5	localExtAutoRemoteRcv
6	localRcvRemoteExtAuto
7	localSysRemoteRcv
8	localRcvRemoteSys
9	internal
10	external
11	system
12	receive
255	notApplicable

.1.3.6.1.4.1.164.3.4.4.3.2.1.8

modmPrtHdslIntervalValidData

This variable indicates if the data for this interval is valid.

SNMPv2-TCTruthValue

Enumerated Values:

1	n12
2	n9
3	n6
4	n3
5	p0
6	p4
7	p6
8	p10

Description:

Represents a boolean value.

.1.3.6.1.4.1.164.3.4.4.3.2.1.9

modmPrtHdslTotalTable

table

.1.3.6.1.4.1.164.3.4.4.3.3 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk modmPrtHdslTotalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::modmPrtHdslTotalTable'

The HDSL Total Table. The data collected is the cumulative 
sum of the various statistics for the 24 hour period 
preceding the current interval.

modmPrtHdslTotalEntry row .1.3.6.1.4.1.164.3.4.4.3.3.1

An entry in the HDSL Total Table. This entry is per an HDSL
interface (LOOP1 or LOOP2). The port and unit (Central/Remote)
is identified by its specific ifIndex value.
For FDSL it is used for any xDSL interface.

Indexes

No indexes recorded

Column Syntax OID

modmPrtHdslTotalValidIntervals

The number of previous intervals for which valid data was
collected.
The value will be 96 unless the interface was brought on-line
within the last 24 hours, in which case the value will be the
number of complete 15 m…

Integer32

Enumerated Values:

1	infinite
2	i75ohm
3	i100ohm
4	i120ohm
5	i150ohm
6	i300ohm
7	i600ohm

.1.3.6.1.4.1.164.3.4.4.3.3.1.1

modmPrtHdslTotalESs

The number of Errored Seconds encountered by an HDSL
interface in the previous 24 hour interval.

SNMPv2-SMIGauge32

Enumerated Values:

2	off
3	on

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.4.4.3.3.1.2

modmPrtHdslTotalSESs

The number of Severely Errored Seconds encountered by an HDSL
interface in the previous 24 hour interval.

SNMPv2-SMIGauge32

Enumerated Values:

1	private
2	v110
3	v220
4	privateV110Enable
255	notApplicable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.4.4.3.3.1.3

modmPrtHdslTotalBBEs

The number of Background Block Errors encountered by an HDSL
interface in the previous 24 hour interval.

SNMPv2-SMIGauge32

Enumerated Values:

1	notApplicable
2	nm850
3	nm1300
4	nm780Laser
5	nm1300Laser
6	nm1550Laser

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.4.4.3.3.1.4

modmPrtHdslTotalUASs

The number of Unavailable Seconds encountered by an HDSL
interface in the previous 24 hour interval.

SNMPv2-SMIGauge32

Enumerated Values:

1	notApplicable
2	high
3	low

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.4.4.3.3.1.5

modmPrtHdslTable

table

.1.3.6.1.4.1.164.3.4.4.3.4 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk modmPrtHdslTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::modmPrtHdslTable'

The HDSL Table.

modmPrtHdslEntry row .1.3.6.1.4.1.164.3.4.4.3.4.1

An entry in the HDSL Table. The port and unit (Central/Remote)
is identified by its specific modmPrtHdslIndex value.

Indexes

No indexes recorded

Column Syntax OID

modmPrtHdslIndex

The HDSL port index. In some cases it can equal ifIndex.

SNMPv2-SMIInteger32

Enumerated Values:

1	unknown
2	len0p133ft
3	len134p266ft
4	len267p399ft
5	len400p533ft
6	len534p655ft
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.4.4.3.4.1.1

modmPrtHdslDedicatedTs

The HDSL Current Dedicated TS.
Valid values: 0..31.
255 = None (no dedicated TS).

Integer32

Enumerated Values:

1	notApplicable
2	modem1
3	modem2
4	modem3
5	modem4
6	ds1
7	dte

.1.3.6.1.4.1.164.3.4.4.3.4.1.2

modmPrtHdslPriorityBumping

The 4 bytes represent time slots 0..31 of the E1 frame.
Each bit can be set to '1', making the corresponding time slot a HIGH priority.
Bit 0 is always HIGH (cannot be modified by the user).
The maximum number of HIGH p…

OctetStringr/w

Enumerated Values:

1	notApplicable
2	dceExternal
3	dce

.1.3.6.1.4.1.164.3.4.4.3.4.1.3

modmPrtHdslMngProtocol

A unique number to identify an Inband management over the
link.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	dontMask
3	mask

.1.3.6.1.4.1.164.3.4.4.3.4.1.4

modmPrtHdslRoutProtocol

Inband Mng Routing Protocol of the port.
When modmPrtHdslMngProtocol is 'dedicatedPpp'-'proprietary' and
'rip2' are applicable.
For other values - only 'proprietary' is applicabl…

Enumerationr/w

.1.3.6.1.4.1.164.3.4.4.3.4.1.5

modmPrtHdslInbandMngRate

A unique number to identify the rate of the Inband management.
It is applicable only when modmPrtHdslDedicatedTs <> (255 Or 0).

Enumerationr/w

.1.3.6.1.4.1.164.3.4.4.3.4.1.6

modmPrtHdslPriorityBumpingEnable

This attribute indicates the Priority Bumping Mode.
It is relevant only for 4W interfaces.

Enumerationr/w

Enumerated Values:

1	local
2	remote

.1.3.6.1.4.1.164.3.4.4.3.4.1.7

modmPrtHdslPriorityBumpingTimeout

This attribute indicates the Priority Bumping Timeout in minutes.
It is relevant only for 4W interfaces (2 lines of 2W each).
Upon failure of one of the 2W lines,
Timeout is the time period that the agent should wait
un…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.4.4.3.4.1.8

modmPrtDteTable

table

.1.3.6.1.4.1.164.3.4.4.4.1 · 1 row entry · 22 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk modmPrtDteTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::modmPrtDteTable'

Configuration parameters of the Master and Slave Modem DTE 
Ports. The port and unit (Master/Slave) is identified by 
its specific modmPrtDteIndex value.

modmPrtDteEntry row .1.3.6.1.4.1.164.3.4.4.4.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

modmPrtDteIndex

The DTE port index.

SNMPv2-SMIInteger32

Enumerated Values:

1	unknown
3	fault
4	active
6	none

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.4.4.4.1.1.1

modmPrtDteProtocol

The DTE port Protocol.

Enumerationr/w

.1.3.6.1.4.1.164.3.4.4.4.1.1.2

modmPrtDteDataBits

The DTE number of data bits.

Enumerationr/w

Enumerated Values:

1	autoredundancy
5	main
6	back

.1.3.6.1.4.1.164.3.4.4.4.1.1.3

modmPrtDteStopBits

The DTE minimum number of stop bits in the tx async frame.

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.3.4.4.4.1.1.4

modmPrtDteRate

The DTE port rate.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	localInternal
3	localExternal
4	loopTiming
5	transparent

.1.3.6.1.4.1.164.3.4.4.4.1.1.5

modmPrtDteCtsDelay

CTS/RTS delay, in msec.
dxx = xx msec.
notApplicable - for ASMi-31, ASMi-32.

Enumerationr/w

Enumerated Values:

2	available
3	notAvailable

.1.3.6.1.4.1.164.3.4.4.4.1.1.6

modmPrtDteParity

This attribute indicates the parity mode in async frame.

Enumerationr/w

Enumerated Values:

2	off
3	auto
4	manual
6	forcedBU
7	autoNonRevertive

.1.3.6.1.4.1.164.3.4.4.4.1.1.7

modmPrtDteIfType

The interface type of the DTE port.

Enumeration

Enumerated Values:

1	unknown
2	optimux4Sa
3	optimux4Card
4	fomiE3T3Sa
5	fomiE3T3Card
6	optimuxXL16
7	optimuxXLE1
8	optimux4E1L
9	optimux4T1L
10	optimuxXLT1
11	op16E1L
12	op16E1LS
13	opXLE1
14	opXLT1
15	opXL16E1
16	op4E1
17	op4T1
18	fdsl101
19	fdsl201
20	op4E1LNew
21	op4T1LNew
22	op34E1
23	op4E1Mar06
24	op4E1NG1
25	op4T1NG1
26	op25
255	notApplicable

.1.3.6.1.4.1.164.3.4.4.4.1.1.8

modmPrtDteRlbEnable

Enable/Disable Remote Loop-Back on this modem, externally
initiated.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disabled
3	enabled

.1.3.6.1.4.1.164.3.4.4.4.1.1.9

modmPrtDteAlbEnable

Enable/Disable Analog Loop-Back on this modem, externally
initiated.

Enumerationr/w

.1.3.6.1.4.1.164.3.4.4.4.1.1.10

modmPrtDteRtsDcdEnable

Enable/Disable RTS-DCD.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.4.4.4.1.1.11

modmPrtDteDsrDtrEnable

Enable/Disable DSR-DTR.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.4.4.4.1.1.12

modmPrtDteSignaling

Each bit represents a specific signal state.
1 - means : signal is ON , Enabled, Yes (exists)
0 - means : signal is OFF, Disabled, No .
For detailed bit assignment see product's spec.

OctetString

Enumerated Values:

1	notApplicable
2	noDivision
3	half
4	quarter

.1.3.6.1.4.1.164.3.4.4.4.1.1.13

modmPrtDteLoops

Loops that can be run on the DTE port.
none - no loop (stop running loop)
ana - Local Analog Line loop
rem - Remote Analog Line loop
anaAndBert - ana & BERT together
remAndBert - rem & BERT together
bert …

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.3.4.4.4.1.1.14

modmPrtDteTests

This is a mask which indicates
- for Get: which tests are running on the DTE port.
- for Set: tests the user wishes to start or stop.
Each test has its specific bit.
- '1' means the test runs (Set: should run).
- '0' …

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.4.4.4.1.1.15

modmPrtDteClearAllTests

Setting this attribute to on, clears all the running loops
and tests of the DTE port. Upon completion, the value will
automatically change to off(2).

Enumerationr/w

Enumerated Values:

1	notApplicable
2	off
3	on

.1.3.6.1.4.1.164.3.4.4.4.1.1.16

modmPrtDteBertResult

Result of BERT for the selected DTE port.
Applicable only if BERT is running on the DTE port.

SNMPv2-TCDisplayString

Enumerated Values:

1	notApplicable
2	t1
3	e1

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.4.4.4.1.1.17

modmPrtDteErrCorrect

notApplicable - for modems that do not support this object
on - will start a random error correction process.
onBurst - will start a burst error correction process.
Setting this object to 'off', will stop any k…

Enumerationr/w

.1.3.6.1.4.1.164.3.4.4.4.1.1.18

modmPrtDteV54DigitalTest

Enables to start a remote digital loopback upon recognition of a special pattern.
disable - will not start a digital loopback when a special pattern is
recognized.
enable - will start a loopback upon recognition of a …

Enumerationr/w

Enumerated Values:

1	notApplicable
2	noEnforcement
3	main
4	backup

.1.3.6.1.4.1.164.3.4.4.4.1.1.19

modmPrtDteV54DigitalTestStatus

Indicates whether a remote digital test was triggered by a pattern
by the remote modem or not.
no - the digital test wasn't triggered by a pattern by the remote modem.
yes - the digital test was triggered by a pattern …

Enumeration

.1.3.6.1.4.1.164.3.4.4.4.1.1.20

modmPrtDteTestTimeOut

Indicates the timeout for LLB test.
0=Forever

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.4.4.4.1.1.21

modmPrtDteAlarmForwarding

This MIB object defines whether to enable or disable Alarm Forwarding for this port.
It means whether this port will be affected by the failure of its respective Line port.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	notExist
3	exist

.1.3.6.1.4.1.164.3.4.4.4.1.1.22

modmPrtLineTable

table

.1.3.6.1.4.1.164.3.4.4.5.1 · 1 row entry · 16 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk modmPrtLineTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::modmPrtLineTable'

Configuration parameters of the Master and Slave Modem Line 
Ports. The port and unit (Master/Slave) is identified by 
its specific modmPrtLineIndex value.

modmPrtLineEntry row .1.3.6.1.4.1.164.3.4.4.5.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

modmPrtLineIndex

The Line port index.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.4.4.5.1.1.1

modmPrtLineClkSrc

The clock source of the Line port.
(5),(6) - applicable only for ASMi-24 and ASMi-50.
(7),(8) - System level Clock Source. Applicable to CQ modems.

Enumerationr/w

Enumerated Values:

1	local
2	remote

.1.3.6.1.4.1.164.3.4.4.5.1.1.2

modmPrtLineTxLevel

Transmit level in dBm.
pxx = positive xx = +xx
nxx = negative xx = -xx

Enumerationr/w

.1.3.6.1.4.1.164.3.4.4.5.1.1.3

modmPrtLineRxLevel

Rx Sensitivity in dBm.
pxx = positive xx = +xx
nxx = negative xx = -xx.

Enumerationr/w

Enumerated Values:

1	unknown
2	noModule
3	e3linkCX34
4	e3linkOPT1
5	t3linkOPT1
6	eth1Port
7	e1FourUTP
8	e1TwoPort
9	e1TwoUB
10	t1FourPort
11	t1TwoPort
12	e1FourRJ45
13	e1FourBNC
14	e1FourMiniBNC
15	sfLink
16	stationClk
17	hssi
18	stationClkT3
19	t3linkCX45
20	hs4
21	hs2
22	hs1
23	hs1x8M
24	fastEth
25	nX64
26	nX64AndUnbalanced2E1
27	nX64AndBalanced2E1
28	nX64T1
29	nX64T1AndUnbalanced2T1
30	nX64T1AndBalanced2T1
31	ds1channels
32	op155Fiber
33	op155SingleFiber
34	op155coax
35	op63e1
36	op84t1
37	op155Ds3Cl
38	ds1channelsUnbalanced
39	fastEthNew
40	op2128e1t1
41	op4256e1t1
42	fans
43	t1FourRJ45
44	e1Four2BNC

.1.3.6.1.4.1.164.3.4.4.5.1.1.4

modmPrtLineOutImp

Output impedance in Ohm.

Enumerationr/w

.1.3.6.1.4.1.164.3.4.4.5.1.1.5

modmPrtLineInImp

Input impedance in Ohm.

Enumerationr/w

.1.3.6.1.4.1.164.3.4.4.5.1.1.6

modmPrtLineCarrCntrl

Carrier control.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	nm850
3	nm1300
4	nm1300Laser
5	nm1550Laser

.1.3.6.1.4.1.164.3.4.4.5.1.1.7

modmPrtLineRAP

Rate Adapting Protocol.
privateV110Enable (4)= private but enables return to v110.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	internal
3	external
4	lbt

.1.3.6.1.4.1.164.3.4.4.5.1.1.8

modmPrtLineWaveLength

Wave Length of the optical Line.
notApplicable - when the modem Line is not optical.
The units are nano-meters [nm].

Enumeration

.1.3.6.1.4.1.164.3.4.4.5.1.1.9

modmPrtLineCdSense

Carrier Detect Sense - Detection Sensitivity of Carrier Wave.
high - high sensitivity
low - low sensitivity.

Enumerationr/w

.1.3.6.1.4.1.164.3.4.4.5.1.1.10

modmPrtLineAIS

AIS enable/disable.
notApplicable - for modems that do not support this feature.

Enumerationr/w

.1.3.6.1.4.1.164.3.4.4.5.1.1.11

modmPrtLineCoding

Line Coding.

Enumerationr/w

.1.3.6.1.4.1.164.3.4.4.5.1.1.12

modmPrtLineLength

This attribute is the line length mask parameter used only
for T1/DSU interfaces.
len400p533ft=length range: 400ft to 533ft.

Enumerationr/w

.1.3.6.1.4.1.164.3.4.4.5.1.1.13

modmPrtLineClkSrcPort

Clock Source Port.
This parameter is relevant for external clock source.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	e1
3	t1

.1.3.6.1.4.1.164.3.4.4.5.1.1.14

modmPrtLineDteClkConfig

Indicates the clock source of the modems, which were not selected to supply
the external clock.

Enumerationr/w

.1.3.6.1.4.1.164.3.4.4.5.1.1.15

modmPrtLineMaskAlr

This parameter determine whether masking or not the alarms for this line.

Enumerationr/w

.1.3.6.1.4.1.164.3.4.4.5.1.1.16

optMxConfigTable

table

.1.3.6.1.4.1.164.3.5.1 · 1 row entry · 27 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk optMxConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::optMxConfigTable'

This table contains parameters of configuration
for each member of the couple of Optimux.

optMxConfigEntry row .1.3.6.1.4.1.164.3.5.1.1

An entry in the Optimux Config table.

Indexes

No indexes recorded

Column Syntax OID

optIndex

optIndex = 1 is for local Optimux.
optIndex = 2 is for remote Optimux.

Enumeration

.1.3.6.1.4.1.164.3.5.1.1.1

optHWVersion

HW Version of the device.

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.5.1.1.2

optSWVersion

SW Version of the device.

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.5.1.1.3

optPSPrimary

The status of the primary Power Supply Unit.

Enumeration

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.5.1.1.4

optPSSecondary

The status of the secondary Power Supply Unit.

Enumeration

Enumerated Values:

1	notApplicable
2	short
3	long

.1.3.6.1.4.1.164.3.5.1.1.5

optLinkActive

This object indicates which link is active.
For Optimux-4 it may be: 5, 6 or 105, 106
For FOMi-E3/T3 it may be: 51, 61 or 151, 161.
For Optimux-T3 it may be: 51 or 61.
For Optimux-155/1 refer to product spec.

IF-MIBInterfaceIndex

Enumerated Values:

2	single
3	redundancy
4	dualLink
5	priorityBumping
6	switchBackup

Type Constraints:
range: 1..2147483647

Description:

.1.3.6.1.4.1.164.3.5.1.1.6

optSelectLink

This object is used by Optimuxes.
- For Optimux 4E1/T1 Old Look:
This MIB object enables the user to force the device to use specific link.
autoredundancy= Main (Link 1) is the default link. When it will fail, the
…

Enumerationr/w

Enumerated Values:

2	auto
3	manual

.1.3.6.1.4.1.164.3.5.1.1.7

optGrpPayLoadLoop

Performs payload loop ( remote loop) to 4 E1 channels
at once.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	auto
3	manual

.1.3.6.1.4.1.164.3.5.1.1.8

optGrpClockSource

For Optimux XL:
If dsx3TransmitClockSource = localTiming(2), then the user
can configure this field as:
localInternal(2) = use the internal clock of the device
localExternal(3) = use the external clock connected to the …

Enumerationr/w

Enumerated Values:

1	none
103	kmxMlA
104	kmxMlB

.1.3.6.1.4.1.164.3.5.1.1.9

optRedundancyStatus

If there are two modules 'links', then this field
should be set to available(2). If there is only one
module 'link', this field should be set to notAvailable(3).

Enumeration

.1.3.6.1.4.1.164.3.5.1.1.10

optRedundancyCnf

This object is used by Optimux-XL, FomiE3/T3, Optimux-T3 and Optimux-155.
For Optimux-XL:
If optRedundancyStatus = notAvailable(3), then this field
can be off(2) or forcedBU(6).
- off(2) = forcedMain: forces the…

Enumerationr/w

.1.3.6.1.4.1.164.3.5.1.1.11

optFarEndType

Far-End type of product.
This object is especially relevant for the local optimux.
notApplicable - for devices that don't have a far-end unit.

Enumeration

.1.3.6.1.4.1.164.3.5.1.1.12

optServiceChEnable

Service Channel Enable/Disable for each Optimux (local/remote).

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disabled
3	enabled

.1.3.6.1.4.1.164.3.5.1.1.13

optMaskChAlr

Mask Channel Alarm.
This object is applicable only for Optimux cards.
The value of this object is a sum of 2**n, where n is a bit assigned to
a certain Channel. Bit='1' means masked.
For Optimux-4:
Bit0: CH1 ; Bi…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	automatically
3	manually

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.5.1.1.14

optAisEnable

AIS enable/disable.
notApplicable - for devices that do not support this feature.

Enumerationr/w

.1.3.6.1.4.1.164.3.5.1.1.15

optFarMng

This object is used by Optimux-XL and FomiE3/T3.
Is there possibility of Far-End Management (no/yes).
This object is applicable only for the Local device.
notApplicable - for Remote device and devices that do not suppor…

Enumerationr/w

.1.3.6.1.4.1.164.3.5.1.1.16

optClockDivision

This object is applicable only for FomiE3/T3 having an HSSI Electrical
interface.
It gives the possibility of Clock Division, so that Clock Rate will
be less than T3/E3.
notApplicable - for a device that does not suppor…

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.5.1.1.17

optDteLoopEnable

DTE Loop enable/disable (for example loop command requested
by router).
This object is applicable only for products having HSSI interface.
notApplicable - for devices that do not support this feature.

Enumerationr/w

Enumerated Values:

2	onLine
3	alternate

.1.3.6.1.4.1.164.3.5.1.1.18

optGrpClockSourcePrt

This object is applicable for Optimux-T3, when optGrpClockSource=localExternal.
It enables the user to select the Channel or Station Clock from which
the Clock is received.
Valid values:
0 = notApplicable
1..28 (= CH1.…

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	isdn
3	pstn

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.5.1.1.19

optIncomingAlarm

State of the Incoming Alarm (On/Off), via Alarm Relay connector.
This object is applicable only for Optimux-T3.

Enumeration

Enumerated Values:

2	sec30
3	sec45
4	sec60
5	sec120

.1.3.6.1.4.1.164.3.5.1.1.20

optDefChannelSet

Default configuration for all Optimux Channels: T1 or E1.
This object is applicable only for Optimux-T3.

Enumerationr/w

Enumerated Values:

2	noBackup
3	line
4	path

.1.3.6.1.4.1.164.3.5.1.1.21

optWaitToRestore

This parameter defines the time (sec) device has to wait in the redundant
state until it goes back to the default Link.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.5.1.1.22

optEnforcedLink

This parameter is not applicable when optRedundancyCnf = off.
It enables user to enforce a Link in spite of the redundancy mechanism.
Selecting the noEnforcement(2) value cause return to the usual rules of the
redundan…

Enumerationr/w

.1.3.6.1.4.1.164.3.5.1.1.23

optFlipUponEvent

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	active
255	temporary

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.5.1.1.24

optHwMaskChAlr

Mask Channel Alarm done by the HW dip-switches.
This object is applicable only for Optimux cards.
The value of this object is a sum of 2**n, where n is a bit assigned to
a certain Channel.
For Optimux-16E1:
Bit0: …

SNMPv2-SMIInteger32

Enumerated Values:

1	sunday
2	monday
3	tuesday
4	wednesday
5	thursday
6	friday
7	saturday

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.5.1.1.25

optServiceChExist

Service Channel Existence indication for each Optimux (local/remote).

Enumeration

Enumerated Values:

1	zone1
2	zone2
3	zone3
4	zone4
5	zone5

.1.3.6.1.4.1.164.3.5.1.1.26

optMaskSystemAlr

Mask all system alarms for each Optimux (local/remote).

Enumerationr/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.3.5.1.1.27

optMxModuleTable

table

.1.3.6.1.4.1.164.3.5.2 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk optMxModuleTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::optMxModuleTable'

This table defines the type of the module
enrolled in each slot.

optMxModuleEntry row .1.3.6.1.4.1.164.3.5.2.1

An entry in the Optimux Module table.

Indexes

No indexes recorded

Column Syntax OID

optMdIdx

optMdIdx = 1 is for local Optimux.
optMdIdx = 2 is for remote Optimux.

Enumeration

.1.3.6.1.4.1.164.3.5.2.1.1

optMdSltIdx

For Optimux XL:
Slot A = 1, Slot B = 2, Slot C = 3, Slot D = 4,
Slot Link = 5, Slot BU = 6 .
For FomiE3/R3:
Slot of Station Clock = 3, Slot of Electrical Link = 4,
Slot of Optical Main Link = 5, Slot of Optical Backup L…

SNMPv2-SMIInteger32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.5.2.1.2

optMdType

Module Type and number of connectors.

Enumeration

Enumerated Values:

103	kmxMlA
104	kmxMlB

.1.3.6.1.4.1.164.3.5.2.1.3

optMdHWVersion

HW Version of the module.

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.5.2.1.4

optMdModLed

The meaning of each bit depends on the module type.

OctetString

Constraints:
range: 0-239

.1.3.6.1.4.1.164.3.5.2.1.5

optMdWaveLength

Wave Length of T3/E3 Optical Links in [nm] and specification if Laser or not.

Enumeration

Constraints:
range: 0-239

.1.3.6.1.4.1.164.3.5.2.1.6

optMdTimingMode

The Module Timing mode.

Enumerationr/w

.1.3.6.1.4.1.164.3.5.2.1.7

optMdStatusIndication

Indication of Alarm and test status of
all interfaces served by a module.

For Optimux155, Each interface will be represented by 2
bits where the 1st bit (right) will specify alarm status
and t…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.5.2.1.8

optFramerPortTable

table

.1.3.6.1.4.1.164.3.5.3.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk optFramerPortTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::optFramerPortTable'

This table defines the connection of every ch of the framer.

optFramerPortEntry row .1.3.6.1.4.1.164.3.5.3.1.1

An entry in the Optimux Framer port Connections table.

Indexes

No indexes recorded

Column	Syntax	OID
optFramerPortIdx The channel of the Framer. Valid values:1..31.	SNMPv2-SMIInteger32 Constraints: `range: 1-31`	`.1.3.6.1.4.1.164.3.5.3.1.1.1`
optFramerPortConn This parameter defines the Framer channel connection. The values will be as follows: Loop(1),Ch1(2),Ch2(3)....,Ch28(29).	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.5.3.1.1.2`
optFramerPortType This parameter defines the Framer port (E1 or T1).	Enumerationr/w	`.1.3.6.1.4.1.164.3.5.3.1.1.3`
optFramerPortFeIpAddr The IP Address of the opposite optimux in the ring,which this channel connected to.	RFC1155-SMIIpAddressr/w Type Constraints: `range: 4`	`.1.3.6.1.4.1.164.3.5.3.1.1.4`

optRingNeTable

table

.1.3.6.1.4.1.164.3.5.3.4 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk optRingNeTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::optRingNeTable'

This table defines which optimuxes are in the ring and the 
IP Address of each one.

optRingNeEntry row .1.3.6.1.4.1.164.3.5.3.4.1

An entry in the Optimux Ring Connections table.

Indexes

No indexes recorded

Column Syntax OID

optRingNeIdx

The index of the optimux, starting with next optimux to the current optimux.
Valid values:1..28.
The index is according to the order of optimux connections in the ring.
Example:
1=next optimux to the current, in the r…

SNMPv2-SMIInteger32

Enumerated Values:

101	kmxPsA
102	kmxPsB
103	kmxMlA
104	kmxMlB
105	kmxCl
106	kmxOpt
107	kmxIO1
108	kmxIO2
109	kmxIO3
110	kmxIO4
111	kmxIO5
112	kmxIO6
113	kmxIO7
114	kmxIO8
115	kmxIO9
116	kmxIO10
117	kmxIO11
118	kmxIO12

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.5.3.4.1.1

optRingNeIpAddr

The IP Address of each optimux in the ring, according to optRingNeIdx.

RFC1155-SMIIpAddress

Enumerated Values:

1	notApplicable
103	kmxMlA
104	kmxMlB
119	kmxMlAandMlB

Type Constraints:
range: 4

.1.3.6.1.4.1.164.3.5.3.4.1.2

sysGenKmuxTable

table

.1.3.6.1.4.1.164.3.6.1.1.1 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sysGenKmuxTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sysGenKmuxTable'

A table containing the general Kmux parameters.

sysGenKmuxEntry row .1.3.6.1.4.1.164.3.6.1.1.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

sysGenConfigIdx

This object indicates the Configuration number (1..255)
referred.
Value of 255 specifies the TmpCnfg (Scratch).
The write operation in this Table is valid only to the
TmpCnfg entry.

Integer32

Enumerated Values:

1	notApplicable
2	idleBusy
3	forcedIdle
4	busyIdle
5	forcedBusy

.1.3.6.1.4.1.164.3.6.1.1.1.1.1

sysGenFlipIntegration

The parameter is relevant only for KM-2100 and only when
sysGenMlMode=redundancy, switchBackup, or priorityBumping.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	dceDce
3	dceDte
4	dteDce
5	dteDte

.1.3.6.1.4.1.164.3.6.1.1.1.1.2

sysGenMlMode

The Main Link operation mode. Determines how many links are
used (one/two) and how they are used.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	lt
3	nt
4	te

.1.3.6.1.4.1.164.3.6.1.1.1.1.3

sysGenFaType

Frame Allocation type:
auto - automatic frame allocation (by Kmux)
manual - manually configured frame allocation (by user).

Enumerationr/w

.1.3.6.1.4.1.164.3.6.1.1.1.1.4

sysGenLinkRecovery

The parameter determines the Link Recovery mode.
The parameter is relevant only when the sysGenMlMode is either
switchBackup or priorityBumping.

Enumerationr/w

Enumerated Values:

1	noCallIndicator
2	dialing
3	connected
4	disconnecting
5	disconnected

.1.3.6.1.4.1.164.3.6.1.1.1.1.5

sysGenLinkSourceClock

The source clock for the links. The parameter is relevant
only for KM-2100 having a KDI or KDI/CH cards. ML-A or ML-B
are selectable only when sysGenMlMode=dual or priorityBumping.

Enumerationr/w

Enumerated Values:

2	disconnected
3	connected

.1.3.6.1.4.1.164.3.6.1.1.1.1.6

sysGenMngBwA

The required management rate for ML-A, in bps. It is very important when a remote
unit is managed.
The selected value must be < ML-A Rate value.
0 = None or not applicable
800 bps = minimum value
19200 bps = maximum…

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	disconnected
3	connected

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.1.1.1.1.7

sysGenMngBwB

The required management rate for ML-B, in bps. It is very important when a remote
unit is managed.
The selected value must be < ML-B Rate value.
0 = None or not applicable
800 bps = minimum value
19200 bps = maximum…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.1.1.1.1.8

sysGenAutoDialSlot

This object indicates the IO-SLOTs that can be used to initiate Automatic
DialUp.
This field will be applicable when KML.10 is a ML and its
prtIsdnSwitchMode=auto.
Each IO Slot is represented by a bit: 11 ...........…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.1.1.1.1.9

sysGenResetBypassEnable

Enable/Disable Reset Bypass operation when a KDI card exists
and one of its links failed.
notApplicable - when no KDI card exists in the Hub.

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.6.1.1.1.1.10

sysGenRebuildFrame

How to rebuild frame (when a CH is connected/disconnected):
automatically - immediately, by automatic frame allocation (by Kmux)
manually - manually configured frame allocation (by user), or Rebuild
Frame command to ML…

Enumerationr/w

Enumerated Values:

107	kmxIO1
108	kmxIO2
109	kmxIO3
110	kmxIO4
111	kmxIO5
112	kmxIO6
113	kmxIO7
114	kmxIO8
115	kmxIO9
116	kmxIO10
117	kmxIO11
118	kmxIO12

.1.3.6.1.4.1.164.3.6.1.1.1.1.11

sysBackupTable

table

.1.3.6.1.4.1.164.3.6.1.3.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sysBackupTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sysBackupTable'

A table containing the backup parameters.

sysBackupEntry row .1.3.6.1.4.1.164.3.6.1.3.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

sysBackupConfigIdx

This object indicates the Configuration number (1..255)
referred.
Value of 255 specifies the TmpCnfg (Scratch).

Integer32

Enumerated Values:

2	s1s2s3s4
3	s5s6s7s8
4	s9s10s11s12
5	s13s14s15s16
6	s17s18s19s20
7	s21s22s23s24
8	s13s14s15s17
9	s18s19s20s21
10	s22s23s24s25
11	s26s27s28s29
12	s30s31

.1.3.6.1.4.1.164.3.6.1.3.1.1.1

sysBackupDatabase

Determines the database to switch to, when ML recovery occurs.

Enumerationr/w

.1.3.6.1.4.1.164.3.6.1.3.1.1.2

sysBackupMode

isdn - for connection to ISDN network.
pstn - for connection to PSTN network.

Enumerationr/w

Enumerated Values:

2	notSupported
3	forcedIdle
4	forcedBusy

.1.3.6.1.4.1.164.3.6.1.3.1.1.3

sysBackupDialTimeout

The dial timeout in seconds (when backup is attempted).

Enumerationr/w

Enumerated Values:

1	notApplicable
2	a
3	b
4	aANDb
5	crossAandB
6	ccs
7	aEqualsB

.1.3.6.1.4.1.164.3.6.1.3.1.1.4

sysBackupOptions

The Backup options:
noBackup - No backup is applicable
line - Line Data backup
path - Line Mng backup .

Enumerationr/w

Enumerated Values:

1	notApplicable
2	a
3	b
4	aANDb
6	ccs

.1.3.6.1.4.1.164.3.6.1.3.1.1.5

sysBackupAgendaTable

table

.1.3.6.1.4.1.164.3.6.1.3.2 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sysBackupAgendaTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sysBackupAgendaTable'

A table containing the backup schedule. It is possible to
define 4 different time zone schedules per day of the week.

sysBackupAgendaEntry row .1.3.6.1.4.1.164.3.6.1.3.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

sysBackupCfgIdx

This object indicates the Configuration number (1,255)
referred.
Write operation for the table entries is allowed only to
the temporary configuration (255).

Enumeration

Enumerated Values:

1	notConnected
2	bps4800
3	bps6400
4	bps9600
5	bps12800
6	bps16000
7	bps19200
8	bps32000
9	bps64000

.1.3.6.1.4.1.164.3.6.1.3.2.1.1

sysBackupDay

Day of the week.

Enumeration

.1.3.6.1.4.1.164.3.6.1.3.2.1.2

sysBackupZone

The time zone.

Enumeration

Enumerated Values:

1	notApplicable
2	crc16
3	crc32

.1.3.6.1.4.1.164.3.6.1.3.2.1.3

sysBackupEndTime

The end time for this time zone. The format is HH:MM. For
example 23:59.
For Zone 4, End Time = 23:59 (constant).

OctetStringr/w

.1.3.6.1.4.1.164.3.6.1.3.2.1.4

sysBackupStatus

Enable or disable this backup schedule entry.

Enumerationr/w

.1.3.6.1.4.1.164.3.6.1.3.2.1.5

sysFrameAllocationTable

table

.1.3.6.1.4.1.164.3.6.1.4.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sysFrameAllocationTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sysFrameAllocationTable'

A table for manually configuring the frame allocation.
The table will contain always all the programmed cards' 
ports. sysFaNumOfBits

sysFrameAllocationEntry row .1.3.6.1.4.1.164.3.6.1.4.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

sysFaConfigIdx

This object indicates the Configuration number (1..255)
referred.
Value of 255 specifies the TmpCnfg (Scratch).
Write operation for the table entries is allowed only to
Config=255.

Integer32

Enumerated Values:

1	disable
2	remoteDisconnect
3	remoteDisconnectAndSilence
4	silenceOnly
5	fastBusyOnly
6	silenceOrFastBusy

.1.3.6.1.4.1.164.3.6.1.4.1.1.1

sysFaLink

The main link on which frame allocation is done.

Enumeration

Enumerated Values:

1	notApplicable
2	remote
3	local

.1.3.6.1.4.1.164.3.6.1.4.1.1.2

sysFaPrt

The Frame Allocation (FA) port.
The ports will be specified by:
Slot*100+Ch.
- for Bypass of KDI or KDI/CH the port will be:
Slot*100+11 (internal-1=non-existent port ; just for use
of the same MI…

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	reportOnly
3	disconnect

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.1.4.1.1.3

sysFaStartingBit

The data starting bit for the channel.
- for Bypass of KDI or KDI/CH, this will be the Starting Bit
of the Bypass Window on the specific sysFaLink.
- for Control Signals of a card ( sysFaPrt=Slot*100+0)
this will …

Integer32r/w

.1.3.6.1.4.1.164.3.6.1.4.1.1.4

sysFaNumOfBits

The data size in number of bits for the channel.
- for Bypass of KDI or KDI/CH, this will be the Bypass Window
size. In this case, this value must be the same for both
MLs.
- for Control Signals of a card ( sysFaP…

Integer32r/w

.1.3.6.1.4.1.164.3.6.1.4.1.1.5

sysDisconnectSupervisionEventTable

table

.1.3.6.1.4.1.164.3.6.1.5 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sysDisconnectSupervisionEventTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sysDisconnectSupervisionEventTable'

Disconnect Supervision Event table.

sysDisconnectSupervisionEventEntry row .1.3.6.1.4.1.164.3.6.1.5.1

An entry in the table.

Indexes

No indexes recorded

Column	Syntax	OID
sysDsEventIdx This object indicates a unique Event Index.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.3.6.1.5.1.1`
sysDsEventSlot This object indicates a unique number of the slot position, where the KVF.6 or KVF.8 card is inserted, and the Disconnect Supervision Event occurred.	Enumeration	`.1.3.6.1.4.1.164.3.6.1.5.1.2`
sysDsEventTS This object defines the Time Slot number, where the Disconnect Supervision Event occurred.	Integer32	`.1.3.6.1.4.1.164.3.6.1.5.1.3`
sysDsEventDescr This object defines the Description of the Disconnect Supervision Event.	SNMPv2-TCDisplayString Type Constraints: `range: 0..255` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.164.3.6.1.5.1.4`
sysDsEventDateAndTime This object defines the Date and Time, when the Disconnect Supervision Event occurred. It will be displayed in the following format: YYYY-MM-DD HH:MM:SS.	SNMPv2-TCDisplayString Type Constraints: `range: 0..255` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.164.3.6.1.5.1.5`

mdlKmxTable

table

.1.3.6.1.4.1.164.3.6.2.2 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlKmxTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlKmxTable'

A table.

mdlKmxEntry row .1.3.6.1.4.1.164.3.6.2.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

mdlKmxConfigIdx

This object indicates the Configuration number (1..255)
referred.
Value of 255 specifies the TmpCnfg (Scratch).
Write operation for the table entries is allowed only to
Config=255.

Integer32

.1.3.6.1.4.1.164.3.6.2.2.1.1

mdlKmxSlotIdx

This object indicates a unique number of the slot position
in which the module is inserted.

Enumeration

.1.3.6.1.4.1.164.3.6.2.2.1.2

mdlKmxOperatedMl

The main link for this card.
The field is relevant only for ML modes of Dual, Priority
Bumping and Switched Backup.

Enumerationr/w

.1.3.6.1.4.1.164.3.6.2.2.1.3

mdlKmxMlAtoMlBPrio

ML-A to ML-B Priority.
The field is relevant only for ML modes of Priority Bumping
and Switched Backup.

Enumerationr/w

.1.3.6.1.4.1.164.3.6.2.2.1.4

mdlKmxMlBtoMlAPrio

ML-B to ML-A Priority.
The field is relevant only for ML modes of Priority Bumping.

Enumerationr/w

Enumerated Values:

103	kmxMlA
104	kmxMlB

.1.3.6.1.4.1.164.3.6.2.2.1.5

mdlKmxOutSrvMethod

Out of service method. For KVC.1 and KVC.1M all values are
applicable.
For KVC.2, KVC.3, KVF.1, KVF.3, KVF.4: only forcedIdle and
forcedBusy are applicable.

Enumerationr/w

Enumerated Values:

1	bps400
2	bps800
3	bps1600
4	bps3200
5	bps6400

.1.3.6.1.4.1.164.3.6.2.2.1.6

mdlKmxV54Config

Relevant only for KLS.1/New card.

Enumerationr/w

.1.3.6.1.4.1.164.3.6.2.2.1.7

mdlKmxTiming

Applicable only for KHSU.1, KHSU.2, KVF.4/S0, KVC.3/S0 cards.
lt - local timing
nt - network timing
te - terminal equipment

Enumeration

.1.3.6.1.4.1.164.3.6.2.2.1.8

mdlKmxIsdnDisconnectCause

This attribute indicates the cause of the ISDN Disconnection for
the card installed in the specific slot position. The value can be
0..255. The numeric values have a well known meaning for ISDN experts.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.3.6.2.2.1.9

mdlKmxIsdnCallStatus

This attribute indicates the current ISDN Call Status for
the card installed in the specific slot position.

Enumeration

.1.3.6.1.4.1.164.3.6.2.2.1.10

mdlKmxIsdnLayer1State

This attribute indicates the ISDN Layer 1 State for
the card installed in the specific slot position.

Enumeration

.1.3.6.1.4.1.164.3.6.2.2.1.11

mdlKmxIsdnLayer2State

This attribute indicates the ISDN Layer 2 State for
the card installed in the specific slot position.

Enumeration

.1.3.6.1.4.1.164.3.6.2.2.1.12

mdlKvf5PbxTable

table

.1.3.6.1.4.1.164.3.6.2.3 · 1 row entry · 14 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlKvf5PbxTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlKvf5PbxTable'

Parameters specific to KVF.5, KVF.6 and KVF.8 PBX cards.

mdlKvf5PbxEntry row .1.3.6.1.4.1.164.3.6.2.3.1

An entry in table.

Indexes

prtMlCnfgIdx prtMlIdx

Column Syntax OID

mdlKvf5PbxConfigIdx

This object indicates the Configuration number (1..255)
referred.
Value of 255 specifies the TmpCnfg (Scratch).
Write operation for the table entries is allowed only to
Config=255.

Integer32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.6.2.3.1.1

mdlKvf5PbxSlotIdx

This object indicates a unique number of the slot position
in which the module is inserted.

Enumeration

.1.3.6.1.4.1.164.3.6.2.3.1.2

mdlKvf5PbxSig

Signaling type.
When 'mdlKvf5PbxSig' is valid, 'mdlKvf5PbxSigTxPbx' and 'mdlKvf5PbxSigRxPbx'
are not valid.
mdlKvf5PbxSig - is supported by KVF.5 OLD SW ver and KVF.6 card.
mdlKvf5PbxSigTxPbx and mdlKvf5PbxSigRxPbx -…

Enumerationr/w

Enumerated Values:

103	kmxMlA
104	kmxMlB

.1.3.6.1.4.1.164.3.6.2.3.1.3

mdlKvf5PbxSigMode

Signaling Mode.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	dte
3	dce
4	eDce
5	int
6	lbt
7	adaptive

.1.3.6.1.4.1.164.3.6.2.3.1.4

mdlKvf5PbxTsAssign

Ts Assignment group. Each KVF.5 card of the Mux should have
a different value.
For KVF.5/E1 values: 2,3,4,8,9,10,11,12 are applicable.
For KVF.5/T1 values: 2,3,4,5,6,7 are applicable.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	bits8
3	bits256

.1.3.6.1.4.1.164.3.6.2.3.1.5

mdlKvf5PbxCcsTs

CCS TS of the KVF.5/T1/E1 and KVF.6/T1/E1 card.
It is applicable for Kmux KVF.5 Framer cards and KVF.6 cards
when mdlKvf5PbxSig=ccs.
Valid values:
1..24 - CCS TS of T1
1..31 - CCS TS of E1
255 - notApplicable (for age…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	internal
3	external

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.2.3.1.6

mdlKvf5PbxOos

Enumerationr/w

Enumerated Values:

2	bps9600
3	bps14400
4	bps19200
5	bps28800
6	bps32000
7	bps48000
8	bps56000
9	bps64000
10	bps128000
11	bps192000
12	bps256000
13	bps384000
14	bps512000
15	bps768000
16	bps1024000
17	bps1536000

.1.3.6.1.4.1.164.3.6.2.3.1.7

mdlKvf5PbxSigTxPbx

TxPbx signaling means transmit signaling from KM to PBX (KM-->PBX)
When 'mdlKvf5PbxSigTxPbx' is valid, 'mdlKvf5PbxSig' field is not valid.
mdlKvf5PbxSig - is supported by KVF.5 OLD SW ver.
mdlKvf5PbxSigTxPbx and mdlKv…

Enumerationr/w

Constraints:
range: 0-31

.1.3.6.1.4.1.164.3.6.2.3.1.8

mdlKvf5PbxSigRxPbx

RxPbx signaling means receive signaling from PBX to KM (PBX-->KM-->KM)
When 'mdlKvf5PbxSigRxPbx' is valid, 'mdlKvf5PbxSig' field is not valid.
mdlKvf5PbxSig - is supported by KVF.5 OLD SW ver.
mdlKvf5PbxSigTxPbx and md…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.3.6.2.3.1.9

mdlKvf5PbxDefABCD

This object determines what KM will send for the ABCD Bits that
are not 'filled' by the dynamic signaling. This field is applicable
only for signaling transmit to PBX ('mdlKvf5PbxSigTxPbx').
For KVF.5 cards: valid ran…

OctetStringr/w

Enumerated Values:

1	notApplicable
2	initiate
3	listen

.1.3.6.1.4.1.164.3.6.2.3.1.10

mdlKvf5PbxFramerSlot

This object indicates the Framer's slot number this card belongs to.
Several cards having the same mdlKvf5PbxFramerSlot value, work together
as a group.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disabled
3	enabled

.1.3.6.1.4.1.164.3.6.2.3.1.11

mdlKvf5PbxCcsRate

Determines the Ccs speed - for KVF.6 and KVF.5 cards.

Enumerationr/w

.1.3.6.1.4.1.164.3.6.2.3.1.12

mdlKvf5PbxTxAbcdBit

This object is applicable only for KVF.6 and KVF.8 cards, when mdlKvf5PbxSig=cas(6).
It represents 4 parameters, by 2 Octets :
D Bit Code-MSB nibble,
C Bit Code- nibble,
B Bit Code- nibble,
A Bit Code-LSB nibble.
…

OctetStringr/w

.1.3.6.1.4.1.164.3.6.2.3.1.13

mdlKvf5PbxHdlcCrc

Determines the CRC type of HDLC protocol, that CCS signaling
is working with. Applicable for KVF.6 cards when Signaling
is CCS (only).

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.6.2.3.1.14

mdlDisconnectSupervisionTable

table

.1.3.6.1.4.1.164.3.6.2.4 · 1 row entry · 17 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mdlDisconnectSupervisionTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mdlDisconnectSupervisionTable'

Disconnect Supervision table.

mdlDisconnectSupervisionEntry row .1.3.6.1.4.1.164.3.6.2.4.1

An entry in the table.

Indexes

No indexes recorded

Column Syntax OID

mdlDsConfigIdx

This object indicates the Configuration number (1..255)
referred.
Value of 255 specifies the TmpCnfg (Scratch).
Write operation for the table entries is allowed only to
Config=255.

Integer32

Enumerated Values:

2	leased
3	switched

.1.3.6.1.4.1.164.3.6.2.4.1.1

mdlDsSlotIdx

This object indicates a unique number of the slot position
in which the module is inserted.

Enumeration

Enumerated Values:

2	european
3	israeli
4	ess5Multipoint
5	ess5Ptp
6	dms100
7	ntt
8	nationalIsdn1

.1.3.6.1.4.1.164.3.6.2.4.1.2

mdlDs

This object defines which terms will cause disconnection of call.
disable = the Disconnect Supervision feature is disabled. In this case,
all other objects of this table are irrelevant.

Remote Sanity -
I…

Enumerationr/w

Constraints:
range: 0-25

.1.3.6.1.4.1.164.3.6.2.4.1.3

mdlDsUserLoc

User located in local or remote station.
Local station will disconnect the call actually if needed.
Applicable only if Disconnect Supervision (mdlDs) is different from disable.
Should be a Sanity check between the mdlDs…

Enumerationr/w

Constraints:
range: 0-25

.1.3.6.1.4.1.164.3.6.2.4.1.4

mdlDsMode

This object defines the action, which will be done after remote disconnect occurred.
This object is relevant only when mdlDsUserLoc = local(3).
Applicable only if Disconnect Supervision (mdlDs) is different from disable…

Enumerationr/w

Constraints:
range: 0-25

.1.3.6.1.4.1.164.3.6.2.4.1.5

mdlDsSilence

This object defines the silence period needed for an indication (seconds).
Applicable only if Disconnect Supervision (mdlDs) is different from disable
AND includes 'Silence', i.e. is one of the following:
remote…

SNMPv2-SMIInteger32r/w

Constraints:
range: 0-25

.1.3.6.1.4.1.164.3.6.2.4.1.6

mdlDsClrFwSig

This object defines the Clear FWD Signal (A,B,C,D bits) for KVF.6 cards.
This object is an indication of Near PBX to the Far PBX,
that it wants to disconnect the call.
Applicable only if Disconnect Supervision (mdlDs) …

OctetStringr/w

Enumerated Values:

2	none
3	all
4	local

.1.3.6.1.4.1.164.3.6.2.4.1.7

mdlDsAnswerSig

This object defines the Clear FWD Signal (A,B,C,D bits) for KVF.6 cards.
This object is an indication of Near PBX to the Far PBX,
taht a call is present now on the line.
Applicable only if Disconnect Supervision (md…

OctetStringr/w

.1.3.6.1.4.1.164.3.6.2.4.1.8

mdlDsClrBwSig

This object defines the Clear FWD Signal (A,B,C,D bits) for KVF.6 cards.
This object is an indication of Far PBX to the Near PBX,
that the call was disconnected (on the Far side).
Applicable only if Disconnect Super…

OctetStringr/w

.1.3.6.1.4.1.164.3.6.2.4.1.9

mdlDsFbtLowFreq

First frequency in Fast Busy Tone (Fbt) combination (Hz).
Valid values: 0..4000,4095. 4095 = notApplicable.
Available only if Disconnect Supervision (mdlDs) is different from disable
AND includes 'Tones' (Fast Busy)…

SNMPv2-SMIInteger32r/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.6.2.4.1.10

mdlDsFbtHighFreq

Second frequency in Fast Busy Tone (Fbt) combination (Hz).
Valid values: 0..4000,4095. 4095 = notApplicable.
Available only if Disconnect Supervision (mdlDs) is different from disable
AND includes 'Tones' (Fast Busy…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.2.4.1.11

mdlDsFbtTimeOn1

This object defines the Time On 1 cadence (in msec).
Valid values: 0,10,20..(every 10 msec)..10000,10230.
0 = disable, 10230 = notApplicable.
Available only if Disconnect Supervision (mdlDs) is different from disable
…

SNMPv2-SMIInteger32r/w

Enumerated Values:

106	kmxOpt
107	kmxIO1
108	kmxIO2
109	kmxIO3
110	kmxIO4
111	kmxIO5
112	kmxIO6
113	kmxIO7
114	kmxIO8
115	kmxIO9
116	kmxIO10
117	kmxIO11
118	kmxIO12

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.2.4.1.12

mdlDsFbtTimeOff1

This object defines the Time Off 1 cadence (in msec).
Valid values: 0,10,20..(every 10 msec)..10000,10230.
0 = disable, 10230 = notApplicable.
Available only if Disconnect Supervision (mdlDs) is different from d…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	async
3	sync

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.2.4.1.13

mdlDsFbtTimeOn2

This object defines the Time On 2 cadence (in msec).
Valid values: 0,10,20..(every 10 msec)..10000,10230.
0 = disable, 10230 = notApplicable.
Available only if Disconnect Supervision (mdlDs) is different from di…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	bit6
3	bit7
4	bit8
5	bit9

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.2.4.1.14

mdlDsFbtTimeOff2

This object defines the Time Off 2 cadence (in msec).
Valid values: 0,10,20..(every 10 msec)..10000,10230.
0 = disable, 10230 = notApplicable.
Available only if Disconnect Supervision (mdlDs) is different from d…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	dce
3	dte1
4	dte2

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.2.4.1.15

mdlDsFbtLowFreqLevel

First frequency level for Fast Busy Tone (Fbt) in dBm units.
Valid values: -32..31.
Available only if Disconnect Supervision (mdlDs) is different from disable
AND includes 'Tones' (Fast Busy), i.e. is one of the fol…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	local
3	dtrAndRts
4	rts

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.2.4.1.16

mdlDsFbtHighFreqLevel

Second frequency level for Fast Busy Tone (Fbt) in dBm units.
Valid values: -32..31.
Available only if Disconnect Supervision (mdlDs) is different from disable
AND includes 'Tones' (Fast Busy), i.e. is one of the fo…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	equalRts
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.2.4.1.17

prtMlFrameStatsTable

table

.1.3.6.1.4.1.164.3.6.3.1.1 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtMlFrameStatsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtMlFrameStatsTable'

Frame diagnostics for the main links.

prtMlFrameStatsEntry row .1.3.6.1.4.1.164.3.6.3.1.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtMlFrameIdx

The prtGenPrtIdx index of this link.
Slot*100+1.

SNMPv2-SMIInteger32

Enumerated Values:

1	notConnected
2	bps300
3	bps600
4	bps1200
5	bps2400
6	bps4800
7	bps7200
8	bps8000
9	bps9600
10	bps12000
11	bps14400
12	bps16000
13	bps16800
14	bps19200
15	bps21600
16	bps24000
17	bps26400
18	bps28800
19	bps31200
20	bps32000
21	bps33600
22	bps36000
23	bps38400
24	bps40800
25	bps43200
26	bps45600
27	bps48000
28	bps50400
29	bps52800
30	bps55200
31	bps56000
32	bps57600
33	bps60000
34	bps62400
35	bps64000
36	bps64800
37	bps67200
38	bps69600
39	bps72000
40	bps74400
41	bps76800
42	bps79200
43	bps81600
44	bps84000
45	bps86400
46	bps88800
47	bps91200
48	bps93600
49	bps96000
50	bps98400
51	bps100800
52	bps103200
53	bps105600
54	bps108000
55	bps110400
56	bps112800
57	bps115200
58	bps117600
59	bps120000
60	bps122400
61	bps124800
62	bps127200
63	bps128000
64	bps129600
65	bps134400
66	bps139200
67	bps144000
68	bps148800
69	bps153600
70	bps158400
71	bps163200
72	bps168000
73	bps172800
74	bps177600
75	bps182400
76	bps187200
77	bps192000
78	bps196800
79	bps201600
80	bps206400
81	bps211200
82	bps216000
83	bps220800
84	bps225600
85	bps230400
86	bps235200
87	bps240000
88	bps244800
89	bps249600
90	bps254400
91	bps256000
92	bps259200
93	bps264000
94	bps268800
95	bps273600
96	bps278400
97	bps283200
98	bps288000
99	bps292800
100	bps297600
101	bps302400
102	bps307200
103	bps316800
104	bps326400
105	bps336000
106	bps345600
107	bps355200
108	bps364800
109	bps374400
110	bps384000
111	bps393600
112	bps403200
113	bps412800
114	bps422400
115	bps432000
116	bps441600
117	bps451200
118	bps460800
119	bps470400
120	bps480000
121	bps489600
122	bps499200
123	bps508800
124	bps518400
125	bps528000
126	bps537600
127	bps547200
128	bps556800
129	bps566400
130	bps576000
131	bps585600
132	bps595200
133	bps604800
134	bps614400

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.3.1.1.1.1

prtMlFrameSlt

This attribute indicates a unique number to identify the slot
where the ML card is inserted.

Enumeration

Enumerated Values:

1	notApplicable
2	regular
3	type1

.1.3.6.1.4.1.164.3.6.3.1.1.1.2

prtMlBitWeight

This attribute indicates the Bit Weight [bps/bit] used for
the selected prtMlFrameSlt. The Bit Weight is according to
the ML Speed.

Enumeration

.1.3.6.1.4.1.164.3.6.3.1.1.1.3

prtMlDataUsage

Data usage in [bits].
In order to convert it to 'bps' units, the 'bits' should be multiplied
by prtMlBitWeight value.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.3.1.1.1.4

prtMlControlSig

Control Signals usage of the ML in [bits].
In order to convert it to 'bps' units, the 'bits' should be multiplied
by prtMlBitWeight value.

SNMPv2-SMIInteger32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.6.3.1.1.1.5

prtMlDownload

Download bandwidth usage of the ML in [bits].
In order to convert it to 'bps' units, the 'bits' should be multiplied
by prtMlBitWeight value.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.3.1.1.1.6

prtMlSync

Sync bandwidth usage of the ML in [bits].
In order to convert it to 'bps' units, the 'bits' should be multiplied
by prtMlBitWeight value.

SNMPv2-SMIInteger32

Enumerated Values:

107	kmxIO1
108	kmxIO2
109	kmxIO3
110	kmxIO4
111	kmxIO5
112	kmxIO6
113	kmxIO7
114	kmxIO8
115	kmxIO9
116	kmxIO10
117	kmxIO11
118	kmxIO12

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.3.1.1.1.7

prtMlTotalUsage

Total bandwidth usage of the ML in [bits].
In order to convert it to 'bps' units, the 'bits' should be multiplied
by prtMlBitWeight value.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	main
3	remote

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.3.1.1.1.8

prtMlTotalFree

Free bandwidth of the ML in [bits].
In order to convert it to 'bps' units, the 'bits' should be multiplied
by prtMlBitWeight value.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	r4M
3	r16M

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.3.1.1.1.9

prtMlTable

table

.1.3.6.1.4.1.164.3.6.3.1.2 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtMlTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtMlTable'

Parameters for the main links. 
KML.1 - KML.6, KML.7(T1), KML.8(E1), KML.10(ISDN) and 
KML.F(KML.11 Fiber-optic).

prtMlEntry row .1.3.6.1.4.1.164.3.6.3.1.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtMlCnfgIdx

This attribute indicates the Idx of the Config being accessed.
Idx of 255 relates to the Temporary (Scratch) Config.
Write operation for the table entries is allowed only to
Config=255.

Integer32

.1.3.6.1.4.1.164.3.6.3.1.2.1.1

prtMlIdx

The prtGenPrtIdx index of this link.
Slot*100+1 .

SNMPv2-SMIInteger32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.3.6.3.1.2.1.2

prtMlSlt

This attribute indicates a unique number to identify the slot where
the ML card is inserted in.

Enumeration

.1.3.6.1.4.1.164.3.6.3.1.2.1.3

prtMlTiming

The clock source for this link.
For KML.1-KML.4, valid values: dte, eDce, or dce.
For KML.5-KML.8, valid values: int or lbt.
notApplicable - for KML.10 and KML.F.

Enumerationr/w

Enumerated Values:

107	kmxIO1
108	kmxIO2
109	kmxIO3
110	kmxIO4
111	kmxIO5
112	kmxIO6
113	kmxIO7
114	kmxIO8
115	kmxIO9
116	kmxIO10
117	kmxIO11
118	kmxIO12

.1.3.6.1.4.1.164.3.6.3.1.2.1.4

prtMlBufferSize

The buffer size in bits for absorbing timing jitters.

Enumerationr/w

.1.3.6.1.4.1.164.3.6.3.1.2.1.5

prtMlDsrCts

Determines the DSR and CTS signal handling.
notApplicable - for KML.4-KML.6.

Enumerationr/w

.1.3.6.1.4.1.164.3.6.3.1.2.1.6

prtMlSpeed

Determines the Main Link port speed.
KML.1, KML.3, KML.4 support (Kbps): 9.6, 14.4, 19.2, 28.8, 32, 48, 56,
64, 128, 192, 256, 384, 512, 768, 1024, 1536.
KML.2 supports (Kbps): 9.6…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	w2wire
3	w4wire

.1.3.6.1.4.1.164.3.6.3.1.2.1.7

prtMlStartTS

0=notApplicable - for all cards except KML.7, KML.8
For KML.7 - valid values: 1..24
For KML.8 - valid values: 1..31.

Integer32r/w

Enumerated Values:

1	notApplicable
2	manual
3	sec30
4	sec60
5	sec90

.1.3.6.1.4.1.164.3.6.3.1.2.1.8

prtMlBypassTs16

notApplicable - for all cards except KML.8.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	off
3	on

.1.3.6.1.4.1.164.3.6.3.1.2.1.9

prtMlCallMode

This object will be used when using an external modem linked to the
KML.1-KML.4 or KML.10 cards.
Initiate - KML card can initiate calls to the modem
Listen - KML card listens only ; cannot initiate a call.

Enumerationr/w

Enumerated Values:

1	notConnected
2	bps4800
3	bps6400
4	bps7200
5	bps8000
6	bps9600
7	bps12800
8	bps16000
9	bps24000
10	bps32000
11	bps64000
12	bps11200

.1.3.6.1.4.1.164.3.6.3.1.2.1.10

prtMlBondingEnable

Disable/Enable applying the Bonding process, for KML.10 cards.
notApplicable - for all cards except KML.10.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	r16Khz
3	r12Khz

.1.3.6.1.4.1.164.3.6.3.1.2.1.11

prtMlIsdnTable

table

.1.3.6.1.4.1.164.3.6.3.1.3 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtMlIsdnTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtMlIsdnTable'

Parameters for ISDN main links: KML.10.

prtMlIsdnEntry row .1.3.6.1.4.1.164.3.6.3.1.3.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtMlIsdnCnfgIdx

This attribute indicates the Idx of the Config being accessed.
Idx of 255 relates to the Temporary (Scratch) Config.
Write operation for the table entries is allowed only to
Config=255.

Integer32

Constraints:
range: 2-2

.1.3.6.1.4.1.164.3.6.3.1.3.1.1

prtMlIsdnIdx

The prtGenPrtIdx index of this link.
Slot*100+1 .

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	s1s2s3s4
3	s5s6s7s8
4	s9s10s11s12
5	s13s14s15s16
6	s17s18s19s20
7	s21s22s23s24
8	s25s26s27s28
9	s29s30s31

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.3.1.3.1.2

prtMlIsdnSlt

This attribute indicates a unique number to identify the slot where
the ML card is inserted in.

Enumeration

.1.3.6.1.4.1.164.3.6.3.1.3.1.3

prtMlIsdnMode

ISDN Mode.
switched - when ML Mode is Switched Backup.
leased - in all other cases.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	sec0
3	sec10

.1.3.6.1.4.1.164.3.6.3.1.3.1.4

prtMlIsdnStandard

The ISDN standard.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	loopStart
3	groundStart
4	winkStart

.1.3.6.1.4.1.164.3.6.3.1.3.1.5

prtMlIsdnLocSubNum

Local sub-number. 4 chars (digits 0..9).

OctetStringr/w

Enumerated Values:

1	notApplicable
2	em1
3	em2
4	em3
5	ssdc5

.1.3.6.1.4.1.164.3.6.3.1.3.1.6

prtMlIsdnLocNum

Local number. 20 chars (digits: 0..9).

OctetStringr/w

Enumerated Values:

1	notApplicable
2	f16dot7Hz
3	f20Hz
4	f25Hz
5	f50Hz

.1.3.6.1.4.1.164.3.6.3.1.3.1.7

prtMlIsdnOutSubNum

Out sub-number. 4 chars (digits 0..9).

OctetStringr/w

Constraints:
range: 0-2

.1.3.6.1.4.1.164.3.6.3.1.3.1.8

prtMlIsdnBackupCallNum

Backup call number. 20 chars (digits: 0..9).

OctetStringr/w

.1.3.6.1.4.1.164.3.6.3.1.3.1.9

prtMlIsdnInNumMode

In number mode.

Enumerationr/w

.1.3.6.1.4.1.164.3.6.3.1.3.1.10

prtHsLsTable

table

.1.3.6.1.4.1.164.3.6.3.2.1 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtHsLsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtHsLsTable'

Parameters for the High and Low speed channels. 
Cards: KLS.1,KLS.2, KHS.1, KHS.2, KDI/CH, KHSU.1, KHSU.2, KHS.703.

prtHsLsEntry row .1.3.6.1.4.1.164.3.6.3.2.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtHsLsCnfgIdx

This attribute indicates the Idx of the Config being accessed.
Idx of 255 relates to the Temporary (Scratch) Config.
Write operation for the table entries is allowed only to
Config=255.

Integer32

.1.3.6.1.4.1.164.3.6.3.2.1.1.1

prtHsLsIdx

The prtGenPrtIdx index of this channel.
In KHSU.1 and KHSU.2 there are three ISDN sub-channels on
each port (2B+D).The sub-channels are numbered:
Slot*100+11 ; Slot*100+12 ; Slot*100+13 (First Port),
Slot*100+14 ; S…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.3.2.1.1.2

prtHsLsSlt

This attribute indicates a unique number to identify the slot where
the card is inserted in.
In the 2104 Unit the entries kmxIO5(111)..kmxIO12(118) are not valid.
The entry kmxOpt(106) is valid only for KDI/CH card.

Enumeration

Constraints:
range: 1-100

.1.3.6.1.4.1.164.3.6.3.2.1.1.3

prtHsLsCommProtocol

The communication protocol.

Enumerationr/w

.1.3.6.1.4.1.164.3.6.3.2.1.1.4

prtHsLsAsyncDataLen

Async Data Length in Bits.
notApplicable - when prtHsLsCommProtocol=sync or
notApplicable.

Enumerationr/w

.1.3.6.1.4.1.164.3.6.3.2.1.1.5

prtHsLsTiming

The variable is RW only if the communications protocol is
sync.
When the comm protocol is async, the variable is RO and its
value is DCE.

Enumerationr/w

.1.3.6.1.4.1.164.3.6.3.2.1.1.6

prtHsLsCtrlSignal

Control signals.

Enumerationr/w

Constraints:
range: 1-40

.1.3.6.1.4.1.164.3.6.3.2.1.1.7

prtHsLsCts

CTS Signal.

Enumerationr/w

Enumerated Values:

1	off
2	on

.1.3.6.1.4.1.164.3.6.3.2.1.1.8

prtHsLsRtsCtsDelay

RTS-CTS delay in ms.
notApplicable - when prtHsLsCts=on.

Enumerationr/w

Enumerated Values:

1	off
2	on

.1.3.6.1.4.1.164.3.6.3.2.1.1.9

prtHsLsDsrMode

DSR Mode.

Enumerationr/w

Constraints:
range: 0-6

.1.3.6.1.4.1.164.3.6.3.2.1.1.10

prtHsLsSpeed

KLS.1 supports (Kbps): 0.3, 0.6, 1.2, 2.4, 4.8, 9.6, 19.2, 38.4.
KLS.1/New, KDI/CH support (Kbps):
Group 1: 0.3, 0.6, 1.2, 2.4, 4.8, 9.6,
19.2, 38.4
…

Enumerationr/w

Constraints:
range: 0-6

.1.3.6.1.4.1.164.3.6.3.2.1.1.11

prtHsLsUType

U Interface Type. Applicable for KHSU.1/2 cards.
The value will be the same for B1 and B2 pair; B3 and B4.

Enumerationr/w

.1.3.6.1.4.1.164.3.6.3.2.1.1.12

prtTreMbeTable

table

.1.3.6.1.4.1.164.3.6.3.3.2 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtTreMbeTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtTreMbeTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry. Parameters for the channels of the
TRE and MBE cards: KTRE, KMBE, KMBE/NEW.

prtTreMbeEntry row .1.3.6.1.4.1.164.3.6.3.3.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtTreMbeCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

Constraints:
range: 0-6

.1.3.6.1.4.1.164.3.6.3.3.2.1.1

prtTreMbeIdx

A unique port identifier within the card.
Slot*100+11 .

SNMPv2-SMIInteger32

Constraints:
range: 0-6

.1.3.6.1.4.1.164.3.6.3.3.2.1.2

prtTreMbeSlt

This attribute indicates a unique number to identify the slot where
the card is inserted in.
In the 2104 Unit the entries kmxIO5(111)..kmxIO12(118) are not valid.

Enumeration

Enumerated Values:

1	on
2	off

.1.3.6.1.4.1.164.3.6.3.3.2.1.3

prtTreMbeLan

This attribute indicates whether the TRE/MBE port is operated
as main or remote bridge.
Default=remote.

Enumerationr/w

Enumerated Values:

1	none
2	local
3	remote
4	bonding

.1.3.6.1.4.1.164.3.6.3.3.2.1.4

prtTreMbeLanRate

This attribute indicates the Rate of the TRE port
in Mbit/sec. Default-r4M.

Enumerationr/w

Enumerated Values:

1	none
2	local
3	remote
4	bonding
5	all

.1.3.6.1.4.1.164.3.6.3.3.2.1.5

prtTreMbeLinkSpeed

The Link Speed.

Enumerationr/w

.1.3.6.1.4.1.164.3.6.3.3.2.1.6

prtVoiceFaxTable

table

.1.3.6.1.4.1.164.3.6.3.4.1 · 1 row entry · 20 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtVoiceFaxTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtVoiceFaxTable'

The write operation into the Table Objects is valid only
to the TmpCnfg entry. Parameters for the channels of the
Voice and Fax channels. 
Cards: KVC.1/E&M,  KVC.1/FXO,  KVC.1/FXS,
       KVC.1M/E&M, KVC.1M/FXO, KVC.1M/FXS, KVC.1M/FXSW, 
       KVC.2/E&M,  KVC.2/FXO,  KVC.2/FXS, 
       KVC.2/1/E&M,KVC.2/1/FXO,KVC.2/1/FXS, 
       KVC.3/E&M,  KVC.3/FXO,  KVC.3/FXS, KVC.3/S0
       KVF.1/E&M,  KVF.1/FXO,  KVF.1/FXS, 
       KVF.3/E&M,  KVF.3/FXO,  KVF.3/FXS, 
       KVF.4/E&M,  KVF.4/FXO,  KVF.4/FXS, KVF.4/FXSW, KVF.4/S0,
       KVF.4/FXO3, KVF.4/FXS3, KVF.4/NS0     
       KVF.5 family, KVF.6 family, KVF.8 family.

prtVoiceFaxEntry row .1.3.6.1.4.1.164.3.6.3.4.1.1

An entry in table.

Indexes

chIndex

Column Syntax OID

prtVoiceFaxCnfgIdx

This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg.

Integer32

Constraints:
range: 1-6

.1.3.6.1.4.1.164.3.6.3.4.1.1.1

prtVoiceFaxIdx

A unique identifier of the port, within the card.
Slot*100+Ch
external ports: Ch=1..10
internal ports (sub-channels): Ch=11..20.

SNMPv2-SMIInteger32

Enumerated Values:

1	on
2	off

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.3.4.1.1.2

prtVoiceFaxSlt

This attribute indicates a unique number to identify the slot where
the card is inserted in.
In the 2104 Unit the entries kmxIO5(111)..kmxIO12(118) are not valid.

Enumeration

Enumerated Values:

1	on
2	off

.1.3.6.1.4.1.164.3.6.3.4.1.1.3

prtVoiceFaxTransGain

Transmit gain in dBm. A value of 255 is for notApplicable.
The value will be: real value+50dBm (in order to avoid
negative values).

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.3.4.1.1.4

prtVoiceFaxReceiveGain

Receive gain in dBm. A value of 255 is for notApplicable.
The value will be: real value+50dBm (in order to avoid
negative values).

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.3.4.1.1.5

prtVoiceFaxWire

Applicable only for E&M cards.

Enumerationr/w

Enumerated Values:

1	up
2	down
3	engaged
4	notDedicated

.1.3.6.1.4.1.164.3.6.3.4.1.1.6

prtVoiceFaxTimeOut

Fax timeout in seconds.

Enumerationr/w

.1.3.6.1.4.1.164.3.6.3.4.1.1.7

prtVoiceFaxEchoCanceler

Echo canceler activation.

Enumerationr/w

.1.3.6.1.4.1.164.3.6.3.4.1.1.8

prtVoiceFaxSpeed

The channel speed.
For KVF.6 and KVF.8 cards, each value will represent [4 x value], since each
channel (Internal or External) is comprised of 4 sub-channels having the selected value.

Enumerationr/w

Enumerated Values:

1	tx
2	rx
3	compress
4	priority
5	loadSharing
6	facs
7	codConnect
8	codDisconnect

.1.3.6.1.4.1.164.3.6.3.4.1.1.9

prtVoiceFaxMeterRate

This entry is valid to KVF.4/FXO3 and KVF.4/FXS3.
Meter Rate means rate of Call Meter in Public Phones, in KHz units.
Must be equal for both channels.

Enumerationr/w

.1.3.6.1.4.1.164.3.6.3.4.1.1.10

prtVoiceFaxCodingLaw

Coding Law. This entry is valid for KVF.4/NS0 external channel and
KVF.6 internal channels.

Enumerationr/w

.1.3.6.1.4.1.164.3.6.3.4.1.1.11

prtVoiceFaxOperMode

Operation Mode. This parameter is valid for KVF.6 and KVF.8 family.

Enumerationr/w

Enumerated Values:

1	unassigned-cond
2	broadcast-msge
3	multicast-msge
4	all-msge
5	none

.1.3.6.1.4.1.164.3.6.3.4.1.1.12

prtVoiceFaxSigInOutband

This object is applicable for KVF.4/FXO3, KVF.4/FXS3, KVF.8 family cards.

For KVF.4/FXO3, KVF.4/FXS3:
Octet 1 for Receive parameters.
Octet 2 for Transmit parameters.
It represents 4 parameters, in each …

OctetStringr/w

.1.3.6.1.4.1.164.3.6.3.4.1.1.13

prtVoiceFaxTsGroup

Ts Assignment group. Each KVF.6 internal channel should have
a different value.
's21s22s23s24' = TSs: 21, 22, 23, 24
For KVF.6/E1/16, KVF.6/E1/31 values: 2..9 are applicable.
For KVF.6/T1/12, KVF.6/T1/24 values…

Enumerationr/w

.1.3.6.1.4.1.164.3.6.3.4.1.1.14

prtVoiceFaxRxFaxGain

FAX Receive gain in dBm.
The value will be: (real value*10)+500dBm (in order to avoid
negative and fractional values).

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	mac
2	llc
3	net

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.6.3.4.1.1.15

prtVoiceFaxSigHold

Signal Hold in [sec]. Applicable for all KVF.4 cards except S0/NS0.
When a ML fails, instead of interrupting immediately a
conversation and connecting it again when ML operation is resumed,
user can select to Hold the…

Enumerationr/w

.1.3.6.1.4.1.164.3.6.3.4.1.1.16

prtVoiceFaxIfSignaling

Applicable only for KVF.8/FXO, KVF.8/FXS cards.
Interface Analog Signaling.

Enumerationr/w

Enumerated Values:

1	false
2	true

.1.3.6.1.4.1.164.3.6.3.4.1.1.17

prtVoiceFaxEMTypes

Applicable only for KVF.8/E&M card.

Enumerationr/w

.1.3.6.1.4.1.164.3.6.3.4.1.1.18

prtVoiceFaxRingFrequency

Applicable only for KVF.8/E&M card.
The Ringing Frequency units will be in Hz.

Enumerationr/w

.1.3.6.1.4.1.164.3.6.3.4.1.1.19

prtVoiceFaxSignalingStatus

For KM-2100 this parameter should be Read Only.
This object is applicable for KVF.6 and KVF.5 family cards.
It shows the status (0 or 1) of each Signaling Bit (A, B, C, D),
for each TS of a TS Group (according …

OctetStringr/w

Enumerated Values:

1	mac
2	llc
3	net

.1.3.6.1.4.1.164.3.6.3.4.1.1.20

sysGenAlarmBuffTable

table

.1.3.6.1.4.1.164.3.7.1.1.2 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sysGenAlarmBuffTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sysGenAlarmBuffTable'

The alarm buffer of the imx.

sysGenAlarmBuffEntry row .1.3.6.1.4.1.164.3.7.1.1.2.1

An entry in table sysGenAlarmBuffTable.

Indexes

No indexes recorded

Column	Syntax	OID
sysGenAlarmBuffIndex The index of the alarm buffer Table.	Integer32	`.1.3.6.1.4.1.164.3.7.1.1.2.1.1`
sysGenAlarmDescr The description of the alarm. Up to 80 chars.	SNMPv2-TCDisplayString Type Constraints: `range: 0..255` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.164.3.7.1.1.2.1.2`

sysGenLogTable

table

.1.3.6.1.4.1.164.3.7.1.1.4 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sysGenLogTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sysGenLogTable'

The call log buffer of the imx.

sysGenLogEntry row .1.3.6.1.4.1.164.3.7.1.1.4.1

An entry in table sysGenLogTable.

Indexes

No indexes recorded

Column Syntax OID

sysGenLogIndex

The index of the log Table.

Integer32

Enumerated Values:

1	false
2	true

.1.3.6.1.4.1.164.3.7.1.1.4.1.1

sysGenLogDescr

The description of the entry in the log buffer. Up to 80 chars.

SNMPv2-TCDisplayString

Enumerated Values:

1	block
2	forward
3	route
4	forward-route
5	high-priority
6	noOp
7	delete

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.3.7.1.1.4.1.2

sysCallProfileTable

table

.1.3.6.1.4.1.164.3.7.1.2.1.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sysCallProfileTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sysCallProfileTable'

A table containing call profile parameters. There are 40 call
profiles.

sysCallProfileEntry row .1.3.6.1.4.1.164.3.7.1.2.1.1.1

An entry in table sysCallProfileTable.

Indexes

radBridgeCODIfIndex

Column Syntax OID

sysCallProfileIndex

A running index for the table.

Integer32

.1.3.6.1.4.1.164.3.7.1.2.1.1.1.1

sysCallProfileConnectCmd

On(2) - Connect the call profile. The agent will automatically
reset the variable to off(1) .

Enumerationr/w

Enumerated Values:

1	connect
2	disconnect

.1.3.6.1.4.1.164.3.7.1.2.1.1.1.2

sysCallProfileDisconnectCmd

On(2) - Disconnect the call profile. The agent will automatically
reset the variable to off(1).

Enumerationr/w

Enumerated Values:

1	answer
2	originate
3	disable
4	answerAndOriginate

.1.3.6.1.4.1.164.3.7.1.2.1.1.1.3

sysCallProfileIncrBwCmd

Increment bandwidth of a call.
The number of channels to increment 1..6. The agent will automatically
reset the variable to 0.

Integer32r/w

.1.3.6.1.4.1.164.3.7.1.2.1.1.1.4

sysCallProfileDecrBwCmd

Decrement bandwidth of a call.
The number of channels to decrement 1..6. The agent will automatically
reset the variable to 0.

Integer32r/w

.1.3.6.1.4.1.164.3.7.1.2.1.1.1.5

prtCnfgTable

table

.1.3.6.1.4.1.164.3.7.2.1.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtCnfgTable'

A table containing configuration parameters for the user ports.

prtCnfgEntry row .1.3.6.1.4.1.164.3.7.2.1.1.1

An entry in table prtCnfgTable.

Indexes

No indexes recorded

Column Syntax OID

prtIndex

The user port index.

Integer32

.1.3.6.1.4.1.164.3.7.2.1.1.1.1

prtCnfgDecrBwChNum

Decrement the port bandwidth by the specified number of channels.
The agent resets the variable to 0.

Integer32r/w

.1.3.6.1.4.1.164.3.7.2.1.1.1.2

prtCnfgIncrBwChNum

Increment the port bandwidth by the specified number of channels.
The agent resets the variable to 0.

Integer32r/w

.1.3.6.1.4.1.164.3.7.2.1.1.1.3

prtCnfgDisconnect

Disconnect the port (on(1)). The agent resets the variable to off(2).

Enumerationr/w

.1.3.6.1.4.1.164.3.7.2.1.1.1.4

prtCnfgActivateLoop

Activate the desired loop on the port.
The agent will reset the variable to none(1).

Enumerationr/w

Enumerated Values:

1	mon
2	tue
3	wed
4	thu
5	fri
6	sat
7	sun

.1.3.6.1.4.1.164.3.7.2.1.1.1.5

prtCnfgClearLoop

Clear the desired loop from the port. The agent will
reset the variable to none(1)

Enumerationr/w

Constraints:
range: 1-3

.1.3.6.1.4.1.164.3.7.2.1.1.1.6

prtCnfgLoopStatus

The loop status at this port. The variable is a sum of 2**n where
n is as follows:
0 - Local Loop is on.
1 - Remote Loop is on.
2 - BONDING Loop is on.
If the variable is 0, there is no active loop.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.3.7.2.1.1.1.7

channelCnfgTable

table

.1.3.6.1.4.1.164.3.7.4.1 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk channelCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::channelCnfgTable'

A table containing configuration parameters for the channels.

channelCnfgEntry row .1.3.6.1.4.1.164.3.7.4.1.1

An entry in table channelCnfgTable.

Indexes

No indexes recorded

Column Syntax OID

chIndex

The channel index.

Integer32

.1.3.6.1.4.1.164.3.7.4.1.1.1

chCnfgUnlock

Unlock the channel (on). The agent resets the variable to off.

Enumerationr/w

.1.3.6.1.4.1.164.3.7.4.1.1.2

chCnfgPing

Ping the channel (on). The agent resets the variable to off.

Enumerationr/w

Enumerated Values:

1	ip
2	ipx
3	other

.1.3.6.1.4.1.164.3.7.4.1.1.3

channelStatTable

table

.1.3.6.1.4.1.164.3.7.4.2 · 1 row entry · 1 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk channelStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::channelStatTable'

A table containing status and statistics information for the channels.

channelStatEntry row .1.3.6.1.4.1.164.3.7.4.2.1

An entry in table channelStatTable.

Indexes

No indexes recorded

Column	Syntax	OID
chStatOperStatus The operational state of the channel based on a ping operation.	Enumeration	`.1.3.6.1.4.1.164.3.7.4.2.1.1`

radBridgeMaskTable

table

.1.3.6.1.4.1.164.4.1.3 · 1 row entry · 20 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radBridgeMaskTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radBridgeMaskTable'

Mask tables enable definition of forwarding restrictions and 
control of message flow in the internetwork. Each entry
in this table defines a mask statement consisting of up to 
three mask definitions and an action defined by 
radBridgeMaskOper. Different types of mask entries are supported, 
as defined by radBridgeMaskType.

radBridgeMaskEntry row .1.3.6.1.4.1.164.4.1.3.1

An entry in table radBridgeMaskTable.

Indexes

No indexes recorded

Column Syntax OID

radBridgeMaskType

Defines the type of mask entry.

Enumeration

Enumerated Values:

1	noStationOnLan
2	onTraffic
3	onDelayFromConnectionOnRequest
4	onManualDisConnect

.1.3.6.1.4.1.164.4.1.3.1.1

radBridgeMaskIfIndex

Specifies the if Index of the interface to which the mask is applied.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.3.1.2

radBridgeMaskNum

The Mask entry number, defined by its line number in the mask
table.

SNMPv2-SMIInteger32

Enumerated Values:

1	onPowerOn
2	whenAnyStationOnLan
3	onTraffic
4	onManualConnect

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.3.1.3

radBridgeMaskDest

Specifies the type of destination address carried by the frame
to which the mask will be applied. Unassigned-condition
deactivates the mask entry.

Enumerationr/w

.1.3.6.1.4.1.164.4.1.3.1.4

radBridgeMaskPat1

Describes the mask field which is either a 16 bit binary pattern,
or four digit hexadecimal pattern.

OctetStringr/w

.1.3.6.1.4.1.164.4.1.3.1.5

radBridgeMaskActiveBit1

Specifies the positions of the wild card characters (*)
in the radBridgeMaskPat1 field.

OctetStringr/w

.1.3.6.1.4.1.164.4.1.3.1.6

radBridgeMaskFrom1

Offset base of radBridgeMaskPat1 within the frame.
Net can be in some cases the data start point.

Enumerationr/w

.1.3.6.1.4.1.164.4.1.3.1.7

radBridgeMaskOffset1

Specifies the radBridgeMaskPat1 offset within the frame (in bytes) from
the base defined in by radBridgeMaskForm1.The mask offset is an even
decimal number in the range of 0 to 1518.

SNMPv2-SMIInteger32r/w

Constraints:
range: 4-4

.1.3.6.1.4.1.164.4.1.3.1.8

radBridgeMaskCond1

Specifies the logical condition of the mask pattern:

true - Condition is valid if at the position specified by
radBridgeMaskOffset1 the packet contains data that matches
the content of radBridgeMaskPa…

Enumerationr/w

Enumerated Values:

1	main
2	alternate

.1.3.6.1.4.1.164.4.1.3.1.9

radBridgeMaskPat2

Describes the mask field which is either a 16 bit binary pattern,
or four digit hexadecimal pattern.

OctetStringr/w

Constraints:
range: 6-6

.1.3.6.1.4.1.164.4.1.3.1.10

radBridgeMaskActiveBit2

Specifies the positions of the wild card characters (*)
in the radBridgeMaskPat2 field.

OctetStringr/w

.1.3.6.1.4.1.164.4.1.3.1.11

radBridgeMaskFrom2

Offset base of radBridgeMaskPat2 within the frame.
Net can be in some cases the data start point.

Enumerationr/w

.1.3.6.1.4.1.164.4.1.3.1.12

radBridgeMaskOffset2

Specifies the radBridgeMaskPat2 offset within the frame (in bytes) from
the base defined in by radBridgeMaskForm2.The mask offset is an even
decimal number in the range of 0 to 1518.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.3.1.13

radBridgeMaskCond2

Specifies the logical condition of the mask pattern:

true - Condition is valid if at the position specified by
radBridgeMaskOffset2 the packet contains data that matches
the content of radBridgeMaskPa…

Enumerationr/w

.1.3.6.1.4.1.164.4.1.3.1.14

radBridgeMaskPat3

Describes the mask field which is either a 16 bit binary pattern,
or four digit hexadecimal pattern.

OctetStringr/w

Enumerated Values:

1	static
2	dynamic
3	invalid
4	semiDynamic

.1.3.6.1.4.1.164.4.1.3.1.15

radBridgeMaskActiveBit3

Specifies the positions of the wild card characters (*)
in the radBridgeMaskPat3 field.

OctetStringr/w

Enumerated Values:

1	other
2	local
3	remote

.1.3.6.1.4.1.164.4.1.3.1.16

radBridgeMaskFrom3

Offset base of radBridgeMaskPat3 within the frame.
Net can be in some cases the data start point.

Enumerationr/w

.1.3.6.1.4.1.164.4.1.3.1.17

radBridgeMaskOffset3

Specifies the radBridgeMaskPat3 offset within the frame (in bytes) from
the base defined in by radBridgeMaskForm3. The mask offset is an even
decimal number in the range of 0 to 1518.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.3.1.18

radBridgeMaskCond3

Specifies the logical condition of the mask pattern:

true - Condition is valid if at the position specified by
radBridgeMaskOffset3 the packet contains data that matches
the content of radBridgeMaskPa…

Enumerationr/w

.1.3.6.1.4.1.164.4.1.3.1.19

radBridgeMaskOper

The type of action to be taken if the frame meets the
conditions of the mask.
noOp = disabled (mask remains on list, but is not active)
delete = mask is removed from the list.

Enumerationr/w

.1.3.6.1.4.1.164.4.1.3.1.20

radBridgeCODParamTable

table

.1.3.6.1.4.1.164.4.1.4.1 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radBridgeCODParamTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radBridgeCODParamTable'

The table of COD parameters

radBridgeCODEntry row .1.3.6.1.4.1.164.4.1.4.1.1

Each radBridgeCODEntry consists of the following parameters

Indexes

No indexes recorded

Column	Syntax	OID
radBridgeCODIfIndex The interface to which this COD entry is applicable.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.1.4.1.1.1`
radBridgeCODManualConnect The management station can start connection manually by setting this parameter	Enumerationr/w	`.1.3.6.1.4.1.164.4.1.4.1.1.2`
radBridgeCODMode In answer mode only one incoming call may be accepted at a time. Other nodes attempting to access the local modem will receive a busy signal until the connection is terminated. (Answer mode has no difficulty supporting …	Enumerationr/w Constraints: `range: 48-48`	`.1.3.6.1.4.1.164.4.1.4.1.1.3`
radBridgeCODConnectDelay The connect delay defines the minimum time period that the link must stay disconnected, between 2 succesive connections (in seconds).	SNMPv2-SMIInteger32r/w Constraints: `range: 4-4`	`.1.3.6.1.4.1.164.4.1.4.1.1.4`
radBridgeCODisConnectDelay The disconnect delay defines the minimum time period the link must stay connected, between 2 succesive disconnections (in seconds).	SNMPv2-SMIInteger32r/w Constraints: `range: 6-6`	`.1.3.6.1.4.1.164.4.1.4.1.1.5`
radBridgeCODImplicitSwitch The inplicit switch allows the user to ignore implicit triggers provided by the COD software.	Enumerationr/w	`.1.3.6.1.4.1.164.4.1.4.1.1.6`
radBridgeCODNumAccess The number of successful connections that have been established since the COD has been reset.	SNMPv2-SMICounter32 Constraints: `range: 1-16`	`.1.3.6.1.4.1.164.4.1.4.1.1.7`
radBridgeCODTotalConnecTime The sum of all the connect time intervals since the COD was reset.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.1.4.1.1.8`

radBridgeCODTimeTriggerTable

table

.1.3.6.1.4.1.164.4.1.4.2 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radBridgeCODTimeTriggerTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radBridgeCODTimeTriggerTable'

The table of COD parameters

radBridgeCODTimeTriggerEntry row .1.3.6.1.4.1.164.4.1.4.2.1

Each radBridgeCODTimeTriggerEntry consists of the following parameters

Indexes

No indexes recorded

Column	Syntax	OID
radBridgeCODTimeIfIndex The interface to which this COD Time Trigger entry is applicable.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.1.4.2.1.1`
radBridgeCODDay The day of the week in which the dial up connection operates.	Enumeration	`.1.3.6.1.4.1.164.4.1.4.2.1.2`
radBridgeCODTimeTriggerNum Every day of the week the user can configure 3 dial up connections.	Integer32	`.1.3.6.1.4.1.164.4.1.4.2.1.3`
radBridgeCODTimeTriggerFrom Time to start Dial Up connection, in format hh:mm.	SNMPv2-TCDisplayStringr/w Type Constraints: `range: 0..255` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.164.4.1.4.2.1.4`
radBridgeCODTimeTriggerTo Time to terminate Dial Up connection, in format HH:MM.	SNMPv2-TCDisplayStringr/w Type Constraints: `range: 0..255` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.164.4.1.4.2.1.5`
radBridgeCODTimeTriggerStatus The status of a table entry.	Enumerationr/w	`.1.3.6.1.4.1.164.4.1.4.2.1.6`

radBridgeCODTrafficTable

table

.1.3.6.1.4.1.164.4.1.4.3.1 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radBridgeCODTrafficTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radBridgeCODTrafficTable'

The table of COD Traffic trigger

radBridgeCODTrafficEntry row .1.3.6.1.4.1.164.4.1.4.3.1.1

Each radBridgeCODTrafficEntry consists of the following parameters.

Indexes

No indexes recorded

Column	Syntax	OID
radBridgeCODProtocolType The Protocol Type of the Traffic Table	Enumeration	`.1.3.6.1.4.1.164.4.1.4.3.1.1.1`
radBridgeCODTrafficTriggerStatus Command of Status of the Protocol Traffic Trigger	Enumerationr/w	`.1.3.6.1.4.1.164.4.1.4.3.1.1.2`

radBridgeCODCondTable

table

.1.3.6.1.4.1.164.4.1.4.4 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radBridgeCODCondTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radBridgeCODCondTable'

The table of COD Condition parameters

radBridgeCODCondEntry row .1.3.6.1.4.1.164.4.1.4.4.1

Each radBridgeCODCondEntry consists of the following parameters

Indexes

No indexes recorded

Column Syntax OID

radBridgeCODCondIfIndex

The interface, this COD entry is applicable to.

SNMPv2-SMIInteger32

Enumerated Values:

1	unknown
2	all
3	broadcast
4	multicast

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.4.4.1.1

radBridgeCODOriginateConnectCondition

This condition, allows the user to specify the
condition under which the link is connected.
The options are
onPowerOn - On power on.
whenAnyStationOnLan - When any station on lan.
onTraffic - …

Enumerationr/w

Enumerated Values:

1	false
2	true

.1.3.6.1.4.1.164.4.1.4.4.1.2

radBridgeCODOriginateDisConnectCondition

This condition allows the user to specify the
condition under which the link is disconnected.
The options are:
noStationOnLan - When there is no station on lan.
Counts 15 minutes from the point …

Enumerationr/w

.1.3.6.1.4.1.164.4.1.4.4.1.3

radBridgeCODOriginateDisConnectDelay

Delay time in seconds.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.4.4.1.4

radBridgeCODAnswerConnectCondition

CODCondAnswerConnect allows the user to specify
the condition under which the link is connected.
The options are:
onPowerOn - On power on.
whenAnyStationOnLan - When any station on lan.
onTraffic …

Enumerationr/w

Enumerated Values:

1	macAddress
2	netAddress
3	ipRange
4	appleAddress

.1.3.6.1.4.1.164.4.1.4.4.1.5

radBridgeCODSpecificOnTrafficOIDCondition

A reference to a specific entry in the
radBridgeMaskTable, which describes the
particular COD condition .
If Connect or Disconnect Conditions are not
onTraffic, its value should be set to the
OBJECT IDENTIFIER { 0 0 …

ObjectIdentifier

Enumerated Values:

1	false
2	true

.1.3.6.1.4.1.164.4.1.4.4.1.6

radBridgeCODDisConnectMinimunFramesNumber

Frames rate.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.4.4.1.7

radBridgeIPXRipTable

table

.1.3.6.1.4.1.164.4.1.5.2.6 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radBridgeIPXRipTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radBridgeIPXRipTable'

The routing table used by RIP to calculate routes to remote
desination networks.

radBridgeIPXRipTableEntry row .1.3.6.1.4.1.164.4.1.5.2.6.1

The routing information for one of this entity's destination networks.

Indexes

No indexes recorded

Column Syntax OID

radBridgeIPXRipDestNetwork

The destination network address to which this entry's
routing information pertains.

OctetString

Enumerated Values:

1	false
2	true

.1.3.6.1.4.1.164.4.1.5.2.6.1.1

radBridgeIPXRipPolicy

A value specifying the precidence of the route. A value of
zero means that the route is the best route, a value of one
means that the route is the second best route and so on.

Enumeration

Enumerated Values:

1	unknown
2	ipxRip
3	ipxSap
4	ipxSpx
5	ipUdp
6	ipTcp
7	ipIcmp
8	ipxNcp
9	ipxWan
10	ipxEco
11	ipxErr
12	ipxPep

.1.3.6.1.4.1.164.4.1.5.2.6.1.2

radBridgeIPXRipForwardingRouter

The IPX node address of the next hop (router) for the
entry's associated destination network.

OctetStringr/w

Enumerated Values:

1	false
2	true

.1.3.6.1.4.1.164.4.1.5.2.6.1.3

radBridgeIPXRipNIC

An interface identifier specifying what IPX interface the
next hop can be found on.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.5.2.6.1.4

radBridgeIPXRipTickMetric

The metric, in terms of transit time, associated with the route
given by the entry. This time is in terms of 1/18ths of a
second.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	false
2	true

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.5.2.6.1.5

radBridgeIPXRipHopMetric

The metric, in terms of distance , associated with the route
given by the entry.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.5.2.6.1.6

radBridgeIPXRipAgingTime

The last time that the entry was updated. The time will be
provided in terms of the MIB-I object sysUpTime.

RFC1155-SMITimeTicks

Enumerated Values:

1	false
2	true

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.5.2.6.1.7

radBridgeIPXRipValueStatus

The entry status value; whether the entry is permanent (added
statically), reachable or unreachable. In the latter two cases
it would be added by RIP. A semiDynamic entry is an entry
enterd manualy by the user and can …

Enumerationr/w

Enumerated Values:

1	block
2	forward
3	route
4	forward-route
5	high-priority
6	noOp
7	delete
8	smartMask

.1.3.6.1.4.1.164.4.1.5.2.6.1.8

radBridgeIPXRipForwardType

The type of route. Note that local(2) refers to a route for which the
next hop is the final destination; remote(3) refers to a route
for which the next hop is not the final destination.

Enumerationr/w

.1.3.6.1.4.1.164.4.1.5.2.6.1.9

radBridgeIPXRipInfTable

table

.1.3.6.1.4.1.164.4.1.5.2.7 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radBridgeIPXRipInfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radBridgeIPXRipInfTable'

The RIP interface table.

radBridgeIPXRipInfEntry row .1.3.6.1.4.1.164.4.1.5.2.7.1

Each entry corresponds to one ifindex.

Indexes

No indexes recorded

Column	Syntax	OID
radBridgeIPXRipInfIfIndex This value of Ifindex is same as radBridgeIPXIfIndex in the IPX Interface Table.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.1.5.2.7.1.1`
radBridgeIPXRipInfBcastUpdate The RIP periodic update interval, in seconds. Zero value corresponds to infinite interval.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.1.5.2.7.1.2`
radBridgeIPXRipInfAgeMultiplier The holding multiplier for information received in RIP periodic updates. Zero value corresponds to infinite aging time.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.1.5.2.7.1.3`

radBridgeIPXSapTable

table

.1.3.6.1.4.1.164.4.1.5.3.6 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radBridgeIPXSapTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radBridgeIPXSapTable'

The Server Information table is used by SAP to store information
of services which are available on the internetwork.

radBridgeIPXSapTableEntry row .1.3.6.1.4.1.164.4.1.5.3.6.1

The server information for one of this entity's server entries.

Indexes

No indexes recorded

Column	Syntax	OID
radBridgeIPXSapServerType The type of the server for which this entry pertains.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.1.5.3.6.1.1`
radBridgeIPXSapName The name of the server for which this entry pertains.	OctetString	`.1.3.6.1.4.1.164.4.1.5.3.6.1.2`
radBridgeIPXSapNetwork The IPX network address of the host on which this server exists.	OctetStringr/w	`.1.3.6.1.4.1.164.4.1.5.3.6.1.3`
radBridgeIPXSapNode The IPX node address of the host on which this server exists.	OctetStringr/w	`.1.3.6.1.4.1.164.4.1.5.3.6.1.4`
radBridgeIPXSapSocket The IPX socket number that is being used by the server to which this entry pertains.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.1.5.3.6.1.5`
radBridgeIPXSapHopsToServer The number of hops to the entity on which this server exists.	Integer32r/w	`.1.3.6.1.4.1.164.4.1.5.3.6.1.6`
radBridgeIPXSapNIC An Network Interface Card identifier specifying what IPX interface the next hop can be found on.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.1.5.3.6.1.7`
radBridgeIPXSapAgingTime The last time that the entry was updated. The time will be provided in terms of the MIB-I object sysUpTime.	RFC1155-SMITimeTicks Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.4.1.5.3.6.1.8`
radBridgeIPXSapStatus The status of the entry.	Enumerationr/w	`.1.3.6.1.4.1.164.4.1.5.3.6.1.9`

radBridgeIPXSapInfTable

table

.1.3.6.1.4.1.164.4.1.5.3.7 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radBridgeIPXSapInfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radBridgeIPXSapInfTable'

The Sap interface table.

radBridgeIPXSapInfEntry row .1.3.6.1.4.1.164.4.1.5.3.7.1

Each entry corresponds to one ifindex.

Indexes

No indexes recorded

Column	Syntax	OID
radBridgeIPXSapInfIfIndex This value of Ifindex is same as radBridgeIPXIfIndex in the IPX Interface Table.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.1.5.3.7.1.1`
radBridgeIPXSapInfBcastUpdate The SAP periodic update interval, in seconds. Zero value corresponds to infinite interval.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.1.5.3.7.1.2`
radBridgeIPXSapInfAgeMultiplier The holding multiplier for information received in SAP periodic updates. Zero value corresponds to infinite aging time.	SNMPv2-SMIInteger32r/w Constraints: `range: 1-96`	`.1.3.6.1.4.1.164.4.1.5.3.7.1.3`

maskingTable

table

.1.3.6.1.4.1.164.4.1.6.3 · 1 row entry · 24 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk maskingTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::maskingTable'

This is the new masking scheme. 
Mask tables enable definition of forwarding restrictions and 
control of message flow in the internetwork. Each entry
in this table defines a mask statement and an action defined by 
maskingOperation.

maskingEntry row .1.3.6.1.4.1.164.4.1.6.3.1

Defines the contents of each line in the mask table.

Indexes

No indexes recorded

Column Syntax OID

maskingType

Defines the type of mask entry.

Enumeration

.1.3.6.1.4.1.164.4.1.6.3.1.1

maskingIfIndex

Specifies the ifIndex of the interface to which the mask is applied.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.6.3.1.2

maskingIndex

An index to the masking table. This number should not be greater than maskingMaxEntries

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.6.3.1.3

maskingProtocolType

The base protocol for masking. IPX, IP, others.

Enumerationr/w

.1.3.6.1.4.1.164.4.1.6.3.1.4

maskingSmartMaskOID

A reference to a specific Smart mask table (old radBridgeMaskTable)
which enables a more specific mask type.
If this information is not available, its value
should be set to the OBJECT IDENTIFIER { 0 0 }.

ObjectIdentifier

.1.3.6.1.4.1.164.4.1.6.3.1.5

maskingFrameType

Enables the user to decide about frame type
* all frame
* just broadcast
* just multicast.

Enumerationr/w

.1.3.6.1.4.1.164.4.1.6.3.1.6

maskingFrameTypeCondition

Specifies the logical condition of the mask pattern:

true - Condition is valid if at the position specified by
maskingFrameType the packet contains data that matches
the content of maskingFrameType.…

Enumerationr/w

.1.3.6.1.4.1.164.4.1.6.3.1.7

maskingSourceAddress

The source address is according to the maskingMacOrNet and
maskingProtocolType variables.
In case of 'MAC' enter 6 bytes (48 bit) of source address.
In case of 'NET'
if the maskingProtocolType is IP, this is t…

GenAddressr/w

Type Constraints:
range: 12

.1.3.6.1.4.1.164.4.1.6.3.1.8

maskingSourceActiveBits

Specifies the positions of the wild card characters (*)
in the maskingSourceAddress field. Only the 1's bit will be taken in
considerations.

GenAddressr/w

Type Constraints:
range: 12

.1.3.6.1.4.1.164.4.1.6.3.1.9

maskingSourceMacOrNet

The variable maskingSourceAddress and maskingSourceActiveBits
will be treated as MAC, or NET address.
- If maskingProtocolType = 'all', 'sna', 'netbios', dec or
'unknown', the maskingSourceMacOrNet can be macAddress…

Enumerationr/w

.1.3.6.1.4.1.164.4.1.6.3.1.10

maskingSourceCondition

Specifies the logical condition of the mask pattern:

true - Condition is valid if at the position specified by
maskingSourceAddress (in conjunction with maskingSourceActiveBits)
the …

Enumerationr/w

.1.3.6.1.4.1.164.4.1.6.3.1.11

maskingDestAddress

If maskingFrameType = broadcast or multicast, this object
is NOT APPLICABLE.
If maskingFrameType = all or unknown, this object is
applicable.
The destination address is according to the maskingMacOrNet and maskingProto…

GenAddressr/w

Type Constraints:
range: 12

.1.3.6.1.4.1.164.4.1.6.3.1.12

maskingDestActiveBits

If maskingFrameType = broadcast or multicast, this object
is NOT APPLICABLE.
If maskingFrameType = all or unknown, this object is
applicable.
Specifies the positions of the wild card characters (*)
in the maskingDe…

GenAddressr/w

Type Constraints:
range: 12

.1.3.6.1.4.1.164.4.1.6.3.1.13

maskingDestMacOrNet

If maskingFrameType = broadcast or multicast, this object
is NOT APPLICABLE.
If maskingFrameType = all or unknown, this object is
applicable.
- If maskingProtocolType = 'all', 'sna', 'netbios', dec or
'unknown', the…

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.4.1.6.3.1.14

maskingDestCondition

If maskingFrameType = broadcast or multicast, this object
is NOT APPLICABLE.
If maskingFrameType = all or unknown, this object is
applicable.
Specifies the logical condition of the mask pattern:

true - …

Enumerationr/w

.1.3.6.1.4.1.164.4.1.6.3.1.15

maskingLowLevelProt

This field is set in conjunction with the maskingProtocolType variable.
This variable specifies the low level protocol.
The IPX socket entered in maskingDestAddress has priority
over the value of maskingLowLevelProt, w…

Enumerationr/w

Constraints:
range: 0-32

.1.3.6.1.4.1.164.4.1.6.3.1.16

maskingLowLevelProtCondition

Specifies the logical condition of the mask pattern:

true - Condition is valid if at the position specified by
maskingLowLevelProt the packet contains data that matches
the content of maskingLowLeve…

Enumerationr/w

.1.3.6.1.4.1.164.4.1.6.3.1.17

maskingHighLevelProt

This field is set in connection to the maskingProtocolType variable.
This variable specifies the high level protocols (application).
As for today it supports just IP protocol stack.
The object's value is a sum of the fo…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.6.3.1.18

maskingHighLevelProtCondition

Specifies the logical condition of the mask pattern:

true - Condition is valid if at the position specified by
maskingHighLevelProt the packet contains data that matches
the content of maskingHi…

Enumerationr/w

.1.3.6.1.4.1.164.4.1.6.3.1.19

maskingPortNum

The port number is the same as in high level protocol. It
specifies the dest. port in IP case or the dest. socket
in case of IPX & apple protocols.
IP - This object is applicable only if none (0) value was selecte…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.6.3.1.20

maskingPortNumCondition

Specifies the logical condition of the mask pattern:

true - Condition is valid if at the position specified by
maskingPortNum the packet contains data that matches
the content of maskingPortNum.…

Enumerationr/w

.1.3.6.1.4.1.164.4.1.6.3.1.21

maskingOperation

The type of action to be taken if the frame meets the
conditions of the mask.
noOp = disabled (mask remains on list, but is not active)
delete = mask is removed from the list.
smartMask = the operation and desti…

Enumerationr/w

.1.3.6.1.4.1.164.4.1.6.3.1.22

maskingSrcPortNum

The source port number.
For IP: No Condition.
For IPX: This object is applicable only if the socket entered in
maskingSourceAddress is don't care (00) and maskingLowLevelProt
is NOT ipxRip or ipxS…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.6.3.1.23

maskingSrcPortNumCondition

The same as 'maskingPortNumCondition'.
Relates to source port.

Enumerationr/w

.1.3.6.1.4.1.164.4.1.6.3.1.24

radBridgeCurrentTable

table

.1.3.6.1.4.1.164.4.1.7.1 · 1 row entry · 14 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radBridgeCurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radBridgeCurrentTable'

The RAD Bridge Current table.

radBridgeCurrentEntry row .1.3.6.1.4.1.164.4.1.7.1.1

An entry in the RAD Bridge Current table.

Indexes

No indexes recorded

Column Syntax OID

radBridgeCurrentIndex

The index of the Bridge interface or Bridge Port.
It may be ifIndex.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.7.1.1.1

radBridgeCurrentIngressFilteringDiscardedFrames

The counter associated with the number of Discarded
Frames upon Ingress Filtering, encountered by a Bridge
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.1.1.2

radBridgeCurrentFrameTypeDiscardedFrames

The counter associated with the number of Discarded
Frames upon Frame Type and Tagging Mismatch, encountered
by a Bridge interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Constraints:
range: 1-2147483647

.1.3.6.1.4.1.164.4.1.7.1.1.3

radBridgeCurrentRxCorrectFrames

The counter associated with the number of Received Correct Frames,
encountered by a Bridge Port in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.1.1.4

radBridgeCurrentRxCorrectBytes

The counter associated with the number of Received Correct Bytes,
encountered by a Bridge Port in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.1.1.5

radBridgeCurrentRxCorrectBytesHCOverflow

The counter associated with the number of times the associated
radBridgeCurrentRxCorrectBytes counter has overflowed.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.1.1.6

radBridgeCurrentRxBcastFrames

The counter associated with the number of Received Broadcast Frames,
encountered by a Bridge Port in the current 15 minute interval.

SNMPv2-SMIGauge32

Enumerated Values:

1	notApplicable
2	vlanTag
3	dscp
4	dscpAndVlanTag
5	vlanTagAndDscp
6	none
7	tos
8	perPort
9	ipPrecedence
10	dsField
11	vlanTagAndTos
12	tosAndVlanTag
13	vlanTagAndIpPrecedence
14	ipPrecedenceAndVlanTag
15	vlanTagAndDsField
16	dsFieldAndVlanTag

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.1.1.7

radBridgeCurrentRxMcastFrames

The counter associated with the number of Received Multicast Frames,
encountered by a Bridge Port in the current 15 minute interval.

SNMPv2-SMIGauge32

Enumerated Values:

1	notApplicable
2	wfq
3	sp
4	atmCos

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.1.1.8

radBridgeCurrentTxCorrectFrames

The counter associated with the number of Transmitted Correct Frames,
encountered by a Bridge Port in the current 15 minute interval.

SNMPv2-SMIGauge32

Enumerated Values:

2	none
3	port

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.1.1.9

radBridgeCurrentTxCorrectBytes

The counter associated with the number of Transmitted Correct Bytes,
encountered by a Bridge Port in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.1.1.10

radBridgeCurrentTxCorrectBytesHCOverflow

The counter associated with the number of times the associated
radBridgeCurrentTxCorrectBytes counter has overflowed.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.1.1.11

radBridgeCurrentTxBcastFrames

The counter associated with the number of Transmitted Broadcast Frames,
encountered by a Bridge Port in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.1.1.12

radBridgeCurrentTxMcastFrames

The counter associated with the number of Transmitted Multicast Frames,
encountered by a Bridge Port in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.1.1.13

radBridgeCurrentTxDropFrames

The counter associated with the number of Transmitted Dropped Frames,
encountered by a Bridge Port in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.1.1.14

radBridgeIntervalTable

table

.1.3.6.1.4.1.164.4.1.7.2 · 1 row entry · 15 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radBridgeIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radBridgeIntervalTable'

The RAD Bridge Interval table.

radBridgeIntervalEntry row .1.3.6.1.4.1.164.4.1.7.2.1

An entry in the RAD Bridge Interval table.

Indexes

No indexes recorded

Column Syntax OID

radBridgeIntervalIndex

The index of the bridge interface or Bridge Port.
It may be ifIndex.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.7.2.1.1

radBridgeIntervalNumber

A number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals exist).

Integer32

.1.3.6.1.4.1.164.4.1.7.2.1.2

radBridgeIntervalIngressFilteringDiscardedFrames

The counter associated with the number of Discarded
Frames upon Ingress Filtering, encountered by a
Bridge interface in one of the previous 96, individual
15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.2.1.3

radBridgeIntervalFrameTypeDiscardedFrames

The counter associated with the number of Discarded
Frames upon Frame Type and Tagging Mismatch, encountered
by a Bridge interface in one of the previous 96, individual
15 minute, intervals.

SNMPv2-SMIGauge32

Enumerated Values:

1	notApplicable
2	unmodify
3	tag
4	stack

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.2.1.4

radBridgeIntervalRxCorrectFrames

The counter associated with the number of Received Correct Frames,
encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.

SNMPv2-SMIGauge32

Enumerated Values:

1	notApplicable
2	no
3	yes

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.2.1.5

radBridgeIntervalRxCorrectBytes

The counter associated with the number of Received Correct Bytes,
encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.2.1.6

radBridgeIntervalRxCorrectBytesHCOverflow

The counter associated with the number of times the associated
radBridgeIntervalRxCorrectBytes counter has overflowed.

SNMPv2-SMIGauge32

Enumerated Values:

1	notApplicable
2	no
3	yes

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.2.1.7

radBridgeIntervalRxBcastFrames

The counter associated with the number of Received Broadcast Frames,
encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.

SNMPv2-SMIGauge32

Enumerated Values:

2	none
3	stacking
4	stripping

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.2.1.8

radBridgeIntervalRxMcastFrames

The counter associated with the number of Received Multicast Frames,
encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.

SNMPv2-SMIGauge32

Enumerated Values:

2	none
3	stacking
4	stripping

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.2.1.9

radBridgeIntervalTxCorrectFrames

The counter associated with the number of Transmitted Correct Frames,
encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.

SNMPv2-SMIGauge32

Enumerated Values:

1	notApplicable
2	no
3	yes

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.2.1.10

radBridgeIntervalTxCorrectBytes

The counter associated with the number of Transmitted Correct Bytes,
encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.2.1.11

radBridgeIntervalTxCorrectBytesHCOverflow

The counter associated with the number of times the associated
radBridgeIntervalTxCorrectBytes counter has overflowed.

SNMPv2-SMIGauge32

Enumerated Values:

2	disable
3	enable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.2.1.12

radBridgeIntervalTxBcastFrames

The counter associated with the number of Transmitted Broadcast Frames,
encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.2.1.13

radBridgeIntervalTxMcastFrames

The counter associated with the number of Transmitted Multicast Frames,
encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.7.2.1.14

radBridgeIntervalTxDropFrames

The counter associated with the number of Transmitted Dropped Frames,
encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.

SNMPv2-SMIGauge32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.4.1.7.2.1.15

radBridgePortBaseVlanTable

table

.1.3.6.1.4.1.164.4.1.8.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radBridgePortBaseVlanTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radBridgePortBaseVlanTable'

A table containing static configuration information for
each VLAN configured into the device by  management.
All entries are permanent and will
be restored after the device is reset.

radBridgePortBaseVlanEntry row .1.3.6.1.4.1.164.4.1.8.1.1

Static information for a VLAN configured into the
device by (local or network) management.

Indexes

No indexes recorded

Column Syntax OID

radBridgePortBaseVlanCnfgIdx

This object indicates the Idx of the Agent Cnfg the following
objects refer.
255=Temporary Cnfg (when relevant,
Set is done only to this configuration).
For Agents that support only one configuration,
this object wil…

Integer32

Constraints:
range: 10-1000000

.1.3.6.1.4.1.164.4.1.8.1.1.1

radBridgePortBaseVlanIdx

Index of the port based VLAN.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.8.1.1.2

radBridgePortBaseVlanName

An administratively assigned string, which may be used
to identify the the port based VLAN.

OctetStringr/w

.1.3.6.1.4.1.164.4.1.8.1.1.3

radBridgePortBaseVlanEgressPorts

The set of ports which are permanently assigned to the
egress list for this port based VLAN by management.
The default value of this object is a string of zeros.

Q-BRIDGE-MIBPortListr/w

Enumerated Values:

1	notApplicable
2	disable
3	enabled
4	vlanBased

.1.3.6.1.4.1.164.4.1.8.1.1.4

radBridgePortBaseVlanVirtualGroups

The set of Virtual Groups which are permanently assigned to
this port based VLAN by management.
(read Virtual Group instead of port in PortList Textual Convention)
The default value of this object is a string of zeros.

Q-BRIDGE-MIBPortListr/w

.1.3.6.1.4.1.164.4.1.8.1.1.5

radBridgePortBaseVlanRowStatus

This object enable user to
create/delete entries in this table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.4.1.8.1.1.6

radBridgePortBaseVlanMng

This object allows user to enable/disable
management traffic on this VLAN.
disable - only non-management data is allowed.
enable - mixture of management traffic 0with other
types of data is allowed.

Enumerationr/w

.1.3.6.1.4.1.164.4.1.8.1.1.7

radBridgePortVlanMemberTable

table

.1.3.6.1.4.1.164.4.1.8.2 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radBridgePortVlanMemberTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radBridgePortVlanMemberTable'

The Bridge Ports-VLAN Membership table.
This table enables the user to assign:
- Several VLANs to a Port.
- Several Ports to a VLAN.

radBridgePortVlanMemberEntry row .1.3.6.1.4.1.164.4.1.8.2.1

An entry in the Bridge Ports-VLANs Memebership table.

Indexes

No indexes recorded

Column Syntax OID

radBridgePortVlanMemberBridgeIdx

This object indicates the Bridge Index.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.8.2.1.1

radBridgePortVlanMemberPortIdx

This object indicates the Bridge's Port Index.
For some cases, it can be used as the Port ofIndex.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.8.2.1.2

radBridgePortVlanMemberVlanId

This object indicates the VLAN ID.

SNMPv2-SMIInteger32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.4.1.8.2.1.3

radBridgePortVlanMemberRowStatus

This object enables the user to
create/delete entries in this table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.4.1.8.2.1.4

radBridgeGenFlowTable

table

.1.3.6.1.4.1.164.4.1.9.1 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radBridgeGenFlowTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radBridgeGenFlowTable'

A table containing static configuration information for
Bridge configured into the device by (local or
network) management.  All entries are permanent and will
be restored after the device is reset.

radBridgeGenFlowEntry row .1.3.6.1.4.1.164.4.1.9.1.1

Static information for a Bridge configured into the
device by management.

Indexes

No indexes recorded

Column Syntax OID

radBridgeGenFlowCnfgIdx

This object indicates the Idx of the
Agent Cnfg the following objects refer.
255=Temporary Cnfg (when relevant Set is done
only to this configuration).
For Agents that support only one configuration,
this object will…

Integer32

Constraints:
range: 100-1000

.1.3.6.1.4.1.164.4.1.9.1.1.1

radBridgeGenFlowIdx

For Agent having more than one bridge,
this index may be used as bridge index

SNMPv2-SMIInteger32

Constraints:
range: 0-65535

.1.3.6.1.4.1.164.4.1.9.1.1.2

radBridgeGenFlowRowStatus

This object enable user to
create/delete entries in this table.

SNMPv2-TCRowStatusr/w

Enumerated Values:

1	notApplicable
2	stp
3	rstp

Description:

.1.3.6.1.4.1.164.4.1.9.1.1.3

radBridgeGenFlowFloodOrBcastMaxRate

This object controls maximum Flooding or Broadcast Rate:
Max number of multicast along with unknown
or flooded unicast frames allowed to enter
any port.
The number can be presented either as percentage of bandwidth, …

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.9.1.1.4

radBridgeGenFlowQosMode

This object controls Quality of Service mode.
User may select which field(s)
(in case of fields - which one has precedence)
will affect prioritization of data between egress queues.

Enumerationr/w

.1.3.6.1.4.1.164.4.1.9.1.1.5

radBridgeGenFlowSchedulingMode

This object controls which scheduling mode is used:
Weighted Fair Queuing (WFQ) scheme,
Strict Priority (SP)
or ATM CoS

Enumerationr/w

.1.3.6.1.4.1.164.4.1.9.1.1.6

radBridgeGenFlowBasicClassification

This object defines whether Classification based on Port should be
taken into account (either as default, or in addition to other
classifications).

Enumerationr/w

.1.3.6.1.4.1.164.4.1.9.1.1.7

radBridgeGenFlowMulticastTrafficClass

The Traffic Class the received Multicast frame is mapped to.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.9.1.1.8

radBridgeGenFlowBroadcastTrafficClass

The Traffic Class the received Broadcast frame is mapped to.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.9.1.1.9

radBridgeGenFlowUnkownUnicastTrafficClass

The Traffic Class the received
Unkonwn Unicast frame is mapped to.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.9.1.1.10

radBridgeDot1qVlanStaticTable

table

.1.3.6.1.4.1.164.4.1.9.2 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radBridgeDot1qVlanStaticTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radBridgeDot1qVlanStaticTable'

A table containing static configuration information for
each VLAN configured into the device by (local or
network) management.  All entries are permanent and will
be restored after the device is reset.

radBridgeDot1qVlanStaticEntry row .1.3.6.1.4.1.164.4.1.9.2.1

Static information for a VLAN configured into the
device by (local or network) management.

Indexes

No indexes recorded

Column	Syntax	OID
radBridgeDot1qVlanTaggedPorts The set of ports which should transmit egress packets for this VLAN as tagged.	Q-BRIDGE-MIBPortListr/w	`.1.3.6.1.4.1.164.4.1.9.2.1.1`
radBridgeDot1qVlanUnmodifiedPorts The set of ports which should transmit egress packets for this VLAN as unmodified.	Q-BRIDGE-MIBPortListr/w	`.1.3.6.1.4.1.164.4.1.9.2.1.2`
radBridgeDot1qVlanSplitHorizon When 'enable (3)', packets having this VLAN will not be switched back to other bridge ports which are members of this VLAN.	Enumerationr/w	`.1.3.6.1.4.1.164.4.1.9.2.1.3`

radDot1qPortVlanTable

table

.1.3.6.1.4.1.164.4.1.9.3 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radDot1qPortVlanTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radDot1qPortVlanTable'

A table containing control and status
information for VLAN configuration per port.

radDot1qPortVlanEntry row .1.3.6.1.4.1.164.4.1.9.3.1

Information controlling VLAN configuration for a port.
This is indexed by dot1dBasePort.

Indexes

No indexes recorded

Column Syntax OID

radDot1qPortStacking

This object indicates the port stacking operation:
unmodify (2) = Do not add Tag.
tag (3) = Add Tag to Untagged Frames.
stack (4) = Add Tag to all Frames.

Enumerationr/w

Enumerated Values:

1	flooding
2	forwarding

.1.3.6.1.4.1.164.4.1.9.3.1.1

radDot1qPortCopyOriginVlanPriority

This object indicates whether use the original VLAN Priority of the frame,
as the priority of the VLAN added by this port.

Enumerationr/w

.1.3.6.1.4.1.164.4.1.9.3.1.2

radDot1qPortDefaultVlanPriority

Default VLAN Frame priority of the VLAN added by this port.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.9.3.1.3

radDot1qPortTagStripping

This object indicates whether remove a tag from the frame on this port,
frame with double tag will remain with one tag and frame with
one tag will remain untagged.

Enumerationr/w

.1.3.6.1.4.1.164.4.1.9.3.1.4

radDot1qPortEgressTagHandling

This object indicates how is the Egress VLAN Tag processed.
It is mainly for use with Double Tagging.

Enumerationr/w

.1.3.6.1.4.1.164.4.1.9.3.1.5

radDot1qPortIngressTagHandling

This object indicates how is the Ingress VLAN Tag processed.
It is mainly for use with Double Tagging.

Enumerationr/w

.1.3.6.1.4.1.164.4.1.9.3.1.6

radDot1qPortReplaceVlanPriority

This object indicates whether for each received tagged frame on this Bridge Port -
VLAN Priority will be replaced by another Priority.
no(2) = no repacement
yes(3) = VLAN Priority will be replaced

Fo…

Enumerationr/w

Enumerated Values:

2	disabled
3	enabled

.1.3.6.1.4.1.164.4.1.9.3.1.7

radDot1qPortVlanEthType

This object indicates the Ethernet Type.
For some devices, it is applicable only when radDot1qPortStacking = stack.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.9.3.1.8

radDot1qPortVlanCnodeLevel1Agent

Specify if a Level 1 cNode agent is enabled or not for the bridge port.

Enumerationr/w

.1.3.6.1.4.1.164.4.1.9.3.1.9

radBridgeGenCfgTable

table

.1.3.6.1.4.1.164.4.1.9.4 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radBridgeGenCfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radBridgeGenCfgTable'

A table containing Bridge configuration parameters.

radBridgeGenCfgEntry row .1.3.6.1.4.1.164.4.1.9.4.1

Describes an entry in the radBridgeGenCfgTable.

Indexes

No indexes recorded

Column Syntax OID

radBridgeGenCfgIdx

This object indicates the Idx of the
Agent Cnfg the following objects refer.
255=Temporary Cnfg.
For Agents that support only one Configuration,
this object will be constant=1.

Integer32

Enumerated Values:

255	notAllocated

.1.3.6.1.4.1.164.4.1.9.4.1.1

radBridgeGenCfgIdx2

For Agents having more than one bridge,
this index may be used as bridge index

SNMPv2-SMIInteger32

Enumerated Values:

1	active
2	delete

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.9.4.1.2

radBridgeGenCfgBridgeAction

This variable enables the operator to perform one of the
specified actions on the tables maintained by the Bridge.
After performing the action, Agent will automatically
Set the value of this variable to noOp(255).

Enumerationr/w

.1.3.6.1.4.1.164.4.1.9.4.1.3

radBridgeAgingTimeSec

This variable duplicates scalar object
dot1dTpAgingTimeThe of BRIDGE-MIB with configuration index
and Bridge index.

It defines the timeout period in seconds for aging out
dynamically learned forwardi…

Integer32r/w

.1.3.6.1.4.1.164.4.1.9.4.1.4

radBridgeMngVlanId

This variable indicates the VLAN ID
used for remote management traffic.
0 = Not Applicable.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.9.4.1.5

radBridgeLoopDetectVlanId

This variable indicates the VLAN ID used for Loop Detection packets.
Valid values:
1 - 4095: VLAN ID
0 - Means that the Loop Detection is Disabled.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	synchronous
2	asynchronous
3	x25FRconfig
4	x25FRchannel
5	isdn
6	frameRelay
7	pcmcia
8	dm2wire
254	notExist
255	unknown

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.9.4.1.6

radBridgeSplitHorizon

This object configure 'split horizon' switching between bridge Ports.
- disable - normal (VLAN aware) bridge behavior.
- enable - all packets, regardless their VLAN, coming from user side
are blocked from being switch…

Enumerationr/w

Enumerated Values:

2	disable
3	enable
4	backup

.1.3.6.1.4.1.164.4.1.9.4.1.7

radBridgeEthType

Value of Ethertype field in Ethernet frame.
This field indicates which protocol is being transported
in an ethernet frame.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

2	off
3	on
255	unknown

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.1.9.4.1.8

radBridgeInvBasePortTable

table

.1.3.6.1.4.1.164.4.1.10.1 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radBridgeInvBasePortTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radBridgeInvBasePortTable'

An inversed table to dot1dBasePortTable 
from RFC1493 with reduced information.
This table index is known to the NMS and 
this way the needed information can be received
by just one Get command, instead of searching 
the entire dot1dBasePortTable (where it is an 
attribute).

radBridgeInvBasePortEntry row .1.3.6.1.4.1.164.4.1.10.1.1

The bridge port number for each bridge port
interface index.

Indexes

No indexes recorded

Column Syntax OID

radBridgeInvBasePortIfIndex

The value of the instance of the ifIndex object,
defined in MIB-II, for the interface corresponding
to this Bridge port.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.10.1.1.1

radBridgeInvBasePort

The Bridge port number.

SNMPv2-SMIInteger32

Enumerated Values:

2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.10.1.1.2

radBridgeStpCnfgTable

table

.1.3.6.1.4.1.164.4.1.11.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radBridgeStpCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radBridgeStpCnfgTable'

STP Configuration table. STP=Spanning Tree Protocol.  
It includes STP configurable parameters that in BRIDGE-MIB 
are scalars, while we need them per card/bridge/interface
	 and per different configurations.

radBridgeStpCnfgEntry row .1.3.6.1.4.1.164.4.1.11.1.1

An entry in the radBridgeStpCnfgTable.

Indexes

No indexes recorded

Column Syntax OID

radBridgeStpCnfgIdx1

This object indicates the Index of the Agent Configuration
the following objects refer to.
For Agents that support more than one configuration:
255=Temporary Cnfg ; Set can be done only to this configuration.
For A…

Integer32

Enumerated Values:

1	unknown
2	proprietary
3	terminalServer
30	slip
31	cSlip
40	ppp
41	rfc1490
42	hdlcFraming
43	mlPpp

.1.3.6.1.4.1.164.4.1.11.1.1.1

radBridgeStpCnfgIdx2

For Agents having the table objects per Card/Bridge/Interface
this will be the index of the Card/Bridge/Interface used.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.11.1.1.2

radBridgeStpCnfgForwardDelay

The value that the bridge of radBridgeStpCnfgIdx2 uses for
Forward Delay when this bridge is acting as the root. Note that
the range for this parameter is related to the value of
radBridgeStpCnfgMaxAge (according to 8…

Integer32r/w

.1.3.6.1.4.1.164.4.1.11.1.1.3

radBridgeStpCnfgMaxAge

The value that the bridge of radBridgeStpCnfgIdx2 uses for
MaxAge when this bridge is acting as the root. Note that
the range for this parameter is related to the value of
radBridgeStpCnfgHelloTime (according to 802.1…

Integer32r/w

Enumerated Values:

1	notApplicable
2	disable
3	enableAll

.1.3.6.1.4.1.164.4.1.11.1.1.4

radBridgeStpCnfgHelloTime

The value that the bridge of radBridgeStpCnfgIdx2 uses for
Hello Time when this bridge is acting as the root. The granularity
of this timer is specified by 802.1D-1990 to be 1 second. An agent
may return a badValue …

Integer32r/w

.1.3.6.1.4.1.164.4.1.11.1.1.5

radBridgeStpCnfgPriority

The value of the write-able portion of the Bridge ID, i.e., the first
two octets of the (8 octet long) Bridge ID, per radBridgeStpCnfgIdx2
instance.

Integer32r/w

Enumerated Values:

1	notApplicable
2	noRoutingProtocol
3	rip1
4	rip2
5	rip1OrRip2
6	ospf

.1.3.6.1.4.1.164.4.1.11.1.1.6

radBridgeStpCnfgStpVersion

This object determines the STP version used:
stp - usual Spanning Tree Protocol.
rstp - Rapid Spanning Tree Protocol.

Enumerationr/w

.1.3.6.1.4.1.164.4.1.11.1.1.7

radBridgeStpStatTable

table

.1.3.6.1.4.1.164.4.1.11.2 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radBridgeStpStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radBridgeStpStatTable'

STP Status table. STP=Spanning Tree Protocol.
It includes STP status parameters that in BRIDGE-MIB 
are scalars, while we need them per card/bridge/interface.
For devices that have several configurations, this table is for Status
of the Active configuration.

radBridgeStpStatEntry row .1.3.6.1.4.1.164.4.1.11.2.1

An entry in the radBridgeStpStatTable.

Indexes

No indexes recorded

Column Syntax OID

radBridgeStpStatIdx

For Agents having the table objects per Card/Bridge/Interface
this will be the index of the Card/Bridge/Interface used.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.11.2.1.1

radBridgeStpStatForwardDelay

This time value, measured in units of hundredths of a second,
controls how fast a port changes its spanning state when moving
towards the Forwarding state. The value determines how long the port
stays in each of the …

BRIDGE-MIBTimeout

.1.3.6.1.4.1.164.4.1.11.2.1.2

radBridgeStpStatMaxAge

The maximum age of Spanning Tree Protocol information learned
from the network on any port before it is discarded, in units
of hundredths of a second. This is the actual value that this
bridge is currently using.

BRIDGE-MIBTimeout

Enumerated Values:

1	unknown
2	none
3	fail
4	connect
5	wait
6	down

.1.3.6.1.4.1.164.4.1.11.2.1.3

radBridgeStpStatHelloTime

The amount of time between the transmission of Configuration
bridge PDUs by this node on any port when it is the root of
the spanning tree or trying to become so, in units of hundredths
of a second. This is the actua…

BRIDGE-MIBTimeout

Enumerated Values:

1	tre1
2	tre8
3	tre1D
4	tre8D
5	tre8M
6	rrTre
7	rrTre1D
8	rrTre8D
9	iTre1
10	iTre2
11	mpTre8
12	kTre8
13	treRasA
14	treRasS
15	trePCAsync
16	trePCSync
17	mbe1
18	mbe8
19	mbe1D
20	mbe8D
21	ete8M
22	iEre1
23	iEe2
24	mpMbe8
25	kMbe8
26	mbePCAsync
27	mbePCSync
28	mbeRasA
29	mbeRasS
255	other

.1.3.6.1.4.1.164.4.1.11.2.1.4

radBridgeStpStatDesignatedRoot

The bridge identifier of the root of the spanning tree as determined
by the Spanning Tree Protocol as executed by this node. This value
is used as the Root Identifier parameter in all Configuration
Bridge PDUs origin…

BRIDGE-MIBBridgeId

Type Constraints:
range: 8

.1.3.6.1.4.1.164.4.1.11.2.1.5

radBridgeStpStatRootCost

The cost of the path to the root as seen from this bridge.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.11.2.1.6

radBridgePortCnfgTable

table

.1.3.6.1.4.1.164.4.1.13.1 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radBridgePortCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radBridgePortCnfgTable'

The Bridge Port Configuration Table.

radBridgePortCnfgEntry row .1.3.6.1.4.1.164.4.1.13.1.1

An entry in the table.

Indexes

No indexes recorded

Column Syntax OID

radBridgePortCnfgIdx

The first index of the table.
It can serve for Configuration index, Bridge index or other.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.13.1.1.1

radBridgePortCnfgPrtIdx

This object indicates the Bridge Port index.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.13.1.1.2

radBridgePortCnfgMaxMacAddr

This object indicates the maximum number of total MAC Addresses
(static and learned) supported by this Bridge Port.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.13.1.1.3

radBridgePortCnfgMngFlow

This object indicates whether this Bridge Port
is dedicated for management flow.

Enumerationr/w

.1.3.6.1.4.1.164.4.1.13.1.1.4

radBridgePortCnfgMcastMode

This object indicates this Bridge Port's Multicast Mode:
flooding (1) - flood multicast MAC addresses
forwarding (2) - forward multicast MAC addresses to the subnet indicated.

Enumerationr/w

.1.3.6.1.4.1.164.4.1.13.1.1.5

radBridgePortCnfgDefaultVpi

This object indicates the VPI of this Bridge Port's Default VCL.
An incoming frame with priority that is not assigned to any VCL
will be transferred to the Default VCL.

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.13.1.1.6

radBridgePortCnfgDefaultVci

This object indicates the VCI of this Bridge Port's Default VCL.
An incoming frame with priority that is not assigned to any VCL
will be transferred to the Default VCL.

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.13.1.1.7

radBridgePortCnfgStatVlanId

This object indicates the selected VlanId of the bridge port
on which statistics are being collected.
0=no Statistics collected for VLAN on this bridge port.

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.13.1.1.8

radBridgePortCnfgIngressMtu

The size of the largest packet which can be received
on the interface, specified in octets.

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.13.1.1.9

radBridgePortCnfgEgressMtu

The size of the largest packet which can be sent
on the interface, specified in octets.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.13.1.1.10

radBridgePortCnfgDot1x

This feature is currently supported via the variable ethIfTable.ethDot1xEnable.
Determnines if the Port-Based Network Access Protocol
(IEEE-802.1x)is enabled for the bridge Port.

Enumerationr/w

.1.3.6.1.4.1.164.4.1.13.1.1.11

radBridgePortCnfgMappingProfile

This attribute defines the Queue Mapping Profile ID(cosProfileTable) assigned
to this Bridge Port.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.1.13.1.1.12

lanrangerBootPTable

table

.1.3.6.1.4.1.164.4.2.1.6.4.4 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk lanrangerBootPTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::lanrangerBootPTable'

A list of BootP entries.  The number of entries is up to
BootP current entries, according to the LANRANger model.

lanrangerBootPEntry row .1.3.6.1.4.1.164.4.2.1.6.4.4.1

BootP parameters per entry of the BootP table.

Indexes

No indexes recorded

Column Syntax OID

lanrangerBootPIpAddress

BootP Ip Address.

RFC1155-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.164.4.2.1.6.4.4.1.1

lanrangerBootPIfIndex

The number is the same as the ifIndex of the link.

Enumeration

.1.3.6.1.4.1.164.4.2.1.6.4.4.1.2

lanrangerBootPOperation

This object indicates the status of this entry.
active(1) - this entry is currently in use
and will remain so even after the next
reset of the LANRANger.
delete(2) - writing this value to the obj…

Enumerationr/w

Enumerated Values:

1	x25FRChannel
2	x25FRConfig

.1.3.6.1.4.1.164.4.2.1.6.4.4.1.3

lanrangerLinkTable

table

.1.3.6.1.4.1.164.4.2.2.1 · 1 row entry · 16 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk lanrangerLinkTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::lanrangerLinkTable'

A list of link entries.  The number of entries is
up to 8, according to the LANRANger model.

lanrangerLinkEntry row .1.3.6.1.4.1.164.4.2.2.1.1

LANRANger-specific parameter values for a link.

Indexes

No indexes recorded

Column Syntax OID

lanrangerLinkIndex

A unique value for each link, equal to the value of ifIndex.
The value for each link must remain constant at least
from one re-initialization of the network management agent to
the next.

SNMPv2-SMIInteger32

Enumerated Values:

1	none
2	odd
3	even
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.2.2.1.1.1

lanrangerLinkType

The link type .

Enumerationr/w

Enumerated Values:

1	one
2	two
255	notApplicable

.1.3.6.1.4.1.164.4.2.2.1.1.2

lanrangerLinkState

The link is disabled, enabled or backup.

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.4.2.2.1.1.3

lanrangerLinkDTRMode

The link DTR mode.

Enumeration

.1.3.6.1.4.1.164.4.2.2.1.1.4

lanrangerLinkStatus

The link physical status .

Enumeration

.1.3.6.1.4.1.164.4.2.2.1.1.5

lanrangerLinkConnectionStatus

The link connection status.

Enumeration

Enumerated Values:

2	compressionOff
3	compressionOn

.1.3.6.1.4.1.164.4.2.2.1.1.6

lanrangerLinkNumOfLogLinks

The number of logical links on this physical link.
0 = noLogicalLink

SNMPv2-SMIInteger32

Enumerated Values:

2	compressionOff
3	compressionOn

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.2.2.1.1.7

lanrangerLinkReset

Setting this attribute to ON will reset the link . Upon completion the value will be set to OFF

Enumerationr/w

Enumerated Values:

1	disable
2	noHistory
3	lCB
4	sequence
5	extended

.1.3.6.1.4.1.164.4.2.2.1.1.8

lanrangerLinkRxMaskedFrames

The number of masked frames received on this physical link.

SNMPv2-SMICounter32

Enumerated Values:

1	noneNone
2	chapNone
3	chapPap
4	chapChap
5	papNone
6	papPap

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.2.2.1.1.9

lanrangerLinkLayer2Type

The link layer 2 type indicates whether the link is Bridge
or Router and specifies the Router's type.

Enumerationr/w

Enumerated Values:

1	host
2	guest

.1.3.6.1.4.1.164.4.2.2.1.1.10

lanrangerLinkLayer3Type

The link layer 3 type indicates the protocol type.

Enumerationr/w

Constraints:
range: 0-36

.1.3.6.1.4.1.164.4.2.2.1.1.11

lanrangerBackupLink

The backup link interface index located in the two LSB bytes.
If the link is FR type, the two MSB will contain a DLCi number.
For other link types the two MSB will equal to 0.

SNMPv2-SMIInteger32r/w

Constraints:
range: 0-36

.1.3.6.1.4.1.164.4.2.2.1.1.12

wrWanThrottle

Throttle controls the baud rate of the WAN.
For example if we have a WAN rate of 2M but we want only 1/2 M as
the baud rate we set the Wan Throttle to 512k.

These are the values:
Full (2),
1M (3),
512k (…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.2.2.1.1.13

wrIpTransparentMode

This parameter shows whether the IP Transparent mode is enabled.
When this mode is enabled, all frames (including broadcast and multicast frames)
are forwarded from E1/T1 to LAN and from LAN to E1/T1.

Enumerationr/w

.1.3.6.1.4.1.164.4.2.2.1.1.14

wrIpTransparentGateway

The gateway used for transparent IP.

RFC1155-SMIIpAddressr/w

Enumerated Values:

1	notApplicable
2	close
3	open

Type Constraints:
range: 4

.1.3.6.1.4.1.164.4.2.2.1.1.15

lanrangerLinkProtocolType

This parameter indicates the routing protocol running on this Interface.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	failed
3	passed

.1.3.6.1.4.1.164.4.2.2.1.1.16

lanrangerLinkConnTable

table

.1.3.6.1.4.1.164.4.2.2.2.3 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk lanrangerLinkConnTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::lanrangerLinkConnTable'

A list of Connection entries.  The number of entries is
up to Max entries, according to the LANRANger model.

lanrangerLinkConnEntry row .1.3.6.1.4.1.164.4.2.2.2.3.1

Information about LANRANger Connection.

Indexes

No indexes recorded

Column Syntax OID

lanrangerLinkConnPhysLink

The lanrangerLinkIndex for the physical link with which this logical link is associated.

SNMPv2-SMIInteger32

Enumerated Values:

1	none
2	pap
3	chap

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.2.2.2.3.1.1

lanrangerLinkConnAid

A unique value for each logical link. The maximum number
of logical links is 256, according to the LANRANger model.
The value for each logical link must remain constant at least
from one re-initialization of the ne…

SNMPv2-SMIInteger32

Enumerated Values:

2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.2.2.2.3.1.2

lanrangerLinkConnMacAddr

The MAC address of the device that the logical link is connected to
on the remote LAN.

MacAddress

Type Constraints:
range: 6

.1.3.6.1.4.1.164.4.2.2.2.3.1.3

lanrangerLinkConnStatus

The link connection status.

Enumeration

.1.3.6.1.4.1.164.4.2.2.2.3.1.4

lanrangerLinkConnDeviceType

The type of device that the logical link is connected to on the remote LAN.

Enumeration

.1.3.6.1.4.1.164.4.2.2.2.3.1.5

lanrangerLinkConnDeviceName

The logical name of the device that the logical link is connected to on the remote LAN.

SNMPv2-TCDisplayString

Enumerated Values:

2	no
3	yes

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.4.2.2.2.3.1.6

lanrangerLinkConnDeviceSWVer

SW Version of the device that the logical link is
connected to, on the remote LAN.

SNMPv2-TCDisplayString

Enumerated Values:

1	notApplicable
2	no
3	yes

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.4.2.2.2.3.1.7

lanrangerLinkConnNumLanStation

The number of stations of the remote LAN.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.2.2.2.3.1.8

lanrangerLinkSyncStatus

The Sync link status.

Enumeration

.1.3.6.1.4.1.164.4.2.2.2.3.1.9

lanrangerModemTable

table

.1.3.6.1.4.1.164.4.2.2.3 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk lanrangerModemTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::lanrangerModemTable'

A list of Modem entries.  The number of entries is
up to ifIndex.

lanrangerModemEntry row .1.3.6.1.4.1.164.4.2.2.3.1

LANRANger-specific parameter values for a Modem.

Indexes

No indexes recorded

Column Syntax OID

lanrangerModemLinkIndex

A list of asynchronous ports of the link, according to
ifIndex.
Synchronous ports will not appear in this table. Their
port number will be skipped.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.2.2.3.1.1

lanrangerModemName

The Modem Name identifier for MBE/TRE.
Up to 50 characters.

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.4.2.2.3.1.2

lanrangerModemSettingString

Modem setting String.
Up to 80 characters.

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.4.2.2.3.1.3

lanrangerModemAutobaudingSpeed

Enable or disable autobauding.
When the Autobauding feature is enabled, the MBE/TRE
automatically ranges over various Baud rates, starting
with 115.2 Kbps, until the correct Baud rate of the modem
is detected.

Enumerationr/w

.1.3.6.1.4.1.164.4.2.2.3.1.4

lanrangerModemResetBeforeSetup

Reset the modem before setup is performed.
It is recommended to reset the modem before modem setup
session.

Enumerationr/w

.1.3.6.1.4.1.164.4.2.2.3.1.5

lanrangerModemAnalyzeAnswers

Enable this option if a modem using non-standard answering is used.
When this mode is enabled, the MBE/TRE awaits modem answers
'CONNECT', 'CARRIER', or 'OK', after it transmits a modem command.
Modem answers acknowledg…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	down
3	up

.1.3.6.1.4.1.164.4.2.2.3.1.6

lanrangerModemSpeaker

Toggle the Modem Speaker On or Off .

Enumerationr/w

.1.3.6.1.4.1.164.4.2.2.3.1.7

lanrangerModemDialingNumber

Various command switches listed in Modem Dialing Number Menu
allows selection of tone, pulse-dialing, or various wait states.
P - Set Pulse dialing number .
T - Set Tone dialing number .
W - Wait for dialing tone befor…

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.4.2.2.3.1.8

wrLocalDialBackNumber

This is the number that the Remote Modem will use to call the local
Modem at Dial Back.

Various command switches listed in Modem Dialing Number Menu
allows selection of tone, pulse-dialing, or various wai…

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.4.2.2.3.1.9

wrRingsBeforeAnswer

Determines which ring the modem will wait to answer the
phone on.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.2.2.3.1.10

lanrangerModemDialRetries

The number of dialing retries requested.
Default = 0

Integer32r/w

.1.3.6.1.4.1.164.4.2.2.3.1.11

lanrangerLinkPktSwTable

table

.1.3.6.1.4.1.164.4.2.2.4 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk lanrangerLinkPktSwTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::lanrangerLinkPktSwTable'

A list of X.25/FR modules entries.  The number of entries is
up to ifIndex.

lanrangerLinkPktSwEntry row .1.3.6.1.4.1.164.4.2.2.4.1

LANRANger-specific parameter values for X.25/FR modules.

Indexes

No indexes recorded

Column Syntax OID

lanrangerLinkPktSwIndex

A unique value for each X.25/FR of the link, according to
numbering system of ifIndex. The maximum number of links is
ifIndex. The value for each link must remain constant at
least from one re-initialization of the n…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.2.2.4.1.1

lanrangerLinkPktSwType

Packet Switch Type.

Enumeration

.1.3.6.1.4.1.164.4.2.2.4.1.2

lanrangerLinkPktSwControlSignal

Packet Switch control command.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	untag
3	tag

.1.3.6.1.4.1.164.4.2.2.4.1.3

lanrangerLinkPktSwSpeed

The Pkt Switch port's speed in bits per second.
Range: 1200bps .. 1544000bps

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.2.2.4.1.4

lanrangerLinkPktSwConfigParity

The Pkt Switch Config port's character parity bit.
Applicable only for x25FRConfigChannel. For x25FRChannel
the value notApplicable applies.

Enumerationr/w

.1.3.6.1.4.1.164.4.2.2.4.1.5

lanrangerLinkPktSwConfigStopBit

The Pkt Switch Config port's number of stop bits.
Applicable only for x25FRConfigChannel. For x25FRChannel
the value notApplicable applies.

Enumerationr/w

.1.3.6.1.4.1.164.4.2.2.4.1.6

lanrangerLinkPktSwResetModule

Reset command to Pkt Switch module.
Applicable only for x25FRChannel.
The command will have no effect on x25FRConfigChannel.

Enumerationr/w

.1.3.6.1.4.1.164.4.2.2.4.1.7

wrPPPTable

table

.1.3.6.1.4.1.164.4.2.2.5 · 1 row entry · 16 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk wrPPPTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::wrPPPTable'

This table contains only parameters that do not exist in the PPP
standard MIBS.
The table contains a list of PPP entries.  
The number of entries is up to ifIndex.

wrPPPEntry row .1.3.6.1.4.1.164.4.2.2.5.1

LANRANger-specific parameter values for a PPP.

Indexes

No indexes recorded

Column Syntax OID

wrPPPCompressionHeaderField

This configuration option provides a method to negotiate the
compression of the Data Link Layer Address and Control fields.
This configuration option is sent to inform the peer that the
implementation can receive compre…

Enumerationr/w

.1.3.6.1.4.1.164.4.2.2.5.1.1

wrPPPCompressionProtocolFields

This configuration option provides a method to negotiate the
compression of the PPP Protocol field. This configuration option
is sent to inform the peer that the implementation can receive
such single octet Protocol fie…

Enumerationr/w

Enumerated Values:

1	unknown
2	learned
3	self
4	static

.1.3.6.1.4.1.164.4.2.2.5.1.2

wrPPPSTACCompressionType

The PPP compression control protocol provides a method to negotiate
and utilize compression protocol over PPP encapsulated links.
These are Different types of data compression algorithm for PPP
encapsulated packets.

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.4.2.2.5.1.3

wrPPPAuthProtocol

The type of authentication protocol being used. The left parameter
is the maximum authentication, the right parameter is minimum authentication.

Enumerationr/w

.1.3.6.1.4.1.164.4.2.2.5.1.4

wrPPPSecurityType

Type of unit.

Enumerationr/w

.1.3.6.1.4.1.164.4.2.2.5.1.5

wrPPPUserName

PPP User name.

OctetStringr/w

.1.3.6.1.4.1.164.4.2.2.5.1.6

wrPPPPassword

PPP Password .

OctetStringr/w

.1.3.6.1.4.1.164.4.2.2.5.1.7

wrPPPLinkActiveTime

PPP link active time in seconds
Values range: 2 - 900.
Default value = 2

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.2.2.5.1.8

wrPPPIPCPSubnetMaskNegotiation

This object indicates the ifIndex of the link (LAN port)
through which IPCP Subnet Mask negotiation is allowed.
The distinguished value of zero may be used if no link
is enabled for IPCP Subnet Mask negotiation.
…

IF-MIBInterfaceIndexOrZeror/w

Enumerated Values:

1	active
2	delete

Type Constraints:
range: 0..2147483647

Description:

This textual convention is an extension of the
InterfaceIndex convention. The latter defines a greater
than zero value used to identify an interface or interface
sub-layer in the managed system. This extension permits…

.1.3.6.1.4.1.164.4.2.2.5.1.9

wrPPPLinkControlProtocolStatus

PPP Link Control Protocol(LCP) Status

Enumeration

.1.3.6.1.4.1.164.4.2.2.5.1.10

wrPPPAuthenticationStatus

PPP Authentication status.

Enumeration

.1.3.6.1.4.1.164.4.2.2.5.1.11

wrPPPIpcpStatus

IPCP (IP Control Protocol) status.

Enumeration

.1.3.6.1.4.1.164.4.2.2.5.1.12

wrPPPAssignedIPAddress

IP Address assigned by PPP.

RFC1155-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.164.4.2.2.5.1.13

wrPPPActualAuthProtocol

The Actual type of Authentication Protocol that is used.

Enumeration

.1.3.6.1.4.1.164.4.2.2.5.1.14

wrPPPIpTranslationMode

This object enables the IP Translation Mode.

Enumerationr/w

.1.3.6.1.4.1.164.4.2.2.5.1.15

wrPPPTranslatedIpAddr

This object represents the Translated IP Address.
It is relevant only when IP Translation Mode is 'enable'.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.4.2.2.5.1.16

wrMLPPPTable

table

.1.3.6.1.4.1.164.4.2.2.6 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk wrMLPPPTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::wrMLPPPTable'

This table contains a list of ML-PPP entries.

wrMLPPPEntry row .1.3.6.1.4.1.164.4.2.2.6.1

Specific parameter values for a ML-PPP.

Indexes

No indexes recorded

Column Syntax OID

wrMLPPPEpDiscriminatorEnable

Indicates whether the Endpoint Discriminator Option is enabled.

The Endpoint Discriminator Option represents identification of the
system transmitting the packet. This option advises a system that
th…

Enumerationr/w

.1.3.6.1.4.1.164.4.2.2.6.1.1

wrMLPPPReorderingEnable

Indicates whether packets reordering option is enabled.
yes - packets received from MLPPP not in order are
reordered, according to sequence number,
before being transmitted to egress port.
no - received p…

Enumerationr/w

.1.3.6.1.4.1.164.4.2.2.6.1.2

wrMLPPPTxQueueSize

Indicates the number of frames in the Tx Queue.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	ok
2	okSingleBrg
3	okMultiBrg
4	connctFault
5	rxFault
6	txFault
7	channelLoopback
8	rxClockFault
9	t1Alarm

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.2.2.6.1.3

pPPoETable

table

.1.3.6.1.4.1.164.4.2.2.7.1 · 1 row entry · 19 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pPPoETable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pPPoETable'

The PPPoE (Point-to-Point Protocol over Ethernet) Table.

pPPoEEntry row .1.3.6.1.4.1.164.4.2.2.7.1.1

An entry in the PPPoE Table.

Indexes

No indexes recorded

Column Syntax OID

pPPoECnfgIdx

This object represents the first index of the table.
It can serve for Configuration index or other.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.2.2.7.1.1.1

pPPoEID

This object represents the PPPoE unique Identifier.

SNMPv2-SMIUnsigned32

Enumerated Values:

1	enable
2	disable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.2.2.7.1.1.2

pPPoERowStatus

This object enables the user to create/delete entries in this table.

SNMPv2-TCRowStatusr/w

Enumerated Values:

1	not-inserted
2	active
3	not-active
4	disable

Description:

.1.3.6.1.4.1.164.4.2.2.7.1.1.3

pPPoEACName

This object represents the Name of the Access Concentrator,
with which the PPPoE session should be established.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.4.2.2.7.1.1.4

pPPoEServiceName

This object represents the Name of a specific Service
that will be requested on this PPPoE session.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Enumerated Values:

1	enable
2	disable

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.4.2.2.7.1.1.5

pPPoEEntityPointer

This parameter represents the entity (interface/port etc)
that is connected to this PPPoE.

The value of this parameter is a pointer to an existing row of a table,
where the entity connected to this PP…

SNMPv2-TCRowPointerr/w

Enumerated Values:

1	none
2	lowSpeed
3	highSpeed

Description:

Represents a pointer to a conceptual row. The value is the
name of the instance of the first accessible columnar object
in the conceptual row.

For example, ifIndex.3 would point to the 3rd row in the
ifTable…

.1.3.6.1.4.1.164.4.2.2.7.1.1.6

pPPoESessionStatus

This object represents the Status of the PPPoE session.

Enumeration

Enumerated Values:

1	destinationOnly
2	sourceAndDestination

.1.3.6.1.4.1.164.4.2.2.7.1.1.7

pPPoESessionID

This object represents PPPoE Session ID.

SNMPv2-SMIUnsigned32

Enumerated Values:

1	unknown
2	none
3	x21Old
4	x21
5	v35Old
6	v35
7	rs530Old
8	rs530
9	rs232Old
10	rs232
11	spsV35
12	spsRS530
13	spsRS232
14	spsX21
15	isdn

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.2.2.7.1.1.8

pPPoERemoteMacAddr

This object represents the MAC Address of the Access Concentrator,
with which the PPPoE session is established.

MacAddress

Constraints:
range: 1-17

.1.3.6.1.4.1.164.4.2.2.7.1.1.9

pPPoENoOfUsages

This object represents the number of times this PPPoE is used.

SNMPv2-SMIUnsigned32

Constraints:
range: 1-6

.1.3.6.1.4.1.164.4.2.2.7.1.1.10

pPPoESchedRestartMode

This object represents Scheduled Restart Mode.

Enumerationr/w

Constraints:
range: 1-6

.1.3.6.1.4.1.164.4.2.2.7.1.1.11

pPPoESchedRestartTime

This object represents Scheduled Restart Time.
It is relevant only when Scheduled Restart Mode is 'enable'.

SNMPv2-TCDisplayStringr/w

Enumerated Values:

1	enable
2	disable

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.4.2.2.7.1.1.12

pPPoESchedRestartRandomRange

This object represents Scheduled Restart Random Range (in seconds).
It is relevant only when Scheduled Restart Mode is 'enable'.

A scheduled restart Random VALUE (number of seconds) is selected
within thi…

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.2.2.7.1.1.13

pPPoESchedRestartActualTime

This object represents Scheduled Restart Actual Time.
It is relevant only when Scheduled Restart Mode is 'enable'.
For calculation of this time - see pPPoESchedRestartRandomRange.

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.4.2.2.7.1.1.14

pPPoEInitDelayRandomRange

This object represents the Initialization Delay Random Range (in seconds).
An initialization DELAY (number of seconds) is selected within this Random Range.

This DELAY is used to delay the initialization …

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.2.2.7.1.1.15

pPPoEInitActualDelay

This object represents Initialization Delay (in seconds),
as selected within Initialization Delay Random Range (pPPoEInitDelayRandomRange).

SNMPv2-SMIUnsigned32

Enumerated Values:

vot

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.2.2.7.1.1.16

pPPoEVlanTagging

This object represents the VLAN Tagging.

Enumerationr/w

.1.3.6.1.4.1.164.4.2.2.7.1.1.17

pPPoEVlanId

This object represents the VLAN ID.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.2.2.7.1.1.18

pPPoEVlanPriority

This object represents the VLAN Priority.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.4.2.2.7.1.1.19

lanrangerStationTable

table

.1.3.6.1.4.1.164.4.2.3.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk lanrangerStationTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::lanrangerStationTable'

A table that contains information about the stations 
on the remote LAN(s).
A remote LANRANger contains a list of stations on its 
LAN, while a main LANRANger contains a list of 
stations at all the remote sites it is connected to.

lanrangerStationEntry row .1.3.6.1.4.1.164.4.2.3.1.1

Information about a specific station, that the LANRANger
lists as being on a remote LAN.

Indexes

trimBackUpDay

Column	Syntax	OID
lanrangerStationPhysLink The number of the physical link that is connected to the remote LAN on which the station with the associated instance of lanrangerStationAddress is located. The number is the same as the ifIndex of the link. The valu…	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.2.3.1.1.1`
lanrangerStationLogLink The number of the logical link that is connected to the remote LAN on which the station with the associated instance of lanrangerStationAddress is located. The value will be zero on a remote LANRANger. noLogicLink = …	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.2.3.1.1.2`
lanrangerStationAddress The unicast MAC address of a station that the LANRANger lists as being on a remote LAN.	MacAddress Type Constraints: `range: 6`	`.1.3.6.1.4.1.164.4.2.3.1.1.3`
lanrangerStationStatus The status of this entry. The meanings of the values are: unknown(1) : learned(2) : the value of the corresponding instance of lanrangerStationAddress was learned and is being used. …	Enumeration	`.1.3.6.1.4.1.164.4.2.3.1.1.4`
lanrangerStationSpoofingStatus The spoofing status of this entry.	Enumeration	`.1.3.6.1.4.1.164.4.2.3.1.1.5`

lanrangerPermanentTable

table

.1.3.6.1.4.1.164.4.2.3.4.3 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk lanrangerPermanentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::lanrangerPermanentTable'

A table containing address information
configured into the LANRANger by (local or network)
management, specifying addresses on a remote LAN. 
This table objects can be set only on a Remote LANRANger.

lanrangerPermanentEntry row .1.3.6.1.4.1.164.4.2.3.4.3.1

Address information configured into the remote LANRANger
by (local or network) management specifying addresses
on a remote LAN.

Indexes

No indexes recorded

Column Syntax OID

lanrangerPermanentIfIndex

The number of the physical link that is connected to
the remote LAN, on which the station with the
associated instance of lanrangerStationAddress is
located.
The number is the same as the ifIndex of the link.
This da…

SNMPv2-SMIInteger32

Enumerated Values:

1	enable
2	disable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.2.3.4.3.1.1

lanrangerPermanentLogLink

The number of the logical link that is connected to the
remote LAN, on which the station with the associated
instance of lanrangerPermanentAddress is located.
The value will be noLogicLink on a remote LANRANger.
This d…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.2.3.4.3.1.2

lanrangerPermanentAddress

The MAC address entered by management to this entry.
Only the remote LANRANger will accept Set for this object !
----------------

MacAddress

Type Constraints:
range: 6

.1.3.6.1.4.1.164.4.2.3.4.3.1.3

lanrangerPermanentOperation

This object indicates the status of this entry.
active(1) - this entry is currently in use
and will remain so even after the next
reset of the LANRANger.
delete(2) - writing this value to the obj…

Enumerationr/w

.1.3.6.1.4.1.164.4.2.3.4.3.1.4

lanrangerSpoofingTable

table

.1.3.6.1.4.1.164.4.2.3.6.3 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk lanrangerSpoofingTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::lanrangerSpoofingTable'

A list of Spoofing entries. The number of entries is 
up to the current number of entries, according to the 
LANRANger model. 
Only the LOCAL LANRANger will show this table !
         ---------------

lanrangerSpoofingEntry row .1.3.6.1.4.1.164.4.2.3.6.3.1

Spoofing parameters per entry of the Spoofing table.

Indexes

No indexes recorded

Column	Syntax	OID
lanrangerSpoofingGroup The spoofing group. Only the LOCAL Lanranger will show this table !	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.2.3.6.3.1.1`
lanrangerSpoofingMacAddress MAC Address of the Remote Lanrangers. Only the LOCAL Lanranger will show this table !	MacAddress Type Constraints: `range: 6`	`.1.3.6.1.4.1.164.4.2.3.6.3.1.2`
lanrangerSpoofingAging Aging time defined for a whole group, in minutes. Only the LOCAL Lanranger will show this table !	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.2.3.6.3.1.3`
lanrangerSpoofingTimeLeft Time until aging expires, per station, in minutes. Only the LOCAL Lanranger will show this table !	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.2.3.6.3.1.4`

trimIfTable

table

.1.3.6.1.4.1.164.4.3.1.1 · 1 row entry · 18 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk trimIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::trimIfTable'

RAD-specific interface table.

trimIfEntry row .1.3.6.1.4.1.164.4.3.1.1.1

An entry in table trimIfTable.

Indexes

mlbPortIndex

Column Syntax OID

trimIfIndex

Index to the Trimbridge Interface Table. The interface defined by a
particular value of this index is the same interface as
identified by the same value of ifIndex (MIB II).

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.3.1.1.1.1

trimIfBoardNum

Reserved for possible future use. Not currently applicable to Trimbridge.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.3.1.1.1.2

trimIfNetAddress

The IP address of the interface defined by the particular value of
trimIfIndex.

RFC1155-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.164.4.3.1.1.1.3

trimIfStatus

The current status of the interface. Some of these status values are not applicable to Trimbridge.

Enumeration

Enumerated Values:

1	burnedIn
2	locallyAdministered

.1.3.6.1.4.1.164.4.3.1.1.1.4

trimIfClockType

trimIfClockType defines the type of clock each interface
uses: internal or external.

Enumerationr/w

.1.3.6.1.4.1.164.4.3.1.1.1.5

trimIfBaudRate

Defines the baud rate in use by the interface. The valid
rates are determined by the type of the media for which this
baud rate is defined.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.3.1.1.1.6

trimIfCost

This object is inapplicable to Trimbridge.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.3.1.1.1.7

trimIfCompression

Defines whether data compression is enabled or disabled for the
interface.

Enumerationr/w

Enumerated Values:

1	disable
2	enable

.1.3.6.1.4.1.164.4.3.1.1.1.8

trimIfCompressionStatus

Defines the status of the compression component:
not-inserted - compression component is not in the device
active - compression is enabled and operates correctly
not-active - compression is enables but does not operate…

Enumeration

Enumerated Values:

1	inactive
2	active

.1.3.6.1.4.1.164.4.3.1.1.1.9

trimIfCompressionRate

Percentage of compression. This variable applies only
if trimCompressionStatus is active.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.3.1.1.1.10

trimIfLATCompression

Enable/Disable the LAT Compression.

Enumerationr/w

Enumerated Values:

1	disable
2	enable

.1.3.6.1.4.1.164.4.3.1.1.1.11

trimIfCompressionType

This parameter indicates the type of compression option available in
the device.
`None(1) - indicates that there is no compression option in the device
lowSpeed(2) - indicates a compression option whic…

Enumeration

Enumerated Values:

1	llcCsmacd
3	llcTokenRing
6	sdlc
10	qllcX25

.1.3.6.1.4.1.164.4.3.1.1.1.12

trimIfFilterMode

This parameter indicates the type of filtering in the device.

Enumerationr/w

.1.3.6.1.4.1.164.4.3.1.1.1.13

trimIfConType

This parameter indicates the connector type of an interface.

Enumeration

Constraints:
range: 2-2

.1.3.6.1.4.1.164.4.3.1.1.1.14

trimIfRemAddress

OctetStringr/w

Constraints:
range: 3-3

.1.3.6.1.4.1.164.4.3.1.1.1.15

trimIfLocSubAddress

Space is not valid. If the string includes a space,
the whole entry is considered not valid.

OctetStringr/w

.1.3.6.1.4.1.164.4.3.1.1.1.16

trimIfRemSubAddress

Space is not valid. If the string includes a space,
the whole entry is considered not valid.

OctetStringr/w

.1.3.6.1.4.1.164.4.3.1.1.1.17

trimIfCLIVerification

Enables/Disables verification of Control Line Identification (CLI)

Enumerationr/w

.1.3.6.1.4.1.164.4.3.1.1.1.18

trimIfThresholdRepTable

table

.1.3.6.1.4.1.164.4.3.1.3.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk trimIfThresholdRepTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::trimIfThresholdRepTable'

.....

trimIfThresholdRepEntry row .1.3.6.1.4.1.164.4.3.1.3.1.1

An entry in table trimIfThresholdRepTable.

Indexes

No indexes recorded

Column	Syntax	OID
trimIfThreRepId The Interface number serves as an index to the Threshold Reoprt Table.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.3.1.3.1.1.1`
trimIfThreRepCounterId The Counter ID serves as an index to the Threshold Reoprt Table, and identify the counter for which to pot the threshold.	Enumeration	`.1.3.6.1.4.1.164.4.3.1.3.1.1.2`
trimThresholdValue The Threshold value , this is the maximum rate of counter increments before the element issue trap.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.3.1.3.1.1.3`
trimIfThreRepSampleRate The network object will sample the counter atthis interval. When this parameter is set to 0, the treshold comparison is disable.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.3.1.3.1.1.4`
trimIfThreRepTrapRate The network object will issue a trap according to this interval. Note that the trape interval nust be equal or larger then trimIfThreRepSampleRate.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.3.1.3.1.1.5`

trimBackUpScheduleTable

table

.1.3.6.1.4.1.164.4.3.2.10 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk trimBackUpScheduleTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::trimBackUpScheduleTable'

This is a table that contains the reroute shedule for the backup link.  The index 
is the day of the week, starting with 1 for Sunday, ending with 7 for 
Saturday.

trimBackUpEntry row .1.3.6.1.4.1.164.4.3.2.10.1

An entry in table trimBackUpScheduleTable.

Indexes

No indexes recorded

Column	Syntax	OID
trimBackUpDay The day of the week for which the entry applies. The days are numbered from 1 to 7, representing Monday through Sunday.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.3.2.10.1.1`
trimBackUpFromTo This is the time during which backup should be disabled, expressed as xx:xx-yy:yy, where x's reflect the time from and y's reflect the time to. The first two digits, in x and in y, are the hour and the second two di…	SNMPv2-TCDisplayStringr/w Type Constraints: `range: 0..255` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.164.4.3.2.10.1.2`

trimTRIfTable

table

.1.3.6.1.4.1.164.4.3.3.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk trimTRIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::trimTRIfTable'

This table defines configuration parameters for Token Ring interfaces in the Trimbridge-16.

trimTRIfEntry row .1.3.6.1.4.1.164.4.3.3.1.1

An entry in table trimTRIfTable.

Indexes

No indexes recorded

Column	Syntax	OID
trimTRIfIndex Index to the Token Ring Interface Table. The interface defined by a particular value of this index is the same interface as identified by the same value of ifIndex (MIBII).	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.4.3.3.1.1.1`
trimTREarlyTokenRelease This parameter controls the early token release. This paramenter is applicable only to 16 Mbps rings.	Enumerationr/w	`.1.3.6.1.4.1.164.4.3.3.1.1.2`
trimTRLocalAdminAddress A locally administered MAC Address of this interface.	MacAddressr/w Type Constraints: `range: 6`	`.1.3.6.1.4.1.164.4.3.3.1.1.3`
trimTRLocalAdminAddressStatus This parameter controls whether the bridge uses the locally administered MAC Address defined for this interface, when enable(1), or not , when disable(2).	Enumerationr/w	`.1.3.6.1.4.1.164.4.3.3.1.1.4`

febFtbTranslIfTable

table

.1.3.6.1.4.1.164.4.4.1.1 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk febFtbTranslIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::febFtbTranslIfTable'

The translation table defines which type of translation is required for each device interface. This is
particularly important for WAN links, as the translating device does not have a knowledge of the
target LAN type.

febFtbTranslIfEntry row .1.3.6.1.4.1.164.4.4.1.1.1

Entry in the translation table.

Indexes

No indexes recorded

Column Syntax OID

febFtbTranslIfIndex

Index to the Translation Table. The interface defined by a particular value of this index is the
same interface as identified by the same value of ifIndex (MIBII).

SNMPv2-SMIInteger32

Enumerated Values:

1	sideA
2	sideB

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.4.1.1.1.1

febFtbTunnelProtocol

IEEE 802.1h standard defines the tunneling for Appletalk I. This parameter enables the user
to specify Ethertype of an additional protocol to tunnel (e.g. IPX). For IPX, Enter 8137 to
translate Token Ring SNAP frames to…

OctetStringr/w

.1.3.6.1.4.1.164.4.4.1.1.1.2

febFtbTranslIPXRawEthernet

This variable defines the translation mode for IPX frames in standrad Token Ring format. It is
applicable to Ethernet interfaces (i.e. febFtbTranslSwitch variable has value Ethernet (2). ).
ethernetRaw8023: translate…

Enumerationr/w

Enumerated Values:

1	disable
2	enable
3	underCreation
4	stop
5	start
10	invalid

.1.3.6.1.4.1.164.4.4.1.1.1.3

febFtbLanTable

table

.1.3.6.1.4.1.164.4.4.2.1 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk febFtbLanTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::febFtbLanTable'

febFtbLanTabEntry row .1.3.6.1.4.1.164.4.4.2.1.1

Entry in the LanTab table.

Indexes

No indexes recorded

Column	Syntax	OID
febFtbLanTabIfIndex This variable defines the related interface	SNMPv2-SMIInteger32 Constraints: `range: 2-2`	`.1.3.6.1.4.1.164.4.4.2.1.1.1`
febFtbLanTabEntNumber This variable defines the number of entries in the LAN table reletaed to the specific interface	SNMPv2-SMIInteger32 Constraints: `range: 3-3`	`.1.3.6.1.4.1.164.4.4.2.1.1.2`

mlbAddressTable

table

.1.3.6.1.4.1.164.4.5.2.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mlbAddressTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mlbAddressTable'

A table that contains information about the MLB ports address .

mlbAddressEntry row .1.3.6.1.4.1.164.4.5.2.1.1

Information about a specific port that the MLB lists define.

Indexes

No indexes recorded

Column Syntax OID

mlbPortIndex

A unique value for each port, equal to the value of ifIndex for the port.
The maximum number of ports for mlb is 2 .

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.4.5.2.1.1.1

mlbBurnAddress

This is the burned-in MacAddress on the LANRANger.

MacAddress

Type Constraints:
range: 6

.1.3.6.1.4.1.164.4.5.2.1.1.2

mlbLocAddress

This is a locally administered address. If a zero value appears, the network administrator
did not set a locally administered address.

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.4.5.2.1.1.3

mlbActiveAddress

The MAC address that is in use on the LANRANger.
The address selected will appear in ifPhysAddress.

Enumerationr/w

Enumerated Values:

1	primary
2	secondary

.1.3.6.1.4.1.164.4.5.2.1.1.4

nvaAgentTable

table

.1.3.6.1.4.1.164.5.1.3.3 · 1 row entry · 14 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk nvaAgentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::nvaAgentTable'

nvaAgentEntry row .1.3.6.1.4.1.164.5.1.3.3.1

An entry in table nvaAgentTable.

Indexes

No indexes recorded

Column Syntax OID

nvaAgIndex

Agent number .
Range (1 - nvaAgentsNumber)

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.3.3.1.1

nvaAgAdminStatus

The admin. status of NV AGENT. Value of 'disable'
will prevent the NetView agent from trying to
connect to the NetView management system

Enumerationr/w

.1.3.6.1.4.1.164.5.1.3.3.1.3

nvaAgOperState

Current Operation state of the NetView agent. Active
state means that the NetView agent is in session
with the NetView management system

Enumeration

.1.3.6.1.4.1.164.5.1.3.3.1.4

nvaAgFilter

Alert filter bit mask. Each bit corresponds to a specific alert
sent by the NetView agent.

OctetString

.1.3.6.1.4.1.164.5.1.3.3.1.5

nvaAgAllowRunCmd

Defines whether the NetView agent is allowed to handle
operational commands, received by the RUNCMD facility

Enumerationr/w

.1.3.6.1.4.1.164.5.1.3.3.1.6

nvaAgAccessType

Defines the method in which the agent tries to
connect to the NetView management system(the SNA host)

Enumerationr/w

Enumerated Values:

1	sideA
2	sideB

.1.3.6.1.4.1.164.5.1.3.3.1.7

nvaAgIfIndex

The port number of the interface in which the
NetView agent connects to the SNA host

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.3.3.1.8

nvaAgXidBlockId

The BLOCKID part of the XID information which the NetView agent
should use to connect to the NetView management system
(The SNA host)

OctetStringr/w

Enumerated Values:

1	disable
2	enable

.1.3.6.1.4.1.164.5.1.3.3.1.9

nvaAgXidBlockNum

The BLOCKNUM part of the XID information which the NetView agent
should use to connect to the NetView management system
(The SNA host)

OctetStringr/w

Enumerated Values:

1	sideA
2	sideB

.1.3.6.1.4.1.164.5.1.3.3.1.10

nvaAgSSap

Local SAP, used for the NetView session - for LLC
access type session only.

Sapr/w

.1.3.6.1.4.1.164.5.1.3.3.1.11

nvaAgDSap

Remote(host) Sap used by the NetView agent for the
SNA host connection - for LLC access session type
only.

Sapr/w

Enumerated Values:

1	half
2	full

.1.3.6.1.4.1.164.5.1.3.3.1.12

nvaAgRemMacAddr

Remote(host) MAC address used by the NetView agent
for the SNA host connection - for LLC access session
type only.

MacAddressr/w

Constraints:
range: 2-2

.1.3.6.1.4.1.164.5.1.3.3.1.13

nvaAgSdlcAddr

SDLC address used by the NetView agent for the SNA
host connection - for SDLC access session type only.

SdlcAddrr/w

Constraints:
range: 3-3

.1.3.6.1.4.1.164.5.1.3.3.1.14

nvaAgResourceName

A 4 character name that is appended to the resource
name in the NetView alerts sent by the NetView agent

SNMPv2-TCDisplayStringr/w

Enumerated Values:

1	disable
2	enable

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.5.1.3.3.1.15

nvaAgentStatTable

table

.1.3.6.1.4.1.164.5.1.3.4 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk nvaAgentStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::nvaAgentStatTable'

nvaAgentStatEntry row .1.3.6.1.4.1.164.5.1.3.4.1

An entry in table nvaAgentStatTable.

Indexes

No indexes recorded

Column Syntax OID

nvaAgStatIndex

Agent number .
Range (1 - nvaAgentsNumber)

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.3.4.1.1

nvaAgStatTime

Time since last reset of the NV agent statistics.
Setting to a value of 0 will clear all Agents'
statistics.

RFC1155-SMITimeTicksr/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.1.3.4.1.2

nvaAgActPu

Number of session initiation (ACTPU) requests received from
the SNA host

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.1.3.4.1.3

nvaAgDactPu

Number of session disconnection (DACTPU) requests received
from the SNA host

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.1.3.4.1.4

nvaAgRpNmvt

Number of NMVTs received from the SNA host, and responded
with a positive response.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.1.3.4.1.5

nvaAgRnNmvt

Number of NMVTs received from the SNA host, and
respond with a negative response.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.1.3.4.1.6

nvaAgSpNmvt

Number of NMVTs (of any type) sent to the SNA host.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.1.3.4.1.7

nvaAgSAlerts

Number of alert NMVTs sent by the NetView agent.

SNMPv2-SMICounter32

Enumerated Values:

1	sideA
2	sideB

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.1.3.4.1.9

nvaAgRRunCmd

Number of RUNCMD (execute-command NMVTs) received by the
NetView agent.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.1.3.4.1.10

nvaAgSRunCmd

Number of RUNCMD replies sent to the NetView host.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.1.3.4.1.11

nvaAgSPdstat

Number of PDSTAT NMVTs sent by the NetView agent.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.1.3.4.1.12

snaSessTable

table

.1.3.6.1.4.1.164.5.1.5.3 · 1 row entry · 18 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk snaSessTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::snaSessTable'

Holding SNA session's parameters for each side of a
specific session, indexed by session_id

snaSessEntry row .1.3.6.1.4.1.164.5.1.5.3.1

An entry in table snaSessTable.

Indexes

No indexes recorded

Column Syntax OID

sessIfIndex

Interface used by this SNA session

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.5.3.1.1

sessId

The unique identifier of the converted SNA session id

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.5.3.1.2

sessSide

The SNA session side. Each session handled by SNAR/device,
creates 2 SNA sessions, hereafter called 'side A' and 'side B'
Configuration parameters, and Statistics are defined for each
side separately.

Enumeration

.1.3.6.1.4.1.164.5.1.5.3.1.3

sessDev

The device number, used in devices setup. N/A to SNAR.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.5.3.1.4

sessAdminStatus

Admin. status of this session, as requested by the manager.
10 - Session is invalid, and not handled by SNAR
devices.
1 - Session is disabled. SNAR/Device will not try to start
this session.
2- Session is enable…

Enumerationr/w

.1.3.6.1.4.1.164.5.1.5.3.1.5

sessOperState

Current operating state.
See Manual reference for more information.

Enumeration

.1.3.6.1.4.1.164.5.1.5.3.1.6

sessAccessType

The access type used by this side of the converted
session.

Enumerationr/w

Enumerated Values:

1	sideA
2	sideB

.1.3.6.1.4.1.164.5.1.5.3.1.7

sessSXidBlockId

The BLOCKID part of the XID information sent by this side for the
SNA session initiation

OctetStringr/w

Enumerated Values:

1	disable
2	enable

.1.3.6.1.4.1.164.5.1.5.3.1.8

sessSXidBlockNum

The BLOCKNUM part of the XID information sent by this side for the
SNA session initiation

OctetStringr/w

Enumerated Values:

1	disable
2	enable

.1.3.6.1.4.1.164.5.1.5.3.1.9

sessSSap

The Local SAP used by SNAR for this session's side (LLC
sessions only)

Sapr/w

Enumerated Values:

1	disable
2	enable

.1.3.6.1.4.1.164.5.1.5.3.1.10

sessDSap

The remote SAP used by SNAR for this session's side
(LLC sessions only)

Sapr/w

.1.3.6.1.4.1.164.5.1.5.3.1.11

sessRemMacAddr

The remote MAC address used by this session's side
(LLC sessions only)

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.5.1.5.3.1.12

sessSdlcAddr

The SDLC address used by this session's side
(SDLC sessions only, both primary and secondary)

SdlcAddrr/w

.1.3.6.1.4.1.164.5.1.5.3.1.13

sessGroupPoll

The address of the group poll in which this session's side
participates (SLDC secondary only).
A value of 0 indicates that it doesn't participate
in any group. Only one group is supported for each
SDLC line (same port)

SdlcAddrr/w

.1.3.6.1.4.1.164.5.1.5.3.1.14

sessRole

The type of SDLC session for this side.

Enumerationr/w

.1.3.6.1.4.1.164.5.1.5.3.1.15

sessIpEncapsulated

Specified whether this session data is encapsulated within
UDP/IP

Enumerationr/w

.1.3.6.1.4.1.164.5.1.5.3.1.16

sessDestIpAddr

The destination IP address (IP encapsulated sessions only).

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.5.1.5.3.1.17

sessRemX25Addr

The remote X25 address (QLLC only) .

OctetStringr/w

.1.3.6.1.4.1.164.5.1.5.3.1.18

snaSessTuneTable

table

.1.3.6.1.4.1.164.5.1.5.4 · 1 row entry · 16 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk snaSessTuneTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::snaSessTuneTable'

Holding SNA session parameters for each side of a
specific session, indexed by session_id

snaSessTuneEntry row .1.3.6.1.4.1.164.5.1.5.4.1

An entry in table snaSessTuneTable.

Indexes

sdlcIfIndex

Column Syntax OID

sessTuneIfIndex

The SNA session side.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.5.4.1.1

sessTuneId

The unique identifier of the converted SNA session.

SNMPv2-SMIInteger32

Enumerated Values:

1	nrz
2	nrzi

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.5.4.1.2

sessTuneSide

The SNA session's side.

Enumeration

Enumerated Values:

1	half
2	full

.1.3.6.1.4.1.164.5.1.5.4.1.3

sessBufferSize

The max. buffer size of remote device (All sessions).

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	external
2	internal

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.5.4.1.4

sessSegmentation

Specifies whether the SNAR should perform
segmentation when incoming frame on one side is
longer then the sessSideBufferSize of the other size

1 - disable - don't perform segmentation
2 - enable - perform…

Enumerationr/w

.1.3.6.1.4.1.164.5.1.5.4.1.5

sessFirstSide

Specifies which side of the two SNA sides (side_a or side_b)
should be started first (SNAR only, N/A to devices)

Enumeration

.1.3.6.1.4.1.164.5.1.5.4.1.6

sessWindow

The max window size (1 .. 127) for this session's side.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	constatnt
2	controled

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.5.4.1.7

sessDuplex

Specifies the type of SDLC device on the other end
of the SDLC line. FULL- means a device capable of
transmit and receive data simultaneously.

Enumerationr/w

.1.3.6.1.4.1.164.5.1.5.4.1.8

sessRXidBlockId

The BLOCKID part of the XID information expected to be received
on this side of the SNA session

OctetStringr/w

.1.3.6.1.4.1.164.5.1.5.4.1.9

sessRXidBlockNum

The BLOCKNUM part of the XID information expected to be received
on this side of the SNA session

OctetStringr/w

.1.3.6.1.4.1.164.5.1.5.4.1.10

sessCheckXid

Specified whether the received XID information should
be checked and compared to the value of sessRXid:
1 - disable: don't check
2 - enable : check

Enumerationr/w

.1.3.6.1.4.1.164.5.1.5.4.1.11

sessT1

The T1 timer (in 100 msec) for this session's side.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.5.4.1.12

sessTi

The Ti timer (in sec) for this session

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.5.4.1.13

sessT2

The T2 timer (in 100 msec) for this session

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.5.4.1.14

sessN2

The N2 value for this session's side

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.5.4.1.15

sessUdpPort

The UDP port used by SNAR (IP encapsulated
sessions only)

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.5.4.1.16

snaSessStatTable

table

.1.3.6.1.4.1.164.5.1.5.5 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk snaSessStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::snaSessStatTable'

Holding SNA session parameters for each side of a
	   specific session, indexed by session_id

snaSessStatEntry row .1.3.6.1.4.1.164.5.1.5.5.1

An entry in table snaSessStatTable.

Indexes

No indexes recorded

Column Syntax OID

sessStatIfIndex

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.5.5.1.1

sessStatId

The unique identifier of the converted SNA session.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.5.5.1.2

sessStatSide

The SNA session's side.

Enumeration

.1.3.6.1.4.1.164.5.1.5.5.1.3

sessStatTime

Time since last reset of this session statistics.
Setting to a value of 0 will clear all session
statistics.

RFC1155-SMITimeTicksr/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.1.5.5.1.4

sessSPius

The number of PIUs sent by this session's side

SNMPv2-SMICounter32

Enumerated Values:

1	no-op
2	open
3	reset
4	close

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.1.5.5.1.5

sessSBytes

The number of bytes sent by this session's side.

SNMPv2-SMICounter32

Enumerated Values:

1	unknown
2	oneMegabit
3	fourMegabit
4	sixteenMegabit

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.1.5.5.1.6

sessRPius

The number of PIUs received by this session

SNMPv2-SMICounter32

Enumerated Values:

1	true
2	false

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.1.5.5.1.7

sessRBytes

The number of bytes received by this session's side.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.1.5.5.1.8

sessSessFailure

The number of session failures occurs to this
session's side.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.1.5.5.1.9

sessXidDenieds

The number of XID denied by this session's side

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.1.5.5.1.10

snaSessQllcTable

table

.1.3.6.1.4.1.164.5.1.5.7 · 1 row entry · 14 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk snaSessQllcTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::snaSessQllcTable'

Holding SNA session parameters for each side of a
	   specific session, indexed by session_id

snaSessQllcEntry row .1.3.6.1.4.1.164.5.1.5.7.1

An entry in table snaSessQllcTable.

Indexes

No indexes recorded

Column Syntax OID

sessQllcIfIndex

SNMPv2-SMIInteger32

Enumerated Values:

1	no-op
2	open
3	reset
4	close

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.5.7.1.1

sessQllcId

The unique identifier of the converted SNA session.

SNMPv2-SMIInteger32

Enumerated Values:

1	true
2	false

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.5.7.1.2

sessQllcSide

The SNA session's side.

Enumeration

.1.3.6.1.4.1.164.5.1.5.7.1.3

sessInCalls

N/Allowed to accept call indicators (QLLC only)
1- disable: don't allow to accept call indications
2- enable: Allow to accept call indications

Enumerationr/w

.1.3.6.1.4.1.164.5.1.5.7.1.4

sessOutCalls

N/Allowed to initiate call requests (QLLC only)
1- disable: don't allow to initiate call requests
2- enable: Allow to initiate call requests

Enumerationr/w

.1.3.6.1.4.1.164.5.1.5.7.1.5

sessPVC

PVC being used or not (QLLC only)
1 - disable :not use
2 - enable :use

Enumerationr/w

.1.3.6.1.4.1.164.5.1.5.7.1.6

sessCallReqData

The user's data for call requests (QLLC only).

OctetStringr/w

.1.3.6.1.4.1.164.5.1.5.7.1.7

sessConnReqFacility

The facilities for connection requests (QLLC only).

OctetStringr/w

.1.3.6.1.4.1.164.5.1.5.7.1.8

sessGroupId

The facility group id (QLLC only)

OctetStringr/w

.1.3.6.1.4.1.164.5.1.5.7.1.9

sessDtePswd

The password for local DTE (QLLC only)

OctetStringr/w

.1.3.6.1.4.1.164.5.1.5.7.1.10

sessDteId

The identification for local DTE (QLLC only).

OctetStringr/w

.1.3.6.1.4.1.164.5.1.5.7.1.11

sessMaxInPktSize

The max inbound packet size (QLLC only).

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.5.7.1.12

sessMaxOutPktSize

The max outbound packet size (QLLC only).

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.1.5.7.1.13

sessCallIndReverse

OctetStringr/w

.1.3.6.1.4.1.164.5.1.5.7.1.14

sdlcTable

table

.1.3.6.1.4.1.164.5.2.1.3 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sdlcTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sdlcTable'

sdlcEntry row .1.3.6.1.4.1.164.5.2.1.3.1

An entry in table sdlcTable.

Indexes

No indexes recorded

Column	Syntax	OID
sdlcIfIndex The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object, defined in [4,6], fo…	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.5.2.1.3.1.1`
sdlcNrz	Enumerationr/w	`.1.3.6.1.4.1.164.5.2.1.3.1.2`
sdlcDuplex	Enumerationr/w	`.1.3.6.1.4.1.164.5.2.1.3.1.3`
sdlcClockType	Enumerationr/w	`.1.3.6.1.4.1.164.5.2.1.3.1.4`
sdlcSpeed	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.5.2.1.3.1.5`
sdlcConnectorType	SNMPv2-TCDisplayString Type Constraints: `range: 0..255` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.164.5.2.1.3.1.6`
sdlcRts	Enumeration	`.1.3.6.1.4.1.164.5.2.1.3.1.7`

sdlcStatTable

table

.1.3.6.1.4.1.164.5.2.1.4 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sdlcStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sdlcStatTable'

sdlcStatEntry row .1.3.6.1.4.1.164.5.2.1.4.1

An entry in table sdlcStatTable.

Indexes

No indexes recorded

Column Syntax OID

sdlcStatIfIndex

The value of this object identifies the
interface for which this entry
contains management information. The
value of this object for a particular
interface has the same value as the
ifIndex object, defined in [4,6],
fo…

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.2.1.4.1.1

sdlcTimeSinceReset

The time laps since the last reset statistics.
Setting the object to 0 will reset all line statistics.

RFC1155-SMITimeTicksr/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.2.1.4.1.2

sdlcStatFramesTrans

SNMPv2-SMICounter32

Enumerated Values:

1	unknown
220	gstm1
221	goc3
222	gstm1D
223	goc3D
270	serverE1
271	serverT1
272	serverE1Pw
273	serverT1Pw
280	gigabitEth
281	gigabitEth2
282	eth2
283	gigabitEth8
284	eth8
290	channelizedT3Pw1
300	cesT128
301	cesE128
302	cesT1Pw28
303	cesE1Pw28
310	vmxE1VeDe
311	vmxE1VeDi
312	vmxE1ViDe
313	vmxE1ViDi
314	vmxT1VeDe
315	vmxT1VeDi
316	vmxT1ViDe
317	vmxT1ViDi
318	vc12E1UeNe
319	vc12E1UeNi
320	vc12E1UiNe
321	vc12E1UiNi
322	vc12T1UeNe
323	vc12T1UeNi
324	vc12T1UiNe
325	vc12T1UiNi
326	vca16E1UeNe
327	vca16E1UeNi
328	vca16E1UiNe
329	vca16E1UiNi
330	vca16T1UeNe
331	vca16T1UeNi
332	vca16T1UiNe
333	vca16T1UiNi
334	vca12E1UeNe
335	vca12E1UeNi
336	vca12E1UiNe
337	vca12E1UiNi
338	vca12T1UeNe
339	vca12T1UeNi
340	vca12T1UiNe
341	vca12T1UiNi
342	vmg16E1Ue
343	vmg16E1Ui
344	vmg16T1Ue
345	vmg16T1Ui
346	vmg12E1Ue
347	vmg12E1Ui
348	vmg12T1Ue
349	vmg12T1Ui

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.2.1.4.1.3

sdlcStatBytesTrans

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.2.1.4.1.4

sdlcStatFramesRcv

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.2.1.4.1.5

sdlcStatBytesRcv

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.2.1.4.1.6

sdlcStatFramesAbort

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.2.1.4.1.7

sdlcStatFramesBad

This counter holds the number of all bad frames.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.2.1.4.1.8

sdlcStatFramesCrc

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.5.2.1.4.1.9

cvtDot5Table

table

.1.3.6.1.4.1.164.5.2.2.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk cvtDot5Table

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::cvtDot5Table'

This table contains Token Ring interface
parameters and state variables. One entry
per 802.3 interface.

cvtDot5Entry row .1.3.6.1.4.1.164.5.2.2.1.1

An entry in table cvtDot5Table.

Indexes

No indexes recorded

Column Syntax OID

cvtDot5IfIndex

The value of this object identifies the
802.5 interface for which this entry
contains management information. The
value of this object for a particular
interface has the same value as the
ifIndex object, defined in [4,…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.5.2.2.1.1.1

cvtDot5MacAddr

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.5.2.2.1.1.2

cvtDot5Commands

When this object is set to the value of
open(2), the station should go into the
open state.
When this object is set to the value of
of reset(3), the station should perform reset.
When this object is set to the value
o…

Enumerationr/w

.1.3.6.1.4.1.164.5.2.2.1.1.3

cvtDot5RingSpeed

The ring's bandwidth.

Enumerationr/w

.1.3.6.1.4.1.164.5.2.2.1.1.4

cvtDot5ActMonParticipate

If this object has a value of true(1) then
this interface will participate in the
active monitor selection process. If the
value is false(2) then it will not.
Setting this object might not have an
effect until the next…

Enumerationr/w

Enumerated Values:

1	alarmsBuffer

.1.3.6.1.4.1.164.5.2.2.1.1.5

cvtDot5Functional

The bit mask of all TR functional
addresses for which this interface will
accept frames.

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.5.2.2.1.1.6

cvtDot3Table

table

.1.3.6.1.4.1.164.5.2.3.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk cvtDot3Table

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::cvtDot3Table'

This table contains ETHERNET interface
parameters and state variables, one entry
per 802.3 interface.

cvtDot3Entry row .1.3.6.1.4.1.164.5.2.3.1.1

An entry in table cvtDot3Table.

Indexes

No indexes recorded

Column	Syntax	OID
cvtDot3IfIndex The value of this object identifies the 802.3 interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object, defined in [4,…	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.5.2.3.1.1.1`
cvtDot3MacAddr	MacAddressr/w Type Constraints: `range: 6`	`.1.3.6.1.4.1.164.5.2.3.1.1.2`
cvtDot3Commands When this object is set to the value of open(2), the station should go into the open state. of reset(3), then the station should do a reset. On a reset, all MIB counters should retain their values, if possible. Other …	Enumerationr/w	`.1.3.6.1.4.1.164.5.2.3.1.1.3`
cvtDot3ActMonParticipate If this object has a value of true(1) then this interface will participate in the active monitor selection process. If the value is false(2) then it will not. Setting this object might not have an effect until the next…	Enumerationr/w	`.1.3.6.1.4.1.164.5.2.3.1.1.4`
cvtDot3Functional The bit mask of all Ethernet functional addresses for which this interface will accept frames.	MacAddressr/w Type Constraints: `range: 6`	`.1.3.6.1.4.1.164.5.2.3.1.1.5`

mngTrapIpTable

table

.1.3.6.1.4.1.164.6.2.7 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mngTrapIpTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mngTrapIpTable'

This table indicates  the destination address of the traps.
Internally it will be limited to ten addresses.

mngEntry row .1.3.6.1.4.1.164.6.2.7.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

mngID

This value indicates an index of a specific IP address

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.7.1.1

mngIP

This value indicates the destination address of the traps. IP 0.0.0.0 removes the entry.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.6.2.7.1.2

mngIPMaskdeprecated

This value indicates the mask of the destination addresses of the traps.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.6.2.7.1.3

mngTrapMask

The value of this attribute determines the type of traps the
agent should mask and not send to this NMS. The
value is differently determined for different products. There are
mainly two methods:
- an integer number, …

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	up
2	down

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.7.1.4

mngAlarmTrapMask

The value of this object determines the alarm traps that the
agent should mask (not send to this manager).
The value is an Octet String, where each bit
is assigned to a certain trap.
If the bit = 1, the trap will be…

OctetStringr/w

Enumerated Values:

1	unicast
2	broadcast

.1.3.6.1.4.1.164.6.2.7.1.5

mngSnmpTrapUdpPort

This variable enables to set the UDP port (socket) used for SNMP traps.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.7.1.6

trapTable

table

.1.3.6.1.4.1.164.6.2.11 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk trapTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::trapTable'

This table may include the last few traps generated by the agent, for future retrieval. The table
has a limited capacity. If traps are not retrieved in proper time, they will be
over-written by new traps.
For other devices, it can include generic variables that will be attached to traps
as 'accessible-for-notify'.

trapEntry row .1.3.6.1.4.1.164.6.2.11.1

An entry in trapTable.

Indexes

No indexes recorded

Column Syntax OID

trapID

This object indicates an index of a specific trap.
Can be used also for any trap, while trapVal is used
as 'accessible-for-notify' or trapNumeric is used.

SNMPv2-SMIInteger32

Enumerated Values:

2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.11.1.1

trapVal

This object is the actual ASCII description of the trap.
It can be used also as attached variable of traps, in order
to detail in explicit ASCII text, data of the trap.
In this case, it is used as 'accessible-for-notif…

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.6.2.11.1.2

trapTimeSinceOccurrence

This object indicates the amount of time passed since the occurrence of the event that
triggered this trap.

RFC1155-SMITimeTicks

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.11.1.3

trapNumeric

This object is a numeric general parameter, that can be attached to any trap.
Values can be positive or negative.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.11.1.4

intSwdlTable

table

.1.3.6.1.4.1.164.6.2.12.10 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk intSwdlTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::intSwdlTable'

This parameters table is for 
internal Software down load. It also includes data 
about all files contained in the Object from which 
down-load is performed.

intSwdlEntry row .1.3.6.1.4.1.164.6.2.12.10.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

intSwdlObjIdx

The index of the object from which down-load is performed.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.12.10.1.1

intSwdlFileIdx

The index of the files included in intSwdlObjIdx.
One of these files can be selected to be internally
downloaded.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.12.10.1.2

intSwdlFileName

The name of the file.

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.6.2.12.10.1.3

intSwdlFileSwVer

The software version of the file.

SNMPv2-TCDisplayString

Enumerated Values:

1	other
2	v35
3	rs530
4	x21
5	bnc
6	utp
7	aui
8	rs422
9	crossUtp
10	rj45
11	v24
12	g703
13	termBlock3AndRj45
14	terminalBlock3
15	terminalBlock5
16	terminalBlock7
17	db25
18	db15
19	rj45ethernet
20	termBlock5AndRj45
21	db9
22	g703E1
23	g703E1-LTU
24	sc
25	st
26	stl
27	fc
28	tb5w
29	termBlock6AndRj45
30	ethBnc
31	scsi26
32	eth4381
33	twoBnc
34	scsi50
35	twoMiniBnc
36	sf1
37	terminalBlock4
38	sf2
39	db25Balanced
40	v36
41	block4W
42	iripRj45
43	irEthQRj45
44	iripBnc
45	rs530WA
46	v35WA
47	irEthQBnc
48	v35Db25
49	rj11
50	mtrj
51	lc
52	terminalBlock2
53	irEth10s100
54	scsi68
55	sf3
56	fcLH
57	telco50
58	telco64
59	irEthQN
60	terminalBlock6
61	scLH
62	stLH
63	lcLH
64	sfpIn
65	sfpOut
66	db44
67	db62
68	v24Db9
69	scsi40
70	sf1NineRow
71	sf2NineRow
72	sf3NineRow
73	smartSerial26
74	miniUsb5
75	db26
76	comboUtpSfpIn
77	comboUtpSfpOut
255	none

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.6.2.12.10.1.4

intSwdlSwDate

The software version date of the file.

SNMPv2-TCDisplayString

Enumerated Values:

1	notApplicable
2	nm850
3	nm1310
4	nm1310Laser
5	nm1550Laser
6	nm1470Laser
7	nm1490Laser
8	nm1510Laser
9	nm1530Laser
10	nm1570Laser
11	nm1590Laser
12	nm1610Laser

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.6.2.12.10.1.5

intSwdlSize

The size of the file.

SNMPv2-TCDisplayString

Enumerated Values:

1	notApplicable
2	singleMode
3	multiMode

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.6.2.12.10.1.6

intSwdlCmd

The command to down-load a SW file to an object.
The Agent will change the value of this MIB object to off(2)
automatically, after accepting the command.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	unbalanced
3	balanced

.1.3.6.1.4.1.164.6.2.12.10.1.7

intSwdlToSubSystem

This object defines the subsystem for download.
Bit='1'- APPLY to respective sub system.
Bit='0'- DO NOT APPLY to respective sub system.
For more details see product specification.
For every octet bit0=LSB, bit7=MSB

OctetStringr/w

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.6.2.12.10.1.8

intSwdlCardType

This object defines the Card type that this file is relevant for.

Enumeration

.1.3.6.1.4.1.164.6.2.12.10.1.9

intSwdlFlashIdx

The index of the flash memory this file is stored in (1 or 2)
(Example: 1= The file is stored in flash No.1).
ASMi52 file will always be stored in Flash No.2 (intSwdlFlashIdx=2).

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.12.10.1.10

swdlStatusTable

table

.1.3.6.1.4.1.164.6.2.12.11 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk swdlStatusTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::swdlStatusTable'

This parameters table is for software download status. 
It also includes data about the files down-loaded or 
attempted to be down-loaded.

swdlStatusEntry row .1.3.6.1.4.1.164.6.2.12.11.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

swdlStatusTypeIdx

The index of the down-load type (e.g. external (1) or internal (2)).

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.12.11.1.1

swdlStatusIdx

The index of the status rows.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.12.11.1.2

swdlStatusFileName

The name of the file.

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.6.2.12.11.1.3

swdlStatusSlot

The slot of the updated (or attempted to be updated) object.

SNMPv2-TCDisplayString

Enumerated Values:

1	auto
2	s300bps
3	s1200bps
4	s2400bps
5	s4800bps
6	s9600bps
7	s19200bps
8	s38400bps
9	s57600bps
10	s115200bps

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.6.2.12.11.1.4

swdlStatusSubSystem

The subsystem that updated (or attempted to be updated).

SNMPv2-TCDisplayString

Enumerated Values:

1	dataBits7
2	dataBits8

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.6.2.12.11.1.5

swdlStatusStatus

The status of the down load process.
Value: Fail (2), OK (3), InProcess (4).

SNMPv2-SMIInteger32

Enumerated Values:

1	none
2	odd
3	even

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.12.11.1.6

swdlStatusTime

This MIB parameter indicates the time SW download was finished.
The format shuld be YYYY-MM-DD, hh:mm:ss

SNMPv2-TCDisplayString

Enumerated Values:

1	notApplicable
2	stopBits1
3	stopBits1dot5
4	stopBits2

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.6.2.12.11.1.7

autoFileTransferTable

table

.1.3.6.1.4.1.164.6.2.12.13.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk autoFileTransferTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::autoFileTransferTable'

Scheduling configuration table for 
Agent initiated file transfer.

autoFileTransferEntry row .1.3.6.1.4.1.164.6.2.12.13.1.1

An entry in the table.

Indexes

No indexes recorded

Column Syntax OID

autoFileTransferType

This object defines the type of file to be transferred
by agent.

Enumeration

Enumerated Values:

1	notApplicable
2	on
3	rts
4	dteWait
5	dteIgnore

.1.3.6.1.4.1.164.6.2.12.13.1.1.1

autoFileTransferServerIp

This object defines the IP Address of the
server to which the file is uploaded.

RFC1155-SMIIpAddressr/w

Enumerated Values:

1	notApplicable
2	d0
3	d10
4	d50
5	d100
6	d200
7	d300

Type Constraints:
range: 4

.1.3.6.1.4.1.164.6.2.12.13.1.1.2

autoFileTransferFileName

This object defines the name of
the file to be uploaded.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Enumerated Values:

1	notApplicable
2	on
3	dtr

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.6.2.12.13.1.1.3

autoFileTransferScheduling

This object defines schedule for TFTP Automatic session(s)
initiated by Agent, according to the value selected:
now - initiate immediate single session.

recurrence- initiate single session 'eve…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	none
3	proprietary
4	rip2

.1.3.6.1.4.1.164.6.2.12.13.1.1.4

autoFileTransferTimeRecurrence

This object defines time reccurence interval,
e.g. M can be 'every M days', 'every M hours' etc.
Zero is used to indicate
there's no time reccurence (0= notApplicable).
This object is taken into account only
if autoF…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.12.13.1.1.5

autoFileTransferOccurrenceRecurrence

This object defines Occurrence reccurence interval,
e.g N can be in 'every N alarms', 'every N log entries' etc.
zero is used to indicate
There's no Event Reccurence. (0= notApplicable)
This object is taken into acco…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.12.13.1.1.6

sntpServerTable

table

.1.3.6.1.4.1.164.6.2.14.4.11 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk sntpServerTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::sntpServerTable'

This table contains parameters for each NTP Server. 
Entries in the table can be dynamically created.
	 The entries created by user via sntpServerRowStatus, can also be 
	 changed or removed.
The table may include also Broadcast Servers, when Broadcast 
Client Mode is enabled. These are Servers from which the device 
received timestamp by Broadcast. Their entries are automatically
created by the device. Entries of these Servers cannot 
be changed or removed.

sntpServerEntry row .1.3.6.1.4.1.164.6.2.14.4.11.1

An entry in the NTP Server table.

Indexes

No indexes recorded

Column Syntax OID

sntpServerID

The number (index) of the NTP Server.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.14.4.11.1.1

sntpServerRowStatus

This object enables creation and deletion of entries
in the sntpServerTable.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.6.2.14.4.11.1.2

sntpServerAddressType

Server Address type, indicating IPv4(1) or IPv6(2).

INET-ADDRESS-MIBInetAddressTyper/w

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.164.6.2.14.4.11.1.3

sntpServerAddress

IP Address of the NTP Server.

INET-ADDRESS-MIBInetAddressr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.6.2.14.4.11.1.4

sntpServerPort

Source UDP port of the device for sending requests to
a configured NTP Server.

INET-ADDRESS-MIBInetPortNumberr/w

Type Constraints:
range: 0..65535

.1.3.6.1.4.1.164.6.2.14.4.11.1.5

sntpServerPreference

This object marks the Preferred Server.
1 = Preferred (only one Server can have this value)
2 - Not Preferred.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.14.4.11.1.6

sntpServerAdminStatus

Administrative Status of the NTP Server.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.14.4.11.1.7

sntpServerType

Type of the NTP Server.

Enumeration

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.6.2.14.4.11.1.8

sntpServerLastReceivedTimestamp

Last received Date and Time from the NTP Server, according to
Local Time.
0000 0000 = Not Applicable.

SNMPv2-TCDateAndTime

Type Constraints:
range: 8
range: 11

Description:

A date-time specification.

field octets contents range
----- ------ -------- -----
1 1-2 year* 0..65536
2 3 month …

.1.3.6.1.4.1.164.6.2.14.4.11.1.9

sntpServerLastReceivedStratum

Last received Stratum from the NTP Server.
0xFFFFFFFF = Not Applicable.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.14.4.11.1.10

sntpServerTimeSinceLastReceivedMessage

Time passed since last received message from the NTP Server.

RFC1155-SMITimeTicks

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.14.4.11.1.11

sntpServerSendRequestNow

Upon setting this parameter to 'on', an immediate request
should be sent to the specified NTP Server.
After sending the request, the value 'off' will be resumed.
No action when setting this parameter to 'off'

Enumerationr/w

.1.3.6.1.4.1.164.6.2.14.4.11.1.12

schedXTable

table

.1.3.6.1.4.1.164.6.2.14.5 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk schedXTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::schedXTable'

An Augment to the Schedule table
(schedTable in DISMAN-SCHEDULE-MIB; RFC-3231).

schedXEntry row .1.3.6.1.4.1.164.6.2.14.5.1

An entry in the table.

Indexes

No indexes recorded

Column Syntax OID

schedYear

The year during which the scheduled action should take place.

SNMPv2-SMIUnsigned32r/w

Constraints:
range: 0-86400

.1.3.6.1.4.1.164.6.2.14.5.1.1

schedWeekInMonth

The week in month (schedMonth) during which the scheduled action
should take place.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	fail
3	normal
4	open
5	short
6	shortToCrossPair
7	coupleWithCrossPair

.1.3.6.1.4.1.164.6.2.14.5.1.2

schedParam

A Parameter that might be used whenever the scheduled action takes place.

For summer-time schedule -
This variable represents the time offset (in minutes), meaning:
the number of minutes that should be ad…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	fail
3	normal
4	open
5	short
6	shortToCrossPair
7	coupleWithCrossPair

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.14.5.1.3

physicalConnectorTable

table

.1.3.6.1.4.1.164.6.2.15.1 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk physicalConnectorTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::physicalConnectorTable'

This table includes the connector type of ports or interfaces.

physicalConnectorEntry row .1.3.6.1.4.1.164.6.2.15.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

portIdx

This object is an index of the specific port or interface.
For a port, the index will be as agreed between agent and
application.
For an interface, ifIndex may be used.

SNMPv2-SMIInteger32

Enumerated Values:

2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.1.1.1

physicalConnector

The connector of the port/interface.
other - none of the specified connectors
none - no connector.

Enumeration

.1.3.6.1.4.1.164.6.2.15.1.1.2

portOptWaveLength

Wave Length of an Optical interface/port in [nm] and specification if
Laser or not.
notApplicable - for non-optical ports.

Enumeration

.1.3.6.1.4.1.164.6.2.15.1.1.3

portOptMode

Laser Mode of an Optical Laser interface/port.
notApplicable - for non-Laser ports.

Enumeration

.1.3.6.1.4.1.164.6.2.15.1.1.4

portBalance

This object is according to the port Impedance.
For T1 - always balanced.
For E1 - there are different impedance values for balanced
and unbalanced.

Enumerationr/w

Enumerated Values:

1	all
2	allExceptMng
3	specificVlan

.1.3.6.1.4.1.164.6.2.15.1.1.5

portDdmSupport

SFP (Small Form Pluggable) port -support
Digital Diagnostics Monitoring.

Enumeration

.1.3.6.1.4.1.164.6.2.15.1.1.6

portMfgName

(SFP) Port Manufacturer name
(Maximum - 16 characters).

SNMP-FRAMEWORK-MIBSnmpAdminString

Enumerated Values:

2	local
3	remote

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.6.2.15.1.1.7

portTypicalMaxRange

Maximum range supported by SFP port,
in meter units.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.15.1.1.8

physicalConnectorString

(SFP) connector type. It can be Vendor Specific
(unknown in advance). Being a string, the object is not
affected by any future new connectors.
This object will usually not be used
for drawing the connector.

SNMP-FRAMEWORK-MIBSnmpAdminString

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.6.2.15.1.1.9

portVendorPartNo

SFP Vendor Part Number. Being a string, the object is not
affected by any future new SFPs.

SNMP-FRAMEWORK-MIBSnmpAdminString

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.6.2.15.1.1.10

prtSpTable

table

.1.3.6.1.4.1.164.6.2.15.2.1 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtSpTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtSpTable'

A table.

prtSpEntry row .1.3.6.1.4.1.164.6.2.15.2.1.1

Supervisory port parameter table.

Indexes

No indexes recorded

Column Syntax OID

prtSupervisoryIndex

The SP port index.
For some products, having modules (cards):
The LS byte of the integer is the port index 1..255.
The MS byte is different than 0 only if the port belongs to
a module. In that case it is the module n…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.2.1.1.1

prtSupervisoryRate

This attribute indicates the operation rate (speed) of the
port.
auto - automatic rate selection, by the agent.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.2.1.1.2

prtSupervisoryDataBits

This attribute indicates the number of data bits in an async
frame

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.2.1.1.3

prtSupervisoryParity

This attribute indicates the parity mode in an async frame

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.2.1.1.4

prtSupervisoryStopBits

This attribute indicates the parity mode in an async frame.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.2.1.1.5

prtSupervisoryUsage

This attribute indicates the usage of the SP port.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.2.1.1.6

prtSupervisoryInterface

This attribute indicates the supervisory port interface.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.2.1.1.7

prtSupervisoryCTS

CTS line state.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.2.1.1.8

prtSupervisoryDcdDelay

DCD delay in msec.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.2.1.1.9

prtSupervisoryDSR

DSR line state.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.2.1.1.10

prtSupervisoryRoutProtocol

This attribute indicates the routing protocol of the port.
notApplicable - for DP.

Enumerationr/w

Enumerated Values:

1	loopTiming
2	localTiming
3	throughTiming
4	adaptive
5	master
6	fallback
7	station
255	notApplicable

.1.3.6.1.4.1.164.6.2.15.2.1.1.11

prtPerfTable

table

.1.3.6.1.4.1.164.6.2.15.3.1 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtPerfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtPerfTable'

This table includes G.826 ports or interfaces.

prtPerfEntry row .1.3.6.1.4.1.164.6.2.15.3.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtPerfIdx

This object is an index of the specific port or interface.
For a port, the index will be as agreed between agent and
application.
For an interface, ifIndex may be used.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.3.1.1.1

prtPerfPeriodRef

This object is an index that specifies which period of time, the next
5 objects refer to.
currentPeriod - the period since last prtPerfSaveAndResetCmd received or
since Start-up (if no prtPerfSaveAndResetCmd w…

Enumeration

Enumerated Values:

1	notApplicable
2	e1
3	t1
4	fr
5	hdlc
6	hdsl2
7	shdsl
8	adsl
9	adsl2
10	reAdsl2
11	mPair
12	efm
13	atmIma
14	ds1

.1.3.6.1.4.1.164.6.2.15.3.1.1.2

prtPerfElapsedTime

Elapsed Time in seconds.
- for prtPerfPeriodRef=currentPeriod:
The period since last prtPerfSaveAndResetCmd received or since Start-up
(if no prtPerfSaveAndResetCmd was received since Start-up) until now.
- for prt…

SNMPv2-SMIInteger32

Enumerated Values:

2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.3.1.1.3

prtPerfUAS

Number of Unavailable Seconds for the reference period (prtPerfPeriodRef).

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.3.1.1.4

prtPerfES

Number of Errored Seconds for the reference period (prtPerfPeriodRef).

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	long
3	normal
4	short

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.3.1.1.5

prtPerfSES

Number of Severely Errored Seconds for the reference period (prtPerfPeriodRef).

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	user
3	network

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.3.1.1.6

prtPerfBBE

Number of Background Block (or Frame) Errors for the reference period
(prtPerfPeriodRef).

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	off
3	auto
4	manual
5	adjacent

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.3.1.1.7

prtPerfBlocksPerSec

Blocks per second (or frames per second) of the port/interface indicated by
portIdx. This object is constant for a certain port/interface.
It is not affected by the prtPerfPeriodRef index.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.3.1.1.8

prtPerfTimeTag

Time Tag of Last Period: sysUpTime when last prtPerfSaveAndResetCmd was
executed.
This object is applicable only for prtPerfPeriodRef=lastPeriod.
For prtPerfPeriodRef=currentPeriod, the value will always be 0.

RFC1155-SMITimeTicks

Constraints:
range: 1-1

.1.3.6.1.4.1.164.6.2.15.3.1.1.9

prtPerfSaveAndResetCmd

A command per port/interface, to Save data of Current Period in Last Period
data-set and start a new counting period for Current Period.
This object is applicable only for prtPerfPeriodRef=currentPeriod.
Setting this ob…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	sine
3	square

.1.3.6.1.4.1.164.6.2.15.3.1.1.10

prtTestTable

table

.1.3.6.1.4.1.164.6.2.15.4.1 · 1 row entry · 27 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtTestTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtTestTable'

This table includes test data for ports or interfaces.

prtTestEntry row .1.3.6.1.4.1.164.6.2.15.4.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtTestIdx

This object is an index of the specific port or interface.
For a port, the index will be as agreed between agent and
application.
For an interface, ifIndex may be used.

SNMPv2-SMIInteger32

Constraints:
range: 1-1

.1.3.6.1.4.1.164.6.2.15.4.1.1.1

prtTestCmdAndStatus

Setting this object to a value as detailed further on
(except 0) will initiate a test on the specific port.
The test/s requested will be set according to the respective
bit. The value of this object will be a sum of (…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.4.1.1.2

prtBertCounter

This object indicates the number of BERT errors encountered
during the BERT operation.
It is valid only when BERT (Bit Error Rate Test) is active on the
specific port.
The Counter starts from zero (0) anytime BERT is i…

SNMPv2-SMIInteger32

Enumerated Values:

2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.4.1.1.3

prtTestInitiator

This object indicates who initiated this port's test/s.

Enumeration

.1.3.6.1.4.1.164.6.2.15.4.1.1.4

prtTestTimeout

This object is applicable only when a single
test is running. It indicates the test
activation timeout in minutes.
For RICi-E1T1, RICi-E3T3 and LRS-16, the measurement
unit is in seconds.
When the timeout expires, the…

Integer32r/w

Enumerated Values:

2	l2
3	l3

.1.3.6.1.4.1.164.6.2.15.4.1.1.5

prtTestVctRxResult

This object indicates the result of the Vct on
the cable connected to the RX connector.

Enumeration

Enumerated Values:

2	disabled
3	rx

.1.3.6.1.4.1.164.6.2.15.4.1.1.6

prtTestVctTxResult

This object indicates the result of the Vct on
the cable connected to the TX connector.

Enumeration

Enumerated Values:

2	sa4
3	sa5
4	sa6
5	sa7
6	sa8

.1.3.6.1.4.1.164.6.2.15.4.1.1.7

prtTestVctRxDistance

This object indicates the distance in Meters
to the RX cable Open/ Short location discovered by the Vct.
This parameter is applicable for Vct Result = Normal or Fail only,
Else the value of this parameter will be equa…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.4.1.1.8

prtTestVctTxDistance

This object indicates the distance in Meters
to the TX cable Open/ Short location discovered by the Vct.
This parameter is applicable for Vct Result = Normal or Fail only,
Else the value of this parameter will be equa…

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.4.1.1.9

prtTestVctCmd

Vct command.
on (3) = Start Vct on both cables connected to
RX and TX connectors of this port.
Agent will perform the required command and change automatically
the value of this object to off(2).

Enumerationr/w

Constraints:
range: 0-9

.1.3.6.1.4.1.164.6.2.15.4.1.1.10

prtTestVctRxCrossPair

This object should be equal to the Index (prtTestIdx) of the Rx cross pair.
This object is applicable only for Vct Result = shortToCrossPair or coupleWithCrossPair.
This object was especially created for ETX-202. Curre…

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	noLoop
3	loopDetected

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.4.1.1.11

prtTestVctTxCrossPair

This object should be equal to the Index (prtTestIdx) of the Tx cross pair.
This object is applicable only for Vct Result = shortToCrossPair or coupleWithCrossPair.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.4.1.1.12

prtTestActivationDelay

This object is applicable only when a single test is running.
It indicates test activation delay in seconds.
A Value of 0 indicates that the test starts immediately.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.15.4.1.1.13

prtTestMacSwapLoopDataMode

This object defines which part
of the data will be looped back.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.4.1.1.14

prtTestMacSwapLoopVlanId

This object specifies the VLAN ID for
prtTestMacSwapLoopDataMode=specificVlan.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.4.1.1.15

prtTestMacSwapLoopDirection

This object defines the direction of the performed loopback.
In ETX102 'local' corresponds to Ingress loop
(either on User port or on Network port), and
'remote' corresponds to Egress loop
(either on User port or on Net…

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.4.1.1.16

prtTestMacSwapLoopDestAddr

Configures the MAC address that will be sent in the
Destination field of the packet in the outgoing direction.

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.6.2.15.4.1.1.17

prtTestMacSwapLoopSrcAddr

Configures the MAC address that will be sent in the
Source field of the packet in the outgoing direction.

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.6.2.15.4.1.1.18

prtTestOamMinRoundTripDelay

The mininal value of round trip delay of loopback message for a session of
OAM loopback.Units are msec.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.15.4.1.1.19

prtTestOamMaxRoundTripDelay

The maximum value of round trip delay of loopback message for a session of
OAM loopback.Units are msec.

SNMPv2-SMIUnsigned32

Enumerated Values:

1	notApplicable
2	halfDuplex
3	fullDuplex

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.15.4.1.1.20

prtTestOamAvgRoundTripDelay

The average round trip delay of loopback message for a session of
OAM loopback.Units are msec.

SNMPv2-SMIUnsigned32

Enumerated Values:

1	notApplicable
2	r10Mbps
3	r100Mbps

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.15.4.1.1.21

prtTestOamTxInterval

Indicates the interval between loopback sent messages.Units are msec.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	notApplicable
2	no
3	yes

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.15.4.1.1.22

prtTestDestinationIpAddress

Indicates the destination IP Address in the transmitted messages that
are looped back.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.6.2.15.4.1.1.23

prtTestForceTTL

Time-to-live.Number of hops the loopback message will go through the net
before deciding to discard it.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.15.4.1.1.24

prtTestBwProfiledeprecated

Indicates the BW profile (from bwProfileTable) that is assigned to the loopback test
in order to limit the traffic that is looped back.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.15.4.1.1.25

prtTestSourceIpAddress

Indicates the source IP Address in the transmitted messages that
are looped back.

RFC1155-SMIIpAddressr/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: 4

.1.3.6.1.4.1.164.6.2.15.4.1.1.26

prtTestRemainTime

Indicates the remain time for test activation
in seconds.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	notApplicable
2	low
3	high

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.15.4.1.1.27

prtParamTable

table

.1.3.6.1.4.1.164.6.2.15.5.1 · 1 row entry · 28 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtParamTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtParamTable'

This table includes general port parameters. The meaning is
different for every product that supports it due to a general
parameter - prtControlCnfg.
          
For ACE2002:
-This table is used as a mechanism to create the next interface index.
The algorithm description: 
The NMS will send the agent the following get command: get(nextIfIndex.index), 
where index=interface on which the new index is dependent on. 
Upon this command the agent will generate and return the new index to the NMS.
- This table is partially supported according to the interface type. 
Upon getNext function the irrelevant parameters will be skipped.

prtParamEntry row .1.3.6.1.4.1.164.6.2.15.5.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtParamIdx

This object is an index of the specific port or interface.
For a port, the index will be as agreed between agent and
application.
For an interface, ifIndex may be used.

For ACE2002:
This parameter is the…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.5.1.1.1

prtControlCnfg

This object may be used for port RW general parameter/s.
For detailed meaning, see product's spec.
Supported by: PRBi-E3/T3.

For ACE2002:
This parameter will include the value of the new index
generated …

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.5.1.1.2

prtParamClkSrc

The source of Transmit Clock.
'loopTiming' or 'loopback' indicates that the recovered receive clock
is used as the transmit clock.

'localTiming' or 'internal' indicates that a local clock
source is use…

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.5.1.1.3

prtParamPhantom

Power feeding to another device.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	tcp
3	udp

.1.3.6.1.4.1.164.6.2.15.5.1.1.4

prtParamResetStatsCmd

Reset statistics of the selected port.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.5.1.1.5

prtParamLastResetStatsTime

The value of MIB II's sysUpTime object at the last time that
prtParamResetStatsCmd was Set to on(3) for this port.
If prtParamResetStatsCmd was never Set to on(3) since last
re-initialization of the agent, then this…

SNMPv2-TCTimeStamp

Enumerated Values:

1	notApplicable
2	no
3	yes

Based On: SNMPv2-SMITimeTicks

Description:

The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…

.1.3.6.1.4.1.164.6.2.15.5.1.1.6

prtParamInterfaceType

The type of the port.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.5.1.1.7

prtParamClearAlarm

Setting this attribute to ON, will enforce a clear
operation on the Port Alarms.
Upon completion, the value will automatically change
to off(2).

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.5.1.1.8

prtParamLeds

This entry specifies the LEDs status of the port.
Each led is represented by 4 bits where the first 2 bits
(left) specify the status :
(00=NA, 01=OFF, 10=ON, 11=BLINK),
and the next two bits (right) specify the color :…

OctetString

.1.3.6.1.4.1.164.6.2.15.5.1.1.9

prtParamLineLength

Line Length of the line connected to this port.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.5.1.1.10

prtParamUsage

Defines whether this port works as User port or as Network port.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	unmodified
3	tag
4	doubleTag
5	doubleTagAndFallBack
6	untag

.1.3.6.1.4.1.164.6.2.15.5.1.1.11

prtParamMappingMode

This object defines path protection on SONET/SDH link
Auto - SONET/SDH mapping for port is copied
automatically to same TU on the redundant
SONET/SDH local (reside on same slot) link by agent.
Manual - the user can con…

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.5.1.1.12

prtParamAlarmIndication

This object indicates status-aggregation of non-masked alarms
associated with all interface layers, related to this physical port.
When at least one non-masked alarm exists on any layer,
value of this object is on (3)…

Enumeration

.1.3.6.1.4.1.164.6.2.15.5.1.1.13

prtParamClkQualityLevel

This parameter indicates quality level of clock signal.
Quality is encoded according to SSM
(Synchronization Status Messages) encoding.
Bits 8 -5 of byte are encoded as follows (when bit1=0):
Left most bit - M…

OctetString

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.6.2.15.5.1.1.14

prtParamClkWaveShape

Wave shape of station clock source signal.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.5.1.1.15

prtParamStatus

Station clock source Status.

Enumeration

.1.3.6.1.4.1.164.6.2.15.5.1.1.16

prtParamSignalLevel

This object indicates signal level (in thenth of dB units)
on selected port.

SNMPv2-SMIInteger32

Enumerated Values:

1	all
2	broadMultiFloodedUnicast
3	broadcastMulticast
4	broadcast

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.5.1.1.17

prtParamClkUserQualityLevel

This parameter allows user to mark quality level of clock.
Quality is encoded according to SSM
(Synchronization Status Messages) encoding.
Bits 8 -5 of byte are encoded as follows:
Left most bit - MSB(8) ---> LSB(5)
8…

OctetStringr/w

.1.3.6.1.4.1.164.6.2.15.5.1.1.18

prtParamDataRate

Rate of serial data port (V.11, V.24, V.35)
in kbps units.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.15.5.1.1.19

prtParamLoopDetect

Enable/disable Loop Detection on a port.
Examples of ports: physical, Channelized Bundle over TDM Uplink,
Bridge Ports.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.5.1.1.20

prtParamActUponLoopDetect

This parameter is used to indicate which actions
should be taken in case a loop is detected in the network the port is part of.
Each action is represented by a bit.
Currently defined (for RIC155GE/RIC622GE):
Bit 0 - Tra…

OctetStringr/w

.1.3.6.1.4.1.164.6.2.15.5.1.1.21

prtParamPSNLayer

This object indicates the network layer from which clock is derived.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.5.1.1.22

prtParamRxSsm

This object indicates if Station Clock SSM messages
received will serve as criteria for clock selection.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.5.1.1.23

prtParamClkSsmRxSource

This object indicates the Sa-bit of the E1 frame,
in which SSM messages are carried.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.5.1.1.24

prtParamFarEndDevice

Programmed Far-End device connected to this port.
This object is relevant for products having multiple DBs.
It will enable configuring offline, the relevant data.
For MP-4100, LRS-102 OP-108/106 cards, the options w…

SNMPv2-SMIUnsigned32r/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.6.2.15.5.1.1.26

prtParamTxClk

enable/disable station clock signal output.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.5.1.1.27

prtParamSdBerThreshold

The Signal Degrade Bit Error Rate Threshold.
The negated value of this number is used as the exponent of
10 for computing the threshold value for the Bit Error Rate (BER).
For example, a value of 5 indicates a BER thres…

Unsigned32r/w

Enumerated Values:

1	master
2	fallback

.1.3.6.1.4.1.164.6.2.15.5.1.1.28

prtParamLoopDetectStatus

This object shows whether a loop was detected on the current port.

Enumeration

Enumerated Values:

2	internal
3	rxClk
255	notApplicable

.1.3.6.1.4.1.164.6.2.15.5.1.1.29

prtIpParamTable

table

.1.3.6.1.4.1.164.6.2.15.6.1 · 1 row entry · 38 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtIpParamTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtIpParamTable'

A table - Parameters for IP Ports.

prtIpParamEntry row .1.3.6.1.4.1.164.6.2.15.6.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtIpParamConfigIdx

This object indicates the Configuration number (1..255)
referred.
Value of 255 specifies the TmpCnfg (Scratch).
For products having Agent and Edit configurations,
Write operation for the table entries is allowed only …

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.6.1.1.1

prtIpParamSlotIdx

This object indicates a unique number of the slot position
in which the module is inserted.
notApplicable = 255 (for products that don't have slots).

For KM:
kmxMlA (103),
kmxMlB (104).

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.6.1.1.2

prtIpParamIdx

This object indicates a unique Port Index.

SNMPv2-SMIInteger32

Enumerated Values:

1	actual
2	minimum
3	maximum

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.6.1.1.3

prtIpParamHostIP

The host interface IP address.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.6.2.15.6.1.1.4

prtIpParamHostMask

The host interface subnet mask.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.6.2.15.6.1.1.5

prtIpParamDefaultGateway

Default Gateway's IP Address.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.6.2.15.6.1.1.6

prtIpParamMediaMode

This object indicates the real Media Mode.

Enumeration

.1.3.6.1.4.1.164.6.2.15.6.1.1.7

prtIpParamMediaRate

This object indicates the real Media Rate (Mbps).

Enumeration

.1.3.6.1.4.1.164.6.2.15.6.1.1.8

prtIpParamMngVlanSupport

Management VLAN support (Tagging).
no - No support of VLAN Tagging.
yes - 4 VLAN bytes will be added to the frame.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.6.1.1.9

prtIpParamMngVlanId

Management VLAN ID.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.6.1.1.10

prtIpParamMngVlanPriority

Management VLAN Frame priority.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.6.1.1.11

prtIpParamRingMode

This object indicates If Ring Mode is enabled or not.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.6.1.1.12

prtIpParamProtIpEnable

This object indicates whether a list of Protected IP Addresses
is enabled or not. This object is applicable only if
prtIpParamRingMode=enable.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.6.2.15.6.1.1.13

prtIpParamTrafficPriority

This object indicates the traffic priority of this port.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.6.1.1.14

prtIpParamRemoteIP

This is the IP Address of the remote device that is connected to the
current device (Point to Point Application). It is used for sending OAM packets
on the LAN to the remote side in order to check that the connection is…

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.6.2.15.6.1.1.15

prtIpParamMaxTxBandwidth

This object shows the Max Bandwidth allowed on the LAN.
Full - means that a Maximum of 100 Mega Byte Rate may go through the LAN.
e1(3) means that the maximum is an E1 rate. t1(4) is for a maximum of a T1 rate.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.6.1.1.16

prtIpParamTos

TOS = Type of Service transmitted.
Valid values: 0..255.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.6.1.1.17

prtIpParamConnect

Port Connection.

Enumerationr/w

Enumerated Values:

1	none
2	ac
3	dc
4	acDc
5	acPF
6	dcPF
7	acWithFan
8	dcWithFan

.1.3.6.1.4.1.164.6.2.15.6.1.1.18

prtIpParamAgingTime

Aging Time in seconds.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	failed
3	ok
4	degraded

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.6.1.1.19

prtIpParamEncapsulationProt

Encapsulation Protocol.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	fixed
3	hotSwap

.1.3.6.1.4.1.164.6.2.15.6.1.1.20

prtIpParamEncapProtPort

Encapsulation Protocol Port (TCP/UDP Port).

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.6.1.1.21

prtIpParamVlanSupport

VLAN support (Tagging).
'no' - No support of VLAN Tagging.
'yes' - 4 VLAN bytes will be added to the frame.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.6.1.1.22

prtIpParamVlanId

VLAN Identifier.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.6.1.1.23

prtIpParamVlanPriority

VLAN Frame priority.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.6.1.1.24

prtIpParamDoubleTagVlanId

VLAN Identifier of the Double Tagging VLAN.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.6.1.1.25

prtIpParamDoubleTagVlanPriority

VLAN Frame priority of the Double Tagging VLAN.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.6.1.1.26

prtIpParamVlanTagging

VLAN Tagging.
'unmodified' - No change will be done to the Frame.
'tag' - Add Tag to Untagged Frames.
'doubleTag' - Add Tag to all Frames.
'doubleTagAndFallBack' - Double Tagging will have different rules for
VLANs th…

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.6.1.1.27

prtIpParamRateLimit

The maximum rate permitted to transfer via this port, in Kbps.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.6.1.1.28

prtIpParamDefInterface

The Default Interface for packets with unresolved destination subnet.
For internal-X port: 100 + X .

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.6.1.1.29

prtIpParamMng

This object indicates whether Management is enabled/disabled
via this port.

Enumerationr/w

Enumerated Values:

1	up
2	down

.1.3.6.1.4.1.164.6.2.15.6.1.1.30

prtIpParamFloodedRateLimit

The maximum rate permitted to transfer broadcast, multicast,
and unicast flooded frames via this port, in Kbps.
0 - Disable.
In Ipmux14 this parameter is applicable when prtIpParamRateLimit=0 (disable).

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	up
2	down
3	unknown

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.6.1.1.31

prtIpParamBurstSize

The burst size that the port can support beyond rate limitation
determined in prtIpParamRateLimit.
Burst Size is measured in bytes.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	notApplicable
2	free
3	routerAtm
4	lis

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.15.6.1.1.32

prtIpParamLimitPacketType

The packet type that will be rate limited. Rate limitation
determined in prtIpParamRateLimit.
all - All packet types are rate limited.
broadMultiFloodedUnicast - Broadcast, Multicast and Flooded Unicast packets are r…

Enumerationr/w

Constraints:
range: 1-4

.1.3.6.1.4.1.164.6.2.15.6.1.1.33

prtIpParamKeepAliveInterval

This parameter indicates the period of time (in msec.)
between two consequent Keep Alive messages.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.6.1.1.34

prtIpParamKeepAliveThresh

This parameter indicates the maximum number of
missed Keep Alive answer messages acceptable, after which link status will be failed.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.6.1.1.35

prtIpParamP2pKeepAliveVlanId

Dedicated VLAN ID for keep alive messages.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.6.1.1.36

prtIpParamP2pKeepAliveVlanPrio

VLAN priority for P2P keep alive messages .

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.6.1.1.37

prtIpParamRingAdjacentMacAddr

The MAC address of the adjacent NE connected to this port in an ETH ring.
If the port is not a member of a ring, the value of this parameter
will be 00-00-00-00-00-00.

MacAddress

Enumerated Values:

2	off
3	on
4	factory

Type Constraints:
range: 6

.1.3.6.1.4.1.164.6.2.15.6.1.1.38

prtClkSrcTable

table

.1.3.6.1.4.1.164.6.2.15.7.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtClkSrcTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtClkSrcTable'

A table - Parameters for  master and fallback 
clock source of ports .

prtClkSrcEntry row .1.3.6.1.4.1.164.6.2.15.7.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtClkSrcCnfgIdx

This attribute indicates the Idx of the Cnfg(1..255) being
accessed ; Idx of 255 relates to the TmpCnfg.

Integer32

Enumerated Values:

2	unknown
3	empty
4	miRicE1
5	miRicT1
6	miRicE3
7	miRicT3

.1.3.6.1.4.1.164.6.2.15.7.1.1.1

prtClkSrcPrtIdx

This object indicates a unique Port Index (receiving clock).
Refer to device specification for port Index

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.7.1.1.2

prtClkSrcIdx

An index in the table.
master - refers Master clock parameters
fallback - refers Fallback clock parameters

Enumeration

.1.3.6.1.4.1.164.6.2.15.7.1.1.3

prtClkSrcMode

This entry indicates the source the nodal timing is
locked to.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.15.7.1.1.4

prtClkSrcPrt

This entry is valid only when working in rxClk mode.
It specifies the port from which the clock willl be taken.
Refer to device specification for source port Index

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.15.7.1.1.5

optPrtMonitorTable

table

.1.3.6.1.4.1.164.6.2.15.8.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk optPrtMonitorTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::optPrtMonitorTable'

A table -  optical port (e.g SFP) monitoring parameters,
according to SFF-8472 Specification for Diagnostic Monitoring 
	 Interface for Optical Xcvrs. and ITU-T rec. G.958

optPrtMonitorEntry row .1.3.6.1.4.1.164.6.2.15.8.1.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
optPrtMonitorPrtIdx This object indicates a unique (optical) Port Index . Refer to device specification for port Index.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.6.2.15.8.1.1.1`
optPrtMonitorSample This index indicates historic and current values - minimum, maximum and actual (current) value.	Enumeration	`.1.3.6.1.4.1.164.6.2.15.8.1.1.2`
optPrtMonitorTxPower Transmitted optical power level. Value is given in units of hundredth (1/100) of dBm.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.6.2.15.8.1.1.3`
optPrtMonitorLaserBias LASER bias current level. Value is given in units of microAmper (uA).	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.6.2.15.8.1.1.4`
optPrtMonitorLaserTemp LASER temperature level, in hundredth (1/100) (C) degrees.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.6.2.15.8.1.1.5`
optPrtMonitorRxPower Received optical power in units of hundredth (1/100) of dBm.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.6.2.15.8.1.1.6`
optPrtMonitorSupplyVoltage Supply voltage, in hundredth (1/100) of volts (V).	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.6.2.15.8.1.1.7`

optPrtCnfgTable

table

.1.3.6.1.4.1.164.6.2.15.8.2 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk optPrtCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::optPrtCnfgTable'

A table -  optical port configuration

optPrtCnfgEntry row .1.3.6.1.4.1.164.6.2.15.8.2.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
optPrtCnfgIdx This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.x.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.2.15.8.2.1.1`
optPrtCnfgPrtIdx This object indicates a unique (optical) Port Index . Refer to device specification for port Index.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.2.15.8.2.1.2`
optPrtCnfgALS enable/disable Automatic Laser Shutdown	Enumerationr/w	`.1.3.6.1.4.1.164.6.2.15.8.2.1.3`

systemPsTable

table

.1.3.6.1.4.1.164.6.2.25 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk systemPsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::systemPsTable'

This table describes the PS types of a device.
Usage of this table is specified in the device's NMS SRS

systemPsEntry row .1.3.6.1.4.1.164.6.2.25.1

An entry in table.

Indexes

systemOamCnfgIdx

Column Syntax OID

systemPsIndex1

First Index.
In HUBs:
1 = PS-A slot
2 = PS-B slot
3 = PS-C slot.
In SA units:
1 = PS1
2 = PS2
Default = 1

SNMPv2-SMIInteger32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.6.2.25.1.1

systemPsIndex2

Second Index.
In HUBs:
1 always.
In SA units:
1 = Local
2 = Remote
Default = 1.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.25.1.2

systemPsType

The type of PS, for a stand-alone product.
acDc - PS that supports both AC and DC.
acPF - Power Feeding (phantom) box that is feeding another box by external AC.
dcPF - Power Feeding (phantom) box that is feeding anothe…

Enumeration

.1.3.6.1.4.1.164.6.2.25.1.3

systemPsStatus

The Status of the PS unit.

Enumeration

Enumerated Values:

2	disable
3	enable

.1.3.6.1.4.1.164.6.2.25.1.4

systemPsHotSwap

Is PS unit hot swap or fixed.

Enumeration

.1.3.6.1.4.1.164.6.2.25.1.5

xcTable

table

.1.3.6.1.4.1.164.6.2.31 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk xcTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::xcTable'

Configuration of system cross-connect entries.
The table follows the behavior described in RFC 2515, 
RFC 1604 regarding the creation deletion and modification 
of an entry within the table.

xcEntry row .1.3.6.1.4.1.164.6.2.31.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

xcIndex

Cross Connect Identifier.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.31.1.1

xcIfIndex1

The interface Index from the ifTable, which identify one side
of the connection.

SNMPv2-SMIInteger32

Enumerated Values:

1	intermediate
2	segmentTermination
3	endToEndTermination

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.31.1.2

xcVpi

The VPI value.

SNMPv2-SMIInteger32

Enumerated Values:

2	both
3	none
4	source
5	sink

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.31.1.3

xcVci

The VCI value.

SNMPv2-SMIInteger32

Enumerated Values:

2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.31.1.4

xcIfIndex2

The interface Index from the ifTable, which identifies the other
side of the connection.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.31.1.5

xcRowStatus

This parameter allows NMS to create/delete entries of this table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.6.2.31.1.6

xcDescr

A textual string containing information about the
xc entry.

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.6.2.31.1.7

xcAdminStatus

The desired administrative status of this
bi-directional cross-connect.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.31.1.8

xcOperStatus

The operational status of this bi-directional
cross-connect.

Enumeration

.1.3.6.1.4.1.164.6.2.31.1.9

xcAttachedIfType

This object indicates if the specific VCC is
already attached to any interface, and indicates
the type of the interface.
This object's purpose is to ease the checking to
the NMS.
notApplicable - used for entries that a…

Enumeration

.1.3.6.1.4.1.164.6.2.31.1.10

xcInputPriority

This object is the priority, by which the LAN frames will be
internaly sent to the ATM HW. This parameter is applicable if
atmNteMdlInputPriorityMechanism=enabled.

1 - Highest priority. Will be the fir…

Integer32r/w

.1.3.6.1.4.1.164.6.2.31.1.11

xcBitMapping

This object maps this entry to a bit of an octet string.
For ACE2002 this object maps the LAN VCC to the bit of the
VLAN Port Lists. If the value is '0' then it means that
this VCC is not mapped to a port list or it m…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.31.1.12

modlParamTable

table

.1.3.6.1.4.1.164.6.2.32.1.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk modlParamTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::modlParamTable'

This table include parameters for system modules.

modlParamEntry row .1.3.6.1.4.1.164.6.2.32.1.1.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
modlParamIndex The module index. The index can be the slot number or any other module index as described in the specifications of the device. For Vmux-2100 device, the index will have values of: 1..4 for slots 1..4.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.6.2.32.1.1.1.1`
modlParamReset Reset action to be performed on the module. Set the parameter will be done always to on(3) or factory (4). After performing the Reset operation, Agent will automatically set the parameter to off(2).	Enumerationr/w	`.1.3.6.1.4.1.164.6.2.32.1.1.1.2`
modlParamSwdlStatus This parameter indicates whatever the swdl is in process or not.	Enumeration	`.1.3.6.1.4.1.164.6.2.32.1.1.1.3`
modlParamLeds This entry specifies the LEDs status of the module. Each led is represented by 4 bits where the first 2 bits (left) specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) specify the color…	OctetString	`.1.3.6.1.4.1.164.6.2.32.1.1.1.4`
modlParamType This attribute indicates the Module Type.	Enumeration	`.1.3.6.1.4.1.164.6.2.32.1.1.1.5`
modlParamSwVer This attribute indicates the Module's Software Version.	SNMPv2-TCDisplayString Type Constraints: `range: 0..255` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.164.6.2.32.1.1.1.6`

ifCreateTable

table

.1.3.6.1.4.1.164.6.2.35.1 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ifCreateTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ifCreateTable'

The Interface Configuration Table.
This table enables to create interfaces of Entities.

ifCreateEntry row .1.3.6.1.4.1.164.6.2.35.1.1

An entry in the Interface Configuration table.

Indexes

No indexes recorded

Column Syntax OID

ifCreateEntityType

This object indicates the Type of the Entity that exists above the created interface.
For a Logical Port, this value can be: other (1) when there is no fixed entity above it.

SysIfEntityType

Type Values:

1	other
6	ethernetLan
37	atm
62	fastEther
142	ipForward
200	teLink
209	bridge

.1.3.6.1.4.1.164.6.2.35.1.1.1

ifCreateEntityIdx

This object indicates the Index of the Entity that exists above the created interface.
For a Logical Port, this value can be: 9999 - N/A when there is no fixed entity above it.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.35.1.1.2

ifCreateNumber

This object indicates the number of the Interface that is created.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.35.1.1.3

ifCreateRowStatus

This object enables the user to
create/delete entries in this table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.6.2.35.1.1.4

ifCreateType

This object indicates the Type of the Interface that is created.

IANAifType-MIBIANAifTyper/w

Constraints:
range: 1-64

Type Values:

1	other
2	regular1822
3	hdh1822
4	ddnX25
5	rfc877x25
6	ethernetCsmacd
7	iso88023Csmacd
8	iso88024TokenBus
9	iso88025TokenRing
10	iso88026Man
11	starLan
12	proteon10Mbit
13	proteon80Mbit
14	hyperchannel
15	fddi
16	lapb
17	sdlc
18	ds1
19	e1
20	basicISDN
21	primaryISDN
22	propPointToPointSerial
23	ppp
24	softwareLoopback
25	eon
26	ethernet3Mbit
27	nsip
28	slip
29	ultra
30	ds3
31	sip
32	frameRelay
33	rs232
34	para
35	arcnet
36	arcnetPlus
37	atm
38	miox25
39	sonet
40	x25ple
41	iso88022llc
42	localTalk
43	smdsDxi
44	frameRelayService
45	v35
46	hssi
47	hippi
48	modem
49	aal5
50	sonetPath
51	sonetVT
52	smdsIcip
53	propVirtual
54	propMultiplexor
55	ieee80212
56	fibreChannel
57	hippiInterface
58	frameRelayInterconnect
59	aflane8023
60	aflane8025
61	cctEmul
62	fastEther
63	isdn
64	v11
65	v36
66	g703at64k
67	g703at2mb
68	qllc
69	fastEtherFX
70	channel
71	ieee80211
72	ibm370parChan
73	escon
74	dlsw
75	isdns
76	isdnu
77	lapd
78	ipSwitch
79	rsrb
80	atmLogical
81	ds0
82	ds0Bundle
83	bsc
84	async
85	cnr
86	iso88025Dtr
87	eplrs
88	arap
89	propCnls
90	hostPad
91	termPad
92	frameRelayMPI
93	x213
94	adsl
95	radsl
96	sdsl
97	vdsl
98	iso88025CRFPInt
99	myrinet
100	voiceEM
101	voiceFXO
102	voiceFXS
103	voiceEncap
104	voiceOverIp
105	atmDxi
106	atmFuni
107	atmIma
108	pppMultilinkBundle
109	ipOverCdlc
110	ipOverClaw
111	stackToStack
112	virtualIpAddress
113	mpc
114	ipOverAtm
115	iso88025Fiber
116	tdlc
117	gigabitEthernet
118	hdlc
119	lapf
120	v37
121	x25mlp
122	x25huntGroup
123	transpHdlc
124	interleave
125	fast
126	ip
127	docsCableMaclayer
128	docsCableDownstream
129	docsCableUpstream
130	a12MppSwitch
131	tunnel
132	coffee
133	ces
134	atmSubInterface
135	l2vlan
136	l3ipvlan
137	l3ipxvlan
138	digitalPowerline
139	mediaMailOverIp
140	dtm
141	dcn
142	ipForward
143	msdsl
144	ieee1394
145	if-gsn
146	dvbRccMacLayer
147	dvbRccDownstream
148	dvbRccUpstream
149	atmVirtual
150	mplsTunnel
151	srp
152	voiceOverAtm
153	voiceOverFrameRelay
154	idsl
155	compositeLink
156	ss7SigLink
157	propWirelessP2P
158	frForward
159	rfc1483
160	usb
161	ieee8023adLag
162	bgppolicyaccounting
163	frf16MfrBundle
164	h323Gatekeeper
165	h323Proxy
166	mpls
167	mfSigLink
168	hdsl2
169	shdsl
170	ds1FDL
171	pos
172	dvbAsiIn
173	dvbAsiOut
174	plc
175	nfas
176	tr008
177	gr303RDT
178	gr303IDT
179	isup
180	propDocsWirelessMaclayer
181	propDocsWirelessDownstream
182	propDocsWirelessUpstream
183	hiperlan2
184	propBWAp2Mp
185	sonetOverheadChannel
186	digitalWrapperOverheadChannel
187	aal2
188	radioMAC
189	atmRadio
190	imt
191	mvl
192	reachDSL
193	frDlciEndPt
194	atmVciEndPt
195	opticalChannel
196	opticalTransport
197	propAtm
198	voiceOverCable
199	infiniband
200	teLink
201	q2931
202	virtualTg
203	sipTg
204	sipSig
205	docsCableUpstreamChannel
206	econet
207	pon155
208	pon622
209	bridge
210	linegroup
211	voiceEMFGD
212	voiceFGDEANA
213	voiceDID
214	mpegTransport
215	sixToFour
216	gtp
217	pdnEtherLoop1
218	pdnEtherLoop2
219	opticalChannelGroup
220	homepna
221	gfp
222	ciscoISLvlan
223	actelisMetaLOOP
224	fcipLink
225	rpr
226	qam
227	lmp
228	cblVectaStar
229	docsCableMCmtsDownstream
230	adsl2
231	macSecControlledIF
232	macSecUncontrolledIF
233	aviciOpticalEther
234	atmbond
235	voiceFGDOS
236	mocaVersion1
237	ieee80216WMAN
238	adsl2plus
239	dvbRcsMacLayer
240	dvbTdm
241	dvbRcsTdma
242	x86Laps
243	wwanPP
244	wwanPP2
245	voiceEBS
246	ifPwType
247	ilan
248	pip
249	aluELP
250	gpon
251	vdsl2
252	capwapDot11Profile
253	capwapDot11Bss
254	capwapWtpVirtualRadio
255	bits
256	docsCableUpstreamRfPort
257	cableDownstreamRfPort
258	vmwareVirtualNic
259	ieee802154
260	otnOdu
261	otnOtu
262	ifVfiType
263	g9981
264	g9982
265	g9983
266	aluEpon
267	aluEponOnu
268	aluEponPhysicalUni
269	aluEponLogicalLink
270	aluGponOnu
271	aluGponPhysicalUni
272	vmwareNicTeam
277	docsOfdmDownstream
278	docsOfdmaUpstream
279	gfast
280	sdci
281	xboxWireless
282	fastdsl
283	docsCableScte55d1FwdOob
284	docsCableScte55d1RetOob
285	docsCableScte55d2DsOob
286	docsCableScte55d2UsOob
287	docsCableNdf
288	docsCableNdr
289	ptm
290	ghn
291	otnOtsi
292	otnOtuc
293	otnOduc
294	otnOtsig
295	microwaveCarrierTermination
296	microwaveRadioLinkTerminal
297	ieee8021axDrni
298	ax25
299	ieee19061nanocom
300	cpri
301	omni
302	roe
303	p2pOverLan

.1.3.6.1.4.1.164.6.2.35.1.1.5

ifCreateIndex

This object indicates the ifIndex of the created Interface.
The ifIndex is assigned by the device.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.35.1.1.6

ifCreateConnectedTo

This object indicates the entity connected to the created Interface.
The value of this object can be ifIndex of the connected entity or any other
number that can identify it.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.35.1.1.7

ifCreateParams

This object represents one or more parameters of the created Interface.
Each group of bits (one or more bits) represents a specific parameter
and its possible values.
This object's mapping and interpretation will be spe…

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.35.1.1.8

ifCreateConnectionPointer

This parameter represents the entity that is connected
to this Interface.

It can be used instead of ifCreateConnectedTo.

It is an OBJECT IDENTIFIER.
This parameter's SYNTAX allows t…

SNMPv2-TCRowPointerr/w

Description:

.1.3.6.1.4.1.164.6.2.35.1.1.9

ifPerfTable

table

.1.3.6.1.4.1.164.6.2.35.2.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ifPerfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ifPerfTable'

Interface Performance Table.
The propose of this table is to support statistics counters having 64 bit 
by using 2 parameters with syntax= Integer32.
This is because SNMPv1 does not support Counter64 properly.
For SNMPv3, ifPerfHCCounter (Counter64) may be supported.

ifPerfEntry row .1.3.6.1.4.1.164.6.2.35.2.1.1

An entry in the Interface Performance Table.

Indexes

No indexes recorded

Column	Syntax	OID
ifPerfCounterType 2nd index of the ifPerfTable. This parameter represents the Counter Type. Each application can have a different association between this object's value and counter type - see relevant application spec. For VPLS-MTU appl…	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.6.2.35.2.1.1.1`
ifPerfLowCounterPart In order to support Counters having 64 bit length, the performance counter is divided into two 32 bit parameters as follows: [ 64 bit parameter ] = [ High 32 bit parameter ][ Low 32 bit parameter ]. This parameter h…	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.2.35.2.1.1.2`
ifPerfHighCounterPart This parameter holds the High 32 bits of the counter (see description in the above parameter).	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.2.35.2.1.1.3`
ifPerfHCCounter This High Capacity counter holds whole 64 bits of the counter indicated by ifPerfCounterType (concatenates both counter parts ifPerfHighCounterPart&ifPerfLowCounterPart) This object can be supported only by agents usi…	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.164.6.2.35.2.1.1.4`

systemOamTable

table

.1.3.6.1.4.1.164.6.2.36.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk systemOamTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::systemOamTable'

The OAM Configuration Table.

systemOamEntry row .1.3.6.1.4.1.164.6.2.36.1.1

An entry in the OAM table.

Indexes

No indexes recorded

Column	Syntax	OID
systemOamCnfgIdx This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.	Integer32	`.1.3.6.1.4.1.164.6.2.36.1.1.1`
systemOamFrequency Time in sec. between 2 OAM packets.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.6.2.36.1.1.2`
systemOamTimeoutCycles No. of cycles the agent will send OAM packets without receiving a response from the remote device before declaring that the connection to the remote side is down - Time Out.	SNMPv2-SMIInteger32r/w Constraints: `range: 0-2147483647`	`.1.3.6.1.4.1.164.6.2.36.1.1.3`
systemOamLinkCheck This MIB object determines whether continuous connectivity Link checks will be performed by the device for uplinks. For Vmux-2100: enable (3) value can be set upon device installation. In this case, TDM L…	Enumerationr/w Constraints: `range: 0-2147483647`	`.1.3.6.1.4.1.164.6.2.36.1.1.4`

systemOamDescrTable

table

.1.3.6.1.4.1.164.6.2.36.2 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk systemOamDescrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::systemOamDescrTable'

The OAM Descriptors Configuration Table.

systemOamDescrEntry row .1.3.6.1.4.1.164.6.2.36.2.1

An entry in the OAM table.

Indexes

No indexes recorded

Column Syntax OID

systemOamDescrIdx

The OAM Descriptor Index.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.36.2.1.1

systemOamDescrRowStatus

Enables the user to create/delete entries in this table.

SNMPv2-TCRowStatusr/w

Enumerated Values:

0	loss
1	ais
2	rdi
3	protocolDown
4	oamSignalingEfm
5	oamSignalingCfm

Description:

.1.3.6.1.4.1.164.6.2.36.2.1.2

systemOamDescrMode

The OAM Mode of the Descriptor.

Enumerationr/w

Enumerated Values:

1	manual
2	automatic

.1.3.6.1.4.1.164.6.2.36.2.1.3

systemOamDescrCCDirection

OAM Continuity Check function mode.
both(2) - Agent sends OAM CC cells and checks received OAM CC cells.
none(3) - Agent does not send and does not check received OAM CC cells.
source(4)- Agent sends OAM CC cells.
sink…

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.6.2.36.2.1.4

systemOamDescrLoopbackOperation

The OAM Loopback function mode.
off(2) - Stop sending loopback OAM cells.
on(3) - Start loopback OAM cells.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.36.2.1.5

systemOamDescrLoopbackDestAddr

Loopback Destination Address.

OctetStringr/w

Enumerated Values:

1	unidirectional
2	bidirectional

.1.3.6.1.4.1.164.6.2.36.2.1.6

systemOamDescrXcCounter

The number of connections that use this OAM Descriptor.

SNMPv2-SMIGauge32

Enumerated Values:

0	noAction
1	interfaceDeactivation
2	oamSignaling

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.36.2.1.7

bitMappingTable

table

.1.3.6.1.4.1.164.6.2.38 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk bitMappingTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::bitMappingTable'

This table maps bits of an octet string to an interface.
For ACE-2002 this table is used to map bits of VLAN port lists
to LAN VCC's. This table is the opposite view of the xcTable for
xcBitMapping. It is used to ease the bit translation for the NMS.

bitMappingEntry row .1.3.6.1.4.1.164.6.2.38.1

Each entry in the table describes a correlation of a bit location to
an interface.
For ACE-2002 - Upon creation of a new LAN VCC the agent will add an
entry to this table that will define the bit location for that VCC.

Indexes

agnClkSrcPortCnfgIdx agnClkSrcPortSrcIdx agnClkSrcPortIdx

Column Syntax OID

bitMappingLocation

The bit location in an octet string.

SNMPv2-SMIInteger32

Constraints:
range: 1-2147483647

.1.3.6.1.4.1.164.6.2.38.1.1

bitMappingIndex

The interface index or any other index that should be mapped.

SNMPv2-SMIInteger32

Enumerated Values:

1	master
2	fallback
3	recovered

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.38.1.2

hostTable

table

.1.3.6.1.4.1.164.6.2.40 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk hostTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::hostTable'

Host interface table.

hostEntry row .1.3.6.1.4.1.164.6.2.40.1

An entry in the Host Table.
The hostParam1, hostParam2, and hostParam3 entries may
have different use in different applications.

Indexes

No indexes recorded

Column Syntax OID

hostIndex

The Host Table Index. This index can have the same value as Host No.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.40.1.1

hostIP

The host interface IP address.

RFC1155-SMIIpAddressr/w

Enumerated Values:

1	notApplicable
2	down
3	up

Type Constraints:
range: 4

.1.3.6.1.4.1.164.6.2.40.1.2

hostIPMask

The host interface subnet mask.

RFC1155-SMIIpAddressr/w

Enumerated Values:

1	notApplicable
2	adaptive
3	ieee1588v2
4	commonClock

Type Constraints:
range: 4

.1.3.6.1.4.1.164.6.2.40.1.3

hostDefaultNextHop

The host interface Default Next Hop address.

RFC1155-SMIIpAddressr/w

Enumerated Values:

1	notApplicable
2	stratum1
3	stratum2
4	stratum3
5	stratum3e
6	stratum4

Type Constraints:
range: 4

.1.3.6.1.4.1.164.6.2.40.1.4

hostMode

This parameter represents the Host mode of operation.
There can be different values for each application.
For example:
Not Applicable = 1.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	typeA
3	typeB
4	typeC
5	typeD
6	typeE
7	typeF

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.40.1.5

hostParam1

This parameter represents the first Host parameter.
There can be different values for each application.
For example:
Not Applicable = 1.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	freeRun
2	frequencyAcquisition
3	rapidPhaseLock
4	finePhaseLock
5	holdover
6	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.40.1.6

hostParam2

This parameter represents the 2nd Host parameter.
There can be different values for each application.

SNMPv2-SMIInteger32r/w

Enumerated Values:

3	rxClock
12	recovered

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.40.1.7

hostParam3

This parameter represents the 3nd Host parameter.
There can be different values for each application.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.40.1.8

hostRowStatus

Creation/Deletion of rows in the table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.6.2.40.1.9

hostVlanTagging

Host VLAN support (Tagging).
untag - No support of VLAN Tagging.
tag - 4 VLAN bytes will be added to the frame.

Enumerationr/w

Constraints:
range: 1-2147483647

.1.3.6.1.4.1.164.6.2.40.1.10

hostVlanId

Host VLAN ID.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	master
2	fallback
3	internal

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.40.1.11

hostVlanPriority

Host VLAN Frame priority.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	none
2	internal
3	rxClk
4	station
5	lbt
6	ntr
7	adaptive
8	stationB
9	automatic
10	system
11	sSubsystem
12	recovered
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.40.1.12

invNameXCTable

table

.1.3.6.1.4.1.164.6.2.41 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk invNameXCTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::invNameXCTable'

Inverse Name XC Table.
This table can be used to ease the search for a connection first index
by the connection name.

invNameXCEntry row .1.3.6.1.4.1.164.6.2.41.1

An entry in the table.

Indexes

No indexes recorded

Column Syntax OID

invNameXC

The unique Connection name,
associated to a Cross-Connection.

OctetString

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.6.2.41.1.1

invNameXCType

The OBJECT IDENTIFIER of the respective XC Table.
Examples:

XC Table invNameXCType
---------------------------------------------------
atmVpCrossConnectTable 1.3.6.1.2.1.37.1.9
atmVcCrossConnectTable…

ObjectIdentifier

Enumerated Values:

1	freeRun
2	rapidPhaseLock
3	finePhaseLock
4	holdover
5	frequencyAcquisition

.1.3.6.1.4.1.164.6.2.41.1.2

invNameXCIndex

The XC Table (invNameXCType) may include more than one index.
This object represents the value of the first XC Index.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	disqualified
3	qualified

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.41.1.3

rowInfoTable

table

.1.3.6.1.4.1.164.6.2.43 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk rowInfoTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::rowInfoTable'

This table holds information of other tables.

rowInfoEntry row .1.3.6.1.4.1.164.6.2.43.1

An entry in the table.

Indexes

agnClkCurrentIndex

Column	Syntax	OID
rowInfoTableId The OBJECT IDENTIFIER of the Table, which its information is held by this table (rowInfoTable). Examples: Table Name rowInfoTableId --------------------------------------------------- atmTrafficDescr…	ObjectIdentifier	`.1.3.6.1.4.1.164.6.2.43.1.1`
rowInfoCounter The Number of rows in the table, indicated by rowInfoTableId.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.6.2.43.1.2`
rowInfoIndexNext The First Free Index of the table, indicated by rowInfoTableId.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.6.2.43.1.3`
rowInfoMaxNoOfRows The maximum possible number of rows in the table, indicated by rowInfoTableId.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.6.2.43.1.4`

agnFunctionTable

table

.1.3.6.1.4.1.164.6.2.45 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnFunctionTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnFunctionTable'

This table is used in order to activate/deactivate device functions.
The index indicates the function. Each function can be Enabled or Disabled.

agnFunctionEntry row .1.3.6.1.4.1.164.6.2.45.1

An entry in the table.

Indexes

No indexes recorded

Column	Syntax	OID
agnFunction This MIB object indicates the function that will be enabled or disabled in the device. alarmForwarding= Fault Propagation (usually towards user port). For Vmux: routing (2) - enable/disable Router backup (3) - enable…	Enumeration	`.1.3.6.1.4.1.164.6.2.45.1.1`
agnFunctionActivation This MIB object indicates the activation of the current function.	Enumerationr/w	`.1.3.6.1.4.1.164.6.2.45.1.2`

alarmForwardingTable

table

.1.3.6.1.4.1.164.6.2.50 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk alarmForwardingTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::alarmForwardingTable'

The Alarm Forwarding Mechanism will be operated 
for this table entries.

alarmForwardingEntry row .1.3.6.1.4.1.164.6.2.50.1

Each entry in this table is a pair of ports that
the Alarm Forwarding Mechanism is determined for.

Indexes

No indexes recorded

Column Syntax OID

alarmForwardingFailPort

An Index of the port on which a fail occurs.

Integer32

.1.3.6.1.4.1.164.6.2.50.1.1

alarmForwardingToPort

An Index of the port that will be affected
upon the failure of the alarmForwardingFailPort.

Integer32

.1.3.6.1.4.1.164.6.2.50.1.2

alarmForwardingRowStatus

Creation/ Deletion of rows in the table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.6.2.50.1.3

alarmForwardingRecoveryTime

This parameter defines the maximum time (sec)
the affected port will hold the down state.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.50.1.4

alarmForwardingGroupConditions

This parameter is applicable when there is a group of interfaces
in which a fault may occur, and one interface to which alarm is propagated (forwarded).
0 = All - Forwarding will take place only when all interfaces of …

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.2.50.1.5

alarmForwardingCause

Bit map representing the cause upon which alarm forwarding will take place.
bit 0 - LOSS (LINE DOWN)
bit 1 - AIS
bit 2 - RDI
bit 3 - PROTOCOL DOWN.
bit 4 - OAM Signaling - EFM
bit 5 - OAM Signaling - CFM.

Bitsr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.6.2.50.1.6

alarmForwardingRecoveryMode

This parameter determines the Recovery Mode.
manual - The user should stop the alarm forwarding
by using the alarmForwardingRecoveryCommand.
automatic - Alarm forwarding will be automatically
stopped upon alarmForwar…

Enumerationr/w

.1.3.6.1.4.1.164.6.2.50.1.7

alarmForwardingRecoveryCommand

This parameter is a command. It is applicable when
alarmForwardingRecoveryMode = manual.
on - Will stop alarm forwarding.
After setting to 'On', the agent will set this parameter back to 'Off'.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.50.1.8

alarmForwardingDelay

This parameter determines the period of time (in seconds) the
alarm of the alarmForwardingFailPort should exist before
starting alarm forwarding.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

2	portBased
3	oneToOne
4	sourceMac
5	destinationMac
6	sourceXorDestinationMac
7	sourceAndDestinationMac
8	sourceIp
9	destinationIp
10	sourceAndDestinationMacAndIp
11	roundRobin

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.50.1.9

alarmForwardingDirection

This parameter determines the Direction of the Alarm Forwarding.
unidirectional - alarmForwardingFailPort affects the
alarmForwardingToPort.
bidirectional - alarmForwardingFailPort affects the
…

Enumerationr/w

Enumerated Values:

2	nonRevertive
3	revertive

.1.3.6.1.4.1.164.6.2.50.1.10

alarmForwardingAction

Bit map representing the action to be performed when alarm forwarding will take place.
bit 0 - No Action.
'1' value - device should NOT perform any action, though other bits
indicate the ac…

Bitsr/w

Constraints:
range: 0-720

.1.3.6.1.4.1.164.6.2.50.1.11

agnClkSrcPortTable

table

.1.3.6.1.4.1.164.6.2.52.1 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnClkSrcPortTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnClkSrcPortTable'

Pool of Ports for the Master/Fallback Clock Source
and of Recovered IDs.
For devices with more than one configuration:
Set operation is valid only to the TmpCnfg entry.

agnClkSrcPortEntry row .1.3.6.1.4.1.164.6.2.52.1.1

An entry in the table.

Indexes

No indexes recorded

Column Syntax OID

agnClkSrcPortCnfgIdx

This object indicates the Idx of the Cnfg being
accessed ; Idx of 255 relates to the TmpCnfg.
For product supporting a single configuration, the value will be 1.

Integer32

Enumerated Values:

1	loadSharing
2	redundancy

.1.3.6.1.4.1.164.6.2.52.1.1.1

agnClkSrcPortSrcIdx

Clock Source Index.
master - refers to Master clock
fallback - refers to Fallback clock
recovered - refers to Recovered clock.

Enumeration

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.6.2.52.1.1.2

agnClkSrcPortIdx

This object indicates the running Idx of the Port/Recovered ID that is
to be used as Clock Source, for each agnClkSrcPortSrcIdx instance.

Integer32

.1.3.6.1.4.1.164.6.2.52.1.1.3

agnClkSrcPort

This object indicates the Port/Interface/Recovered ID # that is
to be used as Clock Source.
In case of agnClkSrcPortSrcIdx=recovered (3) - it indicates the PW number.
When agnClkSrcPortSrcIdx=master(1) or fallback(2), …

Integer32r/w

.1.3.6.1.4.1.164.6.2.52.1.1.4

agnClkSrcPortRowStatus

This object enables Creation/ Deletion of rows in the table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.6.2.52.1.1.5

agnClkSrcPortAdminStatus

This object indicates the Recovered Clock Administrative Status.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.52.1.1.6

agnClkSrcPortType

This object is relevant only in case of Recovery Clock.
It indicates the Clock Type.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.52.1.1.7

agnClkSrcPortQuality

This object indicates the Clock Source Quality.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.52.1.1.8

agnClkSrcPortNetType

This object is relevant only in case of Recovery Clock.
It indicates the Clock Network Type, i.e.
the PSN network characteristics and behavior.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.52.1.1.9

agnClkSrcPortState

This object indicates the Clock State.

freeRun(1) -
Clock recovery is not locked to any clock.

frequencyAcquisition(2) -
Adaptive clock recovery is learning the frequency.

ra…

Enumeration

Enumerated Values:

2	disable
3	enable

.1.3.6.1.4.1.164.6.2.52.1.1.10

agnClkSrcPortSrcType

This object indicates the Src Type of each entry in the list of source
instances, when agnClkSrcPortSrcIdx=master(1)or fallback(2).
According to this type, agnClkSrcPort gets the relevant meaning (Port index
or Recover…

Enumerationr/w

Enumerated Values:

1	noScramble
2	rxTxScramble
3	rxOnlyScramble
4	txOnlyScramble

.1.3.6.1.4.1.164.6.2.52.1.1.11

agnCurrClkTable

table

.1.3.6.1.4.1.164.6.2.52.2 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnCurrClkTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnCurrClkTable'

Current Clock Source.

agnCurrClkEntry row .1.3.6.1.4.1.164.6.2.52.2.1

An entry in the table.

Indexes

No indexes recorded

Column	Syntax	OID
agnCurrClkObjIdx This MIB object identifies the object for which the Clock Source is used (System, Other System, Card).	Integer32	`.1.3.6.1.4.1.164.6.2.52.2.1.1`
agnCurrClkMode Current Clock Source Mode. master - refers Master clock fallback - refers Fallback clock internal - only when both Master and Fallback Sources failed	Enumeration Constraints: `range: 1-255`	`.1.3.6.1.4.1.164.6.2.52.2.1.2`
agnCurrClkSrc This object indicates the Current Clock Source.	Enumeration	`.1.3.6.1.4.1.164.6.2.52.2.1.3`
agnCurrClkPort This object indicates the Port/Interface/Recovered ID that is Currently used as Clock Source. - When agnCurrClkSrc=rxClock(3), this object indicates a Port index. - When agnCurrClkSrc=recovered(12), this object indicat…	Integer32	`.1.3.6.1.4.1.164.6.2.52.2.1.4`
agnCurrClkHoldover Current Clock Holdover State. As a last resort, in the absence of higher quality timing: - a SONET/SDH object can enter 'holdover' state, until higher quality external timing becomes available again. In this state …	Enumeration	`.1.3.6.1.4.1.164.6.2.52.2.1.5`
agnCurrClkSsmBased This parameter indicates whether clock source is selected based on receive clock quality. Clock quality is indicated in S1 byte inside SONET/SDH overhead, (encoded as SSM - Synchronization Status Messaging).	Enumeration	`.1.3.6.1.4.1.164.6.2.52.2.1.6`
agnCurrClkState This object indicates the Current Clock State. freeRun(1) - Current clock state machine is not locked and run from the internal oscillator. rapidPhaseLock(2) - Current clock state machine i…	Enumeration	`.1.3.6.1.4.1.164.6.2.52.2.1.7`
agnCurrClkQualification This object indicates the Current Clock Qualification and defines whether the PLL can locked according to the stratum definitions.	Enumeration	`.1.3.6.1.4.1.164.6.2.52.2.1.8`

agnClkCurrentTable

table

.1.3.6.1.4.1.164.6.2.52.3.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnClkCurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnClkCurrentTable'

The Clock Current table.

agnClkCurrentEntry row .1.3.6.1.4.1.164.6.2.52.3.1.1

An entry in the Clock Current table.

Indexes

No indexes recorded

Column	Syntax	OID
agnClkCurrentIndex An Index that is uniquely represents the Clock.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.2.52.3.1.1.1`
agnClkCurrentRxPackets The counter associated with the number of Received Packets, encountered by a Bridge Port in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.2.52.3.1.1.2`
agnClkCurrentLostPackets The counter associated with the number of Lost Packets, encountered by a Bridge Port in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.2.52.3.1.1.3`
agnClkCurrentOutOfOrderPackets The counter associated with the number of times Out-of-Order Packets encountered by a Bridge Port in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.2.52.3.1.1.4`
agnClkCurrentBufferUnderflow The counter associated with the number of times Underflow event encountered by a Bridge Port in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.2.52.3.1.1.5`

agnClkIntervalTable

table

.1.3.6.1.4.1.164.6.2.52.3.2 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnClkIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnClkIntervalTable'

The Clock Interval table.

agnClkIntervalEntry row .1.3.6.1.4.1.164.6.2.52.3.2.1

An entry in the Clock Interval table.

Indexes

No indexes recorded

Column	Syntax	OID
agnClkIntervalIndex An Index that is uniquely represents the Clock.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.2.52.3.2.1.1`
agnClkIntervalNumber A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals exist).	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.2.52.3.2.1.2`
agnClkIntervalRxPackets The counter associated with the number of Received Packets, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.2.52.3.2.1.3`
agnClkIntervalLostPackets The counter associated with the number of Lost Packets, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.2.52.3.2.1.4`
agnClkIntervalOutOfOrderPackets The counter associated with the number of times Out-of-Order Packets are detected, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.2.52.3.2.1.5`
agnClkIntervalBufferUnderflow The counter associated with the number of times Underflow event is detected, encountered by a Bridge Port in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.2.52.3.2.1.6`

lagTable

table

.1.3.6.1.4.1.164.6.2.54.1 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk lagTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::lagTable'

A table defining Link Aggregation Groups port association, 
and other parameters.

lagEntry row .1.3.6.1.4.1.164.6.2.54.1.1

An entry in the LAG table.

Indexes

No indexes recorded

Column Syntax OID

lagCnfgIdx

This object indicates the Idx of the Cnfg(1..255) being
accessed ; Idx of 255 relates to the TmpCnfg.

Unsigned32

.1.3.6.1.4.1.164.6.2.54.1.1.1

lagIdx

This object indicates LAG unique index.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.54.1.1.2

lagPortMembers

The set of ports which are permanently assigned to the
Link Aggregation Group.
The default value of this object is a string of zeros.

Q-BRIDGE-MIBPortListr/w

.1.3.6.1.4.1.164.6.2.54.1.1.3

lagDistributionMethod

This object defines the criteria for the 802.3ad (LAG)
to split the traffic between ports

Enumerationr/w

Constraints:
range: 0-100

.1.3.6.1.4.1.164.6.2.54.1.1.4

lagRecoveryMode

This object defines whether traffic will be returned to
a port after its recovery.
This object is applicable only when
lagDistributionMethod= oneToOne (3).

Enumerationr/w

Enumerated Values:

2	disable
3	enable

.1.3.6.1.4.1.164.6.2.54.1.1.5

lagWaitToRestore

This object defines traffic recovery time (in seconds)
to the port after its recovery.
This object is applicable only when
lagRecoveryMode= revertive (3).

Unsigned32r/w

.1.3.6.1.4.1.164.6.2.54.1.1.6

lagRowStatus

This object enables user to create/delete
entries of this table.
Note:
When using LAG standard package, this table is static,
hence, only the values active(1), notInService(2) are used.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.6.2.54.1.1.7

lagShutDownDurationUponFlip

This object defines the duration (in seconds) the active
port transmission is shut down after LAG Flip occurs.
The transmission is shut down and then opened again (after the duration
defined by this object), in ord…

Unsigned32r/w

.1.3.6.1.4.1.164.6.2.54.1.1.8

lagRdnMethod

This object defines the redundancy method.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.54.1.1.9

lagLacpEnable

Enabling/Disabling the LACP for a LAG.
The LACP will be enabled for all ports belonging to this LAG.

Enumerationr/w

Constraints:
range: 1-2147483647

.1.3.6.1.4.1.164.6.2.54.1.1.10

lagStatTable

table

.1.3.6.1.4.1.164.6.2.54.2 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk lagStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::lagStatTable'

A table defining Link Aggregation Groups Redundancy. This table is applicable only 
when lagDistributionMethod = oneToOne.

lagStatEntry row .1.3.6.1.4.1.164.6.2.54.2.1

An entry in the LAG Status table.

Indexes

No indexes recorded

Column	Syntax	OID
lagStatForcePort This object enables user to enforce the active port. 0 = No Enforcement; Otherwise the ifIndex of the port.	SNMPv2-SMIUnsigned32r/w Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.2.54.2.1.1`
lagStatActivePort This object indicates the current active port. It is applicable only when lagDistributionMethod = oneToOne. The value is the ifIndex of the port. 0 = none of the ports is active.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.2.54.2.1.2`

gfpCnfgTable

table

.1.3.6.1.4.1.164.6.2.55.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk gfpCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::gfpCnfgTable'

Configuration table for GFP (General Framing Protocol).

gfpCnfgEntry row .1.3.6.1.4.1.164.6.2.55.1.1

An entry in the GFP configuration table.

Indexes

No indexes recorded

Column Syntax OID

gfpCnfgIdx

Index to GFP configuration table.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.55.1.1.1

gfpPayloadFcs

This object defines whether protocol header will
include FCS.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.55.1.1.2

gfpRxTxScramble

This object defines whether transmission will be scrambled.

Enumerationr/w

.1.3.6.1.4.1.164.6.2.55.1.1.3

gfpVcatHeader

VCAT header is LCAS CONTROL packet as described in the G-7043.
one control packet is transmitted in a period of 16 Multi frame

Enumerationr/w

Enumerated Values:

1	active
4	createAndGo
6	destroy

.1.3.6.1.4.1.164.6.2.55.1.1.4

agnGroupTable

table

.1.3.6.1.4.1.164.6.2.56 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnGroupTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnGroupTable'

A table that enables associating components to Group/s
(or removing components of a group).
The Group Idx can then be used in other tables (e.g alarmForwardingTable).

agnGroupEntry row .1.3.6.1.4.1.164.6.2.56.1

An entry in the agnGroupTable.

Indexes

prtPriorityIdx1 prtPriorityPrtIdx prtPriorityIdx

Column Syntax OID

agnGroupCnfgIdx

This object indicates the Idx of the Cnfg(1..255) being
accessed ; Idx of 255 relates to the TmpCnfg.

Unsigned32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.6.2.56.1.1

agnGroupIdx

This object indicates a unique Group Index.

SNMPv2-SMIUnsigned32

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.164.6.2.56.1.2

agnGroupComponentIdx

This object indicates a unique Component Index that belongs to the
Group defined by agnGroupIdx.

SNMPv2-SMIUnsigned32

Constraints:
range: 0-7

.1.3.6.1.4.1.164.6.2.56.1.3

agnGroupRowStatus

This object enables user to create/delete entries of this table.
destroy - If a Group is used in another table, Agent may not allow
destroying the entry/ies that belong to this Group Index.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.6.2.56.1.4

alarmSyncTable

table

.1.3.6.1.4.1.164.6.2.61.2.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk alarmSyncTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::alarmSyncTable'

This table includes Alarm Synchronization information
for each Logical Group of managers.

alarmSyncEntry row .1.3.6.1.4.1.164.6.2.61.2.1.1

An entry in the table.

Indexes

prtQosIdx prtQosPrtIdx prtQosDirection

Column Syntax OID

alarmSyncGroupId

A unique Logical Group ID,
which represents a group of managers.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.61.2.1.1.1

alarmSyncLastSentSeqId

Last Sequence ID of trap that is sent
to this Logical Group of managers.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.61.2.1.1.2

alarmSyncCmd

Initates an Alarm Synchronization request
for this Logical Group of managers.

softSync(2) - sends Soft Synchronization request,
in order to synchronize missing traps from Agent.
hardSync(3) - sends …

Enumerationr/w

Enumerated Values:

1	all
2	ingress
3	egress

.1.3.6.1.4.1.164.6.2.61.2.1.1.3

alarmSyncStartSeqId

First Sequence ID of Soft Synchronization request
for this Logical Group of managers.

Soft Synchronization request is sent for a range of Sequence IDs.
This object represents the first Sequence ID of this…

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	all
2	bcastAndMcastAndFloodedUcast
3	bcastAndMcast
4	bcast

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.61.2.1.1.4

alarmSyncEndSeqId

Last Sequence ID of Soft Synchronization request
for this Logical Group of managers.

Soft Synchronization request is sent for a range of Sequence IDs.
This object represents the last Sequence ID of this r…

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.2.61.2.1.1.5

agnStringToIndexTable

table

.1.3.6.1.4.1.164.6.2.62 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnStringToIndexTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnStringToIndexTable'

This table holds the conversions of tables from unique String 
to numeric index.

agnStringToIndexEntry row .1.3.6.1.4.1.164.6.2.62.1

An entry in the table.

Indexes

No indexes recorded

Column	Syntax	OID
agnStringToIndexTableId The OBJECT IDENTIFIER of the Table, having as index numeric values. In this table, the value of agnStringToIndexUserName is an attribute.	ObjectIdentifier	`.1.3.6.1.4.1.164.6.2.62.1.1`
agnStringToIndexUserName This object indicates a unique name used by agnStringToIndexTableId, although it is not it's index.	OctetString	`.1.3.6.1.4.1.164.6.2.62.1.2`
agnStringToIndexTableIndex The numeric Index of agnStringToIndexTableId.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.2.62.1.3`

agnRowPointerTable

table

.1.3.6.1.4.1.164.6.2.63 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk agnRowPointerTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::agnRowPointerTable'

This table holds information about a specific entry in a table.
For example, number of usages of this row.

agnRowPointerEntry row .1.3.6.1.4.1.164.6.2.63.1

An entry in the table.

Indexes

No indexes recorded

Column	Syntax	OID
agnRowPointerIndex The OBJECT IDENTIFIER of an entry in a table.	ObjectIdentifier Constraints: `range: 0-7`	`.1.3.6.1.4.1.164.6.2.63.1.1`
agnRowPointerNoOfUsages The number of usages of specific entry in a table, which is pointed by agnRowPointerIndex.Usually, when the value of this counter is greater than 0,the entry cannot be removed.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.2.63.1.2`

wfqTable

table

.1.3.6.1.4.1.164.6.3.1.1 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk wfqTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::wfqTable'

This table allows user to define several
WFQ tables per output port.
          
WFQ supports flows with different bandwidth requirements 
by giving each queue a weight that assigns it 
a different percentage of output port bandwidth.
          
When Weighted Fair Queuing is used, 
it is possible to precisely attribute bandwidth 
partitioning among the queues. 
When there is congestion, each class (queue) 
is not allowed to use more bandwidth than the amount 
allocated to it.

wfqEntry row .1.3.6.1.4.1.164.6.3.1.1.1

An entry in the Weighted Fair Queueing table.

Indexes

No indexes recorded

Column Syntax OID

wfqCnfgIdx

This object indicates the Idx of the Agent Cnfg the following
objects refer.
255=Temporary Cnfg (when relevant,
Set is done only to this configuration).
For Agents that support only one configuration,
this object wil…

Integer32

Constraints:
range: 0-7

.1.3.6.1.4.1.164.6.3.1.1.1.1

wfqPrtIdx

This object indicates a unique port or interface number,
for which Weighted Fair Queueing table is applicable .
For numbering, see product's spec.
For some products, the numbering can equal ifIndex.
Value of 255 (not …

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.3.1.1.1.2

wfqTblIdx

This object indicates which Weighted Fair Queueing (WFQ)
Table is being used. There can be several tables.
For FCD-155 User will select which one will be used
for a virtual concatenation group.Valid values are 1,2

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.3.1.1.1.3

wfqQueueIdx

This object indicates a queue index.
For FCD-155, valid queues are 1..3.
The 4th queue is not in MIB.
Its weight will be RO, Calculated according to
the sum of the 3 first queues.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.3.1.1.1.4

wfqRowStatus

This object enables Creation/Deletion of
rows in the WFQ table.
For FCD-155, rows are not created nor destroyed by user.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.6.3.1.1.1.5

wfqWeightValue

This object indicates a relative weight value.
User should make sure that the sum of
values for all queues will not exceed 100%
(sum should be BELOW 100% in order
to leave some BW percentage for last queue)
Note th…

%Integer32r/w

.1.3.6.1.4.1.164.6.3.1.1.1.6

wfqSchedulingMode

This object controls which scheduling mode is used:
Weighted Fair Queuing (WFQ) scheme or priority Queue (Strict Priority).

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.6.3.1.1.1.7

wfqMinRateAbsolute

The minimum absolute rate, in kbps,
that should be allocated to this queue.
If the value is zero, then there is effectively
no minimum rate guarantee.
If the value is non-zero, then the servicing of
this queue in at…

KbpsSNMPv2-SMIUnsigned32r/w

Constraints:
range: 1-4095

.1.3.6.1.4.1.164.6.3.1.1.1.8

wfqMaxPacketSize

The size of the largest packet which can be received
on this queue, specified in octets.
Packets larger than this size will be discarded.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.1.1.1.9

dscpMappingTable

table

.1.3.6.1.4.1.164.6.3.2.1 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk dscpMappingTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::dscpMappingTable'

Mapping of DSCP value to a regenerated priority level.

dscpMappingEntry row .1.3.6.1.4.1.164.6.3.2.1.1

An entry in dscpMappingTable.

Indexes

No indexes recorded

Column Syntax OID

dscpMappingCnfgIdx

This object indicates the Idx of the Agent Cnfg the following
objects refer to.
255=Temporary Cnfg (when relevant, Set is done only
to this configuration).
For Agents that support only one configuration,
this object …

Integer32

.1.3.6.1.4.1.164.6.3.2.1.1.1

dscpMappingDscpIdx

DSCP value of the incoming IP packet

Dscp

Type Constraints:
range: 0..63

.1.3.6.1.4.1.164.6.3.2.1.1.2

dscpMappingRegenPriority

The Regenerated Priority level the
incoming DSCP value is mapped to.
For FCD-155, valid values are 0,1,2,3

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	upstream
2	downstream

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.6.3.2.1.1.3

ifTeQosTable

table

.1.3.6.1.4.1.164.6.3.3.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ifTeQosTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ifTeQosTable'

The TE QOS Interface Table.

ifTeQosEntry row .1.3.6.1.4.1.164.6.3.3.1.1

An entry in the TE QOS Interface table.

Indexes

No indexes recorded

Column	Syntax	OID
ifTeQosIdx1 This object indicates the 1st Index of the table.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.6.3.3.1.1.1`
ifTeQosIdx2 This object indicates the 2nd Index of the table.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.6.3.3.1.1.2`
ifTeQosIdx3 This object indicates the 3rd Index of the table.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.6.3.3.1.1.3`
ifTeQosParam This object is used for QOS attributes of the entry's entities.	OctetStringr/w	`.1.3.6.1.4.1.164.6.3.3.1.1.4`
ifTeQosParam2 This object is used for 2nd group QOS attributes of the entry's entities.	OctetStringr/w	`.1.3.6.1.4.1.164.6.3.3.1.1.5`
ifTeQosStatus This object is used to create, activate and destroy entries of this table.	Enumerationr/w	`.1.3.6.1.4.1.164.6.3.3.1.1.6`

prtPriorityTable

table

.1.3.6.1.4.1.164.6.3.4.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtPriorityTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtPriorityTable'

A table - Parameters per port per Priority .

prtPriorityEntry row .1.3.6.1.4.1.164.6.3.4.1.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
prtPriorityIdx1 This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg. or any other Index.	Integer32	`.1.3.6.1.4.1.164.6.3.4.1.1.1`
prtPriorityPrtIdx This object indicates a unique Port Index. Refer to device specification for port Index.	Integer32	`.1.3.6.1.4.1.164.6.3.4.1.1.2`
prtPriorityIdx This object indicates the Traffic Priority Index.	Integer32	`.1.3.6.1.4.1.164.6.3.4.1.1.3`
prtPriorityIngressRateLimit The maximum rate permitted at Ingress of this port with this Traffic Priority, in Kbps.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.6.3.4.1.1.4`

prtQosTable

table

.1.3.6.1.4.1.164.6.3.4.2 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk prtQosTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::prtQosTable'

Port QoS (Quality of Service) table.

prtQosEntry row .1.3.6.1.4.1.164.6.3.4.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

prtQosIdx

The first index of the table.
This attribute might indicate the Idx of the Cnfg (1..255) being
accessed ; Idx of 255 relates to the TmpCnfg or any other Index.

SNMPv2-SMIUnsigned32

Enumerated Values:

2	off
3	on

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.4.2.1.1

prtQosPrtIdx

This object indicates a unique Port Index.
Refer to device specification for port Index.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.4.2.1.2

prtQosDirection

This object indicates the port's QoS Direction.

Enumeration

.1.3.6.1.4.1.164.6.3.4.2.1.3

prtQosRateLimitPacketType

This object indicates the Type of Packets on which Rate Limitation is applied.

Enumerationr/w

.1.3.6.1.4.1.164.6.3.4.2.1.4

prtQosRateLimitCIR

This object indicates the port's CIR (Committed Information Rate) in Kbps.
Value=0 represents best effort.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.4.2.1.5

prtQosRateLimitCBS

This object indicates the port's CBS (Committed Burst Size) in KB.
Value=0 represents best effort.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.4.2.1.6

prtQosRateLimitEIR

This object indicates the port's EIR (Excess Information Rate) in Kbps.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.4.2.1.7

prtQosRateLimitEBS

This object indicates the port's EBS (Excess Burst Size) in KB.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.4.2.1.8

portTrafficClassTable

table

.1.3.6.1.4.1.164.6.3.5.1 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk portTrafficClassTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::portTrafficClassTable'

Mapping of port to Traffic Class level.

portTrafficClassEntry row .1.3.6.1.4.1.164.6.3.5.1.1

An entry in portTrafficClassTable.

Indexes

No indexes recorded

Column	Syntax	OID
portTrafficClassIdx1 This attribute indicates the 1st index of the table. This may be the Idx of the Cnfg(1..255) being accessed; Idx of 255 relates to the TmpCnfg, or any other Index.	Integer32	`.1.3.6.1.4.1.164.6.3.5.1.1.1`
portTrafficClassPortIdx This object indicates a unique Port Index. Refer to device specification for port Index.	Integer32	`.1.3.6.1.4.1.164.6.3.5.1.1.2`
portTrafficClass This object indicates the Traffic Class level of this port.	Integer32r/w	`.1.3.6.1.4.1.164.6.3.5.1.1.3`

serviceTable

table

.1.3.6.1.4.1.164.6.3.6 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk serviceTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::serviceTable'

Table of services.

serviceEntry row .1.3.6.1.4.1.164.6.3.6.1

An entry in the Service Table.

Indexes

No indexes recorded

Column Syntax OID

flowIndex

Defines the Flow ID the service is associated to.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.6.1.1

serviceIndex

Defines the Service ID - according to the CoS.

Unsigned32

.1.3.6.1.4.1.164.6.3.6.1.2

serviceRowStatus

This attribute is used to create a new row or to delete an existing row
in the table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.6.3.6.1.3

serviceName

This attribute defines the service name.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.6.3.6.1.4

serviceBwProfileId

This variable holds the index of the Ingress BW profile assigned
to that service.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.6.1.5

evcCosTable

table

.1.3.6.1.4.1.164.6.3.7 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk evcCosTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::evcCosTable'

This table defines  mapping of Ethernet Virtual Connection 
(EVC) ID to Class of Service (CoS) ID

evcCosEntry row .1.3.6.1.4.1.164.6.3.7.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

evcCosCnfgIdx

This attribute indicates the Idx of the Cnfg(1..255) being
accessed ; Idx of 255 relates to the TmpCnfg.

Unsigned32

.1.3.6.1.4.1.164.6.3.7.1.1

evcCosEvcIdx

This attribute indicates EVC Id.

Unsigned32

Enumerated Values:

0	ieee802dot1p
1	tos
2	dscp
3	vlanId
4	macSrcAddr
5	macDestAddr
6	ipSrcAddr
7	ipDestAddr
8	tcpSrcPort
9	tcpDestPort
10	udpSrcPort
11	udpDestPort
12	ipPrecedence
13	innerIeee802dot1p
14	innerVlanId
15	untagged
16	nonIP
17	etherType

.1.3.6.1.4.1.164.6.3.7.1.2

evcCosRowStatus

This attribute allows to create/delete a row in this table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.6.3.7.1.3

evcCosEvcName

A string that identifies the EVC. It should be unique
in the Maintenance Domain (i.e., in the managed network)
Used as MEG ID field in OAM messages.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.6.3.7.1.5

evcCosSpVlanId

This object indicates the SP (Service Provider) VLAN used when sending
an OAM message for the specified EVC.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.7.1.6

serviceStatTable

table

.1.3.6.1.4.1.164.6.3.8 · 1 row entry · 26 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk serviceStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::serviceStatTable'

Service statistics table.

serviceStatEntry row .1.3.6.1.4.1.164.6.3.8.1

An entry in the Service Statistics Table.

Indexes

No indexes recorded

Column	Syntax	OID
serviceStatDirection The direction in wich the measurement is taken.	Enumeration	`.1.3.6.1.4.1.164.6.3.8.1.1`
srvForwardGreenPackets This attribute displays the counted number of forwarded packets that where marked Green.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.2`
srvForwardGreenPacktesOverflow This attribute displays the number of times that the forwardGreenPackets counter has overflowed.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.3`
srvForwardYellowPackets This attribute displays the counted number of forwarded packets that where marked Yellow.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.4`
srvForwardYellowPacketsOverflow This attribute displays the number of times that the forwardYellowPackets counter has overflowed.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.5`
srvDiscardGreenPacket This attribute displays the counted number of discarded packets that where marked Green.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.6`
srvDiscardGreenPacketOverflow This attribute displays the number of times that the discardGreenPacket counter has overflowed.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.7`
srvDiscardYellowRedPackets This attribute displays the counted number of discarded packets that where marked Yellow or Red.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.8`
srvDiscardYellowRedPacketsOverflow This attribute displays the number of times that the discardYellowRedPackets counter has overflowed.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.9`
srvForwardGreenBytes This attribute displays the counted number of forwarded bytes that where marked Green.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.10`
srvForwardGreenBytesOverflow This attribute displays the number of times that the forwardGreenBytes counter has overflowed.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.11`
srvForwardYellowBytes This attribute displays the counted number of forwarded bytes that where marked Yellow.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.12`
srvForwardYellowBytesOverflow This attribute displays the number of times that the forwardYellowBytes counter has overflowed.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.13`
srvDiscardGreenBytes This attribute displays the counted number of discarded bytes that where marked Green.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.14`
srvDiscardGreenBytesOverflow This attribute displays the number of times that the discardGreenBytes counter has overflowed.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.15`
srvDiscardYellowRedBytes This attribute displays the counted number of discarded bytes that where marked Yellow or Red.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.16`
srvDiscardYellowRedBytesOverflow This attribute displays the number of times that the discardYellowRedBytes counter has overflowed.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.17`
srvResetStatsCmd Reset statistic counters of the service.	Enumerationr/w	`.1.3.6.1.4.1.164.6.3.8.1.18`
srvDiscardYellowPackets This attribute displays the counted number of discarded packets that where marked Yellow.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.19`
srvDiscardYellowPacketsOverflow This attribute displays the number of times that the discardYellowPackets counter has overflowed.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.20`
srvDiscardYellowBytes This attribute displays the counted number of discarded bytes that where marked Yellow.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.21`
srvDiscardYellowBytesOverflow This attribute displays the number of times that the discardYellowBytes counter has overflowed.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.22`
srvDiscardRedPackets This attribute displays the counted number of discarded packets that where marked Red.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.23`
srvDiscardRedPacketsOverflow This attribute displays the number of times that the discardRedPackets counter has overflowed.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.24`
srvDiscardRedBytes This attribute displays the counted number of discarded bytes that where marked Red.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.25`
srvDiscardRedBytesOverflow This attribute displays the number of times that the discardRedBytes counter has overflowed.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.6.3.8.1.26`

flowMappingProfileTable

table

.1.3.6.1.4.1.164.6.3.9.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk flowMappingProfileTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::flowMappingProfileTable'

This table holds flow mapping profiles.

flowMappingProfileEntry row .1.3.6.1.4.1.164.6.3.9.1.1

Each entry in this table describes one Flow mapping profile with
one of its Flow Mapping supported, according to the Priority order.
The information includes a reference to a Flow Mapping index.

Indexes

No indexes recorded

Column Syntax OID

flowMappingProfileIndex

A running index for the Flow Mapping Profile table.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.1.1.1

flowMappingProfilePriority

The priority of the Mapping selected by flowMappingProfileMapIndex
within the Flow Mapping Profile.

SNMPv2-SMIInteger32

Constraints:
range: 0-63

.1.3.6.1.4.1.164.6.3.9.1.1.2

flowMappingProfileRowStatus

This attribute is used to create a new row or to delete an existing row
in the table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.6.3.9.1.1.3

flowMappingProfileNumOfMaps

This attribute determines the number of the mappings
associated to the Flow Mapping Profile.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.1.1.4

flowMappingProfileMapIndex

This attribute holds a reference to the mapping index.
It specifies the mapping selected for the Mapping Profile
for the selected Priority.
When flowMappingProfileNumOfMaps=0, this attribute is not relevant.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.1.1.5

flowMappingProfileName

This attribute defines the name assigned to flowMappingIndex profile.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.6.3.9.1.1.6

qosFlowMappingTable

table

.1.3.6.1.4.1.164.6.3.9.2 · 1 row entry · 33 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk qosFlowMappingTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::qosFlowMappingTable'

A table of Flow Mapping.

qosFlowMappingEntry row .1.3.6.1.4.1.164.6.3.9.2.1

Each entry in this table describes one Flow Mapping.
The information includes combination (AND function) of all the
classifications, as defined in the qosFlowMappingCriteria field.
Classifiers are: TOS, DSCP, VLAN ID, …

Indexes

No indexes recorded

Column Syntax OID

qosFlowMappingIdx1

- In case the table is accessed via flowMappingProfileTable
this is a running index for the QoS Flow Mapping table.
- In case the table is not accessed via flowMappingProfileTable,
this will be the ifIndex of the XNI …

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.2.1.1

qosFlowMappingIdx2

An index for the QoS Flow Mapping table.
- In case the table is accessed via flowMappingProfileTable
the index will be fixed = 1.
- In case the table is not accessed via flowMappingProfileTable,
this will be the index o…

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.2.1.2

qosFlowMappingIdx3

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.2.1.3

qosFlowMappingRowStatus

This attribute is used to create a new row or to delete an existing row
in the table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.6.3.9.2.1.4

qosFlowMappingCriteria

This attribute determines upon which criterion the flow
will be mapped.

Bitsr/w

.1.3.6.1.4.1.164.6.3.9.2.1.5

qosFlowMappingIeee802dot1p

This attribute determines which TOS values are applicable for that flow.
Each bit (0..7) represents a different 802.1 P-bit value.
Setting '1' to the bit means that the corresponding 802.1 P-bit value is applicable.
It…

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	wfq
2	strict
3	bestEffort

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.2.1.6

qosFlowMappingTos

This attribute determines which TOS values are applicable for that flow.
Each bit (0..7) represents a different TOS value.
Setting '1' to the bit means that the corresponding TOS value is applicable.
It is relevant onl…

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.2.1.7

qosFlowMappingFromDscp

This attribute determines the first DSCP value to compare with in a range.
It is relevant only in case the dscp bit (2) in qosFlowMappingCriteria equals 1.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.2.1.8

qosFlowMappingToDscp

This attribute determines the first DSCP value to compare with in a range.
It is relevant only in case the dscp bit (2) in qosFlowMappingCriteria equals 1.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.2.1.9

qosFlowMappingFromVlanId

This attribute determines the first VLAN ID value to compare with in a range.
It is relevant only in case the vlanId bit (3) in qosFlowMappingCriteria equals 1.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.2.1.10

qosFlowMappingToVlanId

This attribute determines the last VLAN ID value to compare with in a range.
It is relevant only in case the vlanId bit (3) in qosFlowMappingCriteria equals 1.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.2.1.11

qosFlowMappingFromSrcMacAddr

This attribute determines the first source MAC address to compare with in a range.
It is relevant only in case the macSrcAddr bit (4) in qosFlowMappingCriteria equals 1.

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.6.3.9.2.1.12

qosFlowMappingToSrcMacAddr

This attribute determines the last source MAC address to compare with in a range.
It is relevant only in case the macSrcAddr bit (4) in qosFlowMappingCriteria equals 1.

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.6.3.9.2.1.13

qosFlowMappingFromDestMacAddr

This attribute determines the first destination MAC address to compare with in a range.
It is relevant only in case the macDestAddr (5) bit in qosFlowMappingCriteria equals 1.

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.6.3.9.2.1.14

qosFlowMappingToDestMacAddr

This attribute determines the last destination MAC address to compare with in a range.
It is relevant only in case the macDestAddr (5) bit in qosFlowMappingCriteria equals 1.

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.6.3.9.2.1.15

qosFlowMappingFromSrcIpAddr

This attribute determines the first source IP address to compare with in a range.
It is relevant only in case the ipSrcAddr (6) bit in qosFlowMappingCriteria equals 1.

RFC1155-SMIIpAddressr/w

Constraints:
range: 1-32

.1.3.6.1.4.1.164.6.3.9.2.1.16

qosFlowMappingToSrcIpAddr

This attribute determines the last source IP address to compare with in a range.
It is relevant only in case the ipSrcAddr (6) bit in qosFlowMappingCriteria equals 1.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.6.3.9.2.1.17

qosFlowMappingFromDestIpAddr

This attribute determines the first destination IP address to compare with in a range.
It is relevant only in case the ipDestAddr (7) bit in qosFlowMappingCriteria equals 1.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.6.3.9.2.1.18

qosFlowMappingToDestIpAddr

This attribute determines the last destination IP address to compare with in a range.
It is relevant only in case the ipDestAddr (7) bit in qosFlowMappingCriteria equals 1.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.6.3.9.2.1.19

qosFlowMappingFromTcpSrcPort

This attribute determines the first TCP source port to compare with in a range.
It is relevant only in case the tcpSrcPort bit (8) in qosFlowMappingCriteria equals 1.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.2.1.20

qosFlowMappingToTcpSrcPort

This attribute determines the last TCP source port to compare with in a range.
It is relevant only in case the tcpSrcPort bit (8) in qosFlowMappingCriteria equals 1.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.2.1.21

qosFlowMappingFromTcpDestPort

This attribute determines the first TCP destination port to compare with in a range.
It is relevant only in case the tcpDestPort bit (9) in qosFlowMappingCriteria equals 1.

SNMPv2-SMIUnsigned32r/w

Constraints:
range: 1-32

.1.3.6.1.4.1.164.6.3.9.2.1.22

qosFlowMappingToTcpDestPort

This attribute determines the last TCP destination port to compare with in a range.
It is relevant only in case the tcpDestPort bit (9) in qosFlowMappingCriteria equals 1.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.2.1.23

qosFlowMappingFromUdpSrcPort

This attribute determines the first UDP source port to compare with in a range.
It is relevant only in case the udpSrcPort bit (10) in qosFlowMappingCriteria equals 1.

SNMPv2-SMIUnsigned32r/w

Constraints:
range: 1-32

.1.3.6.1.4.1.164.6.3.9.2.1.24

qosFlowMappingToUdpSrcPort

This attribute determines the last UDP source port to compare with in a range.
It is relevant only in case the udpSrcPort bit (10) in qosFlowMappingCriteria equals 1.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.2.1.25

qosFlowMappingFromUdpDestPort

This attribute determines the first UDP destination port to compare with in a range.
It is relevant only in case the udpDestPort bit (11) in qosFlowMappingCriteria equals 1.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.2.1.26

qosFlowMappingToUdpDestPort

This attribute determines the last UDP destination port to compare with in a range.
It is relevant only in case the udpDestPort bit (11) in qosFlowMappingCriteria equals 1.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.2.1.27

qosFlowMappingFromIpPrecedence

This attribute determines the first IpPrecedence value to compare with in a range.
It is relevant only in case the IpPrecedence bit (12) in qosFlowMappingCriteria equals 1.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.2.1.28

qosFlowMappingToIpPrecedence

This attribute determines the last IpPrecedence value to compare with in a range.
It is relevant only in case the IpPrecedence bit (12) in qosFlowMappingCriteria equals 1.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.2.1.29

qosFlowMappingInnerIeee802dot1p

This attribute determines which TOS values are applicable for that flow.
Each bit (0..7) represents a different inner 802.1 P-bit value.
Setting '1' to the bit means that the corresponding inner 802.1 P-bit value is ap…

SNMPv2-SMIUnsigned32r/w

Constraints:
range: 0-63

.1.3.6.1.4.1.164.6.3.9.2.1.30

qosFlowMappingFromInnerVlanId

This attribute determines the first inner VLAN ID value to compare with in a range.
It is relevant only in case the innerVlanId bit(14) in qosFlowMappingCriteria equals 1.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

2	ieee802dot1p
3	tos
4	dscp
5	ipPrecedence

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.2.1.31

qosFlowMappingToInnerVlanId

This attribute determines the last inner VLAN ID value to compare with in a range.
It is relevant only in case the innerVlanId bit(14) in qosFlowMappingCriteria equals 1.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.2.1.32

qosFlowMappingEtherType

Determines the Tag Protocol Identifier (in Hex).
For example:
0x8100 (C-TAG)
0x88A8 (S-TAG)
It is relevant only in case the etherType bit (17) in qosFlowMappingCriteria equals 1.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.9.2.1.33

cosProfileTable

table

.1.3.6.1.4.1.164.6.3.10 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk cosProfileTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::cosProfileTable'

Class of Service Profile table. 
Each profile holds a priority method, and a mappring function 
that maps the priority values (range according to the method) 
into CoS values.

cosProfileEntry row .1.3.6.1.4.1.164.6.3.10.1

A conceptual row where each row contains one CoS attributes.

Indexes

No indexes recorded

Column Syntax OID

cosProfileIndex

Defines the CoS Profile ID.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.10.1.1

cosProfileRowStatus

This attribute is used to create a new row or to delete an existing row
in the table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.6.3.10.1.2

cosProfileCosMethod

Defines the priority method upon CoS mapping is done.

Enumerationr/w

.1.3.6.1.4.1.164.6.3.10.1.3

cosProfileName

This attribute defines the name assigned to CoS profile.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.6.3.10.1.4

cosProfileCosMapping

This attribute defines the value of the CoS that is assigned
for each priority. The number of the valid octets depends upon
the priority method selected:
Octet 0 corresponds to priority = 0
Octet 1 corresponds to pri…

OctetStringr/w

.1.3.6.1.4.1.164.6.3.10.1.5

qProfileTable

table

.1.3.6.1.4.1.164.6.3.11.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk qProfileTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::qProfileTable'

This table defines the profiles for a cluster of queues.

qProfileEntry row .1.3.6.1.4.1.164.6.3.11.1.1

A conceptual row where each row contains one Queue Cluster attribute.

Indexes

No indexes recorded

Column Syntax OID

qProfileIndex

Defines the Queue Cluster Profile ID.

SNMPv2-SMIUnsigned32

Enumerated Values:

1	unknown
2	off
3	on

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.11.1.1.1

qProfileRowStatus

This attribute is used to create a new row or to delete an existing row
in the table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.6.3.11.1.1.2

qProfileName

This attribute holds the name of the Queue cluster profile.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.6.3.11.1.1.3

qProfileNumberOfInternalQ

This attribute holds the number of the internal queue profiles
that are pointed by qInternalQProfile.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.11.1.1.4

qProfileInternalQProfile

This attribute holds the indexes to the queue profiles
in the qInternalProfileTable.
Each couple of octets holds an index to the qInternalProfileTable.

OctetStringr/w

.1.3.6.1.4.1.164.6.3.11.1.1.5

qInternalProfileTable

table

.1.3.6.1.4.1.164.6.3.11.2 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk qInternalProfileTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::qInternalProfileTable'

This table holds queue profiles.

qInternalProfileEntry row .1.3.6.1.4.1.164.6.3.11.2.1

A conceptual row where each row contains one Queue attribute.

Indexes

No indexes recorded

Column Syntax OID

qInternalProfileIndex

Defines the Queue Profile ID.

SNMPv2-SMIUnsigned32

Enumerated Values:

1	unknown
2	off
3	on

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.11.2.1.1

qInternalProfileRowStatus

This attribute is used to create a new row or to delete an existing row
in the table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.6.3.11.2.1.2

qInternalProfileScheduling

This attribute determines the queue scheduling method.

Enumerationr/w

Enumerated Values:

1	unknown
2	fourMegabit
3	sixteenMegabit

.1.3.6.1.4.1.164.6.3.11.2.1.3

qInternalProfileWFQWeight

This attribute determines the weight that each WFQ (Weighted Fair Queue)
participant gets.
It is applicable only when scheduling is configured to WFQ.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	unknown
2	disabled
3	enabled

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.11.2.1.4

qInternalProfileQueueLength

This attribute determines the length of the queue.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	unknown
2	off
3	on

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.11.2.1.5

qInternalProfileWredStartDropThresh

This attribute determines the length that the queue (Start Value)
must reach before the packets colored yellow will start being dropped
by the WRED (Weighted Random Early Detection/Discard) mechanism.
WRED is one the mo…

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.11.2.1.6

qInternalProfileWredDropAllThresh

This attribute determines the length that the queue (Stop Value)
must reach before the WRED (Weighted Random Early Detection)
shaper mechanism stops dropping randomly,
and just drops all further packets marked as yello…

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.11.2.1.7

qInternalProfileWredDropProbability

This attribute determines the percentage of packets that are being dropped
at the point when the length of the queue reaches the Stop value.
So, effectively, this defines how quickly the rate of dropping packet must
in…

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.11.2.1.8

qInternalProfileRateLimit

This attribute determines the Rate Limit of the queue in Kbps.
Value=0 represents best effort.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.11.2.1.9

qInternalProfileShaperProfile

This attribute defines the Shaper Profile (bwProfileIndex from bwProfileTable)
assigned to this qInternalProfile. Valid range of bwProfileIndex for Shaper
Profiles is 0x8000001-0x8000041.
If set to '0', no profile is a…

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.11.2.1.10

queueGroupTable

table

.1.3.6.1.4.1.164.6.3.11.3 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk queueGroupTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::queueGroupTable'

This table defines the queue groups/blocks,their level and connections between them.

queueGroupEntry row .1.3.6.1.4.1.164.6.3.11.3.1

A conceptual row where each row contains one Queue group.

Indexes

No indexes recorded

Column Syntax OID

queueGroupName

Defines the Queue Group unique name.

OctetString

Enumerated Values:

1	unknown
2	disable
3	enable
4	short
5	normal

.1.3.6.1.4.1.164.6.3.11.3.1.1

queueGroupQBlockLevel

This attribute holds the Level of the Queue Block .First level is 1.
NA=2^32-1.

SNMPv2-SMIUnsigned32

Enumerated Values:

1	unknown
2	off
3	on
4	standby

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.11.3.1.2

queueGroupQBlockIdx

This attribute holds the ID of the Queue Block.
NA=2^32-1.

SNMPv2-SMIUnsigned32

Enumerated Values:

2	off
3	on

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.11.3.1.3

queueGroupRowStatus

This attribute is used to create a new row or to delete an existing row
in the table.

SNMPv2-TCRowStatusr/w

Enumerated Values:

1	unknown
2	disabledManual
3	disabledAutorec
4	disabledSecurity
5	disabledAuto
6	disabledFlip
7	inserted
8	bypass
9	forcedloop
10	trunkfail
11	normal

Description:

.1.3.6.1.4.1.164.6.3.11.3.1.4

queueGroupQBlockProfile

This attribute defines the Queue profile assigned to this Queue Block.
This object points to qProfileIndex in qProfileTable.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	unknown
2	off
3	on
4	inhibit

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.11.3.1.5

queueGroupQBlockShaperProfile

This attribute defines the Shaper profile assigned to this Queue Block.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	unknown
2	off
3	on

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.11.3.1.6

queueGroupPointToQBlock

This attribute defines the Queue Block name of the next Queue Block level
that is pointed by this Queue Block.

OctetStringr/w

.1.3.6.1.4.1.164.6.3.11.3.1.7

queueGroupPointToInternalQueue

This attribute defines the internal queue whithin queueGroupPointToQBlock
that is pointed by this Queue Block.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	notApplicable
2	tfr
3	tfc
4	tcr
5	tcp

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.11.3.1.8

queueGroupQBlockName

This attribute holds the name of the Queue Block.

OctetStringr/w

.1.3.6.1.4.1.164.6.3.11.3.1.9

markingProfileTable

table

.1.3.6.1.4.1.164.6.3.12 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk markingProfileTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::markingProfileTable'

Marking profile table. Each profile holds a marking function 
which converts CoS values to Service Provider priority values.

markingProfileEntry row .1.3.6.1.4.1.164.6.3.12.1

A conceptual row where each row contains one Marking attribute.

Indexes

No indexes recorded

Column Syntax OID

markingProfileIndex

Defines the Marking Profile ID.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.6.3.12.1.1

markingProfileRowStatus

This attribute is used to create a new row or to delete an existing row
in the table.

SNMPv2-TCRowStatusr/w

Enumerated Values:

1	unknown
2	off
3	hwReset
4	configReset

Description:

.1.3.6.1.4.1.164.6.3.12.1.2

markingProfileName

This attribute defines the unique name assigned to the Marking profile.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.6.3.12.1.3

markingSpVlanPBit

For ETX-202A :
This attribute defines the value of the SP VLAN P-Bit that is assigned
for each CoS:
Octet 0 corresponds to CoS = 0
Octet 1 corresponds to CoS = 1
...
Octet 7 corresponds to CoS = 7.

For L…

OctetStringr/w

.1.3.6.1.4.1.164.6.3.12.1.4

markingProfileMethod

This attribute defines the method upon which marking is done.

Enumerationr/w

Constraints:
range: 1-2000

.1.3.6.1.4.1.164.6.3.12.1.5

stkHubSecurityTable

table

.1.3.6.1.4.1.164.7.1.2 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk stkHubSecurityTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::stkHubSecurityTable'

Hub's Security parameters.

stkHubSecurityEntry row .1.3.6.1.4.1.164.7.1.2.1

An entry in table stkHubSecurityTable.

Indexes

No indexes recorded

Column	Syntax	OID
stkHubSecID Segment's security unique identification number	Integer32	`.1.3.6.1.4.1.164.7.1.2.1.1`
stkHubSecEnable This entry indicates whether the specific segment's security is active or not	Enumerationr/w	`.1.3.6.1.4.1.164.7.1.2.1.2`
stkHubSecurityPattern A six-octet(48 bit) pattern: where the masked bits of stkHubSecurityMask need to match the MAC address of each port within the segment.Value of all zeros indicates no security.	OctetStringr/w	`.1.3.6.1.4.1.164.7.1.2.1.3`
stkHubSecurityMask Mask of the allowed MAC address that can be connected through the ports within the segment	OctetStringr/w	`.1.3.6.1.4.1.164.7.1.2.1.4`

stkHubPrtSecurityTable

table

.1.3.6.1.4.1.164.7.1.3 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk stkHubPrtSecurityTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::stkHubPrtSecurityTable'

Port Security parameters.

stkHubPrtSecurityEntry row .1.3.6.1.4.1.164.7.1.3.1

An entry in table stkHubPrtSecurityTable.

Indexes

No indexes recorded

Column Syntax OID

stkHubModuleID

A unique identifier of the module(slot no.)this port is attached to.

SNMPv2-SMIInteger32

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.7.1.3.1.1

stkHubPrtID

A unique identifier of the port within its module.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.7.1.3.1.2

stkHubPrtSecID

A unique identifier of the security of a given port within its module.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.7.1.3.1.3

stkHubPrtSecurityEnable

The value of this attribute determines application of the
port security.

Enumerationr/w

Constraints:
range: 1-2000

.1.3.6.1.4.1.164.7.1.3.1.4

stkHubPrtSecurityPattern

A six-octet(48 bit) pattern: where the masked bits of stkHubPortSecurityMask
need to match the MAC address.

OctetStringr/w

.1.3.6.1.4.1.164.7.1.3.1.5

stkHubPrtSecurityMask

Mask of the allowed MAC address that can be connected through
this port. The security of the individual port over writes the
security of the segment where the port belongs to

OctetStringr/w

.1.3.6.1.4.1.164.7.1.3.1.6

stkHubTRMdlTable

table

.1.3.6.1.4.1.164.7.2.2.1 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk stkHubTRMdlTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::stkHubTRMdlTable'

Bridge Hub Module table for TR media type
Contains general information about the Module

stkHubTRMdlEntry row .1.3.6.1.4.1.164.7.2.2.1.1

An entry in table stkHubTRMdlTable.

Indexes

No indexes recorded

Column Syntax OID

stkHubTRMdlID

A unique identifier of the module in stack. Internal module identifier
is always 1

Integer32

.1.3.6.1.4.1.164.7.2.2.1.1.1

stkHubTRMdlType

Indicates the type of the module connected with specific identifier

Enumeration

.1.3.6.1.4.1.164.7.2.2.1.1.2

stkHubTRMdlReset

When this object is set to the value of ON(3),
the module performs software reset. Upon completion, a trap will
be issued to the management station and the value
will be set to OFF.

Enumerationr/w

.1.3.6.1.4.1.164.7.2.2.1.1.3

stkHubTRMdlLed

This entry specifies the LEDs status in the module . Each led will
be represented by 4 bits where the first 2 bits will specify the
status (NA, OFF, ON, BLINK), and the next two bits
will specify the color (RED, GRE…

OctetString

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.7.2.2.1.1.4

stkHubTRMdlSpeed

Attribute describing the bandwidth of the media as set by the module
switch.
For certain products, if the value of stkHubTRMdlMngState
is 'enabled', then stkHubTRMdlSpeed can be set to the desired
value. Else, …

Enumerationr/w

.1.3.6.1.4.1.164.7.2.2.1.1.5

stkHubTRMdlMngState

This object indicates the status of the Manage switch
as set on the back panel of the main module.
'enabled' - means that management can override setting of
some HW switch/es.

Enumeration

.1.3.6.1.4.1.164.7.2.2.1.1.6

stkHubTRMdlAutodisable

Attribute describing the status of port Autodisable
mechanism, that protects against inserting in Token Ring
adapters at the wrong speed.
For certain products, if the value of stkHubTRMdlMngState
is 'enabled', then s…

Enumerationr/w

Constraints:
range: 1-200

.1.3.6.1.4.1.164.7.2.2.1.1.7

stkHubTRMdlConfigMsg

Full configuration message coded in internal RND application format.
This entry describes module' configuration.

OctetString

Constraints:
range: 0-100

.1.3.6.1.4.1.164.7.2.2.1.1.8

stkHubTRPrtTable

table

.1.3.6.1.4.1.164.7.2.3.1 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk stkHubTRPrtTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::stkHubTRPrtTable'

Bridge Hub  port table for TR media type
Contains general information about the ports.

stkHubTRPrtEntry row .1.3.6.1.4.1.164.7.2.3.1.1

An entry in table stkHubTRPrtTable.

Indexes

No indexes recorded

Column Syntax OID

stkHubTRPrtMdlID

A unique identifier of the module this port is attached to.

SNMPv2-SMIInteger32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.7.2.3.1.1.1

stkHubTRPrtID

A unique identifier of the port within its module.

SNMPv2-SMIInteger32

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.7.2.3.1.1.2

stkHubTRPrtFunctionality

Describes the functionality of the port in a Token ring topology

Enumeration

.1.3.6.1.4.1.164.7.2.3.1.1.3

stkHubTRPrtConnectorType

Type of hardware connector in the port.

Enumeration

.1.3.6.1.4.1.164.7.2.3.1.1.4

stkHubTRPrtAdminCmd

By setting this attribute to DISABLE(2) or SHORT(4) the
management station can force this lobe/port-connection to be
removed and block any access to the network via this lobe/port.
It is not mandatory that a certain …

Enumerationr/w

Constraints:
range: 1-200

.1.3.6.1.4.1.164.7.2.3.1.1.5

stkHubTRPrtActiveState

This attribute describes the electrical or optical activity
state of a lobe or the state of a port. Certain values may
not be applicable in some cases

Enumeration

Constraints:
range: 0-100

.1.3.6.1.4.1.164.7.2.3.1.1.6

stkHubTRPrtTrapMaskEnable

When this attribute is set to OFF by the management console the
agent starts sending the unmasked traps related to this port.
Otherwise no traps from this port are sent.

Enumerationr/w

.1.3.6.1.4.1.164.7.2.3.1.1.7

stkHubTRPrtStatus

This attribute indicates the status of this lobe/port connection:
DISABLED-(2) to (6) indicates the reason for the disabled state.
INSERTED(7)indicates that the lobe hardware inserts this lobe into
the ring , thus it b…

Enumeration

Constraints:
range: 0-12

.1.3.6.1.4.1.164.7.2.3.1.1.8

stkHubTRPrtCableProtectEnable

The value of this attribute determines activation of the cable-fault
protection mechanism of TCR and the optical link mechanism of
TFR and TFC .

Enumeration

Constraints:
range: 0-255

.1.3.6.1.4.1.164.7.2.3.1.1.9

stkHubTRPrtFlipProtectEnable

The value of this attribute determines activation of the flipping-lobe
protection mechanism of the port.

Enumerationr/w

.1.3.6.1.4.1.164.7.2.3.1.1.10

stkHubTRPrtMACAddress

The value of this object is the specific MAC address
of this interface which uniquely identifies this Interface
on a ring.

MacAddress

Type Constraints:
range: 6

.1.3.6.1.4.1.164.7.2.3.1.1.11

stkHubTRPrtType

Type of the port specific hardware

Enumeration

.1.3.6.1.4.1.164.7.2.3.1.1.12

stkHubETMdlTable

table

.1.3.6.1.4.1.164.7.3.2.1 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk stkHubETMdlTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::stkHubETMdlTable'

Bridge Hub Module table for ET media type
Contains general information about the Module

stkHubETMdlEntry row .1.3.6.1.4.1.164.7.3.2.1.1

An entry in table stkHubETMdlTable.

Indexes

No indexes recorded

Column	Syntax	OID
stkHubETMdlID A unique identifier of the module in stack. Internal module identifier is always 1	Integer32	`.1.3.6.1.4.1.164.7.3.2.1.1.1`
stkHubETMdlLed This entry specifies the LEDs status in the module . Each led will be represented by 4 bits where the first 2 bits will specify the status (NA, OFF, ON, BLINK), and the next two bits will specify the color (RED, GRE…	OctetString	`.1.3.6.1.4.1.164.7.3.2.1.1.2`
stkHubETMdlReset When this object is set to the value of hwReset(3), the module performs HW reset. When this object is set to the value of configReset(4), the module performs Configuration reset. Upon completion, a trap will be is…	Enumerationr/w	`.1.3.6.1.4.1.164.7.3.2.1.1.3`

pktSwchRoutSTable

table

.1.3.6.1.4.1.164.8.1.2.1 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchRoutSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchRoutSTable'

The Scratch Routing Table defines the routes for incoming and
outgoing data on the device.

pktSwchRoutSEntry row .1.3.6.1.4.1.164.8.1.2.1.1

Defines the contents of each line in the Scratch Routing Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchRoutIdS

Index of the pktSwchRoutSTable.

Integer32

.1.3.6.1.4.1.164.8.1.2.1.1.1

pktSwchRoutAddressS

The address to which the entry applies. The use of the octet
string syntax allows the use of the letter x as a wild card in
the addresses.

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.2.1.1.2

pktSwchRoutDestLink1S

First destination link through which the data will be routed.
For X.25 destination: any valid x.25 link no.
For Frame Relay Link: any valid dlci with an x.25 encapsulation
protocol, presented in th…

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.2.1.1.3

pktSwchRoutDestLink2S

Second destination link through which the data will be routed.
For X.25 destination: any valid x.25 link no.
For Frame Relay Link: any valid dlci with an x.25 encapsulation
protocol, presented in t…

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.2.1.1.4

pktSwchRoutDestLink3S

Third destination link through which the data will be routed.
For X.25 destination: any valid x.25 link no.
For Frame Relay Link: any valid dlci with an x.25 encapsulation
protocol, presented in th…

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.2.1.1.5

pktSwchRoutLinkPrio1S

A priority of the associated destination of link 1.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.1.2.1.1.6

pktSwchRoutLinkPrio2S

A priority of the associated destination of link 2.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.1.2.1.1.7

pktSwchRoutLinkPrio3S

A priority of the associated destination of link 3.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.1.2.1.1.8

pktSwchRoutSearchStatusS

off - The device stops searching for a matching address.
on - The device continues searching for a matching address in the
links of the next entry.

Enumerationr/w

.1.3.6.1.4.1.164.8.1.2.1.1.9

pktSwchRoutStatusS

The status of this routing table entry. The choices are those defined in the SNMPv2 Textual
Conventions for RowStatus. This will allow easy replacement of the INTEGER syntax with
the RowStatus textual convention SYNTA…

Enumerationr/w

.1.3.6.1.4.1.164.8.1.2.1.1.10

pktSwchRoutATable

table

.1.3.6.1.4.1.164.8.1.2.2 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchRoutATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchRoutATable'

The Active Routing Table defines the active routes for incoming and outgoing data
on the device.

pktSwchRoutAEntry row .1.3.6.1.4.1.164.8.1.2.2.1

Defines the contents of each line in the Active Routing Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchRoutIdA

Index of the pktSwchRoutATable.

Integer32

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

.1.3.6.1.4.1.164.8.1.2.2.1.1

pktSwchRoutAddressA

The address to which the entry applies. The use of the octet string syntax allows
the use of the letter x as a wild card in the addresses.

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.2.2.1.2

pktSwchRoutDestLink1A

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.2.2.1.3

pktSwchRoutDestLink2A

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.2.2.1.4

pktSwchRoutDestLink3A

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.2.2.1.5

pktSwchRoutLinkPrio1A

A priority of the associated destination of link 1.

SNMPv2-SMIInteger32

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.1.2.2.1.6

pktSwchRoutLinkPrio2A

A priority of the associated destination of link 2.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.1.2.2.1.7

pktSwchRoutLinkPrio3A

A priority of the associated destination of link 3.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.1.2.2.1.8

pktSwchRoutSearchStatusA

off - The device stops searching for a matching address.
on - The device continues searching for a matching address in the
links of the next entry.

Enumeration

.1.3.6.1.4.1.164.8.1.2.2.1.9

pktSwchPvcSTable

table

.1.3.6.1.4.1.164.8.1.2.3 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchPvcSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchPvcSTable'

The Scratch Network PVC Table defines the network PVCs.

pktSwchPvcSEntry row .1.3.6.1.4.1.164.8.1.2.3.1

Defines the contents of each line in the Scratch Network PVC table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchPvcNumS

The PVC number corresponding to this entry.

Integer32

.1.3.6.1.4.1.164.8.1.2.3.1.1

pktSwchPvcSrcLinkS

The number of the link (1 through 6 for SPS-6 and 1 through 12 for SPS-12) that will be
used as a source link to create a connection by means of the PVC.
0 means that the PVC will not be active, 100 means that this pvc…

Integer32r/w

.1.3.6.1.4.1.164.8.1.2.3.1.2

pktSwchPvcSrcLcnS

Network pvc:
The number of the logical channel (0-255) that will be used as the source
logical channel to create a connection by means of the PVC.

Local pvc:
For asynchronous channel to X.25 PVC,
Any va…

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.2.3.1.3

pktSwchPvcDstLinkS

The number of the destination link that will be used.
0 means that the PVC will not be active.

Integer32r/w

.1.3.6.1.4.1.164.8.1.2.3.1.4

pktSwchPvcDstLcnS

The number of the logical channel for the destination link.

Integer32r/w

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

.1.3.6.1.4.1.164.8.1.2.3.1.5

pktSwchPvcStatusS

The status of this Network PVC table entry. The choices are those defined in the SNMPv2
Textual Conventions for RowStatus. This will allow easy replacement of the INTEGER syntax
with the RowStatus textual convention S…

Enumerationr/w

.1.3.6.1.4.1.164.8.1.2.3.1.6

pktSwchPvcATable

table

.1.3.6.1.4.1.164.8.1.2.4 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchPvcATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchPvcATable'

The Active Network PVC Table defines the active network PVCs.

pktSwchPvcAEntry row .1.3.6.1.4.1.164.8.1.2.4.1

Defines the contents of each line in the Active Network PVC table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchPvcNumA

The PVC number corresponding to this entry.

Integer32

.1.3.6.1.4.1.164.8.1.2.4.1.1

pktSwchPvcSrcLinkA

The number of the link (1 through 6 for SPS-6 and 1 through 12 for SPS-12) that is
used as a source link to create a connection by means of the PVC.
0 means that the PVC will not be active, 100 means that this pvc is L…

Integer32

.1.3.6.1.4.1.164.8.1.2.4.1.2

pktSwchPvcSrcLcnA

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.2.4.1.3

pktSwchPvcDstLinkA

The number of the destination link that is used.
0 means that the PVC will not be active.

Integer32

Enumerated Values:

1	ipPid
2	snapPid

.1.3.6.1.4.1.164.8.1.2.4.1.4

pktSwchPvcDstLcnA

The number of the logical channel for the destination link.

Integer32

.1.3.6.1.4.1.164.8.1.2.4.1.5

pktSwchNuiSTable

table

.1.3.6.1.4.1.164.8.1.3.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchNuiSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchNuiSTable'

The NUI Table defines the NUIs that can be used by the device.

pktSwchNuiSEntry row .1.3.6.1.4.1.164.8.1.3.1.1

Defines the contents of each line in the NUI Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchNuiIndexS

The index of this entry.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.1.3.1.1.1

pktSwchNuiGroupIdS

The group Id for this NUI entry.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.1.3.1.1.2

pktSwchNuiInPasswdS

The password for the incoming call. 15 chars.

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.3.1.1.3

pktSwchNuiOutPasswdPointerS

A pointer to the password in the OutPasswdTable for an outgoing call.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.1.3.1.1.4

pktSwchNuiInAddrS

The addresss for the incoming call. 15 digits.

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.3.1.1.5

pktSwchNuiOutAddrPointerS

A pointer to the address in the OutAddrTable for an outgoing call.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.1.3.1.1.6

pktSwchNuiStatusS

The status of this NUI table entry. The choices are those defined in the SNMPv2 Textual
Conventions for RowStatus. This will allow easy replacement of the INTEGER syntax with
the RowStatus textual convention SYNTAX.

Enumerationr/w

.1.3.6.1.4.1.164.8.1.3.1.1.7

pktSwchNuiATable

table

.1.3.6.1.4.1.164.8.1.3.2 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchNuiATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchNuiATable'

The NUI Table defines the NUIs that can be used by the device.

pktSwchNuiAEntry row .1.3.6.1.4.1.164.8.1.3.2.1

Defines the contents of each line in the NUI Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchNuiIndexA

The index of this entry.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.1.3.2.1.1

pktSwchNuiGroupIdA

The group Id for this NUI entry.

SNMPv2-SMIInteger32

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.1.3.2.1.2

pktSwchNuiInPasswdA

The password for the incoming call. 15 chars.

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.3.2.1.3

pktSwchNuiOutPasswdPointerA

A pointer to the password in the OutPasswdTable for an outgoing call.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.1.3.2.1.4

pktSwchNuiInAddrA

The addresss for the incoming call. 15 digits.

SNMPv2-TCDisplayString

Constraints:
range: 1-200

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.3.2.1.5

pktSwchNuiOutAddrPointerA

A pointer to the address in the OutAddrTable for an outgoing call.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.1.3.2.1.6

pktSwchNuiStatusA

Enumeration

.1.3.6.1.4.1.164.8.1.3.2.1.7

pktSwchNuiOutPasswdSTable

table

.1.3.6.1.4.1.164.8.1.3.3 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchNuiOutPasswdSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchNuiOutPasswdSTable'

The table defines the passwords that can be used by the device.

pktSwchNuiOutPasswdSEntry row .1.3.6.1.4.1.164.8.1.3.3.1

Defines the contents of each line in OutPasswd Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchNuiOutPasswdIndexS

The index of this entry.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.1.3.3.1.1

pktSwchNuiOutPasswdValueS

The password of this entry. 15 chars.

SNMPv2-TCDisplayStringr/w

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.3.3.1.2

pktSwchNuiOutPasswdStatusS

The status of this NuiOutPasswd table entry.

Enumerationr/w

.1.3.6.1.4.1.164.8.1.3.3.1.3

pktSwchNuiOutPasswdATable

table

.1.3.6.1.4.1.164.8.1.3.4 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchNuiOutPasswdATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchNuiOutPasswdATable'

The table defines the passwords that can be used by the device.

pktSwchNuiOutPasswdAEntry row .1.3.6.1.4.1.164.8.1.3.4.1

Defines the contents of each line in OutPasswd Table.

Indexes

No indexes recorded

Column	Syntax	OID
pktSwchNuiOutPasswdIndexA The index of this entry.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.8.1.3.4.1.1`
pktSwchNuiOutPasswdValueA The password of this entry. 15 chars.	SNMPv2-TCDisplayString Type Constraints: `range: 0..255` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.164.8.1.3.4.1.2`
pktSwchNuiOutPasswdStatusA The status of this NuiOutPasswd table entry.	Enumeration Constraints: `range: 1-200`	`.1.3.6.1.4.1.164.8.1.3.4.1.3`

pktSwchNuiOutAddrSTable

table

.1.3.6.1.4.1.164.8.1.3.5 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchNuiOutAddrSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchNuiOutAddrSTable'

The table defines the Addresses that can be used by the device.

pktSwchNuiOutAddrSEntry row .1.3.6.1.4.1.164.8.1.3.5.1

Defines the contents of each line in OutAddr Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchNuiOutAddrIndexS

The index of this entry.

SNMPv2-SMIInteger32

Enumerated Values:

1	slip
2	x25SVC
3	x25PVC
4	frameRelay
5	hdlc
6	snmpAgent
7	ethernet
8	ppp
255	none

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.1.3.5.1.1

pktSwchNuiOutAddrValueS

The address of this entry. 15 digits.

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.3.5.1.2

pktSwchNuiOutAddrStatusS

The status of this NuiOutAddr table entry.

Enumerationr/w

.1.3.6.1.4.1.164.8.1.3.5.1.3

pktSwchNuiOutAddrATable

table

.1.3.6.1.4.1.164.8.1.3.6 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchNuiOutAddrATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchNuiOutAddrATable'

The table defines the Addresses that can be used by the device.

pktSwchNuiOutAddrAEntry row .1.3.6.1.4.1.164.8.1.3.6.1

Defines the contents of each line in OutAddr Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchNuiOutAddrIndexA

The index of this entry.

SNMPv2-SMIInteger32

Enumerated Values:

1	discard
2	flowControl
3	normal

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.1.3.6.1.1

pktSwchNuiOutAddrValueA

The address of this entry. 15 digits.

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.3.6.1.2

pktSwchNuiOutAddrStatusA

The status of this NuiOutAddr table entry.

Enumeration

.1.3.6.1.4.1.164.8.1.3.6.1.3

pktSwchMngX25TrapIpTable

table

.1.3.6.1.4.1.164.8.1.4.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchMngX25TrapIpTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchMngX25TrapIpTable'

This table indicates  the destination address of the traps.
Internally it will be limited to ten addresses.

pktSwchMngX25Entry row .1.3.6.1.4.1.164.8.1.4.1.1

An entry in table pktSwchMngX25TrapIpTable.

Indexes

No indexes recorded

Column	Syntax	OID
pktSwchMngID This value indicates an index of a specific IP address	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.8.1.4.1.1.1`
pktSwchMngIP This value indicates the destination address of the traps. IP 0.0.0.0 removes the entry.	RFC1155-SMIIpAddressr/w Constraints: `range: 1-4`	`.1.3.6.1.4.1.164.8.1.4.1.1.2`
pktSwchMngPhyAddrdeprecated This value indicates the physical destination address of the traps.	SNMPv2-TCDisplayStringr/w Constraints: `range: 0-60000` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.164.8.1.4.1.1.3`
pktSwchTrapEnable This value indicates which traps should be sent. The value is a sum of values (powers of two), where each value in the sum represents a trap that should be reported to the Management Station. The values that may be incl…	SNMPv2-SMIInteger32r/w Constraints: `range: 0-65535`	`.1.3.6.1.4.1.164.8.1.4.1.1.4`
pktSwchEncapsulationModedeprecated Format type for IP over X25	Enumerationr/w	`.1.3.6.1.4.1.164.8.1.4.1.1.5`

pktSwchXidSTable

table

.1.3.6.1.4.1.164.8.1.5.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchXidSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchXidSTable'

The Exchange Id table contains a list of 13 incoming pairs of allowed
dial-up phone numbers and passwords. Also included is one pair of
outgoing phone number and password (InternalIndex=14).

pktSwchXidSEntry row .1.3.6.1.4.1.164.8.1.5.1.1

An entry in table pktSwchXidSTable.

Indexes

No indexes recorded

Column Syntax OID

pktSwchXidIndexS

This Index of the XID table.

SNMPv2-SMIInteger32

Constraints:
range: 0-126

.1.3.6.1.4.1.164.8.1.5.1.1.1

pktSwchXidInternalIndexS

An internal index for each XidIndex of the table. The first 13 entries
refer to Incoming calls. The 14th entry refers to an Outgoing call.

SNMPv2-SMIInteger32

Enumerated Values:

1	echEn
2	noEch

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.1.5.1.1.2

pktSwchXidPasswdS

Password of size 16 chars.

SNMPv2-TCDisplayStringr/w

Constraints:
range: 0-127

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.5.1.1.3

pktSwchXidPhoneS

Phone number of size 16 digits.

SNMPv2-TCDisplayStringr/w

Constraints:
range: 0-255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.5.1.1.4

pktSwchXidStatusS

The status of the XID table entry. The status applies to the XidIndex,
i.e., setting the staus to invalid results in the removal of all
the InternalIndex entries (1..14) belonging to the relevant XidIndex.

Enumerationr/w

Enumerated Values:

1	trans
2	transAndCom
255	noFlow

.1.3.6.1.4.1.164.8.1.5.1.1.5

pktSwchXidATable

table

.1.3.6.1.4.1.164.8.1.5.2 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchXidATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchXidATable'

The Exchange Id table contains a list of 13 incoming pairs of allowed
dial-up phone numbers and passwords. Also included is one pair of
outgoing phone number and password (InternalIndex=14).

pktSwchXidAEntry row .1.3.6.1.4.1.164.8.1.5.2.1

An entry in table pktSwchXidATable.

Indexes

No indexes recorded

Column Syntax OID

pktSwchXidIndexA

This Index of the XID table.

SNMPv2-SMIInteger32

Enumerated Values:

1	discOut
2	normal

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.1.5.2.1.1

pktSwchXidInternalIndexA

An internal index for each XidIndex of the table. The first 13 entries
refer to Incoming calls. The 14th entry refers to an Outgoing call.

SNMPv2-SMIInteger32

Constraints:
range: 0-127

.1.3.6.1.4.1.164.8.1.5.2.1.2

pktSwchXidPasswdA

Password of size 16 chars.

SNMPv2-TCDisplayString

Constraints:
range: 0-255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.5.2.1.3

pktSwchXidPhoneA

Phone number of size 16 digits.

SNMPv2-TCDisplayString

Enumerated Values:

1	s110bps
2	s300bps
3	s1200bps
4	s600bps
5	s75bps
6	s150bps
12	s2400bps
13	s4800bps
14	s9600bps
15	s19200bps
19	s38400bps
20	s57600bps
21	s115200bps

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.5.2.1.4

pktSwchXidStatusA

Enumeration

Enumerated Values:

1	flowCont
2	noFlowCont

.1.3.6.1.4.1.164.8.1.5.2.1.5

pktSwchIpRoutSTable

table

.1.3.6.1.4.1.164.8.1.6.1 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchIpRoutSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchIpRoutSTable'

The Scratch Routing Table defines the routes for incoming and
outgoing ip datagrams on the device.

pktSwchIpRoutSEntry row .1.3.6.1.4.1.164.8.1.6.1.1

Defines the contents of each line in the Scratch IP Routing
Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchIpRoutIdS

Index of the pktSwchIpRoutSTable.

Integer32

Enumerated Values:

1	edit
2	noEdit

.1.3.6.1.4.1.164.8.1.6.1.1.1

pktSwchIpRoutIpAddressS

The IP address to which the entry applies.
A string of the format: X.X.X.X
where every X is a number in the range 0-255.

RFC1155-SMIIpAddressr/w

Constraints:
range: 0-127

.1.3.6.1.4.1.164.8.1.6.1.1.2

pktSwchIpRoutIpMaskS

The IP mask to which the entry applies.
A string of the format: X.X.X.X
where every X is a number in the range 0-255.

RFC1155-SMIIpAddressr/w

Constraints:
range: 0-127

.1.3.6.1.4.1.164.8.1.6.1.1.3

pktSwchIpRoutDestProtocolSdeprecated

Destination protocol for the associated address.
None(255) when not used

Enumerationr/w

Constraints:
range: 0-127

.1.3.6.1.4.1.164.8.1.6.1.1.4

pktSwchIpRoutDestinationSdeprecated

Destination for the associated address.
Possible values:
Default : Not Used.
X.25 PVC: Port:LCN or a pre defined PVC number
X.25 SVC: X.25 Addr or cid followed by a predefined Call ID number
Frame Relay: P…

SNMPv2-TCDisplayStringr/w

Constraints:
range: 0-126

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.6.1.1.5

pktSwchIpRoutInactivitySdeprecated

Inactivity time in steps of 50 mili seconds for X25 SVC
protocol only. Range: 0..255. Default: 2.

SNMPv2-SMIInteger32r/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.1.6.1.1.6

pktSwchIpRoutStatusS

The status of this routing table entry. The choices are those
defined in the SNMPv2 Textual Conventions for RowStatus.
This will allow easy replacement of the INTEGER syntax with
the RowStatus textual convention SYNTAX.

Enumerationr/w

Enumerated Values:

1	parCheck
2	parGen
3	checkAndGen
255	noPar

.1.3.6.1.4.1.164.8.1.6.1.1.7

pktSwchIpRoutMetricS

No. of hops for this route.
The default value is 1.
Legal values: 1 to the max no. of hops this device will support.
The max no. is defined by pktSwchIpGlobalMaxHopCount.

SNMPv2-SMIInteger32r/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.1.6.1.1.8

pktSwchIpRoutNextHopS

IP address of the next hop.
A string of the format: X.X.X.X
where every X is a number in the range 0-255.

RFC1155-SMIIpAddressr/w

Constraints:
range: 5-8

.1.3.6.1.4.1.164.8.1.6.1.1.9

pktSwchIpRoutInterfaceIdS

ID of the logical IP interface in the pktSwchIpInterface table.
The IP routing module will route the IP frame according to this
interface ID.
Legal values: 1 to 200 and 65535.
1-200 : ID of interface.
65535 : No IP inte…

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	space
2	mark
3	even
4	odd
255	none

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.1.6.1.1.10

pktSwchIpRoutATable

table

.1.3.6.1.4.1.164.8.1.6.2 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchIpRoutATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchIpRoutATable'

The Active Routing Table defines the active routes for incoming
and outgoing ip datagrams on the device.

pktSwchIpRoutAEntry row .1.3.6.1.4.1.164.8.1.6.2.1

Defines the contents of each line in the Active IP Routing Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchIpRoutIdA

Index of the IP pktSwchIpRoutATable.

Integer32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.1.6.2.1.1

pktSwchIpRoutIpAddressA

The IP address to which the entry applies.
A string of the format: X.X.X.X
where every X is a number in the range 0-255.

RFC1155-SMIIpAddress

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.1.6.2.1.2

pktSwchIpRoutIpMaskA

The IP mask to which the entry applies.
A string of the format: X.X.X.X
where every X is a number in the range 0-255.

RFC1155-SMIIpAddress

Constraints:
range: 0-127

.1.3.6.1.4.1.164.8.1.6.2.1.3

pktSwchIpRoutDestProtocolAdeprecated

Destination protocol for the associated address.
None(255) when not used.

Enumeration

Constraints:
range: 0-127

.1.3.6.1.4.1.164.8.1.6.2.1.4

pktSwchIpRoutDestinationAdeprecated

SNMPv2-TCDisplayString

Constraints:
range: 0-127

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.1.6.2.1.5

pktSwchIpRoutInactivityAdeprecated

Inactivity time in steps of 50 mili seconds for X25 SVC
protocol only. Range: 0..255. Default: 2.

SNMPv2-SMIInteger32

Constraints:
range: 0-127

.1.3.6.1.4.1.164.8.1.6.2.1.6

pktSwchIpRoutBuffsInA

The number of packets in the Input buffer link list,
received but not routed yet.

SNMPv2-SMICounter32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.1.6.2.1.7

pktSwchIpRoutBuffsOutA

The number of packets in the Output buffer link list,
routed but not sent yet.

SNMPv2-SMICounter32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.1.6.2.1.8

pktSwchIpRoutFCA

This is the flow control status of this ip routing
entry\connection

Enumeration

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.1.6.2.1.9

pktSwchIpRoutMetricA

No. of hops for this route.
The default value is 1.
Legal values: 1 to the max no. of hops this device will support.
The max no. is defined by pktSwchIpGlobalMaxHopCount.

SNMPv2-SMIInteger32

Constraints:
range: 0-5

.1.3.6.1.4.1.164.8.1.6.2.1.10

pktSwchIpRoutNextHopA

IP address of the next hop.
A string of the format: X.X.X.X
where every X is a number in the range 0-255.

RFC1155-SMIIpAddress

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

Type Constraints:
range: 4

.1.3.6.1.4.1.164.8.1.6.2.1.11

pktSwchIpRoutInterfaceIdA

SNMPv2-SMIInteger32

Constraints:
range: 0-20

.1.3.6.1.4.1.164.8.1.6.2.1.12

pktSwchTxPriorityTable

table

.1.3.6.1.4.1.164.8.1.7.2 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchTxPriorityTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchTxPriorityTable'

The Tx Priorities table.

pktSwchTxPriorityEntry row .1.3.6.1.4.1.164.8.1.7.2.1

The Tx Priority Entry defines the max delay time and max queue
length for each Priority level.

Indexes

No indexes recorded

Column	Syntax	OID
pktSwchTxPriorityLevel Level of an entry in the Tx Priority Table. At present, the PS supports 4 priority levels. Default level: 1	Integer32	`.1.3.6.1.4.1.164.8.1.7.2.1.1`
pktSwchTxPriorityMaxDelayTime Max delay time in Tx queue (in 100 msec intervals). Each frame will wait no more than the Max delay time until it is handled. 0 means that the delay is Unlimited. Default value: 0	Integer32r/w	`.1.3.6.1.4.1.164.8.1.7.2.1.2`
pktSwchTxPriorityMaxQueueLen Max allowed length of the Tx queue. Frames will be discarded if the length is exceeded. 0 means that the queue is of Unlimited length. Default value: 0	Integer32r/w Constraints: `range: 1-200`	`.1.3.6.1.4.1.164.8.1.7.2.1.3`

pktSwchProfileSTable

table

.1.3.6.1.4.1.164.8.2.1.1 · 1 row entry · 41 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchProfileSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchProfileSTable'

The Profile Table S defines the Scratch profiles that the PS can use to configure
a channel.

pktSwchProfileSEntry row .1.3.6.1.4.1.164.8.2.1.1.1

Defines the contents of each line in the Profile Table S.

Indexes

No indexes recorded

Column Syntax OID

pktSwchProfileNumberS

The number by which a profile is identified. This is also used as the index for the profile table.
The maximum profile number is 200.

Integer32

Constraints:
range: 0-127

.1.3.6.1.4.1.164.8.2.1.1.1.1

pktSwchProfileRecallCharS

The character specified by this entry is used to escape from the data transfer
mode and enter the PAD command mode. The integer values have the following meanings:
(0) PAD recall is not possible
(1)…

Integer32r/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.2.1.1.1.2

pktSwchProfileEchoS

This determines if an echo of the input characters is retured to the DTE.
The options are either 'echo enabled' or 'no echo'.

Enumerationr/w

Enumerated Values:

1	trans
2	transAndCom
255	noFlow

.1.3.6.1.4.1.164.8.2.1.1.1.3

pktSwchProfileDataForwCharS

The value is a sum of values (powers of two), where each value in the sum represents
a character (or characters) that is (are) used as a data forwarding character. The data
forwarding characters are used to instruct th…

Integer32r/w

Enumerated Values:

1	serv
4	prompt
5	servAndPrompt
255	noSig

.1.3.6.1.4.1.164.8.2.1.1.1.4

pktSwchProfileIdleTimerS

Packets will be forwarded when the idle timer expires. The idle time interval is specified
as a multiple of 50 milliseconds. The multiple is given by the parameter value. For example,
a value of 60 sets an interval o…

Integer32r/w

Constraints:
range: 0-31

.1.3.6.1.4.1.164.8.2.1.1.1.5

pktSwchProfileDevFlowContS

This parameter determines whether or not the PAD uses software flow control for the
attached device. The options are either (1) PAD uses flow control during data transfer
mode, (2) PAD uses flow control both in the da…

Enumerationr/w

Enumerated Values:

1	discOut
2	normal

.1.3.6.1.4.1.164.8.2.1.1.1.6

pktSwchProfileServSigS

This parameter is used to instruct the PAD whether to transfer PAD service signals and
the PAD prompt to the local DTE in standard format. The options are (1) PAD service
signals are transmitted to the DTE using the st…

Enumerationr/w

Constraints:
range: 0-127

.1.3.6.1.4.1.164.8.2.1.1.1.7

pktSwchProfileBreakS

The value is a sum of values (powers of two), where each value in the sum represents
a PAD operation on receipt of the break signal from the DTE.
The values that may be included in the sum and their meanings are:
0 No…

Integer32r/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.2.1.1.1.8

pktSwchProfileDiscOutS

This parameter instructs the PAD whether to forward the user sequences included in
data packets to the local DTE or discard them. The options are (1) discard output or
(2) normal data delivery. If the value of radSPS…

Enumeration

Enumerated Values:

1	s110bps
2	s300bps
3	s1200bps
4	s600bps
5	s75bps
6	s150bps
12	s2400bps
13	s4800bps
14	s9600bps
15	s19200bps
19	s38400bps
20	s57600bps
21	s115200bps

.1.3.6.1.4.1.164.8.2.1.1.1.9

pktSwchProfileCRPaddingS

This parameter specifies the number of padding characters to be added after a carriage
return character is transmitted to the local DTE.

Integer32r/w

Enumerated Values:

1	flowCont
2	noFlowCont

.1.3.6.1.4.1.164.8.2.1.1.1.10

pktSwchProfileLineFoldS

This parameter specifies the maximum number of characters to be inserted before the
format effector. If the value is zero, there is no insertion of a format effector (line folding).

Integer32r/w

Enumerated Values:

1	afterCR
2	recCR
4	echoCR
5	onePlusFour
6	twoPlusFour
7	oneTwoFour
255	noFeed

.1.3.6.1.4.1.164.8.2.1.1.1.11

pktSwchProfileSpeedS

This parameter determines the rate of data transmission to and from the DTE.

Enumerationr/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.2.1.1.1.12

pktSwchProfilePadFlowContS

This determines whether or not the terminal can exercise flow control over the PAD.
The options are either 'device can exercise flow control' or 'device cannot exercise flow
control.

Enumerationr/w

Enumerated Values:

1	edit
2	noEdit

.1.3.6.1.4.1.164.8.2.1.1.1.13

pktSwchProfileLineFeedInsertS

This parameter indicates when there is a line feed insertion after CR. The options are
(1) Insert line feed after transmission of CR to the DTE, (2) Insert line feed after receipt
of CR from the DTE, (4) Insert line fe…

Enumerationr/w

Constraints:
range: 0-127

.1.3.6.1.4.1.164.8.2.1.1.1.14

pktSwchProfileLineFeedPadS

This parameter specifies the number of padding characters to be added after a line
feed.

Integer32r/w

Constraints:
range: 0-127

.1.3.6.1.4.1.164.8.2.1.1.1.15

pktSwchProfileEditingS

This parameter specifies the editing capabilities available in the data transfer mode.
Editing is always possible when the PAD is in the command mode. The options are
(1) Command editing in the data trasfer mode is en…

Enumerationr/w

Constraints:
range: 0-127

.1.3.6.1.4.1.164.8.2.1.1.1.16

pktSwchProfileCharDelS

This parameter specifies the character delete, which is one character from IA5. The default
selection is 127 (character DEL).

Integer32r/w

Constraints:
range: 0-126

.1.3.6.1.4.1.164.8.2.1.1.1.17

pktSwchProfileLineDelS

This parameter specifies the line delete (last line stored in the edit buffer), which is one character from IA5. The default
selection is 24 (character CAN).

Integer32r/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.2.1.1.1.18

pktSwchProfileLineDispS

This entry specifies the line display character, which is one character
from IA5. The default selection is 18 (character DC2).

Integer32r/w

Enumerated Values:

1	parCheck
2	parGen
3	checkAndGen
255	noPar

.1.3.6.1.4.1.164.8.2.1.1.1.19

pktSwchProfileEditServSigS

This entry specifies the editing PAD service signals.
The integer values have the following meanings:
(0) No editing PAD service signals
(1) Editing PAD service signals for printing t…

Integer32r/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.2.1.1.1.20

pktSwchProfileEchomaskS

The value is a sum of values (powers of two), where each value in the sum represents
a character (or characters) that is (are) included in the echo mask. The characters in the
echo mask are not echoed to the DTE when P…

Integer32r/w

Constraints:
range: 5-8

.1.3.6.1.4.1.164.8.2.1.1.1.21

pktSwchProfileParTreatS

This entry controls the generation of parity bits in the data sent to the local DTE and the
checking of the parity bit when generated by the local DTE. The options are (1) parity
checking is enabled, (2) parity generat…

Enumerationr/w

Enumerated Values:

1	space
2	mark
3	even
4	odd
255	none

.1.3.6.1.4.1.164.8.2.1.1.1.22

pktSwchProfilePageWaitS

This entry specifies the number of line feed characters counted by the PAD before the
page wait condition is entered. If the value is zero, page wait is disabled.

Integer32r/w

Enumerated Values:

1	one
2	two
3	oneAndHalf

.1.3.6.1.4.1.164.8.2.1.1.1.23

pktSwchProfileBitsPerCharS

The number of data bits per character supported by the PAD.

Integer32r/w

Enumerated Values:

1	spec
2	noSpec

.1.3.6.1.4.1.164.8.2.1.1.1.24

pktSwchProfileDvParityS

This entry selects the type of parity to be checked and or generated by the PAD
when radSPSProfileParTreat is a value other than 255. The options are
(1) space parity, (2) mark parity, (3) even parity, (4) odd parity,…

Enumerationr/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.2.1.1.1.25

pktSwchProfileStopBitsS

This entry indicates the number of stop bits per character supported by the PAD.
The options are either (1) one stop bit, (2) two stop bits, or (3) 1.5 stop bits.

Enumerationr/w

Constraints:
range: 1-255

.1.3.6.1.4.1.164.8.2.1.1.1.26

pktSwchProfileSpecFlowS

This entry is used to define additional flow control possiblilites.
The options are either (1) Flow control by means of the terminal DTR line
or (2) No special flow control.

Enumerationr/w

Constraints:
range: 0-127

.1.3.6.1.4.1.164.8.2.1.1.1.27

pktSwchProfileCountFwdS

This entry can be used to instruct the PAD to complete the assembly of a packet
and to forward it after the specifed number of characters has been received.
If the value is zero, count forwarding is disabled.

Integer32r/w

Constraints:
range: 0-127

.1.3.6.1.4.1.164.8.2.1.1.1.28

pktSwchProfileEscDelayS

This entry can be used to instruct the PAD whether to delay the forwarding of
a data packet when an escape character is detected in the data stream and to
determine the required delay. The packet forwarding is delayed …

Integer32r/w

Constraints:
range: 0-127

.1.3.6.1.4.1.164.8.2.1.1.1.29

pktSwchProfileCharBreakS

This entry specifies the decimal value of the character that will be interpreted
as an additional break signal by the PAD. A value of zero indicates no break character.

Integer32r/w

Constraints:
range: 0-127

.1.3.6.1.4.1.164.8.2.1.1.1.30

pktSwchProfileCharSuppressS

This entry specifies the decimal value of the character that will toggle
echo suppression in the PAD. A value of zero indicates that echo suppression
is only controlled by radSPSProfileEcho.

Integer32r/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.2.1.1.1.31

pktSwchProfileCharSubsS

This entry specifies the decimal value of the character that will be echoed
instead of the character received from the user's DTE. A zero value indicates that
no character is echoed.

Integer32r/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.2.1.1.1.32

pktSwchProfileFormFeedPadS

This entry specifies the number of padding (NUL) characters that will be
automatically sent after the form feed character.

Integer32r/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.2.1.1.1.33

pktSwchProfileInactivityS

This entry specifies the number of minutes after which the PAD will forward
the accumulated data and clear the call. A zero value indicates no disconnection
on inactivity.

Integer32r/w

Constraints:
range: 0-5

.1.3.6.1.4.1.164.8.2.1.1.1.34

pktSwchProfileOptionsS

This entry defines several options to control the profile. The value is a sum of values
(powers of two), where each value in the sum represents an option .
The values that may be included in the sum and their meanings …

Integer32r/w

Constraints:
range: 0-20

.1.3.6.1.4.1.164.8.2.1.1.1.35

pktSwchProfileClrTimerS

This entry specifies the number of minutes after which a call is cleared.
If the parameter value is 0, there is no disconnection timer.

Integer32r/w

Constraints:
range: 0-20

.1.3.6.1.4.1.164.8.2.1.1.1.36

pktSwchProfileSubAddInCUDS

This entry defines the number of digits for the subaddress in CUD.

Integer32r/w

Constraints:
range: 0-20

.1.3.6.1.4.1.164.8.2.1.1.1.37

pktSwchProfileStatusS

The status of this profile. The choices are those defined in the SNMPv2 Textual Conventions
for RowStatus. This will allow easy replacement of the INTEGER syntax with the RowStatus
textual convention SYNTAX.

Enumerationr/w

.1.3.6.1.4.1.164.8.2.1.1.1.38

pktSwchProfileIncomingMsgS

This object enables the asynchronous user to change the 'com' message for
Incoming calls to a string of up to 20 characters.
If user selects the value xxx for this object, the PAD will convert it to
the relevant X.25 a…

OctetStringr/w

.1.3.6.1.4.1.164.8.2.1.1.1.39

pktSwchProfileOutgoingMsgS

This object enables the asynchronous user to change the 'com' message for
Outgoing calls to a string of up to 20 characters.
If user selects the value xxx for this object, the PAD will convert it to
the relevant X.25 a…

OctetStringr/w

.1.3.6.1.4.1.164.8.2.1.1.1.40

pktSwchProfileClearMsgS

This object enables the user to edit a message, which will appear when
the channel is cleared. The message is a string of up to 20 characters.
Example of such a string: 'Call Cleared'.

OctetStringr/w

Constraints:
range: 1-1224

.1.3.6.1.4.1.164.8.2.1.1.1.41

pktSwchProfileATable

table

.1.3.6.1.4.1.164.8.2.1.2 · 1 row entry · 40 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchProfileATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchProfileATable'

The Profile Table defines the profiles that the PS can use to configure
a channel.

pktSwchProfileAEntry row .1.3.6.1.4.1.164.8.2.1.2.1

Defines the contents of each line in the Profile Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchProfileNumberA

The number by which a profile is identified. This is also used as the index for the profile table.
The maximum profile number is 200.

Integer32

Constraints:
range: 0-200

.1.3.6.1.4.1.164.8.2.1.2.1.1

pktSwchProfileRecallCharA

Integer32

Constraints:
range: 0-200

.1.3.6.1.4.1.164.8.2.1.2.1.2

pktSwchProfileEchoA

This determines if an echo of the input characters is retured to the DTE.
The options are either 'echo enabled' or 'no echo'.

Enumeration

Constraints:
range: 0-200

.1.3.6.1.4.1.164.8.2.1.2.1.3

pktSwchProfileDataForwCharA

Integer32

Constraints:
range: 0-200

.1.3.6.1.4.1.164.8.2.1.2.1.4

pktSwchProfileIdleTimerA

Integer32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.2.1.2.1.5

pktSwchProfileDevFlowContA

Enumeration

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.2.1.2.1.6

pktSwchProfileServSigA

Enumeration

Constraints:
range: 0-200

.1.3.6.1.4.1.164.8.2.1.2.1.7

pktSwchProfileBreakA

Integer32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.2.1.2.1.8

pktSwchProfileDiscOutA

Enumeration

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.2.1.2.1.9

pktSwchProfileCRPaddingA

This parameter specifies the number of padding characters to be added after a carriage
return character is transmitted to the local DTE.

Integer32

Constraints:
range: 1-200

.1.3.6.1.4.1.164.8.2.1.2.1.10

pktSwchProfileLineFoldA

This parameter specifies the maximum number of characters to be inserted before the
format effector. If the value is zero, there is no insertion of a format effector (line folding).

Integer32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.2.1.2.1.11

pktSwchProfileSpeedA

This parameter determines the rate of data transmission to and from the DTE.

Enumeration

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.2.1.2.1.12

pktSwchProfilePadFlowContA

This determines whether or not the terminal can exercise flow control over the PAD.
The options are either 'device can exercise flow control' or 'device cannot exercise flow
control.

Enumeration

Enumerated Values:

1	noOp
2	clear

.1.3.6.1.4.1.164.8.2.1.2.1.13

pktSwchProfileLineFeedInsertA

Enumeration

.1.3.6.1.4.1.164.8.2.1.2.1.14

pktSwchProfileLineFeedPadA

This parameter specifies the number of padding characters to be added after a line
feed.

Integer32

.1.3.6.1.4.1.164.8.2.1.2.1.15

pktSwchProfileEditingA

Enumeration

Constraints:
range: 0-16383

.1.3.6.1.4.1.164.8.2.1.2.1.16

pktSwchProfileCharDelA

This parameter specifies the character delete, which is one character from IA5. The default
selection is 127 (character DEL).

Integer32

.1.3.6.1.4.1.164.8.2.1.2.1.17

pktSwchProfileLineDelA

This parameter specifies the line delete, which is one character from IA5. The default
selection is 24 (character CAN).

Integer32

.1.3.6.1.4.1.164.8.2.1.2.1.18

pktSwchProfileLineDispA

This entry specifies the line display character, which is one character
from IA5. The default selection is 18 (character DC2).

Integer32

.1.3.6.1.4.1.164.8.2.1.2.1.19

pktSwchProfileEditServSigA

This entry specifies the editing PAD service signals.
The integer values have the following meanings:
(0) No editing PAD service signals
(1) Editing PAD service signals for printing t…

Integer32

Constraints:
range: 1-288

.1.3.6.1.4.1.164.8.2.1.2.1.20

pktSwchProfileEchomaskA

Integer32

.1.3.6.1.4.1.164.8.2.1.2.1.21

pktSwchProfileParTreatA

Enumeration

.1.3.6.1.4.1.164.8.2.1.2.1.22

pktSwchProfilePageWaitA

This entry specifies the number of line feed characters counted by the PAD before the
page wait condition is entered. If the value is zero, page wait is disabled.

Integer32

.1.3.6.1.4.1.164.8.2.1.2.1.23

pktSwchProfileBitsPerCharA

The number of data bits per character supported by the PAD.

Integer32

.1.3.6.1.4.1.164.8.2.1.2.1.24

pktSwchProfileDvParityA

Enumeration

.1.3.6.1.4.1.164.8.2.1.2.1.25

pktSwchProfileStopBitsA

This entry indicates the number of stop bits per character supported by the PAD.
The options are either (1) one stop bit, (2) two stop bits, or (3) 1.5 stop bits.

Enumeration

.1.3.6.1.4.1.164.8.2.1.2.1.26

pktSwchProfileSpecFlowA

This entry is used to define additional flow control possiblilites.
The options are either (1) Flow control by means fo the terminal DTR line
or (2) No special flow control.

Enumeration

.1.3.6.1.4.1.164.8.2.1.2.1.27

pktSwchProfileCountFwdA

Integer32

.1.3.6.1.4.1.164.8.2.1.2.1.28

pktSwchProfileEscDelayA

Integer32

.1.3.6.1.4.1.164.8.2.1.2.1.29

pktSwchProfileCharBreakA

This entry specifies the decimal value of the character that will be interpreted
as an additional break signal by the PAD. A value of zero indicates no break character.

Integer32

.1.3.6.1.4.1.164.8.2.1.2.1.30

pktSwchProfileCharSuppressA

This entry specifies the decimal value of the character that will toggle
echo suppression in the PAD. A value of zero indicates that echo suppression
is only controlled by radSPSProfileEcho.

Integer32

.1.3.6.1.4.1.164.8.2.1.2.1.31

pktSwchProfileCharSubsA

This entry specifies the decimal value of the character that will be echoed
instead of the character received from the user's DTE. A zero value indicates that
no character is echoed.

Integer32

.1.3.6.1.4.1.164.8.2.1.2.1.32

pktSwchProfileFormFeedPadA

This entry specifies the number of padding (NUL) characters that will be
automatically sent after the form feed character.

Integer32

.1.3.6.1.4.1.164.8.2.1.2.1.33

pktSwchProfileInactivityA

This entry specifies the number of minutes after which the PAD will forward
the accumulated data and clear the call. A zero value indicates no disconnection
on inactivity.

Integer32

.1.3.6.1.4.1.164.8.2.1.2.1.34

pktSwchProfileOptionsA

Integer32

.1.3.6.1.4.1.164.8.2.1.2.1.35

pktSwchProfileClrTimerA

This entry specifies the number of minutes after which a call is cleared.
If the parameter value is 0, there is no disconnection timer.

Integer32

.1.3.6.1.4.1.164.8.2.1.2.1.36

pktSwchProfileSubAddInCUDA

This entry defines the number of digits for the subaddress in CUD.

Integer32

Constraints:
range: 1-200

.1.3.6.1.4.1.164.8.2.1.2.1.37

pktSwchProfileIncomingMsgA

This object is used by an asynchronous user to change the 'com' message for
Incoming calls to a string of up to 20 characters.
If user selects the value xxx for this object, the PAD will convert it to
the relevant X.25…

OctetString

.1.3.6.1.4.1.164.8.2.1.2.1.38

pktSwchProfileOutgoingMsgA

This object is used by an asynchronous user to change the 'com' message for
Outgoing calls to a string of up to 20 characters.
If user selects the value xxx for this object, the PAD will convert it to
the relevant X.25…

OctetString

.1.3.6.1.4.1.164.8.2.1.2.1.39

pktSwchProfileClearMsgA

This object is the message selected by user, which will appear when
the channel is cleared. The message is a string of up to 20 characters.
Example of such a string: 'Call Cleared'.

OctetString

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

.1.3.6.1.4.1.164.8.2.1.2.1.40

pktSwchChannelSTable

table

.1.3.6.1.4.1.164.8.2.2.1 · 1 row entry · 20 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchChannelSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchChannelSTable'

The Scratch Channel Table defines the channels configured on the PS.

pktSwchChannelSEntry row .1.3.6.1.4.1.164.8.2.2.1.1

Defines the contents of each line in the Scratch Channel Table.

Indexes

pktSwchCallIdNumberA

Column Syntax OID

pktSwchChannelIfIndexS

This is used as the index for the channel table.

SNMPv2-SMIInteger32

Constraints:
range: 1-200

.1.3.6.1.4.1.164.8.2.2.1.1.1

pktSwchChannelNumberS

The number by which a channel is identified.

Integer32

.1.3.6.1.4.1.164.8.2.2.1.1.2

pktSwchChannelProfileS

The profile that the channel uses for command mode operations.

Integer32r/w

.1.3.6.1.4.1.164.8.2.2.1.1.3

pktSwchChannelOutCallProfileS

The number of the profile that will be used during an outgoing
call on the channel.

Integer32r/w

.1.3.6.1.4.1.164.8.2.2.1.1.4

pktSwchChannelInCallProfileS

The number of the profile that will be used during an incoming
call on the channel.

Integer32r/w

.1.3.6.1.4.1.164.8.2.2.1.1.5

pktSwchChannelRemoteProfileS

The number of the profile that will be downloaded to the remote
PAD at the beginning of a new call.

Integer32r/w

Constraints:
range: 1-200

.1.3.6.1.4.1.164.8.2.2.1.1.6

pktSwchChannelAutocallIdS

Selects the mnemonic (call ID) to be used as the first alternative.
A value of zero indicates that the autocall function is disabled.

Integer32r/w

Constraints:
range: 0-64

.1.3.6.1.4.1.164.8.2.2.1.1.7

pktSwchChannelAlterAutocallIdS

Selects the alternate mnemonic for the autocall function. A value of zero indicates that the
alternate destination is not used.

Integer32r/w

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

.1.3.6.1.4.1.164.8.2.2.1.1.8

pktSwchChannelAutocallRetriesS

The number of autocall retries if the autocall setup request is
rejected with a busy cause.

Integer32r/w

.1.3.6.1.4.1.164.8.2.2.1.1.9

pktSwchChannelAutocallIntervalS

The interval in seconds between consecutive autocall retries.

Integer32r/w

.1.3.6.1.4.1.164.8.2.2.1.1.10

pktSwchChannelCallAliasS

The alias to be sent after the call is set up. A value of zero
indicates that alias sending is disabled. The aliases are
configured on the Alias Table.

Integer32r/w

Constraints:
range: 1-200

.1.3.6.1.4.1.164.8.2.2.1.1.11

pktSwchChannelSubAddress1S

The first subaddress for the channel.

Integer32r/w

Constraints:
range: 0-64

.1.3.6.1.4.1.164.8.2.2.1.1.12

pktSwchChannelSubAddress2S

The second subaddress for the channel.

Integer32r/w

.1.3.6.1.4.1.164.8.2.2.1.1.13

pktSwchChannelNUISEntry

The number corresponding to the NUI information to be sent.
This number is the same as the pktSwchNuiGroupId.

Integer32r/w

.1.3.6.1.4.1.164.8.2.2.1.1.14

pktSwchChannelClearTimerS

Time limitation for an open session. A value of zero indicates that
the Clear timer is not used.

Integer32r/w

.1.3.6.1.4.1.164.8.2.2.1.1.15

pktSwchChannelOptionsS

This controls the use of gneral non-correlated channel options.
The value is a sum of values (powers of two), where each value in
the sum represents an option.
The values that may be included in the sum and their meanin…

Integer32r/w

.1.3.6.1.4.1.164.8.2.2.1.1.16

pktSwchChannelClear

The Clearing Channel operation disconnects all sessions

Enumerationr/w

Enumerated Values:

1	engaged
2	free

.1.3.6.1.4.1.164.8.2.2.1.1.17

pktSwchChannelCopyTo

The destination channel number, to which the Copy
is performed.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.2.1.1.18

pktSwchChannelCopyToWMask

The destination channel number, to which the Copy with Mask
is performed.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.2.1.1.19

pktSwchChannelCopyMask

The selected configuration parameters to be copied from the source
channel to the target channels. The value is a sum of values
(powers of two), where each value in the sum represents a selected
parameter that is not co…

Integer32r/w

.1.3.6.1.4.1.164.8.2.2.1.1.20

pktSwchChannelATable

table

.1.3.6.1.4.1.164.8.2.2.2 · 1 row entry · 16 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchChannelATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchChannelATable'

The Active Channel Table defines the channels configured on the PS.

pktSwchChannelAEntry row .1.3.6.1.4.1.164.8.2.2.2.1

Defines the contents of each line in the Active Channel
Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchChannelIfIndexA

This is used as the index for the channel table.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.2.2.1.1

pktSwchChannelNumberA

The number by which a channel is identified.

Integer32

Enumerated Values:

1	no
2	yes

.1.3.6.1.4.1.164.8.2.2.2.1.2

pktSwchChannelProfileA

The profile that the channel uses for command mode operations.

SNMPv2-SMIInteger32

Enumerated Values:

1	no
2	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.2.2.1.3

pktSwchChannelOutCallProfileA

The number of the profile that is used during an outgoing call on the channel.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.2.2.1.4

pktSwchChannelInCallProfileA

The number of the profile that is used during an incoming call on the channel.

SNMPv2-SMIInteger32

Enumerated Values:

1	none
2	activeLink
3	x28command
4	dataTransfer

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.2.2.1.5

pktSwchChannelRemoteProfileA

The number of the profile that is downloaded to the remote PAD at the beginning of
a new call.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.2.2.1.6

pktSwchChannelAutocallIdA

Selects the mnemonic (call ID) to be used as the first alternative. A value of zero indicates that
the autocall function is disabled.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.2.2.1.7

pktSwchChannelAlterAutocallIdA

Selects the alternate mnemonic for the autocall function. A value of zero indicates that the
alternate destination is not used.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.2.2.1.8

pktSwchChannelAutocallRetriesA

The number of autocall retrues if the autocall setup request is rejected with a busy cause.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.2.2.1.9

pktSwchChannelAutocallIntervalA

The interval in seconds between consecutive autocall retries.

SNMPv2-SMIInteger32

Constraints:
range: 0-126

.1.3.6.1.4.1.164.8.2.2.2.1.10

pktSwchChannelCallAliasA

The alias to be sent after the call is set up. A value of zero indicates that alias
sending is disabled. The aliases are configured on the Alias Table.

SNMPv2-SMIInteger32

Enumerated Values:

1	echEn
2	noEch

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.2.2.1.11

pktSwchChannelSubAddress1A

The first subaddress for the channel.

SNMPv2-SMIInteger32

Constraints:
range: 0-127

.1.3.6.1.4.1.164.8.2.2.2.1.12

pktSwchChannelSubAddress2A

The second subaddress for the channel.

SNMPv2-SMIInteger32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.2.2.2.1.13

pktSwchChannelNUIAEntry

The number corresponding to the NUI information to be sent. This number is the same as the
pktSwchNuiIndex.

SNMPv2-SMIInteger32

Enumerated Values:

1	trans
2	transAndCom
255	noFlow

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.2.2.1.14

pktSwchChannelClearTimerA

Time limitation for an open session. A value of zero indicates that the Clear timer is not used.

SNMPv2-SMIInteger32

Enumerated Values:

1	serv
4	prompt
5	servAndPrompt
255	noSig

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.2.2.1.15

pktSwchChannelOptionsA

This controls the use of general non-correlated channel options. The value is a sum of values
(powers of two), where each value in the sum represents an option.
The values that may be included in the sum and their mean…

SNMPv2-SMIInteger32

Constraints:
range: 0-31

.1.3.6.1.4.1.164.8.2.2.2.1.16

pktSwchCallIdSTable

table

.1.3.6.1.4.1.164.8.2.3.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchCallIdSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchCallIdSTable'

The Call ID Table S defines the Scratch Call IDs configured on the device.

pktSwchCallIdSEntry row .1.3.6.1.4.1.164.8.2.3.1.1

Defines the contents of each line in the Scratch CallId Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchCallIdNumberS

The index of this entry.

Integer32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.2.3.1.1.1

pktSwchCallIdMnemonicS

The mnemonic for this call ID.

SNMPv2-TCDisplayStringr/w

Enumerated Values:

1	s110bps
2	s300bps
3	s1200bps
4	s600bps
5	s75bps
6	s150bps
12	s2400bps
13	s4800bps
14	s9600bps
15	s19200bps
19	s38400bps
20	s57600bps
21	s115200bps

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.2.3.1.1.2

pktSwchCallIdAddressS

The address for this call ID.

SNMPv2-TCDisplayStringr/w

Enumerated Values:

1	flowCont
2	noFlowCont

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.2.3.1.1.3

pktSwchCallIdStatusS

The status of this Call ID table entry. The choices are those defined in the SNMPv2 Textual
Conventions for RowStatus. This will allow easy replacement of the INTEGER syntax with
the RowStatus textual convention SYNTA…

Enumerationr/w

Enumerated Values:

1	afterCR
2	recCR
4	echoCR
5	onePlusFour
6	twoPlusFour
7	oneTwoFour
255	noFeed

.1.3.6.1.4.1.164.8.2.3.1.1.4

pktSwchCallIdATable

table

.1.3.6.1.4.1.164.8.2.3.2 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchCallIdATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchCallIdATable'

The Call ID Table A defines the Active Call IDs configured on the device.

pktSwchCallIdAEntry row .1.3.6.1.4.1.164.8.2.3.2.1

Defines the contents of each line in the Active CallId Table.

Indexes

No indexes recorded

Column	Syntax	OID
pktSwchCallIdNumberA The index of this entry.	Integer32 Constraints: `range: 0-127`	`.1.3.6.1.4.1.164.8.2.3.2.1.1`
pktSwchCallIdMnemonicA The mnemonic for this call ID.	SNMPv2-TCDisplayString Constraints: `range: 0-127` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.164.8.2.3.2.1.2`
pktSwchCallIdAddressA The address for this call ID.	SNMPv2-TCDisplayString Constraints: `range: 0-127` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.164.8.2.3.2.1.3`

pktSwchAliasSTable

table

.1.3.6.1.4.1.164.8.2.4.1 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchAliasSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchAliasSTable'

The Alias Table defines the aliases configured on the device.

pktSwchAliasSEntry row .1.3.6.1.4.1.164.8.2.4.1.1

Defines the contents of each line in the Alias Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchAliasNumberS

The index of this entry.

Integer32

Enumerated Values:

1	parCheck
2	parGen
3	checkAndGen
255	noPar

.1.3.6.1.4.1.164.8.2.4.1.1.1

pktSwchAliasValueS

The alias is defined using up to 64 characters.

OctetStringr/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.2.4.1.1.2

pktSwchAliasStatusS

The status of this Alias table entry. The choices are those defined in the SNMPv2 Textual
Conventions for RowStatus. This will allow easy replacement of the INTEGER syntax with
the RowStatus textual convention SYNTAX.

Enumerationr/w

.1.3.6.1.4.1.164.8.2.4.1.1.3

pktSwchAliasATable

table

.1.3.6.1.4.1.164.8.2.4.2 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchAliasATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchAliasATable'

The Alias Table defines the aliases configured on the device.

pktSwchAliasAEntry row .1.3.6.1.4.1.164.8.2.4.2.1

Defines the contents of each line in the Alias Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchAliasNumberA

The index of this entry.

Integer32

Enumerated Values:

1	x25
2	frameRelay
3	hdlc
4	sdlc
5	async
6	stm4
7	stm8
8	stm16
9	stm24
10	mpe
11	bscHpad
12	bscTpad
13	slip
14	ethernet
15	ppp

.1.3.6.1.4.1.164.8.2.4.2.1.1

pktSwchAliasValueA

The alias is defined using up to 64 characters.

OctetString

Enumerated Values:

1	x25
2	frameRelay
3	hdlc
4	sdlc
5	async
6	stm4
7	stm8
8	stm16
9	stm24
10	mpe
11	bscHpad
12	bscTpad
13	slip
14	ethernet
15	ppp

.1.3.6.1.4.1.164.8.2.4.2.1.2

pktSwchAsyncStatTable

table

.1.3.6.1.4.1.164.8.2.5 · 1 row entry · 13 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchAsyncStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchAsyncStatTable'

The AsyncStat Table includes status information and statistics
provided by the PS on the async channels.

pktSwchAsyncStatEntry row .1.3.6.1.4.1.164.8.2.5.1

Defines the contents of each line in the Async Stat Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchAsyncIfIndex

An index for the table.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.5.1.1

pktSwchAsyncChannelNumber

The channel to which this entry applies. This value is the
same as the pktSwchChannelNumber.

SNMPv2-SMIInteger32

Enumerated Values:

2	v24
3	v35
4	x21
5	rs530
6	acd
7	mobi
8	u
9	etherUtp
255	noConnector

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.5.1.2

pktSwchAsyncConnectionStatus

The connection status of the channel is either FREE or ENG (engaged).

Enumeration

.1.3.6.1.4.1.164.8.2.5.1.3

pktSwchAsyncNumLogChannels

The number of active logical channels used by the asynchronous channel.

SNMPv2-SMIInteger32

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.5.1.4

pktSwchAsyncNumActSessions

The number of active sessions opened by this asynchronous channel.

SNMPv2-SMIInteger32

Enumerated Values:

1	noOp
2	v54Local
3	v54Remote

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.5.1.5

pktSwchAsyncAutocallId

Indicates whether the channel has been configured to use the autocall function and
what is the call ID. NONE means that the channel is not configured for autocall.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.5.1.6

pktSwchAsyncRTSStatus

Shows the status of the RTS line of the asynchronous channel.
OFF indicates that the RTS line is not active, ON indicates that
it is active, and UNUSED indicates that the channel PAD is
programmed to disregard the state…

Enumeration

.1.3.6.1.4.1.164.8.2.5.1.7

pktSwchAsyncBuffToNet

The number of data buffers currently used by the transmit direction of the channel.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.5.1.8

pktSwchAsyncBuffToUser

The number of data buffers currently used by the receive direction of the channel.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.5.1.9

pktSwchAsyncTxXoff

The current state of software flow control in the transmit direction.
NO indicates that traffic flow is enabled. YES indicates that traffic
flow from the user's DTE to the device channel has been interrupted
by sending…

Enumeration

.1.3.6.1.4.1.164.8.2.5.1.10

pktSwchAsyncRxXoff

The current state of software flow control in the receive direction.
NO indicates that traffic flow is enabled. YES indicates that traffic
flow to the user's DTE from the device channel has been interrupted
by means of…

Enumeration

.1.3.6.1.4.1.164.8.2.5.1.11

pktSwchAsyncBuffOutstand

Indicates the number of buffers which were sent to the async user
but weren't yet freed.

SNMPv2-SMIInteger32

Enumerated Values:

1	r2400bps
2	r4800bps
3	r9600bps
4	r14400bps
5	r19200bps
6	r38400bps
7	r48Kbps
8	r56Kbps
9	r64Kbps
10	r128Kbps
11	r256Kbps
12	r384Kbps
13	r504Kbps
14	r768Kbps
15	r1008Kbps
16	r1466Kbps
17	r2016Kbps
255	external

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.2.5.1.12

pktSwchAsyncChannelMode

The channel mode is either X28 COMMAND or DATA TRANSFER.

Enumeration

Constraints:
range: 0-2048

.1.3.6.1.4.1.164.8.2.5.1.13

pktSwchAsyncRunProTable

table

.1.3.6.1.4.1.164.8.2.6 · 1 row entry · 24 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchAsyncRunProTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchAsyncRunProTable'

The AsyncRunPro Table includes status information and statistics provided by the PS
on the async channels.

pktSwchAsyncRunProEntry row .1.3.6.1.4.1.164.8.2.6.1

Defines the contents of each line in the Async RunPro Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchAsyncRunProIfIndex

An index for the table.

SNMPv2-SMIInteger32

Constraints:
range: 1-128

.1.3.6.1.4.1.164.8.2.6.1.1

pktSwchAsyncRunProChannelNumber

The channel to which this entry applies. This value is the same as the pktSwchChannelNumber.

SNMPv2-SMIInteger32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.2.6.1.2

pktSwchAsyncRunProRecallChar

Integer32

.1.3.6.1.4.1.164.8.2.6.1.3

pktSwchAsyncRunProEcho

This determines if an echo of the input characters is retured to the DTE.
The options are either 'echo enabled' or 'no echo'.

Enumeration

.1.3.6.1.4.1.164.8.2.6.1.4

pktSwchAsyncRunProDataForwChar

Integer32

.1.3.6.1.4.1.164.8.2.6.1.5

pktSwchAsyncRunProIdleTimer

Integer32

Enumerated Values:

1	r2400bps
2	r4800bps
3	r9600bps
4	r14400bps
5	r19200bps
6	r38400bps
7	r48Kbps
8	r56Kbps
9	r64Kbps
10	r128Kbps
11	r256Kbps
12	r384Kbps
13	r504Kbps
14	r768Kbps
15	r1008Kbps
16	r1466Kbps
17	r2016Kbps
255	external

.1.3.6.1.4.1.164.8.2.6.1.6

pktSwchAsyncRunProDevFlowCont

Enumeration

Constraints:
range: 0-2048

.1.3.6.1.4.1.164.8.2.6.1.7

pktSwchAsyncRunProServSig

Enumeration

Constraints:
range: 1-4096

.1.3.6.1.4.1.164.8.2.6.1.8

pktSwchAsyncRunProBreak

Integer32

Enumerated Values:

1	unknown
2	x25
3	fr
4	isdn

.1.3.6.1.4.1.164.8.2.6.1.9

pktSwchAsyncRunProDiscOut

Enumeration

.1.3.6.1.4.1.164.8.2.6.1.10

pktSwchAsyncRunProCRPPadding

This parameter specifies the number of padding characters to be added after a carriage
return character is transmitted to the local DTE.

Integer32

.1.3.6.1.4.1.164.8.2.6.1.11

pktSwchAsyncRunProLineFold

This parameter specifies the maximum number of characters to be inserted before the
format effector. If the value is zero, there is no insertion of a format effector (line folding).

Integer32

.1.3.6.1.4.1.164.8.2.6.1.12

pktSwchAsyncRunProSpeed

This parameter determines the rate of data transmission to and from the DTE.

Enumeration

.1.3.6.1.4.1.164.8.2.6.1.13

pktSwchAsyncRunProPadFlowCont

This determines whether or not the terminal can exercise flow control over the PAD.
The options are either 'device can exercise flow control' or 'device cannot exercise flow
control.

Enumeration

.1.3.6.1.4.1.164.8.2.6.1.14

pktSwchAsyncRunProLineFeedInsert

Enumeration

.1.3.6.1.4.1.164.8.2.6.1.15

pktSwchAsyncRunProLineFeedPad

This parameter specifies the number of padding characters to be added after a line
feed.

Integer32

.1.3.6.1.4.1.164.8.2.6.1.16

pktSwchAsyncRunProEditing

Enumeration

.1.3.6.1.4.1.164.8.2.6.1.17

pktSwchAsyncRunProCharDel

This parameter specifies the character delete, which is one character from IA5. The default
selection is 127 (character DEL).

Integer32

.1.3.6.1.4.1.164.8.2.6.1.18

pktSwchAsyncRunProLineDel

This parameter specifies the line delete, which is one character from IA5. The default
selection is 24 (character CAN).

Integer32

.1.3.6.1.4.1.164.8.2.6.1.19

pktSwchAsyncRunProLineDisp

This entry specifies the line display character, which is one character
from IA5. The default selection is 18 (character DC2).

Integer32

.1.3.6.1.4.1.164.8.2.6.1.20

pktSwchAsyncRunProEditServSig

This entry specifies the editing PAD service signals.
The integer values have the following meanings:
(0) No editing PAD service signals
(1) Editing PAD service signals for printing t…

Integer32

Constraints:
range: 1-128

.1.3.6.1.4.1.164.8.2.6.1.21

pktSwchAsyncRunProEchomask

Integer32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.2.6.1.22

pktSwchAsyncRunProParTreat

Enumeration

.1.3.6.1.4.1.164.8.2.6.1.23

pktSwchAsyncRunProPageWait

This entry specifies the number of line feed characters counted by the PAD before the
page wait condition is entered. If the value is zero, page wait is disabled.

Integer32

.1.3.6.1.4.1.164.8.2.6.1.24

pktSwchPhyInterfaceTable

table

.1.3.6.1.4.1.164.8.3 · 1 row entry · 13 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchPhyInterfaceTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchPhyInterfaceTable'

The Link Table defines the links configured on the PS.

pktSwchPhyInterfaceEntry row .1.3.6.1.4.1.164.8.3.1

Defines the contents of each line in the Link Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchPhyInterfaceIfIndex

The ifIndex identified with this link.

SNMPv2-SMIInteger32

Constraints:
range: 0-15

.1.3.6.1.4.1.164.8.3.1.1

pktSwchPhyInterfaceProtocolS

The protocol to be used on this link.

Note for PPP:
PPP protocol is allowed to be applied on Sync Links (1-3)
as well as Async channels (1-24).
In order to eliminate ambiguity in the IP destination where
…

Enumerationr/w

Enumerated Values:

1	cug
2	cugOa
3	cugIa
4	cugOaIa
5	noPref
255	noCug

.1.3.6.1.4.1.164.8.3.1.2

pktSwchPhyInterfaceProtocolA

The protocol currently used on this link.

Enumeration

.1.3.6.1.4.1.164.8.3.1.3

pktSwchPhyInterfaceCopyTo

The destination interface number, to which the Copy
is performed.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.3.1.4

pktSwchPhyInterfaceChanged

Indicates if the current running protocol is different than the defined
protocol

Enumeration

.1.3.6.1.4.1.164.8.3.1.5

pktSwchPhyInterfaceRxBuffInPool

The free data buffers in the Rx pool per interface

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.3.1.6

pktSwchPhyInterfaceConnector

The connector type of the interface

Enumeration

.1.3.6.1.4.1.164.8.3.1.7

pktSwchPhyInterfaceNeighborIp

The Ip address of the device on the other side of the link.

RFC1155-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.164.8.3.1.8

pktSwchPhyInterfaceProtocolStatus

The status of the Interface Protocol row in the Table.

Enumerationr/w

.1.3.6.1.4.1.164.8.3.1.9

pktSwchPhyInterfaceTestCmd

START/STOP a test on the current interface.
The available tests are:
v54Local - Local Analog Loopback (AL), L3 according to ITU-T standard.
v54Remote - Remote Digital Loopback(RDL), L2 according to ITU-T standard.
Fo…

Enumerationr/w

Constraints:
range: 0-15

.1.3.6.1.4.1.164.8.3.1.10

pktSwchPhyInterfaceTestTransmittedFrames

No. of frames which were transmitted from this interface
during the TEST.

SNMPv2-SMICounter32

Enumerated Values:

1	cug
2	cugOa
3	cugIa
4	cugOaIa
5	noPref
255	noCug

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.3.1.11

pktSwchPhyInterfaceTestReceivedFrames

No. of frames which were received on this interface
during the TEST.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.3.1.12

pktSwchPhyInterfaceTestLostFrames

Percentage of the frames which were lost during the TEST.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.3.1.13

pktSwchLapbSTable

table

.1.3.6.1.4.1.164.8.4.1.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchLapbSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchLapbSTable'

The Lapb Table includes statistics and configurable objects
provided by the PS that are not included in RFC 1381.

pktSwchLapbSEntry row .1.3.6.1.4.1.164.8.4.1.1.1

Defines the contents of each line in the RAD Lapb Table.

Indexes

pktSwchCugLinkNumberS pktSwchCugIndexS

Column Syntax OID

pktSwchLapbLinkNumberS

The link number with which this entry is associated. This value
corresponds to pktSwchPhyInterfaceNumber. There is an entry for
each link for which the pktSwchPhyInterfaceProtocol is X.25 and one
entry for each link …

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.4.1.1.1.1

pktSwchLapbInternalClockS

The internal clock speed to be used on this LAPB link. If external clock is used, the value is
255.

Enumerationr/w

.1.3.6.1.4.1.164.8.4.1.1.1.2

pktSwchLapbLineOptionS

The line option to be used on this link. A value of zero indicates
no options. A value between 0 and 255 inclusive specifes a time in
minutes after which the line will be disconnected if no session is open.
The follow…

Integer32r/w

.1.3.6.1.4.1.164.8.4.1.1.1.3

pktSwchLapbSegmentSizeS

This value is for the use of billing information. The value can be no larger than the maximum
packet size.

Integer32r/w

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

.1.3.6.1.4.1.164.8.4.1.1.1.4

pktSwchLapbXIDS

When this parameter is different than zero, this lapb is configured
as a V25 bis dialed link. This is the XID entry Index which this dialed link is
associated with.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.4.1.1.1.5

pktSwchLapbAckCounterS

This object defines how many frames will be received on the link
before the PS will send Acknowledge (RR frame).
It is used for Piggy Back Acknowledge (ack within the info frames)
and saves traffic on the line.
Default …

Integer32r/w

.1.3.6.1.4.1.164.8.4.1.1.1.6

pktSwchLapbAckTimerS

The Ack Timer defines the maximum time in seconds that the device
will wait before sending RR acknowledgment on the received frames.
It is used for Piggy Back Acknowledge (ack within the info frames)
and saves traffic o…

Integer32r/w

.1.3.6.1.4.1.164.8.4.1.1.1.7

pktSwchLapbATable

table

.1.3.6.1.4.1.164.8.4.1.2 · 1 row entry · 18 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchLapbATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchLapbATable'

The Lapb Table includes statistics and configurable objects provided
by the PS that are not included in RFC 1381.

pktSwchLapbAEntry row .1.3.6.1.4.1.164.8.4.1.2.1

Defines the contents of each line in the RAD Lapb Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchLapbLinkNumberA

The link number with which this entry is associated. This value corresponds to
pktSwchPhyInterfaceNumber. There is an entry for each link for which the pktSwchPhyInterfaceProtocol is
X.25 and one entry for each link …

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.4.1.2.1.1

pktSwchLapbInternalClockA

The internal clock speed currently used on this LAPB link.
If external clock is used, the value is 255.

Enumeration

.1.3.6.1.4.1.164.8.4.1.2.1.2

pktSwchLapbLineOptionA

The line option currently used on this link. A value of zero
indicates no options. A value between 1 and 255 inclusive specifes
a time in minutes after which the line will be disconnected if no
session is open. The f…

Integer32

.1.3.6.1.4.1.164.8.4.1.2.1.3

pktSwchLapbSegmentSizeA

The current value of the segment size.

Integer32

Constraints:
range: 0-4095

.1.3.6.1.4.1.164.8.4.1.2.1.4

pktSwchLapbLineProtocol

This is the lower level protocol which runs under this lapb interface.

Enumeration

Constraints:
range: 0-4095

.1.3.6.1.4.1.164.8.4.1.2.1.5

pktSwchLapbLowerId

In case of X.25 over Frame-relay this is the lower level link
number.

SNMPv2-SMIInteger32

Constraints:
range: 0-4095

.1.3.6.1.4.1.164.8.4.1.2.1.6

pktSwchLapbXIDA

When this parameter is different than zero, this lapb is configured
as a V25 bis dialed link. This is the XID entry which this dialed link is
associated with.

SNMPv2-SMIInteger32

Constraints:
range: 0-4095

.1.3.6.1.4.1.164.8.4.1.2.1.7

pktSwchLapbTransmittedIFrames

The transmitted I frames on this link.

SNMPv2-SMICounter32

Constraints:
range: 0-4095

.1.3.6.1.4.1.164.8.4.1.2.1.8

pktSwchLapbReceivedIFrames

The received I frames on this link.

SNMPv2-SMICounter32

Constraints:
range: 0-4095

.1.3.6.1.4.1.164.8.4.1.2.1.9

pktSwchLapbNSError

The number of I frames transmitted out of sequence.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.4.1.2.1.10

pktSwchLapbTransmittedRRFrames

The transmitted RR frames on this link.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.4.1.2.1.11

pktSwchLapbReceivedRRFrames

The received RR frames on this link.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.4.1.2.1.12

pktSwchLapbTransmittedRNRFrames

The transmitted RNR frames on this link.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.4.1.2.1.13

pktSwchLapbReceivedRNRFrames

The received RNR frames on this link.

SNMPv2-SMICounter32

Enumerated Values:

1	other
2	x25
3	hdlc
4	sdlc
5	async
6	mpe
7	ip

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.4.1.2.1.14

pktSwchLapbTransmittedFRMRFrames

The transmitted FRMR frames on this link.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.4.1.2.1.15

pktSwchLapbReceivedFRMRFrames

The received FRMR frames on this link.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.4.1.2.1.16

pktSwchLapbAckCounterA

Integer32

.1.3.6.1.4.1.164.8.4.1.2.1.17

pktSwchLapbAckTimerA

Integer32

.1.3.6.1.4.1.164.8.4.1.2.1.18

pktSwchPlpSTable

table

.1.3.6.1.4.1.164.8.4.2.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchPlpSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchPlpSTable'

The Scratch Plp Table includes configurable objects provided by the PS
that are not included in RFC 1382.

pktSwchPlpSEntry row .1.3.6.1.4.1.164.8.4.2.1.1

Defines the contents of each line in the RAD Scratch Plp Table.

Indexes

No indexes recorded

Column	Syntax	OID
pktSwchPlpLinkNumberS The ifIndex of the X.25 interface.	SNMPv2-SMIInteger32 Constraints: `range: 0-99`	`.1.3.6.1.4.1.164.8.4.2.1.1.1`
pktSwchPlpInCallOptionS The in call options for the link. The value is a sum of values (powers of two), where each value in the sum represents an option. The values that may be included in the sum and their meanings are: 0 No options 1 Fast …	SNMPv2-SMIInteger32r/w Constraints: `range: 0-255`	`.1.3.6.1.4.1.164.8.4.2.1.1.2`
pktSwchPlpOutCallOptionS The out call options for the link. The value is a sum of values (powers of two), where each value in the sum represents an option. The values that may be included in the sum and their meanings are: 0 No options 1 Don'…	Integer32r/w Constraints: `range: 0-255`	`.1.3.6.1.4.1.164.8.4.2.1.1.3`
pktSwchPlpCugSubscriptionS The CUG subscription for the link.	Enumerationr/w Constraints: `range: 0-255`	`.1.3.6.1.4.1.164.8.4.2.1.1.4`
pktSwchPlpNUIS This is the NUI group which this Plp is part of.	SNMPv2-SMIInteger32r/w Constraints: `range: 0-7`	`.1.3.6.1.4.1.164.8.4.2.1.1.5`
pktSwchPlpCpyPktSize x25 packet size.	SNMPv2-SMIInteger32r/w Constraints: `range: 0-99`	`.1.3.6.1.4.1.164.8.4.2.1.1.6`
pktSwchPlpCpyWinSize x25 window size.	SNMPv2-SMIInteger32r/w Constraints: `range: 0-99`	`.1.3.6.1.4.1.164.8.4.2.1.1.7`

pktSwchPlpATable

table

.1.3.6.1.4.1.164.8.4.2.2 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchPlpATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchPlpATable'

The Active Plp Table includes objects provided by the PS
that are not included in RFC 1382. It also includes some packet
layer statistics, some of which are defined in RFC 1382, but are
not supported there, as the x25StatTable in RFC 1382 is not supported.

pktSwchPlpAEntry row .1.3.6.1.4.1.164.8.4.2.2.1

Defines the contents of each line in the RAD Active Plp Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchPlpLinkNumberA

The link number with which this entry is associated. This value corresponds to
pktSwchPhyInterfaceNumber. There is an entry for each link for which the pktSwchPhyInterfaceProtocol is
X.25 and one entry for each link …

SNMPv2-SMIInteger32

Enumerated Values:

1	hdlcOverX25
2	hdlcOverFrRel
3	hdlcOverMpe
4	hdlcReg
5	hdlcOverIp

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.4.2.2.1.1

pktSwchPlpInCallOptionA

The current in call options for the link. The value is a sum of values (powers of two),
where each value in the sum represents an option. The values that can be included in
the sum and their meanings are:
0 No options…

SNMPv2-SMIInteger32

Constraints:
range: 0-3

.1.3.6.1.4.1.164.8.4.2.2.1.2

pktSwchPlpOutCallOptionA

The out call options for the link. The value is a sum of values
(powers of two), where each value in the sum represents an
option. The values that may be included in the sum and their
meanings are:
0 No options
1 Don'…

Integer32

Constraints:
range: 1-200

.1.3.6.1.4.1.164.8.4.2.2.1.3

pktSwchPlpCugSubscriptionA

The current CUG subscription for the link.

Enumeration

Enumerated Values:

1	r2400bps
2	r4800bps
3	r9600bps
4	r14400bps
5	r19200bps
6	r38400bps
7	r48Kbps
8	r56Kbps
9	r64Kbps
10	r128Kbps
11	r256Kbps
12	r384Kbps
13	r504Kbps
14	r768Kbps
15	r1008Kbps
16	r1466Kbps
17	r2016Kbps
255	external

.1.3.6.1.4.1.164.8.4.2.2.1.4

pktSwchPlpNUIA

This is the NUI group which this Plp is part of.

SNMPv2-SMIInteger32

Constraints:
range: 0-7

.1.3.6.1.4.1.164.8.4.2.2.1.5

pktSwchStatOutRestarts

The number of remotely initiated (including
provider initiated) restarts experienced by
the PLE excluding the restart associated
with bringing up the PLE interface. This
only counts restarts received when the PLE
alrea…

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.4.2.2.1.6

pktSwchCugSTable

table

.1.3.6.1.4.1.164.8.4.4.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchCugSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchCugSTable'

The Scratch Cug Table lists the Closed User Groups defined to each
X.25 link.

pktSwchCugSEntry row .1.3.6.1.4.1.164.8.4.4.1.1

Defines the contents of each line in the Scratch RAD Cug Table.

Indexes

No indexes recorded

Column	Syntax	OID
pktSwchCugLinkNumberS The link number with which this entry is associated. This value corresponds to pktSwchPhyInterfaceNumber. There is an entry for each link for which the pktSwchPhyInterfaceProtocol is X.25 if the link has CUG options …	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.8.4.4.1.1.1`
pktSwchCugIndexS The index of the CUG for a specific link. The lowest indexed CUG is the preferential CUG.	SNMPv2-SMIInteger32 Constraints: `range: 0-99`	`.1.3.6.1.4.1.164.8.4.4.1.1.2`
pktSwchCugNumberS The CUG number for this entry.	SNMPv2-SMIInteger32r/w Constraints: `range: 0-255`	`.1.3.6.1.4.1.164.8.4.4.1.1.3`
pktSwchCugStatus The status of this CUG table entry. The choices are those defined in the SNMPv2 Textual Conventions for RowStatus. This will allow easy replacement of the INTEGER syntax with the RowStatus textual convention SYNTAX.	Enumerationr/w Constraints: `range: 0-255`	`.1.3.6.1.4.1.164.8.4.4.1.1.4`

pktSwchCugATable

table

.1.3.6.1.4.1.164.8.4.4.2 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchCugATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchCugATable'

The Active Cug Table lists the active Closed User Groups defined
to each X.25 link.

pktSwchCugAEntry row .1.3.6.1.4.1.164.8.4.4.2.1

Defines the contents of each line in the Active RAD Cug Table.

Indexes

No indexes recorded

Column	Syntax	OID
pktSwchCugLinkNumberA The link number with which this entry is associated. This value corresponds to pktSwchPhyInterfaceNumber. There is an entry for each link for which the pktSwchPhyInterfaceProtocol is X.25 if the link has CUG options …	SNMPv2-SMIInteger32 Constraints: `range: 0-99`	`.1.3.6.1.4.1.164.8.4.4.2.1.1`
pktSwchCugIndexA The index of the CUG for a specific link. The lowest indexed CUG is the preferential CUG.	SNMPv2-SMIInteger32 Constraints: `range: 0-99`	`.1.3.6.1.4.1.164.8.4.4.2.1.2`
pktSwchCugNumberA The CUG number for this entry.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.8.4.4.2.1.3`

pktSwchLogChAssTable

table

.1.3.6.1.4.1.164.8.4.5.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchLogChAssTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchLogChAssTable'

These objects contain information about the
channel number configuration in an X.25 PLE.
These values are the configured values.
changes in these values after the interface
has started may not be reflected in the
operating PLE.

pktSwchLogChAssEntry row .1.3.6.1.4.1.164.8.4.5.1.1

Entries of pktSwchLogChAssTable.

Indexes

No indexes recorded

Column Syntax OID

pktSwchLogChAssIndex

The ifIndex value for the X.25 Interface.

RFC1381-MIBIfIndexType

Constraints:
range: 0-3

.1.3.6.1.4.1.164.8.4.5.1.1.1

pktSwchLogChAssLIC

Lowest Incoming channel.

Integer32

Constraints:
range: 1-200

.1.3.6.1.4.1.164.8.4.5.1.1.2

pktSwchLogChAssHIC

Highest Incoming channel. A value of zero
indicates no channels in this range.

Integer32

Enumerated Values:

1	r2400bps
2	r4800bps
3	r9600bps
4	r14400bps
5	r19200bps
6	r38400bps
7	r48Kbps
8	r56Kbps
9	r64Kbps
10	r128Kbps
11	r256Kbps
12	r384Kbps
13	r504Kbps
14	r768Kbps
15	r1008Kbps
16	r1466Kbps
17	r2016Kbps
255	external

.1.3.6.1.4.1.164.8.4.5.1.1.3

pktSwchLogChAssLTC

Lowest Two-way channel.

Integer32

Constraints:
range: 0-7

.1.3.6.1.4.1.164.8.4.5.1.1.4

pktSwchLogChAssHTC

Highest Two-way channel. A value of zero
indicates no channels in this range.

Integer32

Enumerated Values:

1	disconnect
2	connect
3	pvc

.1.3.6.1.4.1.164.8.4.5.1.1.5

pktSwchLogChAssLOC

Lowest outgoing channel.

Integer32

Enumerated Values:

1	busy
2	overflow
255	noStatus

.1.3.6.1.4.1.164.8.4.5.1.1.6

pktSwchLogChAssHOC

Highest outgoing channel. A value of zero
indicates no channels in this range.

Integer32

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.8.4.5.1.1.7

pktSwchLogChPartnerTable

table

.1.3.6.1.4.1.164.8.4.5.2 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchLogChPartnerTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchLogChPartnerTable'

These objects contain information about the
partner channel number configuration in an X.25 PLE.
These values are the configured values.
changes in these values after the interfaces
has started may not be reflected in the
operating PLE.

pktSwchLogChPartnerEntry row .1.3.6.1.4.1.164.8.4.5.2.1

Entries of pktSwchLogChPartnerTable.

Indexes

No indexes recorded

Column	Syntax	OID
pktSwchLogChPartnerIfIndex The ifIndex value for the Lapb Interface.	RFC1381-MIBIfIndexType Type Constraints: `range: 1..2147483647`	`.1.3.6.1.4.1.164.8.4.5.2.1.1`
pktSwchLogChPartnerLcIndex The Index value for the LCN.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.8.4.5.2.1.2`
pktSwchLogChPartnerProtocol The protocol of the partner.	Enumeration	`.1.3.6.1.4.1.164.8.4.5.2.1.3`
pktSwchLogChPartnerOpIfIndex The ifIndex value for the partner Lapb Interface.	RFC1381-MIBIfIndexType Type Constraints: `range: 1..2147483647`	`.1.3.6.1.4.1.164.8.4.5.2.1.4`
pktSwchLogChPartnerOpLcIndex The Index value for the partner LCN.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.8.4.5.2.1.5`

pktSwchHdlcSTable

table

.1.3.6.1.4.1.164.8.5.1 · 1 row entry · 16 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchHdlcSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchHdlcSTable'

The Scratch Hdlc Table contains configuration information for HDLC links

pktSwchHdlcSEntry row .1.3.6.1.4.1.164.8.5.1.1

Defines the contents of each line in the RAD Hdlc Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchHdlcLinkNumberS

The link number with which this entry is associated. This value
corresponds to pktSwchPhyInterfaceNumber. There is an entry for
each link for which the pktSwchPhyInterfaceProtocol is HDLC.

SNMPv2-SMIInteger32

Enumerated Values:

1	disconnect
2	connect

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.5.1.1.1

pktSwchHdlcDestAddrS

The destination address. It defines the X.25 address on the remote
device.

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.5.1.1.2

pktSwchHdlcDestSubAddrS

The destination subaddress. It defines the synchronous link subaddress
on the remote device.

Integer32r/w

.1.3.6.1.4.1.164.8.5.1.1.3

pktSwchHdlcRedialTimeoutS

The time interval in seconds between two consecutive connect
operations retries.

Integer32r/w

.1.3.6.1.4.1.164.8.5.1.1.4

pktSwchHdlcRedialRetriesS

This defines how many times the call operation is repeated if the
call request has failed.

Integer32r/w

.1.3.6.1.4.1.164.8.5.1.1.5

pktSwchHdlcInactivityS

The amount of time in minutes of inactivity that will cause the
session to disconnect.

Integer32r/w

Constraints:
range: 0-12

.1.3.6.1.4.1.164.8.5.1.1.6

pktSwchHdlcX25FacilitiesS

This specifies the X.25 facilities. The value is a sum of values
(powers of two), where each value in the sum represents an option.
The values that may be included in the sum and their meanings are:
0 No options
1 Pa…

Integer32r/w

Enumerated Values:

1	user
2	network
3	both

.1.3.6.1.4.1.164.8.5.1.1.7

pktSwchHdlcLocalSubaddr1S

The first local subaddress.

Integer32r/w

Constraints:
range: 0-39

.1.3.6.1.4.1.164.8.5.1.1.8

pktSwchHdlcLocalSubaddr2S

The secondary local subaddress.

Integer32r/w

Constraints:
range: 1-40

.1.3.6.1.4.1.164.8.5.1.1.9

pktSwchHdlcDestDlciS

The local DLCI which is used for HDLC encapsulation over Frame Relay.
Range: 16...991

SNMPv2-SMIInteger32r/w

Constraints:
range: 1-500

.1.3.6.1.4.1.164.8.5.1.1.10

pktSwchHdlcDestPortS

The local port that is used for HDLC encapsulation over Frame Relay.
Range: 1...12

SNMPv2-SMIInteger32r/w

Constraints:
range: 0-499

.1.3.6.1.4.1.164.8.5.1.1.11

pktSwchHdlcProtocolS

The HDLC protocol type.

Enumerationr/w

Constraints:
range: 1-500

.1.3.6.1.4.1.164.8.5.1.1.12

pktSwchHdlcFlowContOptionsS

This specifies the type of flow control of the HDLC link. The value
is a sum of values (powers of two), where each value in the sum
represents an option. The values that may be included in the sum and
their meanings a…

Integer32r/w

Enumerated Values:

1	r2400bps
2	r4800bps
3	r9600bps
4	r14400bps
5	r19200bps
6	r38400bps
7	r48Kbps
8	r56Kbps
9	r64Kbps
10	r128Kbps
11	r256Kbps
12	r384Kbps
13	r504Kbps
14	r768Kbps
15	r1008Kbps
16	r1466Kbps
17	r2016Kbps
255	external

.1.3.6.1.4.1.164.8.5.1.1.13

pktSwchHdlcBufferFlowControlS

The number of buffers that will be allocated for the HDLC link. Default value is 10

Integer32r/w

Enumerated Values:

1	nrz
2	nrzi

.1.3.6.1.4.1.164.8.5.1.1.14

pktSwchHdlcInternalClockS

The baud rate of the internal clock.

Enumerationr/w

Enumerated Values:

1	two-octets
2	three-octets
3	four-octets
4	four-octets-nomanag

.1.3.6.1.4.1.164.8.5.1.1.15

pktSwchHdlcNrzModeS

The data encoding format.
The value is a sum of values (powers of two), where each
value in the sum represents an option.
The values that may be included in the sum and their
meanings are:
0 NRZ
1 NRZI
2 Tra…

Integer32r/w

Enumerated Values:

2	no-Detect
3	linkFailure-Detect

.1.3.6.1.4.1.164.8.5.1.1.16

pktSwchHdlcATable

table

.1.3.6.1.4.1.164.8.5.2 · 1 row entry · 23 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchHdlcATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchHdlcATable'

The Active Hdlc Table contains active configuration information for HDLC links

pktSwchHdlcAEntry row .1.3.6.1.4.1.164.8.5.2.1

Defines the contents of each line in the RAD Hdlc Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchHdlcLinkNumberA

The link number with which this entry is associated. This value corresponds to
pktSwchPhyInterfaceNumber. There is an entry for each link for which the pktSwchPhyInterfaceProtocol is
HDLC.

SNMPv2-SMIInteger32

Enumerated Values:

2	noOption
3	dds4800bps
4	dds9600bps
5	dds19200bps
6	dds56000bos

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.5.2.1.1

pktSwchHdlcDestAddrA

The destination address. It defines the X.25 address on the remote device.

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.5.2.1.2

pktSwchHdlcDestSubAddrA

The destination subaddress. It defines the synchronous link subaddress on the remote
device.

Integer32

.1.3.6.1.4.1.164.8.5.2.1.3

pktSwchHdlcRedialTimeoutA

The time interval in seconds between two consecutive connect operations retries.

Integer32

.1.3.6.1.4.1.164.8.5.2.1.4

pktSwchHdlcRedialRetriesA

This defines how many times the call operation is repeated if the call request has failed.

Integer32

Constraints:
range: 0-12

.1.3.6.1.4.1.164.8.5.2.1.5

pktSwchHdlcInactivityA

The amount of time in minutes of inactivity that will cause the
session to disconnect.

Integer32

Enumerated Values:

1	user
2	network
3	both

.1.3.6.1.4.1.164.8.5.2.1.6

pktSwchHdlcX25FacilitiesA

This specifies the X.25 facilities. The value is a sum of values (powers of two), where each
value in the sum represents an option. The values that may be included in the sum and
their meanings are:
0 No options
1 Pac…

Integer32

Constraints:
range: 0-39

.1.3.6.1.4.1.164.8.5.2.1.7

pktSwchHdlcLocalSubaddr1A

The first local subaddress.

Integer32

Constraints:
range: 1-40

.1.3.6.1.4.1.164.8.5.2.1.8

pktSwchHdlcLocalSubaddr2A

The secondary local subaddress.

Integer32

Constraints:
range: 1-500

.1.3.6.1.4.1.164.8.5.2.1.9

pktSwchHdlcDestDlciA

The local DLCI which is used for HDLC encapsulation over Frame Relay.

SNMPv2-SMIInteger32

Constraints:
range: 0-499

.1.3.6.1.4.1.164.8.5.2.1.10

pktSwchHdlcDestPortA

The local port that is used for HDCL encapsulation over Frame Relay.

SNMPv2-SMIInteger32

Constraints:
range: 0-500

.1.3.6.1.4.1.164.8.5.2.1.11

pktSwchHdlcProtocolA

The HDLC protocol type.

Enumeration

Enumerated Values:

1	r2400bps
2	r4800bps
3	r9600bps
4	r14400bps
5	r19200bps
6	r38400bps
7	r48Kbps
8	r56Kbps
9	r64Kbps
10	r128Kbps
11	r256Kbps
12	r384Kbps
13	r504Kbps
14	r768Kbps
15	r1008Kbps
16	r1466Kbps
17	r2016Kbps
255	external

.1.3.6.1.4.1.164.8.5.2.1.12

pktSwchHdlcFlowContOptionsA

This specifies the type of flow control of the HDLC link. The value is a sum of values
(powers of two), where each value in the sum represents an option. The values that may
be included in the sum and their meanings a…

Integer32

Enumerated Values:

1	nrz
2	nrzi

.1.3.6.1.4.1.164.8.5.2.1.13

pktSwchHdlcBufferFlowControlA

The number of buffers that will be allocated for the HDLC link.

Integer32

Constraints:
range: 5-30

.1.3.6.1.4.1.164.8.5.2.1.14

pktSwchHdlcInternalClockA

The baud rate of the internal clock.

Enumeration

Constraints:
range: 1-255

.1.3.6.1.4.1.164.8.5.2.1.15

pktSwchHdlcNrzModeA

Integer32

Constraints:
range: 1-10

.1.3.6.1.4.1.164.8.5.2.1.16

pktSwchHdlcConnStatus

The status of the Hdlc session.

Enumeration

Constraints:
range: 1-10

.1.3.6.1.4.1.164.8.5.2.1.17

pktSwchHdlcSpecialStatus

The status of the Hdlc link.

Enumeration

Enumerated Values:

1	two-octets
2	three-octets
3	four-octets
4	four-octets-nomanag

.1.3.6.1.4.1.164.8.5.2.1.18

pktSwchHdlcCtsStatus

The CTS status.

Enumeration

Enumerated Values:

2	no-Detect
3	linkFailure-Detect

.1.3.6.1.4.1.164.8.5.2.1.19

pktSwchHdlcRunningX25Lcn

The format of the string is ifIndex:LCN

SNMPv2-TCDisplayString

Enumerated Values:

2	no
3	yes

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.5.2.1.20

pktSwchHdlcRunningDlci

The format of the string is ifIndex:DLCI

SNMPv2-TCDisplayString

Enumerated Values:

2	swControl
3	hwControl

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.5.2.1.21

pktSwchHdlcMaxBuffToNet

The maximum number of buffers above which Flow Control is enabled

SNMPv2-SMIInteger32

Enumerated Values:

2	noOption
3	dds4800bps
4	dds9600bps
5	dds19200bps
6	dds56000bos

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.5.2.1.22

pktSwchHdlcBuffToNet

The number of buffers waiting for transmission.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.5.2.1.23

pktSwchStmTable

table

.1.3.6.1.4.1.164.8.7 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchStmTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchStmTable'

The STM table contains information for STM links

pktSwchStmEntry row .1.3.6.1.4.1.164.8.7.1

Defines the contents of each line in the RAD STM Table.

Indexes

No indexes recorded

Column	Syntax	OID
pktSwchStmLinkNumber The link number with which this entry is associated. This value corresponds to pktSwchPhyInterfaceNumber. There is an entry for each link whose pktSwchPhyInterfaceProtocol is STM 4, 8, 16, or 24.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.8.7.1.1`
pktSwchStmInternalClockS The baud rate of the internal clock.	Enumerationr/w	`.1.3.6.1.4.1.164.8.7.1.2`
pktSwchStmInternalClockA The current baud rate of the internal clock.	Enumeration	`.1.3.6.1.4.1.164.8.7.1.3`
pktSwchStmConn The connectivity status of the STM interface.	Enumeration	`.1.3.6.1.4.1.164.8.7.1.4`
pktSwchStmSyncLoss The counter for sync loss.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.8.7.1.5`

pktSwchFrSTable

table

.1.3.6.1.4.1.164.8.8.2 · 1 row entry · 15 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchFrSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchFrSTable'

The Frame Relay Scratch Table includes the scratch values of
configurable objects provided by the PS that are not included
in RFC 1315.

pktSwchFrSEntry row .1.3.6.1.4.1.164.8.8.2.1

Defines the contents of each line in the RAD PS Frame Relay
Scratch Table.

Indexes

No indexes recorded

Column	Syntax	OID
pktSwchFrIfIndexS This is the ifIndex of the frame relay port.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.8.8.2.1.1`
pktSwchFrMaintProtS This defines what maintenance protocol is running over this port. 0 - No maintenance protocol. 1 - ANSI PVC maintenance protocol running on DLCI number 0. 2 - LMI maintenance protocol running on DLCI number 1023. 4 - IT…	Integer32r/w	`.1.3.6.1.4.1.164.8.8.2.1.2`
pktSwchFrMaintModeS This defines the mode of maintenance protocol running over this port.	Enumerationr/w	`.1.3.6.1.4.1.164.8.8.2.1.3`
pktSwchFrRxPoolRedLineS When the number of empty receive buffers at the port reaches this figure (of frames),the port receiver is congested. This field value should be less than the Rx pool OK field.	Integer32r/w	`.1.3.6.1.4.1.164.8.8.2.1.4`
pktSwchFrRxPoolOkS Clear the receive congestion condition when the number of empty receive buffers at the port reaches this figure. This value (of frames) should be greater than the Rx pool red line.	Integer32r/w	`.1.3.6.1.4.1.164.8.8.2.1.5`
pktSwchFrTxPoolRedLineS When the number of frames awaiting transmission reaches this figure, the port transmitter is congested. This field value should be greater than the Tx pool OK field.	Integer32r/w	`.1.3.6.1.4.1.164.8.8.2.1.6`
pktSwchFrTxPoolOkS Clear the transmit congestion condition when the number of frames awaiting transmission at the port reaches this figure. This value (of frames) should be less than the Tx pool red line.	Integer32r/w	`.1.3.6.1.4.1.164.8.8.2.1.7`
pktSwchFrTxCeilingS The maximum allowable transmit pool for this port.	Integer32r/w	`.1.3.6.1.4.1.164.8.8.2.1.8`
pktSwchFrInternalClockS The baud rate of the internal clock.	Enumerationr/w	`.1.3.6.1.4.1.164.8.8.2.1.9`
pktSwchFrNrzModeS The data encoding format.	Enumerationr/w	`.1.3.6.1.4.1.164.8.8.2.1.10`
pktSwchFrDlciHeaderModeS Dlci Header length for this FR port. Option 4 means that there will be no management Dlci in the range of 1024 to 8388607. The management Dlci will be in the range of 0-15 or 991-1023. Default value: 1.	Enumerationr/w	`.1.3.6.1.4.1.164.8.8.2.1.11`
pktSwchFrDcdLinkFailureS Link Failure Detection by DCD. If Link Failure detection by DCD is on - (3), when the DCD is down, the FR SW will detect it and change the FR link status from UP to DOWN. A trap of LINK DOWN will be sent to the NMS. Def…	Enumerationr/w	`.1.3.6.1.4.1.164.8.8.2.1.12`
pktSwchFrTxIdlesS This parameter shows whether the PS will Transmit Idles between frames and control the RTS pin. Default: no(2).	Enumerationr/w	`.1.3.6.1.4.1.164.8.8.2.1.13`
pktSwchFrOperationModeS When H/W Control is configured, the SCC H/W will detect the change in the DCD or CTS signals and Start or Stop transmission automatically. When S/W Control is configured the S/W will decide when to start or stop the tra…	Enumerationr/w	`.1.3.6.1.4.1.164.8.8.2.1.14`
pktSwchFrPhysInterfOptionsS This is the physical interface. Note that the DDS physical interface H/W does not exist in the FPS-8. It is relevant for other PS devices only. For FPS-8 only the default (noOption) should be used. Default: (2).	Enumerationr/w	`.1.3.6.1.4.1.164.8.8.2.1.15`

pktSwchFrATable

table

.1.3.6.1.4.1.164.8.8.3 · 1 row entry · 19 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchFrATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchFrATable'

The Frame Relay Active Table includes statistics and the active values of configurable
objects provided by the PS that are not included in RFC 1315.

pktSwchFrAEntry row .1.3.6.1.4.1.164.8.8.3.1

Defines the contents of each line in the RAD PS Frame Relay Active Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchFrIfIndexA

This is the ifIndex of the frame relay port.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.8.3.1.1

pktSwchFrMaintProtA

This defines what maintenance protocol is running over this port.
0 - No maintenance protocol.
1 - ANSI PVC maintenance protocol running on DLCI number 0.
2 - LMI maintenance protocol running on DLCI number 1023.
4 - IT…

Integer32

.1.3.6.1.4.1.164.8.8.3.1.2

pktSwchFrMaintModeA

This defines the mode of maintenance protocol running over this port.

Enumeration

.1.3.6.1.4.1.164.8.8.3.1.3

pktSwchFrRxPoolRedLineA

When the number of empty receive buffers at the port reaches this figure (of frames),
the port receiver is congested. This field value should be less than the Rx pool OK field.

Integer32

Enumerated Values:

1	x25
2	none
3	hdlc
4	async
5	multiPoint
6	rfc1490

.1.3.6.1.4.1.164.8.8.3.1.4

pktSwchFrRxPoolOkA

Clear the receive congestion condition when the number of empty receive buffers at the port
reaches this figure. This value (of frames) should be greater than the Rx pool red line.

Integer32

.1.3.6.1.4.1.164.8.8.3.1.5

pktSwchFrTxPoolRedLineA

When the number of frames awaiting transmission reaches this figure,
the port transmitter is congested. This field value should be greater than the Tx pool OK field.

Integer32

.1.3.6.1.4.1.164.8.8.3.1.6

pktSwchFrTxPoolOkA

Clear the transmit congestion condition when the number of frames awaiting transmission
at the port reaches this figure. This value (of frames) should be less than the Tx pool red line.

Integer32

Constraints:
range: 0-10

.1.3.6.1.4.1.164.8.8.3.1.7

pktSwchFrTxCeilingA

The maximum allowable transmit pool for this port.

Integer32

Constraints:
range: 0-65000

.1.3.6.1.4.1.164.8.8.3.1.8

pktSwchFrInternalClockA

The baud rate of the internal clock.

Enumeration

Constraints:
range: 0-65000

.1.3.6.1.4.1.164.8.8.3.1.9

pktSwchFrNrzModeA

The data encoding format.

Enumeration

Constraints:
range: 0-10

.1.3.6.1.4.1.164.8.8.3.1.10

pktSwchFrDlcmiPollingInterval

This is the number of seconds between succes-
sive status enquiry messages.

Integer32

Constraints:
range: 0-65000

.1.3.6.1.4.1.164.8.8.3.1.11

pktSwchFrDlcmiFullEnquiryInterval

Number of status enquiry intervals that pass
before issuance of a full status enquiry mes-
sage.

Integer32

Constraints:
range: 0-65000

.1.3.6.1.4.1.164.8.8.3.1.12

pktSwchFrDlcmiErrorThreshold

This is the maximum number of unanswered
Status Enquiries the equipment shall accept be-
fore declaring the interface down.

Integer32

Constraints:
range: 1-200

.1.3.6.1.4.1.164.8.8.3.1.13

pktSwchFrDlcmiMonitoredEvents

This is the number of status polling intervals
over which the error threshold is counted. For
example, if within 'MonitoredEvents' number of
events the station receives 'ErrorThreshold'
number of errors, the interf…

Integer32

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

.1.3.6.1.4.1.164.8.8.3.1.14

pktSwchFrDlciHeaderModeA

Dlci Header length for this FR port. Option 4 means that there
will be no management Dlci in the range of 1024 to 8388607.
The management Dlci will be in the range of 0-15 or 991-1023.
Default value: 1.

Enumeration

Constraints:
range: 0-8388607

.1.3.6.1.4.1.164.8.8.3.1.15

pktSwchFrDcdLinkFailureA

Link Failure Detection by DCD.
If Link Failure detection by DCD is on - (3), when the DCD is
down, the FR SW will detect it and change the FR link status
from UP to DOWN. A trap of LINK DOWN will be sent to the NMS.
Def…

Enumeration

Constraints:
range: 1-4

.1.3.6.1.4.1.164.8.8.3.1.16

pktSwchFrTxIdlesA

This parameter shows whether the PS will Transmit Idles between
frames and control the RTS pin.
Default: no(2).

Enumeration

Constraints:
range: 0-200

.1.3.6.1.4.1.164.8.8.3.1.17

pktSwchFrOperationModeA

When H/W Control is configured, the SCC H/W will detect the change in the
DCD or CTS signals and Start or Stop transmission automatically.
When S/W Control is configured the S/W will decide when to start or stop
the tra…

Enumeration

.1.3.6.1.4.1.164.8.8.3.1.18

pktSwchFrPhysInterfOptionsA

This is the physical interface.
Note that the DDS physical interface H/W does not exist in the FPS-8.
It is relevant for other PS devices only.
For FPS-8 only the default (noOption) should be used.
Default: (2).

Enumeration

.1.3.6.1.4.1.164.8.8.3.1.19

pktSwchFrIfTable

table

.1.3.6.1.4.1.164.8.8.4 · 1 row entry · 24 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchFrIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchFrIfTable'

The Frame Relay Active Port Table includes statistics and configurable objects
provided by the PS  that are not included in RFC 1315.

pktSwchFrIfEntry row .1.3.6.1.4.1.164.8.8.4.1

Defines the contents of each line in the RAD PS Frame Relay Port Active Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchFrIfTxBytes

The number of Tx bytes.

SNMPv2-SMICounter32

Enumerated Values:

1	x25
2	none
3	hdlc
4	async
5	multiPoint
6	rfc1490

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.8.4.1.1

pktSwchFrIfRxBytes

The number of Rx bytes.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.8.4.1.2

pktSwchFrIfTxCongDiscards

The number of frames discarded because of Tx congestion.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.8.4.1.3

pktSwchFrIfDeTxFrames

The number of DE Tx frames.

SNMPv2-SMICounter32

Constraints:
range: 0-10

.1.3.6.1.4.1.164.8.8.4.1.4

pktSwchFrIfDeRxFrames

The number of DE Rx frames.

SNMPv2-SMICounter32

Constraints:
range: 0-65000

.1.3.6.1.4.1.164.8.8.4.1.5

pktSwchFrIfFecnTxFrames

The number of FECN Tx frames.

SNMPv2-SMICounter32

Constraints:
range: 0-65000

.1.3.6.1.4.1.164.8.8.4.1.6

pktSwchFrIfFecnRxFrames

The number of FECN Tx frames.

SNMPv2-SMICounter32

Constraints:
range: 0-10

.1.3.6.1.4.1.164.8.8.4.1.7

pktSwchFrIfBecnTxFrames

The number of BECN Tx frames.

SNMPv2-SMICounter32

Constraints:
range: 0-65000

.1.3.6.1.4.1.164.8.8.4.1.8

pktSwchFrIfBecnRxFrames

The number of BECN Tx frames.

SNMPv2-SMICounter32

Constraints:
range: 0-65000

.1.3.6.1.4.1.164.8.8.4.1.9

pktSwchFrIfCommRateViolTxFrames

The number of Tx committed rate violations in number of frames.

SNMPv2-SMICounter32

Constraints:
range: 1-200

.1.3.6.1.4.1.164.8.8.4.1.10

pktSwchFrIfCommRateViolRxFrames

The number of Rx committed rate violations in number of frames.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.8.4.1.11

pktSwchFrIfExcessRateViolTxFrames

The number of Tx excess rate violations in number of frames.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.8.4.1.12

pktSwchFrIfExcessRateViolRxFrames

The number of Rx excess rate violations in number of frames.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.8.4.1.13

pktSwchFrIfBuffersInTxPool

The number of buffers waiting for transmission.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.8.4.1.14

pktSwchFrIfFreeBuffersInRxPool

The number of free buffers in the Rx pool.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.8.4.1.15

pktSwchFrIfLmiTxFrames

The number of LMI Tx Frames.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.8.4.1.16

pktSwchFrIfLmiRxFrames

The number of LMI Rx Frames.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.8.4.1.17

pktSwchFrIfAnsiTxFrames

The number of ANSI Tx Frames.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.8.4.1.18

pktSwchFrIfAnsiRxFrames

The number of ANSI Rx Frames.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.8.4.1.19

pktSwchFrIfCllmTxFrames

The number of CLLM Tx Frames.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.8.4.1.20

pktSwchFrIfCllmRxFrames

The number of CLLM Rx Frames.

SNMPv2-SMICounter32

Enumerated Values:

1	new
2	noState

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.8.4.1.21

pktSwchFrIfTxCongestions

The number of Tx congestions.

SNMPv2-SMICounter32

Constraints:
range: 0-8388607

.1.3.6.1.4.1.164.8.8.4.1.22

pktSwchFrIfRxCongestions

The number of Rx congestions.

SNMPv2-SMICounter32

Constraints:
range: 1-4

.1.3.6.1.4.1.164.8.8.4.1.23

pktSwchFrIfTotDlciNumber

The total number of DLCIs defined.

SNMPv2-SMIInteger32

Constraints:
range: 0-200

.1.3.6.1.4.1.164.8.8.4.1.24

pktSwchFrCircuitSTable

table

.1.3.6.1.4.1.164.8.8.5 · 1 row entry · 16 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchFrCircuitSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchFrCircuitSTable'

The Frame Relay Scratch Circuit Table includes configurable objects
provided by the PS  that are not included in RFC 1315.

pktSwchFrCircuitSEntry row .1.3.6.1.4.1.164.8.8.5.1

Defines the contents of each line in the RAD PS Frame Relay
Circuit Scratch Table.

Indexes

pktSwchFrFunnelIndexS

Column Syntax OID

pktSwchFrCircuitIfIndexS

This is the ifIndex of the circuit, according to RFC 1573.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.8.5.1.1

pktSwchFrCircuitIndexS

This Index is the DLCI of the circuit.

SNMPv2-SMIInteger32

Constraints:
range: 0-256

.1.3.6.1.4.1.164.8.8.5.1.2

pktSwchFrCircuitDestProtS

The protocol encapsulation, if any, on this DLCI.
The MPE protocol is a proprietary RAD protocol that enables
a generic HDLC device to have multiple connections over X.25
or Frame Relay.

Enumerationr/w

Constraints:
range: 0-256

.1.3.6.1.4.1.164.8.8.5.1.3

pktSwchFrCircuitDestIdS

If the DLCI destination protocol is none or async, this field
has a value of an existing DLCI or async channel, respectively.
Otherwise, a value of zero is used.

SNMPv2-TCDisplayStringr/w

Constraints:
range: 0-65000

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.8.5.1.4

pktSwchFrCircuitBackIdS

The backup DLCI which is used when the current DLCI goes inactive.
The destination protocol and destination id are the same as in the
current DLCI

SNMPv2-TCDisplayStringr/w

Constraints:
range: 0-65000

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.8.5.1.5

pktSwchFrCircuitTxCirIntervalS

The Tx CIR interval in 1/10 seconds.

Integer32r/w

Constraints:
range: 0-10

.1.3.6.1.4.1.164.8.8.5.1.6

pktSwchFrCircuitTxCommittedS

The Tx committed rate in bytes per interval.

Integer32r/w

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

.1.3.6.1.4.1.164.8.8.5.1.7

pktSwchFrCircuitTxExcessS

The Tx excess in bytes per interval.

Integer32r/w

.1.3.6.1.4.1.164.8.8.5.1.8

pktSwchFrCircuitRxCirIntervalS

The Rx CIR interval in 1/10 seconds.

Integer32r/w

.1.3.6.1.4.1.164.8.8.5.1.9

pktSwchFrCircuitRxCommittedS

The Rx committed rate in bytes per interval.

Integer32r/w

.1.3.6.1.4.1.164.8.8.5.1.10

pktSwchFrCircuitRxExcessS

The Rx excess in bytes per interval.

Integer32r/w

Constraints:
range: 0-256

.1.3.6.1.4.1.164.8.8.5.1.11

pktSwchFrCircuitFunnelIdS

The funnel ID.

Integer32r/w

Constraints:
range: 0-256

.1.3.6.1.4.1.164.8.8.5.1.12

pktSwchFrCircuitStatusS

The status of the circuit row in the Table.

Enumerationr/w

Constraints:
range: 0-65000

.1.3.6.1.4.1.164.8.8.5.1.13

pktSwchFrCircuitExtendedDlciS

The no. of the DLCI represented in 23 bits.

Integer32

Constraints:
range: 0-65000

.1.3.6.1.4.1.164.8.8.5.1.14

pktSwchFrCircuitTxPriorityS

DLCI TX Priority level. The levels are defined in the
pktSwchTxPriorityTable

Integer32r/w

Constraints:
range: 0-10

.1.3.6.1.4.1.164.8.8.5.1.15

pktSwchFrCircuitIsdnRoutIdS

ISDN destination. ID in the ISDN routing table containing
the outgoing ISDN address for this DLCI.

Default value: 0 for no ISDN routing ID.

Integer32r/w

.1.3.6.1.4.1.164.8.8.5.1.16

pktSwchFrCircuitATable

table

.1.3.6.1.4.1.164.8.8.6 · 1 row entry · 26 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchFrCircuitATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchFrCircuitATable'

The Frame Relay Active Circuit Table includes statistics and configurable objects
provided by the PS  that are not included in RFC 1315.

pktSwchFrCircuitAEntry row .1.3.6.1.4.1.164.8.8.6.1

Defines the contents of each line in the RAD PS Frame Relay Circuit Active Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchFrCircuitIfIndexA

This is the ifIndex of the circuit, according to RFC 1573.

SNMPv2-SMIInteger32

Constraints:
range: 0-8388607

.1.3.6.1.4.1.164.8.8.6.1.1

pktSwchFrCircuitIndexA

This Index is the DLCI of the circuit.

SNMPv2-SMIInteger32

Constraints:
range: 0-1023

.1.3.6.1.4.1.164.8.8.6.1.2

pktSwchFrCircuitDestProtA

The protocol encapsulation, if any, on this DLCI.
The MPE protocol is a proprietary RAD protocol that enables
a generic HDLC device to have multiple connections over X.25
or Frame Relay.

Enumeration

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

.1.3.6.1.4.1.164.8.8.6.1.3

pktSwchFrCircuitDestIdA

If the DLCI destination protocol is none or async, this field
has a value of an existing DLCI or async channel, respectively.
Otherwise, a value of zero is used.

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.8.6.1.4

pktSwchFrCircuitBackIdA

The backup DLCI which is used when the current DLCI goes inactive.
The destination protocol and destination id are the same as in the
current DLCI

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.8.6.1.5

pktSwchFrCircuitTxCirIntervalA

The Tx CIR interval in 1/10 seconds.

Integer32

.1.3.6.1.4.1.164.8.8.6.1.6

pktSwchFrCircuitTxCommittedA

The Tx committed rate in bytes per interval.

Integer32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.8.6.1.7

pktSwchFrCircuitTxExcessA

The Tx excess in bytes per interval.

Integer32

Constraints:
range: 0-7

.1.3.6.1.4.1.164.8.8.6.1.8

pktSwchFrCircuitRxCirIntervalA

The Rx CIR interval in 1/10 seconds.

Integer32

Constraints:
range: 1-99

.1.3.6.1.4.1.164.8.8.6.1.9

pktSwchFrCircuitRxCommittedA

The Rx committed rate in bytes per interval.

Integer32

Constraints:
range: 1-99

.1.3.6.1.4.1.164.8.8.6.1.10

pktSwchFrCircuitRxExcessA

The Rx excess in bytes per interval.

Integer32

Constraints:
range: 0-200

.1.3.6.1.4.1.164.8.8.6.1.11

pktSwchFrCircuitFunnelIdA

The funnel ID.

Integer32

Constraints:
range: 0-3

.1.3.6.1.4.1.164.8.8.6.1.12

pktSwchFrCircuitFunnelStat

The funnel status.

SNMPv2-TCDisplayString

Constraints:
range: 0-200

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.8.6.1.13

pktSwchFrCircuitTxCongDiscards

The number of frames discarded because of Tx congestion.

SNMPv2-SMICounter32

Enumerated Values:

1	r2400bps
2	r4800bps
3	r9600bps
4	r14400bps
5	r19200bps
6	r38400bps
7	r48Kbps
8	r56Kbps
9	r64Kbps
10	r128Kbps
11	r256Kbps
12	r384Kbps
13	r504Kbps
14	r768Kbps
15	r1008Kbps
16	r1466Kbps
17	r2016Kbps
255	external

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.8.6.1.14

pktSwchFrCircuitDeTxFrames

The number of DE Tx frames.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.8.6.1.15

pktSwchFrCircuitDeRxFrames

The number of DE Rx frames.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.8.6.1.16

pktSwchFrCircuitFecnTxFrames

The number of FECN Tx frames.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.8.6.1.17

pktSwchFrCircuitBecnTxFrames

The number of BECN Tx frames.

SNMPv2-SMICounter32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.8.6.1.18

pktSwchFrCircuitCommRateViolTxFrames

The number of Tx committed rate violations in number of frames.

SNMPv2-SMICounter32

Constraints:
range: 0-7

.1.3.6.1.4.1.164.8.8.6.1.19

pktSwchFrCircuitCommRateViolRxFrames

The number of Rx committed rate violations in number of frames.

SNMPv2-SMICounter32

Constraints:
range: 1-99

.1.3.6.1.4.1.164.8.8.6.1.20

pktSwchFrCircuitExcessRateViolTxFrames

The number of Tx excess rate violations in number of frames.

SNMPv2-SMICounter32

Constraints:
range: 1-99

.1.3.6.1.4.1.164.8.8.6.1.21

pktSwchFrCircuitExcessRateViolRxFrames

The number of Rx excess rate violations in number of frames.

SNMPv2-SMICounter32

Constraints:
range: 0-200

.1.3.6.1.4.1.164.8.8.6.1.22

pktSwchFrCircuitState

Indicates whether the particular virtual cir-
cuit is new or not.

Enumeration

Constraints:
range: 0-3

.1.3.6.1.4.1.164.8.8.6.1.23

pktSwchFrCircuitExtendedDlciA

The no. of the DLCI represented in 23 bits.

Integer32

Constraints:
range: 0-200

.1.3.6.1.4.1.164.8.8.6.1.24

pktSwchFrCircuitTxPriorityA

DLCI TX Priority level. The levels are defined in the
pktSwchTxPriorityTable

Integer32

Enumerated Values:

1	r2400bps
2	r4800bps
3	r9600bps
4	r14400bps
5	r19200bps
6	r38400bps
7	r48Kbps
8	r56Kbps
9	r64Kbps
10	r128Kbps
11	r256Kbps
12	r384Kbps
13	r504Kbps
14	r768Kbps
15	r1008Kbps
16	r1466Kbps
17	r2016Kbps
255	external

.1.3.6.1.4.1.164.8.8.6.1.25

pktSwchFrCircuitIsdnRoutIdA

ISDN destination. ID in the ISDN routing table containing
the outgoing ISDN address for this DLCI.

Default value: 0 for no ISDN routing ID.

Integer32

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.8.8.6.1.26

pktSwchFrFunnelSTable

table

.1.3.6.1.4.1.164.8.8.7 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchFrFunnelSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchFrFunnelSTable'

The Frame Relay Funnel Table defines the funnels that DLCIs may use.

pktSwchFrFunnelSEntry row .1.3.6.1.4.1.164.8.8.7.1

Defines the contents of each line in the RAD PS Frame Relay Funnel Table.

Indexes

IF-MIBifIndex pktSwchMpeAddressIdS

Column Syntax OID

pktSwchFrFunnelIndexS

This is the index of the funnel table.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.8.7.1.1

pktSwchFrFunnelSizeS

The number of frames the funnel can store internally, where each
frame is 512 bytes.

Integer32r/w

Enumerated Values:

1	x25Svc
2	x25Pvc
3	fr
4	innerCom
255	notActive

.1.3.6.1.4.1.164.8.8.7.1.2

pktSwchFrFunnelHighWaterFramesS

The maximum number of frames the funnel can hold before it
expands and transmits all the data.

Integer32r/w

Constraints:
range: 0-200

.1.3.6.1.4.1.164.8.8.7.1.3

pktSwchFrFunnelHighWaterBytesS

The maximum number of bytes the funnel can hold before it expands
and transmits all the data.

Integer32r/w

Constraints:
range: 0-991

.1.3.6.1.4.1.164.8.8.7.1.4

pktSwchFrFunnelGaugeTxRateS

The outgoing data rate in bytes per window of the funnel.

Integer32r/w

Enumerated Values:

1	x25Svc
2	x25Pvc
3	fr
4	innerCom
255	notActive

.1.3.6.1.4.1.164.8.8.7.1.5

pktSwchFrFunnelTransWindowS

The transmission rate is measured during a sliding time window.
This parameter defines the window in 1/10 seconds.

Integer32r/w

Constraints:
range: 0-200

.1.3.6.1.4.1.164.8.8.7.1.6

pktSwchFrFunnelStatusS

The status of this funnel table entry. The choices are those defined in the SNMPv2 Textual
Conventions for RowStatus. This will allow easy replacement of the INTEGER syntax with
the RowStatus textual convention SYNTAX.

Enumerationr/w

Constraints:
range: 0-991

.1.3.6.1.4.1.164.8.8.7.1.7

pktSwchFrFunnelATable

table

.1.3.6.1.4.1.164.8.8.8 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchFrFunnelATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchFrFunnelATable'

The Frame Relay Funnel Table defines the funnels that DLCIs may use.

pktSwchFrFunnelAEntry row .1.3.6.1.4.1.164.8.8.8.1

Defines the contents of each line in the RAD PS Frame Relay Funnel Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchFrFunnelIndexA

This is the index of the funnel table.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.8.8.1.1

pktSwchFrFunnelSizeA

The number of frames the funnel can store internally, where each frame is 512 bytes.

Integer32

.1.3.6.1.4.1.164.8.8.8.1.2

pktSwchFrFunnelHighWaterFramesA

The maximum number of frames the funnel can hold before it expands and transmits all the data.

Integer32

Enumerated Values:

1	x25Svc
2	x25Pvc
3	fr
4	innerCom
255	notActive

.1.3.6.1.4.1.164.8.8.8.1.3

pktSwchFrFunnelHighWaterBytesA

The maximum number of bytes the funnel can hold before it expands and transmits all the data.

Integer32

Constraints:
range: 0-200

.1.3.6.1.4.1.164.8.8.8.1.4

pktSwchFrFunnelGaugeTxRateA

The outgoing data rate in bytes per window of the funnel.

Integer32

Constraints:
range: 0-991

.1.3.6.1.4.1.164.8.8.8.1.5

pktSwchFrFunnelTransWindowA

The transmission rate is measured during a sliding time window. This parameter defines the
window in 1/10 seconds.

Integer32

Enumerated Values:

1	x25Svc
2	x25Pvc
3	fr
4	innerCom
255	notActive

.1.3.6.1.4.1.164.8.8.8.1.6

pktSwchFrDlciMapTable

table

.1.3.6.1.4.1.164.8.8.9 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchFrDlciMapTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchFrDlciMapTable'

The Frame Relay Dlci mapping Table maps the Dlci numbers.
For each long Dlci a short one is mapped.
A long Dlci is a Dlci which contains a Dlci header of 3 or
4 bytes instead of the regular 2 bytes.
The long Dlci number has values from 1024 to 8,388,607.

pktSwchFrDlciMapEntry row .1.3.6.1.4.1.164.8.8.9.1

Defines the contents of each Dlci Map Table entry.

Indexes

No indexes recorded

Column Syntax OID

pktSwchFrDlciMapPort

Frame Relay port no. : 1-8 for FPS-8, 1-4 for FPS-4,
1-3 for APS, 1-6 for SPS-6, 1-12 for SPS-12.

SNMPv2-SMIInteger32

Enumerated Values:

1	disconnect
2	connect
3	pvc

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.8.9.1.1

pktSwchFrDlciMapLongDlci

The Long Dlci number.
For Dlci's of 4 octets, the long Dlci number has values
from 1024 to 8,388,607.
For Dlci's of 2 octets, the long Dlci number has values
of 16-991.

Integer32

Enumerated Values:

1	inactive
2	active

.1.3.6.1.4.1.164.8.8.9.1.2

pktSwchFrDlciMapShortDlci

The Short Dlci number. Legal values: 0 - 1023.

Integer32

.1.3.6.1.4.1.164.8.8.9.1.3

pktSwchFrDlciMapStatus

The status of the map row in the Table.
The only value which can be set is: createRequest.
This value is set when a new long dlci is created.

Enumerationr/w

.1.3.6.1.4.1.164.8.8.9.1.4

pktSwchMpeSTable

table

.1.3.6.1.4.1.164.8.9.1 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchMpeSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchMpeSTable'

The MPE Table defines Scratch configuration parameters for the MPE protocol.

pktSwchMpeSEntry row .1.3.6.1.4.1.164.8.9.1.1

Defines the contents of each line in the MPE Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchMpeLinkNumberS

The link number with which this entry is associated. This value
corresponds to pktSwchPhyInterfaceNumber. There is an entry for
each link for which the pktSwchPhyInterfaceProtocol is MPE.

SNMPv2-SMIInteger32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.9.1.1.1

pktSwchMpeInactivityS

The amount of time in minutes of inactivity that will cause the
session to disconnect.

Integer32r/w

Enumerated Values:

1	one
2	two
3	oneAndHalf

.1.3.6.1.4.1.164.8.9.1.1.2

pktSwchMpeX25FacilitiesS

Integer32r/w

Constraints:
range: 5-8

.1.3.6.1.4.1.164.8.9.1.1.3

pktSwchMpeLocSubAddr1S

The first local subaddress.

Integer32r/w

Enumerated Values:

1	space
2	mark
3	even
4	odd
255	none

.1.3.6.1.4.1.164.8.9.1.1.4

pktSwchMpeLocSubAddr2S

The second local subaddress.

Integer32r/w

.1.3.6.1.4.1.164.8.9.1.1.5

pktSwchMpeFlwCtrlDurS

The duration in 50 milliseconds of a hardware flow control signal. Default is 0

Integer32r/w

.1.3.6.1.4.1.164.8.9.1.1.6

pktSwchMpeFlwCtrlOptS

This specifies the type of flow control of the MPE link. The value
is a sum of values (powers of two), where each value in the sum
represents an option. The values that may be included in the sum
and their meanings ar…

Integer32r/w

Enumerated Values:

1	slip
2	x25SVC
3	x25PVC
4	frameRelay
5	hdlc
255	none

.1.3.6.1.4.1.164.8.9.1.1.7

pktSwchMpeFlwCtrlBufS

The number of buffers that will be allocated for the MPE link.

Integer32r/w

.1.3.6.1.4.1.164.8.9.1.1.8

pktSwchMpeInternalClkS

The baud rate of the internal clock.

Enumerationr/w

.1.3.6.1.4.1.164.8.9.1.1.9

pktSwchMpeATable

table

.1.3.6.1.4.1.164.8.9.2 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchMpeATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchMpeATable'

The MPE Table defines Active configuration parameters for the MPE protocol.

pktSwchMpeAEntry row .1.3.6.1.4.1.164.8.9.2.1

Defines the contents of each line in the MPE Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchMpeLinkNumberA

The link number with which this entry is associated. This value
corresponds to pktSwchPhyInterfaceNumber. There is an entry for
each link for which the pktSwchPhyInterfaceProtocol is MPE.

SNMPv2-SMIInteger32

Enumerated Values:

1	s110bps
2	s300bps
3	s1200bps
4	s600bps
5	s75bps
6	s150bps
12	s2400bps
13	s4800bps
14	s9600bps
15	s19200bps
19	s38400bps
20	s57600bps
21	s115200bps

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.9.2.1.1

pktSwchMpeInactivityA

The amount of time in minutes of inactivity that will cause the
session to disconnect.

Integer32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.9.2.1.2

pktSwchMpeX25FacilitiesA

Integer32

Enumerated Values:

1	one
2	two
3	oneAndHalf

.1.3.6.1.4.1.164.8.9.2.1.3

pktSwchMpeLocSubAddr1A

The first local subaddress.

Integer32

Constraints:
range: 5-8

.1.3.6.1.4.1.164.8.9.2.1.4

pktSwchMpeLocSubAddr2A

The second local subaddress.

Integer32

Enumerated Values:

1	space
2	mark
3	even
4	odd
255	none

.1.3.6.1.4.1.164.8.9.2.1.5

pktSwchMpeFlwCtrlDurA

The duration in 50 milliseconds of a hardware flow control signal.

Integer32

.1.3.6.1.4.1.164.8.9.2.1.6

pktSwchMpeFlwCtrlOptA

Integer32

.1.3.6.1.4.1.164.8.9.2.1.7

pktSwchMpeFlwCtrlBufA

The number of buffers that will be allocated for the MPE link.

Integer32

Enumerated Values:

1	slip
2	x25SVC
3	x25PVC
4	frameRelay
5	hdlc
255	none

.1.3.6.1.4.1.164.8.9.2.1.8

pktSwchMpeInternalClkA

The baud rate of the internal clock.

Enumeration

.1.3.6.1.4.1.164.8.9.2.1.9

pktSwchMpeCtsStatus

The CTS status.

Enumeration

.1.3.6.1.4.1.164.8.9.2.1.10

pktSwchMpeAidSTable

table

.1.3.6.1.4.1.164.8.9.3 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchMpeAidSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchMpeAidSTable'

The AID Table defines Scratch configuration parameters for the
logical connections (Address Id).

pktSwchMpeAidSEntry row .1.3.6.1.4.1.164.8.9.3.1

Defines the contents of each line in the MPE Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchMpeAddressIdS

The Address Id (AID) with which this entry is associated.

SNMPv2-SMIInteger32

Enumerated Values:

1	yes
2	no

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.9.3.1.1

pktSwchMpeAidMainTypeS

The protocol with which the AID is communicating.

Enumerationr/w

Enumerated Values:

1	half
2	full

.1.3.6.1.4.1.164.8.9.3.1.2

pktSwchMpeAidMainIdS

The link number of the protocol with which the AID is communicating.
The link number of the protocol with which the AID is communicating.

For X.25 SVC this number is Any Autocall ID (Pre-defined) ,
values…

Integer32r/w

Constraints:
range: 1-15

.1.3.6.1.4.1.164.8.9.3.1.3

pktSwchMpeAidMainSubIdS

The DLCI with which the AID is communicating.
Sub ID is used only when Type is Frame Relay or Inner Comm.
The DLCI or destination AID with which the current AID is communicating.

If type is: Frame Relay P…

Integer32r/w

Enumerated Values:

1	twoWayAlter
2	twoWaySimul

.1.3.6.1.4.1.164.8.9.3.1.4

pktSwchMpeAidBackupTypeS

The protocol with which the AID is communicating on the backup.

Enumerationr/w

Enumerated Values:

1	r2400bps
2	r4800bps
3	r9600Bps
4	r14400bps
5	r19200bps
6	r38400bps
7	r48000bps
8	r56000bps
9	r64000bps
10	r128000bps
11	r256000bps
12	r384000bps
13	r504000bps
14	r768000bps
15	r1008000bps
16	r1466000bps
17	r2016000bps
255	external

.1.3.6.1.4.1.164.8.9.3.1.5

pktSwchMpeAidBackupIdS

The link number of the protocol with which the AID is communicating
on the backup.
The link number of the protocol with which the AID is communicating.

For X.25 SVC this number is Any Autocall ID (Pre-def…

Integer32r/w

Enumerated Values:

1	nrzFlags
2	nrziFlags
3	nrzIdle
4	nrziIdle

.1.3.6.1.4.1.164.8.9.3.1.6

pktSwchMpeAidBackupSubIdS

Integer32r/w

.1.3.6.1.4.1.164.8.9.3.1.7

pktSwchMpeAidStatusS

The status of this Address Id table entry.

Enumerationr/w

.1.3.6.1.4.1.164.8.9.3.1.8

pktSwchMpeAidATable

table

.1.3.6.1.4.1.164.8.9.4 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchMpeAidATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchMpeAidATable'

The AID Table defines Active configuration parameters for the
logical connections (Address Id).

pktSwchMpeAidAEntry row .1.3.6.1.4.1.164.8.9.4.1

Defines the contents of each line in the MPE Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchMpeAddressIdA

The Address Id (AID) with which this entry is associated.

SNMPv2-SMIInteger32

Enumerated Values:

1	half
2	full

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.9.4.1.1

pktSwchMpeAidMainTypeA

The protocol with which the AID is communicating.

Enumeration

Constraints:
range: 1-15

.1.3.6.1.4.1.164.8.9.4.1.2

pktSwchMpeAidMainIdA

Integer32

Enumerated Values:

1	twoWayAlter
2	twoWaySimul

.1.3.6.1.4.1.164.8.9.4.1.3

pktSwchMpeAidMainSubIdA

Integer32

Enumerated Values:

1	r2400bps
2	r4800bps
3	r9600Bps
4	r14400bps
5	r19200bps
6	r38400bps
7	r48000bps
8	r56000bps
9	r64000bps
10	r128000bps
11	r256000bps
12	r384000bps
13	r504000bps
14	r768000bps
15	r1008000bps
16	r1466000bps
17	r2016000bps
255	external

.1.3.6.1.4.1.164.8.9.4.1.4

pktSwchMpeAidBackupTypeA

The protocol with which the AID is communicating on the backup.

Enumeration

Enumerated Values:

1	nrzFlags
2	nrziFlags
3	nrzIdle
4	nrziIdle

.1.3.6.1.4.1.164.8.9.4.1.5

pktSwchMpeAidBackupIdA

Integer32

.1.3.6.1.4.1.164.8.9.4.1.6

pktSwchMpeAidBackupSubIdA

Integer32

.1.3.6.1.4.1.164.8.9.4.1.7

pktSwchMpeAidConn

The connectivity status of the AID.

Enumeration

.1.3.6.1.4.1.164.8.9.4.1.8

pktSwchMpeAidFlwCtrl

The Flow Control status of the AID.

Enumeration

.1.3.6.1.4.1.164.8.9.4.1.9

pktSwchSlipSTable

table

.1.3.6.1.4.1.164.8.10.1 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchSlipSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchSlipSTable'

The Scratch Slip Table contains configuration information for
Slip links

pktSwchSlipSEntry row .1.3.6.1.4.1.164.8.10.1.1

Defines the contents of each line in the RAD Slip Table.

Indexes

pktSwchSnaPUNumberS

Column Syntax OID

pktSwchSlipLinkNumberS

The link number with which this entry is associated. This value
corresponds to pktSwchPhyInterfaceIfIndex. There is an entry for
each link for which the pktSwchPhyInterfaceProtocol is Slip.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.10.1.1.1

pktSwchSlipSpeedS

This parameter determines the rate of data transmission to
and from the DTE.

Enumerationr/w

Enumerated Values:

1	localXid
2	end2EndSupNoAct
3	end2EndNoSupNoAct

.1.3.6.1.4.1.164.8.10.1.1.2

pktSwchSlipFCOptionS

The flow control options
0 - No HARDWARE flow control
1..254 - Timer value (in 50ms intervals),
when timer expires, flow control stops
255 - The timer is not used

Integer32r/w

Enumerated Values:

1	enable
2	disable

.1.3.6.1.4.1.164.8.10.1.1.3

pktSwchSlipStopBitsS

This entry indicates the number of stop bits per character
supported by the PAD.
The options are either (1) one stop bit, (2) two stop bits,
or (3) 1.5 stop bits.

Enumerationr/w

Enumerated Values:

1	sdlc
2	x25Qllc
3	frameRelayLLC2

.1.3.6.1.4.1.164.8.10.1.1.4

pktSwchSlipBitPerCharS

The number of data bits per character supported by the Slip
link.

Integer32r/w

Enumerated Values:

1	primary
2	secondary

.1.3.6.1.4.1.164.8.10.1.1.5

pktSwchSlipParityS

This entry selects the type of parity to be checked and or
generated by the PAD when radSPSProfileParTreat is a value
other than 255.
The options are (1) space parity, (2) mark parity,
(3) even parity, (4) odd parity, o…

Enumerationr/w

Enumerated Values:

1	sdlc
2	x25Qllc
3	frameRelayLLC2

.1.3.6.1.4.1.164.8.10.1.1.6

pktSwchSlipIpAddressSdeprecated

The IP address connected to this Slip port. This variable is
used when an automatic connection is done by the IP Routing.

RFC1155-SMIIpAddressr/w

Enumerated Values:

1	primary
2	secondary

Type Constraints:
range: 4

.1.3.6.1.4.1.164.8.10.1.1.7

pktSwchSlipIpMaskSdeprecated

The IP mask. This variable is
used when an automatic connection by the IP Routing is done.

RFC1155-SMIIpAddressr/w

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

Type Constraints:
range: 4

.1.3.6.1.4.1.164.8.10.1.1.8

pktSwchSlipDefEncapsTypeSdeprecated

Destination protocol of this Slip port. This variable is used
when a direct connection without IP Routing is done.

Enumerationr/w

.1.3.6.1.4.1.164.8.10.1.1.9

pktSwchSlipDefDestinationSdeprecated

Default destination for this Slip port.
This variable is used when a direct connection without
IP Routing is done.
Possible values:
Default : Not Used.
X.25 PVC: Port:LCN or a pre defined PVC number
X.25 SVC: …

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.10.1.1.10

pktSwchSlipATable

table

.1.3.6.1.4.1.164.8.10.2 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchSlipATable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchSlipATable'

The Active Slip Table contains configuration information for
Slip links

pktSwchSlipAEntry row .1.3.6.1.4.1.164.8.10.2.1

Defines the contents of each line in the RAD Slip Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchSlipLinkNumberA

The link number with which this entry is associated. This value
corresponds to pktSwchPhyInterfaceIfIndex. There is an entry for
each link for which the pktSwchPhyInterfaceProtocol is Slip.

SNMPv2-SMIInteger32

Enumerated Values:

1	enable
2	disable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.10.2.1.1

pktSwchSlipSpeedA

This parameter determines the rate of data transmission to
and from the DTE.

Enumeration

Enumerated Values:

1	sdlc
2	x25Qllc
3	frameRelayLLC2

.1.3.6.1.4.1.164.8.10.2.1.2

pktSwchSlipFCOptionA

The flow control options
0 - No HARDWARE flow control
1..254 - Timer value (in 50ms intervals),
when timer expires, flow control stops
255 - The timer is not used

Integer32

Enumerated Values:

1	primary
2	secondary

.1.3.6.1.4.1.164.8.10.2.1.3

pktSwchSlipStopBitsA

This entry indicates the number of stop bits per character
supported by the PAD.
The options are either (1) one stop bit, (2) two stop bits,
or (3) 1.5 stop bits.

Enumeration

Enumerated Values:

1	sdlc
2	x25Qllc
3	frameRelayLLC2

.1.3.6.1.4.1.164.8.10.2.1.4

pktSwchSlipBitPerCharA

The number of data bits per character supported by the Slip
link.

Integer32

Enumerated Values:

1	primary
2	secondary

.1.3.6.1.4.1.164.8.10.2.1.5

pktSwchSlipParityA

This entry selects the type of parity to be checked and or
generated by the PAD when radSPSProfileParTreat is a value
other than 255.
The options are (1) space parity, (2) mark parity,
(3) even parity, (4) odd parity, o…

Enumeration

.1.3.6.1.4.1.164.8.10.2.1.6

pktSwchSlipIpAddressAdeprecated

The IP address connected to this Slip port.

RFC1155-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.164.8.10.2.1.7

pktSwchSlipIpMaskAdeprecated

The IP mask.

RFC1155-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.164.8.10.2.1.8

pktSwchSlipDefEncapsTypeAdeprecated

Destination protocol of this Slip port.

Enumeration

Enumerated Values:

1	sideA
2	sideB

.1.3.6.1.4.1.164.8.10.2.1.9

pktSwchSlipDefDestinationAdeprecated

SNMPv2-TCDisplayString

Constraints:
range: 1-1

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.10.2.1.10

pktSwchSnaSDLCLinkTableS

table

.1.3.6.1.4.1.164.8.11.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchSnaSDLCLinkTableS

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchSnaSDLCLinkTableS'

The SDLC Link Table defines the SDLC links configured on the PS.

pktSwchSnaSDLCLinkEntryS row .1.3.6.1.4.1.164.8.11.1.1

SDLC Link Entry defines the contents of each link in the SDLC Link Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchSnaSDLCLinkTypeS

This parameter identifies whether this link operates as
TPAD(Primary) or HPAD(Secondary) SDLC device.

Enumerationr/w

Constraints:
range: 1-3

.1.3.6.1.4.1.164.8.11.1.1.1

pktSwchSnaSDLCLinkPUSharedS

This parameter defines whether the link participates with more than
one PU or not.

Enumerationr/w

Constraints:
range: 137-7642

.1.3.6.1.4.1.164.8.11.1.1.2

pktSwchSnaSDLCLinkDuplexPhyS

This parameter describes whether the physical level of the
SDLC line is half or full duplex.

Enumerationr/w

.1.3.6.1.4.1.164.8.11.1.1.3

pktSwchSnaSDLCLinkflagsS

Number of flags between frames.

Integer32r/w

Constraints:
range: 1-1

.1.3.6.1.4.1.164.8.11.1.1.4

pktSwchSnaSDLCLinkDuplexS

This parameter shows wether the link level is Two Way Alternate
or Two Way Simultaneous.

Enumerationr/w

.1.3.6.1.4.1.164.8.11.1.1.5

pktSwchSnaSDLCLinkClockS

This parameter defines the link clock rate

Enumerationr/w

Enumerated Values:

1	notInitiate
2	initiate

.1.3.6.1.4.1.164.8.11.1.1.6

pktSwchSnaSDLCLinkNRZS

This parameter describes the following combinations of NRZ,
NRZI with FLAGS or IDLE between frames:
Legal values:
1 - NRZ with FLAGs between frames. RTS is Constant
2 - NRZI with FLAGs between frames. RTS is Constant…

Enumerationr/w

Enumerated Values:

1	valid
3	underCreation

.1.3.6.1.4.1.164.8.11.1.1.7

pktSwchSnaSDLCLinkTableA

table

.1.3.6.1.4.1.164.8.11.2 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchSnaSDLCLinkTableA

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchSnaSDLCLinkTableA'

The SDLC Link Table defines the SDLC links configured on the SPS.

pktSwchSnaSDLCLinkEntryA row .1.3.6.1.4.1.164.8.11.2.1

SDLC Link Entry defines the contents of each link in the SDLC Link Table.

Indexes

pktSwchSnaPUSdlcNumberA pktSwchSnaPUSdlcSideA

Column Syntax OID

pktSwchSnaSDLCLinkTypeA

This parameter identifies whether this link operates as
TPAD(Primary) or HPAD(Secondary) SDLC device.

Enumeration

.1.3.6.1.4.1.164.8.11.2.1.1

pktSwchSnaSDLCLinkPUSharedA

This parameter defines whether the link participates with more
than one PU or not.

Enumeration

Enumerated Values:

1	sideA
2	sideB

.1.3.6.1.4.1.164.8.11.2.1.2

pktSwchSnaSDLCLinkDuplexPhyA

This parameter describes whether the physical level of the
SDLC line is half or full duplex.

Enumeration

Constraints:
range: 1-1

.1.3.6.1.4.1.164.8.11.2.1.3

pktSwchSnaSDLCLinkflagsA

Number of flags between frames.

Integer32

.1.3.6.1.4.1.164.8.11.2.1.4

pktSwchSnaSDLCLinkDuplexA

This parameter shows wether the link level is Two Way Alternate
or Two Way Simultaneous.

Enumeration

Constraints:
range: 1-2

.1.3.6.1.4.1.164.8.11.2.1.5

pktSwchSnaSDLCLinkClockA

This parameter defines the link clock rate.

Enumeration

Constraints:
range: 1-3

.1.3.6.1.4.1.164.8.11.2.1.6

pktSwchSnaSDLCLinkNRZA

Enumeration

Constraints:
range: 137-7642

.1.3.6.1.4.1.164.8.11.2.1.7

pktSwchSnaSDLCLinkStatFrames

The number of frames received or transmitted via this link

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.2.1.8

pktSwchSnaSDLCLinkStatErrors

The number of error frames received.

SNMPv2-SMICounter32

Constraints:
range: 1-1

.1.3.6.1.4.1.164.8.11.2.1.9

pktSwchSnaSDLCLinkStatInvalidAddresses

The number of frames with wrong address received by this link.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.2.1.10

pktSwchSnaSDLCLinkStatShortFrames

The number of short frames received by this link.

SNMPv2-SMICounter32

Enumerated Values:

1	notInitiate
2	initiate

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.2.1.11

pktSwchSnaPUTableS

table

.1.3.6.1.4.1.164.8.11.3 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchSnaPUTableS

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchSnaPUTableS'

The SDLC PU table defines the PUs configured on the PS.

pktSwchSnaPUEntryS row .1.3.6.1.4.1.164.8.11.3.1

SDLC PU Entry defines the contents of each PU in the
SDLC PU Table.

Indexes

pktSwchSnaPUSdlcStatNumber pktSwchSnaPUSdlcStatSide

Column Syntax OID

pktSwchSnaPUNumberS

This parameter defines an identifier associated with the PU Entry
which is unique within the SPS

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.11.3.1.1

pktSwchSnaPUXIDProcessingS

Exchange Identification (XID) processing. The following values are legal:
1 - Local XID handling
2 - End-to-End XID handling, Support for NON-Activation XID
3 - End-to-End XID handling, NO Support for NON-Activation XID

Enumerationr/w

Enumerated Values:

1	sideA
2	sideB

.1.3.6.1.4.1.164.8.11.3.1.2

pktSwchSnaPUEnableS

The PU runs or not at this specific time

Enumerationr/w

.1.3.6.1.4.1.164.8.11.3.1.3

pktSwchSnaPULinkATypeS

The PU link A type.

Enumerationr/w

.1.3.6.1.4.1.164.8.11.3.1.4

pktSwchSnaPULinkARoleS

The PU role for link A. Note that the role of an SDLC PU may
not be changed. It is defined by the SDLC Link Type.

Enumerationr/w

.1.3.6.1.4.1.164.8.11.3.1.5

pktSwchSnaPULinkBTypeS

The PU partner link B type

Enumerationr/w

.1.3.6.1.4.1.164.8.11.3.1.6

pktSwchSnaPULinkBRoleS

The PU role for link B. Note that the role of an SDLC PU may
not be changed. It is defined by the SDLC Link Type.

Enumerationr/w

.1.3.6.1.4.1.164.8.11.3.1.7

pktSwchSnaPUEntryStatusS

The status of this PU table entry.
This Set request will fail if there are any conflicts between any of
of the parameter values in any of the tables comprising this PU
definition

Enumerationr/w

.1.3.6.1.4.1.164.8.11.3.1.8

pktSwchSnaPUTableA

table

.1.3.6.1.4.1.164.8.11.4 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchSnaPUTableA

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchSnaPUTableA'

The SDLC PU table defines the PUs configured on the PS.

pktSwchSnaPUEntryA row .1.3.6.1.4.1.164.8.11.4.1

SDLC PU Entry defines the contents of each PU in the
SDLC PU Table.

Indexes

No indexes recorded

Column	Syntax	OID
pktSwchSnaPUNumberA This parameter defines an identifier associated with the PU Entry which is unique within the SPS	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.8.11.4.1.1`
pktSwchSnaPUXIDProcessingA The PU XID Processing	Enumeration	`.1.3.6.1.4.1.164.8.11.4.1.2`
pktSwchSnaPUEnableA The PU runs or not at this specific time	Enumeration	`.1.3.6.1.4.1.164.8.11.4.1.3`
pktSwchSnaPULinkATypeA The PU link type	Enumeration	`.1.3.6.1.4.1.164.8.11.4.1.4`
pktSwchSnaPULinkARoleA The PU role for link A	Enumeration	`.1.3.6.1.4.1.164.8.11.4.1.5`
pktSwchSnaPULinkBTypeA The PU partner link type	Enumeration	`.1.3.6.1.4.1.164.8.11.4.1.6`
pktSwchSnaPULinkBRoleA The PU role for link B	Enumeration	`.1.3.6.1.4.1.164.8.11.4.1.7`

pktSwchSnaPUSdlcTableS

table

.1.3.6.1.4.1.164.8.11.5 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchSnaPUSdlcTableS

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchSnaPUSdlcTableS'

Defines links for PUs running on SDLC link

pktSwchSnaPUSdlcEntryS row .1.3.6.1.4.1.164.8.11.5.1

Defines parameters of a link for a PU running on an SDLC link

Indexes

No indexes recorded

Column Syntax OID

pktSwchSnaPUSdlcNumberS

This parameter defines an identifier associated with the PU Entry
SDLC side, which is unique within the SPS

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.11.5.1.1

pktSwchSnaPUSdlcSideS

Is this side A or side B of the PU definition

Enumeration

.1.3.6.1.4.1.164.8.11.5.1.2

pktSwchSnaPUSdlcAddressS

SNA SDLC PU address. Range: 0x00-0xFE

OctetStringr/w

.1.3.6.1.4.1.164.8.11.5.1.3

pktSwchSnaPUSdlcIfIndexS

ifIndex of the SDLC link

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.11.5.1.4

pktSwchSnaPUSdlcIdBlkS

Part of the IBM device ID (the full ID is defined by the IDBLK and
the IDNUM). The Idblk is required for secondary PU with Local XID
handling. Up to 3 Hexadecimal digits, format: 0X XX.

OctetStringr/w

.1.3.6.1.4.1.164.8.11.5.1.5

pktSwchSnaPUSdlcIdNumS

Second part of the IBM device ID (the full ID is defined by the IDBLK and
the IDNUM). The Idnum is required for secondary PU with Local XID
handling. Up to 5 Hexadecimal digits, format: 0X XX XX.

OctetStringr/w

.1.3.6.1.4.1.164.8.11.5.1.6

pktSwchSnaPUSdlcMaxPiuSizeS

Maximum Path Information Size

Integer32r/w

.1.3.6.1.4.1.164.8.11.5.1.7

pktSwchSnaPUSdlcTxWindowS

Window Size(in frames) used when sending from the SPS. Range: 1-7.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.11.5.1.8

pktSwchSnaPUSdlcGrpAddressS

SNA Group address used by the SPS when sending polls (TPAD ONLY).
Range: 0x00-0xFE

OctetStringr/w

.1.3.6.1.4.1.164.8.11.5.1.9

pktSwchSnaPUSdlcPollTimerS

Time in between polls in 50 millisecond increments (TPAD ONLY).
Range: 1-65535.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	unbound
2	bindPending
3	unbindPend
4	idle
5	unattached
6	attachPend
7	detachPend
8	udqosPending
9	outconPend
10	inconPending
11	connResPend
12	dataxfer
13	userResetPend
14	provRstPend
15	rstResPend
16	discon8Pend
17	discon9Pend
18	discon11Pend
19	discon12Pend
20	discon13Pend
21	subsBindPnd
22	noChange

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.11.5.1.10

pktSwchSnaPUSdlcXIDInitiationS

This parameter is not applicable for PU with Local XID handling.
Legal values:
1 - Do not initiate an XID message.
2 - Initiate an XID message to SDLC.

Enumerationr/w

Enumerated Values:

1	linkClosed
2	disconnected
3	linkOpening
4	disconnecting
5	frmrSent
6	linkOpened
7	localBusy
8	rejection
9	checkpointing
10	cpLocalBusy
11	cpRejection
12	resetting
13	remoteBusy
14	lBusyRBusy
15	rejLBusy
16	rejRBusy
17	cpRejLBusy
18	cpClearing
19	cpRejClr
20	rejLbusyRbusy
21	frmrReceived
22	programError
23	noChange

.1.3.6.1.4.1.164.8.11.5.1.11

pktSwchSnaPUSdlcEntryStatusS

The status of this PU Sdlc table entry.
In order to save this entry, set status to valid.
An underCreation value is set by the Agent when this entry is updated.

Enumerationr/w

Enumerated Values:

1	sync
2	notSync

.1.3.6.1.4.1.164.8.11.5.1.12

pktSwchSnaPUSdlcTableA

table

.1.3.6.1.4.1.164.8.11.6 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchSnaPUSdlcTableA

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchSnaPUSdlcTableA'

Defines links for PUs running on an SDLC link

pktSwchSnaPUSdlcEntryA row .1.3.6.1.4.1.164.8.11.6.1

Defines parameters of link for PU running on an SDLC link

Indexes

No indexes recorded

Column Syntax OID

pktSwchSnaPUSdlcNumberA

This parameter defines an identifier associated with the PU Entry
SDLC side, which is unique within the SPS

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.11.6.1.1

pktSwchSnaPUSdlcSideA

Is this side A or side B of the PU definition

Enumeration

.1.3.6.1.4.1.164.8.11.6.1.2

pktSwchSnaPUSdlcAddressA

SNA SDLC PU address. Range: 0x00-0xFE.

OctetString

Enumerated Values:

1	sideA
2	sideB

.1.3.6.1.4.1.164.8.11.6.1.3

pktSwchSnaPUSdlcIfIndexA

ifIndex of the SDLC link

SNMPv2-SMIInteger32

Constraints:
range: 1-2

.1.3.6.1.4.1.164.8.11.6.1.4

pktSwchSnaPUSdlcIdBlkA

Part of the IBM device ID (the full ID is defined by the IDBLK and
the IDNUM). The Idblk is required for secondary PU with Local XID
handling. Up to 3 Hexadecimal digits, format: 0X XX.

OctetString

Constraints:
range: 1-3

.1.3.6.1.4.1.164.8.11.6.1.5

pktSwchSnaPUSdlcIdNumA

Second part of the IBM device ID (the full ID is defined by the IDBLK and
the IDNUM). The Idnum is required for secondary PU with Local XID
handling. Up to 5 Hexadecimal digits, format: 0X XX XX.

OctetString

Enumerated Values:

1	notInitiate
2	initiate

.1.3.6.1.4.1.164.8.11.6.1.6

pktSwchSnaPUSdlcMaxPiuSizeA

Maximum Path Information Size

Integer32

Constraints:
range: 137-7642

.1.3.6.1.4.1.164.8.11.6.1.7

pktSwchSnaPUSdlcTxWindowA

Window Size(in frames) used when sending from the SPS.
Range: 1-7.

SNMPv2-SMIInteger32

Constraints:
range: 1-1

.1.3.6.1.4.1.164.8.11.6.1.8

pktSwchSnaPUSdlcGrpAddressA

SNA Group address used by the SPS when sending polls (TPAD ONLY).
Range: 0x00-0xFE.

OctetString

Constraints:
range: 1-8

.1.3.6.1.4.1.164.8.11.6.1.9

pktSwchSnaPUSdlcPollTimerA

Time in between polls in 50 millisecond increments (TPAD ONLY).
Range: 1-65535.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.11.6.1.10

pktSwchSnaPUSdlcXIDInitiationA

This parameter is not applicable for PU with Local XID handling.
Legal values:
1 - Do not initiate an XID message.
2 - Initiate an XID message to SDLC.

Enumeration

Enumerated Values:

1	yes
2	no

.1.3.6.1.4.1.164.8.11.6.1.11

pktSwchSnaPUSdlcStatTable

table

.1.3.6.1.4.1.164.8.11.7 · 1 row entry · 32 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchSnaPUSdlcStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchSnaPUSdlcStatTable'

Shows Link Statistics for PUs running on an SDLC link

pktSwchSnaPUSdlcStatEntry row .1.3.6.1.4.1.164.8.11.7.1

Shows Link Statistics for PUs running on an SDLC link

Indexes

No indexes recorded

Column Syntax OID

pktSwchSnaPUSdlcStatNumber

This parameter defines an identifier associated with the PU Entry
SDLC side statistics, which is unique within the SPS

SNMPv2-SMIInteger32

Enumerated Values:

1	valid
3	underCreation

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.11.7.1.1

pktSwchSnaPUSdlcStatSide

Is this side A or side B of the PU definition

Enumeration

.1.3.6.1.4.1.164.8.11.7.1.2

pktSwchSnaPUSdlcStatOctetsIn

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.7.1.3

pktSwchSnaPUSdlcStatOctetsOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.7.1.4

pktSwchSnaPUSdlcStatIFramesIn

SNMPv2-SMICounter32

Enumerated Values:

1	sideA
2	sideB

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.7.1.5

pktSwchSnaPUSdlcStatIFramesOut

SNMPv2-SMICounter32

Constraints:
range: 1-2

.1.3.6.1.4.1.164.8.11.7.1.6

pktSwchSnaPUSdlcStatRRFramesIn

SNMPv2-SMICounter32

Constraints:
range: 1-3

.1.3.6.1.4.1.164.8.11.7.1.7

pktSwchSnaPUSdlcStatRRFramesOut

SNMPv2-SMICounter32

Enumerated Values:

1	notInitiate
2	initiate

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.7.1.8

pktSwchSnaPUSdlcStatRNRFramesIn

SNMPv2-SMICounter32

Constraints:
range: 137-7642

.1.3.6.1.4.1.164.8.11.7.1.9

pktSwchSnaPUSdlcStatRNRFramesOut

SNMPv2-SMICounter32

Constraints:
range: 1-1

.1.3.6.1.4.1.164.8.11.7.1.10

pktSwchSnaPUSdlcStatXIDsIn

SNMPv2-SMICounter32

Constraints:
range: 1-8

.1.3.6.1.4.1.164.8.11.7.1.11

pktSwchSnaPUSdlcStatXIDsOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.7.1.12

pktSwchSnaPUSdlcStatTESTsIn

SNMPv2-SMICounter32

Enumerated Values:

1	yes
2	no

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.7.1.13

pktSwchSnaPUSdlcStatTESTsOut

SNMPv2-SMICounter32

Constraints:
range: 1-15

.1.3.6.1.4.1.164.8.11.7.1.14

pktSwchSnaPUSdlcStatREJsIn

SNMPv2-SMICounter32

Constraints:
range: 1-60

.1.3.6.1.4.1.164.8.11.7.1.15

pktSwchSnaPUSdlcStatREJsOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.7.1.16

pktSwchSnaPUSdlcStatFRMRsIn

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.7.1.17

pktSwchSnaPUSdlcStatFRMRsOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.7.1.18

pktSwchSnaPUSdlcStatDISCsIn

SNMPv2-SMICounter32

Enumerated Values:

1	sideA
2	sideB

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.7.1.19

pktSwchSnaPUSdlcStatDISCsOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.7.1.20

pktSwchSnaPUSdlcStatUAsIn

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.7.1.21

pktSwchSnaPUSdlcStatUAsOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.7.1.22

pktSwchSnaPUSdlcStatDMsIn

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.7.1.23

pktSwchSnaPUSdlcStatDMsOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.7.1.24

pktSwchSnaPUSdlcStatSNRMsIn

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.7.1.25

pktSwchSnaPUSdlcStatSNRMsOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.7.1.26

pktSwchSnaPUSdlcStatRetransmitsIn

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.7.1.27

pktSwchSnaPUSdlcStatRetransmitsOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.7.1.28

pktSwchSnaPUSdlcUpperState

The internal DLPI state of the connection.

Enumeration

.1.3.6.1.4.1.164.8.11.7.1.29

pktSwchSnaPUSdlcLowerState

The internal SDLC state of the connection.

Enumeration

.1.3.6.1.4.1.164.8.11.7.1.30

pktSwchSnaPUSdlcStatNRMStatus

This variable indicates if the link is in Normal Response Mode or not.

Enumeration

.1.3.6.1.4.1.164.8.11.7.1.31

pktSwchSnaPUSdlcStatFlowCtlStatus

This variable indicates the flow control status of the PU interface.

Enumeration

.1.3.6.1.4.1.164.8.11.7.1.32

pktSwchSnaPUSX25QllcTableS

table

.1.3.6.1.4.1.164.8.11.8 · 1 row entry · 13 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchSnaPUSX25QllcTableS

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchSnaPUSX25QllcTableS'

Defines links for PUs running on a QLLC link

pktSwchSnaPUX25QllcEntryS row .1.3.6.1.4.1.164.8.11.8.1

Defines parameters for PU side running on SDLC link

Indexes

No indexes recorded

Column Syntax OID

pktSwchSnaPUX25QllcNumberS

This parameter defines an identifier associated with the PU Entry
X25\QLLC side, which is unique within the SPS

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.11.8.1.1

pktSwchSnaPUX25QllcSideS

Is there side A or B of the PU connection

Enumeration

.1.3.6.1.4.1.164.8.11.8.1.2

pktSwchSnaPUX25QllcIdBlkS

Part of the IBM device ID (the full ID is defined by the IDBLK and
the IDNUM). The Idblk is required for secondary PU with Local XID
handling. Up to 3 Hexadecimal digits, format: 0X XX.

OctetStringr/w

Enumerated Values:

1	unbound
2	bindPending
3	unbindPend
4	idle
5	unattached
6	attachPend
7	detachPend
8	udqosPending
9	outconPend
10	inconPending
11	connResPend
12	dataxfer
13	userResetPend
14	provRstPend
15	rstResPend
16	discon8Pend
17	discon9Pend
18	discon11Pend
19	discon12Pend
20	discon13Pend
21	subsBindPnd
22	noChange

.1.3.6.1.4.1.164.8.11.8.1.3

pktSwchSnaPUX25QllcIdNumS

Second part of the IBM device ID (the full ID is defined by the IDBLK and
the IDNUM). The Idnum is required for secondary PU with Local XID
handling. Up to 5 Hexadecimal digits, format: 0X XX XX.

OctetStringr/w

Enumerated Values:

1	linkClosed
2	disconnected
3	linkOpening
4	disconnecting
5	frmrSent
6	linkOpened
7	localBusy
8	rejection
9	checkpointing
10	cpLocalBusy
11	cpRejection
12	resetting
13	remoteBusy
14	lBusyRBusy
15	rejLBusy
16	rejRBusy
17	cpRejLBusy
18	cpClearing
19	cpRejClr
20	rejLbusyRbusy
21	frmrReceived
22	programError
23	noChange

.1.3.6.1.4.1.164.8.11.8.1.4

pktSwchSnaPUX25QllcXIDInitS

This parameter is not applicable for PU with Local XID handling.
Legal values:
1 - Do not initiate an XID message.
2 - Initiate an XID message to QLLC.

Enumerationr/w

Enumerated Values:

1	sync
2	notSync

.1.3.6.1.4.1.164.8.11.8.1.5

pktSwchSnaPUX25QllcMaxPiuSizeS

Maximum Path Information Size

Integer32r/w

Enumerated Values:

1	noRNR
2	txFlow
3	rxFlow
4	rxAndTx

.1.3.6.1.4.1.164.8.11.8.1.6

pktSwchSnaPUX25QllcStationAddressS

QLLC PU Link Station Address. Range: 0x01-0xFE.
This parameter is applicable only for PU with End-to-End XID handling,
Support for NON-Activation XID.

OctetStringr/w

.1.3.6.1.4.1.164.8.11.8.1.7

pktSwchSnaPUX25QllcInPasswordS

A field matched with the call user data in call request packets for
purposes of security and correlation.

OctetStringr/w

.1.3.6.1.4.1.164.8.11.8.1.8

pktSwchSnaPUX25QllcSubAddressS

The X.25 Sub-address associated with the PU Entry for routing
incoming call indications. Range: 0-99.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.11.8.1.9

pktSwchSnaPUX25QllcAutoCallS

This parameter indicates whether the SPS automatically initiates
an X.25 call request or not.

Enumerationr/w

Enumerated Values:

1	sideA
2	sideB

.1.3.6.1.4.1.164.8.11.8.1.10

pktSwchSnaPUX25QllcCalledAddressS

The destination x.25 DTE address to which the SPS calls. Used with
AutoCall only.

OctetStringr/w

Enumerated Values:

1	ban
2	bnn
3	tren

.1.3.6.1.4.1.164.8.11.8.1.11

pktSwchSnaPUX25QllcCallUserDataFacilitiesS

The X.25 facilities and Call User Data which the SPS uses on
outgoing calls. AutoCall only.
Up to 60 Hexa-Decimal digits.
Each pair of digits represents a BYTE.
BYTE-0 BYTE-1 BYTE-2 ... BYTE-29 (30 Bytes maximum)
…

OctetStringr/w

Constraints:
range: 6-6

.1.3.6.1.4.1.164.8.11.8.1.12

pktSwchSnaPUX25QllcEntryStatusS

The status of this PU Qllc table entry.
In order to save this entry, set status to valid.
An underCreation value is set by the Agent when this entry is updated.

Enumerationr/w

Constraints:
range: 1-1

.1.3.6.1.4.1.164.8.11.8.1.13

pktSwchSnaPUX25QllcTableA

table

.1.3.6.1.4.1.164.8.11.9 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchSnaPUX25QllcTableA

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchSnaPUX25QllcTableA'

Defines links for PUs running on a QLLC link

pktSwchSnaPUX25QllcEntryA row .1.3.6.1.4.1.164.8.11.9.1

Defines parameters for PU side running on an SDLC link

Indexes

No indexes recorded

Column Syntax OID

pktSwchSnaPUX25QllcNumberA

This parameter defines an identifier associated with the PU Entry
X25\QLLC side, which is unique within the SPS

SNMPv2-SMIInteger32

Constraints:
range: 1-3

.1.3.6.1.4.1.164.8.11.9.1.1

pktSwchSnaPUX25QllcSideA

Is there side A or B of the PU connection

Enumeration

Constraints:
range: 137-7642

.1.3.6.1.4.1.164.8.11.9.1.2

pktSwchSnaPUX25QllcIdBlkA

Part of the IBM device ID (the full ID is defined by the IDBLK and
the IDNUM). The Idblk is required for secondary PU with Local XID
handling. Up to 3 Hexadecimal digits, format: 0X XX.

OctetString

.1.3.6.1.4.1.164.8.11.9.1.3

pktSwchSnaPUX25QllcIdNumA

Second part of the IBM device ID (the full ID is defined by the IDBLK and
the IDNUM). The Idnum is required for secondary PU with Local XID
handling. Up to 5 Hexadecimal digits, format: 0X XX XX.

OctetString

.1.3.6.1.4.1.164.8.11.9.1.4

pktSwchSnaPUX25QllcXIDInitA

This parameter is not applicable for PU with Local XID handling.
Legal values:
1 - Do not initiate an XID message.
2 - Initiate an XID message to QLLC.

Enumeration

.1.3.6.1.4.1.164.8.11.9.1.5

pktSwchSnaPUX25QllcMaxPiuSizeA

Maximum Path Information Size

Integer32

Enumerated Values:

1	notInitiate
2	initiate

.1.3.6.1.4.1.164.8.11.9.1.6

pktSwchSnaPUX25QllcStationAddressA

QLLC PU Link Station Address. Range: 0x01-0xFE.
This parameter is applicable only for PU with End-to-End XID handling,
Support for NON-Activation XID.

OctetString

Constraints:
range: 1-99999

.1.3.6.1.4.1.164.8.11.9.1.7

pktSwchSnaPUX25QllcInPasswordA

A field matched with the call user data in call request packets for
purposes of security and correlation.

OctetString

Constraints:
range: 1-99999

.1.3.6.1.4.1.164.8.11.9.1.8

pktSwchSnaPUX25QllcSubAddressA

The X.25 Sub-address associated with the PU Entry for routing
incoming call indications. Range: 0-99.

SNMPv2-SMIInteger32

Constraints:
range: 1-99999

.1.3.6.1.4.1.164.8.11.9.1.9

pktSwchSnaPUX25QllcAutoCallA

This parameter indicates whether the SPS automatically initiates
an X.25 call request or not.

Enumeration

Enumerated Values:

1	valid
3	underCreation

.1.3.6.1.4.1.164.8.11.9.1.10

pktSwchSnaPUX25QllcCalledAddressA

The destination x.25 DTE address to which the SPS calls. Used
with AutoCall only.

OctetString

.1.3.6.1.4.1.164.8.11.9.1.11

pktSwchSnaPUX25QllcCallUserDataFacilitiesA

OctetString

.1.3.6.1.4.1.164.8.11.9.1.12

pktSwchSnaPUX25QllcStatTable

table

.1.3.6.1.4.1.164.8.11.10 · 1 row entry · 23 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchSnaPUX25QllcStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchSnaPUX25QllcStatTable'

Shows link statistics for PUs running on a QLLC link

pktSwchSnaPUX25QllcStatEntry row .1.3.6.1.4.1.164.8.11.10.1

Shows link statistics for PUs running on a QLLC link

Indexes

No indexes recorded

Column Syntax OID

pktSwchSnaPUX25QllcStatNumber

This parameter defines an identifier associated with the PU Entry
X25\QLLC side, which is unique within the SPS

SNMPv2-SMIInteger32

Enumerated Values:

1	ban
2	bnn
3	tren

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.11.10.1.1

pktSwchSnaPUX25QllcStatSide

Is there side A or B of the PU connection

Enumeration

Constraints:
range: 6-6

.1.3.6.1.4.1.164.8.11.10.1.2

pktSwchSnaPUX25QllcStatlink

The Link on which the Qllc conversation is conducted. If there is
no conversation the variable will be 0.

SNMPv2-SMIInteger32

Constraints:
range: 1-1

.1.3.6.1.4.1.164.8.11.10.1.3

pktSwchSnaPUX25QllcStatDataPacketsIn

SNMPv2-SMICounter32

Constraints:
range: 1-1

.1.3.6.1.4.1.164.8.11.10.1.4

pktSwchSnaPUX25QllcStatDataPacketsOut

SNMPv2-SMICounter32

Constraints:
range: 1-2

.1.3.6.1.4.1.164.8.11.10.1.5

pktSwchSnaPUX25QllcStatQSMPacketsIn

SNMPv2-SMICounter32

Constraints:
range: 1-3

.1.3.6.1.4.1.164.8.11.10.1.6

pktSwchSnaPUX25QllcStatQSMPacketsOut

SNMPv2-SMICounter32

Constraints:
range: 137-7642

.1.3.6.1.4.1.164.8.11.10.1.7

pktSwchSnaPUX25QllcStatQDMPacketsIn

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.10.1.8

pktSwchSnaPUX25QllcStatQDMPacketsOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.10.1.9

pktSwchSnaPUX25QllcStatXIDPacketsIn

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.10.1.10

pktSwchSnaPUX25QllcStatXIDPacketsOut

SNMPv2-SMICounter32

Enumerated Values:

1	notInitiate
2	initiate

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.10.1.11

pktSwchSnaPUX25QllcStatQDISCPacketsIn

SNMPv2-SMICounter32

Constraints:
range: 1-99999

.1.3.6.1.4.1.164.8.11.10.1.12

pktSwchSnaPUX25QllcStatQDISCPacketsOut

SNMPv2-SMICounter32

Constraints:
range: 1-99999

.1.3.6.1.4.1.164.8.11.10.1.13

pktSwchSnaPUX25QllcStatCallPacketsIn

SNMPv2-SMICounter32

Constraints:
range: 1-99999

.1.3.6.1.4.1.164.8.11.10.1.14

pktSwchSnaPUX25QllcStatCallPacketsOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.10.1.15

pktSwchSnaPUX25QllcStatClearPacketsIn

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.10.1.16

pktSwchSnaPUX25QllcStatClearPacketsOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.10.1.17

pktSwchSnaPUX25QllcStatCallAcceptsIn

SNMPv2-SMICounter32

Enumerated Values:

1	sideA
2	sideB

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.10.1.18

pktSwchSnaPUX25QllcStatCallAcceptsOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.10.1.19

pktSwchSnaPUX25QllcStatUpperState

The internal DLPI state of the connection.

Enumeration

.1.3.6.1.4.1.164.8.11.10.1.20

pktSwchSnaPUX25QllcStatLowerState

The internal QLLC state of the connection.

Enumeration

.1.3.6.1.4.1.164.8.11.10.1.21

pktSwchSnaPUX25QllcStatNRMStatus

This variable indicates if the link is in Normal Response Mode or not.

Enumeration

.1.3.6.1.4.1.164.8.11.10.1.22

pktSwchSnaPUX25QllcStatFlowCtlStatus

This variable indicates the flow control status of the PU interface.

Enumeration

.1.3.6.1.4.1.164.8.11.10.1.23

pktSwchSnaPULlc2FrTableS

table

.1.3.6.1.4.1.164.8.11.11 · 1 row entry · 17 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchSnaPULlc2FrTableS

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchSnaPULlc2FrTableS'

Defines LLC2/Frame Relay/RFC1490 Protocol Interface of SPS SNA PU entity.

pktSwchSnaPULlc2FrEntryS row .1.3.6.1.4.1.164.8.11.11.1

Defines parameters for PU LLC2 Protocol Interface over Frame Relay Protocol using RFC 1490.

Indexes

No indexes recorded

Column	Syntax	OID
pktSwchSnaPULlc2FrNumberS Unique Identifier for this PU. The value in this field is used as a common Key in both this table and the Main PU table.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.8.11.11.1.1`
pktSwchSnaPULlc2FrSideS Indicates for each side (SIDE-A and SIDE-B) if the Protocol Interface for that side has been defined or not.	Enumeration	`.1.3.6.1.4.1.164.8.11.11.1.2`
pktSwchSnaPULlc2FrEncapsTypeS Indicates if the LLC2/RFC1490 Protocol Interface uses the BNN, BAN or TREN method of Frame Encapsulation.	Enumerationr/w	`.1.3.6.1.4.1.164.8.11.11.1.3`
pktSwchSnaPULlc2FrDestMACS The LLC2 Destination MAC Address.	OctetStringr/w	`.1.3.6.1.4.1.164.8.11.11.1.4`
pktSwchSnaPULlc2FrSrcSAPS The LLC2 Source SAP Address. 2 Hex digits	OctetStringr/w	`.1.3.6.1.4.1.164.8.11.11.1.5`
pktSwchSnaPULlc2FrDestSAPS The LLC2 Destination SAP.	OctetStringr/w	`.1.3.6.1.4.1.164.8.11.11.1.6`
pktSwchSnaPULlc2FrXIDIdBlkS Part of the IBM device ID (the full ID is defined by the IDBLK and the IDNUM). The IDBLK is required for PU with Local XID handling or PU with End-to-End XID handling, NO Support for NON-Activation XID. Up to 3 Hexadeci…	OctetStringr/w	`.1.3.6.1.4.1.164.8.11.11.1.7`
pktSwchSnaPULlc2FrXIDIdNumS Second part of the IBM device ID (the full ID is defined by the IDBLK and the IDNUM). The IDNUM is required for PU with Local XID handling or PU with End-to-End XID handling, NO Support for NON-Activation XID. Up to 5 H…	OctetStringr/w	`.1.3.6.1.4.1.164.8.11.11.1.8`
pktSwchSnaPULlc2FrMaxPiuSizeS Maximum Path Information Size	Integer32r/w	`.1.3.6.1.4.1.164.8.11.11.1.9`
pktSwchSnaPULlc2FrTxWindowS The LLC2 Link Window Size.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.8.11.11.1.10`
pktSwchSnaPULlc2FrLinkS The SPS Frame Relay Link Number which this LLC2 Protocol Interface is associated with.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.8.11.11.1.11`
pktSwchSnaPULlc2FrDLCIS The SPS Frame Relay DLCI Number which this LLC2 Protocol Interface is associated with.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.8.11.11.1.12`
pktSwchSnaPULlc2FrXIDInitiationS This parameter is not applicable for PU with Local XID handling. Legal values: 1 - Do not initiate an XID message. 2 - Initiate an XID message to LLC2.	Enumerationr/w	`.1.3.6.1.4.1.164.8.11.11.1.13`
pktSwchSnaPULlc2FrN2CountS N2 Count	Integer32r/w	`.1.3.6.1.4.1.164.8.11.11.1.14`
pktSwchSnaPULlc2FrT1TimerS T1 Timer in 1/10 of a second.	Integer32r/w	`.1.3.6.1.4.1.164.8.11.11.1.15`
pktSwchSnaPULlc2FrTiTimerS TI Timer in seconds	Integer32r/w	`.1.3.6.1.4.1.164.8.11.11.1.16`
pktSwchSnaPULlc2FrEntryStatusS The status of this PU Llc2 table entry. In order to save this entry, set status to valid. An underCreation value is set by the Agent when this entry is updated.	Enumerationr/w	`.1.3.6.1.4.1.164.8.11.11.1.17`

pktSwchSnaPULlc2FrTableA

table

.1.3.6.1.4.1.164.8.11.12 · 1 row entry · 16 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchSnaPULlc2FrTableA

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchSnaPULlc2FrTableA'

Defines links for PUs running on an LLC2 link

pktSwchSnaPULlc2FrEntryA row .1.3.6.1.4.1.164.8.11.12.1

Defines parameters for PU LLC2 Protocol Interface over Frame Relay Protocol using RFC 1490.

Indexes

No indexes recorded

Column Syntax OID

pktSwchSnaPULlc2FrNumberA

Unique Identifier for this PU. The value in this field is used as a common Key in both this table and the Main PU table.

SNMPv2-SMIInteger32

Enumerated Values:

1	unbound
2	bindPending
3	unbindPend
4	idle
5	unattached
6	attachPend
7	detachPend
8	udqosPending
9	outconPend
10	inconPending
11	connResPend
12	dataxfer
13	userResetPend
14	provRstPend
15	rstResPend
16	discon8Pend
17	discon9Pend
18	discon11Pend
19	discon12Pend
20	discon13Pend
21	subsBindPend
22	noChange

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.11.12.1.1

pktSwchSnaPULlc2FrSideA

Indicates for each side (SIDE-A and SIDE-B) if the Protocol Interface for that side has been defined or not.

Enumeration

Enumerated Values:

1	linkClosed
2	disconnected
3	linkOpening
4	disconnecting
5	frmrSent
6	linkOpened
7	localBusy
8	rejection
9	checkpointing
10	cpLocalBusy
11	cpRejection
12	resetting
13	remoteBusy
14	lBusyRBusy
15	rejLBusy
16	rejRBusy
17	cpRejLBusy
18	cpClearing
19	cpRejClr
20	rejLbusyRbusy
21	frmrReceived
22	programError
23	noChange

.1.3.6.1.4.1.164.8.11.12.1.2

pktSwchSnaPULlc2FrEncapsTypeA

Indicates if the LLC2/RFC1490 Protocol Interface uses the BNN, BAN
or TREN method of Frame Encapsulation.

Enumeration

Enumerated Values:

1	sync
2	notSync

.1.3.6.1.4.1.164.8.11.12.1.3

pktSwchSnaPULlc2FrDestMACA

The LLC2 Destination MAC Address.

OctetString

Enumerated Values:

1	noRNR
2	txFlow
3	rxFlow
4	rxAndTx

.1.3.6.1.4.1.164.8.11.12.1.4

pktSwchSnaPULlc2FrSrcSAPA

The LLC2 Source SAP Address.

OctetString

.1.3.6.1.4.1.164.8.11.12.1.5

pktSwchSnaPULlc2FrDestSAPA

The LLC2 Destination SAP.

OctetString

.1.3.6.1.4.1.164.8.11.12.1.6

pktSwchSnaPULlc2FrXIDIdBlkA

Part of the IBM device ID (the full ID is defined by the IDBLK and
the IDNUM). The IDBLK is required for PU with Local XID handling
or PU with End-to-End XID handling, NO Support for NON-Activation XID.
Up to 3 Hexadeci…

OctetString

Enumerated Values:

3	bridging
4	ip
7	ip-and-bridging
8	llc
11	llc-and-bridging
12	ip-and-llc
15	all
255	none

.1.3.6.1.4.1.164.8.11.12.1.7

pktSwchSnaPULlc2FrXIDIdNumA

Second part of the IBM device ID (the full ID is defined by the IDBLK and
the IDNUM). The IDNUM is required for PU with Local XID handling
or PU with End-to-End XID handling, NO Support for NON-Activation XID.
Up to 5 H…

OctetString

Constraints:
range: 6-6

.1.3.6.1.4.1.164.8.11.12.1.8

pktSwchSnaPULlc2FrMaxPiuSizeA

Maximum Path Information Size

Integer32

.1.3.6.1.4.1.164.8.11.12.1.9

pktSwchSnaPULlc2FrTxWindowA

The LLC2 Link Window Size.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.11.12.1.10

pktSwchSnaPULlc2FrLinkA

The SPS Frame Relay Link Number which this LLC2 Protocol Interface is associated with.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.11.12.1.11

pktSwchSnaPULlc2FrDLCIA

The SPS Frame Relay DLCI Number which this LLC2 Protocol Interface is associated with.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.11.12.1.12

pktSwchSnaPULlc2FrXIDInitiationA

This parameter is not applicable for PU with Local XID handling.
Legal values:
1 - Do not initiate an XID message.
2 - Initiate an XID message to LLC2.

Enumeration

.1.3.6.1.4.1.164.8.11.12.1.13

pktSwchSnaPULlc2FrN2CountA

N2 Count

Integer32

.1.3.6.1.4.1.164.8.11.12.1.14

pktSwchSnaPULlc2FrT1TimerA

T1 Timer in 1/10 of a second.

Integer32

.1.3.6.1.4.1.164.8.11.12.1.15

pktSwchSnaPULlc2FrTiTimerA

TI Timer in seconds

Integer32

.1.3.6.1.4.1.164.8.11.12.1.16

pktSwchSnaPULlc2FrStatTable

table

.1.3.6.1.4.1.164.8.11.13 · 1 row entry · 32 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchSnaPULlc2FrStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchSnaPULlc2FrStatTable'

Shows link statistics for PUs running on an LLC2 link

pktSwchSnaPULlc2FrStatEntry row .1.3.6.1.4.1.164.8.11.13.1

Shows statistics for PU LLC2 Protocol Interface over Frame Relay Protocol using RFC 1490.

Indexes

No indexes recorded

Column Syntax OID

pktSwchSnaPULlc2FrStatNumber

Unique Identifier for this PU. The value in this field is used as a common Key in both this table and the Main PU table.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.8.11.13.1.1

pktSwchSnaPULlc2FrStatSide

Indicates for each side (SIDE-A and SIDE-B) if the Protocol Interface for that side has been defined or not.

Enumeration

.1.3.6.1.4.1.164.8.11.13.1.2

pktSwchSnaPULlc2FrStatOctetsIn

SNMPv2-SMICounter32

Constraints:
range: 1-10

.1.3.6.1.4.1.164.8.11.13.1.3

pktSwchSnaPULlc2FrStatOctetsOut

SNMPv2-SMICounter32

Constraints:
range: 6-6

.1.3.6.1.4.1.164.8.11.13.1.4

pktSwchSnaPULlc2FrStatIFramesIn

SNMPv2-SMICounter32

Enumerated Values:

256	llc
2048	ip
2054	arp
32923	appleTalk
65535	dontCare

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.5

pktSwchSnaPULlc2FrStatIFramesOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.6

pktSwchSnaPULlc2FrStatRRFramesIn

SNMPv2-SMICounter32

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.7

pktSwchSnaPULlc2FrStatRRFramesOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.8

pktSwchSnaPULlc2FrStatRNRFramesIn

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.9

pktSwchSnaPULlc2FrStatRNRFramesOut

SNMPv2-SMICounter32

Enumerated Values:

2	x25
3	frameRelay

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.10

pktSwchSnaPULlc2FrStatXIDsIn

SNMPv2-SMICounter32

Constraints:
range: 1-10

.1.3.6.1.4.1.164.8.11.13.1.11

pktSwchSnaPULlc2FrStatXIDsOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.12

pktSwchSnaPULlc2FrStatTESTsIn

SNMPv2-SMICounter32

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.13

pktSwchSnaPULlc2FrStatTESTsOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.14

pktSwchSnaPULlc2FrStatREJsIn

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.15

pktSwchSnaPULlc2FrStatREJsOut

SNMPv2-SMICounter32

Constraints:
range: 1-200

.1.3.6.1.4.1.164.8.11.13.1.16

pktSwchSnaPULlc2FrStatFRMRsIn

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.17

pktSwchSnaPULlc2FrStatFRMRsOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.18

pktSwchSnaPULlc2FrStatDISCsIn

SNMPv2-SMICounter32

Enumerated Values:

2	disable
3	enable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.19

pktSwchSnaPULlc2FrStatDISCsOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.20

pktSwchSnaPULlc2FrStatUAsIn

SNMPv2-SMICounter32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.11.13.1.21

pktSwchSnaPULlc2FrStatUAsOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.22

pktSwchSnaPULlc2FrStatDMsIn

SNMPv2-SMICounter32

Enumerated Values:

2	netIpAddress
255	none

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.23

pktSwchSnaPULlc2FrStatDMsOut

SNMPv2-SMICounter32

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.24

pktSwchSnaPULlc2FrStatSABMEsIn

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.25

pktSwchSnaPULlc2FrStatSABMEsOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.26

pktSwchSnaPULlc2FrStatRetransmitsIn

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.27

pktSwchSnaPULlc2FrStatRetransmitsOut

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.11.13.1.28

pktSwchSnaPULlc2FrStatUpperState

The internal DLPI state of the connection.

Enumeration

.1.3.6.1.4.1.164.8.11.13.1.29

pktSwchSnaPULlc2FrStatLowerState

The internal Llc2Fr state of the connection.

Enumeration

.1.3.6.1.4.1.164.8.11.13.1.30

pktSwchSnaPULlc2FrStatNRMStatus

This variable indicates if the link is in Normal Response Mode or not.

Enumeration

.1.3.6.1.4.1.164.8.11.13.1.31

pktSwchSnaPULlc2FrStatFlowCtlStatus

This variable indicates the flow control status of the PU interface.

Enumeration

.1.3.6.1.4.1.164.8.11.13.1.32

pktSwchEthernetLinkTable

table

.1.3.6.1.4.1.164.8.12.1 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchEthernetLinkTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchEthernetLinkTable'

The Ethernet link table defines the parameters in the PS
Ethernet links.

pktSwchEthernetLinkEntry row .1.3.6.1.4.1.164.8.12.1.1

The Ethernet Link Entry defines the contents of each link in the
Ethernet Link Table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchEthernetLinkOperationMode

This parameter shows the frame handling mode on this link.

When IP mode is defined, the IP frames received on this link
are handled and routed by the IP module in the PS.
If IP mode is disabled, the IP fr…

Enumerationr/w

.1.3.6.1.4.1.164.8.12.1.1.1

pktSwchEthernetLinkUserDefMacAddr

This parameter allows the user to define a different MAC address
for this link other than the device MAC address.
Possible values:
6 sets of 2 Hexadecimal digits with
spaces between them (XX XX XX XX XX XX)

OctetStringr/w

Constraints:
range: 1-200

.1.3.6.1.4.1.164.8.12.1.1.2

pktSwchEthernetLinkPointToPointDest

Destination of the frames which are received on this link.
Possible values:
X.25 PVC: Port:LCN
X.25 SVC: X.25 Addr or 'cid' followed by a predefined Call ID
number.
Frame Relay: Port:DLCI
…

SNMPv2-TCDisplayStringr/w

Enumerated Values:

2	bw56Kbps
3	bw64Kbps

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.12.1.1.3

pktSwchEthernetLinkTotalFramesIn

Total number of frames which were received on this link.

SNMPv2-SMICounter32

Enumerated Values:

1	noOptions
2	returnToMainLink

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.12.1.1.4

pktSwchEthernetLinkTotalFramesOut

Total number of frames which were transmitted from this link.

SNMPv2-SMICounter32

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.12.1.1.5

pktSwchEthernetLinkIpFramesIn

Number of IP frames which were received on this link.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.12.1.1.6

pktSwchEthernetLinkIpFramesOut

Number of IP frames which were transmitted from this link.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.12.1.1.7

pktSwchEthernetLinkLlc2FramesIn

Number of LLC2 frames which were received on this link.

SNMPv2-SMICounter32

Constraints:
range: 1-200

.1.3.6.1.4.1.164.8.12.1.1.8

pktSwchEthernetLinkLlc2FramesOut

Number of LLC2 frames which were transmitted from this link.

SNMPv2-SMICounter32

Constraints:
range: 1-3

.1.3.6.1.4.1.164.8.12.1.1.9

pktSwchEthernetLinkBridgFramesIn

Number of Bridged frames which were received on this link.

SNMPv2-SMICounter32

Constraints:
range: 0-17

.1.3.6.1.4.1.164.8.12.1.1.10

pktSwchEthernetLinkBridgFramesOut

Number of Bridged frames which were transmitted from this link.

SNMPv2-SMICounter32

Constraints:
range: 0-6

.1.3.6.1.4.1.164.8.12.1.1.11

pktSwchEthernetLinkDiscardedByFilter

Number of Bridged frames which were received on this link.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.12.1.1.12

pktSwchEthernetFilterTable

table

.1.3.6.1.4.1.164.8.12.2 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchEthernetFilterTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchEthernetFilterTable'

The Ethernet filter table defines the frame filtering and
routing through the PS Ethernet links.

pktSwchEthernetFilterEntry row .1.3.6.1.4.1.164.8.12.2.1

The Ethernet Filter Entry defines the filtering on each Ethernet
link. The filter entry is operational only if Bridging Handling
is enabled and there is no point to point destination configured
for this link. If there i…

Indexes

No indexes recorded

Column Syntax OID

pktSwchEthernetFilterId

Identification Number of an entry in the filter table.
The ID together with the ifindex define an entry.

Integer32

Constraints:
range: 1-255

.1.3.6.1.4.1.164.8.12.2.1.1

pktSwchEthernetFilterMacAddr

This parameter defines the MAC address in the current entry
of the filter table.
The MAC address in the filter table is compared with the MAC
address in the received frame. If the MAC address and protocol
type of the fr…

OctetStringr/w

Constraints:
range: 0-6

.1.3.6.1.4.1.164.8.12.2.1.2

pktSwchEthernetFilterProtType

The protocol type which is compared with the protocol type
in the received frame. Each protocol in the IP frame is assigned
16 bits (see RFC1700.txt on the assignment of protocol parameters
for the Internet protocol sui…

Enumerationr/w

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

.1.3.6.1.4.1.164.8.12.2.1.3

pktSwchEthernetFilterDest

Destination of the frames which match this current entry.
The match is in the MAC address and protocol.

Possible values:
X.25 PVC: Port:LCN
X.25 SVC: X.25 Addr or 'cid' followed by a predefined Ca…

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.12.2.1.4

pktSwchEthernetFilterStatus

The status of this filter table entry.
valid - This entry was saved.
createRequest - Request to create a new entry.
underCreation - For a new/updated entry.
invalid - Entry is deleted.

Enumerationr/w

.1.3.6.1.4.1.164.8.12.2.1.5

pktSwchEthernetBroadcastDestTable

table

.1.3.6.1.4.1.164.8.12.4 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchEthernetBroadcastDestTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchEthernetBroadcastDestTable'

The Ethernet Broadcast Destination table defines all the Bridging
destinations of the PS. Each Broadcasted frame will be
broadcasted to all these destinations.

pktSwchEthernetBroadcastDestEntry row .1.3.6.1.4.1.164.8.12.4.1

The Ethernet Broadcast Entry defines destinations for Ethernet
bridge data.

Indexes

No indexes recorded

Column Syntax OID

pktSwchEthernetBroadcastDestProtocol

The protocol of the Broadcasted frames.

Enumeration

Enumerated Values:

2	noOp
3	activate

.1.3.6.1.4.1.164.8.12.4.1.1

pktSwchEthernetBroadcastDestId

Identification Number of an entry in the Ethernet Broadcast
Destination table.

Integer32

Constraints:
range: 0-17

.1.3.6.1.4.1.164.8.12.4.1.2

pktSwchEthernetBroadcastDestDestination

Destination for the Ethernet frames.

Possible values for X25:
X.25 PVC: Port:LCN
X.25 SVC: X.25 Addr or 'cid' followed by a predefined Call ID number

Possible values for fr:
Frame R…

SNMPv2-TCDisplayStringr/w

Constraints:
range: 0-6

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.12.4.1.3

pktSwchEthernetBroadcastDestStatus

The status of this Ethernet Destination table entry.
valid - This entry was saved.
createRequest - Request to create a new entry.
underCreation - For a new/updated entry.
invalid - Entry is deleted.

Enumerationr/w

.1.3.6.1.4.1.164.8.12.4.1.4

pktSwchIpInterfaceTable

table

.1.3.6.1.4.1.164.8.13.2 · 1 row entry · 18 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchIpInterfaceTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchIpInterfaceTable'

The Ip interface table defines the Ip interfaces and their
parameters in the PS device.

pktSwchIpInterfaceEntry row .1.3.6.1.4.1.164.8.13.2.1

The IP interface Entry defines the IP configuration parameters
for each IP interface.

Indexes

No indexes recorded

Column Syntax OID

pktSwchIpInterfaceId

Identification Number of an entry in the IP interface table.

Integer32

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

.1.3.6.1.4.1.164.8.13.2.1.1

pktSwchIpInterfaceAddress

The IP address of the interface. Legal input: any legal IP address.
Default value: 0.0.0.0

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.8.13.2.1.2

pktSwchIpInterfaceAddressMask

The IP mask of the interface. Legal input: any legal IP mask:
A string of the format X.X.X.X where every X is a number in
the range 0-255.
Default value: 255.255.255.255

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.8.13.2.1.3

pktSwchIpInterfaceSendDefRoutMsgOnly

Some of the RIP messages are default router messages.
These messages inform who the default router is.

This MIB object allows the user to configure the device so
that it will send default router messages …

Enumerationr/w

Enumerated Values:

1	s110bps
2	s300bps
3	s1200bps
4	s600bps
5	s75bps
6	s150bps
12	s2400bps
13	s4800bps
14	s9600bps
15	s19200bps
19	s38400bps
20	s57600bps
21	s115200bps
255	notApplicable

.1.3.6.1.4.1.164.8.13.2.1.4

pktSwchIpInterfaceDest

Destination of the packets received on this interface.

Possible values:
X.25 PVC: Port:LCN
X.25 SVC: X.25 Addr or 'cid' followed by a predefined Call ID
number.
Frame Relay: …

SNMPv2-TCDisplayStringr/w

Constraints:
range: 0-255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.8.13.2.1.5

pktSwchIpInterfaceInactivity

Inactivity time in minutes before disconnecting the X25 SVC call.
Range: 0..255. Default: 2.

Integer32r/w

Enumerated Values:

1	one
2	two
3	oneAndHalf
255	notApplicable

.1.3.6.1.4.1.164.8.13.2.1.6

pktSwchIpInterfaceLinkCost

This value will be added to the value written in the
metric field of the received frame.
Range: 1..pktSwchIpGlobalMaxHopCount
Default: 1.

SNMPv2-SMIInteger32r/w

Constraints:
range: 0-8

.1.3.6.1.4.1.164.8.13.2.1.7

pktSwchIpInterfaceOptions

When netIpAddress is selected the interface IP address
will not be the IP address of the interface. It will be the IP
address of the NetWork which is connected to this interface.
This option is for an interface which do…

Enumerationr/w

Enumerated Values:

1	space
2	mark
3	even
4	odd
255	none

.1.3.6.1.4.1.164.8.13.2.1.8

pktSwchIpInterfaceStatus

The status of this filter table entry.
valid - This entry was saved.
createRequest - Request to create a new entry.
underCreation - For a new/updated entry.
invalid - Entry is deleted.

Enumerationr/w

Enumerated Values:

1	hw-signal
2	data-triggered
3	hw-signal-or-data
255	after-reset

.1.3.6.1.4.1.164.8.13.2.1.9

pktSwchIpInterfaceRxFrames

No. of frames which were received on this IP interface.

SNMPv2-SMICounter32

Constraints:
range: 1500-4096

.1.3.6.1.4.1.164.8.13.2.1.10

pktSwchIpInterfaceRxExpiredTtl

No. of frames which were received on this IP interface
with an Expired Time to Live value.

SNMPv2-SMICounter32

Constraints:
range: 4-4

.1.3.6.1.4.1.164.8.13.2.1.11

pktSwchIpInterfaceRxUnknownDest

No. of frames which were received on this IP interface
with an unknown IP destination. No default router is configured.
These frames will be discarded.

SNMPv2-SMICounter32

Enumerated Values:

1	no-authentication
2	pap-or-chap
3	chap-only

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.13.2.1.12

pktSwchIpInterfaceTxFrames

No. of frames which were Transmitted from this IP interface.

SNMPv2-SMICounter32

Enumerated Values:

1	r3000bps
2	r4800bps
3	r9600bps
4	r14400bps
5	r19200bps
6	r38400bps
7	r48Kbps
8	r56Kbps
9	r64Kbps
10	r128Kbps
11	r256Kbps
12	r384Kbps
13	r512Kbps
14	r768Kbps
15	r1024Kbps
16	r1445Kbps
17	r2048Kbps
255	external

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.8.13.2.1.13

pktSwchIpInterfaceTxQueueBufs

No. of buffers which are waiting in the Trasnsmit Queue.

SNMPv2-SMICounter32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.13.2.1.14

pktSwchIpInterfaceTxDiscarded

No. of frames which were ready to be transmitted but were
Discarded. The PS will discard frames if the transmit queue
is too long.

SNMPv2-SMICounter32

Constraints:
range: 0-200

.1.3.6.1.4.1.164.8.13.2.1.15

pktSwchIpInterfaceRipRxFrames

No. of RIP frames which were received on this IP interface.

SNMPv2-SMICounter32

Constraints:
range: 0-80

.1.3.6.1.4.1.164.8.13.2.1.16

pktSwchIpInterfaceRipTxFrames

No. of RIP Frames which were transmitted from this IP interface.

SNMPv2-SMICounter32

Constraints:
range: 0-29

.1.3.6.1.4.1.164.8.13.2.1.17

pktSwchIpInterfaceRipWaitingMsgs

No. of RIP messages which are waiting to be transmitted to the
Network.

SNMPv2-SMICounter32

Constraints:
range: 0-29

.1.3.6.1.4.1.164.8.13.2.1.18

pktSwchIsdnRoutTable

table

.1.3.6.1.4.1.164.8.14.2 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchIsdnRoutTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchIsdnRoutTable'

The Isdn Routing Table entries in the Packet Switch.

pktSwchIsdnRoutEntry row .1.3.6.1.4.1.164.8.14.2.1

Isdn Routing Entry defines the contents of each entry in the table.
The outgoing addresses are in a different table -
pktSwchIsdnRoutAddrTable. The row status in this
table will be used for both tables.

Indexes

etRptrIndex

Column Syntax OID

pktSwchIsdnRoutId

Number of this routing entry.

Integer32

.1.3.6.1.4.1.164.8.14.2.1.1

pktSwchIsdnRoutDataBandWidth

Isdn Bandwidth which will be used for the data routed via this
entry. The ISDN interface will be configured with the speed
which is selected.
Possible values:
2 - 56 Kbps.
3 - 64 Kbps.
Default value: 3

Enumerationr/w

Constraints:
range: 1-1024

.1.3.6.1.4.1.164.8.14.2.1.2

pktSwchIsdnRoutOptions

Special Options for this routing entry.
Possible values:
1 - No special options.
2 - Return to main link. This option is used when the current link
is defined as a backup link and the main link becomes active.
Defau…

Enumerationr/w

Enumerated Values:

1	other
2	ok
3	rptrFailure
4	groupFailure
5	portFailure
6	generalFailure

.1.3.6.1.4.1.164.8.14.2.1.3

pktSwchIsdnRoutStatus

The status of this routing table entry + address table
(pktSwchIsdnOutAddrTable).
For creating a new entry select createRequest. A new route entry
will be created together with an out address entry. There may be
more th…

Enumerationr/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.8.14.2.1.4

pktSwchIsdnOutAddrTable

table

.1.3.6.1.4.1.164.8.14.3 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchIsdnOutAddrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchIsdnOutAddrTable'

Outgoing ISDN addresses used by the ISDN routing table.
The address table contains outgoing
addresses and alternative addresses in case the connection
to the first addresses does not succeed.

pktSwchIsdnOutAddrEntry row .1.3.6.1.4.1.164.8.14.3.1

Isdn Outgoing Address Entry defines the contents of each entry in
the outgoing address table.
Each entry has 2 indices:
1. RoutId is the ID in the routing table.
2. AddrId is the ID containing the Outgoing address and
…

Indexes

No indexes recorded

Column	Syntax	OID
pktSwchIsdnOutAddrRoutId ID in the ISDN routing table.	Integer32	`.1.3.6.1.4.1.164.8.14.3.1.1`
pktSwchIsdnOutAddrId Number of the address + subaddress pair for each routing ID.	Integer32	`.1.3.6.1.4.1.164.8.14.3.1.2`
pktSwchIsdnOutAddr Destination ISDN Outgoing (Remote) address. The data will be routed out to this address. Possible values: Up to 17 decimal digits. Default value: string of length 0.	OctetStringr/w	`.1.3.6.1.4.1.164.8.14.3.1.3`
pktSwchIsdnOutSubAddr Destination ISDN Outgoing (Remote) sub address. The data will be routed out to the out addrress with this sub address. Possible values: Up to 6 decimal digits. Default value: string of length 0.	OctetStringr/w	`.1.3.6.1.4.1.164.8.14.3.1.4`

pktSwchIsdnAcceptTable

table

.1.3.6.1.4.1.164.8.14.4 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchIsdnAcceptTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchIsdnAcceptTable'

Table of Isdn addresses which will be accepted by the agent.
If there is a dial back (answer) address, the incoming call
will be disconnected and dial back will initiate. Most of
the accept list parameters are in RFC2128 in the
dialCtlPeerCfgTable. The parameters which are not in the
the standard RFC2128 and are required, are defined here
in the private PS MIB.

pktSwchIsdnAcceptEntry row .1.3.6.1.4.1.164.8.14.4.1

Isdn Accept Entry defines the contents of each entry in the table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchIsdnAcceptId

Identifier of Accept table entry.

Integer32

Constraints:
range: 1-3

.1.3.6.1.4.1.164.8.14.4.1.1

pktSwchIsdnAcceptSecondaryLink

A valid Isdn link number on which the call will be accepted
when the Primary link (RFC2128.dialCtlPeerCfgLowerIf)is unavailable.

Possible values:
255 - No Secondary link.
or
The complementary to the prima…

Integer32r/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.8.14.4.1.2

pktSwchIsdnAcceptDialbkSubAddress

Isdn sub address which will be used by the agent for dialing
back.
Possible values:
Up to 6 decimal digits.

Default value: string of length 0.

OctetStringr/w

.1.3.6.1.4.1.164.8.14.4.1.3

pktSwchIsdnAcceptStatus

The status of this accept table entry.
For creating a new entry select createRequest,
For deleting an entry select invalid.
For saving an entry select valid.

Enumerationr/w

.1.3.6.1.4.1.164.8.14.4.1.4

pktSwchIsdnLinkTable

table

.1.3.6.1.4.1.164.8.14.5 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchIsdnLinkTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchIsdnLinkTable'

Table of Isdn Link parameters. Most of the link parameters
are in in RFC2127. Isdn Call statistics are RFC2128.
The parameters which are not in the the standard RFCs ,
and are required, are defined here in the private PS MIB.

pktSwchIsdnLinkEntry row .1.3.6.1.4.1.164.8.14.5.1

Isdn Link Entry defines the contents of each entry in the table.

Indexes

mplsIngressTunnelIndex

Column	Syntax	OID
pktSwchIsdnLinkBchannel Defines which B channels are used for Leased Lines Only. Default value: noBchannel(1).	Enumerationr/w	`.1.3.6.1.4.1.164.8.14.5.1.1`
pktSwchIsdnCallsClrs Number of calls on this link which were cleared since the link was activated.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.8.14.5.1.2`
pktSwchIsdnTestCmd Activate/Stop an ISDN test on the current ISDN link. In order to Activate the test, set the TestCmd to 3 (activate). For stopping the test, set the TestCmd to 2 (noOp). Important: In order for the test to…	Enumerationr/w	`.1.3.6.1.4.1.164.8.14.5.1.3`
pktSwchIsdnTestAddr Destination ISDN Outgoing (Remote) address which will be called in order to test the ISDN. Possible values: Up to 17 decimal digits. Default value: string of length 0. Important: In order for the test to …	OctetStringr/w	`.1.3.6.1.4.1.164.8.14.5.1.4`
pktSwchIsdnTestSubAddr Destination ISDN Outgoing (Remote) address which will be called in order to test the ISDN. Possible values: Up to 6 decimal digits. Default value: string of length 0. Important: In order for the test to s…	OctetStringr/w	`.1.3.6.1.4.1.164.8.14.5.1.5`

pktSwchPppSecretsTable

table

.1.3.6.1.4.1.164.8.15.1 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchPppSecretsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchPppSecretsTable'

Table of PPP Secret parameters.
The parameters are defined in rfc1472 except for the ROW status
which is defined here.
In the standard, there is no create request option, so in order
to be consistent with other ROW statuses in the Packet Switches
it is defined here.

pktSwchPppSecretsEntry row .1.3.6.1.4.1.164.8.15.1.1

PPP Secrets Entry defines the contents of each entry in the table.

Indexes

No indexes recorded

Column	Syntax	OID
pktSwchPppSecretsPairId Index of the Secrets Pair.	Integer32	`.1.3.6.1.4.1.164.8.15.1.1.1`
pktSwchPppSecretsStatus The status of the PPP Secrets table. For creating a new entry select createRequest, For deleting an entry select invalid. For saving an entry select valid.	Enumerationr/w	`.1.3.6.1.4.1.164.8.15.1.1.2`

pktSwchPppChanTable

table

.1.3.6.1.4.1.164.8.15.2 · 1 row entry · 15 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pktSwchPppChanTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pktSwchPppChanTable'

Table of PPP Channel parameters.
The table can be used for Async as well as Sync parameters.
In case a parameter is irrelevant for Async or Sync a <not
applicable> value may be returned.
Statistics Parameters are already defined in rfc1213:
ifInUcastPkts, ifOutUcastPkts, ifInErrors, ifOutErrors

pktSwchPppChanEntry row .1.3.6.1.4.1.164.8.15.2.1

PPP Channel Entry defines the contents of each entry in the table.

Indexes

No indexes recorded

Column Syntax OID

pktSwchPppChanSpeed

The port's speed in bits per second.
For Async channels: Default value: 14 .
For Sync Links: Use not_applicable(255)
The Sync Links have an internal clock with
different values.

Enumerationr/w

.1.3.6.1.4.1.164.8.15.2.1.1

pktSwchPppChanFlowCtlDuration

Hardware Flow Control Duration.
1..254 - Duration (in 50ms intervals).
when timer expires, flow control stops.
0 - No Hardware flow control.
255 - Continuous Flow Control.
Default value: 0.
For Sync Lin…

Integer32r/w

.1.3.6.1.4.1.164.8.15.2.1.2

pktSwchPppChanStopBits

This entry indicates the number of stop bits per character.
The options are either (1) one stop bit, (2) two stop bits,
or (3) 1.5 stop bits.
For Sync Links: notApplicable(255).

Enumerationr/w

.1.3.6.1.4.1.164.8.15.2.1.3

pktSwchPppChanBitPerChar

The number of data bits per character supported by the ppp
link. Legal values for Async channels: 5..8 .
For Sync Links: 0

Integer32r/w

.1.3.6.1.4.1.164.8.15.2.1.4

pktSwchPppChanParity

This entry selects the type of parity to be checked or
generated.
The options are (1) space parity, (2) mark parity,
(3) even parity, (4) odd parity, or (255) no parity.
For Sync Links: none(255).

Enumerationr/w

.1.3.6.1.4.1.164.8.15.2.1.5

pktSwchPppChanNegotiationTrigger

The trigger which is used in order to start the Negotiation.
The HW signals which are used are:
DCD (Data Carrier Detect) - issued by DCE
DSR (Data Set Ready) - issued by DCE
DTR (Data Terminal Ready) - issued b…

Enumerationr/w

.1.3.6.1.4.1.164.8.15.2.1.6

pktSwchPppChanMRU

Maximum Receive Unit.
Size of the packet which is negotiated with the connected device.

Default value: 1500 .

Integer32r/w

Enumerated Values:

1	notApplicable
2	atmVc
3	bridgePort
4	ipV4

.1.3.6.1.4.1.164.8.15.2.1.7

pktSwchPppChanACCM

Async Control Character Map -
The ACCM value serves as a mask for the first 32 characters
in the ASCII table.

Control characters may cause problems when they are transferred
on the network. This can be ha…

OctetStringr/w

.1.3.6.1.4.1.164.8.15.2.1.8

pktSwchPppChanAuthentication

Port Authentication Type.
1 - No Authentication: User side Only.
2 - Configuration of the Host side.
PAP (Password Authentication Protocol) or
CHAP (Challenge Handshake Authentication Protocol)
will be accep…

Enumerationr/w

.1.3.6.1.4.1.164.8.15.2.1.9

pktSwchPppChanInternalClock

The internal clock rate of the MLPPP Link.
Default value: 9.
For Async channels: return 255.

Enumerationr/w

.1.3.6.1.4.1.164.8.15.2.1.10

pktSwchPppChanBundle

Bundle Number.
It is possible to attach a few channels/links to a bundle.
If the User enters a non existing bundle number, the PS will
create a new bundle with this number.
The bundle number may be: 1..255
If the bundle…

Integer32r/w

Enumerated Values:

1	up
2	down
3	testing

.1.3.6.1.4.1.164.8.15.2.1.11

pktSwchpPppChanIsdnRoutId

ISDN destination. ID (1..200) in the ISDN routing table containing
the outgoing ISDN address for this channel/link.

For no destination: 0
Default value: 0

Integer32r/w

.1.3.6.1.4.1.164.8.15.2.1.12

pktSwchpPppChanLastEvent

Status showing the last PPP event which occured on the line
described in an ascii string.
Examples:
1. Received Configuration Request.
2. Sent Protocol Reject.
3. Error: Can Not Compress Frame.

Default: 0…

OctetString

.1.3.6.1.4.1.164.8.15.2.1.13

pktSwchpPppChanModemInitString

This string is needed by the modem in order to be initiated,
before dialing.

OctetStringr/w

.1.3.6.1.4.1.164.8.15.2.1.14

pktSwchpPppChanModemDialString

This string enables the modem to open a new call.

OctetStringr/w

.1.3.6.1.4.1.164.8.15.2.1.15

etRptrTable

table

.1.3.6.1.4.1.164.9.1 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk etRptrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::etRptrTable'

This table contains repeater data specific to the etRptrIndex.

etRptrEntry row .1.3.6.1.4.1.164.9.1.1

An entry in table etRptrTable.

Indexes

No indexes recorded

Column Syntax OID

etRptrIndex

The Repeater Id, this table data refer to.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.9.1.1.1

etRptrGroupCapacity

The etRptrGroupCapacity is the number of groups
that can be contained within the repeater. Within
each managed repeater, the groups are uniquely
numbered in the range from 1 to etRptrGroupCapacity.

Some …

Integer32

Enumerated Values:

1	up
2	down

.1.3.6.1.4.1.164.9.1.1.2

etRptrOperStatus

The etRptrOperStatus object indicates the
operational state of the repeater. The
etRptrHealthText object may be consulted for more
specific information about the state of the
repeater's health.
In the case of multiple …

Enumeration

.1.3.6.1.4.1.164.9.1.1.3

etRptrHealthText

The health text object is a text string that
provides information relevant to the operational
state of the repeater. Agents may use this string
to provide detailed information on current
failures, including how they we…

OctetString

.1.3.6.1.4.1.164.9.1.1.4

etRptrReset

Setting this object to reset(2) causes a
transition to the START state of Fig 9-2 in
section 9 [IEEE 802.3 Std].

Setting this object to noReset(1) has no effect.
The agent will always return the value noR…

Enumerationr/w

.1.3.6.1.4.1.164.9.1.1.5

etRptrNonDisruptTest

Setting this object to selfTest(2) causes the
repeater to perform a agent-specific, non-
disruptive self-test that has the following
characteristics: a) The nature of the tests is
not specified. b) The test does not c…

Enumerationr/w

.1.3.6.1.4.1.164.9.1.1.6

etRptrTotalPartitionedPorts

This object returns the total number of ports in
the repeater whose current state meets all three
of the following criteria: etRptrPortOperStatus
does not have the value notPresent(3),
etRptrPortAdminStatus is enabled(…

SNMPv2-SMIGauge32

Enumerated Values:

1	enable
2	disable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.9.1.1.7

etRptrMdlVector

This object returns a vector mapping the location of the repeater modules
to their corresponding bit position. A bit that is set indicates an existing module

SNMPv2-SMIInteger32r/w

Constraints:
range: 1-65535

.1.3.6.1.4.1.164.9.1.1.8

etRptrMonitorTransmitCollisions

This counter is incremented every time the
repeater state machine enters the TRANSMIT
COLLISION state from any state other than ONE PORT
LEFT (Ref: Fig 9-2, IEEE 802.3 Std).

The approximate minimum time f…

SNMPv2-SMICounter32

Constraints:
range: 0-65535

.1.3.6.1.4.1.164.9.1.1.9

etRptrSecTable

table

.1.3.6.1.4.1.164.9.2 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk etRptrSecTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::etRptrSecTable'

Repeater Security Table

etRptrSecEntry row .1.3.6.1.4.1.164.9.2.1

An entry in table etRptrSecTable.

Indexes

No indexes recorded

Column	Syntax	OID
etRptrId The Repeater Id, this table data refer to.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.9.2.1.1`
etRptrSecID Segment's security unique identification number	Integer32	`.1.3.6.1.4.1.164.9.2.1.2`
etRptrSecEnable This entry indicates whether the specific segment's security is active or not	Enumerationr/w	`.1.3.6.1.4.1.164.9.2.1.3`
etRptrSecPattern A six-octet(48 bit) pattern: where the masked bits of etRptrSecMask need to match the MAC address of each port within the segment.Value of all zeros indicates no security.	OctetStringr/w	`.1.3.6.1.4.1.164.9.2.1.4`
etRptrSecMask Mask of the allowed MAC address that can be connected through the ports within the segment	OctetStringr/w	`.1.3.6.1.4.1.164.9.2.1.5`

mplsIngressTunnelTable

table

.1.3.6.1.4.1.164.10.1.6 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mplsIngressTunnelTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mplsIngressTunnelTable'

The mpls Ingress Tunnel Table

mplsIngressTunnelEntry row .1.3.6.1.4.1.164.10.1.6.1

An entry in this table represents an MPLS tunnel.
An entry can be created by a network administrator
or by an SNMP agent as instructed by an MPLS
signaling protocol.

Indexes

rtrIfCfgIndex rtrIfCfgIpAddress

Column Syntax OID

mplsIngressTunnelIndex

Ingress Tunnel index.

MPLS-TC-STD-MIBMplsTunnelIndex

Type Constraints:
range: 0..65535

.1.3.6.1.4.1.164.10.1.6.1.1

mplsIngressTunnelName

The name assigned to the ingress tunnel.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.10.1.6.1.2

mplsIngressTunnelOwner

Denotes the entity (or protocol) that created and is responsible
for managing this tunnel.

MPLS-TC-STD-MIBMplsOwnerr/w

Type Values:

1	unknown
2	other
3	snmp
4	ldp
5	crldp
6	rsvpTe
7	policyAgent

.1.3.6.1.4.1.164.10.1.6.1.3

mplsIngressTunnelAttachedInterface

The incoming interface leads
to a predefined ifindex based on connection type.

IF-MIBInterfaceIndexOrZeror/w

Type Constraints:
range: 0..2147483647

Description:

.1.3.6.1.4.1.164.10.1.6.1.4

mplsIngressTunnelNumberOfLabels

The number of tunnel labels that should be received
on this ingress tunnel.
This number does not include the pW label

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.10.1.6.1.5

mplsIngressTunnelAdminStatus

Indicates the desired operational status of this
tunnel.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	atm
3	lis
4	ethernet

.1.3.6.1.4.1.164.10.1.6.1.6

mplsIngressTunnelOuterLabel

The Label that is 'closer' to the network encapsulation.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.10.1.6.1.7

mplsIngressTunnelInnerLabel

The Label that is 'closer' to the user payload.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.10.1.6.1.8

mplsIngressTunnelRowStatus

Object used for creating, modifying, and deleting
a row of this table

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.10.1.6.1.9

mplsIngressTunnelPWCounter

The number of Pseudo Wires that use the ingress tunnel.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.10.1.6.1.10

mplsIngressTunnelOperStatus

Indicates the operational status of this ingress tunnel.

Enumeration

Enumerated Values:

1	notApplicable
2	untag
3	tag

.1.3.6.1.4.1.164.10.1.6.1.11

mplsEgressTunnelTable

table

.1.3.6.1.4.1.164.10.1.8 · 1 row entry · 17 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk mplsEgressTunnelTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::mplsEgressTunnelTable'

The mpls Egress Tunnel Table

mplsEgressTunnelEntry row .1.3.6.1.4.1.164.10.1.8.1

An entry in this table represents an MPLS tunnel.
An entry can be created by a network administrator
or by an SNMP agent as instructed by an MPLS
signalling protocol.

Indexes

No indexes recorded

Column Syntax OID

mplsEgressTunnelIndex

Egress Tunnel index .

MPLS-TC-STD-MIBMplsTunnelIndex

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: 0..65535

.1.3.6.1.4.1.164.10.1.8.1.1

mplsEgressTunnelName

The name assigned to the egress tunnel.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Enumerated Values:

1	notApplicable
2	bridgedPdu
3	routedPdu

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.10.1.8.1.2

mplsEgressTunnelOwner

Denotes the entity (or protocol) that created and is responsible
for managing this tunnel.

MPLS-TC-STD-MIBMplsOwnerr/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.10.1.8.1.3

mplsEgressTunnelAttachedInterface

The outgoing interface leads
to a predefined ifindex based on connection type.

IF-MIBInterfaceIndexOrZeror/w

Type Constraints:
range: 0..2147483647

Description:

.1.3.6.1.4.1.164.10.1.8.1.4

mplsEgressTunnelNextHopType

Indicates address type of the Next Hop.
Not applicable for device with router.

Enumerationr/w

.1.3.6.1.4.1.164.10.1.8.1.5

mplsEgressTunnelNextHop

Not applicable (=0) when mplsEgressTunnelNextHopType=notApplicable.
When applicable, represents ATM VC, Bridge Port,
according to mplsEgressTunnelNextHopType.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.10.1.8.1.6

mplsEgressTunnelIpNextHop

Applicable only when mplsEgressTunnelNextHopType =ipV4.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.10.1.8.1.7

mplsEgressTunnelNumberOfLabels

Number of Tunnel Labels that should be transmitted
on this egress LSP (Labeled-Switched Path).
This number of labels does not include the PW number.
Valid values 0 - no label, 1, 2

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.10.1.8.1.8

mplsEgressTunnelAdminStatus

Indicates the desired operational status of this
egress tunnel.

Enumerationr/w

Enumerated Values:

1	enable
2	disable

.1.3.6.1.4.1.164.10.1.8.1.9

mplsEgressTunnelOuterLabel

The Label that is 'closer' to the network encapsulation.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.10.1.8.1.10

mplsEgressTunnelInnerLabel

The Label that is 'closer' to the user payload.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.10.1.8.1.11

mplsEgressTunnelRowStatus

Object used for creating, modifying, and deleting
a row of this table

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.10.1.8.1.12

mplsEgressTunnelPWCounter

The number of Pseudo Wires that use the egress tunnel.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.10.1.8.1.13

mplsEgressTunnelPeerIdx

Represents the Index of the Peer (as it is defined in the Peer Table),
for which this egress tunnel should be established.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.10.1.8.1.14

mplsEgressTunnelExpBitsMode

Indicates the EXP Bits Mode of this egress tunnel:

copyFromPw(2)- EXP Bits of this tunnel are copied from the EXP bits
of the PW, as configured for the PW.

static(3) - EXP Bits value…

Enumerationr/w

.1.3.6.1.4.1.164.10.1.8.1.15

mplsEgressTunnelExpBits

Indicates the EXP Bits of this egress tunnel.
Relevant only when EXP Bits Mode is 'static(3)'.

SNMPv2-SMIUnsigned32r/w

Constraints:
range: 4-1800

.1.3.6.1.4.1.164.10.1.8.1.16

mplsEgressTunnelOperStatus

Indicates the operational status of this egress tunnel.

Enumeration

Constraints:
range: 3-1800

.1.3.6.1.4.1.164.10.1.8.1.17

radMplsLdpEntityTable

table

.1.3.6.1.4.1.164.10.2.1.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk radMplsLdpEntityTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::radMplsLdpEntityTable'

This table contains information about the
MPLS Label Distribution Protocol Entities which
exist on this Label Switching Router (LSR)
or Label Edge Router (LER).

radMplsLdpEntityEntry row .1.3.6.1.4.1.164.10.2.1.1.1

An entry in this table represents an LDP entity.
An entry can be created by a network administrator
or by an SNMP agent as instructed by LDP.

Indexes

No indexes recorded

Column Syntax OID

radMplsLdpEntityLdpId

The LDP identifier.
When irrelevant, value = (2^48)-1 (all ones in all 6 octets).

MPLS-TC-STD-MIBMplsLdpIdentifier

Type Constraints:
range: 6

.1.3.6.1.4.1.164.10.2.1.1.1.1

radMplsLdpEntityIndex

This index is used as a secondary index to uniquely
identify this row.

A secondary index (this object) is meaningful to some
but not all, LDP implementations. For example
an LDP implementation which uses…

DIFFSERV-MIBIndexInteger

Type Constraints:
range: 1..4294967295

.1.3.6.1.4.1.164.10.2.1.1.1.2

radMplsLdpEntityAdminStatus

The administrative status of this LDP Entity.
If this object is changed from 'enable' to 'disable'
and this entity has already attempted to establish
contact with a Peer, then all contact with that
Peer is lost and all …

Enumerationr/w

.1.3.6.1.4.1.164.10.2.1.1.1.4

radMplsLdpEntityKeepAliveHoldTimer

The 16-bit integer value which is the proposed keep
alive hold timer for this LDP Entity.

secondsUnsigned32r/w

.1.3.6.1.4.1.164.10.2.1.1.1.9

radMplsLdpEntityHelloHoldTimer

The 16-bit integer value which is the proposed Hello
hold timer for this LDP Entity. The Hello Hold time
in seconds.

An LSR maintains a record of Hellos received
from potential peers. This object represe…

secondsUnsigned32r/w

.1.3.6.1.4.1.164.10.2.1.1.1.10

radMplsLdpEntityRowStatus

The status of this conceptual row. All writable
objects in this row may be modified at any
time, however, as described in detail in
the section entitled, 'Changing Values After
Session Establishment', and again describ…

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.10.2.1.1.1.23

rtrConfigIfTable

table

.1.3.6.1.4.1.164.11.1.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk rtrConfigIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::rtrConfigIfTable'

Table of configured interfaces.

rtrConfigIfEntry row .1.3.6.1.4.1.164.11.1.1.1

Each entry defines a configured interface.

Indexes

No indexes recorded

Column Syntax OID

rtrConfigIfIndex

This variable uniquely identifies the interface.
It is used as a cross reference in other system tables

IF-MIBInterfaceIndex

Type Constraints:
range: 1..2147483647

Description:

.1.3.6.1.4.1.164.11.1.1.1.1

rtrConfigIfType

This variable identifies the type of the specific
entry in the rtrDynamicIfConfigTable.
This field is writable only at creation time
(i.e., when value of status is underCreation).

RtrIfConfigTYPEr/w

Type Values:

1	other
6	ethernetLan
7	iso88023Csmacd
9	tokenRingLan
15	fddi
20	basicISDN
21	primaryISDN
22	propPointToPoint
23	ppp
28	slip
32	frameRelay
33	rs232
37	atm
40	x25ple
45	v35
62	fastEther
69	fastEtherFX
500	virtualNet
1001	cod
1002	backUp
1004	dialUp
1010	b1isdn
1011	b2isdn
1020	ipBcst
1021	ipPtp
1022	ipxRaw
1023	ipxEtType
1024	ipxLlcSap
1025	ipxLlcSnap
1026	ipxPtp
1027	brgUnder
1060	wanDriver
1061	ethernetDriver
1062	tokenRingDriver
1064	fddiDriver
1080	virtualLan
1100	unknown

.1.3.6.1.4.1.164.11.1.1.1.2

rtrConfigIfName

This variable provides a logical name to a specific entry in
rtrConfigIfTable. It is also used in identifying the Driver
interfaces.

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.11.1.1.1.3

rtrConfigIfStatus

The status of the ConfigEntry. The choices are those
defined in SNMPv2-TC. Only: active, createAndWait, and destroy
will be used.
active - The conceptual row is available for use by the managed device.
createAndWait -…

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.11.1.1.1.4

rtrIfCfgTable

table

.1.3.6.1.4.1.164.11.1.2 · 1 row entry · 16 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk rtrIfCfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::rtrIfCfgTable'

Router Interface Configuration Table.

rtrIfCfgEntry row .1.3.6.1.4.1.164.11.1.2.1

An entry in the Router Interface Configuration Table.

Indexes

No indexes recorded

Column Syntax OID

rtrIfCfgIndex

This object indicates the Router Interface Index.
(In some cases it will be equal to the Router Interface ifIndex).

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.1.2.1.1

rtrIfCfgIpAddress

IP Address of the Router Interface.

RFC1155-SMIIpAddress

Enumerated Values:

1	static
2	dynamic
3	pat
4	transparent

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.1.2.1.2

rtrIfCfgRowStatus

This object enables the user to
create/delete entries of this table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.11.1.2.1.3

rtrIfCfgIpMask

IP Mask Address Router Interface.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.1.2.1.4

rtrIfCfgIfIndex

ifIndex of the device interface connected
to this Router Interface.

SNMPv2-SMIInteger32r/w

Constraints:
range: 1-30

.1.3.6.1.4.1.164.11.1.2.1.5

rtrIfCfgType

The Router Interface Type.
atm - ATM router interface
lis - Logical IP Subnet router interface.
ethernet - Ethernet router interface.

Enumerationr/w

.1.3.6.1.4.1.164.11.1.2.1.6

rtrIfCfgVlanId

The VLAN ID assigned to Tagged frames transmitted
from this Router Interface.
The value inserted should be a defined VLAN.

Q-BRIDGE-MIBVlanIndexr/w

.1.3.6.1.4.1.164.11.1.2.1.7

rtrIfCfgMtu

The size of the largest packet which can be sent/received
on the interface, specified in octets. For interfaces that
are used for transmitting network datagrams, this is the
size of the largest network datagram that ca…

SNMPv2-SMIInteger32r/w

Constraints:
range: 0-65535

.1.3.6.1.4.1.164.11.1.2.1.8

rtrIfCfgName

The Router Interface Name.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Constraints:
range: 0-65535

.1.3.6.1.4.1.164.11.1.2.1.9

rtrIfCfgConnectionPointer

This parameter represents the entity that is connected
to this Router Interface.

The value of this parameter is a pointer to an existing row of a table,
where the entity connected to this Router Int…

SNMPv2-TCRowPointerr/w

Description:

.1.3.6.1.4.1.164.11.1.2.1.10

rtrIfCfgVlanTagging

The VLAN Tagging.

Enumerationr/w

.1.3.6.1.4.1.164.11.1.2.1.11

rtrIfCfgVlanPriority

The VLAN Priority.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.11.1.2.1.12

rtrIfCfgParams

This object represents one or more parameters of the Router Interface.
Each group of bits (one or more bits) represents a specific parameter
and its possible values.
This object's mapping and interpretation will be spec…

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.11.1.2.1.13

rtrIfCfgMngAccess

This object represents whether Management Access is enabled
via this Router Interface.

Enumerationr/w

Enumerated Values:

1	tx
2	rx

.1.3.6.1.4.1.164.11.1.2.1.14

rtrIfCfgLlcSnapEncaps

This object represents the LLC/SNAP Encapsulation.

Enumerationr/w

.1.3.6.1.4.1.164.11.1.2.1.15

rtrIfCfgDhcp

This object indicates whether DHCP is enabled for this Router Interface.

Enumerationr/w

Enumerated Values:

1	none
2	eraseIP
3	eraseDECnet
4	eraseIPX
5	eraseBrg
6	replaceIP
8	replaceIPX
9	replaceBrg
10	backupIP
12	backupIPX
13	backupBrg

.1.3.6.1.4.1.164.11.1.2.1.16

rtrIpAddrTable

table

.1.3.6.1.4.1.164.11.2.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk rtrIpAddrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::rtrIpAddrTable'

This table is parralel to MIB II IpAddrTable, and is used to
add/delete entries to/from that table. In addition it contains
private objects.

rtrIpAddrEntry row .1.3.6.1.4.1.164.11.2.1.1

The addressing information for one of this
entity's IP addresses.

Indexes

No indexes recorded

Column Syntax OID

rtrIpAdEntAddr

The IP address to which this entry's addressing
information pertains.

RFC1155-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.2.1.1.1

rtrIpAdEntIfIndex

The index value which uniquely identifies the
interface to which this entry is applicable. The
interface identified by a particular value of this
index is the same interface as identified by the
same value of ifIndex.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.2.1.1.2

rtrIpAdEntNetMask

The subnet mask associated with the IP address of
this entry. The value of the mask is an IP
address with all the network bits set to 1 and all
the hosts bits set to 0.

RFC1155-SMIIpAddressr/w

Enumerated Values:

1	ip
2	ipx
3	dec
4	bridge

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.2.1.1.3

rtrIpAdEntForwardIpBroadcast

This variable controls forwarding of IP (sub)net-directed
broadcasts destined for an attached sub(net).

Enumerationr/w

Enumerated Values:

1	tx
2	rx
3	cod

.1.3.6.1.4.1.164.11.2.1.1.4

rtrIpAdEntBackupAddr

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.2.1.1.5

rtrIpAdEntStatus

The Status variable is used to create and destroy a Ip Addresses.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.11.2.1.1.6

rtrIcmpRdTable

table

.1.3.6.1.4.1.164.11.2.2.2 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk rtrIcmpRdTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::rtrIcmpRdTable'

This table contains ICMP Router Discovery parameters
configurated per IP interface.

rtrIcmpRdEntry row .1.3.6.1.4.1.164.11.2.2.2.1

The ICMP parameters configurated for IP interface.

Indexes

No indexes recorded

Column Syntax OID

rtrIcmpRdIpAddr

The IP address to which this entry's information pertains.

RFC1155-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.2.2.2.1.1

rtrIcmpRdIpAdvertAddr

The IP destination address to be used for multicast
Router Advertisements sent from the interface. The
only permissible values are the all-systems multicast
address, 224.0.0.1, or the limited-broadcast address,
255.255.…

RFC1155-SMIIpAddressr/w

Enumerated Values:

1	block
2	forward
3	permit
4	deny
129	blockAndReport

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.2.2.2.1.2

rtrIcmpRdMaxAdvertInterval

The maximum time allowed between sending multicast
Router Advertisements from the interface, in seconds.
Must be no less than 4 seconds and no greater than 1800
seconds.

Integer32r/w

Enumerated Values:

1	none
2	l2multicast
3	arp
4	icmp
5	ip
6	udp
7	tcp
8	decnet
9	ipx

.1.3.6.1.4.1.164.11.2.2.2.1.3

rtrIcmpRdMinAdvertInterval

The minimum time allowed between sending unsolicited
multicast Router Advertisements from the interface, in
seconds. Must be no less than 3 seconds and no greater
than rtrIcmpRdMaxAdvertInterval.
Default: 0.75 * rtrIcm…

Integer32r/w

.1.3.6.1.4.1.164.11.2.2.2.1.4

rtrIcmpRdAdvertLifetime

The maximum length of time that the advertised addresses
are to be considered as valid. Must be no less than
rtrIcmpRdMaxAdvertInterval and no greater than 9000 seconds.
Default: 3 * rtrIcmpRdMaxAdvertInterval.

Integer32r/w

.1.3.6.1.4.1.164.11.2.2.2.1.5

rtrIcmpRdAdvertise

A flag indicating whether or not the address is to be
advertised.

Enumerationr/w

.1.3.6.1.4.1.164.11.2.2.2.1.6

rtrIcmpRdPreferenceLevel

The preferability of the address as a default router
address, relative to other router addresses on the same
subnet.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	valid
2	createRequest
3	underCreation
4	invalid

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.2.2.2.1.7

rtrIcmpRdEntStatus

Setting of any value to this object set values of
all fields to the default values.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.2.2.2.1.8

rtrRip2IfConfTable

table

.1.3.6.1.4.1.164.11.2.3.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk rtrRip2IfConfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::rtrRip2IfConfTable'

This table is an extension of rip2IfConfTable (RFC 1724 ,RIP 2).
It means that every time somebody creates/destroys a row in the
rip2IfConfTable, the same row should be automatically created/destroyed  
in this table.

rtrRip2IfConfEntry row .1.3.6.1.4.1.164.11.2.3.1.1

An entry in table rtrRip2IfConfTable.

Indexes

No indexes recorded

Column	Syntax	OID
rtrRip2IfConfAddress The IP Address of this system on the indicated subnet. For unnumbered interfaces, the value 0.0.0.N, where the least significant 24 bits (N) is the ifIndex for the IP Interface in network byte order	RFC1155-SMIIpAddress Type Constraints: `range: 4`	`.1.3.6.1.4.1.164.11.2.3.1.1.1`
rtrRip2IfConfVirtualDisdeprecated This variable defines the virtual number of hops assigned to the interface specified by rtrIfIpAddrIndex. This enables fine-tuning of the RIP routing algorithm.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.11.2.3.1.1.2`
rtrRip2IfConfAutoSenddeprecated When set to enable only the default route is sent through the interface. When set to disable, regular RIPs are sent.	Enumerationr/w	`.1.3.6.1.4.1.164.11.2.3.1.1.3`
rtrRip2IfConfRipEnable This object shows whether RIP Protocol is enabled on the current interface.	Enumerationr/w	`.1.3.6.1.4.1.164.11.2.3.1.1.4`

rtrNatIfConfTable

table

.1.3.6.1.4.1.164.11.2.5.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk rtrNatIfConfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::rtrNatIfConfTable'

A list of interfaces which require separate NAT configuration.

rtrNatIfConfEntry row .1.3.6.1.4.1.164.11.2.5.1.1

A single routing domain in a single subnet.

Indexes

No indexes recorded

Column Syntax OID

rtrNatIfVirtualAddress

The IP Address of the virtual subnet to be translated by the 'NAT box'
attached to this interface.
For some devices/cases, it might represent the Virtual Lowest IP Address.

RFC1155-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.2.5.1.1.1

rtrNatIfVirtualMask

The subnet Mask of the virtual subnet.
For some devices/cases, it might represent the Virtual Highest IP Address.

RFC1155-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.2.5.1.1.2

rtrNatIfConfStatus

Writing 'destroy' has the effect of deleting this interface.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.11.2.5.1.1.3

rtrNatIfRealAddress

The IP Address of the real subnet which is used by 'NAT box' for translation.
For some devices/cases, it might represent the Real Lowest IP Address.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.2.5.1.1.4

rtrNatIfRealMask

The subnet Mask of the real subnet.
For some devices/cases, it might represent the Real Highest IP Address.

RFC1155-SMIIpAddressr/w

Enumerated Values:

1	all
2	lan1
3	lan2
4	anyLan
5	wan

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.2.5.1.1.5

rtrNatIfType

NAT type.

static - Translate a specific virtual IP network to a specific real IP
network. TCP, UDP and ICMP sessions originated both in real and
virtual networks will be translated.
d…

Enumerationr/w

.1.3.6.1.4.1.164.11.2.5.1.1.6

rtrPatTable

table

.1.3.6.1.4.1.164.11.2.5.2 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk rtrPatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::rtrPatTable'

Port Address Translation (PAT -  single IP NAT) configuration Table.

rtrPatEntry row .1.3.6.1.4.1.164.11.2.5.2.1

Each entry describe unique mapping between real IP address,
range of ports and protocol, to local (virtual) IP address.
Ports are used in the TCP (rfc793) to name the ends of logical
connections which carry long term c…

Indexes

No indexes recorded

Column Syntax OID

rtrPatIdx

Running index for PAT table.

Integer32

.1.3.6.1.4.1.164.11.2.5.2.1.1

rtrPatRealAddress

The real IP Address used for translation

RFC1155-SMIIpAddressr/w

Constraints:
range: 1-50

.1.3.6.1.4.1.164.11.2.5.2.1.2

rtrPatVirtualAddress

The virtual IP Address used for translation

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.2.5.2.1.3

rtrPatLowestPort

Lowest Port number for this PAT entry

Integer32r/w

.1.3.6.1.4.1.164.11.2.5.2.1.4

rtrPatHighestPort

Highest Port number for this PAT entry

Integer32r/w

.1.3.6.1.4.1.164.11.2.5.2.1.5

rtrPatProtocol

Protocol selected.
This Protocol and port range (lowest port - highest port)
define the application (FTP, Telnet, SMTP etc.).
Protocol enumaration numbers correspond to IP header 'protocol' field
(e.g. 6 means TCP, 17 …

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.2.5.2.1.6

rtrPatStatus

This object enables creating and deleting
entries of the table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.11.2.5.2.1.7

rtrFACSActTable

table

.1.3.6.1.4.1.164.11.5.2 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk rtrFACSActTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::rtrFACSActTable'

The table of  FACS action.

rtrFACSActEntry row .1.3.6.1.4.1.164.11.5.2.1

Each rtrFACSActEntry consist of the following parameters

Indexes

No indexes recorded

Column Syntax OID

rtrFACSActType

This parameter indicates on which FACS Table the FACS
action will preform.

Enumeration

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.11.5.2.1.1

rtrFACSActIfIndex

The interface to which this FACS entry is applicable.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.5.2.1.2

rtrFACSAction

The management station that sends a SET request for one of these actions
with indexes rtrFACSType and rtrFACSIfIndex defines the type and the
interface Id for which all FACS statements are to be erased.
If no interfa…

Enumerationr/w

.1.3.6.1.4.1.164.11.5.2.1.3

rtrFACSActiveDB

This parameter will point on which Facs DataBase the SNMP agent
read. The Active dataBase is Read Only. The user may change FACS
statements in the temporary DataBase and then write it to the
Active DB.

Enumerationr/w

Enumerated Values:

2	disable
3	enable

.1.3.6.1.4.1.164.11.5.2.1.4

rtrFACSTable

table

.1.3.6.1.4.1.164.11.5.3 · 1 row entry · 14 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk rtrFACSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::rtrFACSTable'

The table of  FACS statment.

rtrFACSEntry row .1.3.6.1.4.1.164.11.5.3.1

Each FACS statment consists of the following parameters

Indexes

No indexes recorded

Column Syntax OID

rtrFACSIfIndex

The interface to which this FACS entry is applicable.
For applications this variables is always 0.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.5.3.1.1

rtrFACSProtocolType

This parameter define the protocol the Security Access Control
is applicable.

Enumeration

.1.3.6.1.4.1.164.11.5.3.1.2

rtrFACSType

The Mode of in which this FACS statement operates.
For applications this variable is always rx(2).

Enumeration

Enumerated Values:

2	disable
3	enable

.1.3.6.1.4.1.164.11.5.3.1.3

rtrFACSIndex

Index to the FACS Table.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.5.3.1.4

rtrFACSSrcAdd

The size of the octet string will be according to the protocol type
defined in rtrFACSProtocolType.

OctetStringr/w

.1.3.6.1.4.1.164.11.5.3.1.5

rtrFACSSrcAddMask

Source-address mask .

OctetStringr/w

.1.3.6.1.4.1.164.11.5.3.1.6

rtrFACSDesAdd

Destination-address The size of the octet string will be according to the
protocol type define in rtrFACSProtocolType .

OctetStringr/w

.1.3.6.1.4.1.164.11.5.3.1.7

rtrFACSDesAddMask

Destination-address mask .

OctetStringr/w

.1.3.6.1.4.1.164.11.5.3.1.8

rtrFACSOperation

... .

Enumerationr/w

.1.3.6.1.4.1.164.11.5.3.1.9

rtrFACSNetFiltering

... .

Enumerationr/w

.1.3.6.1.4.1.164.11.5.3.1.10

rtrFACSSocketNum

Port/socket number for different applications
0 is default meaning not applicable.
none(1),
ftp(21),
telnet(23),
smtp(25),
tftp(69),
snmp(161),
snmpTrap(162),
rip(520),
sapIPX(1106),
ripIPX(1107)

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.5.3.1.11

rtrFACSMask1Id

Index into RND mask table FACS/COD Type) .

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.5.3.1.12

rtrFACSMask2Id

Index into RND mask table FACS/COD according to
the value of rtrFACSType .

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.5.3.1.13

rtrFACSStatus

The status of a table entry.

Enumerationr/w

Enumerated Values:

2	down
3	up

.1.3.6.1.4.1.164.11.5.3.1.14

rtrBridgePortConfigTable

table

.1.3.6.1.4.1.164.11.7.1 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk rtrBridgePortConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::rtrBridgePortConfigTable'

Table of the bridge ports

rtrBridgePortConfigEntry row .1.3.6.1.4.1.164.11.7.1.1

Each entry defines a bridge port

Indexes

No indexes recorded

Column Syntax OID

rtrBridgePortCIndex

This is the index of the bridge port. It is the same
as 'dot1dBasePort' of the Bridge MIB.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.7.1.1.1

rtrBridgePortCIf

The config ifIndex the bridge port is sitting on.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.7.1.1.2

rtrBridgePortCStatus

The status of the RtrBridgePortConfigEntry.
Creating and destroying the bridge port is done by this
variable.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.11.7.1.1.3

wrDhcpTable

table

.1.3.6.1.4.1.164.11.7.2.2.1.2 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk wrDhcpTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::wrDhcpTable'

A list of DHCP entries. The number of entries is up to
DHCP current entries, according to the WEBRANger model.

wrDhcpEntry row .1.3.6.1.4.1.164.11.7.2.2.1.2.1

DHCP parameters per entry of the DHCP table.

Indexes

No indexes recorded

Column Syntax OID

wrDhcpLowIpAddress

DHCP Low Ip Address.

RFC1155-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.7.2.2.1.2.1.1

wrDhcpHighIpAddress

DHCP High Ip Address.

RFC1155-SMIIpAddressr/w

Enumerated Values:

2	off
3	renew
4	release

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.7.2.2.1.2.1.2

wrDhcpIpMaskAddress

IP mask Address.

RFC1155-SMIIpAddressr/w

Enumerated Values:

0	vendorClassId
1	ipAddrLeaseTime
2	serverId
3	clientId
4	hostName
5	dns
6	tftpServerName
7	bootFileName

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.7.2.2.1.2.1.3

wrDhcpDefaultGateway

Default Gateway's IP Address.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.7.2.2.1.2.1.4

wrDhcpPrimaryDNS

Primary DNS.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.7.2.2.1.2.1.5

wrDhcpSecondaryDNS

Secondary DNS.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.7.2.2.1.2.1.6

wrDhcpInterface

The IP addresse allocation is done according to the
interface type from which the DHCP request arrives.

Enumerationr/w

.1.3.6.1.4.1.164.11.7.2.2.1.2.1.7

wrDhcpRowStatus

This attribute allows to create/delete a row in this table.
For creating a row, the NMS should set
wrDhcpRowStatus.id = active(1).
For destroying a row, the NMS should set:
wrDhcpStatus.id = destroy(6).
Only rows with …

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.11.7.2.2.1.2.1.8

wrDhcpIpAddressLeaseTime

Allocated IP Address lease time in seconds.
A zero value specifies no time limitation.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.7.2.2.1.2.1.9

wrDhcpPoolName

DHCP pool name - string with max length of 10 characters

OctetStringr/w

.1.3.6.1.4.1.164.11.7.2.2.1.2.1.10

wrDhcpTftpServerIp

DHCP pool - TFTP-server IP Address.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.7.2.2.1.2.1.11

wrDhcpConfigFileName

TFTP-name of the configuration File Name for DHCP pool.

OctetStringr/w

.1.3.6.1.4.1.164.11.7.2.2.1.2.1.12

dhcpPoolAllocTable

table

.1.3.6.1.4.1.164.11.7.2.2.1.3 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk dhcpPoolAllocTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::dhcpPoolAllocTable'

A list of  DHCP  Pool Allocation entries.
Each entry (row) consist of a single IP Address belonging to DHCP pool 
whose lowest IP address is dhcpPoolAllocLowIpAddress. 
This IP address may be offered for leasing, or may already be 
leased (in use) by Host it's MacAddress is dhcpPoolAllocMacAddress.
Time left for leasing period is indicated by dhcpPoolAllocTimeLeft.
All posible statuses of IP address are indicated and controlled
by dhcpPoolAllocFlags

dhcpPoolAllocEntry row .1.3.6.1.4.1.164.11.7.2.2.1.3.1

DHCP Pool Allocation parameters per entry of the DHCP Pool Allocation table.

Indexes

wrLanifIndex wrLanIpxFrameType

Column Syntax OID

dhcpPoolAllocLowIpAddress

Lowest IP address of this pool, value eqaul to wrDhcpLowIpAddress for
the pool.

RFC1155-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.7.2.2.1.3.1.1

dhcpPoolAllocLeasingIpAddress

Single IP Address belonging to dhcp pool whose Lowest Ip Address is
dhcpPoolAllocLowIpAddress. This IP address may be offered for leasing
or may be leased by Host its MacAddress is dhcpPoolAllocMacAddress.
All posible …

RFC1155-SMIIpAddress

Enumerated Values:

1	t8023
2	ethernet
3	t8022
4	snap

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.7.2.2.1.3.1.2

dhcpPoolAllocMacAddress

MAC Address to which the IP address has been leased

MacAddress

Type Constraints:
range: 6

.1.3.6.1.4.1.164.11.7.2.2.1.3.1.3

dhcpPoolAllocTimeLeft

IP address leasing time left in seconds

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.7.2.2.1.3.1.4

dhcpPoolAllocFlags

These flags indicates status of each IP address.
User may change value to free, via dhcpPoolAllocFreeCmd

Enumeration

.1.3.6.1.4.1.164.11.7.2.2.1.3.1.5

dhcpPoolAllocFreeCmd

Setting this attribute to On (3), will enforce the agent to
Free this entry.
The Agent will change the value of this MIB object to off(2)
automatically, after performing the command.
Setting this object to off(2), wil…

Enumerationr/w

.1.3.6.1.4.1.164.11.7.2.2.1.3.1.6

dhcpRelayTable

table

.1.3.6.1.4.1.164.11.7.2.2.1.4 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk dhcpRelayTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::dhcpRelayTable'

A list of DHCP relay entries.

dhcpRelayEntry row .1.3.6.1.4.1.164.11.7.2.2.1.4.1

DHCP Relay parameters per entry of the DHCP relay table.

Indexes

No indexes recorded

Column	Syntax	OID
dhcpRelayAction Setting this attribute to enable (3), will enable DHCP Relay action for this interface (Only if DHCP Server is disabled for device - wrDhcpAction=disable). dhcpRelayServerIpAddressaddress should not be 0.0.0.0 when e…	Enumerationr/w	`.1.3.6.1.4.1.164.11.7.2.2.1.4.1.1`
dhcpRelayServerIpAddress DHCP Server IP Address.	RFC1155-SMIIpAddressr/w Type Constraints: `range: 4`	`.1.3.6.1.4.1.164.11.7.2.2.1.4.1.2`
dhcpRelayMaxHop Maximum number of hops till DHCP Server. upper limit is 16 hops	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.11.7.2.2.1.4.1.3`

dhcpClientTable

table

.1.3.6.1.4.1.164.11.7.2.2.1.6 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk dhcpClientTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::dhcpClientTable'

A list of DHCP client entries.

dhcpClientEntry row .1.3.6.1.4.1.164.11.7.2.2.1.6.1

DHCP Client parameters per entry of the DHCP Client table.

Indexes

No indexes recorded

Column	Syntax	OID
dhcpClientAction This parameter default value is enable(3). Setting this attribute to disable (2), will disable DHCP Client action for this interface. This parameter can be changed to disable (2) only (it cannot be changed from disab…	Enumerationr/w	`.1.3.6.1.4.1.164.11.7.2.2.1.6.1.1`
dhcpClientServerIpAddress DHCP Server IP Address.	RFC1155-SMIIpAddressr/w Type Constraints: `range: 4`	`.1.3.6.1.4.1.164.11.7.2.2.1.6.1.2`
dhcpClientLeaseExpirationTime This parameter holds the time (in minutes) left until lease expiration.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.11.7.2.2.1.6.1.3`
dhcpClientStatus This parametr displays the DHCP status.	SNMPv2-TCDisplayString Type Constraints: `range: 0..255` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.164.11.7.2.2.1.6.1.4`

dhcpIfClientTable

table

.1.3.6.1.4.1.164.11.7.2.2.1.7 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk dhcpIfClientTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::dhcpIfClientTable'

DHCP client entries for each Interface.

dhcpIfClientEntry row .1.3.6.1.4.1.164.11.7.2.2.1.7.1

DHCP Clients per entry of the DHCP Interface Client table.

Indexes

No indexes recorded

Column Syntax OID

dhcpIfClientIpAddress

DHCP Client IP Address.

RFC1155-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.7.2.2.1.7.1.2

dhcpIfClientRowStatus

The row status used for creating, modifying, and deleting instances
of the columnar objects in the dhcpIfClientTable.

For Vmux Devices, it will be possible only to Delete instances.
The addition of Clien…

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.11.7.2.2.1.7.1.3

dhcpClientNTable

table

.1.3.6.1.4.1.164.11.7.2.2.1.9 · 1 row entry · 21 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk dhcpClientNTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::dhcpClientNTable'

The DHCP Client table (New).

dhcpClientNEntry row .1.3.6.1.4.1.164.11.7.2.2.1.9.1

An entry of this table.

Indexes

No indexes recorded

Column Syntax OID

dhcpClientIndex

The DHCP Client index.
Index can be ifIndex and/or index of a router interface or host.

SNMPv2-SMIUnsigned32

Enumerated Values:

1	unknown
2	bridge
3	ipRouter
4	ipxRouter
5	ipAndIpxRouter
6	bRouter
7	ipBrouter
8	ipxBrouter
9	ipAndIpxBrouter
10	bridgeAndStp

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.1

dhcpClientAdminStatus

The Administrative Status of DHCP client.

Enumerationr/w

Enumerated Values:

2	disable
3	enable
4	redundancy

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.2

dhcpClientOperStatus

The Operational Status of DHCP client.

Enumeration

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.3

dhcpClientAddressType

The Address Type of all InetAddress objects.

INET-ADDRESS-MIBInetAddressTyper/w

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.4

dhcpClientAddress

The DHCP Client Address, which is assigned by the DHCP server.

INET-ADDRESS-MIBInetAddress

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.5

dhcpClientAddressMask

The DHCP Client Address Mask, which is assigned by the DHCP server.

INET-ADDRESS-MIBInetAddress

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.6

dhcpClientNextHop

The Next Hop (Default Gateway) of the DHCP client.

INET-ADDRESS-MIBInetAddress

Enumerated Values:

1	notApplicable
2	manual
3	program

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.7

dhcpClientServerAddress

The DHCP Server Address.
Although object is defined as read-write, current support is read-only.

INET-ADDRESS-MIBInetAddressr/w

Enumerated Values:

1	notApplicable
2	r16
3	r32
4	r48
5	r64
6	r96
7	r128
8	r256
9	r768

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.8

dhcpClientActualLeaseTime

The Actual Lease Time (for Address received from the server),
measured in seconds.
Value=FFFFFFFF represents an infinite actual lease time.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.9

dhcpClientRemainLeaseTime

The Remaining Lease Time (for Address received from the server),
measured in seconds.
Value=FFFFFFFF represents an infinite remaining lease time.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.10

dhcpClientCommand

The possible commands of DHCP client to DHCP server.
Upon performing a command, value should be automatically returned to off(2).

Enumerationr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.11

dhcpClientOpAdminStatus

The Administrative Status of the different options.
Bit=1 means that respective option is enabled/activated.

Bitsr/w

Enumerated Values:

2	disable
3	enable

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.12

dhcpClientOpVendorClassId

The Vendor Class Identifier.
Identifier should include at least 1 character.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.13

dhcpClientOpIpAddrLeaseTime

The IP Address Lease Time, measured in seconds.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.14

dhcpClientOpServerId

The Server Identifier (reported IP Address).

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.15

dhcpClientOpClientIdType

The Client Identifier Type.

Type=0 indicates that Client Identifier is a string,
which is set by dhcpClientOpClientId.

Type=1 indicates that Client Identifier represents
the Ethernet Hardwa…

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.16

dhcpClientOpClientId

The Client Identifier.
Identifier should include at least 1 character.

When Type=1 (dhcpClientOpClientIdType),
it means that current object is read-only
as it represents the Ethernet Hardware Address (MAC…

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.17

dhcpClientOpHostName

The Host Name.
Name should include at least 1 character.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.18

dhcpClientOpDns

The Domain Name Server (DNS),
which is a list of servers available to the client.
This object should include at least 4 octets
and must always be a multiple of 4 octets.

OctetString

Enumerated Values:

1	no
2	yes

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.19

dhcpClientOpTftpServerName

The TFTP Server Name.
Name should include at least 1 character.

SNMP-FRAMEWORK-MIBSnmpAdminString

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.20

dhcpClientOpBootFileName

The Boot File Name.
Name should include at least 1 character.

SNMP-FRAMEWORK-MIBSnmpAdminString

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.11.7.2.2.1.9.1.21

wrLanIpxNetTable

table

.1.3.6.1.4.1.164.11.7.2.3.2 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk wrLanIpxNetTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::wrLanIpxNetTable'

Lan IPX nets Table.

wrLanIpxNetEntry row .1.3.6.1.4.1.164.11.7.2.3.2.1

IPX Nets per frame type & LAN port. The table entries
will be created by the agent

Indexes

No indexes recorded

Column Syntax OID

wrLanifIndex

LAN port ifIndex.

SNMPv2-SMIInteger32

Enumerated Values:

1	bridge
2	router
3	brouter
4	off

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.7.2.3.2.1.1

wrLanIpxFrameType

Frame Type

Enumeration

.1.3.6.1.4.1.164.11.7.2.3.2.1.2

wrIpxNetAddress

Net address per Frame Type & LAN port.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.7.2.3.2.1.3

ripSapIfConfTable

table

.1.3.6.1.4.1.164.11.7.2.3.4 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk ripSapIfConfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::ripSapIfConfTable'

A list of Interfaces which require separate
configuration in RIP/SAP.

ripSapIfConfEntry row .1.3.6.1.4.1.164.11.7.2.3.4.1

A Single Routing Domain in a single Subnet.

Indexes

No indexes recorded

Column Syntax OID

ripSapIfConfIfIndex

The interface ifIndex.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.7.2.3.4.1.1

ripSapIfConfMode

The ifIndex RIP/SAP mode.

Enumerationr/w

.1.3.6.1.4.1.164.11.7.2.3.4.1.2

ripSapIfConfStatus

This attribute allows to create/delete a row in this table.
For creating a row, the NMS should set
ripSapIfConfStatus.id1 = active(1).
For destroying a row, the NMS should set:
ripSapIfConfStatus.id1 = destroy(6).
Only…

SNMPv2-TCRowStatusr/w

Enumerated Values:

1	disable
2	enable

Description:

.1.3.6.1.4.1.164.11.7.2.3.4.1.3

wrIpAddressTable

table

.1.3.6.1.4.1.164.11.7.2.4.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk wrIpAddressTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::wrIpAddressTable'

Link IP addresses Table.

wrIpAddressEntry row .1.3.6.1.4.1.164.11.7.2.4.1.1

Ip Address per Link

Indexes

No indexes recorded

Column Syntax OID

wrIpIfIndex

Port interface index.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.7.2.4.1.1.1

wrIpAddress

Link IP Address.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.7.2.4.1.1.2

wrIpMask

Link IP mask Address.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.7.2.4.1.1.3

wrIpRowStatus

This attribute allows to create/delete a row in this table.
For creating a row, the NMS should set
wrIpRowStatus.id1 = active(1).
For destroying a row, the NMS should set:
wrIpRowStatus.id1 = destroy(6).
Only rows with…

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.11.7.2.4.1.1.4

wrSpoofingTable

table

.1.3.6.1.4.1.164.11.7.2.4.2 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk wrSpoofingTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::wrSpoofingTable'

Spoofing Table.

wrSpoofingEntry row .1.3.6.1.4.1.164.11.7.2.4.2.1

Spoofing per Link

Indexes

No indexes recorded

Column Syntax OID

wrSpoofingIfIndex

Port interface index.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.7.2.4.2.1.1

wrSpoofingAction

Spoofing action is applied by bit code:
enable : bit 0 set (disable: bit 0 is 0)
keepAlive : bit 1
... : bit 2
and so on.
For the above example, to set spoofing to keepAlive action,
the object's …

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.7.2.4.2.1.2

wrSpoofingAgingStation

Aging time of stations list, in min. The agent 'translates'
the time entered in minutes, to 10 min. resolution, as
follows:
1..10 min - 10 min
11..20 min - 20 min
and so on...
0 is not a valid valu…

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.7.2.4.2.1.3

wrSpoofingRowStatus

This attribute allows to create/delete a row in this table.
For creating a row, the NMS should set
wrSpoofingRowStatus.id1 = active(1).
For destroying a row, the NMS should set:
wrSpoofingRowStatus.id1 = destroy(6).
On…

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.11.7.2.4.2.1.4

wrLanIfTable

table

.1.3.6.1.4.1.164.11.7.2.4.3 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk wrLanIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::wrLanIfTable'

Link IP addresses Table.

wrLanIfEntry row .1.3.6.1.4.1.164.11.7.2.4.3.1

Ip Address per Link

Indexes

No indexes recorded

Column	Syntax	OID
wrLanIfIndex Port interface index.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.11.7.2.4.3.1.1`
wrLanBridgeRouterMode This parameter indicates whether the link is Bridge or Router and specifies the Router's type.	Enumerationr/w	`.1.3.6.1.4.1.164.11.7.2.4.3.1.2`
wrLanIfState The LAN is disabled or enabled. For LAN 2 it can be also 'redundancy'.	Enumerationr/w	`.1.3.6.1.4.1.164.11.7.2.4.3.1.3`
wrLanIfRdnTimeout LAN Redundancy Timeout in seconds. Applicable when wrLanIfState=redundancy.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.11.7.2.4.3.1.4`

wrSyncCnfgTable

table

.1.3.6.1.4.1.164.11.7.2.4.4 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk wrSyncCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::wrSyncCnfgTable'

Configuration table for Async interface.

wrSyncCnfgEntry row .1.3.6.1.4.1.164.11.7.2.4.4.1

Configuration table

Indexes

No indexes recorded

Column	Syntax	OID
wrSyncIfIndex Sync interface index.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.11.7.2.4.4.1.1`
wrSyncClkMode Clock Mode.	Enumerationr/w	`.1.3.6.1.4.1.164.11.7.2.4.4.1.2`
wrSyncClkRate Clock Rate in. Rate can be changed if Clock Mode is Program only.	Enumerationr/w	`.1.3.6.1.4.1.164.11.7.2.4.4.1.3`

wrFrCnfgTable

table

.1.3.6.1.4.1.164.11.7.2.4.5 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk wrFrCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::wrFrCnfgTable'

Configuration table for Fr parameters that do not exist in RFC2115.

wrFrCnfgEntry row .1.3.6.1.4.1.164.11.7.2.4.5.1

Configuration entry for Fr parameters that do not exist in RFC2115.

Indexes

No indexes recorded

Column	Syntax	OID
wrFrDlciLearningMode This parameter enables the webranger to learn the DLCi's configuration and maintanance protocol for the current interface. off - the WR will read the user's configuration for this interface. on - the WR will begin sel…	Enumerationr/w	`.1.3.6.1.4.1.164.11.7.2.4.5.1.1`
wrFrCllmMessages This parameter enables/disables the Webranger to Tx/Rx CLLM (Consolidated Link Layer Management) messages via DLCI 1023. The CLLM messages are link layer control messages. They can be used for example in cases of c…	Enumerationr/w	`.1.3.6.1.4.1.164.11.7.2.4.5.1.2`

rtrIfIpTable

table

.1.3.6.1.4.1.164.11.7.3.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk rtrIfIpTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::rtrIfIpTable'

Router interfaces table.

rtrIfIpEntry row .1.3.6.1.4.1.164.11.7.3.1.1

An entry in table rtrIfIpTable.

Indexes

No indexes recorded

Column Syntax OID

rtrIfIp

IP Address.

RFC1155-SMIIpAddress

Enumerated Values:

1	other
2	reject
3	local
4	remote

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.7.3.1.1.1

rtrIfRowStatus

SNMPv2-TCRowStatusr/w

Enumerated Values:

1	other
2	local
3	netmgmt
8	rip
41	lis

Description:

.1.3.6.1.4.1.164.11.7.3.1.1.2

rtrIfIpMask

IP mask Address.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.7.3.1.1.3

rtrIfIndex

The ifIndex connection, on which the IP is determined.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.7.3.1.1.4

rtrIfMng

An IP interface might be determined as a management
connection (under the product limitations).

Enumerationr/w

.1.3.6.1.4.1.164.11.7.3.1.1.5

rtrIfVlanId

The VLAN ID assigned to Tagged frames transmitted
from this port.
The value inserted should be a defined VLAN.

Q-BRIDGE-MIBVlanIndexr/w

.1.3.6.1.4.1.164.11.7.3.1.1.6

brtrIfTable

table

.1.3.6.1.4.1.164.11.7.3.2 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk brtrIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::brtrIfTable'

LAN interface table.

brtrIfEntry row .1.3.6.1.4.1.164.11.7.3.2.1

The entries of this table will be created by agent.

Indexes

No indexes recorded

Column Syntax OID

brtrIfIndex

The index of the interface (LAN or ATM).

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.7.3.2.1.1

brtrIfMode

Connection Mode.

Enumerationr/w

.1.3.6.1.4.1.164.11.7.3.2.1.2

brtrIfMaxFrameSize

Frame Max Size.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	no
3	yes

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.7.3.2.1.3

brtrLanIfTable

table

.1.3.6.1.4.1.164.11.7.3.4 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk brtrLanIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::brtrLanIfTable'

LAN interface table.

brtrLanIfEntry row .1.3.6.1.4.1.164.11.7.3.4.1

The entries of this table will be created by agent .

Indexes

No indexes recorded

Column Syntax OID

brtrLanIfIndex

The index of the LAN entity (physical interface).

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.7.3.4.1.1

brtrLanIpAddress

Host IP address. Applicable for bridge mode connection only.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.7.3.4.1.2

brtrLanIpMask

Host IP Mask. Applicable for bridge mode connection only.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.7.3.4.1.3

brtrLanMaxRateEnable

This parameter determines the HW ability of the LAN
card according to HW.

Enumeration

.1.3.6.1.4.1.164.11.7.3.4.1.4

brtrLanMaxRate

Max Rate.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.7.3.4.1.5

brtrLanMng

An IP interface might be determined as a management
connection (under the product limitations).

Enumerationr/w

Enumerated Values:

1	notApplicable
2	no
3	yes

.1.3.6.1.4.1.164.11.7.3.4.1.6

brtrLanDefaultRouter

Default Router's (Gateway's) IP Address.
For each LAN interface there may be a different Default Router.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.7.3.4.1.7

rtrIsdnIfTable

table

.1.3.6.1.4.1.164.11.7.3.5 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk rtrIsdnIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::rtrIsdnIfTable'

This table contains ISDN parameters that do not appear in the standard MIBs.

rtrIsdnIfEntry row .1.3.6.1.4.1.164.11.7.3.5.1

Entries for ISDN parameters that do not appear in the standard MIBs.

Indexes

No indexes recorded

Column	Syntax	OID
rtrIsdnIfMinNumBchans Minimum number of B channels that the ISDN Dialer of the router will use for Dialing out. This parameter will be used for the BOD (Bandwidth On Demand) feature. Dial up on B channels is according to the need of bandwidt…	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.11.7.3.5.1.1`
rtrIsdnIfMaxNumBchans Maximum number of B channels that the ISDN Dialer of the router will use for Dialing out. This parameter will be used for the BOD (Bandwidth On Demand) feature. Dial up on B channels is according to the need of bandwidt…	SNMPv2-SMIInteger32r/w Constraints: `range: 0-899`	`.1.3.6.1.4.1.164.11.7.3.5.1.2`

rtrLcrTable

table

.1.3.6.1.4.1.164.11.7.3.6 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk rtrLcrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::rtrLcrTable'

Least Cost Routing Table.
The user will be able to set a prefix for an outgoing number
that arrives with a predefined prefix in order to redirect
the number for the LCR process to be achieved.

rtrLcrEntry row .1.3.6.1.4.1.164.11.7.3.6.1

Least Cost Routing Entry.

Indexes

No indexes recorded

Column Syntax OID

rtrLcrOutIfIndex

The outgoing interface Number of the current route.
The incoming interface number is the value of ifIndex.

IF-MIBInterfaceIndex

Type Constraints:
range: 1..2147483647

Description:

.1.3.6.1.4.1.164.11.7.3.6.1.1

rtrLcrRowStatus

Row Status for adding/destroying rows.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.11.7.3.6.1.2

rtrLcrInPrefix

This prefix is part of the called number existing in the incoming packet.

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.11.7.3.6.1.3

rtrLcrOutPrefix

This prefix will be inserted into the outgoing packet.

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.11.7.3.6.1.4

rtrConfigTable

table

.1.3.6.1.4.1.164.11.9.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk rtrConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::rtrConfigTable'

The Router's Configuration table.

rtrConfigEntry row .1.3.6.1.4.1.164.11.9.1.1

An entry in the Router's Configuration table.

Indexes

No indexes recorded

Column	Syntax	OID
rtrConfigIndex This object indicates the Router's Index.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.11.9.1.1.1`
rtrConfigDefaultGateway Router Default Gateway.	RFC1155-SMIIpAddressr/w Type Constraints: `range: 4`	`.1.3.6.1.4.1.164.11.9.1.1.2`
rtrConfigArpAgingTime ARP Aging Time.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.11.9.1.1.3`
rtrConfigClassifierTosMask This object indicates the Classifier's TOS Mask, as follows: 0x1C for DTR -- rfc795 0x1E for Cisco 0xE0 for Precedence -- rfc795 0xFC for Diffserv Else for Manual .	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.11.9.1.1.5`
rtrConfigRIPMode This object determines the Router Information Protocol to measure the shortest path between 2 positions on the network.	Enumerationr/w	`.1.3.6.1.4.1.164.11.9.1.1.6`

rtrFwdTable

table

.1.3.6.1.4.1.164.11.9.3 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk rtrFwdTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::rtrFwdTable'

The Router's Forwarding Table.

rtrFwdEntry row .1.3.6.1.4.1.164.11.9.3.1

An entry in the Router's Forwarding table.

Indexes

No indexes recorded

Column Syntax OID

rtrFwdIdx

This object indicates the Router Index.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.9.3.1.1

rtrFwdIpAddress

This object indicates the Destination IP Address.

RFC1155-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.9.3.1.2

rtrFwdIpMask

This object indicates the Mask IP address.

RFC1155-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.9.3.1.3

rtrFwdRuleIdx

This object indicates the Rule's Number.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.9.3.1.4

rtrFwdRowStatus

This object enables the user to
create/delete entries in this table.

Entry of Type rtrFwdType = staticRouting(3)
are created by the user.
Only this type of entries can be deleted by the user.
…

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.11.9.3.1.5

rtrFwdNextHop

This object indicates the IP Address of the Next Hop.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.9.3.1.6

rtrFwdIfIndex

This object indicates the Interface Index.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.9.3.1.7

rtrFwdType

The type of route. Note that local(3) refers
to a route for which the next hop is the final
destination; remote(4) refers to a route for
which the next hop is not the final destina-
tion.

Routes …

Enumerationr/w

.1.3.6.1.4.1.164.11.9.3.1.8

rtrFwdProto

The routing mechanism via which this route was
learned. Inclusion of values for gateway routing
protocols is not intended to imply that
hosts should support those protocols.

Enumeration

.1.3.6.1.4.1.164.11.9.3.1.9

rtrFwdEthQueue

This object indicates the ETH Queue number.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.9.3.1.10

rtrFwdMetric1

The primary routing metric for this route.
The semantics of this metric are determined by
the routing-protocol specified in the route's
rtrFwdProto value. If this metric is not
used, its value should be set to -1.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.11.9.3.1.11

rtrPbrTable

table

.1.3.6.1.4.1.164.11.9.4 · 1 row entry · 15 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk rtrPbrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::rtrPbrTable'

The Router's Forwarding Table.

rtrPbrEntry row .1.3.6.1.4.1.164.11.9.4.1

An entry in the Router's Policy Based Routing (PBR) table.

Indexes

No indexes recorded

Column Syntax OID

rtrPbrIdx

This object indicates the Router Index.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.11.9.4.1.1

rtrPbrInterface

Router interface for which this match-set
rule applies.

IF-MIBInterfaceIndex

Type Constraints:
range: 1..2147483647

Description:

.1.3.6.1.4.1.164.11.9.4.1.2

rtrPbrRuleIdx

This object indicates the Policy Based Routing (PBR)
match-set rule index.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.11.9.4.1.3

rtrPbrRowStatus

This object enables the user to
create/delete entries of this table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.11.9.4.1.4

rtrPbrMatchAllFrames

Forwarding decision is made regardless PBR Rule
(as if all conditions are matched)

Enumerationr/w

.1.3.6.1.4.1.164.11.9.4.1.5

rtrPbrSourceIpAddress

Received frame source IP Address.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.9.4.1.6

rtrPbrSourceIpMask

The subnet mask of the source IP Address.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.9.4.1.7

rtrPbrDestIpAddress

Received frame destination IP Address.

RFC1155-SMIIpAddressr/w

Constraints:
range: 1-96

.1.3.6.1.4.1.164.11.9.4.1.8

rtrPbrDestIpMask

The subnet mask of the destination IP Address.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.9.4.1.9

rtrPbrIpProtocol

Value of Protocol field in IP Frame header.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.11.9.4.1.10

rtrPbrMinFrameLength

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.11.9.4.1.11

rtrPbrMaxFrameLength

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.11.9.4.1.12

rtrPbrDiscardFrame

Discard a frame when rule is matched .

Enumerationr/w

.1.3.6.1.4.1.164.11.9.4.1.13

rtrPbrForwardingInterface

The router Interface through which the frame
should be forwarded, when rule is matched.
If there's no forwarding interface,
then this object has a value of zero

IF-MIBInterfaceIndexOrZeror/w

Type Constraints:
range: 0..2147483647

Description:

.1.3.6.1.4.1.164.11.9.4.1.14

rtrPbrNextHop

IP Address of Next Hop, when Forwarding Interface is LAN,
or has BridgePDU (BVI) encapsulation.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.11.9.4.1.15

atmIfDataTable

table

.1.3.6.1.4.1.164.12.2.1.1.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmIfDataTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmIfDataTable'

The ATM interface Data table.

atmIfDataEntry row .1.3.6.1.4.1.164.12.2.1.1.1.1

An entry in the ATM interface Data table.

Indexes

IF-MIBifIndex atmVpCurrentVpi

Column	Syntax	OID
atmIfTimeElapsed The number of seconds that have elapsed since the beginning of the near end current error- measurement period.	Integer32	`.1.3.6.1.4.1.164.12.2.1.1.1.1.1`
atmIfValidIntervals The number of previous near end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complet…	Integer32	`.1.3.6.1.4.1.164.12.2.1.1.1.1.2`
atmIfTxCells The counter associated with the total number of transmitted cells, encountered by an ATM interface.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.1.1.1.3`
atmIfRxCells The counter associated with the total number of received cells, encountered by an ATM interface.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.1.1.1.4`
atmIfUncorrectedHecs The counter associated with the total number of cells with uncorrected HEC errors, encountered by an ATM interface.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.1.1.1.5`

atmIfCurrentTable

table

.1.3.6.1.4.1.164.12.2.1.1.2 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmIfCurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmIfCurrentTable'

The ATM interface Current table.

atmIfCurrentEntry row .1.3.6.1.4.1.164.12.2.1.1.2.1

An entry in the ATM interface Current table.

Indexes

No indexes recorded

Column	Syntax	OID
atmIfCurrentTxCells The counter associated with the number of transmitted cells, encountered by an ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.1.2.1.1`
atmIfCurrentRxCells The counter associated with the number of received cells, encountered by an ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.1.2.1.2`
atmIfCurrentCorrectedHecs The counter associated with the number of cells with corrected HEC errors, encountered by an ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.1.2.1.3`
atmIfCurrentUncorrectedHecs The counter associated with the number of cells with uncorrected HEC errors, encountered by an ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.1.2.1.4`
atmIfCurrentHecErrorSeconds The counter associated with the number of seconds with HEC errors, encountered by an ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.1.2.1.5`

atmIfIntervalTable

table

.1.3.6.1.4.1.164.12.2.1.1.3 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmIfIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmIfIntervalTable'

The ATM interface Interval table.

atmIfIntervalEntry row .1.3.6.1.4.1.164.12.2.1.1.3.1

An entry in the ATM interface Interval table.

Indexes

No indexes recorded

Column	Syntax	OID
atmIfIntervalNumber A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).	Integer32	`.1.3.6.1.4.1.164.12.2.1.1.3.1.1`
atmIfIntervalTxCells The counter associated with the number of transmitted cells , encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.1.3.1.2`
atmIfIntervalRxCells The counter associated with the number of received cells, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.1.3.1.3`
atmIfIntervalCorrectedHecs The counter associated with the number of cells with corrected HEC errors, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.1.3.1.4`
atmIfIntervalUncorrectedHecs The counter associated with the number of cells with uncorrected HEC errors, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.1.3.1.5`
atmIfIntervalHecErrorSeconds The counter associated with the number of seconds with HEC errors, encountered by an ATM interface in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.1.3.1.6`

aal5VccXTable

table

.1.3.6.1.4.1.164.12.2.1.1.4 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk aal5VccXTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::aal5VccXTable'

This table is an extension to AAL5 VCC Table.

aal5VccXEntry row .1.3.6.1.4.1.164.12.2.1.1.4.1

This list contains the additional AAL5 VCC
performance parameters and is indexed
by ifIndex values of AAL5 interfaces
and the associated VPI/VCI values.

Indexes

No indexes recorded

Column	Syntax	OID
aal5VccInFrames The number of frames received via this interface.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.1.4.1.1`
aal5VccOutFrames The total number of frames transmitted out of the interface.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.1.4.1.2`
aal5VccUnknownProtocolFrames The number of frames that were discarded due to unsupported protocol encapsulation on this VCC.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.1.4.1.3`

aal5VccCurrentTable

table

.1.3.6.1.4.1.164.12.2.1.1.5 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk aal5VccCurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::aal5VccCurrentTable'

The AAL5 Current table.

aal5VccCurrentEntry row .1.3.6.1.4.1.164.12.2.1.1.5.1

An entry in the AAL5 Current table.

Indexes

No indexes recorded

Column Syntax OID

aal5VccCurrentInFrames

The counter associated with the number of received frames,
encountered by the AAL5 interface in the current 15 minute
interval.

SNMPv2-SMIGauge32

Enumerated Values:

2	forward
3	backward

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.1.5.1.1

aal5VccCurrentOutFrames

The counter associated with the number of transmitted frames,
encountered by the AAL5 interface in the current 15 minute
interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.1.5.1.2

aal5VccCurrentUnknownProtocolFrames

The counter associated with the number of frames that were
discarded due to unsupported protocol encapsulation,
encountered by the AAL5 interface in the current 15 minute
interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.1.5.1.3

aal5VccCurrentCrcErrors

The counter associated with the number of AAL5 CPCS PDUs
received with CRC-32 errors, encountered by the AAL5
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.1.5.1.4

aal5VccCurrentLengthError

The counter associated with the number of received frames
with length error, encountered by the AAL5 interface in the
current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.1.5.1.5

aal5VccCurrentInputCongestionDropped

The counter associated with the number of
dropped frames due to congestion, encountered by
the AAL5 interface on the Receive direction
in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.1.5.1.6

aal5VccCurrentOutputCongestionDropped

The counter associated with the number of
dropped frames due to congestion, encountered by
the AAL5 interface on the Transmit direction
in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.1.5.1.7

aal5VccIntervalTable

table

.1.3.6.1.4.1.164.12.2.1.1.6 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk aal5VccIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::aal5VccIntervalTable'

The AAL5 Interval table.

aal5VccIntervalEntry row .1.3.6.1.4.1.164.12.2.1.1.6.1

An entry in the AAL5 Interval table.

Indexes

No indexes recorded

Column Syntax OID

aal5VccIntervalNumber

A number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals exist).

Integer32

.1.3.6.1.4.1.164.12.2.1.1.6.1.1

aal5VccIntervalInFrames

The counter associated with the number of received frames,
encountered by the AAL5 interface in one of the previous
96, individual 15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.1.6.1.2

aal5VccIntervalOutFrames

The counter associated with the number of transmitted frames,
encountered by the AAL5 interface in in one of the previous
96, individual 15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.1.6.1.3

aal5VccIntervalUnknownProtocolFrames

The counter associated with the number of frames that were
discarded due to unsupported protocol encapsulation,
encountered by the AAL5 interface in one of the previous
96, individual 15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.1.6.1.4

aal5VccIntervalCrcErrors

The counter associated with the number of AAL5 CPCS PDUs
received with CRC-32 errors, encountered by the AAL5
interface in one of the previous 96, individual 15 minute,
intervals.

SNMPv2-SMIGauge32

Enumerated Values:

2	normal
3	unacceptable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.1.6.1.5

aal5VccIntervalLengthError

The counter associated with the number of received frames
with length error, encountered by the AAL5 interface in one
of the previous 96, individual 15 minute, intervals.

SNMPv2-SMIGauge32

Enumerated Values:

2	normal
4	degraded

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.1.6.1.6

aal5VccIntervalInputCongestionDropped

The counter associated with the number of dropped frames
due to a congestion, encountered by the AAL5 interface on
the Receive direction in one of the previous 96, individual
15 minute, intervals

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.1.6.1.7

aal5VccIntervalOutputCongestionDropped

The counter associated with the number of dropped frames
due to a congestion, encountered by the AAL5 interface on
the Transmit direction in one of the previous 96, individual
15 minute, intervals

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.1.6.1.8

atmVpCurrentTable

table

.1.3.6.1.4.1.164.12.2.1.2.1.1 · 1 row entry · 24 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmVpCurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmVpCurrentTable'

The ATM VP Current table.

atmVpCurrentEntry row .1.3.6.1.4.1.164.12.2.1.2.1.1.1

An entry in the ATM VP Current table.

Indexes

No indexes recorded

Column	Syntax	OID
atmVpCurrentVpi The VPI of the VPL.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.1`
atmVpCurrentRxCellsClp01 The counter associated with the number of transmitted cells, encountered by the VPL of this ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.2`
atmVpCurrentRxCellsClp0 The counter associated with the number of received cells, encountered by the VPL of this ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.3`
atmVpCurrentGcra0Violations The counter associated with the number of cells violating GCRA0, encountered by the VPL of this ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.4`
atmVpCurrentGcra1Violations The counter associated with the number of cells violating GCRA1, encountered by the VPL of this ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.5`
atmVpCurrentRxAIS The counter associated with the number of received AIS cells, encountered by the VPL of this ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.6`
atmVpCurrentTxAIS The counter associated with the number of transmitted AIS cells, encountered by the VPL of this ATM interface in the current 15 minute interval. Not Supported in the first phase.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.7`
atmVpCurrentRxRDI The counter associated with the number of received RDI cells, encountered by the VPL of this ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.8`
atmVpCurrentTxRDI The counter associated with the number of transmitted RDI cells, encountered by the VPL of this ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.9`
atmVpCurrentContinuityLoss The counter associated with the number of loss of continuity cells, encountered by the VPL of this ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.10`
atmVpCurrentUAS The counter associated with the number of Unavailable Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.11`
atmVpCurrentSES The counter associated with the number of Severerly Errored Seconds, encountered by the VPL of this ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.12`
atmVpCurrentCDC Amount of cells dropped in the current 15 minute interval of the VP connection.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.13`
atmVpCurrentTotalDiscards The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.14`
atmVpCurrentClp0Discards The total number of valid ATM cells received with CLP=0 and discarded by the traffic policing entity.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.15`
atmVpCurrentTotalCellOuts The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.16`
atmVpCurrentClp0CellOuts The total number of valid ATM cells transmitted with CLP=0 by this VPL.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.17`
atmVpCurrentTaggedOuts The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.18`
atmVpCurrentPCR The maximum traffic rate encountered in the last interval of the VP connection (monitored once a second).	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.19`
atmVpCurrentSCR The average traffic rate during the last interval of the VP connection.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.20`
atmVpCurrentMCR MCR - The minimum traffic rate encountered in the last interval of the VP connection (monitored once a second).	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.21`
atmVpCurrentShaperTotalDiscards The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.22`
atmVpCurrentShaperClp0Discards The total number of CLP0 cells discarded due to congestion by the traffic shaper.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.23`
atmVpCurrentShaperClp1Discards The total number of CLP1 cells discarded due to congestion by the traffic shaper.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.1.1.24`

atmVpPMCurrentTable

table

.1.3.6.1.4.1.164.12.2.1.2.1.2 · 1 row entry · 16 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmVpPMCurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmVpPMCurrentTable'

The ATM VP Current table for Performance Management.

atmVpPMCurrentEntry row .1.3.6.1.4.1.164.12.2.1.2.1.2.1

An entry in the ATM VP Current table for Performance
Management.

Indexes

No indexes recorded

Column Syntax OID

atmVpPMCurrentVpi

The VPI of the VPL.

SNMPv2-SMIInteger32

Enumerated Values:

2	forward
3	backward

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.2.1.2.1.2.1.1

atmVpPMCurrentDir

The direction of performance management.

Enumeration

Constraints:
range: 1-96

.1.3.6.1.4.1.164.12.2.1.2.1.2.1.2

atmVpPMCurrentTxClp01

The counter associated with the number of transmitted
CLP 0+1 cells, encountered by the VPL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.2.1.3

atmVpPMCurrentTxClp0

The counter associated with the number of transmitted
CLP 0 cells, encountered by the VPL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.2.1.4

atmVpPMCurrentRxClp01

The counter associated with the number of received
CLP 0+1 cells, encountered by the VPL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.2.1.5

atmVpPMCurrentRxClp0

The counter associated with the number of received
CLP 0 cells, encountered by the VPL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.2.1.6

atmVpPMCurrentErroredCells

The counter associated with the number of errored
cells, encountered by the VPL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.2.1.7

atmVpPMCurrentLostCells

The counter associated with the number of lost
cells, encountered by the VPL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.2.1.8

atmVpPMCurrentMisinsertedCells

The counter associated with the number of misinserted
cells, encountered by the VPL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.2.1.9

atmVpPMCurrentECB

The counter associated with the number of ECB,
encountered by the VPL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.2.1.10

atmVpPMCurrentSECB

The counter associated with the number of SECB,
encountered by the VPL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.2.1.11

atmVpPMCurrentES

The counter associated with the number of
Errored Seconds, encountered by the VPL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.2.1.12

atmVpPMCurrentSES

The counter associated with the number of Severely
Errored Seconds, encountered by the VPL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.2.1.13

atmVpPMCurrentUAS

The counter associated with the number of Unavailable
Seconds, encountered by the VPL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.2.1.14

atmVpPMCurrentIntervalQuality

If the number of errors per interval is superior to
the atmNteUPLTCR value, the quality of service of
the interval is declared as unacceptable.

Enumeration

Enumerated Values:

2	normal
3	unacceptable

.1.3.6.1.4.1.164.12.2.1.2.1.2.1.15

atmVpPMCurrentLastDayQuality

If the number of errors per 24 hours is superior to
the atmNteDPLTCR value, the quality of service of
the day is declared as degraded.

Enumeration

Enumerated Values:

2	normal
4	degraded

.1.3.6.1.4.1.164.12.2.1.2.1.2.1.16

atmVpIntervalTable

table

.1.3.6.1.4.1.164.12.2.1.2.1.3 · 1 row entry · 25 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmVpIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmVpIntervalTable'

The ATM Vp Interval table.

atmVpIntervalEntry row .1.3.6.1.4.1.164.12.2.1.2.1.3.1

An entry in the ATM Vp Interval table.

Indexes

IF-MIBifIndex ATM-MIBatmVplVpi atmVpQoSPeriodRef

Column Syntax OID

atmVpIntervalVpi

The VPI of the VPL.

SNMPv2-SMIInteger32

Enumerated Values:

1	currentPeriod
2	lastPeriod

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.1

atmVpIntervalNumber

A number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals are valid).

Integer32

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.2

atmVpIntervalRxCellsClp01

The counter associated with the number of transmitted
cells , encountered by an ATM interface/VP in
one of the previous 96, individual 15 minute,
intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.3

atmVpIntervalRxCellsClp0

The counter associated with the number of received
cells, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.4

atmVpIntervalGcra0Violations

The counter associated with the number of
cells violating GCRA0, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.5

atmVpIntervalGcra1Violations

The counter associated with the number of
cells violating GCRA1, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.

SNMPv2-SMIGauge32

Enumerated Values:

2	forward
3	backward

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.6

atmVpIntervalRxAIS

The counter associated with the number of received
AIS cells, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.

SNMPv2-SMIGauge32

Enumerated Values:

1	currentPeriod
2	lastPeriod

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.7

atmVpIntervalTxAIS

The counter associated with the number of transmitted
AIS cells, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals. Not supported in the first phase.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.8

atmVpIntervalRxRDI

The counter associated with the number of received
RDI cells, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.9

atmVpIntervalTxRDI

The counter associated with the number of transmitted
RDI cells, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.10

atmVpIntervalContinuityLoss

The counter associated with the number of Continuity
Loss cells, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.11

atmVpIntervalUAS

The counter associated with the number of Unavailable
Seconds, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.12

atmVpIntervalSES

The counter associated with the number of Severerly Errored
Seconds, encountered by an ATM
interface/VP in one of the previous 96, individual 15
minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.13

atmVpIntervalCDC

Amount of cells dropped in the 15 minute interval
of the VP connection.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.14

atmVpIntervalTotalDiscards

The total number of valid ATM cells discarded by
the traffic policing entity. This includes cells
originally received with CLP=0 and CLP=1.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.15

atmVpIntervalClp0Discards

The total number of valid ATM cells received with
CLP=0 an discarded by the traffic policing
entity.

SNMPv2-SMIGauge32

Enumerated Values:

1	empty
2	full
3	below
4	above

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.16

atmVpIntervalTotalCellOuts

The total number of valid ATM cells transmitted
by this VPL. This includes both CLP=0 and CLP=1
cells.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.17

atmVpIntervalClp0CellOuts

The total number of valid ATM cells transmitted
with CLP=0 by this VPL.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.18

atmVpIntervalTaggedOuts

The total number of valid ATM cells tagged by the
traffic policing entity from CLP=0 to CLP=1 and
transmitted by this VPL.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.19

atmVpIntervalPCR

The maximum traffic rate encountered in the last
interval of the VP connection (monitored once a second)
encountered by an ATM interface/VP in one of the previous
96, individual 15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.20

atmVpIntervalSCR

The average traffic rate during the last interval of the
VP connection , encountered by an ATM interface/VP in one
of the previous 96, individual 15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.21

atmVpIntervalMCR

MCR - The minimum traffic rate encountered in the last
interval of the VP connection (monitored once a second)
encountered by an ATM interface/VP in one of the previous
96, individual 15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.22

atmVpIntervalShaperTotalDiscards

The total number of cells (CLP0 and CLP1) discarded
due to congestion by the traffic shaper.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.23

atmVpIntervalShaperClp0Discards

The total number of CLP0 cells discarded
due to congestion by the traffic shaper.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.24

atmVpIntervalShaperClp1Discards

The total number of CLP1 cells discarded
due to congestion by the traffic shaper.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.3.1.25

atmVpPMIntervalTable

table

.1.3.6.1.4.1.164.12.2.1.2.1.4 · 1 row entry · 17 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmVpPMIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmVpPMIntervalTable'

The ATM Vp Interval table for Performance Management.

atmVpPMIntervalEntry row .1.3.6.1.4.1.164.12.2.1.2.1.4.1

An entry in the ATM Vp Interval table for Performance
Management.

Indexes

No indexes recorded

Column	Syntax	OID
atmVpPMIntervalVpi The VPI of the VPL.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.2.1.2.1.4.1.1`
atmVpPMIntervalDir The direction of performance management.	Enumeration	`.1.3.6.1.4.1.164.12.2.1.2.1.4.1.2`
atmVpPMIntervalNumber A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).	Integer32	`.1.3.6.1.4.1.164.12.2.1.2.1.4.1.3`
atmVpPMIntervalTxClp01 The counter associated with the number of transmitted CLP 0+1 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.4.1.4`
atmVpPMIntervalTxClp0 The counter associated with the number of transmitted CLP 0 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.4.1.5`
atmVpPMIntervalRxClp01 The counter associated with the number of received CLP 0+1 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.4.1.6`
atmVpPMIntervalRxClp0 The counter associated with the number of received CLP 0 cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.4.1.7`
atmVpPMIntervalErroredCells The counter associated with the number of Errored cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.4.1.8`
atmVpPMIntervalLostCells The counter associated with the number of Lost cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.4.1.9`
atmVpPMIntervalMisinsertedCells The counter associated with the number of Misinserted cells, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.4.1.10`
atmVpPMIntervalECB The counter associated with the number of ECBs encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.4.1.11`
atmVpPMIntervalSECB The counter associated with the number of SECBs encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.4.1.12`
atmVpPMIntervalES The counter associated with the number of Errored Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.4.1.13`
atmVpPMIntervalSES The counter associated with the number of Severely Errored Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.4.1.14`
atmVpPMIntervalUAS The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VP in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.4.1.15`
atmVpPMIntervalQuality If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.	Enumeration	`.1.3.6.1.4.1.164.12.2.1.2.1.4.1.16`
atmVpPMIntervalLastDayQuality If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.	Enumeration	`.1.3.6.1.4.1.164.12.2.1.2.1.4.1.17`

atmVpQoSTable

table

.1.3.6.1.4.1.164.12.2.1.2.1.5 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmVpQoSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmVpQoSTable'

The VP QoS table.

atmVpQoSEntry row .1.3.6.1.4.1.164.12.2.1.2.1.5.1

Indexes

No indexes recorded

Column	Syntax	OID
atmVpQoSPeriodRef This object is an index that specifies which period of time, the next 2 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllSta…	Enumeration	`.1.3.6.1.4.1.164.12.2.1.2.1.5.1.1`
atmVpQoSElapsedTime Elapsed Time in seconds. - for atmVpQoSPeriodRef = currentPeriod: The period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStatsCmd was received since Start-up) until now. - for …	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.2.1.2.1.5.1.2`
atmVpQoSUAS Number of Unavailable Seconds for the reference period (atmVpQoSPeriodRef).	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.5.1.3`

atmVpPMQoSTable

table

.1.3.6.1.4.1.164.12.2.1.2.1.6 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmVpPMQoSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmVpPMQoSTable'

The PM VP QoS table.

atmVpPMQoSEntry row .1.3.6.1.4.1.164.12.2.1.2.1.6.1

Indexes

No indexes recorded

Column	Syntax	OID
atmVpPMQoSDirection The direction of performance management.	Enumeration	`.1.3.6.1.4.1.164.12.2.1.2.1.6.1.1`
atmVpPMQoSPeriodRef This object is an index that specifies which period of time, the next 5 objects refer to. currentPeriod - the period since last systemResetAllStatsCmd received or since Start-up (if no systemResetAllStat…	Enumeration	`.1.3.6.1.4.1.164.12.2.1.2.1.6.1.2`
atmVpPMQoSCLR Cell Loss Ratio counter for the reference period (atmVpPMQoSPeriodRef)- defined in accordance with I.356 , in %. The value will be multipuled by 100.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.6.1.3`
atmVpPMQoSCER Cell Error Ratio counter for the reference period (atmVpPMQoSPeriodRef) defined in accordance with I.356 , in %. The value will be multipuled by 100.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.6.1.4`
atmVpPMQoSCMR Cell Misinsertion Ratio counter for the reference period (atmVpPMQoSPeriodRef) defined in accordance with I.356 , cells/sec .	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.1.6.1.5`

atmVpShaperStatTable

table

.1.3.6.1.4.1.164.12.2.1.2.1.7 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmVpShaperStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmVpShaperStatTable'

The ATM VP shaper statistics table.

atmVpShaperStatEntry row .1.3.6.1.4.1.164.12.2.1.2.1.7.1

An entry in the ATM VP shaper statistics table.

Indexes

No indexes recorded

Column Syntax OID

atmVpShaperDiscarded

The number of Cells that were discarded in the shaper on that VPC due
to buffer overflow.
This counter counts till it reaches its MAX value (20 bits) and then
rolls over.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.7.1.1

atmVpShaperOccupation

The number of Cells that are currently stored in the buffer.
This parameter is limited to 20 bits.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.2.1.2.1.7.1.2

atmVpShaperMaxOccupation

The Maximum number of Cells that were stored in the buffer,
since this VP was activated. This parameter is limited to 20 bits.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.2.1.2.1.7.1.3

atmVpShaperLevel

The occupation of the buffer according to a predefined threshold.
empty - buffer is Empty
full - buffer is Full
below - buffer is Below the threshold
above - buffer is Above the threshold. This is also the trigger to …

Enumeration

.1.3.6.1.4.1.164.12.2.1.2.1.7.1.4

atmVpShaperEpdDropped

The number of Cells that were dropped in the shaper on that VPC
due to EPD\PPD mechanism in the last second.
This parameter is limited to 24 bits.
Applicable for a EPD/PPD VP only.

SNMPv2-SMICounter32

Enumerated Values:

2	normal
3	unacceptable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.7.1.5

atmVpShaperTotalEpdDropped

The Total number of Cells that were dropped in the shaper on that
VPC due to EPD\PPD mechanism in the last 15 minutes. This counter
automatically reset itself every 15 minutes.
Applicable for a EPD/PPD VP only.

SNMPv2-SMICounter32

Enumerated Values:

2	normal
4	degraded

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.1.7.1.6

atmVcCurrentTable

table

.1.3.6.1.4.1.164.12.2.1.2.2.1 · 1 row entry · 25 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmVcCurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmVcCurrentTable'

The ATM VC Current table.

atmVcCurrentEntry row .1.3.6.1.4.1.164.12.2.1.2.2.1.1

An entry in the ATM VC Current table.

Indexes

IF-MIBifIndex atmVcIntervalVpi atmVcIntervalVci atmVcIntervalNumber

Column	Syntax	OID
atmVcCurrentVpi The VPI of the VCL.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.1`
atmVcCurrentVci The VCI of the VCL.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.2`
atmVcCurrentRxCellsClp01 The counter associated with the number of transmitted cells, encountered by the VCL of this ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Constraints: `range: 1-96`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.3`
atmVcCurrentRxCellsClp0 The counter associated with the number of received cells, encountered by the VCL of this ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.4`
atmVcCurrentGcra0Violations The counter associated with the number of cells violating GCRA0, encountered by the VCL of this ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.5`
atmVcCurrentGcra1Violations The counter associated with the number of cells violating GCRA1, encountered by the VCL of this ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.6`
atmVcCurrentRxAIS The counter associated with the number of received AIS cells, encountered by the VCL of this ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.7`
atmVcCurrentTxAIS The counter associated with the number of transmitted AIS cells, encountered by the VCL of this ATM interface in the current 15 minute interval. Not Supported in the first phase.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.8`
atmVcCurrentRxRDI The counter associated with the number of received RDI cells, encountered by the VCL of this ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.9`
atmVcCurrentTxRDI The counter associated with the number of transmitted RDI cells, encountered by the VCL of this ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.10`
atmVcCurrentContinuityLoss The counter associated with the number of loss of continuity cells, encountered by the VCL of this ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.11`
atmVcCurrentUAS The counter associated with the number of Unavailable Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.12`
atmVcCurrentSES The counter associated with the number of Severerly Errored Seconds, encountered by the VCL of this ATM interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.13`
atmVcCurrentCDC Amount of cells dropped in the current 15 minute interval of the VC connection.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.14`
atmVcCurrentTotalDiscards The total number of valid ATM cells discarded by the traffic policing entity. This includes cells originally received with CLP=0 and CLP=1.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.15`
atmVcCurrentClp0Discards The total number of valid ATM cells received with CLP=0 an discarded by the traffic policing entity.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.16`
atmVcCurrentTotalCellOuts The total number of valid ATM cells transmitted by this VPL. This includes both CLP=0 and CLP=1 cells.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.17`
atmVcCurrentClp0CellOuts The total number of valid ATM cells transmitted with CLP=0 by this VPL.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.18`
atmVcCurrentTaggedOuts The total number of valid ATM cells tagged by the traffic policing entity from CLP=0 to CLP=1 and transmitted by this VPL.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.19`
atmVcCurrentPCR The maximum traffic rate encountered in the last interval of the VC connection (monitored once a second).	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.20`
atmVcCurrentSCR The average traffic rate during the last interval of the VC connection.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.21`
atmVcCurrentMCR MCR - The minimum traffic rate encountered in the last interval of the VC connection (monitored once a second).	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.22`
atmVcCurrentShaperTotalDiscards The total number of cells (CLP0 and CLP1) discarded due to congestion by the traffic shaper.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.23`
atmVcCurrentShaperClp0Discards The total number of CLP0 cells discarded due to congestion by the traffic shaper.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.24`
atmVcCurrentShaperClp1Discards The total number of CLP1 cells discarded due to congestion by the traffic shaper.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.1.1.25`

atmVcPMCurrentTable

table

.1.3.6.1.4.1.164.12.2.1.2.2.2 · 1 row entry · 17 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmVcPMCurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmVcPMCurrentTable'

The ATM VC Current table for Performance Management.

atmVcPMCurrentEntry row .1.3.6.1.4.1.164.12.2.1.2.2.2.1

An entry in the ATM VC Current table for Performance
Management.

Indexes

No indexes recorded

Column Syntax OID

atmVcPMCurrentVpi

The VPI of the VCL.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.2.1.2.2.2.1.1

atmVcPMCurrentVci

The VCI of the VCL.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.2.1.2.2.2.1.2

atmVcPMCurrentDir

The direction of Performance Management.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.2.1.2.2.2.1.3

atmVcPMCurrentTxClp01

The counter associated with the number of transmitted
CLP 0+1 cells, encountered by the VCL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Enumerated Values:

2	forward
3	backward

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.2.1.4

atmVcPMCurrentTxClp0

The counter associated with the number of transmitted
CLP 0 cells, encountered by the VCL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Constraints:
range: 1-96

.1.3.6.1.4.1.164.12.2.1.2.2.2.1.5

atmVcPMCurrentRxClp01

The counter associated with the number of received
CLP 0+1 cells, encountered by the VCL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.2.1.6

atmVcPMCurrentRxClp0

The counter associated with the number of received
CLP 0 cells, encountered by the VCL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.2.1.7

atmVcPMCurrentErroredCells

The counter associated with the number of errored
cells, encountered by the VCL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.2.1.8

atmVcPMCurrentLostCells

The counter associated with the number of lost
cells, encountered by the VCL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.2.1.9

atmVcPMCurrentMisinsertedCells

The counter associated with the number of misinserted
cells, encountered by the VCL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.2.1.10

atmVcPMCurrentECB

The counter associated with the number of ECBs
encountered by the VCL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.2.1.11

atmVcPMCurrentSECB

The counter associated with the number of SECBs
encountered by the VCL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.2.1.12

atmVcPMCurrentES

The counter associated with the number of
Errored Seconds, encountered by the VCL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.2.1.13

atmVcPMCurrentSES

The counter associated with the number of Severely
Errored Seconds, encountered by the VCL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.2.1.14

atmVcPMCurrentUAS

The counter associated with the number of Severely
Errored Seconds, encountered by the VCL of this ATM
interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.2.1.15

atmVcPMCurrentIntervalQuality

If the number of errors per interval is superior to
the atmNteUPLTCR value, the quality of service of
the interval is declared as unacceptable.

Enumeration

.1.3.6.1.4.1.164.12.2.1.2.2.2.1.16

atmVcPMCurrentLastDayQuality

If the number of errors per 24 hours is superior to
the atmNteDPLTCR value, the quality of service of
the day is declared as degraded.

Enumeration

.1.3.6.1.4.1.164.12.2.1.2.2.2.1.17

atmVcIntervalTable

table

.1.3.6.1.4.1.164.12.2.1.2.2.3 · 1 row entry · 26 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmVcIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmVcIntervalTable'

The ATM Vc Interval table.

atmVcIntervalEntry row .1.3.6.1.4.1.164.12.2.1.2.2.3.1

An entry in the ATM Vc Interval table.

Indexes

No indexes recorded

Column Syntax OID

atmVcIntervalVpi

The VPI of the VCL.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.1

atmVcIntervalVci

The VCI of the VCL.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.2

atmVcIntervalNumber

A number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals are valid).

Integer32

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.3

atmVcIntervalRxCellsClp01

The counter associated with the number of transmitted
cells , encountered by an ATM interface/VC in
one of the previous 96, individual 15 minute,
intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.4

atmVcIntervalRxCellsClp0

The counter associated with the number of received
cells, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.5

atmVcIntervalGcra0Violations

The counter associated with the number of
cells violating GCRA0, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.6

atmVcIntervalGcra1Violations

The counter associated with the number of
cells violating GCRA1, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.7

atmVcIntervalRxAIS

The counter associated with the number of received
AIS cells, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.8

atmVcIntervalTxAIS

The counter associated with the number of transmitted
AIS cells, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals. Not supported in the first phase.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.9

atmVcIntervalRxRDI

The counter associated with the number of received
RDI cells, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.

SNMPv2-SMIGauge32

Enumerated Values:

1	currentPeriod
2	lastPeriod

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.10

atmVcIntervalTxRDI

The counter associated with the number of transmitted
RDI cells, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.11

atmVcIntervalContinuityLoss

The counter associated with the number of Continuity
Loss cells, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.12

atmVcIntervalUAS

The counter associated with the number of Unavailable
Seconds, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.13

atmVcIntervalSES

The counter associated with the number of Severerly Errored
Seconds, encountered by an ATM
interface/VC in one of the previous 96, individual 15
minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.14

atmVcIntervalCDC

Amount of cells dropped in the 15 minute interval
of the VC connection.

SNMPv2-SMIGauge32

Enumerated Values:

2	forward
3	backward

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.15

atmVcIntervalTotalDiscards

The total number of valid ATM cells discarded by
the traffic policing entity. This includes cells
originally received with CLP=0 and CLP=1.

SNMPv2-SMIGauge32

Enumerated Values:

1	currentPeriod
2	lastPeriod

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.16

atmVcIntervalClp0Discards

The total number of valid ATM cells received with
CLP=0 an discarded by the traffic policing
entity.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.17

atmVcIntervalTotalCellOuts

The total number of valid ATM cells transmitted
by this VPL. This includes both CLP=0 and CLP=1
cells.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.18

atmVcIntervalClp0CellOuts

The total number of valid ATM cells transmitted
with CLP=0 by this VPL.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.19

atmVcIntervalTaggedOuts

The total number of valid ATM cells tagged by the
traffic policing entity from CLP=0 to CLP=1 and
transmitted by this VPL.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.20

atmVcIntervalPCR

The maximum traffic rate encountered in the
last interval of the VC connection (monitored once a second)
encountered by an ATM interface/VC in one of the previous 96,
individual 15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.21

atmVcIntervalSCR

The average traffic rate during the last interval
of the VC connection, encountered by an ATM interface/VC
in one of the previous 96, individual 15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.22

atmVcIntervalMCR

MCR - The minimum traffic rate encountered in the last
interval of the VC connection (monitored once a second)
encountered by an ATM interface/VC in one of the previous 96,
individual 15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.23

atmVcIntervalShaperTotalDiscards

The total number of cells (CLP0 and CLP1) discarded
due to congestion by the traffic shaper.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.24

atmVcIntervalShaperClp0Discards

The total number of CLP0 cells discarded
due to congestion by the traffic shaper.

SNMPv2-SMIGauge32

Enumerated Values:

1	empty
2	full
3	below
4	above

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.25

atmVcIntervalShaperClp1Discards

The total number of CLP1 cells discarded
due to congestion by the traffic shaper.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.3.1.26

atmVcPMIntervalTable

table

.1.3.6.1.4.1.164.12.2.1.2.2.4 · 1 row entry · 18 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmVcPMIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmVcPMIntervalTable'

The ATM Vc Interval table for Performance Management.

atmVcPMIntervalEntry row .1.3.6.1.4.1.164.12.2.1.2.2.4.1

An entry in the ATM Vc Interval table for Performance
Management.

Indexes

No indexes recorded

Column	Syntax	OID
atmVcPMIntervalVpi The VPI of the VCL.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.2.1.2.2.4.1.1`
atmVcPMIntervalVci The VCI of the VCL.	SNMPv2-SMIInteger32 Constraints: `range: 1-96`	`.1.3.6.1.4.1.164.12.2.1.2.2.4.1.2`
atmVcPMIntervalDir The direction of Performance Management.	Enumeration	`.1.3.6.1.4.1.164.12.2.1.2.2.4.1.3`
atmVcPMIntervalNumber A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).	Integer32	`.1.3.6.1.4.1.164.12.2.1.2.2.4.1.4`
atmVcPMIntervalTxClp01 The counter associated with the number of transmitted CLP 0+1 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.4.1.5`
atmVcPMIntervalTxClp0 The counter associated with the number of transmitted CLP 0 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.4.1.6`
atmVcPMIntervalRxClp01 The counter associated with the number of received CLP 0+1 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.4.1.7`
atmVcPMIntervalRxClp0 The counter associated with the number of received CLP 0 cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.4.1.8`
atmVcPMIntervalErroredCells The counter associated with the number of Errored cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.4.1.9`
atmVcPMIntervalLostCells The counter associated with the number of Lost cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.4.1.10`
atmVcPMIntervalMisinsertedCells The counter associated with the number of Misinserted cells, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.4.1.11`
atmVcPMIntervalECB The counter associated with the number of ECBs encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Constraints: `range: 1-2048`	`.1.3.6.1.4.1.164.12.2.1.2.2.4.1.12`
atmVcPMIntervalSECB The counter associated with the number of SECBs encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Constraints: `range: 80-80`	`.1.3.6.1.4.1.164.12.2.1.2.2.4.1.13`
atmVcPMIntervalES The counter associated with the number of Errored Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.4.1.14`
atmVcPMIntervalSES The counter associated with the number of Severely Errored Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.4.1.15`
atmVcPMIntervalUAS The counter associated with the number of Unavailable Seconds, encountered by an ATM interface/VC in one of the previous 96, individual 15 minute, intervals.	SNMPv2-SMIGauge32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.4.1.16`
atmVcPMIntervalQuality If the number of errors per interval is superior to the atmNteUPLTCR value, the quality of service of the interval is declared as unacceptable.	Enumeration	`.1.3.6.1.4.1.164.12.2.1.2.2.4.1.17`
atmVcPMIntervalLastDayQuality If the number of errors per 24 hours is superior to the atmNteDPLTCR value, the quality of service of the day is declared as degraded.	Enumeration	`.1.3.6.1.4.1.164.12.2.1.2.2.4.1.18`

atmCESAAL1StatsTable

table

.1.3.6.1.4.1.164.12.2.1.2.2.5 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmCESAAL1StatsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmCESAAL1StatsTable'

This table shows statistics of the structured Circuit-Emulation connections.

atmCESAAL1StatsEntry row .1.3.6.1.4.1.164.12.2.1.2.2.5.1

defines an entry in the atmCESAAL1StatsTable

Indexes

No indexes recorded

Column	Syntax	OID
atmCESAAL1SeqErrors number of cells discarded due to wrong sequence number	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.5.1.1`
atmCESAAL1HdrErrors number of cells discarded due to bad AAL1 header error. this include correctable and uncorrectable CRC, plus bad parity.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.5.1.2`
atmCESAAL1PointerReframes number of events in which the AAL1 reassembler found that an SDT pointer isn't where it is expected, and the pointer must be reacquired.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.5.1.3`
atmCESAAL1BufUnderflows number of buffer underflows events.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.5.1.4`
atmCESAAL1BufOverflows number of buffer overflows events.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.5.1.5`

atmVcQoSTable

table

.1.3.6.1.4.1.164.12.2.1.2.2.6 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmVcQoSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmVcQoSTable'

The ATM VP QoS table.

atmVcQoSEntry row .1.3.6.1.4.1.164.12.2.1.2.2.6.1

An entry in the ATM VP table.

Indexes

No indexes recorded

Column Syntax OID

atmVcQoSPeriodRef

This object is an index that specifies which period of time, the next
2 objects refer to.
currentPeriod - the period since last systemResetAllStatsCmd received or
since Start-up (if no systemResetAllS…

Enumeration

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.12.2.1.2.2.6.1.1

atmVcQoSElapsedTime

Elapsed Time in seconds.
- for atmVcQoSPeriodRef = currentPeriod:
The period since last systemResetAllStatsCmd received or since Start-up
(if no systemResetAllStatsCmd was received since Start-up) until now.
- for …

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.2.1.2.2.6.1.2

atmVcQoSUAS

Number of Unavailable Seconds for the reference period (atmVcQoSPeriodRef).

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.6.1.3

atmVcPMQoSTable

table

.1.3.6.1.4.1.164.12.2.1.2.2.7 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmVcPMQoSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmVcPMQoSTable'

The PM VC QoS table.

atmVcPMQoSEntry row .1.3.6.1.4.1.164.12.2.1.2.2.7.1

An entry in the VC PM QoS table.

Indexes

No indexes recorded

Column Syntax OID

atmVcPMQoSDirection

The direction of performance management.

Enumeration

.1.3.6.1.4.1.164.12.2.1.2.2.7.1.1

atmVcPMQoSPeriodRef

This object is an index that specifies which period of time, the next
5 objects refer to.
currentPeriod - the period since last systemResetAllStatsCmd received or
since Start-up (if no systemResetAllStat…

Enumeration

.1.3.6.1.4.1.164.12.2.1.2.2.7.1.2

atmVcPMQoSCLR

Cell Loss Ratio counter for the reference period (atmVcPMQoSPeriodRef)-
defined in accordance with I.356 , in %.
The value will be multipuled by 100.

SNMPv2-SMIGauge32

Enumerated Values:

1	off
2	on

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.7.1.3

atmVcPMQoSCER

Cell Error Ratio counter for the reference period (atmVcPMQoSPeriodRef)
defined in accordance with I.356 , in %.
The value will be multipuled by 100.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.7.1.4

atmVcPMQoSCMR

Cell Miss-insertion Ratio counter for the reference period (atmVcPMQoSPeriodRef)
defined in accordance with I.356 , cells/sec .

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.1.2.2.7.1.5

atmVcShaperStatTable

table

.1.3.6.1.4.1.164.12.2.1.2.2.8 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmVcShaperStatTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmVcShaperStatTable'

The ATM VC shaper statistics table.

atmVcShaperStatEntry row .1.3.6.1.4.1.164.12.2.1.2.2.8.1

An entry in the ATM VC shaper statistics table.

Indexes

No indexes recorded

Column	Syntax	OID
atmVcShaperDiscarded The number of Cells that were discarded in the shaper on that VCC due to buffer overflow. This counter counts till it reaches its MAX value (20 bits) and then rolls over.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.8.1.1`
atmVcShaperOccupation The number of Cells that are currently stored in the buffer. This parameter is limited to 20 bits.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.2.1.2.2.8.1.2`
atmVcShaperMaxOccupation The Maximum number of Cells that were stored in the buffer, since this VC was activated. This parameter is limited to 20 bits.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.2.1.2.2.8.1.3`
atmVcShaperLevel The occupation of the buffer according to a predefined threshold. empty - buffer is Empty full - buffer is Full below - buffer is Below the threshold above - buffer is Above the threshold. This is also the trigger to …	Enumeration	`.1.3.6.1.4.1.164.12.2.1.2.2.8.1.4`
atmVcShaperEpdDropped The number of Cells that were dropped in the shaper on that VCC due to EPD\PPD mechanism in the last second. This parameter is limited to 24 bits. Applicable for a EPD/PPD VC only.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.8.1.5`
atmVcShaperTotalEpdDropped The Total number of Cells that were dropped in the shaper on that VPC due to EPD\PPD mechanism in the last 15 minutes. This counter automatically reset itself every 15 minutes. Applicable for a EPD/PPD VC only.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.12.2.1.2.2.8.1.6`

atmIntervalDateTable

table

.1.3.6.1.4.1.164.12.2.1.3 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmIntervalDateTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmIntervalDateTable'

The agent will keep in this group the date & time
corresponding to each interval.

atmIntervalDateEntry row .1.3.6.1.4.1.164.12.2.1.3.1

The date & time for the given interval.

Indexes

No indexes recorded

Column Syntax OID

atmIntervalDateInterval

The interval number defining this entry.

Integer32

Enumerated Values:

2	no
3	yes

.1.3.6.1.4.1.164.12.2.1.3.1.1

atmIntervalDateDate

The date corresponding to this interval.

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.12.2.1.3.1.2

atmIntervalDateTime

The time corresponding to this interval.

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.12.2.1.3.1.3

atmGenSysSelfTestTable

table

.1.3.6.1.4.1.164.12.2.2.1.1 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmGenSysSelfTestTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmGenSysSelfTestTable'

A table containing the results of the initial testing of the device.

atmGenSysSelfTestEntry row .1.3.6.1.4.1.164.12.2.2.1.1.1

An entry in table.

Indexes

atmNteOamMode atmNteOamCellType atmNteOamLevel

Column Syntax OID

atmGenSysSelfTestIndex

A running index for the table.

SNMPv2-SMIInteger32

Enumerated Values:

endToEnd

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.2.2.1.1.1.1

atmGenSysSelfTestResult

The results of the initial testing of the device.

SNMPv2-TCDisplayString

Enumerated Values:

1	aisAndRdi
2	loopback

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.12.2.2.1.1.1.2

atmGenSysSelfTestModule

The name of module on which the test was performed.

SNMPv2-TCDisplayString

Enumerated Values:

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.12.2.2.1.1.1.3

atmGenSysLogTable

table

.1.3.6.1.4.1.164.12.2.2.1.3 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmGenSysLogTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmGenSysLogTable'

A copy of the log buffer.

atmGenSysLogEntry row .1.3.6.1.4.1.164.12.2.2.1.3.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
atmGenSysLogIndex The index of the log buffer.	Integer32	`.1.3.6.1.4.1.164.12.2.2.1.3.1.1`
atmGenSysLogMessage The log buffer entry message text.	OctetString	`.1.3.6.1.4.1.164.12.2.2.1.3.1.2`

atmGenSysCxRefTable

table

.1.3.6.1.4.1.164.12.2.2.1.5 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmGenSysCxRefTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmGenSysCxRefTable'

A Cross Reference table. The table maintains 
an index of an object which is also the table index, 
and a counter that indicates how many times this 
object was referenced.
When using this table for more than one referenced table,
			which uses the same range of indexes, then the index 
			should be shifted by a unique offset per table.
             
In ACE2002 this table is used for TD and for FR Desc. Thus,
the index for FR Descriptor is: FR Descriptor index + offset. 
The offset is described in the ACE2002 NMS SRS.

atmGenSysCxRefEntry row .1.3.6.1.4.1.164.12.2.2.1.5.1

The entries will be added by the agent upon
an entry addition in the referenced tables
(TD table, FR Descriptor etc.)

Indexes

No indexes recorded

Column Syntax OID

atmGenSysCxRefIndex

The index specifies an entry in the table of the object.

SNMPv2-SMIInteger32

Enumerated Values:

0	physical
1	atm

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.2.2.1.5.1.1

atmGenSysCxRefCounter

The counter counts the number of references
that have been made to the object .

SNMPv2-SMIGauge32

Enumerated Values:

1	manual
2	automatic

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.2.2.1.5.1.2

atmNteManagerTable

table

.1.3.6.1.4.1.164.12.3.1.1.1 · 1 row entry · 13 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmNteManagerTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmNteManagerTable'

The Manager Table includes all the NMSs that
receive traps from this agent. A single manager
can receive traps on more than one PVC. The agent 
will set	implicitly the correct ifIndex, VPI, VCI 
values to all relevant entries in the table when 
the user changes	them for one of the PVCs.

atmNteManagerEntry row .1.3.6.1.4.1.164.12.3.1.1.1.1

A single manager and the PVC for receiving traps.

Indexes

No indexes recorded

Column Syntax OID

atmNteManagerIP

The IP address of the NMS.

RFC1155-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.164.12.3.1.1.1.1.1

atmNteManagerPvc

A PVC index. The range is 1..8. There are four PVCs
on the User Port and four PVCs on the Network Port.
The default VPI, VCI values are specified below.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.1.1.1.1.2

atmNteManagerIfIndex

The ATM interface index of the management port.

SNMPv2-SMIInteger32r/w

Constraints:
range: 1-64

.1.3.6.1.4.1.164.12.3.1.1.1.1.3

atmNteManagerVpi

The VPI of the management VCL. Default: 0.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.1.1.1.1.4

atmNteManagerVci

The VCI of the management VCL. Defaults: 32,33,34,35.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.1.1.1.1.5

atmNteManagerTrapMask

SNMPv2-SMIInteger32r/w

Constraints:
range: 1-64

.1.3.6.1.4.1.164.12.3.1.1.1.1.6

atmNteManagerRowStatus

Creation/Deletion of rows in the table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.12.3.1.1.1.1.7

atmNteManagerNextHop

This parameter is relevant to Ethernet out of band
host only (PVC=10).
The Next Hop IP address of the entry route.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.12.3.1.1.1.1.8

atmNteManagerVlanSupport

VLAN support (Tagging).
no - No support to VLAN.
yes - 4 VLAN bytes will be added to the frame.

Enumerationr/w

Enumerated Values:

1	scheduling
2	schedulingAndShaping
3	policing

.1.3.6.1.4.1.164.12.3.1.1.1.1.9

atmNteManagerVlanIdentifier

VLAN ID. Range is 0..4095.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.1.1.1.1.10

atmNteManagerVlanFramePriority

VLAN Frame priority.Range is 0..7.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.1.1.1.1.11

atmNteManagerAlarmTrapMask

The value of this object determines the alarm traps that the
agent should mask and not send to this NMS.

The value is an Octet String, where each bit is assigned to a certain
trap.
If the bit = 1, the t…

OctetStringr/w

.1.3.6.1.4.1.164.12.3.1.1.1.1.12

atmNteManagerConfigPorts

This variable defines from which port/s this manager can configure the device.
For IPmux 11 the value of this variable will be according to the ports
combination:
Network =1
User1=2
User2=4
(For Example: All ports = 7).

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.1.1.1.1.13

atmNteConfOamIfTable

table

.1.3.6.1.4.1.164.12.3.1.1.9.4 · 1 row entry · 1 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmNteConfOamIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmNteConfOamIfTable'

OAM support per ATM interface.

atmNteConfOamIfEntry row .1.3.6.1.4.1.164.12.3.1.1.9.4.1

Indexes

No indexes recorded

Column Syntax OID

atmNteConfOamIfAisRdi

This parameter controls the generation of F4/F5
AIS and RDI due to lower order problems such as physical
layer problems.

For AIS: Defines if F4/F5 AIS cell is transmitted due
to problems such as physic…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	notActive
3	active
4	inProgress
5	empty

.1.3.6.1.4.1.164.12.3.1.1.9.4.1.1

atmNteHostIfTable

table

.1.3.6.1.4.1.164.12.3.1.1.11 · 1 row entry · 13 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmNteHostIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmNteHostIfTable'

Host IP interface table.

atmNteHostIfEntry row .1.3.6.1.4.1.164.12.3.1.1.11.1

Indexes

No indexes recorded

Column Syntax OID

atmNteHostPvcIndex

A PVC index. The range is 1..10.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.1.1.11.1.1

atmNteHostIP

The host interface IP address.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.12.3.1.1.11.1.2

atmNteHostMask

The host interface subnet mask.

RFC1155-SMIIpAddressr/w

Constraints:
range: 1-96

.1.3.6.1.4.1.164.12.3.1.1.11.1.3

atmNteHostAtmIfIndex

ATM interface index. Will be 1
for user port, and 2 for network port.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.1.1.11.1.4

atmNteHostVpi

VPI of the PVC connected to that host interface.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.1.1.11.1.5

atmNteHostVci

VCI of the PVC connected to that host interface.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.1.1.11.1.6

atmNteHostRowStatus

Creation/Deletion of rows in the table.

SNMPv2-TCRowStatusr/w

Enumerated Values:

2	internal
3	external
4	loopback
5	adaptive

Description:

.1.3.6.1.4.1.164.12.3.1.1.11.1.7

atmNteHostRdnVpi

The VPI of the redundant management VCL.
This parameter is applicable only if atmNteRdnManagement=enable(3).

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	internal
3	external
4	disable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.1.1.11.1.8

atmNteHostRdnVci

The VCI of the redundant management VCL.
This parameter is applicable only if atmNteRdnManagement=enable(3).

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	other
2	sonet
3	sdh
4	direct
5	plcpInternal
6	plcpExternal
7	e3
8	ethCrcTrans
9	ethCrcNotTrans
10	directNoScrmbling
11	plcpInternalNoScrmbling
12	plcpExternalNoScrmbling

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.1.1.11.1.9

atmNteHostDefaultNextHop

The host interface Default Next Hop address.
This address will be used as default next hop for
every Bundle mapped to this Host.

RFC1155-SMIIpAddressr/w

Enumerated Values:

1	notApplicable
2	sc13m-155
3	st13s-155
4	st13l-155
5	utp-155
6	cx-bnc-155
7	e3
8	t3
9	e1
10	e1-ltu
11	fc13l-155
12	fc13lh-155
13	fc15lh-155
14	fc13l-e3
15	fc13lh-e3
16	fc15lh-e3
17	fc13l-t3
18	fc13lh-t3
19	fc15lh-t3

Type Constraints:
range: 4

.1.3.6.1.4.1.164.12.3.1.1.11.1.10

atmNteHostVlanTagging

VLAN Tag support.
no - No support to VLAN.
yes - 4 VLAN bytes will be added
to each frame connected to this Host.

Enumerationr/w

Enumerated Values:

2	bits15
3	bits17

.1.3.6.1.4.1.164.12.3.1.1.11.1.11

atmNteHostDefaultVlanID

Default VLAN ID of this Host.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	disable
2	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.1.1.11.1.12

atmNteHostDefaultVlanPriority

Default VLAN priority for this Host.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.1.1.11.1.13

atmNteOamTable

table

.1.3.6.1.4.1.164.12.3.1.1.26 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmNteOamTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmNteOamTable'

This table is a static table, which is created by agent once
upon initialization. The created entries are actually, only the
supported OAM features. 
This table enables addition of new features by adding new entries
rather than adding scalar parameters.
An OAM feature is defined by the indexes values combination.

atmNteOamEntry row .1.3.6.1.4.1.164.12.3.1.1.26.1

An entry in the OAM table.
Each entry in this table will indicate a special OAM.

Indexes

No indexes recorded

Column Syntax OID

atmNteOamMode

The OAM cell path.
endToEnd(1) - the entire path.

Enumeration

.1.3.6.1.4.1.164.12.3.1.1.26.1.1

atmNteOamCellType

This object indicates a unique Indication Signal.
aisAndRdi(1) - Alarm Indication Signal (AIS) and
Remote Defect Indication (RDI) cell.
loopback(2) - Loopback cell.

Enumeration

.1.3.6.1.4.1.164.12.3.1.1.26.1.2

atmNteOamLevel

The level of the OAM cell.
-- f4 (2) - VP level,
f5 (3) - VC level.

Enumeration

Enumerated Values:

2	segmentTermination
3	endToEndTermination

.1.3.6.1.4.1.164.12.3.1.1.26.1.3

atmNteOamEnable

This parameter determines if the specified OAM cells
will be enabled.

Enumerationr/w

Enumerated Values:

2	disabled
3	ais
4	rdi
5	aisAndRdi

.1.3.6.1.4.1.164.12.3.1.1.26.1.4

atmAlarmForwardingTable

table

.1.3.6.1.4.1.164.12.3.1.1.32 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmAlarmForwardingTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmAlarmForwardingTable'

The Alarm Forwarding Mechanism will be operated 
for this table entries.

atmAlarmForwardingEntry row .1.3.6.1.4.1.164.12.3.1.1.32.1

Each entry in this table is a pair of ports that
the Alarm Forwarding Mechanism is determined for.

Indexes

IF-MIBifIndex

Column Syntax OID

atmAlarmForwardingFailPort

An Index of the port on which a fail occurs.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.1.1.32.1.1

atmAlarmForwardingToPort

An Index of the port that will be affected
upon the failure of the atmAlarmForwardingFailPort.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.1.1.32.1.2

atmAlarmForwardingRowStatus

Creation/Deletion of rows in the table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.12.3.1.1.32.1.3

atmAlarmForwardingFailureLevel

This parameter determines the level of failure
that will operate the Alarm Forwarding Mechanism.

Bitsr/w

.1.3.6.1.4.1.164.12.3.1.1.32.1.4

atmAlarmForwardingRecoveryMode

This parameter determines the Recovery Mode.
manual - The user should stop the RDI transmission
by using the atmAlarmForwardingRecoveryCommand.
automatic - The RDI transmission will be automatically
…

Enumerationr/w

.1.3.6.1.4.1.164.12.3.1.1.32.1.5

atmAlarmForwardingRecoveryCommand

This parameter is a command. It is applicable when
atmAlarmForwardingRecoveryMode = manual.

on - Will stop the RDI transmission. After setting to 'On'
the agent will set this parameter back to 'Off'.

Enumerationr/w

.1.3.6.1.4.1.164.12.3.1.1.32.1.6

atmAlarmForwardingTimeFilterWindow

This parameter determines the Time Filter Window, meaning:
how much time (in seconds) should the alarm exist
in order to start the Alarm Forwarding operation.

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.3.1.1.32.1.7

atmVpCrossConnectExtenTable

table

.1.3.6.1.4.1.164.12.3.1.1.34 · 1 row entry · 1 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmVpCrossConnectExtenTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmVpCrossConnectExtenTable'

An extension to the ATM VP Cross Connect table
(RFC2515 - atmVpCrossConnectTable).

atmVpCrossConnectExtenEntry row .1.3.6.1.4.1.164.12.3.1.1.34.1

An entry in the table.

Indexes

No indexes recorded

Column Syntax OID

atmVpCrossConnectName

The Connection's name.

OctetStringr/w

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.12.3.1.1.34.1.1

atmVcCrossConnectExtenTable

table

.1.3.6.1.4.1.164.12.3.1.1.35 · 1 row entry · 1 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmVcCrossConnectExtenTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmVcCrossConnectExtenTable'

An extension to the ATM VC Cross Connect table
(RFC2515 - atmVcCrossConnectTable).

atmVcCrossConnectExtenEntry row .1.3.6.1.4.1.164.12.3.1.1.35.1

An entry in the table.

Indexes

No indexes recorded

Column	Syntax	OID
atmVcCrossConnectName The Connection's name.	OctetStringr/w	`.1.3.6.1.4.1.164.12.3.1.1.35.1.1`

atmTrafficDescrParamXTable

table

.1.3.6.1.4.1.164.12.3.1.1.38 · 1 row entry · 1 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmTrafficDescrParamXTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmTrafficDescrParamXTable'

An Augment to ATM Traffic Descriptor Parameter Table
(atmTrafficDescrParamTable in ATM-MIB; RFC-2515).

atmTrafficDescrParamXEntry row .1.3.6.1.4.1.164.12.3.1.1.38.1

An entry in the table.

Indexes

No indexes recorded

Column Syntax OID

atmTrafficDescrParamMode

The Mode of the Traffic Descriptor.

Enumerationr/w

Enumerated Values:

2	up
3	down
4	llid
5	segment
6	endToEnd
7	segmentLlid
8	endToEndLlid

.1.3.6.1.4.1.164.12.3.1.1.38.1.1

atmNteIdTable

table

.1.3.6.1.4.1.164.12.3.1.2.1 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmNteIdTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmNteIdTable'

The IDs of the cards and of the system.

atmNteIdEntry row .1.3.6.1.4.1.164.12.3.1.2.1.1

Indexes

No indexes recorded

Column Syntax OID

atmNteIdIndex

An Index of the Unit ID table.
The following units have IDs in this table:
1 - System
2 - ATM Board
3 - User Card
4 - Trunk 1 card
5 - Trunk 2 card
6 - Shaper
7 - Clock Unit
8 - Slot 1 card
9 - Slot 2 card
10 - S…

SNMPv2-SMIInteger32

Enumerated Values:

2	both
4	source
5	sink

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.1.2.1.1.1

atmNteUnitId

The ID of the Unit.
For index = 6, the id will describe the validity
of a shaper in the system: 0 - Shaper Not exist
1 - Shaper exist.
For index = 7, the id will describe the validity
of a…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.1.2.1.1.2

atmNteUnitVersion

Hardware and Software version
of the module.

SNMPv2-TCDisplayString

Enumerated Values:

1	intermediate
2	segmentTermination
3	endToEndTermination

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.12.3.1.2.1.1.3

atmNteCardType

The card type.

Enumeration

Enumerated Values:

1	initial
4	source
5	sink
8	both
9	timeout
10	denied
11	conflict
12	manual

.1.3.6.1.4.1.164.12.3.1.2.1.1.4

atmNteCardStatus

Status of the card in the selected slot.

notActive - Connections are in NotReady state. No configuration is
available for the card. The access to the card HW is blocked.
…

Enumeration

Enumerated Values:

2	off
3	on

.1.3.6.1.4.1.164.12.3.1.2.1.1.5

atmNteCardCmd

Command on the card that is installed in the selected slot.
The commands are applicable according to the value of atmNteCardStatus.
See the specification document for details.

deleteConfig - Deletes the c…

Enumerationr/w

Enumerated Values:

2	disabled
3	segmentAis
4	segmentRdi
5	segmentAisAndRdi
6	endToEndAis
7	endToEndRdi
8	endToEndAisAndRdi

.1.3.6.1.4.1.164.12.3.1.2.1.1.6

atmNteProgCardType

The programmed card type.

Enumerationr/w

.1.3.6.1.4.1.164.12.3.1.2.1.1.7

atmSysIntervalTable

table

.1.3.6.1.4.1.164.12.3.1.2.8.2 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmSysIntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmSysIntervalTable'

The system level Interval table.

atmSysIntervalEntry row .1.3.6.1.4.1.164.12.3.1.2.8.2.1

Indexes

No indexes recorded

Column Syntax OID

atmSysIntervalNumber

A number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals are valid).

Integer32

Enumerated Values:

1	notConnected
2	mng
3	bridgePort
4	ds0Bundle
5	atm
6	pw

.1.3.6.1.4.1.164.12.3.1.2.8.2.1.1

atmSysIntervalCdc

Seconds in which cells dropped was occured in
15 minutes interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.3.1.2.8.2.1.2

atmNteConfIfTable

table

.1.3.6.1.4.1.164.12.3.2.1.1 · 1 row entry · 13 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmNteConfIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmNteConfIfTable'

The Physical interface configuration table.

atmNteConfIfEntry row .1.3.6.1.4.1.164.12.3.2.1.1.1

An entry in the Physical interface configuration table.
The ifIndex is of the lowest physical layer.

Indexes

No indexes recorded

Column Syntax OID

atmConfIfTransmitClk

The transmit clock of the port.

Enumerationr/w

Enumerated Values:

2	up
3	down
4	source
5	sink
6	listenToActivationCells
7	originateActivationCells

.1.3.6.1.4.1.164.12.3.2.1.1.1.1

atmConfIfLoopback

Interface Loopback.

Enumerationr/w

Enumerated Values:

2	up
3	down
4	llid
5	segment
6	endToEnd
7	segmentLlid
8	endToEndLlid

.1.3.6.1.4.1.164.12.3.2.1.1.1.2

atmConfIfFrameType

The frame type. Valid values for a 155M interface:
sonet(2), sdh(3). Valid values for a T3 interface:
direct(4), plcpInternal(5), plcpExternal(6),
directNoScrmbling(10), plcpInternalNoScrmbling(11),
plcpExternalNoScrmb…

Enumerationr/w

Constraints:
range: 2-20

.1.3.6.1.4.1.164.12.3.2.1.1.1.3

atmConfIfCardTypedeprecated

The card type.

Enumeration

.1.3.6.1.4.1.164.12.3.2.1.1.1.4

atmConfAtmIfVpiVciLimit

The limit on the sum of the VPI+VCI bits for this interface.

Enumeration

Enumerated Values:

2	both
3	none
4	source
5	sink

.1.3.6.1.4.1.164.12.3.2.1.1.1.5

atmConfIfHwFeatures

HW features command.

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.1.1.1.6

atmConfIfOutputRate

This parameter indicates the output rate in cells/sec, which is
supported per port. Successfully setting this parameter
is dependent on all other ports values calculations,
which are described in the NMS SRS.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	intermediate
2	segmentTermination
3	endToEndTermination
4	endToEndAndSegment

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.1.1.1.7

atmConfIfInputRate

This parameter indicates the input rate in cells/sec, which is
supported per port. Successfully setting this parameter
is dependent on all other ports values calculations,
which are described in the NMS SRS.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	manual
2	activator
3	listener

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.1.1.1.8

atmConfAlarmForwarding

Enables Path AIS Alarm forwarding upon a failure detection. The
following might be considered as a failure: LOS, LOF, LOC, SLM,
LOP, Path AIS and Line AIS.

disable(2) - will not forward an alarm upon a…

Enumerationr/w

Enumerated Values:

1	initial
2	up
3	down
4	source
5	sink
8	both
9	timeout
10	denied
11	conflict
12	manual

.1.3.6.1.4.1.164.12.3.2.1.1.1.9

atmConfIfAllocatedBw

Total VC Bandwidth Allocation.

SNMPv2-SMIInteger32

Enumerated Values:

2	off
3	on

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.1.1.1.10

atmConfIfLowerVpi

The Lower possible VPI.

SNMPv2-SMIInteger32r/w

Enumerated Values:

2	disabled
3	segmentAis
4	segmentRdi
5	segmentAisAndRdi
6	endToEndAis
7	endToEndRdi
8	endToEndAisAndRdi

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.1.1.1.11

atmConfIfOamMode

OAM support Mode, which determines the
interface's location in a segment wise.

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.1.1.1.12

atmConfIfOamFailureInd

This object allows user to define the type of indication
(if any) that will be created upon a LB cell failure,
for all VCs on which OAM loopback traffic is activated.
disabled(2) - no indication will be created.
…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	downStream
3	upStream

.1.3.6.1.4.1.164.12.3.2.1.1.1.13

atmNteAlarmIfTable

table

.1.3.6.1.4.1.164.12.3.2.1.2 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmNteAlarmIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmNteAlarmIfTable'

The interface Alarm table.

atmNteAlarmIfEntry row .1.3.6.1.4.1.164.12.3.2.1.2.1

An entry in the interface Alarm table.

Indexes

No indexes recorded

Column	Syntax	OID
atmInterfaceActiveAlarms A Bit String of the active alarms on this interface. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - LOS 2 - LOF 3 - Lin…	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.3.2.1.2.1.1`
atmThresholdSectionBIP When Section BIPs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.3.2.1.2.1.2`
atmThresholdLineBIP When Line BIPs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.3.2.1.2.1.3`
atmThresholdLineFEBE When Line FEBEs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.3.2.1.2.1.4`
atmThresholdPathBIP When Path BIPs are greater than this threshold, an active alarm is raised.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.3.2.1.2.1.5`
atmThresholdPathFEBE When Path FEBEs are greater than this threshold, an active alarm is raised.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.3.2.1.2.1.6`
atmThresholdErroredCells When Errored Cells are greater than this threshold, an active alarm is raised.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.3.2.1.2.1.7`
atmThresholdLostCells When Lost Cells are greater than this threshold, an active alarm is raised.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.3.2.1.2.1.8`
atmThresholdMisinsertedCells When Misinserted Cells are greater than this threshold, an active alarm is raised.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.3.2.1.2.1.9`
atmInterfaceAlarmStatus The variable is on(3) when there is any active alarm on this interface.	Enumeration	`.1.3.6.1.4.1.164.12.3.2.1.2.1.10`
atmInterfaceMaskAlarms A Bit String of alarms mask on this interface. An up bit (1) means that the respective alarm is masked. A down bit (0) means no mask. The mask is supported for the following alarms: 1 - LOS	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.3.2.1.2.1.11`

atmNteConfVpTable

table

.1.3.6.1.4.1.164.12.3.2.1.3 · 1 row entry · 15 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmNteConfVpTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmNteConfVpTable'

The ATM VP configuration table.
The table is an extension to the atmVplTable of
RFC-1695.

atmNteConfVpEntry row .1.3.6.1.4.1.164.12.3.2.1.3.1

An entry in the ATM VP configuration table.
ifIndex of the ATM layer.

Indexes

atmLoopbackVpIfIndex atmLoopbackVpVpi

Column Syntax OID

atmConfVpPolicing

Policing method desired for this VPL.

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.1.3.1.1

atmConfVpCCAdminStatus

up(2) - Activate Continuity Check (CC).
down(3) - Deactivate CC.
source(4) - Activate OAM CC(Continuity Check) of local agent
( start sending Oam cells to the remote side ).
sink(5) - Activat…

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.1.3.1.2

atmConfVpLoopbackAdminStatus

up(2) - Start loopback OAM cells.
down(3) - Stop sending loopback OAM cells.

For ace2002:
up(2) - Transmitting LB cells with llid all ones
(i.e. FFFF..FF)
down(3) - Not transmitting LB cells.…

Enumerationr/w

Enumerated Values:

1	noActive
2	inProgress
3	failed
4	endSuccessfully

.1.3.6.1.4.1.164.12.3.2.1.3.1.3

atmConfVpLoopbackSinkAddress

Destination address.
For ace101: 2 bytes are used.
For ace2002: 16 bytes are used.

OctetStringr/w

.1.3.6.1.4.1.164.12.3.2.1.3.1.4

atmConfVpCongestionControl

Each bit indicates a selection of one option
as the following description. All combinations
are possible and legal.
The codes are:
1 - EPD
2 - CLP
4 - EFCI

OctetStringr/w

.1.3.6.1.4.1.164.12.3.2.1.3.1.5

atmConfVpCCDirection

both(2) - Agent send OAM CC cells and check received OAM CC cells
source(4)- Agent send OAM CC cells.
sink(5) - Agent checks received OAM CC cells.

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.1.3.1.6

atmConfVpCreationTime

A date-time in which the VP was created.

SNMPv2-TCDateAndTime

Type Constraints:
range: 8
range: 11

Description:

A date-time specification.

field octets contents range
----- ------ -------- -----
1 1-2 year* 0..65536
2 3 month …

.1.3.6.1.4.1.164.12.3.2.1.3.1.7

atmConfVpOamSupport

OAM support mode, which determines the device location
in a segment wise.

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.1.3.1.8

atmConfVpCCOperStatus

initial(1) - The CC activation process is not started.
source(4) - Agent sends OAM CC cells.
sink(5) - Agent checks received OAM CC cells.
both (8) - OAM CC of local and remote agents activation.
timeout (9) - Timeo…

Enumeration

.1.3.6.1.4.1.164.12.3.2.1.3.1.9

atmConfVpLoopbackTraffic

This parameter has both command and status meanings:
off(2) - Set to 'Off' will Stop traffic loop. Getting this
value means that the loop is not running.
on (3) - Set to 'On' will start traffic loop. Getting
…

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.1.3.1.10

atmConfVpLoopbackFailureInd

This object allows user to define the Indication that will be created upon
a LB cell failure.
disabled(2) - no indication will be created.
segmentAis(3) - will cause Tx of a segment AIS.
segmentRdi(4) - will cause Tx o…

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.1.3.1.11

atmConfVpLoopbackFailureThreshold

The number of the LB failures before starting transmission of the
Indication defined by atmConfVcLoopbackFailureInd.
Range: 1..16. Default: 1.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.1.3.1.12

atmConfVpOamDirection

The direction of OAM cell insertion.
downStream(2) - The OAM cell will be inserted in downStream.
upStream(3) - The OAM cell will be inserted in upStream.

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.1.3.1.13

atmConfVpOamDescrIndex

This parameter indicates the VPL's OAM Descriptor index,
according to the OAM Descriptor Configuration Table.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	noActive
2	inProgress
3	failed
4	endSuccessfully

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.1.3.1.14

atmConfVpConnected

This object indicates whether this VP is connected
and if connected, what is it connected to.

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.1.3.1.15

atmNteConfVcTable

table

.1.3.6.1.4.1.164.12.3.2.1.4 · 1 row entry · 18 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmNteConfVcTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmNteConfVcTable'

The ATM VC configuration table.
The table is an extension to the atmVclTable of
RFC-2515.

atmNteConfVcEntry row .1.3.6.1.4.1.164.12.3.2.1.4.1

An entry in the ATM VC configuration table.
ifIndex of the ATM layer.

Indexes

No indexes recorded

Column Syntax OID

atmConfVcPolicing

Policing method desired for this VCL.

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.1.4.1.1

atmConfVcCCAdminStatus

up(2) - Activate Continuity Check (CC).
down(3) - Deactivate CC.
source(4) - Activate OAM CC(Continuity Check) of local agent
( start sending Oam cells to the remote side ).
sink(5) - Activate CC of r…

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.1.4.1.2

atmConfVcLoopbackAdminStatus

up(2) - Start loopback OAM cells.
down(3) - Stop sending loopback OAM cells.

For ace2002:
up(2) - Transmitting LB cells with llid all ones
(i.e. FFFF..FF)
down(3) - Not transmitting LB cells.…

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.1.4.1.3

atmConfVcLoopbackSinkAddress

Destination address.
For ace101: 2 bytes are used.
For ace2002: 16 bytes are used.

OctetStringr/w

.1.3.6.1.4.1.164.12.3.2.1.4.1.4

atmConfVcCongestionControl

Each bit indicates a selection of one option
as the following description. All combinations
are possible and legal.
The codes are:
1 - EPD
2 - CLP
4 - EFCI.
For ace2002:
1 - Packet Discard.

OctetStringr/w

.1.3.6.1.4.1.164.12.3.2.1.4.1.5

atmConfVcCCDirection

both(2) - Agent sends OAM CC cells and checks received OAM CC cells.
none(3) - Agent does not send and does not check received OAM CC cells.
source(4)- Agent sends OAM CC cells.
sink(5) - Agent checks received OAM CC …

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.1.4.1.6

atmConfVcCreationTime

A date-time in which the VC was created.

SNMPv2-TCDateAndTime

Constraints:
range: 1-96

Description:

A date-time specification.

field octets contents range
----- ------ -------- -----
1 1-2 year* 0..65536
2 3 month …

.1.3.6.1.4.1.164.12.3.2.1.4.1.7

atmConfVcOamSupport

OAM support mode, which determines the device location
in a segment wise.

endToEndAndSegment - In this mode the OAM cells are generated
before the ABM (ATM Buffer Mana…

Enumerationr/w

Enumerated Values:

1	noActive
2	inProgress
3	failed
4	endSuccessfully

.1.3.6.1.4.1.164.12.3.2.1.4.1.8

atmConfVcCCActivationCtrl

manual(1) - CC Activation process is disable
activator(2) - ACE-101 initiate CC Activation process
listener(3) - ACE-101 wait to CC Activation request from remote side.

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.1.4.1.9

atmConfVcCCOperStatus

initial (1) - The CC activation process is not started.
up (2) - Continuity Check (CC) activated.
down (3) - CC deactivated.
source (4) - OAM CC(Continuity Check) of local agent activated.
sink (5) - OAM CC of remo…

Enumeration

.1.3.6.1.4.1.164.12.3.2.1.4.1.10

atmConfVcLoopbackTraffic

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.1.4.1.11

atmConfVcLoopbackFailureInd

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.1.4.1.12

atmConfVcLoopbackFailureThreshold

The number of the LB failures before starting transmission of the
Indication defined by atmConfVcLoopbackFailureInd.
Range: 1..16. Default: 1.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.1.4.1.13

atmConfVcOamDirection

The direction of OAM cell insertion.
downStream(2) - The OAM cell will be inserted in downStream.
upStream(3) - The OAM cell will be inserted in upStream.

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.1.4.1.14

atmConfVcName

VC Name.

SNMPv2-TCDisplayStringr/w

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.12.3.2.1.4.1.15

atmConfVcConnected

This object indicates whether this VC is connected
and if connected, what is it connected to.
Originally, it was read-only.

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.1.4.1.16

atmConfVcOamDescrIndex

This parameter indicates the VCL's OAM Descriptor index,
according to the OAM Descriptor Configuration Table.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.1.4.1.17

atmConfVcNoOfUsages

This object indicates the number of times this VCL is used.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.3.2.1.4.1.18

atmNteAlarmVpTable

table

.1.3.6.1.4.1.164.12.3.2.1.5 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmNteAlarmVpTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmNteAlarmVpTable'

The ATM VP Alarm table.

atmNteAlarmVpEntry row .1.3.6.1.4.1.164.12.3.2.1.5.1

An entry in the ATM VP Alarm table.
ifIndex of the ATM layer.

Indexes

No indexes recorded

Column	Syntax	OID
atmNteVpAlarmVpi The VPI on which there is an active alarm.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.3.2.1.5.1.1`
atmNteVpActiveAlarms A Bit String of the active alarms on this VP. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - VP AIS 2 - VP Loss Of Cont…	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.3.2.1.5.1.2`

atmNteAlarmVcTable

table

.1.3.6.1.4.1.164.12.3.2.1.6 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmNteAlarmVcTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmNteAlarmVcTable'

The ATM VC Alarm table.

atmNteAlarmVcEntry row .1.3.6.1.4.1.164.12.3.2.1.6.1

An entry in the ATM VC Alarm table.
ifIndex of the ATM layer.

Indexes

No indexes recorded

Column	Syntax	OID
atmNteVcAlarmVpi The VPI of the VC on which there is an active alarm.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.3.2.1.6.1.1`
atmNteVcAlarmVci The VCI of the VC on which there is an active alarm.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.3.2.1.6.1.2`
atmNteVcActiveAlarms A Bit String of the active alarms on this VC. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - VC AIS 2 - VC Loss Of Cont…	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.3.2.1.6.1.3`

atmLoopbackVpTable

table

.1.3.6.1.4.1.164.12.3.2.2.1 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmLoopbackVpTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmLoopbackVpTable'

This table contains parameters for an OAM VP loopback test.

atmLoopbackVpEntry row .1.3.6.1.4.1.164.12.3.2.2.1.1

An entry in table atmLoopbackVpTable.

Indexes

No indexes recorded

Column Syntax OID

atmLoopbackVpIfIndex

The interface index of the ATM layer.

SNMPv2-SMIInteger32

Enumerated Values:

2	up
3	down
4	listenToActivationCells
5	originateActivationCells

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.1.1.1

atmLoopbackVpVpi

The VPI of the OAM VPL.

SNMPv2-SMIInteger32

Enumerated Values:

2	source
3	destination
4	bidirectional

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.1.1.2

atmLoopbackVpOperStatus

-noActive(1) means that the loopback test has not been activated for this VP.
-inProgress(2) means that the test has been activated and there is currently no problem.
-failed(3) means there was problem during the test o…

Enumeration

.1.3.6.1.4.1.164.12.3.2.2.1.1.3

atmLoopbackVpCDV

Cell Delay Variation for this sampling.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.1.1.4

atmLoopbackVpAverageDelay

Average delay without including lost cells.

SNMPv2-SMIInteger32

Enumerated Values:

1	off
2	fwd
3	fwdAndBwdReport

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.1.1.5

atmLoopbackVpMaxDelay

Maximum delay without including lost cells.

SNMPv2-SMIInteger32

Enumerated Values:

1	off
2	fwd
3	fwdAndBwdReport

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.1.1.6

atmLoopbackVpMinDelay

Minimum delay.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.1.1.7

atmLoopbackVpErrSessions

Errored Sessions. Will be updated once in 5 seconds.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.1.1.8

atmLoopbackVcTable

table

.1.3.6.1.4.1.164.12.3.2.2.2 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmLoopbackVcTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmLoopbackVcTable'

This table contains parameters for an OAM VC loopback test.

atmLoopbackVcEntry row .1.3.6.1.4.1.164.12.3.2.2.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

atmLoopbackVcIfIndex

The interface index of the ATM layer.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.2.1.1

atmLoopbackVcVpi

The VPI of the OAM VCL.

SNMPv2-SMIInteger32

Enumerated Values:

2	up
3	down
4	listenToActivationCells
5	originateActivationCells

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.2.1.2

atmLoopbackVcVci

The VCI of the OAM VCL.

SNMPv2-SMIInteger32

Enumerated Values:

2	source
3	destination
4	bidirectional

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.2.1.3

atmLoopbackVcOperStatus

Enumeration

.1.3.6.1.4.1.164.12.3.2.2.2.1.4

atmLoopbackVcCDV

Cell Delay Variation for this sampling.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.2.1.5

atmLoopbackVcAverageDelay

Average delay without including lost cells.

SNMPv2-SMIInteger32

Enumerated Values:

1	off
2	fwd
3	fwdAndBwdReport

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.2.1.6

atmLoopbackVcMaxDelay

The maximum delay without including lost cells.

SNMPv2-SMIInteger32

Enumerated Values:

1	off
2	fwd
3	fwdAndBwdReport

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.2.1.7

atmLoopbackVcMinDelay

The minimum delay.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.2.1.8

atmLoopbackVcErrSessions

Errored Sessions. Will be updated once in 5 seconds.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.2.1.9

atmLoopbackVpIvlTable

table

.1.3.6.1.4.1.164.12.3.2.2.3 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmLoopbackVpIvlTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmLoopbackVpIvlTable'

This table contains parameters for an OAM VP loopback test,
according interval number.

atmLoopbackVpIvlEntry row .1.3.6.1.4.1.164.12.3.2.2.3.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

atmLoopbackVpIvlIfIndex

The interface index of the ATM layer.

SNMPv2-SMIInteger32

Enumerated Values:

2	disabled
3	enabled

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.3.1.1

atmLoopbackVpIvlVpi

The VPI of the OAM VPL.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.3.1.2

atmLoopbackVpIvlIvl

The relevant interval number.

Integer32

.1.3.6.1.4.1.164.12.3.2.2.3.1.3

atmLoopbackVpIvlOperStatus

-noActive(1) means that the loopback test has not been activated for this VP during this interval.
-inProgress(2) has no meaning for an ended interval.
-failed(3) means there was problem during the test or after having …

Enumeration

.1.3.6.1.4.1.164.12.3.2.2.3.1.4

atmLoopbackVpIvlCDV

Cell Delay Variation for this interval.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.3.1.5

atmLoopbackVpIvlAverageDelay

Average delay without including lost cells for this interval.

SNMPv2-SMIInteger32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.12.3.2.2.3.1.6

atmLoopbackVpIvlMaxDelay

The maximum delay without including lost cells for this interval.

SNMPv2-SMIInteger32

Enumerated Values:

1	on
2	off
3	event

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.3.1.7

atmLoopbackVpIvlMinDelay

The minimum delay for this interval.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.3.1.8

atmLoopbackVpIvlErrSessions

Errored Sessions. Will be updated once in 5 seconds.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.3.1.9

atmLoopbackVcIvlTable

table

.1.3.6.1.4.1.164.12.3.2.2.4 · 1 row entry · 10 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmLoopbackVcIvlTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmLoopbackVcIvlTable'

This table contains parameters for an OAM VC loopback test.

atmLoopbackVcIvlEntry row .1.3.6.1.4.1.164.12.3.2.2.4.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

atmLoopbackVcIvlIfIndex

The interface index of the ATM layer.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.4.1.1

atmLoopbackVcIvlVpi

The VPI of the OAM VCL.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.4.1.2

atmLoopbackVcIvlVci

The VCI of the OAM VCL.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.4.1.3

atmLoopbackVcIvlIvl

The relevant interval number.

Integer32

Constraints:
range: 0-255

.1.3.6.1.4.1.164.12.3.2.2.4.1.4

atmLoopbackVcIvlOperStatus

-noActive(1) means that the loopback test has not been activated for this VC during this interval.
-inProgress(2) has no meaning per interval.
-failed(3) means there was problem for this test during this interval.
-endS…

Enumeration

.1.3.6.1.4.1.164.12.3.2.2.4.1.5

atmLoopbackVcIvlCDV

Cell Delay Variation for this interval.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.4.1.6

atmLoopbackVcIvlAverageDelay

Average delay without including lost cells.

SNMPv2-SMIInteger32

Enumerated Values:

1	frameRelay
2	atmDxi
3	bridgedEthernet
4	smdsDxi
5	aal1Stream
6	routedEthernet
7	satop
8	tdmoIp
9	frDlci
10	hdlc
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.4.1.7

atmLoopbackVcIvlMaxDelay

The maximum delay without including lost cells.

SNMPv2-SMIInteger32

Enumerated Values:

1	r64KBps
2	r128KBps
3	r192KBps
4	r256KBps
5	r320KBps
6	r384KBps
7	r448KBps
8	r512KBps
9	r576KBps
10	r640KBps
11	r704KBps
12	r768KBps
13	r832KBps
14	r896KBps
15	r960KBps
16	r1024KBps
17	r1088KBps
18	r1152KBps
19	r1216KBps
20	r1280KBps
21	r1344KBps
22	r1408KBps
23	r1472KBps
24	r1536KBps
25	r1544network
26	r1600KBps
27	r1664KBps
28	r1728KBps
29	r1792KBps
30	r1856KBps
31	r1920KBps
32	r1984KBps
33	r2048KBps
34	r2048network
35	r8192KBps
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.4.1.8

atmLoopbackVcIvlMinDelay

The minimum delay.

SNMPv2-SMIInteger32

Enumerated Values:

1	off
2	on
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.4.1.9

atmLoopbackVcIvlErrSessions

Errored Sessions. Will be updated once in 5 seconds.

SNMPv2-SMIInteger32

Enumerated Values:

1	nrzi
2	nrz
255	notApplicable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.2.4.1.10

atmVpPmTable

table

.1.3.6.1.4.1.164.12.3.2.3.1 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmVpPmTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmVpPmTable'

This table contains parameters for VP performance monitoring.

atmVpPmEntry row .1.3.6.1.4.1.164.12.3.2.3.1.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

atmVpPmIfIndex

The interface index of the ATM layer.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.3.1.1.1

atmVpPmVpi

The VPI of the Performance Monitoring VPL.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.3.1.1.2

atmVpPmAdminStatus

up(2) - Activate PM.
down(3) - Deactivate PM.
listenToActivationCells(4) - .
originateActivationCells(5) - .

Enumerationr/w

Constraints:
range: 0-255

.1.3.6.1.4.1.164.12.3.2.3.1.1.3

atmVpPmDirection

The direction of PM.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	x21
3	v35
4	v36
5	rs530
6	rs232

.1.3.6.1.4.1.164.12.3.2.3.1.1.4

atmVpPmBlockSize

Valid block sizes (in cells): 128, 256, 512, 1024, 2048, 4096,
8192, 16384, 32768.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	normal
3	inverted

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.3.1.1.5

atmVpPmRowStatus

Creation/Deletion of rows in the table.

SNMPv2-TCRowStatusr/w

Enumerated Values:

1	notApplicable
2	off
3	on

Description:

.1.3.6.1.4.1.164.12.3.2.3.1.1.6

atmVpPmSink

off (1) - Deactivate PM.
fwd (2) - Activate Forward PM only.
fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	off
3	on

.1.3.6.1.4.1.164.12.3.2.3.1.1.7

atmVpPmSource

off (1) - Deactivate PM.
fwd (2) - Activate Forward PM only.
fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.3.1.1.8

atmVcPmTable

table

.1.3.6.1.4.1.164.12.3.2.3.2 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmVcPmTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmVcPmTable'

This table contains parameters for VC performance monitoring.

atmVcPmEntry row .1.3.6.1.4.1.164.12.3.2.3.2.1

An entry in table.

Indexes

No indexes recorded

Column Syntax OID

atmVcPmIfIndex

The interface index of the ATM layer.

SNMPv2-SMIInteger32

Enumerated Values:

1	txGain0db
2	txGain7dot5db
3	txGain15db
4	txGain22dot5db
5	len0p133ft
6	len133p266ft
7	len266p399ft
8	len399p533ft
9	len533p655ft
10	unbalanceE1
11	balanceE1

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.3.2.1.1

atmVcPmVpi

The VPI of the Performance Monitoring VCL.

SNMPv2-SMIInteger32

Enumerated Values:

1	ccittE1
2	restoreT1secFast
3	restoreT10sec62411

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.3.2.1.2

atmVcPmVci

The VCI of the PM VCL.

SNMPv2-SMIInteger32

Enumerated Values:

2	off
4	dedicatedTs
6	dedicatedFr

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.3.2.1.3

atmVcPmAdminStatus

up(2) - Activate PM.
down(3) - Deactivate PM.
listenToActivationCells(4) - .
originateActivationCells(5) - .

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.3.2.1.4

atmVcPmDirection

The direction of PM.

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.3.2.1.5

atmVcPmBlockSize

Valid block sizes (in cells): 128, 256, 512, 1024, 2048, 4096,
8192, 16384, 32768.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.3.2.3.2.1.6

atmVcPmRowStatus

Creation/Deletion of rows in the table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.12.3.2.3.2.1.7

atmVcPmSink

off (1) - Deactivate PM.
fwd (2) - Activate Forward PM only.
fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.3.2.1.8

atmVcPmSource

off (1) - Deactivate PM.
fwd (2) - Activate Forward PM only.
fwdAndBwdReport(3) - Activate Forward PM and Backward reporting.

Enumerationr/w

.1.3.6.1.4.1.164.12.3.2.3.2.1.9

atmNteMdlConfigTable

table

.1.3.6.1.4.1.164.12.3.3.1.1 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmNteMdlConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmNteMdlConfigTable'

Module configuration table.

atmNteMdlConfigEntry row .1.3.6.1.4.1.164.12.3.3.1.1.1

There is an entry in this table just for those modules that have
parameters that are relevant to module level only.

Indexes

No indexes recorded

Column Syntax OID

atmNteMdlSlotIndex

The slot number.

Integer32

Enumerated Values:

1	msec100
2	msec200
3	msec500
4	msec1000
5	msec1500
6	msec2000

.1.3.6.1.4.1.164.12.3.3.1.1.1.1

atmNteMdlPrtCpuSharing

This object lets the user decide what will be the CPU sharing
between the ports of the module. This object is applicable for
modules in which the same CPU handles the traffic of all ports.

equal - All p…

Enumerationr/w

.1.3.6.1.4.1.164.12.3.3.1.1.1.2

atmNteMdlInputPriorityMechanism

This object allows the user to Enable/Disable the Input priority mechanism.
This object is applicable for modules with more than one port, in which the
total ports input may be greater than the port output.
…

Enumerationr/w

.1.3.6.1.4.1.164.12.3.3.1.1.1.3

atmSuSystemHistoryAlrTable

table

.1.3.6.1.4.1.164.12.4.1.3 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmSuSystemHistoryAlrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmSuSystemHistoryAlrTable'

buffer contain history buffer of agent alarms.

atmSuSystemHistoryAlrEntry row .1.3.6.1.4.1.164.12.4.1.3.1

Agent alarm history list entry.

Indexes

No indexes recorded

Column Syntax OID

atmSuSystemHistoryAlrIndex

A unique number to identify an entry in the history alarm table.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.1.3.1.1

atmSuSystemHistoryAlrIfIndex

This value indicates the port on which the alarms occured.
configuration(system) alarms have port index equal to 0.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.1.3.1.2

atmSuSystemHistoryAlrDescription

This attribute is a text description of the alarm.
The alarm descipion include alarm code and alarm text.

OctetString

Enumerated Values:

1	active
2	notActive

.1.3.6.1.4.1.164.12.4.1.3.1.3

atmSuSystemHistoryAlrStatus

This attribute indicates the status of the alarm.

Enumeration

Enumerated Values:

1	active
2	notActive

.1.3.6.1.4.1.164.12.4.1.3.1.4

atmSuSystemHistoryAlrOccurrenceTime

This value indicates the date and time of the occurrence
of the event that caused this alarm.
Date and time format: YYYY-MM-DD, HH:MM:SS

SNMPv2-TCDisplayString

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.164.12.4.1.3.1.5

atmSuSystemHistoryAlrVpi

This value indicates the ATM VPI of the connection
associated with the event that caused this alarm.
When not applicable, value is 0

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.1.3.1.6

atmSuSystemHistoryAlrVci

This value indicates the ATM VCI of the connection
associated with with the event that caused this alarm.
When not applicable, value is 0

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	sw
3	hwNcits1
4	hwNcits2

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.1.3.1.7

atmSuSystemCurrentAlrTable

table

.1.3.6.1.4.1.164.12.4.1.5 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmSuSystemCurrentAlrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmSuSystemCurrentAlrTable'

table which contains all alarms Currently active ( status ON )
in the agent.

atmSuSystemCurrentAlrEntry row .1.3.6.1.4.1.164.12.4.1.5.1

Agent alarm list entry.

Indexes

No indexes recorded

Column	Syntax	OID
atmSuSystemCurrentAlrIndex A unique number to identify an entry in the Current alarms table.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.4.1.5.1.1`
atmSuSystemCurrentAlrIfIndex This value indicates the port on which the alarms occured. configuration alarms have port index equal to 0.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.4.1.5.1.2`
atmSuSystemCurrentAlrDescription This attribute is a text description of the alarm. The alarm descipion include alarm code and alarm text.	OctetString	`.1.3.6.1.4.1.164.12.4.1.5.1.3`

atmSuPortDataCnfgTable

table

.1.3.6.1.4.1.164.12.4.2.1 · 1 row entry · 13 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmSuPortDataCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmSuPortDataCnfgTable'

Data Port global configuration table.
this table include parametes which are common to the physical port
and not depend on whether the port interface is Frame-Relay or
ATM-DXI.

atmSuPortDataCnfgEntry row .1.3.6.1.4.1.164.12.4.2.1.1

the entries at this table describes the configuration
of the Data-Port.

Indexes

No indexes recorded

Column	Syntax	OID
atmSuPortDataApplication This attribute indicates the protocol application which runs above the physical port.	Enumerationr/w	`.1.3.6.1.4.1.164.12.4.2.1.1.1`
atmSuPortDataRate This attribute indicates the operation rate of the port. AmcdT1 / Ace-20T allowes rates up to 1536KBps ( options 1-12 ), while AmcdE1 / Ace-20E allowes all options.	Enumerationr/w	`.1.3.6.1.4.1.164.12.4.2.1.1.2`
atmSuPortDataDCD This attribute indicates if the bits CtsCd( Clear-to-send Carry-detect) are being checked. In AMCD CTS is also checked. off - ignore DCD signal on - obey DCD signal	Enumerationr/w	`.1.3.6.1.4.1.164.12.4.2.1.1.3`
atmSuPortDataModedeprecated This attribute indicates the port mode of sampling data physical.	Enumeration	`.1.3.6.1.4.1.164.12.4.2.1.1.4`
atmSuPortDataCRC This attribute indicates the type of CRC checking on receiving/transmiting frames.	Enumerationr/w	`.1.3.6.1.4.1.164.12.4.2.1.1.5`
atmSuPortDataClock This attribute indicates the clock using for synchronization for the data port.	Enumerationr/w	`.1.3.6.1.4.1.164.12.4.2.1.1.6`
atmSuPortDataMaxNoOfConns this object indicates the maximum number of cross-connect connections allowed beetween the ATM port and the Data Port identified by IfIndex.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.4.2.1.1.7`
atmSuPortDataConfNoOfConns this object indicates the configured number of cross-connect connections exist beetween the ATM port and the Data Port identified by IfIndex.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.4.2.1.1.8`
atmSuPortDataIdleCode This attribute is applicable only for application aal1Stream. It indicates the value to be transmitted whenever the port is idle.	Integer32r/w	`.1.3.6.1.4.1.164.12.4.2.1.1.9`
atmSuPortDataInterfaceType Physical layer interface type. (Configureable or Non-Configureable)	Enumerationr/w	`.1.3.6.1.4.1.164.12.4.2.1.1.10`
atmSuPortDataClkPolarity This object indicates the clock polarity. For LA-110/140 this object will be applicable only for X.21/V.35/data port	Enumerationr/w	`.1.3.6.1.4.1.164.12.4.2.1.1.11`
atmSuPortDataCtsStatus CTS status - the signal state received from ATM network (for the local DTE usage). LA110 receiving RTS down from remote DTE device via ATM network, will change CTS signal state to down (off) toward local DTE device	Enumeration	`.1.3.6.1.4.1.164.12.4.2.1.1.12`
atmSuPortDataRtsStatus RTS status - the signal state received from local DTE (to be forwarded to ATM network). LA110 receiving RTS down from the local DTE device will transmit all '1' to ATM (in order to carry the signaling to re…	Enumeration	`.1.3.6.1.4.1.164.12.4.2.1.1.13`

atmSuPortDs1CnfgTable

table

.1.3.6.1.4.1.164.12.4.2.2.1 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmSuPortDs1CnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmSuPortDs1CnfgTable'

This table include expansion configuration to the DS1 physical port.

atmSuPortDs1CnfgEntry row .1.3.6.1.4.1.164.12.4.2.2.1.1

the entries at this table describes the configuration
of the agent physical.

Indexes

No indexes recorded

Column	Syntax	OID
atmSuPortDs1CnfgRxSensitivity This attribute is the rx line sensetivity parameter used only for T1/CSU and E1/LTU interfaces.	Enumerationr/w	`.1.3.6.1.4.1.164.12.4.2.2.1.1.1`
atmSuPortDs1CnfgLBO This attribute is the line-Build-Out indicates sensitivity of the DS1 interface. The user can define if the agent will be CSU or DSU (for T1 only) by choosing the right option. On E1 interface this is done by hardware, …	Enumerationr/w	`.1.3.6.1.4.1.164.12.4.2.2.1.1.2`
atmSuPortDs1CnfgRestoreTime Determines the time passing from the disappearance of the loss of synchronization condition (red alarm) to the restoration of normal service. The options 1secFast(2) and 10sec62411(3) for E1 interfaces are proprietary i…	Enumerationr/w	`.1.3.6.1.4.1.164.12.4.2.2.1.1.3`
atmSuPortDs1CnfgInbandMng A unique number to identify type of inband management over the link. For LA-104 and IMXi4, only one port may be used for inband management	Enumerationr/w	`.1.3.6.1.4.1.164.12.4.2.2.1.1.4`
atmSuPortDs1CnfgDedicatedTs A unique number to identify Dedicated Time Slot for inband management of the T1/E1 port. It is applicable only when atmSuPortDs1CnfgInbandMng selected is not off. 1..24 - Dedicated TS of T1 1..31 - Dedi…	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.4.2.2.1.1.5`

atmSuPortDs1CbrCnfgTable

table

.1.3.6.1.4.1.164.12.4.2.2.2 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmSuPortDs1CbrCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmSuPortDs1CbrCnfgTable'

This table include expansion configuration to the DS1 physical port.

atmSuPortDs1CbrCnfgEntry row .1.3.6.1.4.1.164.12.4.2.2.2.1

the entries at this table describes the configuration
of the agent physical.

Indexes

No indexes recorded

Column	Syntax	OID
atmSuPortDs1CbrIdleCode An Idle code which sent on unused time-slots at CBR port .	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.4.2.2.2.1.1`
atmSuPortDs1CbrRxTimeSlots This value indicates the time-slots used by the port for receiving. It uses 32 bits ( in 4 bytes octet string ) for E1 and low 24 bits for T1. each bit represents a time slot for receiving : time-slot 0 = bit 0 (LSB - …	TimeSlots	`.1.3.6.1.4.1.164.12.4.2.2.2.1.2`
atmSuPortDs1CbrTxTimeSlots This value indicates the time-slots used by the port for transmiting. It uses 32 bits for E1 and low 24 bits for T1. each bit represents a time slot for transmiting : time-slot 0 = bit 0 (LSB - most right bit in last b…	TimeSlots	`.1.3.6.1.4.1.164.12.4.2.2.2.1.3`
atmSuPortDs1CbrMaxNoOfConns this object indicates the maximum number of cross-connect connections allowed beetween the ATM port and the CBR Port identified by IfIndex.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.4.2.2.2.1.4`
atmSuPortDs1CbrConfNoOfConns this object indicates the configured number of cross-connect connections exist beetween the ATM port and the CBR Port identified by IfIndex.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.4.2.2.2.1.5`
atmSuPortDs1CbrSignallingSampleTime determines how often the signalling of the DBCES connections are sampled and thier activity determined.	Enumerationr/w	`.1.3.6.1.4.1.164.12.4.2.2.2.1.6`

atmSuPortAtmCnfgTable

table

.1.3.6.1.4.1.164.12.4.2.3.1 · 1 row entry · 11 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmSuPortAtmCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmSuPortAtmCnfgTable'

This table contains global configuration to the ATM port.

atmSuPortAtmCnfgEntry row .1.3.6.1.4.1.164.12.4.2.3.1.1

This object contains information about agent ATM configuration.

Indexes

No indexes recorded

Column Syntax OID

atmSuPortAtmCnfgIdleCellCLP

Determines the clp bit value for transmition
in empty time slots.

Enumerationr/w

Enumerated Values:

1	active
2	notActive

.1.3.6.1.4.1.164.12.4.2.3.1.1.1

atmSuPortAtmCnfgScramble

Determined by the standards if the cell will be scrambled or not.

Enumerationr/w

Enumerated Values:

1	none
2	ccittQ933A
3	ansiT1617D
4	lmi

.1.3.6.1.4.1.164.12.4.2.3.1.1.2

atmSuPortAtmSNMPVpi

The Vcc Vpi for SNMP requests.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	u2nnet
3	u2nuser
4	bidirect

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.2.3.1.1.3

atmSuPortAtmSNMPVci

The Vcc Vci for SNMP requests.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	active
2	notActive

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.2.3.1.1.4

atmSuPortAtmSNMPStatus

value indicates if the SNMP Vcc is available for management.

Enumerationr/w

.1.3.6.1.4.1.164.12.4.2.3.1.1.5

atmSuPortAtmILMIStatus

Value indicates if agent should respond to ILMI requests from the
Atm switch or forward it.
note: when using Atm to Frame-Relay configuration this value should be
active to support ILMI.
when using Atm-AtmDx…

Enumerationr/w

.1.3.6.1.4.1.164.12.4.2.3.1.1.6

atmSuPortAtmSNMPIp

The interface IP address for SNMP requests.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.12.4.2.3.1.1.7

atmSuPortAtmCnfgCDVOptimization

value indicates if optimization of CDV (Cell Delay Varation)
is enbabled.

Enumerationr/w

.1.3.6.1.4.1.164.12.4.2.3.1.1.8

atmSuPortAtmCnfgShapingMode

ATM Shaping mode.
Three possible values:
SW Shaping.
HW Shaping - APC with NCITS = 1.
HW Shaping - APC with NCITS = 2
The difference between the two hardware modes
is in the connection cell granula…

Enumerationr/w

.1.3.6.1.4.1.164.12.4.2.3.1.1.9

atmSuPortAtmSNMPTrafficDescrIndex

The value of this object identifies the row
in the atmTrafficDescrParamTable which
applies to the transmit direction of the VCL.

ATM-TC-MIBAtmTrafficDescrParamIndexr/w

Type Constraints:
range: 0..2147483647

.1.3.6.1.4.1.164.12.4.2.3.1.1.10

atmSuPortAtmTrafficDescrIndex

The value of this object identifies the row
in the atmTrafficDescrParamTable which
applies to whole ATM WAN port.

ATM-TC-MIBAtmTrafficDescrParamIndexr/w

Type Constraints:
range: 0..2147483647

.1.3.6.1.4.1.164.12.4.2.3.1.1.11

atmSuPortAtmIfStatsTable

table

.1.3.6.1.4.1.164.12.4.2.3.2 · 1 row entry · 8 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmSuPortAtmIfStatsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmSuPortAtmIfStatsTable'

The table contains additional statistics information about
the ATM interface.

atmSuPortAtmIfStatsEntry row .1.3.6.1.4.1.164.12.4.2.3.2.1

An entry in the ATM Interface statistics table.

Indexes

No indexes recorded

Column Syntax OID

atmSuPortAtmRxClp0Cells

The number of cells received with correct
HECs and CLP=0 and not misrouted

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.2.1.1

atmSuPortAtmRxClp1Cells

The number of cells received with correct
HEC's and CLP=1 and not misrouted.

SNMPv2-SMICounter32

Enumerated Values:

1	mode1a
2	mode1b
3	mode2

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.2.1.2

atmSuPortAtmRxEfciSetCells

The number of cells received with EFCI bit set by
the Agent

SNMPv2-SMICounter32

Enumerated Values:

1	none
2	lmi

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.2.1.3

atmSuPortAtmRxOamCells

The number of OAM cells received with correct HECs.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.2.1.4

atmSuPortAtmTxClp0Cells

The number of cells transmitted with CLP=0.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.2.1.5

atmSuPortAtmTxClp1Cells

The number of cells transmitted with CLP=1.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.2.1.6

atmSuPortAtmTxEfciSetCells

The number of cells transmitted with EFCI bit set by
the Agent

SNMPv2-SMICounter32

Enumerated Values:

1	off
2	on

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.2.1.7

atmSuPortAtmTxOamCells

The number of transmitted OAM cells.

SNMPv2-SMICounter32

Enumerated Values:

1	off
2	on

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.2.1.8

atmSuPortAtmVclStatsTable

table

.1.3.6.1.4.1.164.12.4.2.3.3 · 1 row entry · 20 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmSuPortAtmVclStatsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmSuPortAtmVclStatsTable'

The table contains additional information about
the ATM Vcl end points.

atmSuPortAtmVclStatsEntry row .1.3.6.1.4.1.164.12.4.2.3.3.1

An entry in the ATM Vcl statistics table.
For Vpl statistics, use atmVclVci = 65536
(maximum valid value of atmVclVci +1)

Indexes

IF-MIBifIndex

Column Syntax OID

atmSuPortAtmVclStatsRxCells

The total number of cells received with
correct HEC's.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.3.1.1

atmSuPortAtmVclStatsRxClp0Cells

The number of cells received with correct
HEC's and CLP=0.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.3.1.2

atmSuPortAtmVclStatsRxClp1Cells

The number of cells received with correct
HEC's and CLP=1.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.3.1.3

atmSuPortAtmVclStatsRxDiscardsCells

The number of cells, in ingress direction,
discarded due to policing violation.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.3.1.4

atmSuPortAtmVclStatsTxCells

The total number of cells transmitted.

SNMPv2-SMICounter32

Enumerated Values:

1	active
2	notActive
255	notApplicable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.3.1.5

atmSuPortAtmVclStatsTxClp0Cells

The number of cells transmitted with CLP=0.

SNMPv2-SMICounter32

Enumerated Values:

1	active
2	notActive
255	notApplicable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.3.1.6

atmSuPortAtmVclStatsTxClp1Cells

The number of cells transmitted with CLP=1.

SNMPv2-SMICounter32

Enumerated Values:

2	no
3	yes
255	notApplicable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.3.1.7

atmSuPortAtmVclStatsRxTotalAISCells

Total number of AIS cells received on the VC.

SNMPv2-SMICounter32

Enumerated Values:

1	rip1
2	rip2
3	rip1And2
4	none
255	notApplicable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.3.1.8

atmSuPortAtmVclStatsRxTotalCCCells

Total number of Continuity Check cells that were
received on the VC.

SNMPv2-SMICounter32

Enumerated Values:

1	accessOnly
2	accessAndSwitching
255	notApplicable

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.3.1.9

atmSuPortAtmVclStatsTotalSuccLoopbacks

Total number of loopbacks that were requested by the ACE20
and for which there was a response (not supported).

SNMPv2-SMICounter32

Constraints:
range: 0-10

.1.3.6.1.4.1.164.12.4.2.3.3.1.10

atmSuPortAtmVclStatsTotalFailLoopbacks

Total number of loopbacks that were requested by the ACE20
and for which there was no response (not supported).

SNMPv2-SMICounter32

Constraints:
range: 0-1000000

.1.3.6.1.4.1.164.12.4.2.3.3.1.11

atmSuPortAtmVclStatsRxTotalRDICells

Total number of RDI cells received on a VC.

SNMPv2-SMICounter32

Enumerated Values:

1	notApplicable
2	off
3	on

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.3.1.12

atmSuPortAtmVclStatsTotalLOCSeconds

Total number of seconds during which there was loss of
continuity on the VC - no data and no continuity check cells
were received on the VC whilst it was in 'sink' continuity
check mode.

SNMPv2-SMICounter32

Enumerated Values:

1	active
4	createAndGo
6	destroy

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.3.1.13

atmSuPortAtmVclStatsRxTotalLoopbackRequests

Total number of loopback requests received by the ACE20 on a VC.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.3.1.14

atmSuPortAtmVclStatsTxTotalAISCells

Total number of AIS cells that were transmitted on a VC.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.3.1.15

atmSuPortAtmVclStatsTxTotalCCCells

Total number of continuity check cells that were transmitted on
a VC (when there is no data cells and the connection is in
'source' continuity check mode).

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.3.1.16

atmSuPortAtmVclStatsTxTotalRDICells

Total number of RDI cells transmitted on a VC.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.3.1.17

atmSuPortAtmVclStatsTxTotalLoopbackResponses

Total number of loopback responses that were transmitted as a
result of loopback requests received.

SNMPv2-SMICounter32

Enumerated Values:

1	convSscs
2	conv
3	always0
4	always1

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.3.1.18

atmSuPortAtmVclStatsTxTotalLoopbackRequests

Total number of loopback requests that were transmitted by the ACE20 on a VC.

SNMPv2-SMICounter32

Enumerated Values:

1	conv
2	always0
3	always1

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.3.1.19

atmSuPortAtmVclStatsRxTotalLoopbackResponses

Total number of loopback responses that were received as a
result of loopback transmitted by the ACE20.

SNMPv2-SMICounter32

Enumerated Values:

1	conv
2	always0

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.3.3.1.20

atmSuPortFrLportTable

table

.1.3.6.1.4.1.164.12.4.2.4.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmSuPortFrLportTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmSuPortFrLportTable'

The table Contains configuration parameters of the Frame-Relay
port and has expansion to  frLportTable in RFC1604 MIB.

atmSuPortFrLportEntry row .1.3.6.1.4.1.164.12.4.2.4.1.1

An entry in the Frame Relay Logical Port
Information table.

Indexes

No indexes recorded

Column	Syntax	OID
atmSuPortFrLportSNMPDlci The SNMP Dlci of this entry.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.4.2.4.1.1.1`
atmSuPortFrLportSNMPStatus value indicates if SNMP over FR is available for management.	Enumerationr/w	`.1.3.6.1.4.1.164.12.4.2.4.1.1.2`
atmSuPortFrLportVCSigProtocol The value of this object identifies the Local In-Channel Signaling Protocol that is used for this frame relay UNI/NNI logical port.	Enumerationr/w	`.1.3.6.1.4.1.164.12.4.2.4.1.1.3`
atmSuPortFrLportVCSigProcedure The value of this object identifies the Local In-Channel Signaling Procedure that is used for this UNI/NNI logical port. The UNI/NNI logical port can be performing user-to-network network-side and user-to-network user-…	Enumerationr/w	`.1.3.6.1.4.1.164.12.4.2.4.1.1.4`
atmSuPortFrLportCLLM indicate if the configuration is supporting CLLM ( Consolidated Link Layer Management ) .	Enumerationr/w Constraints: `range: 1-4095`	`.1.3.6.1.4.1.164.12.4.2.4.1.1.5`
atmSuPortFrLportSNMPIp The interface IP address of this entry.	RFC1155-SMIIpAddressr/w Constraints: `range: 0-65535`	`.1.3.6.1.4.1.164.12.4.2.4.1.1.6`

atmSuPortFrPvcEndptTable

table

.1.3.6.1.4.1.164.12.4.2.4.2 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmSuPortFrPvcEndptTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmSuPortFrPvcEndptTable'

The table contains additional information about
the Frame Relay end point.

atmSuPortFrPvcEndptEntry row .1.3.6.1.4.1.164.12.4.2.4.2.1

An entry for FR end-point statistics ( expansion to RFC 1604 ).

Indexes

No indexes recorded

Column Syntax OID

atmSuPortFrPvcEndptTxFECNs

number of frames transmited with FECN ( Forward Explicit
Congestion Notification ).

SNMPv2-SMICounter32

Enumerated Values:

1	up
2	down

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.4.2.1.1

atmSuPortFrPvcEndptTxBECNs

number of frames transmited with BECN ( Backward Explicit
Congestion Notification ).

SNMPv2-SMICounter32

Enumerated Values:

1	up
2	down

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.4.2.1.2

atmSuPortFrPvcEndptTxDEs

number of frames transmited with the DE ( Discarded Eligible ) bit set.

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.4.2.1.3

atmSuPortFrPvcEndptRxFECNs

number of frames received with FECN ( Forward Explicit
Congestion Notification ).

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.4.2.1.4

atmSuPortFrPvcEndptRxBECNs

number of frames received with BECN ( Backward Explicit
Congestion Notification ).

SNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.4.2.4.2.1.5

atmSuPortDxiConfTable

table

.1.3.6.1.4.1.164.12.4.2.5.1 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmSuPortDxiConfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmSuPortDxiConfTable'

This table contains ATM-DXI managment
address (DFA) ending at the local agent.
only LMI managment supported for ATM-DXI.

atmSuPortDxiConfEntry row .1.3.6.1.4.1.164.12.4.2.5.1.1

This object contains information about agent Dxi interface.

Indexes

No indexes recorded

Column	Syntax	OID
atmSuPortDxiPortMode This object identifies the dxi mode being used by the atm dxi port.	Enumerationr/w	`.1.3.6.1.4.1.164.12.4.2.5.1.1.1`
atmSuPortDxiSigProtocol This value indicates if we using LMI signalling protocol or not using any signalling .	Enumerationr/w Constraints: `range: 10-217`	`.1.3.6.1.4.1.164.12.4.2.5.1.1.2`
atmSuPortDxiSigDfa The Signalling Dfa address . the default LMI Dfa defined for LMI by the AtmForum is 0.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.4.2.5.1.1.3`

atmSuPortCmdTable

table

.1.3.6.1.4.1.164.12.4.2.6 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmSuPortCmdTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmSuPortCmdTable'

General commands to be done on agent's ports.

atmSuPortCmdEntry row .1.3.6.1.4.1.164.12.4.2.6.1

This object contains entry information.

Indexes

No indexes recorded

Column	Syntax	OID
atmSuResetPortStatsCmd reset statistics of port.	Enumerationr/w	`.1.3.6.1.4.1.164.12.4.2.6.1.1`
atmSuResetConnsStatsCmd reset statistics of all cross connections attached to this port. set-request is allowed only on the DATA Ports . for get-request value is always 'off'	Enumerationr/w Constraints: `range: 1-4095`	`.1.3.6.1.4.1.164.12.4.2.6.1.2`

atmSuPortEtherTable

table

.1.3.6.1.4.1.164.12.4.2.7.1 · 1 row entry · 13 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmSuPortEtherTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmSuPortEtherTable'

The table Contains configuration parameters of the Ethernet port.

atmSuPortEtherEntry row .1.3.6.1.4.1.164.12.4.2.7.1.1

An entry in the Ethernet Port Information table.

Indexes

No indexes recorded

Column Syntax OID

atmSuPortEtherIP

The interface IP address for SNMP requests.

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.12.4.2.7.1.1.1

atmSuPortEtherMask

The interface IP address mask for SNMP requests.

RFC1155-SMIIpAddressr/w

Enumerated Values:

1	up
2	down

Type Constraints:
range: 4

.1.3.6.1.4.1.164.12.4.2.7.1.1.2

atmSuPortEtherDefaultGateWayIp

The Ethernet bridge default gateway IP address.

RFC1155-SMIIpAddressr/w

Enumerated Values:

1	up
2	down

Type Constraints:
range: 4

.1.3.6.1.4.1.164.12.4.2.7.1.1.3

atmSuPortEtherDefaultCrossConnectId

Default Cross Connect Id.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.2.7.1.1.4

atmSuPortEtherDefaultGatewayStatus

Default Gateway Status.

Enumerationr/w

.1.3.6.1.4.1.164.12.4.2.7.1.1.5

atmSuPortEtherSNMPStatus

The value indicates if the SNMP of Ethernet bridge interface is available
for management.

Enumerationr/w

Enumerated Values:

1	highPriority
2	mediumPriority
3	lowPriority

.1.3.6.1.4.1.164.12.4.2.7.1.1.6

atmSuPortEtherFragmentation

Fragmentation. When application is not router value must be 'notApplicable'.

Enumerationr/w

.1.3.6.1.4.1.164.12.4.2.7.1.1.7

atmSuPortEtherRIPMode

RIP Mode. When application is not router value must be 'notApplicable'.

Enumerationr/w

.1.3.6.1.4.1.164.12.4.2.7.1.1.8

atmSuPortEtherBridgingMode

Bridging mode can be one of the following:
ATM <> Ethernet - Bridging is between the Ethernet
port and the ATM port (there is no bridging between VCs).
ATM <> Ethernet + ATM - Bridging is done both between
the Ethern…

Enumerationr/w

.1.3.6.1.4.1.164.12.4.2.7.1.1.9

atmSuPortEtherARPTimeout

ARP Timeout. When application is not router or when
this object is not applicable, value must be 0.

Integer32r/w

.1.3.6.1.4.1.164.12.4.2.7.1.1.10

atmSuPortEtherAgingTime

The timeout period in seconds for aging out stored information.
valid values are 10...1000000. The value of (0) has
the special meaning - not applicable.

Integer32r/w

Constraints:
range: 1-4095

.1.3.6.1.4.1.164.12.4.2.7.1.1.11

atmSuPortEtherPppOEEnable

Enable or Disable transparent PPP over ethernet bridge.
When PPP over Ethernet is enabled, non PPP traffic is
blocked by the bridge.

Enumerationr/w

Constraints:
range: 0-65535

.1.3.6.1.4.1.164.12.4.2.7.1.1.12

atmSuPortEtherStatus

This object allows user to add/remove entries to/from this table.
It will be supported only by certain devices.
destroy - may not be possible for certain interfaces.

Enumerationr/w

.1.3.6.1.4.1.164.12.4.2.7.1.1.13

atmFrDescrTable

table

.1.3.6.1.4.1.164.12.4.3.1.2 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmFrDescrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmFrDescrTable'

This table contains information on ATM to FR Connection
descriptor types, and their associated parameters.

atmFrDescrEntry row .1.3.6.1.4.1.164.12.4.3.1.2.1

This list contains ATM to FR Connection descriptor
type, and its associated parameters.

Indexes

No indexes recorded

Column Syntax OID

atmFrDescrIndex

This object is used to identify the row index of
the ATM to FR connection descriptor table.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.3.1.2.1.1

atmFrDescrType

The value of this object identifies the type
of the ATM to FR Connection descriptor.
The type may indicate Network connection descriptor
or a Service connection descriptor with one or more
parameters.
These parameters a…

ObjectIdentifierr/w

Enumerated Values:

1	off
2	on

.1.3.6.1.4.1.164.12.4.3.1.2.1.2

atmFrDescrClp2De

The first parameter of the ATM to FR Connection
descriptor used according to the value of atmFrDescrType.

Enumerationr/w

.1.3.6.1.4.1.164.12.4.3.1.2.1.3

atmFrDescrDe2Clp

The second parameter of the ATM to FR Connection
descriptor used according to the value of atmFrDescrType.

Enumerationr/w

.1.3.6.1.4.1.164.12.4.3.1.2.1.4

atmFrDescrFecn2Efci

The third parameter of the ATM to FR Connection
descriptor used according to the value of atmFrDescrType.

Enumerationr/w

.1.3.6.1.4.1.164.12.4.3.1.2.1.5

atmFrDescrMappingMode

The fourth parameter of the ATM to FR Connection
descriptor used according to the value of atmFrDescrType.

Enumerationr/w

.1.3.6.1.4.1.164.12.4.3.1.2.1.6

atmFrDescrRowStatus

This object is used to create,
modify or delete a row in this table.

SNMPv2-TCRowStatusr/w

Enumerated Values:

1	off
2	on
3	notApplicable

Description:

.1.3.6.1.4.1.164.12.4.3.1.2.1.7

atmFrCnfgTable

table

.1.3.6.1.4.1.164.12.4.3.1.4 · 1 row entry · 15 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmFrCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmFrCnfgTable'

This table defines virtual connections between ATM and
Frame Relay endpoints.

atmFrCnfgEntry row .1.3.6.1.4.1.164.12.4.3.1.4.1

An entry defines virtual connection between ATM and
Frame Relay endpoint.

Indexes

No indexes recorded

Column Syntax OID

atmFrCnfgCrossConnectIndex

A unique value to identify this cross-connect.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.3.1.4.1.1

atmFrCnfgAtmIfIndex

The ifIndex associated to the ATM interface.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.3.1.4.1.2

atmFrCnfgAtmVpi

The Vpi number of the ATM end point.

Integer32

.1.3.6.1.4.1.164.12.4.3.1.4.1.3

atmFrCnfgAtmVci

The Vci number of the ATM end point.

Integer32

Constraints:
range: 1-47

.1.3.6.1.4.1.164.12.4.3.1.4.1.4

atmFrCnfgFrIfIndex

The ifIndex associated to the Frame Relay
interface.

SNMPv2-SMIInteger32

Constraints:
range: 1-47

.1.3.6.1.4.1.164.12.4.3.1.4.1.5

atmFrCnfgDlci

The DLCI number of the FR end point.

SNMPv2-SMIInteger32

Enumerated Values:

1	ces
2	dbces
3	transparent

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.3.1.4.1.6

atmFrCnfgAdminStatus

This object indicates the connection status requested by the user.

Enumerationr/w

Enumerated Values:

1	off
2	on

.1.3.6.1.4.1.164.12.4.3.1.4.1.7

atmFrCnfgOperStatus

This object indicates the Operational status of the connection.

Enumeration

Enumerated Values:

1	eAndmOrPlar
2	fxoLoopStart
3	fxsLoopStart
4	fxoGroundStart
5	fxsGroundStart
6	r2
7	other

.1.3.6.1.4.1.164.12.4.3.1.4.1.8

atmFrCnfgLastChange

The value of sysUpTime at the time the ATM to FR
connection entered its mandatory operational state.
If the mandatory state was entered prior to the last
re-initialization of the local network management
subsystem, then…

SNMPv2-TCTimeStamp

Constraints:
range: 1-1

Based On: SNMPv2-SMITimeTicks

Description:

.1.3.6.1.4.1.164.12.4.3.1.4.1.9

atmFrCnfgMappingDescrIndex

The value of this object identifies the row
in the atmFrDescrTable.

SNMPv2-SMIInteger32r/w

Constraints:
range: 0-32

.1.3.6.1.4.1.164.12.4.3.1.4.1.10

atmFrCnfgSscsDlci

The DLCI number given to the SSCS Sub-layer for network interworking only
( the default value is 'atmFrCnfgDlci' ).
for Service Interworking do not implement this variable.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.3.1.4.1.11

atmFrCnfgTrafficDescrIndex

The value of this object identifies the row
in the atmTrafficDescrParamTable which
applies to the transmit direction of the VCL.
note :setting this value is allowed only to point2point connections.
for many2one co…

ATM-TC-MIBAtmTrafficDescrParamIndexr/w

Type Constraints:
range: 0..2147483647

.1.3.6.1.4.1.164.12.4.3.1.4.1.12

atmFrCnfgPriority

This object define the priority of connection.
The first parameter affects the transmition of cells in Conjested
network is the bitRate( Cbr has the highest priority and then Vbr,Ubr )
In connections with the same bitRa…

Enumerationr/w

.1.3.6.1.4.1.164.12.4.3.1.4.1.13

atmFrCnfgRowStatus

This object is used to create
a new row or modify or delete an
existing row in this table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.12.4.3.1.4.1.14

atmFrCnfgAllocatedBuffers

This object enables user to limit the amount of buffers
used by the connection.
The limit set by this object will give
the effect of a virtual buffer pool per connection.

The user can allocate between …

Integer32r/w

.1.3.6.1.4.1.164.12.4.3.1.4.1.15

atmDxiCnfgTable

table

.1.3.6.1.4.1.164.12.4.3.2.2 · 1 row entry · 12 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmDxiCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmDxiCnfgTable'

This table defines virtual connections between ATM and
ATM-DXI endpoints.

atmDxiCnfgEntry row .1.3.6.1.4.1.164.12.4.3.2.2.1

An entry defines virtual connection between ATM and
ATM-DXI endpoint.

Indexes

No indexes recorded

Column Syntax OID

atmDxiCnfgCrossConnectIndex

A unique value to identify this cross-connect.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.3.2.2.1.1

atmDxiCnfgAtmIfIndex

The ifIndex associated to the ATM interface.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.3.2.2.1.2

atmDxiCnfgAtmVpi

The Vpi number of the ATM end point.

Integer32

Enumerated Values:

1	up
2	down

.1.3.6.1.4.1.164.12.4.3.2.2.1.3

atmDxiCnfgAtmVci

The Vci number of the ATM end point.

Integer32

Enumerated Values:

1	up
2	down

.1.3.6.1.4.1.164.12.4.3.2.2.1.4

atmDxiCnfgDxiIfIndex

The ifIndex associated to the atm-dxi interface.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.3.2.2.1.5

atmDxiCnfgDfa

The DFA number of the DXI end point.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.3.2.2.1.6

atmDxiCnfgAdminStatus

The requested state of the ATM to DXI connection.

Enumerationr/w

Enumerated Values:

1	atmBridgedEther
2	atmBridgedEtherCRC

.1.3.6.1.4.1.164.12.4.3.2.2.1.7

atmDxiCnfgOperStatus

The real operational status of the ATM to DXI connection.

Enumeration

Enumerated Values:

1	highPriority
2	mediumPriority
3	lowPriority

.1.3.6.1.4.1.164.12.4.3.2.2.1.8

atmDxiCnfgLastChange

The value of sysUpTime at the time the ATM to DXI
connection entered its mandatory operational state.
If the mandatory state was entered prior to the last
re-initialization of the local network management
subsystem, the…

SNMPv2-TCTimeStamp

Based On: SNMPv2-SMITimeTicks

Description:

.1.3.6.1.4.1.164.12.4.3.2.2.1.9

atmDxiCnfgTrafficDescrIndex

The value of this object identifies the row
in the atmTrafficDescrParamTable which
applies to the transmit direction of the VCL.

ATM-TC-MIBAtmTrafficDescrParamIndexr/w

Type Constraints:
range: 0..2147483647

.1.3.6.1.4.1.164.12.4.3.2.2.1.10

atmDxiCnfgPriority

Enumerationr/w

.1.3.6.1.4.1.164.12.4.3.2.2.1.11

atmDxiCnfgRowStatus

This object is used to create a new row or
modify or delete an existing row in this table.

SNMPv2-TCRowStatusr/w

Enumerated Values:

2	no
3	yes
255	notApplicable

Description:

.1.3.6.1.4.1.164.12.4.3.2.2.1.12

atmCbrCnfgTable

table

.1.3.6.1.4.1.164.12.4.3.3.1 · 1 row entry · 15 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmCbrCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmCbrCnfgTable'

This table defines AAL1 virtual connections (not CES) 
between ATM port and DS1-CBR port.

atmCbrCnfgEntry row .1.3.6.1.4.1.164.12.4.3.3.1.1

An entry defines virtual connection between ATM port and
DS1-CBR port.

Indexes

No indexes recorded

Column Syntax OID

atmCbrCnfgAtmIfIndex

The ifIndex associated to the ATM interface.

SNMPv2-SMIInteger32

Enumerated Values:

1	notApplicable
2	none
3	rfc1483
4	pppVcMuxed
5	pppLlcMuxed
6	rfc1483VcMuxed
7	rfc1483BridgePdu

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.3.3.1.1.1

atmCbrCnfgAtmVpi

The Vpi number of the ATM end point.

Integer32

Constraints:
range: 10-217

.1.3.6.1.4.1.164.12.4.3.3.1.1.2

atmCbrCnfgAtmVci

The Vci number of the ATM end point.

Integer32

Enumerated Values:

1	notApplicable
2	disable
3	enable

.1.3.6.1.4.1.164.12.4.3.3.1.1.3

atmCbrCnfgCbrIfIndex

The ifIndex associated to the logical interface of DS0s bundle
or to ifIndex of one of the data ports.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.3.3.1.1.4

atmCbrCnfgAdminStatus

The requested status of the connection.

Enumerationr/w

.1.3.6.1.4.1.164.12.4.3.3.1.1.5

atmCbrCnfgOperStatus

The real operational status of the connection.

Enumeration

.1.3.6.1.4.1.164.12.4.3.3.1.1.6

atmCbrCnfgLastChange

The value of sysUpTime at the time the ATM to CBR
connection entered its mandatory operational state.
If the mandatory state was entered prior to the last
re-initialization of the local network management
subsystem, the…

SNMPv2-TCTimeStamp

Constraints:
range: 1-4095

Based On: SNMPv2-SMITimeTicks

Description:

.1.3.6.1.4.1.164.12.4.3.3.1.1.7

atmCbrCnfgAAL1Signalling

Not in use. Must be always 'off'.

Enumerationr/w

Constraints:
range: 0-65535

.1.3.6.1.4.1.164.12.4.3.3.1.1.8

atmCbrCnfgRxTimeSlots

This value indicates the time-slots used by this connection for receiving.
It uses 32 bits for E1 and low 24 bits for T1.
each bit represents a time slot for receiving :
time-slot 0 = bit 0 (LSB - most right bit in las…

TimeSlotsr/w

.1.3.6.1.4.1.164.12.4.3.3.1.1.9

atmCbrCnfgRxBytesPerCell

number of bytes to be receive in order per cell to low the delay.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.3.3.1.1.10

atmCbrCnfgTxTimeSlots

TimeSlotsr/w

.1.3.6.1.4.1.164.12.4.3.3.1.1.11

atmCbrCnfgTxBytesPerCell

number of bytes to be transmit in order per cell to low the delay.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	rx
2	tx
3	both

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.3.3.1.1.12

atmCbrCnfgParity

Controls the use of pointer parity when using
the STRUCTURED or STRUCTURED WITH POINTER connection type.
as defined by atmCbrCnfgService.
ON - Pointer parity bit generation at the transmit side,
an…

Enumerationr/w

Enumerated Values:

1	link1
2	link2
3	link3
4	link4
5	internal
6	external
7	automatic
8	loopback

.1.3.6.1.4.1.164.12.4.3.3.1.1.13

atmCbrCnfgRowStatus

This object is used to create a new row or
modify or delete an existing row in this table.

SNMPv2-TCRowStatusr/w

Enumerated Values:

1	notApplicable
2	down
3	up

Description:

.1.3.6.1.4.1.164.12.4.3.3.1.1.14

atmCbrCnfgService

Define if DSx service is structured or unstructured.
A structured(3) interface is some nx64Kbps. (n x DS0 = n Time Slots)
An unstructured (2) interface is full DSx, x >0.
(1.544Mbps, 2.048Mbps, 6.312Mbps, 44.736 Mbps,…

Enumerationr/w

.1.3.6.1.4.1.164.12.4.3.3.1.1.15

atmCESConfExtnsTable

table

.1.3.6.1.4.1.164.12.4.3.3.2 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmCESConfExtnsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmCESConfExtnsTable'

This table defines virtual connections between ATM port and
DS1-CBR port.

atmCESConfExtnsEntry row .1.3.6.1.4.1.164.12.4.3.3.2.1

An entry defines virtual connection between ATM port and
DS1-CBR port.

Indexes

No indexes recorded

Column Syntax OID

atmCESLastChange

SNMPv2-TCTimeStamp

Enumerated Values:

1	link1
2	link2
3	link3
4	link4
5	internal
6	external
7	automatic
8	loopback
255	notApplicable

Based On: SNMPv2-SMITimeTicks

Description:

.1.3.6.1.4.1.164.12.4.3.3.2.1.1

atmCESRxBytesPerCell

Number of bytes to be received per cell, in order to decrease the delay.

Integer32r/w

.1.3.6.1.4.1.164.12.4.3.3.2.1.2

atmCESTxBytesPerCell

Number of bytes to be transmitted per cell, in order to decrease the delay.

Integer32r/w

Enumerated Values:

1	off
2	on

.1.3.6.1.4.1.164.12.4.3.3.2.1.3

atmCESAal1Type

Type of CBR connection: CES , DBCES or transparent .

Enumerationr/w

Enumerated Values:

1	notApplicable
2	e1t1
3	shdsl

.1.3.6.1.4.1.164.12.4.3.3.2.1.4

atmCESParity

Indicate if we'll add even parity to the pointer of the structure of CES.

Enumerationr/w

.1.3.6.1.4.1.164.12.4.3.3.2.1.5

atmCESSigType

type of signalling for a DBCES connection.
Must be 'other' for CES connection.

Enumerationr/w

.1.3.6.1.4.1.164.12.4.3.3.2.1.6

atmCESSigABBits

This attribute is applicable only when value of atmCESSigType is other.
Represents the AB bits for Rx/Tx and their masks in this way:
bits 7..6: Tx AB bits value,
bits 5..4: Tx AB bits mask,
bits 3..2: Rx AB bits value,…

OctetStringr/w

Enumerated Values:

1	main
2	sub

.1.3.6.1.4.1.164.12.4.3.3.2.1.7

atmCESConnectionName

The Connection's name.

OctetStringr/w

.1.3.6.1.4.1.164.12.4.3.3.2.1.8

atmCESTcPattern

Trunk conditioning data pattern to be sent upon a DS0 fail.
Range is 0x0..0xFF.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.3.3.2.1.9

atmEtherCnfgTable

table

.1.3.6.1.4.1.164.12.4.3.4.2 · 1 row entry · 21 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmEtherCnfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmEtherCnfgTable'

This table defines virtual connections between ATM and
ATM-BridgedEthernet endpoints.

atmEtherCnfgEntry row .1.3.6.1.4.1.164.12.4.3.4.2.1

An entry defines virtual connection between ATM and
ATM-Ethernet endpoint.

Indexes

No indexes recorded

Column Syntax OID

atmEtherCnfgCrossConnectIndex

A unique value to identify this cross-connect.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.3.4.2.1.1

atmEtherCnfgAtmIfIndex

The ifIndex associated to the ATM interface.

SNMPv2-SMIInteger32

Enumerated Values:

1	main
2	sub

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.3.4.2.1.2

atmEtherCnfgAtmVpi

The Vpi number of the ATM end point.

Integer32

Constraints:
range: 1-1

.1.3.6.1.4.1.164.12.4.3.4.2.1.3

atmEtherCnfgAtmVci

The Vci number of the ATM end point.

Integer32

Constraints:
range: 1-32

.1.3.6.1.4.1.164.12.4.3.4.2.1.4

atmEtherCnfgEtherIfIndex

The ifIndex associated to the atm-Ethernet interface.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.3.4.2.1.5

atmEtherCnfgMacAddrdeprecated

The DFA number of the Ethernet end point.

MacAddress

Type Constraints:
range: 6

.1.3.6.1.4.1.164.12.4.3.4.2.1.6

atmEtherCnfgAdminStatus

The requested state of the ATM to Ethernet connection.

Enumerationr/w

.1.3.6.1.4.1.164.12.4.3.4.2.1.7

atmEtherCnfgOperStatus

The real operational status of the ATM to Ethernet connection.

Enumeration

Constraints:
range: 1-8

.1.3.6.1.4.1.164.12.4.3.4.2.1.8

atmEtherCnfgLastChange

The value of sysUpTime at the time the ATM to Ethernet
connection entered its current operational state.
If the current state was entered prior to the last
re-initialization of the local network management
subsystem, th…

SNMPv2-TCTimeStamp

Based On: SNMPv2-SMITimeTicks

Description:

.1.3.6.1.4.1.164.12.4.3.4.2.1.9

atmEtherCnfgTrafficDescrIndex

The value of this object identifies the row
in the atmTrafficDescrParamTable which
applies to the transmit direction of the VCL.

ATM-TC-MIBAtmTrafficDescrParamIndexr/w

Type Constraints:
range: 0..2147483647

.1.3.6.1.4.1.164.12.4.3.4.2.1.10

atmEtherCnfgEncapsulationModedeprecated

This object define the encapsulation type requested
for the connection.
it indicates if we transfer the Ethernet frame to the
atm side without the Crc32- AtmBridgedEther,
or with it - AtmBridgedEther_CRC.

Enumerationr/w

.1.3.6.1.4.1.164.12.4.3.4.2.1.11

atmEtherCnfgPriority

This object define the priority of connection.
The first parameter affects the transmition of cells in Conjested
network is the Service Category( Cbr has the highest priority and then Vbr,Ubr )
In connections with the s…

Enumerationr/w

.1.3.6.1.4.1.164.12.4.3.4.2.1.12

atmEtherCnfgRowStatus

This object is used to create a new row or
modify or delete an existing row in this table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.12.4.3.4.2.1.13

atmEtherCnfgRouterIP

The interface IP address for SNMP requests.

RFC1155-SMIIpAddressr/w

Enumerated Values:

1	accessOnly
2	accessAndSwitching

Type Constraints:
range: 4

.1.3.6.1.4.1.164.12.4.3.4.2.1.14

atmEtherCnfgRouterMask

The interface IP address mask for SNMP requests.

RFC1155-SMIIpAddressr/w

Enumerated Values:

2	disable
3	enable

Type Constraints:
range: 4

.1.3.6.1.4.1.164.12.4.3.4.2.1.15

atmEtherCnfgRouterFragmentation

Fragmentation. When application is not router value must be 'notApplicable'.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	admitAll
3	admitOnlyVlanTagged
4	admitOnlyUnTagged

.1.3.6.1.4.1.164.12.4.3.4.2.1.16

atmEtherCnfgRouterRIPMode

RIP Mode. When application is not router value must be 'notApplicable'.

Enumerationr/w

.1.3.6.1.4.1.164.12.4.3.4.2.1.17

atmEtherCnfgRouterMTUdeprecated

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	unTagged
3	tagged

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.3.4.2.1.18

atmEtherCnfgPPPEncapsulation

This object define the encapsulation type requested
for the connection.

rfc1483 - Multiprotocol Encapsulation over
ATM Adaptation Layer 5 (no PPP),
LLC Muxed.
…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	admitAll
3	admitOnlyVlanTagged
4	admitOnlyUnTagged

.1.3.6.1.4.1.164.12.4.3.4.2.1.19

atmEtherCnfgAllocatedBuffers

Integer32r/w

Enumerated Values:

7	deleteLanTable
255	noOp

.1.3.6.1.4.1.164.12.4.3.4.2.1.20

atmEtherCnfgPauseTrigger

Enable/Disable LAN Pause triger from WAN connection

Enumerationr/w

Enumerated Values:

1	svl
2	ivl

.1.3.6.1.4.1.164.12.4.3.4.2.1.21

atmTranslateTable

table

.1.3.6.1.4.1.164.12.4.3.5.1 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmTranslateTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmTranslateTable'

This table translates the three of AtmIfIndex,AtmVpi,AtmVci
to ifIndex of the interface on the user port's side.

atmTranslateEntry row .1.3.6.1.4.1.164.12.4.3.5.1.1

An entry includes the User side interface's ifIndex of any virtual
connection along with the ATM connection indices.

Indexes

No indexes recorded

Column Syntax OID

atmTranslateAtmIfIndex

The ifIndex associated to the ATM interface.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.3.5.1.1.1

atmTranslateAtmVpi

The Vpi number of the ATM end point.

Integer32

Enumerated Values:

1	service
2	network

.1.3.6.1.4.1.164.12.4.3.5.1.1.2

atmTranslateAtmVci

The Vci number of the ATM end point.

Integer32

.1.3.6.1.4.1.164.12.4.3.5.1.1.3

atmTranslateUserIfIndex

The ifIndex associated to the user interface.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.4.3.5.1.1.4

imaXLinkTable

table

.1.3.6.1.4.1.164.12.5.2 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk imaXLinkTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::imaXLinkTable'

The IMA Link Status and Configuration table.
This table contains additional objects for the link table.

imaXLinkEntry row .1.3.6.1.4.1.164.12.5.2.1

An entry in the IMA Link table.

Indexes

No indexes recorded

Column	Syntax	OID
imaLinkDirection the Link direction.	Enumerationr/w	`.1.3.6.1.4.1.164.12.5.2.1.1`
imaLinkItcLBClkSrc Clock source for the current Tx-line.	Enumerationr/w	`.1.3.6.1.4.1.164.12.5.2.1.2`
imaLinkActivation IMA Link activation at ATM layer.	Enumerationr/w	`.1.3.6.1.4.1.164.12.5.2.1.3`

imaXGroupTable

table

.1.3.6.1.4.1.164.12.5.3 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk imaXGroupTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::imaXGroupTable'

The IMA group Status and Configuration table.
This table contains additional objects for the Group table.

imaXGroupEntry row .1.3.6.1.4.1.164.12.5.3.1

An entry in the IMA Group table.

Indexes

No indexes recorded

Column	Syntax	OID
imaGroupVersion IMA Version.	Enumerationr/w	`.1.3.6.1.4.1.164.12.5.3.1.1`
imaGroupCtcTxClkSrc The source of the transmitted, common, Clock Source. Applicable if imaGroupNeTxClkMode=ctc(1). Automatic - Dynamic source, taken from the currently reference link. Internal - taken from the Internal clock on card. Loo…	Enumerationr/w	`.1.3.6.1.4.1.164.12.5.3.1.2`
imaGroupCtcTxClkSrcPort This parameter is valid only when imaGroupCtcTxClkSrc=loopback. The value may be any port identifier.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.5.3.1.3`
imaGroupRestart off(1)- default state. After on(2) operation ends, value should be automatically set to off(1). on(2) - restarts the IMA Group State Machine (GSM) and the Rx\Tx Link State Machines (Rx/Tx LSM).	Enumerationr/w Constraints: `range: 1-96`	`.1.3.6.1.4.1.164.12.5.3.1.4`
imaGroupType This parameter defines the Type of IMA Group (which determines its Links Type).	Enumerationr/w	`.1.3.6.1.4.1.164.12.5.3.1.5`

atmLayer2XVclTable

table

.1.3.6.1.4.1.164.12.7.1 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmLayer2XVclTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmLayer2XVclTable'

This table is an extension of VCL table, which is created  
for each LAN VCC.

atmLayer2XVclEntry row .1.3.6.1.4.1.164.12.7.1.1

Conceptual row in atmVclTable.
This table augments the RFC2515 VCL table.

Indexes

No indexes recorded

Column	Syntax	OID
atmLayer2XVclConnMode Each valid LAN VCC is either Main or Sub. This parameter is configured only once on creation of a LAN VCC. It can not be changed after creation. In order to change the Mode, user should delete the connection and creat…	Enumerationr/w	`.1.3.6.1.4.1.164.12.7.1.1.1`
atmLayer2XVclGroupIdx The group identifier. A VCC Group identifier = 0 if the VCC was not associated with a group yet. This value is updated according to the group identifier set by atmLayer2GroupTable.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.7.1.1.2`

atmLayer2GroupTable

table

.1.3.6.1.4.1.164.12.7.2 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmLayer2GroupTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmLayer2GroupTable'

This table contains groups and their members.
A group is a bundle of VCCs, which acts as different queues.
Main and Sub VCCs should have the same ATM slot and port,
and the same LAN slot and port.
Each group contains: 1 to <number of priorities> VCCs.

atmLayer2GroupEntry row .1.3.6.1.4.1.164.12.7.2.1

Conceptual row in atmLayer2GroupTable.
The indexes: ifIndex, atmVclVpi and atmVclVci indicate
the Network ATM End-Point.
Upon a group creation, one Main VCC must be added first.
After the group was created, Sub VCCs ma…

Indexes

No indexes recorded

Column Syntax OID

atmLayer2GroupIdx

The group identifier.
0 is not a valid index.

SNMPv2-SMIInteger32

Enumerated Values:

2	normal
3	spaced

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.7.2.1.1

atmLayer2GroupRowStatus

Creation/Deletion of rows in the table, and indication of the
entry's status.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.12.7.2.1.2

atmLayer2GroupConnMode

Each valid LAN VCC is either Main or Sub as configured in
atmLayer2XVclTable.

Enumeration

.1.3.6.1.4.1.164.12.7.2.1.3

atmLayer2GroupConnPriority

This parameter is configured by atmLayer2PriorityRx from
atmLayer2PriorityTable.
Each bit in the Octet represents a specific priority as follows:

MSB 7 6 5 4 …

OctetString

Enumerated Values:

1	notApplicable
2	static
3	inAtmArp

.1.3.6.1.4.1.164.12.7.2.1.4

atmLayer2GroupName

Group name. Configured by the user.
The name is unique per system.
For atmLayer2GroupIdx=0, the name will be null.

OctetStringr/w

.1.3.6.1.4.1.164.12.7.2.1.5

atmLayer2PriorityTable

table

.1.3.6.1.4.1.164.12.7.3 · 1 row entry · 5 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmLayer2PriorityTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmLayer2PriorityTable'

This table maps all priorities inside a group.
Several priorities might be mapped to the same VCC. 
Upon priority change, the agent will update the VCCs of the 
changed priority in this table, and will update	-
atmLayer2GroupConnPriority parameter of both former and new owners 
of the changed priority.
Changing a VCC value is actually a change of three parameters
simultaneously: atmLayer2PriorityIfIndex, atmLayer2PriorityVclVpi
and atmLayer2PriorityVclVci. Otherwise, the set will be rejected,
since there might be that such VCC doesn't exist in the specific
group.

atmLayer2PriorityEntry row .1.3.6.1.4.1.164.12.7.3.1

Conceptual row in atmLayer2PriorityTable.
Each entry is a Network ATM End-Point per priority.
Upon a group creation, all priorities are mapped to the Main VCC.
Number of entries per group is according to the number of …

Indexes

pwIdx

Column Syntax OID

atmLayer2PriorityGroupIdx

The group identifier.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.7.3.1.1

atmLayer2PriorityRx

The priority values.
The used values are 0-7, but since this value is part of the index
of the table, and in order to avoid '0' as an index, the index syntax
is 1..8, but the real value is atmLayer2PriorityRx-1:
0 …

Integer32

.1.3.6.1.4.1.164.12.7.3.1.2

atmLayer2PriorityIfIndex

ATM ifIndex of the network End-Point.

IF-MIBInterfaceIndexr/w

Type Constraints:
range: 1..2147483647

Description:

.1.3.6.1.4.1.164.12.7.3.1.3

atmLayer2PriorityVclVpi

Vpi of the network End-Point.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.7.3.1.4

atmLayer2PriorityVclVci

Vci of the network End-Point.

SNMPv2-SMIInteger32r/w

Enumerated Values:

1	notApplicable
2	disabled
3	enabled

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.7.3.1.5

atmLayer2CfgTable

table

.1.3.6.1.4.1.164.12.7.5 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmLayer2CfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmLayer2CfgTable'

Bridge configuration Table. This table supports multi-bridge 
and bridge features within an ATM device.

atmLayer2CfgEntry row .1.3.6.1.4.1.164.12.7.5.1

Conceptual row in atmLayer2CfgTable.
Each entry in this table contains the bridging attributes for
both Ethernet and ATM sides.
The interface index is the Ethernet port interface.

For Ace52: this object rep…

Indexes

No indexes recorded

Column Syntax OID

atmLayer2CfgBridgingMode

Enumerationr/w

Enumerated Values:

1	notApplicable
2	atmVc
3	bridgePort
4	ipV4

.1.3.6.1.4.1.164.12.7.5.1.1

atmLayer2CfgVlanMode

VLAN Mode. Upon Mode changing, all LAN VCCs will be deleted
by the agent from all tables that include LAN VCCs.

Enumerationr/w

.1.3.6.1.4.1.164.12.7.5.1.2

atmLayer2CfgAtmAcceptableFrameType

The Frame Type that will be acceptable by the VCCs that
are associated with this Ethernet port.
Frames which don't match the selected type will be discarded.

admitAll - all frames will be acc…

Enumerationr/w

.1.3.6.1.4.1.164.12.7.5.1.3

atmLayer2CfgAtmIngressFiltering

For the VCCs that are associated with this Ethernet port,
when this is true(1) the device will discard incoming
frames for VLANs which do not include this Port in its
Member set. When false(2), the port will accept al…

SNMPv2-TCTruthValuer/w

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.164.12.7.5.1.4

atmLayer2CfgAtmTxFrameType

The Frame Type that will be transmitted by the VCCs that
are associated with this Ethernet port.

unTagged - The transmitted frames will be unTagged.
tagged - The transmitted frames will be T…

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disabled
3	enabled

.1.3.6.1.4.1.164.12.7.5.1.5

atmLayer2CfgEthAcceptableFrameType

The Frame Type that this Ethernet port will accept.
(for ACE-52: the Frame Type that this Bridge will accept)
This parameter is notApplicable for atmLayer2VlanMode=disable.
Frames which don't match the selected type wil…

Enumerationr/w

Constraints:
range: 1-4095

.1.3.6.1.4.1.164.12.7.5.1.6

atmLayer2CfgBridgeAction

This object enables to perform the specified action on the
selected port.

Enumerationr/w

Constraints:
range: 0-7

.1.3.6.1.4.1.164.12.7.5.1.7

atmLayer2CfgLearningMode

This object specifies the mode of the learning process of a bridge.
svl - Shared VLAN process. If an individual MAC Address is learned
in one VLAN, this information is used in forwarding decisions
taken for…

Enumerationr/w

.1.3.6.1.4.1.164.12.7.5.1.8

atmLayer2CfgAgingTime

The timeout period in seconds for aging out
dynamically learned forwarding information.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.7.5.1.9

frAtmIwfXConnectionTable

table

.1.3.6.1.4.1.164.12.8.1 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk frAtmIwfXConnectionTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::frAtmIwfXConnectionTable'

This table is an extension of frAtmIwfXConnectionTable from
RFC2955.

frAtmIwfXConnectionEntry row .1.3.6.1.4.1.164.12.8.1.1

Conceptual row in frAtmIwfXConnectionTable.
This table augments the RFC2955.

Indexes

No indexes recorded

Column	Syntax	OID
frAtmIwfXConnMode FR IWF Mode. service - Service InterWorking (FRF.8), network - Network InterWorking (FRF.5).	Enumerationr/w	`.1.3.6.1.4.1.164.12.8.1.1.1`
frAtmIwfXConnSscsDlci This parameter is relevant for frAtmIwfXConnMode=network (FRF.5) only. This parameter allow configuration of the FR SSCS DLCI that is transferred to the remote FR unit.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.164.12.8.1.1.2`

atmCesAal1CurrentTable

table

.1.3.6.1.4.1.164.12.9.1.1 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmCesAal1CurrentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmCesAal1CurrentTable'

The AAL1 Current table.

atmCesAal1CurrentEntry row .1.3.6.1.4.1.164.12.9.1.1.1

An entry in the AAL1 Current table.

Indexes

No indexes recorded

Column Syntax OID

atmCesAal1CurrentIfIndex

The index of the AAL1 interface.
It may be ifIndex.

SNMPv2-SMIInteger32

Enumerated Values:

2	ingress
3	egress

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.9.1.1.1.1

atmCesAal1CurrentSeqErrors

The counter associated with the number of Discarded
cells due to wrong sequence number, encountered
by an AAL1 interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.9.1.1.1.2

atmCesAal1CurrentHdrErrors

The counter associated with the number of Discarded
cells due to bad AAL1 header error (including correctable
and uncorrectable CRC, and bad parity), encountered
by an AAL1 interface in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.9.1.1.1.3

atmCesAal1CurrentPointerReframes

The counter associated with the number of events in
which a SDT pointer isn't where it is expected to be,
and must be reacquired, encountered by an AAL1 interface
in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.9.1.1.1.4

atmCesAal1CurrentBufUnderflows

The counter associated with the number of buffer
underflow events, encountered by an AAL1 interface
in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.9.1.1.1.5

atmCesAal1CurrentBufOverflows

The counter associated with the number of buffer
overflow events, encountered by an AAL1 interface
in the current 15 minute interval.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.9.1.1.1.6

atmCesAal1IntervalTable

table

.1.3.6.1.4.1.164.12.9.1.2 · 1 row entry · 7 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmCesAal1IntervalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmCesAal1IntervalTable'

The AAL1 Interval table.

atmCesAal1IntervalEntry row .1.3.6.1.4.1.164.12.9.1.2.1

An entry in the AAL1 Interval table.

Indexes

No indexes recorded

Column Syntax OID

atmCesAal1IntervalIfIndex

The index of the AAL1 interface.
It may be ifIndex.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.164.12.9.1.2.1.1

atmCesAal1IntervalNumber

A number between 1 and 96, where 1 is the most
recently completed 15 minute interval and 96 is
the least recently completed 15 minutes interval
(assuming that all 96 intervals exist).

Integer32

.1.3.6.1.4.1.164.12.9.1.2.1.2

atmCesAal1IntervalSeqErrors

The counter associated with the number of Discarded
cells due to wrong sequence number, encountered
by an AAL1 interface in one of the previous 96,
individual 15 minute, intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.9.1.2.1.3

atmCesAal1IntervalHdrErrors

The counter associated with the number of Discarded
cells due to bad AAL1 header error (including correctable
and uncorrectable CRC, plus bad parity), encountered
by an AAL1 interface in one of the previous 96,
indi…

SNMPv2-SMIGauge32

Enumerated Values:

1	notApplicable
2	no
3	yes

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.9.1.2.1.4

atmCesAal1IntervalPointerReframes

The counter associated with the number of events in
which a SDT pointer isn't where it is expected to be,
and must be reacquired, encountered by an AAL1 interface
in one of the previous 96, individual 15 minute,
int…

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.9.1.2.1.5

atmCesAal1IntervalBufUnderflows

The counter associated with the number of buffer
underflow events, encountered by an AAL1 interface
in one of the previous 96, individual 15 minute,
intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.9.1.2.1.6

atmCesAal1IntervalBufOverflows

The counter associated with the number of buffer
overflow events, encountered by an AAL1 interface
in one of the previous 96, individual 15 minute,
intervals.

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.12.9.1.2.1.7

atmCesXConfTable

table

.1.3.6.1.4.1.164.12.9.2.1 · 1 row entry · 1 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmCesXConfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmCesXConfTable'

This table is an extension of atmfCESConfTable table.

atmCesXConfEntry row .1.3.6.1.4.1.164.12.9.2.1.1

Conceptual row in atmfCESConfTable.
A new row is created in this table upon each new CES VCC creation.

Indexes

No indexes recorded

Column	Syntax	OID
atmCesXConfCBRMode This parameter defines if to use Spaced or Normal CBR. Normal - TD will be allocated from the policing range (described in ACE2002 NMS SRS). The PCR is expanded with a constant value…	Enumerationr/w	`.1.3.6.1.4.1.164.12.9.2.1.1.1`

atmIpoaLisIfMappingXTable

table

.1.3.6.1.4.1.164.12.10.1 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk atmIpoaLisIfMappingXTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::atmIpoaLisIfMappingXTable'

This table is an extension of a table 
from RFC 2320: ipoaLisIfMappingTable - 
The ATM Logical IP Subnet Interface Mapping Table.

atmIpoaLisIfMappingXEntry row .1.3.6.1.4.1.164.12.10.1.1

Conceptual row in ipoaLisIfMappingTable.

Indexes

pwIdx

Column	Syntax	OID
atmIpoaLisIfMappingType This object indicates the Mapping Type.	Enumerationr/w	`.1.3.6.1.4.1.164.12.10.1.1.1`
atmIpoaLisIfMappingIPAddress This parameter is applicable for atmIpoaLisIfMappingTypeIP=static(2). This parameter is the IP Address assigned by the user when applicable.	RFC1155-SMIIpAddressr/w Type Constraints: `range: 4`	`.1.3.6.1.4.1.164.12.10.1.1.2`

pwGenTable

table

.1.3.6.1.4.1.164.14.1.1.1 · 1 row entry · 19 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pwGenTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pwGenTable'

This table contains general configuration for 
PW connection.

pwGenEntry row .1.3.6.1.4.1.164.14.1.1.1.1

This table is indexed by pwIdx, the value of which is equal
to the same index that was created for the associated entry
in the PW Table (in the PW-STD-MIB)- the pwIndex.
An entry is created in this table by the agent …

Indexes

No indexes recorded

Column Syntax OID

pwIdx

Index of this table.
The value for this object is equal to the value
of pwIndex from the pwTable of PW-STD-MIB

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.14.1.1.1.1.1

pwGenPeerIdx

This object indicates the Index of the Peer
(as it is defined in the Peer Table), which terminated this PW.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	notApplicable
2	v1
3	v2

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.14.1.1.1.1.2

pwGenAttachmentCircuit

This is a unique index within the ifTable. It represents
the attached circuit interface (e.g ATM VC, HDLC) attached to
this PW connection (from service initiator side).

A value of zero indicates an inte…

IF-MIBInterfaceIndexOrZeror/w

Enumerated Values:

1	notApplicable
2	dsx1E1
3	dsx1ESF
4	dsx1SF
5	unframed

Type Constraints:
range: 0..2147483647

Description:

.1.3.6.1.4.1.164.14.1.1.1.1.3

pwGenOutgoingInterface

This is a unique index within the ifTable. It represents
the outgoing interface (towards the PSN ) attached to
this PW connection.

This object is applicable only for MPLS peer, for device
without …

IF-MIBInterfaceIndexOrZeror/w

Enumerated Values:

1	notApplicable
2	disable
3	enable

Type Constraints:
range: 0..2147483647

Description:

.1.3.6.1.4.1.164.14.1.1.1.1.4

pwGenOamMode

This objects defines whether OAM will be enabled on this PW.
notApplicable(1) value will be used when
PW type does not support OAM.

Enumerationr/w

.1.3.6.1.4.1.164.14.1.1.1.1.5

pwGenOamType

This objects defines the failure detection mechanism used
on this PW.
BFD - Bidirectional Forwarding Detection
notApplicable(1) value will be used when
pwGenOamMode is notApplicable.

Enumerationr/w

.1.3.6.1.4.1.164.14.1.1.1.1.6

pwGenSequenceNumberField

This object defines whether processing of Sequence Number field
(ATM cell encapsulation) will be done by device, on this PW.

Enumerationr/w

.1.3.6.1.4.1.164.14.1.1.1.1.7

pwGenNextHopType

Indicates address type of the Next Hop.
Not applicable for device with router.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	disabled
3	enabled

.1.3.6.1.4.1.164.14.1.1.1.1.8

pwGenNextHop

Not applicable (=0) when pwMplsEgressTunnelNextHopType=notApplicable.
When applicable, represents ATM VC, Bridge Port,
according to pwMplsEgressTunnelNextHopType.

SNMPv2-SMIUnsigned32r/w

Enumerated Values:

1	notApplicable
2	atm
3	router

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.14.1.1.1.1.9

pwGenIpNextHop

This object defines local Next Hop IP Address for this PW.
0.0.0.0 - means - not applicable.
This object is applicable only when pwGenNextHopType=ipV4

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.14.1.1.1.1.10

pwGenMacNextHop

This object defines local Next Hop MAC Address for this PW.
0:0:0:0:0:0 - means - not applicable.
This object is applicable only when pwGenNextHopType=bridgePort

MacAddressr/w

Type Constraints:
range: 6

.1.3.6.1.4.1.164.14.1.1.1.1.11

pwGenEnableVlanTag

This object enables or diables a VLAN tag on
every transmitted paket via this PW connection

Enumerationr/w

.1.3.6.1.4.1.164.14.1.1.1.1.12

pwGenVlanId

This object indicates the VLAN ID tag attached
to every transmitted packet via this PW connection.
This entry is applicable only if pwGenEnableVlanTag=enabled (3).

Unsigned32r/w

Constraints:
range: 10-10
range: 17-17
range: 24-24

.1.3.6.1.4.1.164.14.1.1.1.1.13

pwGenVlanPriority

This object indicates the VLAN priority assigned
to every transmitted packet via this PW connection.
This entry is applicable only if pwGenEnableVlanTag=enabled (3)

Unsigned32r/w

Enumerated Values:

0	pwFrDeIncomingMarking
1	pwFrFecnIncomingMarking
2	pwFrBecnIncomingMarking
3	pwFrDeOutgoingMarking
4	pwFrFecnOutgoingMarking
5	pwFrBecnOutgoingMarking

.1.3.6.1.4.1.164.14.1.1.1.1.14

pwGenIpTos

This object indicates TOS field value
for pw having pwPsnType= ip (3)

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.14.1.1.1.1.15

pwGenSourceUdpPort

This object indicates source UDP port (1...65535) value
for pw having pwPsnType= ip (3)

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.14.1.1.1.1.16

pwGenSubType

This object indicates the PW Sub Type
(i.e. Sub Type of 'pwType' from 'pwTable').

For ACE-3000 devices:
It is applicable only when pwType = basicCesPsn(21).

Enumerationr/w

.1.3.6.1.4.1.164.14.1.1.1.1.17

pwGenSourceIpAddress

Source IP Address per PW

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.14.1.1.1.1.18

pwGenSourceIpMask

Source IP Mask per PW

RFC1155-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.164.14.1.1.1.1.19

pwGenLabelTable

table

.1.3.6.1.4.1.164.14.1.1.5 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pwGenLabelTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pwGenLabelTable'

This table defines supported range of PW labels.

pwGenLabelEntry row .1.3.6.1.4.1.164.14.1.1.5.1

Entry in this table defines range of PW labels in the direction and type
indicated by pwGenLabelType and pwGenLabelDirection.

Indexes

pwIdx pwPerfIntervalXNumber

Column	Syntax	OID
pwGenLabelType This object defines type of label.	Enumeration Constraints: `range: 1-96`	`.1.3.6.1.4.1.164.14.1.1.5.1.1`
pwGenLabelDirection This object defines PW direction.	Enumeration	`.1.3.6.1.4.1.164.14.1.1.5.1.2`
pwGenLabelMinValue This object defines minimum value of PW labels, in the direction and type indicated by pwGenLabelType and pwGenLabelDirection.	SNMPv2-SMIUnsigned32r/w Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.14.1.1.5.1.3`
pwGenLabelMaxValue This object define maximum value of PW labels, in the direction and type indicated by pwGenLabelType and pwGenLabelDirection.	SNMPv2-SMIUnsigned32r/w Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.14.1.1.5.1.4`

peerTable

table

.1.3.6.1.4.1.164.14.1.1.6 · 1 row entry · 9 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk peerTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::peerTable'

The Peer Table

peerEntry row .1.3.6.1.4.1.164.14.1.1.6.1

An entry in this table.

Indexes

No indexes recorded

Column Syntax OID

peerIndex

This object represents the Peer Index.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.14.1.1.6.1.1

peerRowStatus

This object is used for creating, modifying and deleting
a row of this table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.14.1.1.6.1.2

peerAddressType

This object represents the Address Type of the Peer node.
It should be set to 'unknown' if PE/PW maintenance protocol
is not used and the address is unknown.

INET-ADDRESS-MIBInetAddressTyper/w

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.164.14.1.1.6.1.3

peerAddress

This object represents the Peer node Address.
of the PW/PE maintenance protocol entity.
This object SHOULD contain a value of all zeroes if not applicable
(peerAddrType is 'unknown').

INET-ADDRESS-MIBInetAddressr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.14.1.1.6.1.4

peerName

This object represents the Peer Name.

SNMP-FRAMEWORK-MIBSnmpAdminStringr/w

Constraints:
range: 1-96

.1.3.6.1.4.1.164.14.1.1.6.1.5

peerNoOfUsages

This object indicates the number of times this Peer is used
(by PWs, Egress LSP Tunnels etc).

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.14.1.1.6.1.6

peerTargeted

This object indicates whether the Peer is configured
as a Targeted Peer or not.

Enumerationr/w

.1.3.6.1.4.1.164.14.1.1.6.1.7

peerNextHopAddressType

This object represents the Address Type of the Peer Next Hop node.
It should be set to 'unknown' if the address is unknown.

INET-ADDRESS-MIBInetAddressTyper/w

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.164.14.1.1.6.1.8

peerNextHopAddress

This object represents the Peer Next Hop node Address.
This object SHOULD contain a value of all zeroes if not applicable
(peerAddrType is 'unknown').

INET-ADDRESS-MIBInetAddressr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.164.14.1.1.6.1.9

pwMplsCfgTable

table

.1.3.6.1.4.1.164.14.1.2.1.1 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pwMplsCfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pwMplsCfgTable'

This table contains MPLS PSN related configuration for 
PW connection.

pwMplsCfgEntry row .1.3.6.1.4.1.164.14.1.2.1.1.1

Indexes

No indexes recorded

Column	Syntax	OID
pwMplsCfgIngressTunnel This object points to an entry of pwMplsIngressTunnelTable. Its value is equal to pwMplsIngressTunnelIndex	SNMPv2-SMIUnsigned32r/w Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.14.1.2.1.1.1.1`
pwMplsCfgEgressTunnel This object points to an entry of pwMplsEgressTunnelTable. Its value is equal to pwMplsEgressTunnelIndex.	SNMPv2-SMIUnsigned32r/w Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.14.1.2.1.1.1.2`

pwTDMoIpTable

table

.1.3.6.1.4.1.164.14.1.3.1.1 · 1 row entry · 1 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pwTDMoIpTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pwTDMoIpTable'

This table contains TDMoIP Service  related configuration for 
PW connection.

pwTDMoIpEntry row .1.3.6.1.4.1.164.14.1.3.1.1.1

Indexes

No indexes recorded

Column	Syntax	OID
pwTDMoIpCfgIndex Index to TDMoIP table below. Multiple TDMoIP PWs MAY share a single pwTDMoIpCfgEntry	SNMPv2-SMIUnsigned32r/w Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.14.1.3.1.1.1.1`

pwTDMoIpCfgTable

table

.1.3.6.1.4.1.164.14.1.3.1.3 · 1 row entry · 6 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pwTDMoIpCfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pwTDMoIpCfgTable'

This table contains TDM over IP service configuration 
for PW connection.

pwTDMoIpCfgEntry row .1.3.6.1.4.1.164.14.1.3.1.3.1

Indexes

No indexes recorded

Column Syntax OID

pwTDMoIpCfgTableIndex

Index to an entry in this table

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.14.1.3.1.3.1.1

pwTDMoIpCfgRowStatus

Object used for creating, modifying, and deleting
a row of this table.

SNMPv2-TCRowStatusr/w

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.164.14.1.3.1.3.1.2

pwTDMoIpCfgPayloadFormat

determine TDM over IP proprietary
payload format.

Enumerationr/w

.1.3.6.1.4.1.164.14.1.3.1.3.1.3

pwTDMoIpCfgFarEndType

Determines TDM over IP Far End type.

Enumerationr/w

.1.3.6.1.4.1.164.14.1.3.1.3.1.4

pwTDMoIpCfgDelaySensitivity

Determines whether to optimize the clock
for accurateness or for constant delay:
o Disable (Accurate clock is more important than constant delay)
o Enable (Constant delay is more important than accurate clock).
…

Enumerationr/w

.1.3.6.1.4.1.164.14.1.3.1.3.1.5

pwTDMoIpCfgFramesInPacket

UDP payload length - determines the ethernet packet size

SNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.164.14.1.3.1.3.1.6

pwAtmCfgXTable

table

.1.3.6.1.4.1.164.14.1.3.2.1 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pwAtmCfgXTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pwAtmCfgXTable'

This table is an extension of pwAtmCfgTable
of PW-ATM-R-MIB. Each row that is added/removed there
will be added/removed in this table.

pwAtmCfgXEntry row .1.3.6.1.4.1.164.14.1.3.2.1.1

This table is indexed by pwIdx, the value of which is equal
to the same index that was created for the associated entry
in the PW Table (in the PW-STD-MIB)- the pwIndex.
An entry may be created by Agent in this table…

Indexes

No indexes recorded

Column	Syntax	OID
pwAtmCfgAal5Mode This objects defines whether AAL5 Mode is enabled for this PW.	Enumerationr/w	`.1.3.6.1.4.1.164.14.1.3.2.1.1.1`
pwAtmCfgAal5SduTermType This objects defines the AAL5-SDU Termination Type. It means - where should the AAL5-SDU PW frame, received from PSN, be forwarded: atm(2) - forwarded into ATM VCC. router(3) - forwarded into router. .	Enumerationr/w	`.1.3.6.1.4.1.164.14.1.3.2.1.1.2`
pwAtmCfgTimeout This object defines the Timeout period, measured in usec. Timeout mechanism is used in order to send out a packet before the maximum concatenated cells limit has been reached.	SNMPv2-SMIUnsigned32r/w Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.14.1.3.2.1.1.3`

pwFrCfgTable

table

.1.3.6.1.4.1.164.14.1.3.3.1 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pwFrCfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pwFrCfgTable'

This table contains a set of parameters for
Frame Relay PW in the pwFrTable.

pwFrCfgEntry row .1.3.6.1.4.1.164.14.1.3.3.1.1

These parameters define the characteristics of a
Frame Relay PW.
This table is indexed by pwIdx, the value of which is equal
to the same index that was created for the associated entry
in the PW Table (in the PW-STD-MI…

Indexes

No indexes recorded

Column	Syntax	OID
pwFrCfgDlciFieldLength DLCI Field length in bytes. Possible values ae 10, 17 or 24	Unsigned32r/w	`.1.3.6.1.4.1.164.14.1.3.3.1.1.1`
pwFrCfgBitMarking This object defines which Frame Relay bits are copied into the outgoing interface or from the incoming interface. When labeled bit is 1, FR bit is copied. For incoming FR bits - DE, FECN and BECN: DE - pwFrDeIncomingM…	Bitsr/w	`.1.3.6.1.4.1.164.14.1.3.3.1.1.2`
pwFrCfgDlci DLCI value of Frame Relay VC associated with this PW.	SNMPv2-SMIUnsigned32r/w Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.164.14.1.3.3.1.1.3`

pwPerfCurrentXTable

table

.1.3.6.1.4.1.164.14.2.1 · 1 row entry · 2 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pwPerfCurrentXTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pwPerfCurrentXTable'

This table is an extension of pwPerfCurrentTable (PW-STD-R-MIB).

pwPerfCurrentXEntry row .1.3.6.1.4.1.164.14.2.1.1

An entry in a table.

Indexes

No indexes recorded

Column	Syntax	OID
pwPerfCurrentInCongestDropPackets The counter for number of received packets that are dropped due to congestion by the PW (from the PSN) in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	`.1.3.6.1.4.1.164.14.2.1.1.1`
pwPerfCurrentOutCongestDropPackets The counter for number of transmitted packets that are dropped due to congestion by the PW (to the PSN) in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	`.1.3.6.1.4.1.164.14.2.1.1.2`

pwPerfIntervalXTable

table

.1.3.6.1.4.1.164.14.2.2 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pwPerfIntervalXTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pwPerfIntervalXTable'

This table is an extension of pwPerfIntervalTable (PW-STD-R-MIB).

pwPerfIntervalXEntry row .1.3.6.1.4.1.164.14.2.2.1

An entry in a table.

Indexes

No indexes recorded

Column	Syntax	OID
pwPerfIntervalXNumber A number N, between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified b…	Integer32	`.1.3.6.1.4.1.164.14.2.2.1.1`
pwPerfIntervalInCongestDropPackets The counter for number of received packets that are dropped due to congestion by the PW (to the PSN) during the interval.	PerfHist-TC-MIBPerfIntervalCount	`.1.3.6.1.4.1.164.14.2.2.1.2`
pwPerfIntervalOutCongestDropPackets The counter for number of transmitted packets that are dropped due to congestion by the PW (to the PSN) during the interval.	PerfHist-TC-MIBPerfIntervalCount	`.1.3.6.1.4.1.164.14.2.2.1.3`

pwAtmPerfCurrentXTable

table

.1.3.6.1.4.1.164.14.2.3 · 1 row entry · 3 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pwAtmPerfCurrentXTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pwAtmPerfCurrentXTable'

This table is an extension of pwArmPerfCurrentTable (PW-ATM-R-MIB).

pwAtmPerfCurrentXEntry row .1.3.6.1.4.1.164.14.2.3.1

An entry in a table.

Indexes

No indexes recorded

Column	Syntax	OID
pwAtmPerfCurrentInDiscardTotalCells The number of total received cells (CLP0 and CLP1) that were discarded by the traffic policer, in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	`.1.3.6.1.4.1.164.14.2.3.1.1`
pwAtmPerfCurrentInDiscardClp0Cells The number of received CLP0 cells that were discarded by the traffic policer, in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	`.1.3.6.1.4.1.164.14.2.3.1.2`
pwAtmPerfCurrentTaggedCells The number of cells that were tagged by the traffic policer from CLP=0 to CLP=1, in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	`.1.3.6.1.4.1.164.14.2.3.1.3`

pwAtmPerfIntervalXTable

table

.1.3.6.1.4.1.164.14.2.4 · 1 row entry · 4 columns

Open in standard view

Uses the rad variant from /opt/observium/mibs/rad.

Command help

Walk pwAtmPerfIntervalXTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-MIB::pwAtmPerfIntervalXTable'

This table is an extension of pwAtmPerfIntervalTable (PW-ATM-R-MIB).

pwAtmPerfIntervalXEntry row .1.3.6.1.4.1.164.14.2.4.1

An entry in a table.

Indexes

No indexes recorded

Column	Syntax	OID
pwAtmPerfIntervalXNumber A number N, between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified b…	Integer32	`.1.3.6.1.4.1.164.14.2.4.1.1`
pwAtmPerfIntervalInDiscardTotalCells The number of total received cells (CLP0 and CLP1) that were discarded by the traffic policer, during the interval.	PerfHist-TC-MIBPerfIntervalCount	`.1.3.6.1.4.1.164.14.2.4.1.2`
pwAtmPerfIntervalInDiscardClp0Cells The number of received CLP0 cells that were discarded by the traffic policer, during the interval.	PerfHist-TC-MIBPerfIntervalCount	`.1.3.6.1.4.1.164.14.2.4.1.3`
pwAtmPerfIntervalTaggedCells The number of cells that were tagged by the traffic policer from CLP=0 to CLP=1, during the interval.	PerfHist-TC-MIBPerfIntervalCount	`.1.3.6.1.4.1.164.14.2.4.1.4`