RAD-GEN-MIB Table View

This table traces the agent fatal error.

resetInformationEntry row .1.3.6.1.4.1.164.6.1.16.1.1.1

This table has a single row entry and provides
Information related to the last reboot.

Indexes

resetInformationId

Column	Syntax	OID
resetInformationId resetInformationId =1	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.1.16.1.1.1.1
resetInformationLastReset Type of last reset.	Enumeration Enumerated Values: 1 coldStart 2 warmStart	.1.3.6.1.4.1.164.6.1.16.1.1.1.2
resetInformationFileName If the filename is empty then the object is not applicable	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.164.6.1.16.1.1.1.3
resetInformationLineNumber if the line number value is zero then this object is not applicable	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.1.16.1.1.1.4
resetInformationPC if the Program Counter value is zero then this object is not applicable	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.1.16.1.1.1.5
resetInformationExceptionCause if the Exception Cause value is zero then this object is not applicable	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.1.16.1.1.1.6
resetInformationReason Reason for the last reset.	Enumeration Enumerated Values: 1 resetCommand 2 factoryDefaultCommand 3 userDefaultCommand 4 factoryDefaultAllCommand 5 softwareInstallation 6 unconfirmedStartupConfig 7 unconfirmedSoftware 8 configurationFileRejection 9 resetAwaitingStartupConfigConfirm 10 resetAwaitingSoftwareConfirm 11 configLoadedByZeroTouch 255 otherReason	.1.3.6.1.4.1.164.6.1.16.1.1.1.7

This table indicates  the destination address of the traps.
Internally it will be limited to ten addresses.

mngEntry row .1.3.6.1.4.1.164.6.2.7.1

An entry in table.

Indexes

mngID

Column	Syntax	OID
mngID This value indicates an index of a specific IP address	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.7.1.1
mngIP This value indicates the destination address of the traps. IP 0.0.0.0 removes the entry.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.164.6.2.7.1.2
mngIPMaskdeprecated This value indicates the mask of the destination addresses of the traps.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.164.6.2.7.1.3
mngTrapMask The value of this attribute determines the type of traps the agent should mask and not send to this NMS. The value is differently determined for different products. There are mainly two methods: - an integer number, …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.7.1.4
mngAlarmTrapMask The value of this object determines the alarm traps that the agent should mask (not send to this manager). The value is an Octet String, where each bit is assigned to a certain trap. If the bit = 1, the trap will be…	OctetStringr/w	.1.3.6.1.4.1.164.6.2.7.1.5
mngSnmpTrapUdpPort This variable enables to set the UDP port (socket) used for SNMP traps.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.7.1.6

This table may include the last few traps generated by the agent, for future retrieval. The table
has a limited capacity. If traps are not retrieved in proper time, they will be
over-written by new traps.
For other devices, it can include generic variables that will be attached to traps
as 'accessible-for-notify'.

trapEntry row .1.3.6.1.4.1.164.6.2.11.1

An entry in trapTable.

Indexes

trapID

Column	Syntax	OID
trapID This object indicates an index of a specific trap. Can be used also for any trap, while trapVal is used as 'accessible-for-notify' or trapNumeric is used.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.11.1.1
trapVal This object is the actual ASCII description of the trap. It can be used also as attached variable of traps, in order to detail in explicit ASCII text, data of the trap. In this case, it is used as 'accessible-for-notif…	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.164.6.2.11.1.2
trapTimeSinceOccurrence This object indicates the amount of time passed since the occurrence of the event that triggered this trap.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.11.1.3
trapNumeric This object is a numeric general parameter, that can be attached to any trap. Values can be positive or negative.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.11.1.4

This parameters table is for 
internal Software down load. It also includes data 
about all files contained in the Object from which 
down-load is performed.

intSwdlEntry row .1.3.6.1.4.1.164.6.2.12.10.1

An entry in table.

Indexes

intSwdlObjIdx intSwdlFileIdx

Column	Syntax	OID
intSwdlObjIdx The index of the object from which down-load is performed.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.12.10.1.1
intSwdlFileIdx The index of the files included in intSwdlObjIdx. One of these files can be selected to be internally downloaded.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.12.10.1.2
intSwdlFileName The name of the file.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.164.6.2.12.10.1.3
intSwdlFileSwVer The software version of the file.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.164.6.2.12.10.1.4
intSwdlSwDate The software version date of the file.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.164.6.2.12.10.1.5
intSwdlSize The size of the file.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.164.6.2.12.10.1.6
intSwdlCmd The command to down-load a SW file to an object. The Agent will change the value of this MIB object to off(2) automatically, after accepting the command.	Enumerationr/w Enumerated Values: 1 notApplicable 2 off 3 on	.1.3.6.1.4.1.164.6.2.12.10.1.7
intSwdlToSubSystem This object defines the subsystem for download. Bit='1'- APPLY to respective sub system. Bit='0'- DO NOT APPLY to respective sub system. For more details see product specification. For every octet bit0=LSB, bit7=MSB	OctetStringr/w	.1.3.6.1.4.1.164.6.2.12.10.1.8
intSwdlCardType This object defines the Card type that this file is relevant for.	Enumeration Enumerated Values: 1 unknown 220 gstm1 221 goc3 222 gstm1D 223 goc3D 270 serverE1 271 serverT1 272 serverE1Pw 273 serverT1Pw 280 gigabitEth 281 gigabitEth2 282 eth2 283 gigabitEth8 284 eth8 290 channelizedT3Pw1 300 cesT128 301 cesE128 302 cesT1Pw28 303 cesE1Pw28 310 vmxE1VeDe 311 vmxE1VeDi 312 vmxE1ViDe 313 vmxE1ViDi 314 vmxT1VeDe 315 vmxT1VeDi 316 vmxT1ViDe 317 vmxT1ViDi 318 vc12E1UeNe 319 vc12E1UeNi 320 vc12E1UiNe 321 vc12E1UiNi 322 vc12T1UeNe 323 vc12T1UeNi 324 vc12T1UiNe 325 vc12T1UiNi 326 vca16E1UeNe 327 vca16E1UeNi 328 vca16E1UiNe 329 vca16E1UiNi 330 vca16T1UeNe 331 vca16T1UeNi 332 vca16T1UiNe 333 vca16T1UiNi 334 vca12E1UeNe 335 vca12E1UeNi 336 vca12E1UiNe 337 vca12E1UiNi 338 vca12T1UeNe 339 vca12T1UeNi 340 vca12T1UiNe 341 vca12T1UiNi 342 vmg16E1Ue 343 vmg16E1Ui 344 vmg16T1Ue 345 vmg16T1Ui 346 vmg12E1Ue 347 vmg12E1Ui 348 vmg12T1Ue 349 vmg12T1Ui	.1.3.6.1.4.1.164.6.2.12.10.1.9
intSwdlFlashIdx The index of the flash memory this file is stored in (1 or 2) (Example: 1= The file is stored in flash No.1). ASMi52 file will always be stored in Flash No.2 (intSwdlFlashIdx=2).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.12.10.1.10

This parameters table is for software download status. 
It also includes data about the files down-loaded or 
attempted to be down-loaded.

swdlStatusEntry row .1.3.6.1.4.1.164.6.2.12.11.1

An entry in table.

Indexes

swdlStatusTypeIdx swdlStatusIdx

Column	Syntax	OID
swdlStatusTypeIdx The index of the down-load type (e.g. external (1) or internal (2)).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.12.11.1.1
swdlStatusIdx The index of the status rows.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.12.11.1.2
swdlStatusFileName The name of the file.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.164.6.2.12.11.1.3
swdlStatusSlot The slot of the updated (or attempted to be updated) object.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.164.6.2.12.11.1.4
swdlStatusSubSystem The subsystem that updated (or attempted to be updated).	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.164.6.2.12.11.1.5
swdlStatusStatus The status of the down load process. Value: Fail (2), OK (3), InProcess (4).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.12.11.1.6
swdlStatusTime This MIB parameter indicates the time SW download was finished. The format shuld be YYYY-MM-DD, hh:mm:ss	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.164.6.2.12.11.1.7

Scheduling configuration table for 
Agent initiated file transfer.

autoFileTransferEntry row .1.3.6.1.4.1.164.6.2.12.13.1.1

An entry in the table.

Indexes

autoFileTransferType

Column	Syntax	OID
autoFileTransferType This object defines the type of file to be transferred by agent.	Enumeration Enumerated Values: 1 alarmsBuffer	.1.3.6.1.4.1.164.6.2.12.13.1.1.1
autoFileTransferServerIp This object defines the IP Address of the server to which the file is uploaded.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.164.6.2.12.13.1.1.2
autoFileTransferFileName This object defines the name of the file to be uploaded.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.164.6.2.12.13.1.1.3
autoFileTransferScheduling This object defines schedule for TFTP Automatic session(s) initiated by Agent, according to the value selected: now - initiate immediate single session. recurrence- initiate single session 'eve…	Enumerationr/w Enumerated Values: 1 notApplicable 2 now 3 recurrence	.1.3.6.1.4.1.164.6.2.12.13.1.1.4
autoFileTransferTimeRecurrence This object defines time reccurence interval, e.g. M can be 'every M days', 'every M hours' etc. Zero is used to indicate there's no time reccurence (0= notApplicable). This object is taken into account only if autoF…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.12.13.1.1.5
autoFileTransferOccurrenceRecurrence This object defines Occurrence reccurence interval, e.g N can be in 'every N alarms', 'every N log entries' etc. zero is used to indicate There's no Event Reccurence. (0= notApplicable) This object is taken into acco…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.12.13.1.1.6

This table contains parameters for each NTP Server.
Entries in the table can be dynamically created.
The entries created by user via sntpServerRowStatus, can also be
changed or removed.
The table may include also Broadcast Servers, when Broadcast
Client Mode is enabled. These are Servers from which the device
received timestamp by Broadcast. Their entries are automatically
created by the device. Entries of these Servers cannot
be changed or removed.

sntpServerEntry row .1.3.6.1.4.1.164.6.2.14.4.11.1

An entry in the NTP Server table.

Indexes

sntpServerID

Column	Syntax	OID
sntpServerID The number (index) of the NTP Server.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.14.4.11.1.1
sntpServerRowStatus This object enables creation and deletion of entries in the sntpServerTable.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.164.6.2.14.4.11.1.2
sntpServerAddressType Server Address type, indicating IPv4(1) or IPv6(2).	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.164.6.2.14.4.11.1.3
sntpServerAddress IP Address of the NTP Server.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.164.6.2.14.4.11.1.4
sntpServerPort Source UDP port of the device for sending requests to a configured NTP Server.	INET-ADDRESS-MIBInetPortNumberr/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.164.6.2.14.4.11.1.5
sntpServerPreference This object marks the Preferred Server. 1 = Preferred (only one Server can have this value) 2 - Not Preferred.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.14.4.11.1.6
sntpServerAdminStatus Administrative Status of the NTP Server.	Enumerationr/w Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.164.6.2.14.4.11.1.7
sntpServerType Type of the NTP Server.	Enumeration Enumerated Values: 1 unicast 2 broadcast	.1.3.6.1.4.1.164.6.2.14.4.11.1.8
sntpServerLastReceivedTimestamp Last received Date and Time from the NTP Server, according to UTC Time. 0000 0000 = Not Applicable.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.164.6.2.14.4.11.1.9
sntpServerLastReceivedStratum Last received Stratum from the NTP Server. 0xFFFFFFFF = Not Applicable.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.14.4.11.1.10
sntpServerTimeSinceLastReceivedMessage Time passed since last received message from the NTP Server.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.14.4.11.1.11
sntpServerSendRequestNow Upon setting this parameter to 'on', an immediate request should be sent to the specified NTP Server. After sending the request, the value 'off' will be resumed. No action when setting this parameter to 'off'	Enumerationr/w Enumerated Values: 2 off 3 on	.1.3.6.1.4.1.164.6.2.14.4.11.1.12

An Augment to the Schedule table
(schedTable in DISMAN-SCHEDULE-MIB; RFC-3231).

schedXEntry row .1.3.6.1.4.1.164.6.2.14.5.1

An entry in the table.

Indexes

No indexes recorded

Column	Syntax	OID
schedYear The year during which the scheduled action should take place.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.14.5.1.1
schedWeekInMonth The week in month (schedMonth) during which the scheduled action should take place.	Enumerationr/w Enumerated Values: 1 first 2 second 3 third 4 fourth 5 last	.1.3.6.1.4.1.164.6.2.14.5.1.2
schedParam A Parameter that might be used whenever the scheduled action takes place. For summer-time schedule - This variable represents the time offset (in minutes), meaning: the number of minutes that should be ad…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.14.5.1.3
schedXWeek The set of weeks within a month (schedMonth) during which the scheduled action should take place.	Bitsr/w Enumerated Values: 0 first 1 second 2 third 3 fourth 4 fifth 5 last	.1.3.6.1.4.1.164.6.2.14.5.1.4
schedAction The action that should take place when the schedule is executed. By default it is '60' for summer time start, and empty string otherwise.	OctetStringr/w Constraints: range: 0-1024	.1.3.6.1.4.1.164.6.2.14.5.1.5

This table includes the connector type of ports or interfaces.

physicalConnectorEntry row .1.3.6.1.4.1.164.6.2.15.1.1

An entry in table.

Indexes

portIdx

Column	Syntax	OID
portIdx This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.1.1.1
physicalConnector The connector of the port/interface. other - none of the specified connectors none - no connector.	Enumeration Enumerated Values: 1 other 2 v35 3 rs530 4 x21 5 bnc 6 utp 7 aui 8 rs422 9 crossUtp 10 rj45 11 v24 12 g703 13 termBlock3AndRj45 14 terminalBlock3 15 terminalBlock5 16 terminalBlock7 17 db25 18 db15 19 rj45ethernet 20 termBlock5AndRj45 21 db9 22 g703E1 23 g703E1-LTU 24 sc 25 st 26 stl 27 fc 28 tb5w 29 termBlock6AndRj45 30 ethBnc 31 scsi26 32 eth4381 33 twoBnc 34 scsi50 35 twoMiniBnc 36 sf1 37 terminalBlock4 38 sf2 39 db25Balanced 40 v36 41 block4W 42 iripRj45 43 irEthQRj45 44 iripBnc 45 rs530WA 46 v35WA 47 irEthQBnc 48 v35Db25 49 rj11 50 mtrj 51 lc 52 terminalBlock2 53 irEth10s100 54 scsi68 55 sf3 56 fcLH 57 telco50 58 telco64 59 irEthQN 60 terminalBlock6 61 scLH 62 stLH 63 lcLH 64 sfpIn 65 sfpOut 66 db44 67 db62 68 v24Db9 69 scsi40 70 sf1NineRow 71 sf2NineRow 72 sf3NineRow 73 smartSerial26 74 miniUsb5 75 db26 76 comboUtpSfpIn 77 comboUtpSfpOut 78 hiDensity160Pin 79 xfpIn 80 xfpOut 81 ssfpIn 82 ssfpOut 83 comboUtpSsfpIn 84 comboUtpSsfpOut 85 scsi68DS 86 miniBnc 87 sMA 88 rj45Shdsl8w 89 miniBncAndRj45 90 sfpPlusIn 91 sfpPlusOut 255 none	.1.3.6.1.4.1.164.6.2.15.1.1.2
portOptWaveLength Wave Length of an Optical interface/port in [nm] and specification if Laser or not. notApplicable - for non-optical ports.	Enumeration Enumerated Values: 1 notApplicable 2 nm850 3 nm1310 4 nm1310Laser 5 nm1550Laser 6 nm1470Laser 7 nm1490Laser 8 nm1510Laser 9 nm1530Laser 10 nm1570Laser 11 nm1590Laser 12 nm1610Laser 13 nm1330Laser 14 nm1270Laser	.1.3.6.1.4.1.164.6.2.15.1.1.3
portOptMode Laser Mode of an Optical Laser interface/port. notApplicable - for non-Laser ports.	Enumeration Enumerated Values: 1 notApplicable 2 singleMode 3 multiMode	.1.3.6.1.4.1.164.6.2.15.1.1.4
portBalance This object is according to the port Impedance. For T1 - always balanced. For E1 - there are different impedance values for balanced and unbalanced.	Enumerationr/w Enumerated Values: 1 notApplicable 2 unbalanced 3 balanced	.1.3.6.1.4.1.164.6.2.15.1.1.5
portDdmSupport SFP (Small Form Pluggable) port -support Digital Diagnostics Monitoring.	Enumeration Enumerated Values: 1 notApplicable 2 no 3 yes	.1.3.6.1.4.1.164.6.2.15.1.1.6
portMfgName (SFP) Port Manufacturer name (Maximum - 16 characters).	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.164.6.2.15.1.1.7
portTypicalMaxRange Maximum range supported by SFP port, in meter units.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.15.1.1.8
physicalConnectorString (SFP) connector type. It can be Vendor Specific (unknown in advance). Being a string, the object is not affected by any future new connectors. This object will usually not be used for drawing the connector.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.164.6.2.15.1.1.9
portVendorPartNo SFP Vendor Part Number. Being a string, the object is not affected by any future new SFPs.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.164.6.2.15.1.1.10
physicalConnectorUsed This object is relevant only when the value of physicalConnector is comboUtpSfpIn(76) or comboUtpSfpOut(77). sfpOrRj45 - (default value) If SFP is inserted (In), SFP is used (RJ45 is not used (shut)). …	Enumerationr/w Enumerated Values: 1 notApplicable 2 sfpOrRj45 3 sfpOnly 4 rj45Only	.1.3.6.1.4.1.164.6.2.15.1.1.11
physicalConnectorSfpWaveLength Wavelength of a fiber optic SFP/XFP in units of hundredths of nm. The value zero is returned for non-optical ports.	hundredths of nmSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.15.1.1.18

A table.

prtSpEntry row .1.3.6.1.4.1.164.6.2.15.2.1.1

Supervisory port parameter table.

Indexes

prtSupervisoryIndex

Column	Syntax	OID
prtSupervisoryIndex The SP port index. For some products, having modules (cards): The LS byte of the integer is the port index 1..255. The MS byte is different than 0 only if the port belongs to a module. In that case it is the module n…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.2.1.1.1
prtSupervisoryRate This attribute indicates the operation rate (speed) of the port. auto - automatic rate selection, by the agent.	Enumerationr/w Enumerated Values: 1 auto 2 s300bps 3 s1200bps 4 s2400bps 5 s4800bps 6 s9600bps 7 s19200bps 8 s38400bps 9 s57600bps 10 s115200bps	.1.3.6.1.4.1.164.6.2.15.2.1.1.2
prtSupervisoryDataBits This attribute indicates the number of data bits in an async frame	Enumerationr/w Enumerated Values: 1 dataBits7 2 dataBits8	.1.3.6.1.4.1.164.6.2.15.2.1.1.3
prtSupervisoryParity This attribute indicates the parity mode in an async frame	Enumerationr/w Enumerated Values: 1 none 2 odd 3 even	.1.3.6.1.4.1.164.6.2.15.2.1.1.4
prtSupervisoryStopBits This attribute indicates the parity mode in an async frame.	Enumerationr/w Enumerated Values: 1 notApplicable 2 stopBits1 3 stopBits1dot5 4 stopBits2	.1.3.6.1.4.1.164.6.2.15.2.1.1.5
prtSupervisoryUsage This attribute indicates the usage of the SP port.	Enumerationr/w Enumerated Values: 1 unknown 2 noUse 3 terminal 4 nmsSlip 5 nmsPpp 6 muxSlip 7 muxPpp 8 dialOut	.1.3.6.1.4.1.164.6.2.15.2.1.1.6
prtSupervisoryInterface This attribute indicates the supervisory port interface.	Enumerationr/w Enumerated Values: 1 notApplicable 2 dce 3 dte	.1.3.6.1.4.1.164.6.2.15.2.1.1.7
prtSupervisoryCTS CTS line state.	Enumerationr/w Enumerated Values: 1 notApplicable 2 on 3 rts 4 dteWait 5 dteIgnore	.1.3.6.1.4.1.164.6.2.15.2.1.1.8
prtSupervisoryDcdDelay DCD delay in msec.	Enumerationr/w Enumerated Values: 1 notApplicable 2 d0 3 d10 4 d50 5 d100 6 d200 7 d300	.1.3.6.1.4.1.164.6.2.15.2.1.1.9
prtSupervisoryDSR DSR line state.	Enumerationr/w Enumerated Values: 1 notApplicable 2 on 3 dtr	.1.3.6.1.4.1.164.6.2.15.2.1.1.10
prtSupervisoryRoutProtocol This attribute indicates the routing protocol of the port. notApplicable - for DP.	Enumerationr/w Enumerated Values: 1 notApplicable 2 none 3 proprietary 4 rip2	.1.3.6.1.4.1.164.6.2.15.2.1.1.11

This table includes G.826 ports or interfaces.

prtPerfEntry row .1.3.6.1.4.1.164.6.2.15.3.1.1

An entry in table.

Indexes

prtPerfIdx prtPerfPeriodRef

Column	Syntax	OID
prtPerfIdx This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.3.1.1.1
prtPerfPeriodRef This object is an index that specifies which period of time, the next 5 objects refer to. currentPeriod - the period since last prtPerfSaveAndResetCmd received or since Start-up (if no prtPerfSaveAndResetCmd w…	Enumeration Enumerated Values: 1 currentPeriod 2 lastPeriod	.1.3.6.1.4.1.164.6.2.15.3.1.1.2
prtPerfElapsedTime Elapsed Time in seconds. - for prtPerfPeriodRef=currentPeriod: The period since last prtPerfSaveAndResetCmd received or since Start-up (if no prtPerfSaveAndResetCmd was received since Start-up) until now. - for prt…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.3.1.1.3
prtPerfUAS Number of Unavailable Seconds for the reference period (prtPerfPeriodRef).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.3.1.1.4
prtPerfES Number of Errored Seconds for the reference period (prtPerfPeriodRef).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.3.1.1.5
prtPerfSES Number of Severely Errored Seconds for the reference period (prtPerfPeriodRef).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.3.1.1.6
prtPerfBBE Number of Background Block (or Frame) Errors for the reference period (prtPerfPeriodRef).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.3.1.1.7
prtPerfBlocksPerSec Blocks per second (or frames per second) of the port/interface indicated by portIdx. This object is constant for a certain port/interface. It is not affected by the prtPerfPeriodRef index.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.3.1.1.8
prtPerfTimeTag Time Tag of Last Period: sysUpTime when last prtPerfSaveAndResetCmd was executed. This object is applicable only for prtPerfPeriodRef=lastPeriod. For prtPerfPeriodRef=currentPeriod, the value will always be 0.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.15.3.1.1.9
prtPerfSaveAndResetCmd A command per port/interface, to Save data of Current Period in Last Period data-set and start a new counting period for Current Period. This object is applicable only for prtPerfPeriodRef=currentPeriod. Setting this ob…	Enumerationr/w Enumerated Values: 2 off 3 on	.1.3.6.1.4.1.164.6.2.15.3.1.1.10

This table includes test data for ports or interfaces.

prtTestEntry row .1.3.6.1.4.1.164.6.2.15.4.1.1

An entry in table.

Indexes

prtTestIdx

Column	Syntax	OID
prtTestIdx This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.4.1.1.1
prtTestCmdAndStatus Setting this object to a value as detailed further on (except 0) will initiate a test on the specific port. The test/s requested will be set according to the respective bit. The value of this object will be a sum of (2*…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.4.1.1.2
prtBertCounter This object indicates the number of BERT errors encountered during the BERT operation. It is valid only when BERT (Bit Error Rate Test) is active on the specific port. The Counter starts from zero (0) anytime BERT is i…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.4.1.1.3
prtTestInitiator This object indicates who initiated this port's test/s.	Enumeration Enumerated Values: 1 unknown 2 user 3 remoteUnit 4 dteRouter	.1.3.6.1.4.1.164.6.2.15.4.1.1.4
prtTestTimeout This object is applicable only when a single test is running. It indicates the test activation timeout in minutes. For RICi-E1T1, RICi-E3T3 and LRS-16, the measurement unit is in seconds. When the timeout expires, the t…	Integer32r/w Constraints: range: 0-86400	.1.3.6.1.4.1.164.6.2.15.4.1.1.5
prtTestVctRxResult This object indicates the result of the Vct on the cable connected to the RX connector.	Enumeration Enumerated Values: 1 notApplicable 2 fail 3 normal 4 open 5 short 6 shortToCrossPair 7 coupleWithCrossPair	.1.3.6.1.4.1.164.6.2.15.4.1.1.6
prtTestVctTxResult This object indicates the result of the Vct on the cable connected to the TX connector.	Enumeration Enumerated Values: 1 notApplicable 2 fail 3 normal 4 open 5 short 6 shortToCrossPair 7 coupleWithCrossPair	.1.3.6.1.4.1.164.6.2.15.4.1.1.7
prtTestVctRxDistance This object indicates the distance in Meters to the RX cable Open/ Short location discovered by the Vct. This parameter is applicable for Vct Result = Normal or Fail only, Else the value of this parameter will be equa…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.4.1.1.8
prtTestVctTxDistance This object indicates the distance in Meters to the TX cable Open/ Short location discovered by the Vct. This parameter is applicable for Vct Result = Normal or Fail only, Else the value of this parameter will be equa…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.4.1.1.9
prtTestVctCmd Vct command. on (3) = Start Vct on both cables connected to RX and TX connectors of this port. Agent will perform the required command and change automatically the value of this object to off(2).	Enumerationr/w Enumerated Values: 2 off 3 on	.1.3.6.1.4.1.164.6.2.15.4.1.1.10
prtTestVctRxCrossPair This object should be equal to the Index (prtTestIdx) of the Rx cross pair. This object is applicable only for Vct Result = shortToCrossPair or coupleWithCrossPair. This object was especially created for ETX-202. Curre…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.4.1.1.11
prtTestVctTxCrossPair This object should be equal to the Index (prtTestIdx) of the Tx cross pair. This object is applicable only for Vct Result = shortToCrossPair or coupleWithCrossPair.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.4.1.1.12
prtTestActivationDelay This object is applicable only when a single test is running. It indicates test activation delay in seconds. A Value of 0 indicates that the test starts immediately.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.15.4.1.1.13
prtTestMacSwapLoopDataMode This object defines which part of the data will be looped back.	Enumerationr/w Enumerated Values: 1 all 2 allExceptMng 3 specificVlan	.1.3.6.1.4.1.164.6.2.15.4.1.1.14
prtTestMacSwapLoopVlanId This object specifies the VLAN ID for prtTestMacSwapLoopDataMode=specificVlan.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.4.1.1.15
prtTestMacSwapLoopDirection This object defines the direction of the performed loopback. In ETX102 'local' corresponds to Ingress loop (either on User port or on Network port), and 'remote' corresponds to Egress loop (either on User port or on Net…	Enumerationr/w Enumerated Values: 2 local 3 remote	.1.3.6.1.4.1.164.6.2.15.4.1.1.16
prtTestMacSwapLoopDestAddr Configures the MAC address that will be sent in the Destination field of the packet in the outgoing direction.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.164.6.2.15.4.1.1.17
prtTestMacSwapLoopSrcAddr Configures the MAC address that will be sent in the Source field of the packet in the outgoing direction.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.164.6.2.15.4.1.1.18
prtTestOamMinRoundTripDelay The mininal value of round trip delay of loopback message for a session of OAM loopback.Units are msec.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.15.4.1.1.19
prtTestOamMaxRoundTripDelay The maximum value of round trip delay of loopback message for a session of OAM loopback.Units are msec.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.15.4.1.1.20
prtTestOamAvgRoundTripDelay The average round trip delay of loopback message for a session of OAM loopback.Units are msec.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.15.4.1.1.21
prtTestOamTxInterval Indicates the interval between loopback sent messages.Units are msec.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.15.4.1.1.22
prtTestDestinationIpAddress Indicates the destination IP Address in the transmitted messages that are looped back.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.164.6.2.15.4.1.1.23
prtTestForceTTL Time-to-live.Number of hops the loopback message will go through the net before deciding to discard it.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.15.4.1.1.24
prtTestBwProfiledeprecated Indicates the BW profile (from bwProfileTable) that is assigned to the loopback test in order to limit the traffic that is looped back.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.15.4.1.1.25
prtTestSourceIpAddress Indicates the source IP Address in the transmitted messages that are looped back.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.164.6.2.15.4.1.1.26
prtTestRemainTime Indicates the remain time for test activation in seconds.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.15.4.1.1.27

This table includes general port parameters. The meaning is
different for every product that supports it due to a general
parameter - prtControlCnfg.
          
For ACE2002:
-This table is used as a mechanism to create the next interface index.
 The algorithm description:
 The NMS will send the agent the following get command: get(nextIfIndex.index),
 where index=interface on which the new index is dependent on.
 Upon this command the agent will generate and return the new index to the NMS.
- This table is partially supported according to the interface type.
  Upon getNext function the irrelevant parameters will be skipped.

prtParamEntry row .1.3.6.1.4.1.164.6.2.15.5.1.1

An entry in table.

Indexes

prtParamIdx

Column	Syntax	OID
prtParamIdx This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used. For ACE2002: This parameter is the …	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.5.1.1.1
prtControlCnfg This object may be used for port RW general parameter/s. For detailed meaning, see product's spec. Supported by: PRBi-E3/T3. For ACE2002: This parameter will include the value of the new index generated …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.5.1.1.2
prtParamClkSrc The source of Transmit Clock. 'loopTiming' or 'loopback' indicates that the recovered receive clock is used as the transmit clock. 'localTiming' or 'internal' indicates that a local clock source is used…	Enumerationr/w Enumerated Values: 1 loopTiming 2 localTiming 3 throughTiming 4 adaptive 5 master 6 fallback 7 station 8 system 255 notApplicable	.1.3.6.1.4.1.164.6.2.15.5.1.1.3
prtParamPhantom Power feeding to another device.	Enumerationr/w Enumerated Values: 1 notApplicable 2 disable 3 enable	.1.3.6.1.4.1.164.6.2.15.5.1.1.4
prtParamResetStatsCmd on (3) - Reset all statistics of the selected port. lacp (4) - Reset LACP statistics of the selected port. l2cp (5) - Reset L2CP statistics of the selected port. elmi (6) - Reset ELMI statistics…	Enumerationr/w Enumerated Values: 2 off 3 on 4 lacp 5 l2cp 6 elmi 7 optPrtMonitor 8 interval 9 day 10 efm 11 lldp	.1.3.6.1.4.1.164.6.2.15.5.1.1.5
prtParamLastResetStatsTime The value of MIB II's sysUpTime object at the last time that prtParamResetStatsCmd was Set to on(3) for this port. If prtParamResetStatsCmd was never Set to on(3) since last re-initialization of the agent, then this…	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.164.6.2.15.5.1.1.6
prtParamInterfaceType The interface type of the port, or the frequency used as clock reference. Clock reference values may be either e1(2) or t1(3), gps (18) or wave with the specified frequency: f1544kHz(15), f2048kHz(16) or f64kHz (17). f1…	Enumerationr/w Enumerated Values: 1 notApplicable 2 e1 3 t1 4 fr 5 hdlc 6 hdsl2 7 shdsl 8 adsl 9 adsl2 10 reAdsl2 11 mPair 12 efm 13 atmIma 14 ds1 15 f1544kHz 16 f2048kHz 17 f64kHz 18 gps 19 j1 20 ethernet 21 svi 22 logicalMac 23 lag 24 sag 25 sap 26 etpTransport 27 etpSubscriber 28 r1pps 29 miniBnc 30 e3 31 t3 32 sonetSdh 33 ds1Opt 34 tdmBridge	.1.3.6.1.4.1.164.6.2.15.5.1.1.7
prtParamClearAlarm Setting this attribute to ON, will enforce a clear operation on the Port Alarms. Upon completion, the value will automatically change to off(2).	Enumerationr/w Enumerated Values: 2 off 3 on	.1.3.6.1.4.1.164.6.2.15.5.1.1.8
prtParamLeds This entry specifies the LEDs status of the port. Each led is represented by 4 bits where the first 2 bits (left) specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) specify the color :…	OctetString	.1.3.6.1.4.1.164.6.2.15.5.1.1.9
prtParamLineLength Line Length of the line connected to this port.	Enumerationr/w Enumerated Values: 1 notApplicable 2 long 3 normal 4 short	.1.3.6.1.4.1.164.6.2.15.5.1.1.10
prtParamUsage Defines whether this port works as User port or as Network port.	Enumerationr/w Enumerated Values: 1 notApplicable 2 user 3 network	.1.3.6.1.4.1.164.6.2.15.5.1.1.11
prtParamMappingMode This object defines path protection on SONET/SDH link Auto - SONET/SDH mapping for port is copied automatically to same TU on the redundant SONET/SDH local (reside on same slot) link by agent. Manual - the user can con…	Enumerationr/w Enumerated Values: 1 notApplicable 2 off 3 auto 4 manual 5 adjacent	.1.3.6.1.4.1.164.6.2.15.5.1.1.12
prtParamAlarmIndication This object indicates status-aggregation of non-masked alarms associated with all interface layers, related to this physical port. When at least one non-masked alarm exists on any layer, value of this object is on (3)…	Enumeration Enumerated Values: 1 notApplicable 2 off 3 on	.1.3.6.1.4.1.164.6.2.15.5.1.1.13
prtParamClkQualityLevel This parameter indicates quality level of clock signal. Quality is encoded according to SSM (Synchronization Status Messages) encoding. Bits 8 -5 of byte are encoded as follows (when bit1=0): Left most bit - M…	OctetString Constraints: range: 1-1	.1.3.6.1.4.1.164.6.2.15.5.1.1.14
prtParamClkWaveShape Wave shape of station clock source signal. This parameter is applicable only when prtParamInterfaceType value is one of the following: f1544kHz(15), f2048kHz(16).	Enumerationr/w Enumerated Values: 1 notApplicable 2 sine 3 square	.1.3.6.1.4.1.164.6.2.15.5.1.1.15
prtParamStatus Station clock source Status.	Enumeration Enumerated Values: 1 notApplicable 2 up 3 signalLoss 4 syncLoss	.1.3.6.1.4.1.164.6.2.15.5.1.1.16
prtParamSignalLevel This object indicates signal level (in thenth of dB units) on selected port.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.5.1.1.17
prtParamClkUserQualityLevel This parameter allows user to mark quality level of clock. Quality is encoded according to SSM (Synchronization Status Messages) encoding. Bits 8 -5 of byte are encoded as follows: Left most bit - MSB(8) ---> LSB(5) 8…	OctetStringr/w Constraints: range: 1-1	.1.3.6.1.4.1.164.6.2.15.5.1.1.18
prtParamDataRate Rate of serial data port (V.11, V.24, V.35) in kbps units.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.15.5.1.1.19
prtParamLoopDetect Enable/disable Loop Detection on a port. Examples of ports: physical, Channelized Bundle over TDM Uplink, Bridge Ports.	Enumerationr/w Enumerated Values: 2 disable 3 enable	.1.3.6.1.4.1.164.6.2.15.5.1.1.20
prtParamActUponLoopDetect This parameter is used to indicate which actions should be taken in case a loop is detected in the network the port is part of. Each action is represented by a bit. Currently defined (for RIC155GE/RIC622GE): Bit 0 - Tra…	OctetStringr/w	.1.3.6.1.4.1.164.6.2.15.5.1.1.21
prtParamPSNLayer This object indicates the network layer from which clock is derived.	Enumerationr/w Enumerated Values: 2 l2 3 l3	.1.3.6.1.4.1.164.6.2.15.5.1.1.22
prtParamRxSsm This object indicates if Station Clock SSM messages received will serve as criteria for clock selection.	Enumerationr/w Enumerated Values: 2 disabled 3 rx	.1.3.6.1.4.1.164.6.2.15.5.1.1.23
prtParamClkSsmRxSource This object indicates the Sa-bit of the E1 frame, in which SSM messages are carried.	Enumerationr/w Enumerated Values: 2 sa4 3 sa5 4 sa6 5 sa7 6 sa8	.1.3.6.1.4.1.164.6.2.15.5.1.1.24
prtParamFarEndDevice Programmed Far-End device connected to this port. This object is relevant for products having multiple DBs. It will enable configuring offline, the relevant data. For MP-4100, LRS-102 OP-108/106 cards, the options w…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.15.5.1.1.26
prtParamTxClk enable/disable station clock signal output.	Enumerationr/w Enumerated Values: 1 notApplicable 2 disable 3 enable	.1.3.6.1.4.1.164.6.2.15.5.1.1.27
prtParamSdBerThreshold The Signal Degrade Bit Error Rate Threshold. The negated value of this number is used as the exponent of 10 for computing the threshold value for the Bit Error Rate (BER). For example, a value of 5 indicates a BER thres…	Unsigned32r/w Constraints: range: 0-9	.1.3.6.1.4.1.164.6.2.15.5.1.1.28
prtParamLoopDetectStatus This object shows whether a loop was detected on the current port.	Enumeration Enumerated Values: 1 notApplicable 2 noLoop 3 loopDetected	.1.3.6.1.4.1.164.6.2.15.5.1.1.29
prtParamSupportedFeatures This MIB object denotes supported features by the port/interface. The bit legend must be kept identical to all devices. Bit 0 = '1' denotes that the port/interface supports ETH OAM CFM. The agent can set this bit to 1 o…	OctetString	.1.3.6.1.4.1.164.6.2.15.5.1.1.30
prtParamPortStatus This object shows the status of the current port. The status is a bit map represented as a sum, therefore, it can represent multiple failures. When no failure, the value will be 0. This object should be supported in add…	Bits Enumerated Values: 0 ais 1 rdi 2 loopDetected 3 faultPropagation 4 operStatus 5 adminStatus 6 notPresent 7 lowerLayerDown 8 macAccessSecViolation 9 signalDegradation 10 unknown 11 oamCriticalBitOn 12 los 13 autoNegotiationFailure 14 sfpFailure 15 lof 16 serialRateGeneratorFailure 17 serialRs232RateNot64kbps 18 voiceComboFailure 19 belowMinimumMembers 20 allLinksDown 21 linkFailSignaling	.1.3.6.1.4.1.164.6.2.15.5.1.1.31
prtParamSsmTx This object defines the SSM transmission from this port. For SDH/SONET interfaces the object means the following: disable (2): - force DNU (DUS) SSM message sending via TDM port - MAY stop SSM messages to PSN po…	Enumerationr/w Enumerated Values: 2 disable 3 enable	.1.3.6.1.4.1.164.6.2.15.5.1.1.34
prtParamAlias This object is an 'alias' name for the interface as specified by a network manager, and provides a non-volatile 'handle' for the interface.	OctetStringr/w Constraints: range: 0-255	.1.3.6.1.4.1.164.6.2.15.5.1.1.36
prtParamTxClockInstance This parameter specifies the instance of the clock domain that is used as transmision clock source. It is equal to the csmDomainEntry.csmDomainIdx when the CSM is used.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.15.5.1.1.38
prtParamEntPhysicalIndex The object contains index of the related entPhysicalEntry of the ENTITY-MIB (RFC 4133) and ENTITY-STATE-MIB (RFC 4268). The index is built accordign to the rules that are defined by the inventory.doc document.	ENTITY-MIBPhysicalIndexOrZero Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.164.6.2.15.5.1.1.41
prtParamSsmTxType This object defines the SSM transmission type from this port..	Enumerationr/w Enumerated Values: 1 type1Prc 2 type1SsuA 3 type1SsuB 4 type1Sec 5 type1Dnu 6 type1SsmBased 21 type2Prs 22 type2Stu 23 type2St2 24 type2Tnc 25 type2St3e 26 type2St3 27 type2Smc 28 type2St4 29 type2Dus 30 type2SsmBased 31 type2Prov 41 type3Unk 42 type3Sec 43 type3Dnu 44 type3SsmBased	.1.3.6.1.4.1.164.6.2.15.5.1.1.45

This table includes general port parameters, indexed by ifIndex

prtXEntry row .1.3.6.1.4.1.164.6.2.15.5.2.1

An entry in table.

Indexes

IF-MIBifIndex

Column	Syntax	OID
prtXCliPortString The exact string that is used by the CLI to identify this interface. The string includes the port type and the port identifier. Example port strings: 'ethernet main-a/1' 'ethernet 1' 'logical-mac 2'	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.164.6.2.15.5.2.1.1

A table - Parameters for IP Ports.

prtIpParamEntry row .1.3.6.1.4.1.164.6.2.15.6.1.1

An entry in table.

Indexes

prtIpParamConfigIdx prtIpParamSlotIdx prtIpParamIdx

Column	Syntax	OID
prtIpParamConfigIdx This object indicates the Configuration number (1..255) referred. Value of 255 specifies the TmpCnfg (Scratch). For products having Agent and Edit configurations, Write operation for the table entries is allowed only …	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.6.1.1.1
prtIpParamSlotIdx This object indicates a unique number of the slot position in which the module is inserted. notApplicable = 255 (for products that don't have slots). For KM: kmxMlA (103), kmxMlB (104).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.6.1.1.2
prtIpParamIdx This object indicates a unique Port Index.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.6.1.1.3
prtIpParamHostIP The host interface IP address.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.164.6.2.15.6.1.1.4
prtIpParamHostMask The host interface subnet mask.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.164.6.2.15.6.1.1.5
prtIpParamDefaultGateway Default Gateway's IP Address.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.164.6.2.15.6.1.1.6
prtIpParamMediaMode This object indicates the real Media Mode.	Enumeration Enumerated Values: 1 notApplicable 2 halfDuplex 3 fullDuplex	.1.3.6.1.4.1.164.6.2.15.6.1.1.7
prtIpParamMediaRate This object indicates the real Media Rate (Mbps).	Enumeration Enumerated Values: 1 notApplicable 2 r10Mbps 3 r100Mbps	.1.3.6.1.4.1.164.6.2.15.6.1.1.8
prtIpParamMngVlanSupport Management VLAN support (Tagging). no - No support of VLAN Tagging. yes - 4 VLAN bytes will be added to the frame.	Enumerationr/w Enumerated Values: 1 notApplicable 2 no 3 yes	.1.3.6.1.4.1.164.6.2.15.6.1.1.9
prtIpParamMngVlanId Management VLAN ID.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.6.1.1.10
prtIpParamMngVlanPriority Management VLAN Frame priority.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.6.1.1.11
prtIpParamRingMode This object indicates If Ring Mode is enabled or not.	Enumerationr/w Enumerated Values: 1 notApplicable 2 disable 3 enable	.1.3.6.1.4.1.164.6.2.15.6.1.1.12
prtIpParamProtIpEnable This object indicates whether a list of Protected IP Addresses is enabled or not. This object is applicable only if prtIpParamRingMode=enable.	Enumerationr/w Enumerated Values: 1 notApplicable 2 disable 3 enable	.1.3.6.1.4.1.164.6.2.15.6.1.1.13
prtIpParamTrafficPriority This object indicates the traffic priority of this port.	Enumerationr/w Enumerated Values: 1 notApplicable 2 low 3 high	.1.3.6.1.4.1.164.6.2.15.6.1.1.14
prtIpParamRemoteIP This is the IP Address of the remote device that is connected to the current device (Point to Point Application). It is used for sending OAM packets on the LAN to the remote side in order to check that the connection is…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.164.6.2.15.6.1.1.15
prtIpParamMaxTxBandwidth This object shows the Max Bandwidth allowed on the LAN. Full - means that a Maximum of 100 Mega Byte Rate may go through the LAN. e1(3) means that the maximum is an E1 rate. t1(4) is for a maximum of a T1 rate.	Enumerationr/w Enumerated Values: 2 full 3 e1 4 t1	.1.3.6.1.4.1.164.6.2.15.6.1.1.16
prtIpParamTos TOS = Type of Service transmitted. Valid values: 0..255.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.6.1.1.17
prtIpParamConnect Port Connection.	Enumerationr/w Enumerated Values: 1 notApplicable 2 no 3 yes	.1.3.6.1.4.1.164.6.2.15.6.1.1.18
prtIpParamAgingTime Aging Time in seconds.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.6.1.1.19
prtIpParamEncapsulationProt Encapsulation Protocol.	Enumerationr/w Enumerated Values: 1 notApplicable 2 tcp 3 udp	.1.3.6.1.4.1.164.6.2.15.6.1.1.20
prtIpParamEncapProtPort Encapsulation Protocol Port (TCP/UDP Port).	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.6.1.1.21
prtIpParamVlanSupport VLAN support (Tagging). 'no' - No support of VLAN Tagging. 'yes' - 4 VLAN bytes will be added to the frame.	Enumerationr/w Enumerated Values: 1 notApplicable 2 no 3 yes	.1.3.6.1.4.1.164.6.2.15.6.1.1.22
prtIpParamVlanId VLAN Identifier.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.6.1.1.23
prtIpParamVlanPriority VLAN Frame priority.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.6.1.1.24
prtIpParamDoubleTagVlanId VLAN Identifier of the Double Tagging VLAN.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.6.1.1.25
prtIpParamDoubleTagVlanPriority VLAN Frame priority of the Double Tagging VLAN.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.6.1.1.26
prtIpParamVlanTagging VLAN Tagging. 'unmodified' - No change will be done to the Frame. 'tag' - Add Tag to Untagged Frames. 'doubleTag' - Add Tag to all Frames. 'doubleTagAndFallBack' - Double Tagging will have different rules for VLANs th…	Enumerationr/w Enumerated Values: 1 notApplicable 2 unmodified 3 tag 4 doubleTag 5 doubleTagAndFallBack 6 untag	.1.3.6.1.4.1.164.6.2.15.6.1.1.27
prtIpParamRateLimit The maximum rate permitted to transfer via this port, in Kbps.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.6.1.1.28
prtIpParamDefInterface The Default Interface for packets with unresolved destination subnet. For internal-X port: 100 + X .	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.6.1.1.29
prtIpParamMng This object indicates whether Management is enabled/disabled via this port.	Enumerationr/w Enumerated Values: 1 notApplicable 2 disable 3 enable	.1.3.6.1.4.1.164.6.2.15.6.1.1.30
prtIpParamFloodedRateLimit The maximum rate permitted to transfer broadcast, multicast, and unicast flooded frames via this port, in Kbps. 0 - Disable. In Ipmux14 this parameter is applicable when prtIpParamRateLimit=0 (disable).	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.6.1.1.31
prtIpParamBurstSize The burst size that the port can support beyond rate limitation determined in prtIpParamRateLimit. Burst Size is measured in bytes.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.15.6.1.1.32
prtIpParamLimitPacketType The packet type that will be rate limited. Rate limitation determined in prtIpParamRateLimit. all - All packet types are rate limited. broadMultiFloodedUnicast - Broadcast, Multicast and Flooded Unicast packets are r…	Enumerationr/w Enumerated Values: 1 all 2 broadMultiFloodedUnicast 3 broadcastMulticast 4 broadcast	.1.3.6.1.4.1.164.6.2.15.6.1.1.33
prtIpParamKeepAliveInterval This parameter indicates the period of time (in msec.) between two consequent Keep Alive messages.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.6.1.1.34
prtIpParamKeepAliveThresh This parameter indicates the maximum number of missed Keep Alive answer messages acceptable, after which link status will be failed.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.6.1.1.35
prtIpParamP2pKeepAliveVlanId Dedicated VLAN ID for keep alive messages.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.6.1.1.36
prtIpParamP2pKeepAliveVlanPrio VLAN priority for P2P keep alive messages .	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.6.1.1.37
prtIpParamRingAdjacentMacAddr The MAC address of the adjacent NE connected to this port in an ETH ring. If the port is not a member of a ring, the value of this parameter will be 00-00-00-00-00-00.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.164.6.2.15.6.1.1.38

A table - Parameters for  master and fallback 
clock source of ports .

prtClkSrcEntry row .1.3.6.1.4.1.164.6.2.15.7.1.1

An entry in table.

Indexes

prtClkSrcCnfgIdx prtClkSrcPrtIdx prtClkSrcIdx

Column	Syntax	OID
prtClkSrcCnfgIdx This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.164.6.2.15.7.1.1.1
prtClkSrcPrtIdx This object indicates a unique Port Index (receiving clock). Refer to device specification for port Index	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.7.1.1.2
prtClkSrcIdx An index in the table. master - refers Master clock parameters fallback - refers Fallback clock parameters	Enumeration Enumerated Values: 1 master 2 fallback	.1.3.6.1.4.1.164.6.2.15.7.1.1.3
prtClkSrcMode This entry indicates the source the nodal timing is locked to.	Enumerationr/w Enumerated Values: 2 internal 3 rxClk 255 notApplicable	.1.3.6.1.4.1.164.6.2.15.7.1.1.4
prtClkSrcPrt This entry is valid only when working in rxClk mode. It specifies the port from which the clock willl be taken. Refer to device specification for source port Index	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.7.1.1.5

A table -  optical port (e.g SFP) monitoring parameters,
according to SFF-8472 Specification for Diagnostic Monitoring
Interface for Optical Xcvrs. and ITU-T rec. G.958

optPrtMonitorEntry row .1.3.6.1.4.1.164.6.2.15.8.1.1

An entry in table.

Indexes

optPrtMonitorPrtIdx optPrtMonitorSample

Column	Syntax	OID
optPrtMonitorPrtIdx This object indicates a unique (optical) Port Index . Refer to device specification for port Index.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.8.1.1.1
optPrtMonitorSample This index indicates historic and current values - minimum, maximum and actual (current) value.	Enumeration Enumerated Values: 1 actual 2 minimum 3 maximum	.1.3.6.1.4.1.164.6.2.15.8.1.1.2
optPrtMonitorTxPower Transmitted optical power level. Value is given in units of hundredth (1/100) of dBm.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.8.1.1.3
optPrtMonitorLaserBias LASER bias current level. Value is given in units of microAmper (uA).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.8.1.1.4
optPrtMonitorLaserTemp LASER temperature level, in hundredth (1/100) (C) degrees.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.8.1.1.5
optPrtMonitorRxPower Received optical power in units of hundredth (1/100) of dBm.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.8.1.1.6
optPrtMonitorSupplyVoltage Supply voltage, in hundredth (1/100) of volts (V).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.15.8.1.1.7

A table -  optical port configuration

optPrtCnfgEntry row .1.3.6.1.4.1.164.6.2.15.8.2.1

An entry in table.

Indexes

optPrtCnfgIdx optPrtCnfgPrtIdx

Column	Syntax	OID
optPrtCnfgIdx This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg.x.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.15.8.2.1.1
optPrtCnfgPrtIdx This object indicates a unique (optical) Port Index . Refer to device specification for port Index.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.6.2.15.8.2.1.2
optPrtCnfgALS enable/disable Automatic Laser Shutdown	Enumerationr/w Enumerated Values: 1 notApplicable 2 disable 3 enable	.1.3.6.1.4.1.164.6.2.15.8.2.1.3

This table describes the PS types of a device.
Usage of this table is specified in the device's NMS SRS

systemPsEntry row .1.3.6.1.4.1.164.6.2.25.1

An entry in table.

Indexes

systemPsIndex1 systemPsIndex2

Column	Syntax	OID
systemPsIndex1 First Index. In HUBs: 1 = PS-A slot 2 = PS-B slot 3 = PS-C slot. In SA units: 1 = PS1 2 = PS2 Default = 1	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.25.1.1
systemPsIndex2 Second Index. In HUBs: 1 always. In SA units: 1 = Local 2 = Remote Default = 1.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.25.1.2
systemPsType The type of PS, for a stand-alone product. acDc - PS that supports both AC and DC. acPF - Power Feeding (phantom) box that is feeding another box by external AC. dcPF - Power Feeding (phantom) box that is feeding anothe…	Enumeration Enumerated Values: 1 none 2 ac 3 dc 4 acDc 5 acPF 6 dcPF 7 acWithFan 8 dcWithFan 9 acHp	.1.3.6.1.4.1.164.6.2.25.1.3
systemPsStatus The Status of the PS unit.	Enumeration Enumerated Values: 1 notApplicable 2 failed 3 ok 4 degraded	.1.3.6.1.4.1.164.6.2.25.1.4
systemPsHotSwap Is PS unit hot swap or fixed.	Enumeration Enumerated Values: 1 notApplicable 2 fixed 3 hotSwap	.1.3.6.1.4.1.164.6.2.25.1.5

Configuration of system cross-connect entries.
The table follows the behavior described in RFC 2515, 
RFC 1604 regarding the creation deletion and modification 
of an entry within the table.

xcEntry row .1.3.6.1.4.1.164.6.2.31.1

An entry in table.

Indexes

xcIndex xcIfIndex1 xcVpi xcVci xcIfIndex2

Column	Syntax	OID
xcIndex Cross Connect Identifier.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.31.1.1
xcIfIndex1 The interface Index from the ifTable, which identify one side of the connection.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.31.1.2
xcVpi The VPI value.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.31.1.3
xcVci The VCI value.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.31.1.4
xcIfIndex2 The interface Index from the ifTable, which identifies the other side of the connection.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.31.1.5
xcRowStatus This parameter allows NMS to create/delete entries of this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.164.6.2.31.1.6
xcDescr A textual string containing information about the xc entry.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.164.6.2.31.1.7
xcAdminStatus The desired administrative status of this bi-directional cross-connect.	Enumerationr/w Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.164.6.2.31.1.8
xcOperStatus The operational status of this bi-directional cross-connect.	Enumeration Enumerated Values: 1 up 2 down 3 unknown	.1.3.6.1.4.1.164.6.2.31.1.9
xcAttachedIfType This object indicates if the specific VCC is already attached to any interface, and indicates the type of the interface. This object's purpose is to ease the checking to the NMS. notApplicable - used for entries that a…	Enumeration Enumerated Values: 1 notApplicable 2 free 3 routerAtm 4 lis	.1.3.6.1.4.1.164.6.2.31.1.10
xcInputPriority This object is the priority, by which the LAN frames will be internaly sent to the ATM HW. This parameter is applicable if atmNteMdlInputPriorityMechanism=enabled. 1 - Highest priority. Will be the fir…	Integer32r/w Constraints: range: 1-4	.1.3.6.1.4.1.164.6.2.31.1.11
xcBitMapping This object maps this entry to a bit of an octet string. For ACE2002 this object maps the LAN VCC to the bit of the VLAN Port Lists. If the value is '0' then it means that this VCC is not mapped to a port list or it m…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.31.1.12

This table include parameters for system modules.

modlParamEntry row .1.3.6.1.4.1.164.6.2.32.1.1.1

An entry in table.

Indexes

modlParamIndex

Column	Syntax	OID
modlParamIndex The module index. The index can be the slot number or any other module index as described in the specifications of the device. For Vmux-2100 device, the index will have values of: 1..4 for slots 1..4.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.6.2.32.1.1.1.1
modlParamReset Reset action to be performed on the module. Set the parameter will be done always to on(3) or factory (4). After performing the Reset operation, Agent will automatically set the parameter to off(2).	Enumerationr/w Enumerated Values: 2 off 3 on 4 factory	.1.3.6.1.4.1.164.6.2.32.1.1.1.2
modlParamSwdlStatus This parameter indicates whatever the swdl is in process or not.	Enumeration Enumerated Values: 1 notApplicable 2 off 3 inProcess	.1.3.6.1.4.1.164.6.2.32.1.1.1.3
modlParamLeds This entry specifies the LEDs status of the module. Each led is represented by 4 bits where the first 2 bits (left) specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) specify the color…	OctetString	.1.3.6.1.4.1.164.6.2.32.1.1.1.4
modlParamType This attribute indicates the Module Type.	Enumeration Enumerated Values: 2 unknown 3 empty 4 miRicE1 5 miRicT1 6 miRicE3 7 miRicT3	.1.3.6.1.4.1.164.6.2.32.1.1.1.5
modlParamSwVer This attribute indicates the Module's Software Version.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.164.6.2.32.1.1.1.6