prtTestTimeout
RAD-GEN-MIB ·
.1.3.6.1.4.1.164.6.2.15.4.1.1.5
Object
column
r/w
Integer32
This object is applicable only when a single test is running. It indicates the test activation timeout in minutes. For RICi-E1T1, RICi-E3T3 and LRS-16, the measurement unit is in seconds. When the timeout expires, the test is stopped. Value of 0 indicates test may run Forever
Context
- MIB
- RAD-GEN-MIB
- OID
.1.3.6.1.4.1.164.6.2.15.4.1.1.5- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- prtTestEntry
- Table
- prtTestTable
- Siblings
- 26
Syntax
Integer32
Values & Constraints
Object Constraints
range: 0-86400
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| prtTestIdx This object is an index of the specific port or interface.
For a port, the index will be as agreed between agent and
application.
For an interface, ifIndex may be used. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.6.2.15.4.1.1.1 |
| prtTestVctCmd Vct command.
on (3) = Start Vct on both cables connected to
RX and TX connectors of this port.
Agent will perform the required command and change automatically
the value of this… | column | Enumeration | .1.3.6.1.4.1.164.6.2.15.4.1.1.10 |
| prtTestVctRxCrossPair This object should be equal to the Index (prtTestIdx) of the Rx cross pair.
This object is applicable only for Vct Result = shortToCrossPair or coupleWithCrossPair.
This object w… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.6.2.15.4.1.1.11 |
| prtTestVctTxCrossPair This object should be equal to the Index (prtTestIdx) of the Tx cross pair.
This object is applicable only for Vct Result = shortToCrossPair or coupleWithCrossPair. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.6.2.15.4.1.1.12 |
| prtTestActivationDelay This object is applicable only when a single test is running.
It indicates test activation delay in seconds.
A Value of 0 indicates that the test starts immediately. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.164.6.2.15.4.1.1.13 |
| prtTestMacSwapLoopDataMode This object defines which part
of the data will be looped back. | column | Enumeration | .1.3.6.1.4.1.164.6.2.15.4.1.1.14 |
| prtTestMacSwapLoopVlanId This object specifies the VLAN ID for
prtTestMacSwapLoopDataMode=specificVlan. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.6.2.15.4.1.1.15 |
| prtTestMacSwapLoopDirection This object defines the direction of the performed loopback.
In ETX102 'local' corresponds to Ingress loop
(either on User port or on Network port), and
'remote' corresponds to Eg… | column | Enumeration | .1.3.6.1.4.1.164.6.2.15.4.1.1.16 |
| prtTestMacSwapLoopDestAddr Configures the MAC address that will be sent in the
Destination field of the packet in the outgoing direction. | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.164.6.2.15.4.1.1.17 |
| prtTestMacSwapLoopSrcAddr Configures the MAC address that will be sent in the
Source field of the packet in the outgoing direction. | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.164.6.2.15.4.1.1.18 |
| prtTestOamMinRoundTripDelay The mininal value of round trip delay of loopback message for a session of
OAM loopback.Units are msec. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.164.6.2.15.4.1.1.19 |
| prtTestCmdAndStatus Setting this object to a value as detailed further on
(except 0) will initiate a test on the specific port.
The test/s requested will be set according to the respective
bit. The v… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.6.2.15.4.1.1.2 |
| prtTestOamMaxRoundTripDelay The maximum value of round trip delay of loopback message for a session of
OAM loopback.Units are msec. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.164.6.2.15.4.1.1.20 |
| prtTestOamAvgRoundTripDelay The average round trip delay of loopback message for a session of
OAM loopback.Units are msec. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.164.6.2.15.4.1.1.21 |
| prtTestOamTxInterval Indicates the interval between loopback sent messages.Units are msec. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.164.6.2.15.4.1.1.22 |
| prtTestDestinationIpAddress Indicates the destination IP Address in the transmitted messages that
are looped back. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.164.6.2.15.4.1.1.23 |
| prtTestForceTTL Time-to-live.Number of hops the loopback message will go through the net
before deciding to discard it. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.164.6.2.15.4.1.1.24 |
| prtTestBwProfile deprecated Indicates the BW profile (from bwProfileTable) that is assigned to the loopback test
in order to limit the traffic that is looped back. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.164.6.2.15.4.1.1.25 |
| prtTestSourceIpAddress Indicates the source IP Address in the transmitted messages that
are looped back. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.164.6.2.15.4.1.1.26 |
| prtTestRemainTime Indicates the remain time for test activation
in seconds. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.164.6.2.15.4.1.1.27 |
| prtBertCounter This object indicates the number of BERT errors encountered
during the BERT operation.
It is valid only when BERT (Bit Error Rate Test) is active on the
specific port.
The Counte… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.6.2.15.4.1.1.3 |
| prtTestInitiator This object indicates who initiated this port's test/s. | column | Enumeration | .1.3.6.1.4.1.164.6.2.15.4.1.1.4 |
| prtTestVctRxResult This object indicates the result of the Vct on
the cable connected to the RX connector. | column | Enumeration | .1.3.6.1.4.1.164.6.2.15.4.1.1.6 |
| prtTestVctTxResult This object indicates the result of the Vct on
the cable connected to the TX connector. | column | Enumeration | .1.3.6.1.4.1.164.6.2.15.4.1.1.7 |
| prtTestVctRxDistance This object indicates the distance in Meters
to the RX cable Open/ Short location discovered by the Vct.
This parameter is applicable for Vct Result = Normal or Fail only,
Else … | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.6.2.15.4.1.1.8 |
| prtTestVctTxDistance This object indicates the distance in Meters
to the TX cable Open/ Short location discovered by the Vct.
This parameter is applicable for Vct Result = Normal or Fail only,
Else … | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.6.2.15.4.1.1.9 |