prtTestCmdAndStatus

Setting this object to a value as detailed further on
(except 0) will initiate a test on the specific port.
The test/s requested will be set according to the respective
bit. The value of this object will be a sum of (2**n), where n is
the Bit:
  TEST                          BIT                       VALUE
 -----------                    ---                      ------
 reserved                        0                            1
 PayloadLoop=RLB                 1 (=Remote Loopback)         2
 LineLoop=DIG                    2 (=Digital)                 4
 OtherLoop                       3                            8
 InwardLoop=LLB                  4 (=Local Loopback)         16
 BERT                            5                           32
 LC                              6                           64
 ToneInjection                   7                          128
 Inband                          8                          256
 BERT Remote (or E1/T1 RLB)      9                          512
 Downstream-AIS (or E1/T1 LLB)  10                         1024
 Upstream-AIS                   11                         2048
 Rem-Loop-on-Rem-Unit           12                         4096
 MacSwapLoop                    13                         8192
 OamETHLoopback                 14                        16384
 OamETHLinkTrace                15                        32768
 IPSwapLoop                     16                        65536
 TrafficRoute                   17                       131072
 lbmResponder                   18                       262144
 macDestLoop                    19                       524288
 macSourceLoop                  20                      1048576
 udpLoop                        21                      2097152
 udpEcho                        22                      4194304
 twamp                          23                      8388608
 discardTraffic                 24                     16777216  
              
 e.g : If the requested value is 20 -> 010100  ->
       Bits 2 & 4 are set -> the requested tests are :
                             LineLoopback=DIG
                             InwardLoopback=LLB
              
Not all tests combinations are valid.
For valid test combination, see each product's specification.
For LRS52, only single test is allowed simultaneously
              
The terminology and order of the first tests (except BERT)
is according to the one used for Test Status of DS1 and DS3 standards.
The notations : RLB, LLB, DIG are the most used in RAD's products, but they
can be different. For exact definition see product's spec.
              
Setting this object to stop (value=0 ; all bits are 0),
will stop all the user requested tests running on the
selected port.
              
When no test is running on the port, the Get value (test status)
will be 0.
              
PayloadLoop=RLB
  The received signal at this interface is looped
  through the device.  Typically the received signal
  is looped back for retransmission after it has
  passed through the device's framing function.
              
LineLoop=DIG
  The received signal at this interface does not
  go through the device (minimum penetration) but
  is looped back out.
              
OtherLoop
  Loopbacks that are not defined here.
              
InwardLoop=LLB
  The sent signal at this interface is looped back
  through the device.
              
LC
This loop is applicable only for HSSI interface, towards the router .
              
ToneInjection
This loop is applicable for analog voice (like FXS).
              
Downstream-AIS
E1 AIS signal (all ones) is transmitted in the relevant channel
toward the STM-1 line.
              
Upstream-AIS
E1 AIS signal (all ones) is generated in the relevant channel
toward the local received tributary channel output
              
Rem-Loop-on-Rem-Unit
Request from far end device to activate remote loopback
towards near-end device
              
MacSwapLoop
  This loop is applicable for ethernet port. Loop is
  implemented by swapping the MAC addresses of the
  incoming message.
              
OamETHLoopback
   Ethernet Loopback is used to verify connectivity of a MEP with a MIP
   or peer MEP(s) (ITU-T Y.1731, Clause 7.2).
              
OamETHLinkTrace
   Ethernet Link Trace is an on-demand OAM function which can be used for
   the two following purposes:
   - Adjacent Relation Retrieval
   - Fault Localization
   (ITU-T Y.1731, Clause 7.3).
              
IPSwapLoop
  This loop is applicable for ethernet port. Loop is
  implemented by swapping the IP addresses of the
  incoming message.In ETX-202A, this test causes also swapping of
  the the MAC address (bit 13 should also be set to 1).
              
TrafficRoute
  Traffic Route is an on-demand flow function which can be used for
  flow activation for predefined time duration .
              
lbmResponder
Activate rfc2544 Loopback (lbm) responder (on flow level).
              
macDestLoop
This loop is applicable for Ethernet port. A packet with destination
MAC address equal to macDestLoop will be looped.
              
macSourceLoop
This loop is applicable for Ethernet port. A packet with destination
MAC address equal to macSourceLoop will be looped.
              
udpLoop
This loop is applicable for Ethernet port. UDP loop is
implemented by swapping destination and source MAC addresses,
IP addresses and UDP ports of the incoming message.
              
udpEcho
A debugging and measurement tool. An echo service simply sends back
to the originating source any data it receives. A server listens for
UDP datagrams on configurable UDP port. When a datagram is received,
the data from it is sent back in an answering datagram.
              
twamp
This loop provides the functionality of TWAMP responder.
                     
discardTraffic
Drop incoming traffic on the specified flow or port.

MIB

RAD-GEN-MIB

OID

.1.3.6.1.4.1.164.6.2.15.4.1.1.2

Type

column

Access

readwrite

Status

current

Parent

prtTestEntry