agnFunctionAttributes

This MIB object indicates for each supported function
its set of attributes.
              
For ETH OAM-CFM: (agnFunction enumeration 8)
Bit 0 = '1' denotes that the device supports C+S classification.
Bit 1 = '1' denotes that the device supports port level binding.
Bit 2 = '0' denotes that the device supports queueing for OAM frames.
Bits 3-7 - reserved  (for future usage of Phase 1 features)
              
The following are supported starting from OAM-CFM Phase 2 and up:
Bit 8  = '1' Dest NE level is supported
Bit 9  = '1' Port level MEP is supported
Bit 10 = '1' Dynamic Remote MEP allocation
Bit 11 = '1' Dynamic Service allocation
Bit 12 = '1' Use identical VLAN ID in different MD levels
Bit 13 = '1' Single-ended loss measurement
Bit 14 = '1' Two-way delay measurement
Bit 15 = '1' 10msec CCM interval is supported
Bit 16 = '1' Use identical VLAN ID in multiple MEPs, which are members
             of the same MA (different priority) -- NON STANDARD
              
The following are supported starting from OAM-CFM phase 3 and up:
              
Bit 17. Entu -
    ENTU includes Hardware Based Features:
    CCM Interval value: 3.3 msec, and
    Forwarding-Method (E-LAN, E-Line)
    (There is no specific bit for these items)
              
Bit 18. Direction (up, down)
Bit 19. Lmm-Dmm interval
Bit 20. LBM data-tlv
Bit 21. DMM data-tlv
Bit 22. Loss traffic-type
Bit 23. Measurement Bins. (Round Trip Delay counters only)
Bit 24. ETH-AIS - Fault Propagation
Bit 25. ETH-AIS - Alarm Suppression
Bit 26. MIP none and explicit
Bit 27. MIP Defer, Default
Bit 28. Cross Connect Status
Bit 29. Variable Duration statistics interval (pmIntervalTimeDuration is supported)
              
Bit 30  MIP Tx Flow
Bit 31  MIP Rx Flow
              
Bit 32  MIP and MHF manual configuration
Bit 33  MHF Single VLAN
Bit 34  MHF Fixed CoS
Bit 35  MHF Fixed Queue
Bit 36  MHF Classification Profile
Bit 37  MHF CoS Profile
Bit 38  MHF Queue Profile
Bit 39  MD Protocol Standard selection
              
Bit 40  MEP Single VLAN
Bit 41  MEP Fixed CoS
Bit 42  MEP Fixed Queue
Bit 43  MEP Classification Profile
Bit 44  MEP CoS Profile
Bit 45  MEP Queue Profile
Bit 46  MEP Tx Flow
Bit 47  MEP Rx Flow
              
Bit 48    The device supports both MIP configuration modes (manual and auto)
           If this Bit is set to 0 -> The device supports only one configuration
           mode (see Bit 32 that indicates the configuration mode)
           If this Bit is set to 1 -> The device supports both configuration modes
           (bit 32 will indicates which mode has been selected)
              
Bit 49     Agent Supports all objects indicating min/max Delay and min/max Delay Variations.
              
Bit 50 MD Name & MD Format ('1' = not supported)
Bit 51 MD MIP Policy ('1' = not supported)
Bit 52 MA Name & MA Format ('1' = not supported)
Bit 53 LBM,LTM and Dest NE - Remote MEP ID ('1' = not supported)
              
Bit 54 ethOamSvcDayTable is supported instead of ethOamSvcTotalTable
Bit 55 = '1' 100 msec CCM interval is supported . (for ETX-36)
Bit 56 = '1' MEP is supported only for network port. (for ETX-36)
              
Bit 57  = '1', All one way (Forward) Perfromance Measurements
(Delay, Delay Variation) are supported.
              
Bit 58 = '1' Multiple flows (unidirectional Rx and Tx, bidirectional) per MEP are supported.
         (ethOamMepFlowsTable is supported)
              
              
Bit 59 = '1' -  For MD Name Format, ONLY 'None' and 'String' are supported.
              (MD Name is supported)
Bit 60 = '1' -  For MA Name Format, ONLY 'UINT' (UnsignedInt16) and 'String' are supported.
              (MA Name is supported)
Bit 61 = '1' - SLM supported
Bit 62 = '1' - Availability per MEF36 supported (configuration and statistics)
Bit 63 = '1' - CFM Alarm type configuration is supported (legacy or soam)
Bit 64 = '1' - Configurable Interface Status TLV usage
Bit 65 = '1' - Configurable Dest-Ne description
Bit 66 = '1' - One Way delay variation supported ( forward/backward, bin profiles, statistics)
Bit 67 = '1' - LBM multicast address supported
Bit 68 = '1' - CCM statistics per MEP supported (Local/Remote, running, current and history intervals)
Bit 69 = '1' - For MA Name Format, ONLY 'UINT' (UnsignedInt16), 'String' and 'ICC' are supported.
               (MA Name is supported)
Bit 70 = '1' - ETH-CSF indications for Remote MEP is supported.
Bit 71 = '1' - Latching Loopback per MEF46 is supported.
              
For File Transfer:   (agnFunction enumeration 9) (refer also to fileTransCmd)
In each bit field, the value '1' denotes that the device supports the operation/behavior.
Bit 0  - Configuration file is in text format -- moved to agnFunction=cli(12)
Bit 1  - SW Download
Bit 2  - Configuration Download
Bit 3  - Configuration Upload
Bit 4  - Additional SW Download
Bit 5  - Statistics Upload
Bit 6  - User File Download
Bit 7  - User File Upload
Bit 8  - SW Download and Reset
Bit 9  - SW Upload
Bit 10 - SW Download to Backup (therefore also Swap Main and Backup)
Bit 11 - Boot Download
Bit 12 - Boot Upload
Bit 13 - SW Upload from Backup
Bit 14 - License Download
Bit 15 - Configuration Download to Default
Bit 16 - Reset operation
Bit 17 - Configuration Download to Active Configuration
Bit 18 - Additional SW Download and Reset
Bit 19 - The policy for Software Download is as follows:
         After download the NMS should send Reset to the device.
Bit 20 - The policy for Software Download is as follows:
         After download the device performs a Reset by itself.
Bit 21 - The policy for Configuration Download is as follows:
         After download the NMS should send Reboot command to the device.
Bit 22 - The policy for Configuration Download is as follows:
         After download the device performs a Reset by itself.
Bit 23 - The policy for Software Download is as follows:
         Like in Bit 20, except that the command sent in fileTransCmd is swDwnLoadAndReset(8).
Bit 24 - The policy for Configuration Download is as follows:
         After Configuration download the device activates the configuration file and sends
         sanityCheckTrap with attached variable sysSSanityCheckStatus = ok(4) or warning(3).
Bit 25 - The policy for Configuration Download is as follows:
         Like in Bit 22, except that the trap sent is
         sanityTrap with attached variable agnSSanityCheckStatus = ok(4) or warning(3)
Bit 26 - Total Timeout (tftpTotalTimeOut) -- Not Applicable
Bit 27 - Retry Timeout (tftpRetryTimeOut) -- Not Applicable
Bit 28 - It is forbidden to send the device retries for Reset (after Download) operation.
Bit 29 - Upload Factory Default Configuration file        -- Not Applicable
Bit 30 - Download/Upload User Default Configuration file  -- Not Applicable
Bit 31 - Download/Upload Startup Configuration file       -- Not Applicable
Bit 32 - SFTP is supported.                               -- Not Applicable. Supported via agnCommonCapabilities
Bit 33 - The policy for Configuration Download is as follows:
         Like in Bit 24, except no sanity trap is sent.
              
    For CLI:  (agnFunction enumeration 12)
Bit 0  - Configuration file is in text format (replacing bit 0 of File Transfer)
              
    For CSM:  (agnFunction enumeration 13)
Bit 0 - '1' Domain is supported as 'clock source'
Bit 1 - '1' Station port exists in system
Bit 2 - '1' RX port is supported as 'clock source'
Bit 3 - '1' 'adaptive' is supported as 'clock source'
Bit 4 - '1' '1588' is supported as 'clock source'
Bit 5 - '1' Station-out port exists in system
Bit 6 - '1' GPS is supported as 'clock source'
Bit 7 - '1' E1/T1 is supported as 'clock source'    
              
    For ERP:  (agnFunction enumeration 14)
Bit 0 - '1': ERP supported (STD G.8032). '0': ERP not supported
Bit 1 - '0': Sub Ring supported.'1':Sub Ring not supported
Bit 2 - '1': Internal Flows supported. '0': Internal Flows not supported
Bit 3 - '1': multiple rings per physical port supported. '0': Multiple rings not supported
Bit 4 - '1': Passthrough VLANs supported. '0':Passthrough VLANs not supported 
Bit 5 - '1': color mapping also by P-bit. '0': Color mapping by P-bit not supported
Bit 6 - '1': Passthrough VLAN IDs supported. '0':Passthrough VLAN IDs not supported 
Bit 7 - '1': ERP STD G.8032v2 supported. '0': ERP STD G.8032v2 not supported
              
    For TDM PW   (agnFunction enumeration 21)
Bit 0 - '1' CESoPSN TDM traffic supported
Bit 1 - '1' SAToP TDM traffic supported
Bit 2 - '1' TDM PW Connectivity current and Interval statistics is supported
        (pwPerfConnCurrentTable, pwPerfConnIntervalTable)
              
              
For Smart SFP bit (agnFunction enumeration 23):
Bit 0  N/A
Bit 1  N/A
Bit 2  This device supports Smart SFP type: miRIC-E1
Bit 3  This device supports Smart SFP type: miRIC-T1
Bit 4  This device supports Smart SFP type: miRIC-E3
Bit 5  This device supports Smart SFP type: miRIC-T3
Bit 6  This device supports Smart SFP type: miRICi-E1
Bit 7  This device supports Smart SFP type: miRICi-T1
Bit 8  This device supports Smart SFP type: miRICi-E3
Bit 9  This device supports Smart SFP type: miRICi-T3
Bit 10 This device supports Smart SFP type: miRICi-155
Bit 11 This device supports Smart SFP type: miRICi-622
Bit 12  This device supports Smart SFP type: miTOP-E1
Bit 13  This device supports Smart SFP type: miTOP-E3
Bit 14  This device supports Smart SFP type: miTOP-T1
Bit 15  This device supports Smart SFP type: miTOP-T3
Bit 16  This device supports Smart SFP type: sfp-VDSL-2W
              
              
For PTP (agnFunction enumeration 24)
Bit 0 - '0' Slave is not supported. '1' Slave is supported.
Bit 1 - '0' Master is not supported. '1' Master is supported.
              
              
For Copy File ( agnFunction enumeration 25)
Bit 0 - Indicates if download and upload user file is supported.
Bit 1 - Indicates if download a running configuration file.
Bit 2 - Indicates if device performes reboot after install SW (set-active).
Bit 3 - Indicates if device supports Rollback SW.
Bit 4 - Indicates if device supports log files.
Bit 5 - Indicates if device supports download statistics.
Bit 6 - Indicates if device supports FileType value = otherType(2)
Bit 7 - '1' Indicates that the device does not support rowInfoTableId
              
              
For Router  (agnFunction enumeration 26)
Bit 0 - Indicates if device supports multiple instances.
Bit 1 - '0': HW Router exists in device. '1': SW Router exists in device.
Bit 2 - '0': DHCP Relay is not supported. '1': DHCP relay is supported.
Bit 3 - '0': IP Forwarding (RtrIfCfgIpForwarding) is not supported. 
        '1': IP Forwarding is supported
              
              
For Fault Management (agnFunction enumeration 28):
Bit 0  Indicates activeAlarmTable is supported
Bit 1  Indicates alarmEventBriefLogTable (Summary Table) is supported
Bit 2  Indicates alarmEventLogTable  (History Log) is supported
Bit 3  Indicates alarmEventConfigTable and maskReportTable  (Severity and Masking Configuration) is supported
Bit 4  Indicates alarmEventConfiguredTable is supported
Bit 5  Indicates Alarm Led is Supported
Bit 6  Indicates Alarm Output Relay is supported (alarmRelayOutputTable)
Bit 7  Indicates Alarm Input Relay is supported (alarmRelayInputTable)
Bit 8  Indicates Soaking configuration is supported (defectSoakTable)
Bit 9  Indicates Popup alarm indications are supported.
Bit 10 Indicates device has Slots
Bit 11 Indicates Input Relay exists on chassis
Bit 12 Indicates Input Relay(s) exist on slot(s)
Bit 13 Indicates Output Relay exists on chassis
Bit 14 Indicates Output Relay(s) exist on slot (s)
Bit 15 Indicates Alarm Masking Statistics is supported
         (AlarmEventLogStatsType = activeAlarmsMasked(4))
              
              
For Bridge (agnFunction enumeration 31):
Bit 0  Indicates support with Bridge Topology.
Bit 1  '0':Vlan Mode=Aware only.'1':Vlan Mode=Aware and Unaware.
Bit 2  '0': Forwarding Mode=Filter only.'1': Forwarding Mode=Filter and Transparent.
Bit 3  '0': Bridge Port can be Bound to SVI. '1': Bridge Port cannot be Bound to SVI.
Bit 4  '0': Bridge Port cannot be Bound to Phy Port. '1': Bridge Port can be Bound to Phy Port.
Bit 5  '0': MAC Table is not displayed in Bridge GUI. '1': MAC Table displayed in Bridge GUI.
Bit 6  '0': MAC Table displayed per Vlans. '1': MAC TAble not displayed per Vlan (unsorted).
Bit 7  '0': Table radBridgePortVlanMemberTable not supported. '1': Table radBridgePortVlanMemberTable supported.
Bit 8  '0': search MAC per MAC Criteria is not supported. '1': search MAC per MAC Criteria is supported.
Bit 9  '0': search MAC per Vlan Criteria is not supported. '1': search MAC per Vlan Criteria is supported.
Bit 10 '0': search MAC per Bridge Port Criteriais not supported. '1': search MAC per Bridge Port Criteria is supported.
Bit 11 '0': RSTP is not supported '1': RSTP is supported.
Bit 12 '0': MSTP is not supported '1': MSTP is supported.
Bit 13 '0': MLDv2 snooping is not supported '1': MLDv2 snooping is supported.
              
              
For acl ( agnFunction enumeration 32):
Bit 0   IPv4 ACL-type is supported,
Bit 1   IPv6 ACL-type is supported,
Bit 2   Management Entity bound to ACL is supported,
Bit 3   Router Interface bound to ACL is supported,
Bit 4   Inbound Direction bound to ACL is supported,
Bit 5   Outbound Direction bound to ACL is supported,
Bit 6   IP Protocol based ACL match is supported,
Bit 7   UDP Protocol based ACL match is supported,
Bit 8   TCP Protocol based ACL match is supported,
Bit 9   ICMP Protocol based ACL match is supported.
Bit 10  Port Range Support.
       '0' - only noOperator(1) is supported for xxxPortOp fields;
             xxxPortRange field value must be equal to xxxPort field.
       '1' - only 'range (6)' is supported for xxxPortOp field; xxxportRange field must be >= xxxPort.
              
              
For Performance Management (agnFunction enumeration 36):
Bit 0  '0':PM v3 Protocol not supported.'1':PM v3 Protocol supported.
Bit 1  '0':PM File Schema not supported.'1':PM V3 File Schema supported.
              
              
For Y.1564 testing (agnFunction enumeration 37):
Bit 0  - '1': generator supported.
Bit 1  - '1': responder supported.
Bit 2  - '1': unidirectional mode supported.
Bit 3  - '1': bidirectional mode supported.
Bit 4  - '1': color-aware supported.
Bit 5  - '1': traffic policy supported.
Bit 6  - '1': MAC swap functionality supported.
Bit 7  - '1': EMIX supported.
Bit 8  - '1': CBS/EBS tests supported.
Bit 9  - '1': Internal MEP supported.
Bit 10 - '1': E-LAN/E-Tree supported.
Bit 11 - '1': E-LAN/E-Tree supported for internal MEP.
Bit 12 - '1': configurable block or not block of user traffic. '0': user traffic is always blocked.
Bit 13 - '1': jumbo frames supported.
Bit 14 - '1': multiple SA MAC for LAG supported.
Bit 15 - '1': automatic creation of CFM services and destNEs supported.
              
              
For Policer (agnFunction enumeration 39)
Bit 0 - '0' Color Aware supported. '1' Color Aware not supported.
Bit 1 - '0' Coupling Flag supported. '1' Coupling Flag is not supported.
Bit 2 - '1' Envelope policer supported.
              
              
For LLDP (agnFunction enumeration 40)
Bit 0 - '1' denotes that the device supports LLDP.
              
              
For TWAMP (agnFunction enumeration 41)
Bit 0 - '1' denotes that the device supports TWAMP light Responder.
Bit 1 - '1' denotes that the device supports TWAMP light Generator.
Bit 2 - '1' denotes that the device supports TWAMP (full) Responder.
Bit 3 - '1' denotes that the device supports TWAMP (full) Generator.
Bit 4 - '1' denotes that the device supports icmpEcho Generator. 
Bit 5 - '1' denotes that the device supports udpEcho Generator. 
              
              
For Flow (agnFunction enumeration 42)
Bit 0 - '1' enhanced CoS mapping is supported (untagged, non-ip).
Bit 1 - '1' multi-CoS flow counters are supported.
Bit 2 - '0' denotes that the CIR & EIR shall always be set to the closest lower granular value - not configurable.
        '1' denotes that the CIR & EIR can be set to the closest lower or higher granular value - configurable.
Bit 3 - '1' denotes support for flow type 'port classifier'.
              
              
For vrrp (agnFunction enumeration 43)
Bit 0 - '1': VRRP version 2 is supported
Bit 1 - '1': VRRP version 3 is supported.
              
              
For L3 SAT  (agnFunction enumeration 44)
Bit 0 - '1': generator supported.
Bit 1 - '1': responder supported.
              
              
For Port & Flow Mirroring  (agnFunction enumeration 45)
Bit 0 - '1': VLAN list mirroring is supported.
Bit 1 - '1': flow mirroring is supported.
              
              
For Ethernet Port  (agnFunction enumeration 46)
Bit 0 - '1': Silent Start is supported.
Bit 1 - '1': Fat Pipe is supported.
Bit 2 - '1': Maximum two queue blocks are supported. 
              
              
For DHCP Layer 2 Relay  (agnFunction enumeration 47)
Bit 0 - '1': DHCP Layer 2 Relay Snooping is supported.
Bit 1 - '1': DHCP Layer 2 Relay option 82 is supported.
Bit 2 - '1': Circuit ID for option 82 is supported.
Bit 3 - '1': Remote ID for option 82 is supported.
              
              
For NAT  (agnFunction enumeration 48)
Bit 0 - '1': Static NAT is supported.
Bit 1 - '1': 'Hole Punching' is supported.
Bit 2 - '1': NAPT/PAT/Overload is supported.
Bit 3 - '1': Router Interface as inside global IP address is supported.
              
              
For Cellular  (agnFunction enumeration 49)
Bit 0 - '1': Cellular Interface is supported.

MIB

RAD-GEN-MIB

OID

.1.3.6.1.4.1.164.6.2.45.1.3

Type

column

Access

readonly

Status

current

Parent

agnFunctionEntry

Table

agnFunctionTable

Siblings

3