Cisco90Series-MIB Table View
Table-centric layout grouping table, row, and column objects.
Tables
9
Rows
9
Columns
114
.1.3.6.1.4.1.1570.1.3.1
·
1 row entry
·
2 columns
This Cisco 90 Series Bank Di-group Table contains channel bank level information for each of the channel bank di-groups in the system. A di-group is a T1 interface to the frame relay network. The table is indexed using the Cisco 90 Series channel bank digroup number
A specific entry in the Cisco 90 Series Bank Di-group
Table. There is one entry for each channel bank di-group
(T1) in the system. There are no entries for unused banks
Table. There is one entry for each channel bank di-group
(T1) in the system. There are no entries for unused banks
Indexes
frxBankIndex
| Column | Syntax | OID | ||
|---|---|---|---|---|
|
frxBankIndex
mandatory
Channel Bank Di-group Number. This index is used to address
the various channel banks in the system. This number is the same as the DLCI number used to communicate with the bank at the Cisco 90 SNMP Agent. (note that th… |
Integer32 Constraints: range: 16-1007 |
.1.3.6.1.4.1.1570.1.3.1.1.1 |
||
|
frxBankType
mandatory
This is the type of channel bank and is for future use.
D4 banks return a value of 1. |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.1570.1.3.1.1.2 |
.1.3.6.1.4.1.1570.1.4.1
·
1 row entry
·
16 columns
This Cisco 90 Series Channel Unit Table contains channel unit level control and statistics for each of the Cisco 90 Series channel units in the system. The table is indexed first using the Cisco 90 Series channel bank digroup number, then the channel unit number (1 to 24).
A specific entry in the Cisco 90 Series Channel Unit Table.
There is one entry for each Cisco 90 Series channel unit in
the system. There are no entries for unused banks or empty
channel unit slots
There is one entry for each Cisco 90 Series channel unit in
the system. There are no entries for unused banks or empty
channel unit slots
Indexes
frxBankIndex frxChUIndex
| Column | Syntax | OID | ||||
|---|---|---|---|---|---|---|
|
frxChUIndex
mandatory
Channel Unit Number. This index is used to address a
specific channel unit in a bank. For D4 channel banks this number is the same as the physical slot number 1-24 |
Integer32 Constraints: range: 1-24 |
.1.3.6.1.4.1.1570.1.4.1.1.1 |
||||
|
frxChUType
mandatory
Type of Cisco 90 Series channel unit installed.
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.1570.1.4.1.1.2 |
||||
|
frxChUVersion
mandatory
Cisco 90 Series channel unit version number.
|
Integer32 Constraints: range: 0-65535 |
.1.3.6.1.4.1.1570.1.4.1.1.3 |
||||
|
frxSigProtocol
mandatory
This is the type of Local In-channel Signaling used
when the subscriber is running frame relay protocol. It is provided for future use. Set to 1 for T1.617 Annex-D |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.1570.1.4.1.1.4 |
||||
|
frxConfigSrc
mandatory
Source for configuring speed and protocol for each port.
1=Data rate and protocol set by DLCI assignment rules as reported by Annex-D. This option allows control of these basic parameters from the frame relay switc… |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.1570.1.4.1.1.5 |
||||
|
frxDLCIAdLen
mandatory
The number of bytes used for the DLCI address.
For future use. 1=two octets. |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.1570.1.4.1.1.6 |
||||
|
frxNetInOctets
mandatory
Total number of octets received by this channel
unit from Frame Relay Switch (on the T1 interface) Only frames whose DLCI is addressed to a port on this channel unit are counted. Bad frames, Annex-D and SNMP frames are… |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.4.1.1.7 |
||||
|
frxNetOutOctets
mandatory
Total number of octets transmitted to the Frame
Relay Switch (on the T1 interface) by this channel unit. Annex-D and SNMP frames are not counted. CRC bytes are not counted |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.4.1.1.8 |
||||
|
frxNetBadFrames
mandatory
Total number of frames received on the network (T1)
interface that are discarded by this channel unit. Possible reasons for discard are: Frame contained HDLC abort (7 or more ones in a row) Frame had a CRC error … |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.4.1.1.9 |
||||
|
frxNetHDLCEs
mandatory
Network Errored Seconds caused by HDLC aborts (7 or more
ones in a row). Total number of seconds in which a frame with an HDLC abort is received by this channel unit on the network (T1) interface. Only frames whose DLCI… |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.4.1.1.10 |
||||
|
frxNetCRCEs
mandatory
Network Errored Seconds caused by CRC errors.
Total number of seconds in which a frame with a CRC error is received by this channel unit on the network (T1) interface. Only frames whose DLCI is addressed to a port on th… |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.4.1.1.11 |
||||
|
frxNetLinkEs
mandatory
Network Errored Seconds caused by Non-integral Bytes.
Total number of seconds in which a frame with a non-integral number of bytes is received by this channel unit on the network (T1) interface. Only frames whose DLCI i… |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.4.1.1.12 |
||||
|
frxNetFrShEs
mandatory
Network Errored Seconds caused by Short Frames received.
Total number of seconds in which a frame that is too short (less than 5 bytes) is received by this channel unit on the network (T1) interface. Only frames whose D… |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.4.1.1.13 |
||||
|
frxNetFrLgEs
mandatory
Network Errored Seconds caused by Long Frames received.
Total number of seconds in which a frame that is too long (more than 8192 bytes) is received by this channel unit on the network (T1) interface. Only frames whose … |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.4.1.1.14 |
||||
|
frxNetPPPEs
mandatory
Errored seconds caused by bad RFC-1973 (PPP) header.
Total number of seconds in which a frame with an invalid RFC-1973 (PPP) header is received by this channel unit on the network (T1) interface. Only frames whose DLCI … |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.4.1.1.15 |
||||
|
frxNetBufEs
mandatory
Errored Seconds caused by Buffer Overflow.
Total number of seconds in which a frame received by this channel unit on the network (T1) interface was discarded due to insufficient buffer space. Only frames whose DLCI is a… |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.4.1.1.16 |
.1.3.6.1.4.1.1570.1.5.1
·
1 row entry
·
10 columns
This table monitors and controls the T1-617 Annex-D parameters used by the channel units. There is one table row for every channel unit in every bank. The table is indexed first using the Cisco 90 Series channel bank digroup number, then the channel unit number (1 to 24). For best performance, all of the channel units in a given bank should be set to identical values. These values are typically set using global parameters in the frxDefaultTable instead of directly via this table.
A specific entry in the Cisco 90 Series Management Table.
There is one entry for each Cisco 90 Series channel unit
in the system. There are no entries for unused banks or
empty channel unit slots
There is one entry for each Cisco 90 Series channel unit
in the system. There are no entries for unused banks or
empty channel unit slots
Indexes
frxBankIndex frxChUIndex
| Column | Syntax | OID | ||||
|---|---|---|---|---|---|---|
|
frxPortsInSvc
mandatory
Ports in service. The number of ports on a Cisco 90 Series
channel unit that have one or more active PVCs, as determined by Annex-D. |
Integer32 Constraints: range: 0-4 |
.1.3.6.1.4.1.1570.1.5.1.1.1 |
||||
|
frxMgtT391
mandatory
This controls how often (in seconds) the channel unit
sends an Annex-D poll to the frame relay switch. This is the Annex-D T391 parameter (Typical value 10) |
Integer32r/w Constraints: range: 5-30 |
.1.3.6.1.4.1.1570.1.5.1.1.2 |
||||
|
frxMgtT392
mandatory
This controls how long (in seconds) the channel unit
will wait for a subscriber to send it an Annex-D poll before declaring a link error from the subscriber. This is the Annex-D T392 parameter (Typical value 15) |
Integer32r/w Constraints: range: 5-30 |
.1.3.6.1.4.1.1570.1.5.1.1.3 |
||||
|
frxMgtN391
mandatory
This controls how often (in polls) the channel unit
sends a full status inquiry poll to the frame relay switch instead of a link integrity verification poll. This is the Annex-D N391 parameter (Typical value 6) |
Integer32r/w Constraints: range: 1-255 |
.1.3.6.1.4.1.1570.1.5.1.1.4 |
||||
|
frxMgtN392
mandatory
When more than frxMgtN392 errors are detected in any
frxMgtN393 monitored Annex-D events, the network is declared inactive. This is the Annex-D N392 parameter (Typical value 3) |
Integer32r/w Constraints: range: 1-10 |
.1.3.6.1.4.1.1570.1.5.1.1.5 |
||||
|
frxMgtN393
mandatory
When more than frxMgtN392 errors are detected in any
frxMgtN393 monitored Annex-D events, the network is declared inactive. This is the Annex-D N393 parameter (Typical value 4) |
Integer32r/w Constraints: range: 1-10 |
.1.3.6.1.4.1.1570.1.5.1.1.6 |
||||
|
frxNetLinkErrors
mandatory
Number of signaling link reliability errors from
network. A signaling reliability error is declared whenever the channel units did not receive a reply from the frame relay switch to an Annex-D link integrity poll or fu… |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.5.1.1.7 |
||||
|
frxNetProtErrors
mandatory
Number of signaling protocol errors from network.
A signaling protocol error is declared whenever the channel units receive a reply with incorrect format or sequence numbers from the frame relay switch in response to an… |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.5.1.1.8 |
||||
|
frxNetChInactive
mandatory
Number of times network Annex-D signaling channel
was declared inactive. |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.5.1.1.9 |
||||
|
frxNetChStatus
mandatory
Current status of the Annex-D signaling channel on
the network side of the channel bank. |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.1570.1.5.1.1.10 |
.1.3.6.1.4.1.1570.1.5.2
·
1 row entry
·
4 columns
This table monitors the T1-617 Annex-D link between the channel units and the subscribers. There is one table row for every port on every channel unit in every bank. The table is indexed first using the channel bank digroup number, then the channel unit number (1 to 24), and then the port number (0 to 3).
A specific entry in the Cisco 90 Series Management Port
Table. There is one entry for each port on each
Cisco 90 Series channel unit in the system. There are no
entries for unused banks or empty channel unit
slots.
Table. There is one entry for each port on each
Cisco 90 Series channel unit in the system. There are no
entries for unused banks or empty channel unit
slots.
Indexes
frxBankIndex frxChUIndex frxPortIndex
| Column | Syntax | OID |
|---|---|---|
|
frxPortIndex
mandatory
Which subscriber port on the channel unit is
addressed. Ports are numbered from 0 to 3. Some channel unit types have less than 4 ports. |
Integer32 Constraints: range: 0-3 |
.1.3.6.1.4.1.1570.1.5.2.1.1 |
|
frxPortLinkErrors
mandatory
Number of signaling link reliability errors from
subscriber port. A signaling reliability error is declared whenever the channel units did not receive an Annex-D link integrity poll or full status inquiry poll from the… |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.5.2.1.2 |
|
frxPortProtErrors
mandatory
Number of signaling protocol errors from subscriber
port. A signaling protocol error is declared whenever the channel units receive an Annex-D link integrity poll or full status inquiry poll with incorrect format or seq… |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.5.2.1.3 |
|
frxPortChInactive
mandatory
Number of times the subscriber port Annex-D signaling
channel was declared inactive |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.5.2.1.4 |
.1.3.6.1.4.1.1570.1.6.1
·
1 row entry
·
20 columns
This Cisco 90 Series Port Table contains per-port control and statistics for each of the subscriber ports in the system. The table is indexed first using the Cisco 90 Series channel bank digroup number, then by the channel unit number (1 to 24), and finally by the port number (0-3).
A specific entry in the Cisco 90 Series Port Table. There is
one entry for each port on each Cisco 90 Series channel unit
in the system. There are no entries for unused banks or
empty channel unit slots.
one entry for each port on each Cisco 90 Series channel unit
in the system. There are no entries for unused banks or
empty channel unit slots.
Indexes
frxBankIndex frxChUIndex frxPortIndex
| Column | Syntax | OID | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|
|
frxPortSpeed
mandatory
This is the speed that the channel unit port runs at.
1=56kbps 2=64kbps 3=128kbps 4=144kbps This parameter can only be changed if frxConfigSrc is set to SNMP. |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.1570.1.6.1.1.1 |
||||||||
|
frxPortProtocol
mandatory
This parameter controls what protocol the channel
unit should expect the subscriber to send on the port. 1=Port uses Frame Relay protocol - no encapsulation 2=Port uses PPP protocol - do RFC-1973 encapsulation This … |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.1570.1.6.1.1.2 |
||||||||
|
frxDSLStatus
mandatory
This is the status of the DSL loop to the subscriber.
1=Loop is down. 2=Frx card has achieved physical layer activation with the first BRITE card or the NT1 if there are no BRITE cards. 3=Link is up but Annex-D is sti… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.1570.1.6.1.1.3 |
||||||||
|
frxPVCAssigned
mandatory
Number of PVCs assigned to Subscriber Port as determined
by Annex-D |
Integer32 Constraints: range: 0-8 |
.1.3.6.1.4.1.1570.1.6.1.1.4 |
||||||||
|
frxLastChange
mandatory
Time since DSL went in sync or lost sync in 0.01
second increments. |
RFC1155-SMITimeTicks Textual Convention: RFC1155-SMITimeTicks Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.6.1.1.5 |
||||||||
|
frxBrite
mandatory
Number of BRITE cards downstream. BRITE cards are used
to extend the loop over subscriber loop carrier systems and are detected via a background polling operation. |
Integer32 Constraints: range: 0-6 |
.1.3.6.1.4.1.1570.1.6.1.1.6 |
||||||||
|
frxDSLInOctets
mandatory
Number of octets received from the subscriber DSL
Does not include Annex-D octets |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.6.1.1.7 |
||||||||
|
frxDSLOutOctets
mandatory
Number of octets transmitted to the subscriber DSL.
Does not include Annex-D octets |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.6.1.1.8 |
||||||||
|
frxT1InOctets
mandatory
Number of octets received from the network
directed at this subscriber port |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.6.1.1.9 |
||||||||
|
frxT1OutOctets
mandatory
Number of octets transmitted to the network
from this subscriber port |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.6.1.1.10 |
||||||||
|
frxDSLBadFrames
mandatory
Total number of frames received from this subscriber port
that were discarded. Possible reasons for discard are: Frame contained HDLC abort (7 or more ones in a row) Frame had a CRC error Frame had a non-integr… |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.6.1.1.11 |
||||||||
|
frxDSLHDLCEs
mandatory
Subscriber port Errored Seconds caused by HDLC aborts
(7 or more ones in a row). Total number of seconds in which a frame with an HDLC abort is received from this port. |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.6.1.1.12 |
||||||||
|
frxDSLCRCEs
mandatory
Subscriber port Errored Seconds caused by CRC errors.
Total number of seconds in which a frame with a CRC error is received from this port. |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.6.1.1.13 |
||||||||
|
frxDSLLinkEs
mandatory
Subscriber port Errored Seconds caused by Non-integral
Bytes. Total number of seconds in which a frame with a non-integral number of bytes is received from this port. |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.6.1.1.14 |
||||||||
|
frxDSLFrShEs
mandatory
Subscriber port Errored Seconds caused by Short Frames.
received Total number of seconds in which a frame that is too short (less than 5 bytes) is received from this port. |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.6.1.1.15 |
||||||||
|
frxDSLFrLgEs
mandatory
Subscriber port Errored Seconds caused by Long Frames
received. Total number of seconds in which a frame that is too long (more than 8192 bytes) is received from this port. |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.6.1.1.16 |
||||||||
|
frxDSLDLCIEs
mandatory
Subscriber port Errored Seconds caused by illegal DLCI.
Total number of seconds in which a frame that has a DLCI other than 16 to 23 (or 0) is received from this port. |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.6.1.1.17 |
||||||||
|
frxTxBuf
mandatory
Number of octets in the transmit buffer for this
subscriber port. This data is waiting to be sent to the network (T1). |
Integer32 Constraints: range: 0-65535 |
.1.3.6.1.4.1.1570.1.6.1.1.18 |
||||||||
|
frxRxBuf
mandatory
Number of octets in the receive buffer for this
subscriber port. This data is from the network (T1) and is waiting to be sent to the subscriber port. |
Integer32 Constraints: range: 0-65535 |
.1.3.6.1.4.1.1570.1.6.1.1.19 |
||||||||
|
frxPortNetEs
mandatory
Total number of seconds in which a frame received
from the network (T1) and targeted at this subscriber port was discarded. |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.6.1.1.20 |
.1.3.6.1.4.1.1570.1.6.2
·
1 row entry
·
10 columns
This Cisco 90 Series Circuit Table contains per-virtual-circuit control and statistics for each of the permanent virtual circuits in the system. The table is indexed first using the Cisco 90 Series channel bank digroup number, then by the channel unit number (1 to 24), then by the port number (0-3) and finally by the circuit DLCI number (16 to 23).
A specific entry in the Cisco 90 Series Circuit Table.
There is one entry for each permanent virtual circuit
in the system. There are no entries for unused
banks or empty channel unit slots.
There is one entry for each permanent virtual circuit
in the system. There are no entries for unused
banks or empty channel unit slots.
Indexes
frxBankIndex frxChUIndex frxPortIndex frxPvcIndex
| Column | Syntax | OID | ||||
|---|---|---|---|---|---|---|
|
frxPvcIndex
mandatory
This index is the subscriber loop DLCI number of the
permanent virtual circuit. It ranges from 16 to 23. The corresponding network side DLCI must be assigned in the frame relay switch and communicated to the Cisco 90 Se… |
Integer32 Constraints: range: 16-23 |
.1.3.6.1.4.1.1570.1.6.2.1.1 |
||||
|
frxCktCIR
mandatory
This is the committed information rate (CIR) in bits
per second for the addressed permanent virtual circuit. (Typical value 1536000/#ports). |
Integer32r/w Constraints: range: 0-1544000 |
.1.3.6.1.4.1.1570.1.6.2.1.2 |
||||
|
frxCktBc
mandatory
This is the Committed Burst Size (Bc) in bits for the
addressed permanent virtual circuit. The time interval over which the burst is measured is Bc/CIR. (Typically set to same number as frxCktCIR). |
Integer32r/w Constraints: range: 0-16777215 |
.1.3.6.1.4.1.1570.1.6.2.1.3 |
||||
|
frxCktBe
mandatory
This is the Excess Burst Size (Be) in bits for the
addressed permanent virtual circuit. The time interval over which the excess burst is measured is Be/CIR. (Typical value 1536000). |
Integer32r/w Constraints: range: 0-16777215 |
.1.3.6.1.4.1.1570.1.6.2.1.4 |
||||
|
frxFarEndOpStat
mandatory
This is the status of the far end of the frame relay
permanent virtual circuit (through the frame relay network) as determined by Annex-D. 1=active 2=inactive |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.1570.1.6.2.1.5 |
||||
|
frxCktInOctets
mandatory
The number of input octets from the subscriber port
on the addressed permanent virtual circuit. These octets are destined for the network (T1). |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.6.2.1.6 |
||||
|
frxCktOutOctets
mandatory
The number of output octets to the subscriber port
on the addressed permanent virtual circuit. These octets were received from the network (T1). |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.6.2.1.7 |
||||
|
frxCktInFrames
mandatory
The number of input frames from the subscriber port
on the addressed permanent virtual circuit. These frames are destined for the network (T1). |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.6.2.1.8 |
||||
|
frxCktOutFrames
mandatory
The number of output frames to the subscriber port
on the addressed permanent virtual circuit. These frames were received from the network (T1). |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.6.2.1.9 |
||||
|
frxCktDiscards
mandatory
The number of input frames from the subscriber port
on the addressed permanent virtual circuit that were discarded due to congestion (lack of buffer space or congestion control. |
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.6.2.1.10 |
.1.3.6.1.4.1.1570.1.6.3
·
1 row entry
·
9 columns
This Cisco 90 Series Embedded Operations Channel Table is used to diagnose and sectionalize problems with the subscriber loop. It contains one entry for each of the Cisco 90 Series channel units in the system. The table is indexed first using the Cisco 90 Series channel bank digroup number, then the channel unit number (1 to 24).
A specific entry in the Cisco 90 Series Embedded Operations
Channel Table. There is one entry for each Cisco 90 Series
channel unit in the system. There are no entries for unused
banks or empty channel unit slots
Channel Table. There is one entry for each Cisco 90 Series
channel unit in the system. There are no entries for unused
banks or empty channel unit slots
Indexes
frxBankIndex frxChUIndex
| Column | Syntax | OID | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
frxTestPort
mandatory
This parameter indicates which subscriber port on the
channel unit to test. It has no effect until frxStartTest is set to start the test. Only one port on a given channel unit may be tested at a time. |
Integer32r/w Constraints: range: 0-3 |
.1.3.6.1.4.1.1570.1.6.3.1.1 |
||||||||||||||||
|
frxTestType
mandatory
This parameter indicates the type of test to perform. It
has no effect until frxStartTest is set to start the test. 1=Set up a loopback and run a PN-2047 Bit Error Rate Test. 2=Run a (straightaway) PN-2047 Bit Error Rat… |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.1570.1.6.3.1.2 |
||||||||||||||||
|
frxLoopLoc
mandatory
This parameter indicates the location of the loopback or
the card that will send corrupt CRC. It has no effect until frxStartTest is set to start the test. It has no effect for a BertOnly test. 7=Local Cisco 90 Series … |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.1570.1.6.3.1.3 |
||||||||||||||||
|
frxLoopCh
mandatory
This parameter indicates which channels to use for the
loopbackOnly and localLoopAllPorts test. It has no effect until frxStartTest is set to start the test. Note that the loopbackAndBert test always loops all channels … |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.1570.1.6.3.1.4 |
||||||||||||||||
|
frxStartTest
mandatory
This parameter is used to start and stop the test.
frxTestPort, frxTestType, frxLoopLoc, and frxLoopCh should be set up prior to starting the test. 1=stop test. 2=start test. |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.1570.1.6.3.1.5 |
||||||||||||||||
|
frxBertRst
mandatory
This parameter may be used during a LoopbackAndBert test
or a BertOnly test to reset the frxBertBE counter. It must be returned to the normal posiion to allow errors to be counted. 1=normal. 2=Reset BERT counter. |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.1570.1.6.3.1.6 |
||||||||||||||||
|
frxBertBE
mandatory
BERT test block errors
|
RFC1155-SMICounter Textual Convention: RFC1155-SMICounter Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.6.3.1.7 |
||||||||||||||||
|
frxBertTestTime
mandatory
BERT test time in 0.01 second increments
|
RFC1155-SMITimeTicks Textual Convention: RFC1155-SMITimeTicks Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.1570.1.6.3.1.8 |
||||||||||||||||
|
frxTestInProg
mandatory
Test in progress (1); Normal operation (2)
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.1570.1.6.3.1.9 |
.1.3.6.1.4.1.1570.1.6.4
·
1 row entry
·
7 columns
This table contains the U-interface Performance Monitoring Thresholds and Alarms for each of the subscriber loops in the system and for any BRITE cards extending those loops (e.g. using Subscriber Loop Carrier systems) The table is indexed first using the Cisco 90 Series channel bank digroup number, then the channel unit number (1 to 24), then the port number (0, 1, etc) and finally the location number (the BRITE card number (1 to 6) or 7 for local parameters in the Cisco 90 Series card). These registers are defined by Bellcore TR-TSY-000829.
A specific entry in the U-interface Performance Monitoring
Threshold table. There is one entry for each port on each
Cisco 90 Series channel unit in the system and one entry for
each BRITE card extending those ports. …
Threshold table. There is one entry for each port on each
Cisco 90 Series channel unit in the system and one entry for
each BRITE card extending those ports. …
Indexes
frxBankIndex frxChUIndex frxPortIndex frxPAddrIndex
| Column | Syntax | OID | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
frxPAddrIndex
mandatory
This is the physical location where the performance
monitoring takes place. It may be set to localFrx(7) to access and control PM values local to the Cisco 90 Series channel unit. If there are BRITE cards in the subscr… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.1570.1.6.4.1.1 |
||||||||||||||
|
frxChEsTh
mandatory
Current Hour Errored Seconds threshold. This
threshold is used for both the transmit and receive directions. When errors are detected that exceed this threshold and the corresponding bit in the frxAlertMask register is … |
Integer32r/w Constraints: range: 1-3600 |
.1.3.6.1.4.1.1570.1.6.4.1.2 |
||||||||||||||
|
frxCdEsTh
mandatory
Current Day Errored Seconds threshold. This
threshold is used for both the transmit and receive directions. When errors are detected that exceed this threshold and the corresponding bit in the frxAlertMask register is 0… |
Integer32r/w Constraints: range: 1-65535 |
.1.3.6.1.4.1.1570.1.6.4.1.3 |
||||||||||||||
|
frxChSesTh
mandatory
Current Hour Severely Errored Seconds threshold. This
threshold is used for both the transmit and receive directions. When errors are detected that exceed this threshold and the corresponding bit in the frxAlertMask reg… |
Integer32r/w Constraints: range: 1-3600 |
.1.3.6.1.4.1.1570.1.6.4.1.4 |
||||||||||||||
|
frxCdSesTh
mandatory
Current Day Severely Errored Seconds threshold. This
threshold is used for both the transmit and receive directions. When errors are detected that exceed this threshold and the corresponding bit in the frxAlertMask regi… |
Integer32r/w Constraints: range: 1-65535 |
.1.3.6.1.4.1.1570.1.6.4.1.5 |
||||||||||||||
|
frxAlertMask
mandatory
8-bit Alert Mask register. One bit for each threshold in
both directions. When set to 1, the corresponding threshold crossing is ignored. When set to 0, the corresponding threshold crossing is indicated in frxThCond an… |
Integer32r/w Constraints: range: 0-255 |
.1.3.6.1.4.1.1570.1.6.4.1.6 |
||||||||||||||
|
frxThCond
mandatory
8-bit Threshold Condition register. One bit for each
threshold in both directions. Set to 1 if the threshold is exceeded and the corresponding bit in the frxAlertMask register is set to 0. Only set to 0 by the SNMP man… |
Integer32r/w Constraints: range: 0-255 |
.1.3.6.1.4.1.1570.1.6.4.1.7 |
.1.3.6.1.4.1.1570.1.6.5
·
1 row entry
·
36 columns
This table contains the U-interface Performance Monitoring Statistics for each of the subscriber loops in the system and for any BRITE cards extending those loops (e.g. using Subscriber Loop Carrier systems) The table is indexed first using the Cisco 90 Series channel bank digroup number, then the channel unit number (1 to 24), then the port number (0, 1, etc) and finally the location number (the BRITE card number (1 to 6) or 7 for local parameters in the Cisco 90 Series card). These registers are defined by Bellcore TR-TSY-000829.
A specific entry in the U-interface Performance Monitoring
Statistics table. There is one entry for each port on each
Cisco 90 Series channel unit in the system and one entry for
each BRITE card extending those ports. …
Statistics table. There is one entry for each port on each
Cisco 90 Series channel unit in the system and one entry for
each BRITE card extending those ports. …
Indexes
frxBankIndex frxChUIndex frxPortIndex frxPAddrIndex
| Column | Syntax | OID | ||||
|---|---|---|---|---|---|---|
|
frxResetPM
mandatory
Reset all of the performance monitoring statistics on the
specified Cisco 90 Series channel unit or BRITE card. 1=Normal. 2=Reset. There is no need to set this register back to Normal after doing a reset. |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.1570.1.6.5.1.1 |
||||
|
frxPMtype
mandatory
Determines if the Cisco 90 Series channel unit or the downstream
BRITE cards is doing segmented or path performance monitoring as specified in Bellcore document TR-NWT-000397. Only segmented performance monitoring shou… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.1570.1.6.5.1.2 |
||||
|
frxChEsTx
mandatory
Current Hour Errored Seconds - Transmit direction.
Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical … |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.3 |
||||
|
frxChEsRx
mandatory
Current Hour Errored Seconds - Receive direction.
Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical li… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.4 |
||||
|
frxPhEsTx
mandatory
Previous Hour Errored Seconds - Transmit direction.
Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.5 |
||||
|
frxPhEsRx
mandatory
Previous Hour Errored Seconds - Receive direction.
Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical l… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.6 |
||||
|
frxH2EsTx
mandatory
Errored Seconds 2 hours ago - Transmit direction.
Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical l… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.7 |
||||
|
frxH2EsRx
mandatory
Errored Seconds 2 hours ago - Receive direction.
Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical lin… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.8 |
||||
|
frxH3EsTx
mandatory
Errored Seconds 3 hours ago - Transmit direction.
Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical l… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.9 |
||||
|
frxH3EsRx
mandatory
Errored Seconds 3 hours ago - Receive direction.
Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical lin… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.10 |
||||
|
frxH4EsTx
mandatory
Errored Seconds 4 hours ago - Transmit direction.
Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical l… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.11 |
||||
|
frxH4EsRx
mandatory
Errored Seconds 4 hours ago - Receive direction.
Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical lin… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.12 |
||||
|
frxH5EsTx
mandatory
Errored Seconds 5 hours ago - Transmit direction.
Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical l… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.13 |
||||
|
frxH5EsRx
mandatory
Errored Seconds 5 hours ago - Receive direction.
Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical lin… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.14 |
||||
|
frxH6EsTx
mandatory
Errored Seconds 6 hours ago - Transmit direction.
Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical l… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.15 |
||||
|
frxH6EsRx
mandatory
Errored Seconds 6 hours ago - Receive direction.
Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical lin… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.16 |
||||
|
frxH7EsTx
mandatory
Errored Seconds 7 hours ago - Transmit direction.
Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical l… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.17 |
||||
|
frxH7EsRx
mandatory
Errored Seconds 7 hours ago - Receive direction.
Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical lin… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.18 |
||||
|
frxH8EsTx
mandatory
Errored Seconds 8 hours ago - Transmit direction.
Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical l… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.19 |
||||
|
frxH8EsRx
mandatory
Errored Seconds 8 hours ago - Receive direction.
Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical lin… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.20 |
||||
|
frxCdEsTx
mandatory
Current Day Errored Seconds - Transmit direction.
Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical l… |
Integer32 Constraints: range: 0-65535 |
.1.3.6.1.4.1.1570.1.6.5.1.21 |
||||
|
frxCdEsRx
mandatory
Current Day Errored Seconds - Receive direction.
Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical lin… |
Integer32 Constraints: range: 0-65535 |
.1.3.6.1.4.1.1570.1.6.5.1.22 |
||||
|
frxPdEsTx
mandatory
Previous Day Errored Seconds - Transmit direction.
Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical … |
Integer32 Constraints: range: 0-65535 |
.1.3.6.1.4.1.1570.1.6.5.1.23 |
||||
|
frxPdEsRx
mandatory
Previous Day Errored Seconds - Receive direction.
Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical li… |
Integer32 Constraints: range: 0-65535 |
.1.3.6.1.4.1.1570.1.6.5.1.24 |
||||
|
frxChSesTx
mandatory
Current Hour Severely Errored Seconds - Transmit direction.
Transmit is data from the network towards the customer. Severely Errored Seconds are seconds in which three or more block errors occur. These errors are measu… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.25 |
||||
|
frxChSesRx
mandatory
Current Hour Severely Errored Seconds - Receive direction.
Receive is data from the customer towards the network. Severely Errored Seconds are seconds in which three or more block errors occur. These errors are measure… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.26 |
||||
|
frxPhSesTx
mandatory
Previous Hour Severely Errored Seconds - Transmit direction.
Transmit is data from the network towards the customer. Severely Errored Seconds are seconds in which three or more block errors occur. These errors are meas… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.27 |
||||
|
frxPhSesRx
mandatory
Previous Hour Severely Errored Seconds - Receive direction.
Receive is data from the customer towards the network. Severely Errored Seconds are seconds in which three or more block errors occur. These errors are measur… |
Integer32 Constraints: range: 0-3600 |
.1.3.6.1.4.1.1570.1.6.5.1.28 |
||||
|
frxCdSesTx
mandatory
Current Day Severely Errored Seconds - Transmit direction.
Transmit is data from the network towards the customer. Severely Errored Seconds are seconds in which three or more block errors occur. These errors are measur… |
Integer32 Constraints: range: 0-65535 |
.1.3.6.1.4.1.1570.1.6.5.1.29 |
||||
|
frxCdSesRx
mandatory
Current Day Severely Errored Seconds - Receive direction.
Receive is data from the customer towards the network. Severely Errored Seconds are seconds in which three or more block errors occur. These errors are measured… |
Integer32 Constraints: range: 0-65535 |
.1.3.6.1.4.1.1570.1.6.5.1.30 |
||||
|
frxPdSesTx
mandatory
Previous Day Severely Errored Seconds - Transmit direction.
Transmit is data from the network towards the customer. Severely Errored Seconds are seconds in which three or more block errors occur. These errors are measu… |
Integer32 Constraints: range: 0-65535 |
.1.3.6.1.4.1.1570.1.6.5.1.31 |
||||
|
frxPdSesRx
mandatory
Previous Day Severely Errored Seconds - Receive direction.
Receive is data from the customer towards the network. Severely Errored Seconds are seconds in which three or more block errors occur. These errors are measure… |
Integer32 Constraints: range: 0-65535 |
.1.3.6.1.4.1.1570.1.6.5.1.32 |
||||
|
frxChBeTx
mandatory
Current Hour Block Errors - Transmit direction.
Transmit is data from the network towards the customer. Block errors are 12 millisecond time periods in which a physical link level (e.g. DSL CRC or BPV) error occurs. The… |
Integer32 Constraints: range: 0-65535 |
.1.3.6.1.4.1.1570.1.6.5.1.33 |
||||
|
frxChBeRx
mandatory
Current Hour Block Errors - Receive direction.
Receive is data from the customer towards the network. Block errors are 12 millisecond time periods in which a physical link level (e.g. DSL CRC or BPV) error occurs. These… |
Integer32 Constraints: range: 0-65535 |
.1.3.6.1.4.1.1570.1.6.5.1.34 |
||||
|
frxPhBeTx
mandatory
Previous Hour Block Errors - Transmit direction.
Transmit is data from the network towards the customer. Block errors are 12 millisecond time periods in which a physical link level (e.g. DSL CRC or BPV) error occurs. Th… |
Integer32 Constraints: range: 0-65535 |
.1.3.6.1.4.1.1570.1.6.5.1.35 |
||||
|
frxPhBeRx
mandatory
Previous Hour Block Errors - Receive direction.
Receive is data from the customer towards the network. Block errors are 12 millisecond time periods in which a physical link level (e.g. DSL CRC or BPV) error occurs. Thes… |
Integer32 Constraints: range: 0-65535 |
.1.3.6.1.4.1.1570.1.6.5.1.36 |