CISCO-WIRELESS-IF-MIB Table View

This table provides facilities to establish loopback points in the
radio hardware to exercise various sections of the hardware.

This table provides facilities to redirect a portion of the signal
being processed by a DSP to a scope port on the radio. An
oscilloscope may be connected to the scope port to analyze the 
signal.

This table contains information about the radio common to both 
the transmit and receive sides.

This table contains information about the currently configured
physical layer.  These configuration paramters must match the 
    corresponding configuration parameter at the remote end for
    the wireless link to be established.

This table contains information about the radio PHY quality 
control parameters. Note that the parameters in this table are 
automatically determined by the parameters configured in the 
cwrRadioPhyTable. These parameters may further be used to tune 
the characteristics when needed.

This provides information on the number of byte
detected and corrected by the ARQ engine.
The ARQ engine can correct up to 9 consecutive byte errors.
This table keeps a count of the number of byte errors corrected
over time.
The values in this table are cumulated from link power up.

This table contains information about the state of the 
radio frequency resources used by the radio link.

This table contains information about the state of the 
intermediate frequency subsystem on the wireless radio.

This table contains threshold values that are the trigger points 
for controlling the collection of the Link Metrics such as 
Codeword Errored Seconds and others.

This table contains metrics used to measure the quality of the 
radio link identified by the ifIndex. The metrics in this table 
are cumulated since the last time the system powered up.

This table contains metrics collected over the duration of 
24 hours.
This table is updated once every day for 32 days. Therefore, this
table will have a maximum of 32 entries that provide cumulative 
status of the link, identified by ifIndex.

This table contains metrics collected over the duration of one 
hour.
This table will have a maximum of 24 entries providing cumulative 
status of the link, identified by ifIndex, over the past 24 hours.
This table is updated once every hour.

This table contains metrics collected over the duration of one 
minute.
This table will have a maximum of 60 entries providing cumulative 
status of the link, identified by ifIndex, over the past 60 minutes.
This table is updated once every minute.

This table contains metrics collected over a duration of 1 second.
The data in this table is derived directly from the hardware.
          
This table will have a maximum of 60 entries providing cumulative 
status of the link, identified by ifIndex, over the past 60 seconds.
          
This table is updated once every second.

This table contains information about histograms configured in
hardware. When data is collected it will be stored in histogram
bins as follows:
All values (X < cwrStartBinValue) will be kept in the first
histogram bin.
Subsequent values will be distributed in the bins based on the
cwrBinDelta. Last bin, will contain all values
(X > (cwrStartBinValue + (cwrNumBins - 2) * cwrBinDelta)),
i.e. any value that is greater than that may be stored in the
last bin.

This table contains histogram Summary collected based on the
specifications in the cwrHistCtrlTable.

This table contains histogram values collected based on the
specifications in the cwrHistCtrlTable.

This table provides facilities to establish thresholds for the 
radio signals analyzed on the radio interface. A threshold 
identified in this table may be used to trigger a timeline 
capture in the cwrTlTable.

This table contains information about timelines configured in
hardware. The number of data values captured for each timeline
is configured by setting the variable cwrTlNumDataValues. 
The captured data values can be retreived by reading the 
cwrTlDataTable.

This table contains Timeline Summary collected based on the
specifications in the cwrTlCtrlTable.

This table contains data values collected for the timelines
specified in the cwrTlCtrlTable.  The number of data values 
displayed for each timeline is determined by the value specified
for cwrTlNumDataValues in cwrTlCtrlTable.

This table contains information about the snapshots configured in
hardware. When data is collected it will be stored in
cwrSnapDataTable.

This table contains summary information for captured snapshots
defined in cwrSnapshotCtrlTable.

This table contains snapshot values collected based on the
specifications in the cwrSnapshotCtrlTable.

This table contains information about the antenns available for
use.

This table provides information about the last trap that was
generated on this interface.