cwrCableLoss
CISCO-WIRELESS-IF-MIB ·
.1.3.6.1.4.1.9.9.136.1.3.2.1.8
Object
column
r/w
dB - decibel Integer32
This object represents the measured loss in signal power in dB that is imposed by the cable connecting the radio to the antenna head. This value enables the hardware to compensate for the cable loss by adjusting the gain appropriately. A value of 0 represents no degradation in signal due to the cable. This cable loss applies to the transmit antenna identified by cwrTxRfIndex.
Context
- MIB
- CISCO-WIRELESS-IF-MIB
- OID
.1.3.6.1.4.1.9.9.136.1.3.2.1.8- Type
- column
- Access
- readwrite
- Status
- current
- Units
- dB - decibel
- Parent
- cwrRadioPhyEntry
- Table
- cwrRadioPhyTable
- Siblings
- 10
Syntax
dB - decibel Integer32
Values & Constraints
Object Constraints
range: 0-50
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cwrNumRxAntenna This object specifies the number of antennas to be used to receive
the wireless transmissions. | column | Integer32 | .1.3.6.1.4.1.9.9.136.1.3.2.1.1 |
| cwrCableLossDiversity This object represents the measured loss in signal power
in dB that is imposed by the cable connecting the radio
to the antenna head.
This value enables the hardware to compensa… | column | dB - decibel Integer32 | .1.3.6.1.4.1.9.9.136.1.3.2.1.10 |
| cwrBurstSize This object defines the time duration of the data burst sent
over the air. The burst size is dependant on the capability of
the ODU which is represented by the cwrBurstSizeGroup… | column | Enumeration | .1.3.6.1.4.1.9.9.136.1.3.2.1.11 |
| cwrBandwidth This object specifies the bandwidth to use. Given bandwidth, the
actual throughput of the radio link is determined by the
cwrThroughput setting. | column | Hz Integer32 | .1.3.6.1.4.1.9.9.136.1.3.2.1.2 |
| cwrThroughput This represents an throughput expected of the identified radio
link. There are 3 possible settings. The settings provide a
tradeoff between bandwidth and the reliability of the … | column | Enumeration | .1.3.6.1.4.1.9.9.136.1.3.2.1.3 |
| cwrOperatingBand This object represents the portion of the frequency spectrum in
which the radio PHY will operate.
bandUNII(1) - The U-NII (Unlicensed National Information
… | column | Enumeration | .1.3.6.1.4.1.9.9.136.1.3.2.1.4 |
| cwrTxFrequency This object represents the center frequency that will be used to
transmit data over the radio PHY. The specified transmit
frequency must match the operating band and the capabili… | column | 10Khz Integer32 | .1.3.6.1.4.1.9.9.136.1.3.2.1.5 |
| cwrRxFrequency This object represents the center frequency that will be used to
receive transmissions over the radio PHY. The specified receive
frequency must match the operating band and the ca… | column | 10Khz Integer32 | .1.3.6.1.4.1.9.9.136.1.3.2.1.6 |
| cwrTxPower This object represents the power that the antenna will transmit.
The minimum average transmit power for the U-NII or MMDS band is
0.01 microwatts (-80 dBm). Maximum average transm… | column | dBm - decibel milliwatts Integer32 | .1.3.6.1.4.1.9.9.136.1.3.2.1.7 |
| cwrOpStatus This represents the current state of a radio Link.
notOperational(1): The link is not operational.
selftest(2) : Power on self test in progress
download(3): Image d… | column | Enumeration | .1.3.6.1.4.1.9.9.136.1.3.2.1.9 |