cwrThroughput
CISCO-WIRELESS-IF-MIB ·
.1.3.6.1.4.1.9.9.136.1.3.2.1.3
Object
column
r/w
Enumeration
This represents an throughput expected of the identified radio
link. There are 3 possible settings. The settings provide a
tradeoff between bandwidth and the reliability of the
radio link. The settings are:
high(1): For a high throughput. The radio hardware will be
configured such that it, favors throughput over
error correction. It may not be able to correct
all received errors.
medium(2): This is a balance between high and low.
low(3): The radio hardware is configured such that it
trades off throughput for latency and error
correction. It tries its very
best to correct errors it detects.
Context
- MIB
- CISCO-WIRELESS-IF-MIB
- OID
.1.3.6.1.4.1.9.9.136.1.3.2.1.3- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- cwrRadioPhyEntry
- Table
- cwrRadioPhyTable
- Siblings
- 10
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | high |
2 | medium |
3 | low |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cwrNumRxAntenna This object specifies the number of antennas to be used to receive
the wireless transmissions. | column | Integer32 | .1.3.6.1.4.1.9.9.136.1.3.2.1.1 |
| cwrCableLossDiversity This object represents the measured loss in signal power
in dB that is imposed by the cable connecting the radio
to the antenna head.
This value enables the hardware to compensa… | column | dB - decibel Integer32 | .1.3.6.1.4.1.9.9.136.1.3.2.1.10 |
| cwrBurstSize This object defines the time duration of the data burst sent
over the air. The burst size is dependant on the capability of
the ODU which is represented by the cwrBurstSizeGroup… | column | Enumeration | .1.3.6.1.4.1.9.9.136.1.3.2.1.11 |
| cwrBandwidth This object specifies the bandwidth to use. Given bandwidth, the
actual throughput of the radio link is determined by the
cwrThroughput setting. | column | Hz Integer32 | .1.3.6.1.4.1.9.9.136.1.3.2.1.2 |
| cwrOperatingBand This object represents the portion of the frequency spectrum in
which the radio PHY will operate.
bandUNII(1) - The U-NII (Unlicensed National Information
… | column | Enumeration | .1.3.6.1.4.1.9.9.136.1.3.2.1.4 |
| cwrTxFrequency This object represents the center frequency that will be used to
transmit data over the radio PHY. The specified transmit
frequency must match the operating band and the capabili… | column | 10Khz Integer32 | .1.3.6.1.4.1.9.9.136.1.3.2.1.5 |
| cwrRxFrequency This object represents the center frequency that will be used to
receive transmissions over the radio PHY. The specified receive
frequency must match the operating band and the ca… | column | 10Khz Integer32 | .1.3.6.1.4.1.9.9.136.1.3.2.1.6 |
| cwrTxPower This object represents the power that the antenna will transmit.
The minimum average transmit power for the U-NII or MMDS band is
0.01 microwatts (-80 dBm). Maximum average transm… | column | dBm - decibel milliwatts Integer32 | .1.3.6.1.4.1.9.9.136.1.3.2.1.7 |
| cwrCableLoss This object represents the measured loss in signal power in
dB that is imposed by the cable connecting the radio to the
antenna head.
This value enables the hardware to compensa… | column | dB - decibel Integer32 | .1.3.6.1.4.1.9.9.136.1.3.2.1.8 |
| cwrOpStatus This represents the current state of a radio Link.
notOperational(1): The link is not operational.
selftest(2) : Power on self test in progress
download(3): Image d… | column | Enumeration | .1.3.6.1.4.1.9.9.136.1.3.2.1.9 |