cwrOpStatus
CISCO-WIRELESS-IF-MIB ·
.1.3.6.1.4.1.9.9.136.1.3.2.1.9
Object
column
Enumeration
This represents the current state of a radio Link.
notOperational(1): The link is not operational.
selftest(2) : Power on self test in progress
download(3): Image download is in progress.
txOnly(4): The radio link will switch to this state if
the radio link is configured for transmit only.
acquiring(5): Attempting to sync up with the far end transmitter.
receiveUp(6): The receive side of the radio link has successfully
sync'ed up with remote end.
transmitUp(7): Transmit side of the radio link is up and running.
linkOperational(8): The radio link is ready for duplex
communication.
Context
- MIB
- CISCO-WIRELESS-IF-MIB
- OID
.1.3.6.1.4.1.9.9.136.1.3.2.1.9- Type
- column
- Access
- readonly
- Status
- current
- Parent
- cwrRadioPhyEntry
- Table
- cwrRadioPhyTable
- Siblings
- 10
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | notOperational |
2 | selftest |
3 | download |
4 | txOnly |
5 | acquiring |
6 | receiveUp |
7 | transmitUp |
8 | linkOperational |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cwrNumRxAntenna This object specifies the number of antennas to be used to receive
the wireless transmissions. | column | Integer32 | .1.3.6.1.4.1.9.9.136.1.3.2.1.1 |
| cwrCableLossDiversity This object represents the measured loss in signal power
in dB that is imposed by the cable connecting the radio
to the antenna head.
This value enables the hardware to compensa… | column | dB - decibel Integer32 | .1.3.6.1.4.1.9.9.136.1.3.2.1.10 |
| cwrBurstSize This object defines the time duration of the data burst sent
over the air. The burst size is dependant on the capability of
the ODU which is represented by the cwrBurstSizeGroup… | column | Enumeration | .1.3.6.1.4.1.9.9.136.1.3.2.1.11 |
| cwrBandwidth This object specifies the bandwidth to use. Given bandwidth, the
actual throughput of the radio link is determined by the
cwrThroughput setting. | column | Hz Integer32 | .1.3.6.1.4.1.9.9.136.1.3.2.1.2 |
| cwrThroughput This represents an throughput expected of the identified radio
link. There are 3 possible settings. The settings provide a
tradeoff between bandwidth and the reliability of the … | column | Enumeration | .1.3.6.1.4.1.9.9.136.1.3.2.1.3 |
| cwrOperatingBand This object represents the portion of the frequency spectrum in
which the radio PHY will operate.
bandUNII(1) - The U-NII (Unlicensed National Information
… | column | Enumeration | .1.3.6.1.4.1.9.9.136.1.3.2.1.4 |
| cwrTxFrequency This object represents the center frequency that will be used to
transmit data over the radio PHY. The specified transmit
frequency must match the operating band and the capabili… | column | 10Khz Integer32 | .1.3.6.1.4.1.9.9.136.1.3.2.1.5 |
| cwrRxFrequency This object represents the center frequency that will be used to
receive transmissions over the radio PHY. The specified receive
frequency must match the operating band and the ca… | column | 10Khz Integer32 | .1.3.6.1.4.1.9.9.136.1.3.2.1.6 |
| cwrTxPower This object represents the power that the antenna will transmit.
The minimum average transmit power for the U-NII or MMDS band is
0.01 microwatts (-80 dBm). Maximum average transm… | column | dBm - decibel milliwatts Integer32 | .1.3.6.1.4.1.9.9.136.1.3.2.1.7 |
| cwrCableLoss This object represents the measured loss in signal power in
dB that is imposed by the cable connecting the radio to the
antenna head.
This value enables the hardware to compensa… | column | dB - decibel Integer32 | .1.3.6.1.4.1.9.9.136.1.3.2.1.8 |