cwrArqDataLatency
CISCO-WIRELESS-IF-MIB ·
.1.3.6.1.4.1.9.9.136.1.4.1.1.3
Object
column
r/w
milliseconds Integer32
This object specifies the expected latency values for data. Reducing the latency, provides the ARQ engine less time to correct codeword errors. So if latency is reduced sufficiently, the data throughput will get effected. Also note that the latency values on both ends of the link should be kept identical, else the data throughput will be effected.
Context
- MIB
- CISCO-WIRELESS-IF-MIB
- OID
.1.3.6.1.4.1.9.9.136.1.4.1.1.3- Type
- column
- Access
- readwrite
- Status
- current
- Units
- milliseconds
- Parent
- cwrPhyQualityEntry
- Table
- cwrPhyQualityTable
- Siblings
- 8
Syntax
milliseconds Integer32
Values & Constraints
Object Constraints
range: 1-2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cwrArqPctBw This object specifies the percentage of the total radio PHY
bandwidth available to the ARQ engine. Some or all of this
allocated bandwidth is used to when detected errors are
c… | column | 0.01 percent Integer32 | .1.3.6.1.4.1.9.9.136.1.4.1.1.1 |
| cwrArqVoiceLatency This object identifies the latency value for voice data. | column | milliseconds Integer32 | .1.3.6.1.4.1.9.9.136.1.4.1.1.2 |
| cwrArqBurstSize This object specifies the maximum number of consecutive ARQ
codewords that will be transmitted. ARQ codewords are
transmitted for error correction. When an ARQ codeword
is tran… | column | Integer32 | .1.3.6.1.4.1.9.9.136.1.4.1.1.4 |
| cwrArqTypicalBitRate This object specifies the typical error free bit rate that
is possible on this link given the current configuration as
specified in the cwrRadioPhyTable. If the radio channel
i… | column | bits/sec Integer32 | .1.3.6.1.4.1.9.9.136.1.4.1.1.5 |
| cwrArqMinBitRate This object specifies the minimum error free bit rate
that is supported on this link given the current
configuration as specified in the
cwrRadioPhyTable and the settings in thi… | column | bits/sec Integer32 | .1.3.6.1.4.1.9.9.136.1.4.1.1.6 |
| cwrArqMaxLatencyJitter This object specifies the maximum latency jitter introduced
by the ARQ engine, based on the settings defined
in this table. | column | microseconds Integer32 | .1.3.6.1.4.1.9.9.136.1.4.1.1.7 |
| cwrArqReset This object when set to true will force the PHY quality
parameters to be reset from the cwrRadioPhyTable.
Reading this object will always return false. This is useful
when arbitra… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.136.1.4.1.1.8 |
| cwrArqOn This object when set to true will enable the Automatic Repeat
Query subsystem. Disabling the ARQ subsystem disables a major
error correction mechanism of the radio, due to which… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.136.1.4.1.1.9 |