TIMETRA-PTP-MIB Table View

Table-centric layout grouping table, row, and column objects.

Tables
21
Rows
21
Columns
347
.1.3.6.1.4.1.6527.3.1.2.74.2.3 · 1 row entry · 24 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpPeerConfigTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpPeerConfigTable'
The tmnxPtpPeerConfigTable consists of peer configuration information.
tmnxPtpPeerConfigEntry row .1.3.6.1.4.1.6527.3.1.2.74.2.3.1
The tmnxPtpPeerConfigEntry contains information pertaining to an
individual PTP 1588 peer.

Individual PTP peers are identified by the virtual router identifier
and IP address of the peer PTP clock.
…
Column Syntax OID
The value of tmnxPtpPeerIpAddrType specifies the type of address of
the PTP 1588 peer. This object represents the first index in the
table.
INET-ADDRESS-MIBInetAddressType
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.1
The value of tmnxPtpPeerIpAddress specifies the address of the PTP
1588 peer. This object represents the second index in the table.
INET-ADDRESS-MIBInetAddress
Constraints:
range: 16-16
range: 4-4
range: 0-0
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.2
The value of tmnxPtpPeerRowStatus specifies the row status of the PTP
1588 peer.

This object controls the creation and deletion of peer PTP grandmaster
and boundary clocks that may provide timing to the l…
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.3
The value of tmnxPtpPeerLastChanged indicates the time, since system
startup, that the PTP 1588 peer was created or modified.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.4
The value of tmnxPtpPeerAdminState specifies the administrative state
of the PTP 1588 peer, that is, whether or not the peer will be used by
the Precision Time Protocol (PTP).
TIMETRA-TC-MIBTmnxAdminStater/w
Type Values:
1noop
2inService
3outOfService
Description:
The TmnxAdminState data type is an enumerated integer that describes
the values used to identify the administratively desired state of
functional modules.
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.5
The value of tmnxPtpPeerPortState indicates the current state of the
PTP port used when communicating with the remote peer.

The value of this object corresponds to the portDS.portState data set
member def…
TmnxPtpPortState
Type Values:
0notApplicable
1initializing
2faulty
3disabled
4listening
5preMaster
6master
7passive
8uncalibrated
9slave
Description:
TmnxPtpPortState indicates the operational state of a PTP port.
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.6
The value of tmnxPtpPeerLocalPriority specifies the local priority
used to choose between PTP masters in the Best Master Clock Algorithm
(BMCA). This object is only relevant when tmnxPtpClockProfile is set
to 'g8265dot1…
TmnxPtpPriorityr/w
Constraints:
range: 1-255
Description:
The Precision Time Protocol (PTP) priority used both for the value to
advertise in the Announce messages and for the local clock value in
data set comparisons.

It is used by the Best Master Clock Algorithm to…
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.7
The value of tmnxPtpPeerRemoteMaster indicates whether or not the peer
is configured as a remote grandmaster or boundary clock that may
provide timing information to the local clock.

If tmnxPtpClockClockT…
SNMPv2-TCTruthValuer/w
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.8
The value of tmnxPtpPeerRemoteSlave specifies whether or not the peer
is acting as a remote slave or boundary clock that may be receiving
timing information from the local clock. Remote slave clocks are
learned by the …
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.9
The value of tmnxPtpPeerClockId indicates the clock identity of the
peer.
TmnxPtpClockIdentity
Type Constraints:
range: 8
Description:
TmnxPtpClockIdentity specifies the unique identifier used to identify
a network element participating in the Precision Time Protocol (PTP).
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.10
The value of tmnxPtpPeerLocalPortNumber indicates the PTP port number
assigned by the local clock and used when communicating with the
remote clock.

If tmnxPtpClockClockType is either 'ordinarySlave (1)' …
TmnxPtpPortNumber
Type Constraints:
range: 0..65534
Description:
TmnxPtpPortNumber specifies a number which identifies a logical access
point of a clock for PTP communications to the communications network.

A PTP ordinary clock has exactly one PTP port, with port number 1.…
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.11
The value of tmnxPtpPeerRemotePortNumber indicates the PTP port number
used by the remote peer when communicating with the local clock.
TmnxPtpPortNumber
Type Constraints:
range: 0..65534
Description:
TmnxPtpPortNumber specifies a number which identifies a logical access
point of a clock for PTP communications to the communications network.

A PTP ordinary clock has exactly one PTP port, with port number 1.…
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.12
The value of tmnxPtpPeerTxTimeStampPoint indicates the reference point
used to generate the PTP timestamp for the last transmitted PTP event
packet. If no event packets have been transmitted, the value is
'unknown(0)'.…
TmnxPtpTimeStampReferencePoint
Type Values:
0unknown
1port
2cpm
Description:
TmnxPtpTimeStampReferencePoint indicates the reference point where a
PTP event packet is timestamped in the SROS system:
unknown (0) - The reference point for the PTP timestamp has not yet
been deter…
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.13
The value of tmnxPtpPeerLastTxPortId along with
tmnxPtpPeerLastTxPortEncapType and tmnxPtpPeerLastTxPortEncapValue
indicates the last port used to transmit PTP packets to the PTP peer.
If no packets have been transmitte…
TIMETRA-TC-MIBTmnxPortID
Description:
A portid is a unique 32 bit number with special encoding.

Refer to TIMETRA-CHASSIS-MIB::tmnxChassisPortIdScheme for a
description of the various port mapping schemes used by the system for
physical ports and …
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.14
The value of tmnxPtpPeerLastTxPortEncapType along with
tmnxPtpPeerLastTxPortId and tmnxPtpPeerLastTxPortEncapValue indicates
the last port used to transmit PTP packets to the PTP peer.
TIMETRA-PORT-MIBTmnxPortEncapType
Type Values:
0unknown
1nullEncap
2qEncap
3mplsEncap
4bcpNullEncap
5bcpDot1qEncap
6ipcpEncap
7frEncap
8pppAutoEncap
9atmEncap
10qinqEncap
11wanMirrorEncap
12ciscoHDLCEncap
13cemEncap
14reserved14
15rawEncap
16cellularEncap
17wlanEncap
Description:
The type of encapsulation protocol configured on a port's network
interface.

When the encap type has a value of 'nullEncap',
frames received will not carry any tags
or labels and as a result only one service …
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.15
The value of tmnxPtpPeerLastTxPortEncapValue along with
tmnxPtpPeerLastTxPortId and tmnxPtpPeerLastTxPortEncapType indicates
the last port used to transmit PTP packets to the PTP peer.
TIMETRA-TC-MIBTmnxEncapVal
Description:
The value of the label used to identify the entity using the specified
encapsulation value on a specific port.

The format of this object depends on the encapsulation type defined on
this port.

When…
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.16
The value of tmnxPtpPeerRxTimeStampPoint indicates the reference point
used to generate the PTP timestamp for the last received PTP event
packet. If no event packets have been received, the value is
'unknown(0)'. If P…
TmnxPtpTimeStampReferencePoint
Type Values:
0unknown
1port
2cpm
Description:
TmnxPtpTimeStampReferencePoint indicates the reference point where a
PTP event packet is timestamped in the SROS system:
unknown (0) - The reference point for the PTP timestamp has not yet
been deter…
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.17
The value of tmnxPtpPeerLastRxPortId along with
tmnxPtpPeerLastRxPortEncapType and tmnxPtpPeerLastRxPortEncapValue
indicates the last port used to receive PTP packets from the PTP peer.
If no packets have been received,…
TIMETRA-TC-MIBTmnxPortID
Description:
A portid is a unique 32 bit number with special encoding.

Refer to TIMETRA-CHASSIS-MIB::tmnxChassisPortIdScheme for a
description of the various port mapping schemes used by the system for
physical ports and …
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.18
The value of tmnxPtpPeerLastRxPortEncapType along with
tmnxPtpPeerLastRxPortId and tmnxPtpPeerLastRxPortEncapValue indicates
the last port used to receive PTP packets from the PTP peer.
TIMETRA-PORT-MIBTmnxPortEncapType
Type Values:
0unknown
1nullEncap
2qEncap
3mplsEncap
4bcpNullEncap
5bcpDot1qEncap
6ipcpEncap
7frEncap
8pppAutoEncap
9atmEncap
10qinqEncap
11wanMirrorEncap
12ciscoHDLCEncap
13cemEncap
14reserved14
15rawEncap
16cellularEncap
17wlanEncap
Description:
The type of encapsulation protocol configured on a port's network
interface.

When the encap type has a value of 'nullEncap',
frames received will not carry any tags
or labels and as a result only one service …
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.19
The value of tmnxPtpPeerLastRxPortEncapValue along with
tmnxPtpPeerLastRxPortId and tmnxPtpPeerLastRxPortEncapType indicates
the last port used to receive PTP packets from the PTP peer.
TIMETRA-TC-MIBTmnxEncapVal
Description:
The value of the label used to identify the entity using the specified
encapsulation value on a specific port.

The format of this object depends on the encapsulation type defined on
this port.

When…
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.20
The value of tmnxPtpPeerSyncInterval specifies the packet rate
requested in REQUEST_UNICAST_TRANSMISSION signaling messages for sync
packets when negotiating the sync unicast session with the peer clock.

…
TmnxPtpLogIntervalr/w
Constraints:
range: -6-0
Description:
TmnxPtpLogInterval specifies an interval between PTP packets, or
equivalently, a packet rate. It is specified as the logarithm to the
base 2 of the interval in seconds.

For example, -7 specifies a packet rat…
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.21
The non-empty value of tmnxPtpPeerAlternateProfile indicates an
existing alternate PTP profile tmnxPtpAltProfileName is applied to the
PTP peer.
TIMETRA-TC-MIBTLNamedItemOrEmpty
Based On: SNMPv2-TCDisplayString
Type Constraints:
range: 0..64
Description:
The long name of an item, or an empty string. When used in a reference
(TLNamedItemOrEmpty) the item name entry must exist in the table.

Note, use only NVT ASCII displayable characters here, no control
chara…
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.22
The value of tmnxPtpPeerMonitorReceiver specifies whether this
configured peer is enabled as a Monitor Receiver for PTP monitoring.

When configured to true and not in slave mode, the PTP peer will run
tim…
SNMPv2-TCTruthValuer/w
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.23
The value of tmnxPtpPeerNotMaster when set to true prevents this peer
from acting as a master when the profile is G.8275.1 or G.8275.2
SNMPv2-TCTruthValuer/w
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.2.3.1.24
.1.3.6.1.4.1.6527.3.1.2.74.2.4 · 1 row entry · 1 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpVRtrIfTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpVRtrIfTable'
The tmnxPtpVRtrIfTable table contains PTP configuration pertaining to
IP interfaces.
tmnxPtpVRtrIfEntry row .1.3.6.1.4.1.6527.3.1.2.74.2.4.1
Each row entry represents the PTP configuration corresponding to
an interface configured in a virtual router. Entries are created
and deleted when entries in the vRtrIfTable are created and deleted.
Indexes
No indexes recorded
Column Syntax OID
The value of tmnxPtpVRtrIfAdminState specifies the administrative
state of the PTP hardware assist configuration of the interface.

If the value is 'inService(2)', the timestamp point for PTP event
packets…
TIMETRA-TC-MIBTmnxAdminStater/w
Type Values:
1noop
2inService
3outOfService
Description:
The TmnxAdminState data type is an enumerated integer that describes
the values used to identify the administratively desired state of
functional modules.
.1.3.6.1.4.1.6527.3.1.2.74.2.4.1.1
.1.3.6.1.4.1.6527.3.1.2.74.2.5 · 1 row entry · 5 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpVRtrTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpVRtrTable'
The tmnxPtpVRtrTable consists of PTP configuration and status
information that is specific to a virtual router instance.
tmnxPtpVRtrEntry row .1.3.6.1.4.1.6527.3.1.2.74.2.5.1
A tmnxPtpVRtrEntry contains information pertaining to PTP on a
specific virtual router instance.

The system automatically creates one entry in this table that
corresponds to the base router instance. This …
Column Syntax OID
The value of tmnxPtpVRtrRowStatus controls the creation and deletion
of PTP on a virtual router instance.

Before removing PTP configuration from a virtual router instance,
tmnxPtpVRtrAdminState must be se…
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.6527.3.1.2.74.2.5.1.1
The value of tmnxPtpVRtrLastChanged indicates the time, since system
startup, that the configuration of PTP on the virtual router instance
was created or modified.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
.1.3.6.1.4.1.6527.3.1.2.74.2.5.1.2
The value of tmnxPtpVRtrAdminState specifies the administrative state
of PTP on the virtual router instance.

If tmnxPtpVRtrAdminState is 'outOfService (3)', no PTP packets will be
transmitted on that virt…
TIMETRA-TC-MIBTmnxAdminStater/w
Type Values:
1noop
2inService
3outOfService
Description:
The TmnxAdminState data type is an enumerated integer that describes
the values used to identify the administratively desired state of
functional modules.
.1.3.6.1.4.1.6527.3.1.2.74.2.5.1.3
The value of tmnxPtpVRtrOperState indicates the operational state of
PTP on the virtual router instance. The operational state will only be
'inService (2)' if PTP is administratively enabled on the virtual
router insta…
TIMETRA-TC-MIBTmnxOperState
Type Values:
1unknown
2inService
3outOfService
4transition
Description:
The TmnxOperState data type is an enumerated integer that describes
the values used to identify the current operational state of
functional modules.
.1.3.6.1.4.1.6527.3.1.2.74.2.5.1.4
The value of tmnxPtpVRtrPeerLimit specifies the maximum number of PTP
peers that may be automatically created by the system on this virtual
router instance.

The SROS system has a global limit on the numbe…
Integer32r/w
Constraints:
range: -1-512
.1.3.6.1.4.1.6527.3.1.2.74.2.5.1.5
.1.3.6.1.4.1.6527.3.1.2.74.2.6 · 1 row entry · 12 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpPortTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpPortTable'
The tmnxPtpPortTable consists of PTP configuration information that is
specific to Ethernet ports configured for direct transport of PTP over
Ethernet, as described in IEEE 1588-2008, Annex F.
tmnxPtpPortEntry row .1.3.6.1.4.1.6527.3.1.2.74.2.6.1
A tmnxPtpPortEntry contains configuration pertaining to PTP on a
specific Ethernet port.

Rows in this table may be created and destroyed by SNMP Set operations
on the object tmnxPtpPortRowStatus. Each row …
Column Syntax OID
The value of tmnxPtpPortRowStatus controls the creation and deletion
of PTP transport directly over Ethernet ports.

Before removing PTP configuration from an Ethernet port,
tmnxPtpPortAdminState must be s…
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.6527.3.1.2.74.2.6.1.1
The value of tmnxPtpPortLastChanged indicates the time, since system
startup, that the configuration of PTP transport on the Ethernet port
was created or modified.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
.1.3.6.1.4.1.6527.3.1.2.74.2.6.1.2
The value of tmnxPtpPortAdminState specifies the administrative state
of PTP on the Ethernet port.

If tmnxPtpPortAdminState is 'outOfService (3)', no PTP packets will be
directly transmitted on that Ether…
TIMETRA-TC-MIBTmnxAdminStater/w
Type Values:
1noop
2inService
3outOfService
Description:
The TmnxAdminState data type is an enumerated integer that describes
the values used to identify the administratively desired state of
functional modules.
.1.3.6.1.4.1.6527.3.1.2.74.2.6.1.3
The value of tmnxPtpPortSyncInterval specifies the mean interval
between successive multicast sync packets transmitted on this Ethernet
port when the corresponding PTP port is in the MASTER state.

The def…
TmnxPtpLogIntervalr/w
Constraints:
range: -6-0
Description:
TmnxPtpLogInterval specifies an interval between PTP packets, or
equivalently, a packet rate. It is specified as the logarithm to the
base 2 of the interval in seconds.

For example, -7 specifies a packet rat…
.1.3.6.1.4.1.6527.3.1.2.74.2.6.1.4
The value of tmnxPtpPortDelayInterval specifies the mean interval
initially sent between successive multicast delay packets transmitted
on this Ethernet port when the corresponding PTP port is in the SLAVE
state.
…
TmnxPtpLogIntervalr/w
Constraints:
range: -6-0
Description:
TmnxPtpLogInterval specifies an interval between PTP packets, or
equivalently, a packet rate. It is specified as the logarithm to the
base 2 of the interval in seconds.

For example, -7 specifies a packet rat…
.1.3.6.1.4.1.6527.3.1.2.74.2.6.1.5
The value of tmnxPtpPortMulticastAddress specifies the multicast MAC
address that the system will use to transport PTP messages directly
over Ethernet.

The value of tmnxPtpPortMulticastAddress may only be…
SNMPv2-TCMacAddressr/w
Type Constraints:
range: 6
Description:
Represents an 802 MAC address represented in the
`canonical' order defined by IEEE 802.1a, i.e., as if it
were transmitted least significant bit first, even though
802.5 (in contrast to other 802.x protocols) requires M…
.1.3.6.1.4.1.6527.3.1.2.74.2.6.1.6
The value of tmnxPtpPortLocalPriority specifies the local priority
used in the best master clock algorithm for the PTP port when
tmnxPtpClockProfile is 'g8275dot1-2014 (3)'.

This value is not applicable w…
TmnxPtpPriorityr/w
Constraints:
range: 1-255
Description:
The Precision Time Protocol (PTP) priority used both for the value to
advertise in the Announce messages and for the local clock value in
data set comparisons.

It is used by the Best Master Clock Algorithm to…
.1.3.6.1.4.1.6527.3.1.2.74.2.6.1.7
The value of tmnxPtpPortMasterOnly specifies whether the PTP clock can
synchronize using PTP timestamp information exchanged over this PTP
Ethernet port.

This value is only applicable when tmnxPtpClockPro…
SNMPv2-TCTruthValuer/w
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.2.6.1.8
The value of tmnxPtpPortAlternateProfile specifies an existing
alternate PTP profile tmnxPtpAltProfileName to be used for this PTP
port.

When tmnxPtpPortAlternateProfile is non-empty, this PTP port uses t…
TIMETRA-TC-MIBTLNamedItemOrEmptyr/w
Based On: SNMPv2-TCDisplayString
Type Constraints:
range: 0..64
Description:
The long name of an item, or an empty string. When used in a reference
(TLNamedItemOrEmpty) the item name entry must exist in the table.

Note, use only NVT ASCII displayable characters here, no control
chara…
.1.3.6.1.4.1.6527.3.1.2.74.2.6.1.9
The value of tmnxPtpPortMonitorSender specifies whether this PTP port
is enabled as a Monitor Sender for PTP monitoring.

When configured to true and not in master mode, the PTP port will send
Announce, Sy…
SNMPv2-TCTruthValuer/w
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.2.6.1.10
The value of tmnxPtpPortMonitorReceiver specifies whether this PTP
port is enabled as a Monitor Receiver for PTP monitoring.

When configured to true and not in slave mode, the PTP port will run
time recov…
SNMPv2-TCTruthValuer/w
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.2.6.1.11
The value of tmnxPtpPortNotMaster when set to true prevents this port
from acting as a master when the profile is G.8275.1 or G.8275.2
SNMPv2-TCTruthValuer/w
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.2.6.1.12
.1.3.6.1.4.1.6527.3.1.2.74.2.7 · 1 row entry · 7 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpAltProfileTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpAltProfileTable'
The table tmnxPtpAltProfileTable contains information for
alternate PTP profiles.  The system may distribute timing to
other PTP clocks via an alternate PTP profile than the main
PTP profile that it uses to recover timing information.
tmnxPtpAltProfileEntry row .1.3.6.1.4.1.6527.3.1.2.74.2.7.1
tmnxPtpAltProfileEntry contains information pertaining to an alternate
PTP profile.

Rows in table tmnxPtpAltProfileTable are created and destroyed by SNMP
set operations on the object tmnxPtpAltProfileRowSt…
Column Syntax OID
The value of tmnxPtpAltProfileName specifies the unique name given to
this alternate PTP profile.
TIMETRA-TC-MIBTLNamedItem
Based On: SNMPv2-TCDisplayString
Type Constraints:
range: 1..64
Description:
The long name of an item. When used as an index to a table, the item
name uniquely identifies the instance. When used in a reference
(TLNamedItemOrEmpty) the item name entry must exist in the table.

Note, u…
.1.3.6.1.4.1.6527.3.1.2.74.2.7.1.1
The value of tmnxPtpAltProfileLastChanged indicates the time, since
system startup, this row in tmnxPtpAltProfileTable was created or
modified.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
.1.3.6.1.4.1.6527.3.1.2.74.2.7.1.2
The value of tmnxPtpAltProfileRowStatus specifies the row status, and
it is used to control the creation and deletion of an alternate PTP
profile.

To delete an alternate PTP profile, tmnxPtpAltProfileAdmi…
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.6527.3.1.2.74.2.7.1.3
The value of tmnxPtpAltProfileAdminState specifies the administrative
state of this alternate PTP profile.

When the value of tmnxPtpAltProfileAdminState is 'disabled (2)', the
system will set the value tm…
TIMETRA-TC-MIBTmnxEnabledDisabledAdminStater/w
Type Values:
1enabled
2disabled
Description:
The TmnxEnabledDisabledAdminState data type is an enumerated integer
that describes the values used to identify whether an entity is
'enabled' or 'disabled'. It is to be used for admin state leafs.
.1.3.6.1.4.1.6527.3.1.2.74.2.7.1.4
The value of tmnxPtpAltProfileProfile specifies the conformance of the
PTP profile in the ITU-T specification.

This object can only be modified if tmnxPtpAltProfileAdminState is set
to 'disabled (2)'.
TmnxPtpProfiler/w
Type Values:
1g8265dot1-2010
2ieee1588-2008
3g8275dot1-2014
4g8275dot2-2016
5iec-61850-9-3-2016
6c37dot238-2017
Description:
The Precision Time Protocol (PTP) profile specifies the standard to
which PTP conforms.
g8265dot1-2010 - conforms to the PTP profile specified in the
ITU-T G.8265.1 specification
…
.1.3.6.1.4.1.6527.3.1.2.74.2.7.1.5
The value of tmnxPtpAltProfileDomain specifies the configured clock
domain value for this alternate PTP profile.

This object can only be modified if tmnxPtpAltProfileAdminState is set
to 'disabled (2)'.
TmnxPtpDomainr/w
Type Constraints:
range: 0..255
Description:
TmnxPtpDomain specifies the Precision Time Protocol (PTP) domain.

The value 0 specifies the default domain for IEEE1588-2008
specification. The value 4 specifies the default domain for ITU-T
G.8265.1 specific…
.1.3.6.1.4.1.6527.3.1.2.74.2.7.1.6
The value of tmnxPtpAltProfileLogAnnoInterval specifies the interval
between Announce packets transmitted on PTP ports using this alternate
PTP profile.

This object can only be modified if tmnxPtpAltProfi…
TmnxPtpLogIntervalr/w
Constraints:
range: -3-4
Description:
TmnxPtpLogInterval specifies an interval between PTP packets, or
equivalently, a packet rate. It is specified as the logarithm to the
base 2 of the interval in seconds.

For example, -7 specifies a packet rat…
.1.3.6.1.4.1.6527.3.1.2.74.2.7.1.7
.1.3.6.1.4.1.6527.3.1.2.74.2.8 · 1 row entry · 6 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpPbtPortFilterTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpPbtPortFilterTable'
The table tmnxPtpPbtPortFilterTable contains configuration pertaining
to filtering for the ingress timestamping of Precision Timing Protocol
(PTP) messages for multiple interfaces on a given Ethernet port or a
Link Aggregation Group (LAG).
tmnxPtpPbtPortFilterEntry row .1.3.6.1.4.1.6527.3.1.2.74.2.8.1
Each row contains configuration defining a filter for the ingress
timestamping of Precision Timing Protocol (PTP) messages for multiple
interfaces on a given Ethernet port or a Link Aggregation Group (LAG).
Rows in tabl…
Column Syntax OID
tmnxPtpPbtPortFilterPortID is an index into this table.
TIMETRA-TC-MIBTmnxPortID
Description:
A portid is a unique 32 bit number with special encoding.

Refer to TIMETRA-CHASSIS-MIB::tmnxChassisPortIdScheme for a
description of the various port mapping schemes used by the system for
physical ports and …
.1.3.6.1.4.1.6527.3.1.2.74.2.8.1.1
RowStatus for this entry.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.6527.3.1.2.74.2.8.1.2
The value of tmnxPtpPbtPortFilterLastChanged indicates the time, since
system startup, this row in tmnxPtpPbtPortFilterTable was created or
modified..
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
.1.3.6.1.4.1.6527.3.1.2.74.2.8.1.3
The value of tmnxPtpPbtPortFilterAdminState specifies the
administrative state of ptp-timestamping.
TIMETRA-TC-MIBTmnxEnabledDisabledr/w
Type Values:
1enabled
2disabled
Description:
The TmnxEnabledDisabled data type is an enumerated integer that
describes the values used to identify whether an entity is 'enabled'
or 'disabled'.
.1.3.6.1.4.1.6527.3.1.2.74.2.8.1.4
The value of tmnxPtpPbtPortFilterIpv4Addr specifies the IPv4
destination address for PTP messages into this port. A value of all
zeros indicates that no IPv4 address was configured
INET-ADDRESS-MIBInetAddressIPv4r/w
Type Constraints:
range: 4
.1.3.6.1.4.1.6527.3.1.2.74.2.8.1.5
The value of tmnxPtpPbtPortFilterIpv6Addr specifies the IPv6
destination address for PTP messages into this port. A value of all
zeros indicates that no IPv6 address was configured
INET-ADDRESS-MIBInetAddressIPv6r/w
Type Constraints:
range: 16
.1.3.6.1.4.1.6527.3.1.2.74.2.8.1.6
.1.3.6.1.4.1.6527.3.1.2.74.3.1 · 1 row entry · 14 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpClockOperTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpClockOperTable'
The tmnxPtpClockOperTable contains the operational information for the
individual Precision Timing Protocol (PTP) for each CPM card in the
SROS system.
tmnxPtpClockOperEntry row .1.3.6.1.4.1.6527.3.1.2.74.3.1.1
The tmnxPtpClockOperEntry consists of the operational information for
the PTP clock on an individual CPM card.
Indexes
No indexes recorded
Column Syntax OID
The value of tmnxPtpClockIdentity indicates the identify of the local
Clock. This object corresponds to the value of the
defaultDS.clockIdentity data set member defined by IEEE Std 1588-2008.

The clock i…
TmnxPtpClockIdentity
Type Constraints:
range: 8
Description:
TmnxPtpClockIdentity specifies the unique identifier used to identify
a network element participating in the Precision Time Protocol (PTP).
.1.3.6.1.4.1.6527.3.1.2.74.3.1.1.1
The value of tmnxPtpClockOperState indicates the operational state of
PTP 1588 on the system.

On some SROS systems, PTP may remain operationally out of service
even when PTP is administratively in service…
TIMETRA-TC-MIBTmnxOperState
Type Values:
1unknown
2inService
3outOfService
4transition
Description:
The TmnxOperState data type is an enumerated integer that describes
the values used to identify the current operational state of
functional modules.
.1.3.6.1.4.1.6527.3.1.2.74.3.1.1.2
The value of tmnxPtpClockStepType indicates how the system provides
timing information. SROS systems always have a tmnxPtpClockStepType of
'oneStep (1)', and never transmit PTP 'follow up' packets.
TmnxPtpClockStepType
Type Values:
0unknown
1oneStep
2twoStep
Description:
TmnxPtpClockStepType specifies the clock step:
unknown (0) - It is unknown whether the clock is a one-step or
two-step clock. No announce messages have been
received from the remote clock.
o…
.1.3.6.1.4.1.6527.3.1.2.74.3.1.1.3
The value of tmnxPtpClockClass indicates the local clock class. The
value of this object corresponds to the defaultDS.clockQuality data
set member defined in IEEE Std 1588-2008.

When tmnxPtpClockClockType…
TmnxPtpClockClass
Type Constraints:
range: 0..255
Description:
TmnxPtpClockClass specifies the traceability of the time or frequency
distributed by the grandmaster clock.
.1.3.6.1.4.1.6527.3.1.2.74.3.1.1.4
The value of tmnxPtpClockAccuracy indicates the accuracy of the clock.
The value of this object corresponds to the
defaultDS.clockQuality.clockAccuracy data set member defined in IEEE
Std 1588-2008. For SROS systems, th…
TmnxPtpClockAccuracy
Type Constraints:
range: 0..255
Description:
TmnxPtpClockAccuracy specifies the mean of the time frequency error
between the clock under test and a perfect reference clock, over an
ensemble of measurements.
.1.3.6.1.4.1.6527.3.1.2.74.3.1.1.5
The value of tmnxPtpClockVariance indicates the inherent precision of
the local clock. The value of this object corresponds to the
defaultDS.clockQuality.clockVariance data set member defined in IEEE
Std 1588-2008.
TmnxPtpClockVariance
Type Constraints:
range: 0..65535
Description:
TmnxPtpClockVariance is a measure of the precision of a clock. The
value 65535 indicates that the variance is either too large to be
represented or has not been computed.
.1.3.6.1.4.1.6527.3.1.2.74.3.1.1.6
The value of tmnxPtpClockPortState indicates the current state of the
single PTP port when tmnxPtpClockClockType is either
'ordinarySlave (1)' or 'ordinaryMaster (2)'. Otherwise,
tmnxPtpClockPortState is 'notApplicable…
TmnxPtpPortState
Type Values:
0notApplicable
1initializing
2faulty
3disabled
4listening
5preMaster
6master
7passive
8uncalibrated
9slave
Description:
TmnxPtpPortState indicates the operational state of a PTP port.
.1.3.6.1.4.1.6527.3.1.2.74.3.1.1.7
The value of tmnxPtpClockPortStateLastChanged indicates the time,
since system startup, when the tmnxPtpClockPortState last changed
state.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
.1.3.6.1.4.1.6527.3.1.2.74.3.1.1.8
The value of tmnxPtpClockRecoveryState indicates the state of the clock
recovery process on a PTP system. The various states are:
notApplicable (0) - The system is not attempting to recover a clock
initial …
Enumeration
Enumerated Values:
0notApplicable
1initial
2acquiring
3phaseTracking
4holdover
5locked
.1.3.6.1.4.1.6527.3.1.2.74.3.1.1.9
The value of tmnxPtpClockRecoveryStateLastChg indicates the time,
since system startup, when tmnxPtpClockRecoveryState last changed
state.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
.1.3.6.1.4.1.6527.3.1.2.74.3.1.1.10
The value of tmnxPtpClockFrequencyOffset indicates the frequency offset
of the recovered clock, from the nominal clock rate, in parts per
trillion. Positive values indicate that the recovered clock is faster
than nomin…
parts per trillionSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.3.1.1.11
The value of tmnxPtpTimeRecoveryState indicates the state of the time
recovery process to the parent clock on a PTP system.
The various states are:
disabled (0) - The system is not attempting to recover time.
…
Enumeration
Enumerated Values:
0disabled
1initial
2acquiring
3locked
4holdover
.1.3.6.1.4.1.6527.3.1.2.74.3.1.1.12
The value of tmnxPtpTimeRecoveryStateLastChg indicates the time, since
system startup, when tmnxPtpTimeRecoveryState last changed state.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
.1.3.6.1.4.1.6527.3.1.2.74.3.1.1.13
The value of tmnxPtpClockStepsRemoved indicates the number of hops
separating the PTP clock from the grandmaster clock.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.3.1.1.14
.1.3.6.1.4.1.6527.3.1.2.74.3.3 · 1 row entry · 17 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpPeerMasterStatusTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpPeerMasterStatusTable'
The tmnxPtpPeerMasterStatusTable consists of Precision Time Protocol
Master Peer state information. This table extends the
tmnxPtpPeerConfigTable for peers configured as grandmaster or boundary
PTP clocks that may provide timing information to the local clock.
tmnxPtpPeerMasterStatusEntry row .1.3.6.1.4.1.6527.3.1.2.74.3.3.1
The tmnxPtpPeerMasterStatusEntry contains the information pertaining
to Precision Time Protocol peers configured as master clocks.

Rows in this table are created and destroyed by the system based on
the con…
Column Syntax OID
The value of tmnxPtpPeerMasterCurrentMaster indicates whether or not
this PTP Peer has been chosen by the PTP Best Master Clock Algorithm
as the current parent clock.
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.3.3.1.1
The value of tmnxPtpPeerMasterClockStepType indicates the step type of
the PTP peer.
TmnxPtpClockStepType
Type Values:
0unknown
1oneStep
2twoStep
Description:
TmnxPtpClockStepType specifies the clock step:
unknown (0) - It is unknown whether the clock is a one-step or
two-step clock. No announce messages have been
received from the remote clock.
o…
.1.3.6.1.4.1.6527.3.1.2.74.3.3.1.2
The value of tmnxPtpPeerMasterClockStepsRemvd indicates the number of
steps the master is removed from the grandmaster clock. This value is
taken from the last announce packet received from the peer clock.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.3.3.1.3
The value of tmnxPtpPeerMasterGMClockId indicates the identity of the
grandmaster PTP clock. This value is taken from the last Announce
packet received from the peer clock.
TmnxPtpClockIdentity
Type Constraints:
range: 8
Description:
TmnxPtpClockIdentity specifies the unique identifier used to identify
a network element participating in the Precision Time Protocol (PTP).
.1.3.6.1.4.1.6527.3.1.2.74.3.3.1.4
The value of tmnxPtpPeerMasterGMClockPrio1 indicates the 'priority1'
value of the grandmaster clock. This value is taken from the last
announce packet received from the peer clock.
TmnxPtpPriority
Type Constraints:
range: 0..255
Description:
The Precision Time Protocol (PTP) priority used both for the value to
advertise in the Announce messages and for the local clock value in
data set comparisons.

It is used by the Best Master Clock Algorithm to…
.1.3.6.1.4.1.6527.3.1.2.74.3.3.1.5
The value of tmnxPtpPeerMasterGMClockPrio2 indicates the 'priority2'
value of the grandmaster clock. This value is taken from the last
announce packet received from the peer clock.
TmnxPtpPriority
Type Constraints:
range: 0..255
Description:
The Precision Time Protocol (PTP) priority used both for the value to
advertise in the Announce messages and for the local clock value in
data set comparisons.

It is used by the Best Master Clock Algorithm to…
.1.3.6.1.4.1.6527.3.1.2.74.3.3.1.6
The value of tmnxPtpPeerMasterGMClockClass indicates the clock class
of the grandmaster clock. This value is taken from the last announce
packet received from the peer clock.
TmnxPtpClockClass
Type Constraints:
range: 0..255
Description:
TmnxPtpClockClass specifies the traceability of the time or frequency
distributed by the grandmaster clock.
.1.3.6.1.4.1.6527.3.1.2.74.3.3.1.7
The value of tmnxPtpPeerMasterGMClockAccuracy indicates the clock
accuracy of the grandmaster clock. This value is taken from the last
announce packet received from the peer clock.
TmnxPtpClockAccuracy
Type Constraints:
range: 0..255
Description:
TmnxPtpClockAccuracy specifies the mean of the time frequency error
between the clock under test and a perfect reference clock, over an
ensemble of measurements.
.1.3.6.1.4.1.6527.3.1.2.74.3.3.1.8
The value of tmnxPtpPeerMasterGMClockVariance indicates the clock
variance of the grandmaster clock. This value is taken from the last
announce packet received from the peer clock.
TmnxPtpClockVariance
Type Constraints:
range: 0..65535
Description:
TmnxPtpClockVariance is a measure of the precision of a clock. The
value 65535 indicates that the variance is either too large to be
represented or has not been computed.
.1.3.6.1.4.1.6527.3.1.2.74.3.3.1.9
The value of tmnxPtpPeerMasterAlarm indicates the alarm status of the
PTP peer clock:

ptsfLossAnnounce(0)
The peer is in the 'Packet Timing Signal Fail (Loss Announce)'
state, indicating …
Bits
Enumerated Values:
0ptsfLossAnnounce
1ptsfLossSync
.1.3.6.1.4.1.6527.3.1.2.74.3.3.1.11
The value of tmnxPtpPeerMasterBestMaster indicates whether or not this
PTP Peer is the best master clock, as decided by the Best Master Clock
Algorithm (BMCA).

Even if tmnxPtpPeerMasterBestMaster is true,…
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.3.3.1.12
The value of tmnxPtpPeerMasterDelayAsymmetry indicates the estimated
delay asymmetry in the path between the master clock and the local
clock.

This leaf was obsoleted in Release 24.3 and was replaced by
t…
TmnxPtpDelayAsymmetry
Based On: TmnxPtpTimeInterval
Description:
TmnxPtpDelayAsymmetry indicates the estimated delay asymmetry of the PTP
path between two PTP clocks. The local clock estimates the delay asymmetry
of the path by comparing against another source of time synchronizatio…
.1.3.6.1.4.1.6527.3.1.2.74.3.3.1.13
The value of tmnxPtpPeerMasterDelayAsymCalc indicates the time, since
system startup, when tmnxPtpPeerMasterDelayAsymmetry was last
calculated.

A value of 0 indicates that the local clock has not estimate…
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
.1.3.6.1.4.1.6527.3.1.2.74.3.3.1.14
The value of tmnxPtpPeerMasterBackup indicates whether this peer is
the backup when the clock is using GNSS
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.3.3.1.15
The value of tmnxPtpPeerOffsetFrLocal indicates the time offset
between the clock recovered from the peer and the local clock's time.
This time offset may be caused by delay asymmetry in the path between
the peer's cloc…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.3.3.1.16
The value of tmnxPtpPeerOffsetFrLocalCalc indicates the time, since
system startup, when tmnxPtpPeerOffsetFrLocalNs was last calculated.

A value of 0 indicates that the local clock has not estimated the
d…
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
.1.3.6.1.4.1.6527.3.1.2.74.3.3.1.17
The value of tmnxPtpPeerOffsetFrLocalNs indicates the time offset
between the clock recovered from the peer and the local clock's time.
This time offset may be caused by delay asymmetry in the path between
the peer's cl…
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.3.3.1.18
.1.3.6.1.4.1.6527.3.1.2.74.3.4 · 1 row entry · 6 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpPeerUnicastTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpPeerUnicastTable'
The tmnxPtpPeerUnicastTable consists of the status of unicast
messaging service between the local PTP clock and all other PTP
clocks.
tmnxPtpPeerUnicastEntry row .1.3.6.1.4.1.6527.3.1.2.74.3.4.1
The tmnxPtpPeerUnicastEntry contains the status of unicast messaging
service between PTP clocks for the specified packet type in the
direction specified.

Rows in this table are created and destroyed by the …
Column Syntax OID
The value of tmnxPtpPeerUnicastDirection specifies the direction
of packet flow for tmnxPtpPeerUnicastPktType packets (announce,
sync, or delay response). Ordinary slave clocks will only have
entries in tmnxPtpPeerUni…
TmnxPtpDirection
Type Values:
1rx
2tx
Description:
TmnxPtpDirection specifies which direction packets are travelling in
the system:
rx - Packets are being received by the system.
tx - Packets are being transmitted from the system.
.1.3.6.1.4.1.6527.3.1.2.74.3.4.1.1
The value of tmnxPtpPeerUnicastPktType specifies the packet type
described by the values in this table entry.
Enumeration
Enumerated Values:
1announce
2sync
3delayResponse
.1.3.6.1.4.1.6527.3.1.2.74.3.4.1.2
The value of tmnxPtpPeerUnicastStatus indicates:
pending (1) - a request for unicast transmission has been sent to
the master, but no reply has been received.
granted (2) - the packet rate and duration …
Enumeration
Enumerated Values:
1pending
2granted
3denied
4expired
5canceled
.1.3.6.1.4.1.6527.3.1.2.74.3.4.1.3
The value of tmnxPtpPeerUnicastRate indicates the packet rate
requested or granted for unicast transmission between the PTP peers.
TmnxPtpLogInterval
Type Constraints:
range: -128..127
Description:
TmnxPtpLogInterval specifies an interval between PTP packets, or
equivalently, a packet rate. It is specified as the logarithm to the
base 2 of the interval in seconds.

For example, -7 specifies a packet rat…
.1.3.6.1.4.1.6527.3.1.2.74.3.4.1.4
The value of tmnxPtpPeerUnicastDuration indicates the duration, in
seconds, requested or granted for unicast transmission between the PTP
peers.
secondsSNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.3.4.1.5
The value of tmnxPtpPeerUnicastEventTime indicates the time, since
system startup, that tmnxPtpPeerUnicastStatus last changed or the
unicast session between the PTP clocks was renewed.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
.1.3.6.1.4.1.6527.3.1.2.74.3.4.1.6
.1.3.6.1.4.1.6527.3.1.2.74.3.6 · 1 row entry · 10 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpPortStatusTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpPortStatusTable'
The tmnxPtpPortStatusTable consists of PTP status information that is
specific to Ethernet ports configured for direct transport of PTP over
Ethernet, as described in IEEE 1588-2008, Annex F.
tmnxPtpPortStatusEntry row .1.3.6.1.4.1.6527.3.1.2.74.3.6.1
A tmnxPtpPortStatusEntry contains status information pertaining to PTP
on a specific Ethernet port. Entries are created and deleted
when entries in the tmnxPtpPortTable are created and deleted.
Indexes
No indexes recorded
Column Syntax OID
The value of tmnxPtpPortLocalPortNumber indicates the PTP port number
assigned by the local clock and used when communicating directly over
the Ethernet physical port corresponding to this table row.

If t…
TmnxPtpPortNumber
Type Constraints:
range: 0..65534
Description:
TmnxPtpPortNumber specifies a number which identifies a logical access
point of a clock for PTP communications to the communications network.

A PTP ordinary clock has exactly one PTP port, with port number 1.…
.1.3.6.1.4.1.6527.3.1.2.74.3.6.1.1
The value of tmnxPtpPortOperState indicates the operational state of
PTP on the Ethernet port.

The operational state will only be 'inService (2)' if PTP is
administratively enabled on the port, if PTP is …
TIMETRA-TC-MIBTmnxOperState
Type Values:
1unknown
2inService
3outOfService
4transition
Description:
The TmnxOperState data type is an enumerated integer that describes
the values used to identify the current operational state of
functional modules.
.1.3.6.1.4.1.6527.3.1.2.74.3.6.1.2
The value of tmnxPtpPortState indicates the current state of the PTP
port.

The value of this object corresponds to the portDS.portState data set
member defined in IEEE Std 1588-2008.
TmnxPtpPortState
Type Values:
0notApplicable
1initializing
2faulty
3disabled
4listening
5preMaster
6master
7passive
8uncalibrated
9slave
Description:
TmnxPtpPortState indicates the operational state of a PTP port.
.1.3.6.1.4.1.6527.3.1.2.74.3.6.1.3
The value of tmnxPtpPortTimeStampRefPoint indicates the reference point
used to generate PTP timestamps for transmitted and received PTP event
packets on the port. If the port is capable of timestamping PTP
packets at …
TmnxPtpTimeStampReferencePoint
Type Values:
0unknown
1port
2cpm
Description:
TmnxPtpTimeStampReferencePoint indicates the reference point where a
PTP event packet is timestamped in the SROS system:
unknown (0) - The reference point for the PTP timestamp has not yet
been deter…
.1.3.6.1.4.1.6527.3.1.2.74.3.6.1.4
The value of tmnxPtpPortNeighbors indicates the numbers of neighboring
PTP clocks visible to the local clock on the Ethernet port.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.3.6.1.5
The value of tmnxPtpPortTxPacketRate indicates the current rate of PTP
packets that the local PTP clock is transmitting on the Ethernet port.

This packet rate includes all PTP packets transmitted by the l…
packets per secondSNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.3.6.1.6
The value of tmnxPtpPortRxPacketRate indicates the current rate of PTP
packets received by the local PTP clock on the Ethernet port.

This packet rate includes all PTP packets received on the port. These
…
packets per secondSNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.3.6.1.7
The value of tmnxPtpPortSrcMacAddr is the MAC address of the PTP port
that is used as source MAC address of the Ethernet frames carrying
L2-PTP messages, transmitted through associated physical port.

This…
SNMPv2-TCMacAddress
Type Constraints:
range: 6
Description:
Represents an 802 MAC address represented in the
`canonical' order defined by IEEE 802.1a, i.e., as if it
were transmitted least significant bit first, even though
802.5 (in contrast to other 802.x protocols) requires M…
.1.3.6.1.4.1.6527.3.1.2.74.3.6.1.8
The value of tmnxPtpPortMeanLinkDelayNs contains the estimated one-way
propagation delay on the PTP link, computed using the peer-to-peer
delay mechanism.

It represents the 'instantaneous' value of the ca…
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.3.6.1.9
The value of tmnxPtpPortMeanLinkDelayLastCalc indicates the time,
since system startup, when tmnxPtpPortMeanLinkDelayNs was last
calculated.

If the clock has not calculated the mean link delay,
tmnxPtpPor…
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
.1.3.6.1.4.1.6527.3.1.2.74.3.6.1.10
.1.3.6.1.4.1.6527.3.1.2.74.3.7 · 1 row entry · 20 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpPortNeighborTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpPortNeighborTable'
The tmnxPtpPortNeighborTable contains information on the neighbor PTP
clocks communicating using direct transport of PTP over Ethernet and
visible to the local PTP clock.
          
Table entries are created automatically by the system upon reception of
PTP Ethernet multicast packets from neighboring PTP clocks.  Individual
table entries are deleted automatically by the system if no PTP packets
are received from the neighbor clock for a period of time.
tmnxPtpPortNeighborEntry row .1.3.6.1.4.1.6527.3.1.2.74.3.7.1
A tmnxPtpPortNeighborEntry contains information about an individual
PTP clock visible to the local PTP clock.
Column Syntax OID
The value of tmnxPtpPortNeighborMacAddress indicates the MAC address
of the neighboring PTP clock.
SNMPv2-TCMacAddress
Type Constraints:
range: 6
Description:
Represents an 802 MAC address represented in the
`canonical' order defined by IEEE 802.1a, i.e., as if it
were transmitted least significant bit first, even though
802.5 (in contrast to other 802.x protocols) requires M…
.1.3.6.1.4.1.6527.3.1.2.74.3.7.1.1
The value of tmnxPtpPortNeighborClockId indicates the PTP clock
identity of the neighboring PTP clock.
TmnxPtpClockIdentity
Type Constraints:
range: 8
Description:
TmnxPtpClockIdentity specifies the unique identifier used to identify
a network element participating in the Precision Time Protocol (PTP).
.1.3.6.1.4.1.6527.3.1.2.74.3.7.1.2
The value of tmnxPtpPortNeighborPtpPortNumber indicates the PTP port
number of the PTP port on the neighbor clock that is connected to the
local clock on this Ethernet port.
TmnxPtpPortNumber
Type Constraints:
range: 0..65534
Description:
TmnxPtpPortNumber specifies a number which identifies a logical access
point of a clock for PTP communications to the communications network.

A PTP ordinary clock has exactly one PTP port, with port number 1.…
.1.3.6.1.4.1.6527.3.1.2.74.3.7.1.3
The value of tmnxPtpPortNeighborRxPacketRate indicates the current
rate of PTP packets received by the local clock from the neighboring
PTP clock.
packets per secondSNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.3.7.1.4
The value of tmnxPtpPortNeighborPtsfUnusable indicates whether or not
the neighboring PTP clock has Packet Timing Signal Fail (PTSF)
unusable set.
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.3.7.1.5
The value of tmnxPtpNeighborBestMaster indicates whether or not this
neighboring clock is the best master clock, as decided by the Best
Master Clock Algorithm (BMCA).

Even if tmnxPtpNeighborBestMaster is …
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.3.7.1.6
The value of tmnxPtpNeighborParentClock indicates whether or not this
neighboring clock is the parent clock, as decided by the Best Master
Clock Algorithm (BMCA).
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.3.7.1.7
The value of tmnxPtpNeighborDelayAsymmetry indicates the estimated
delay asymmetry in the path between the neighboring clock and the
local clock.

This leaf was obsoleted in Release 24.3 and was replaced b…
TmnxPtpDelayAsymmetry
Based On: TmnxPtpTimeInterval
Description:
TmnxPtpDelayAsymmetry indicates the estimated delay asymmetry of the PTP
path between two PTP clocks. The local clock estimates the delay asymmetry
of the path by comparing against another source of time synchronizatio…
.1.3.6.1.4.1.6527.3.1.2.74.3.7.1.8
The value of tmnxPtpNeighborDelayAsymCalc indicates the time, since
system startup, when tmnxPtpNeighborDelayAsymmetry was last
calculated.

A value of 0 indicates that the local clock has not estimated th…
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
.1.3.6.1.4.1.6527.3.1.2.74.3.7.1.9
The value of tmnxPtpNeighborBackup indicates whether this port is the
backup when the clock is using GNSS
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.3.7.1.10
The value of tmnxPtpNeighborOffsetFrLocal indicates the time offset
between the clock recovered from the neighboring clock and the local
clock's time. This time offset may be caused by delay asymmetry in the
path betwee…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.3.7.1.11
The value of tmnxPtpNeighborOffsetFrLocalCalc indicates the time,
since system startup, when tmnxPtpNeighborOffsetFrLocalNs was last
calculated.

A value of 0 indicates that the local clock has not estimat…
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
.1.3.6.1.4.1.6527.3.1.2.74.3.7.1.12
The value of tmnxPtpNeighborMonTimeRecovState indicates the state of
the time recovery to a master clock on a PTP system.

The various states are:
disabled (0) - The process is not attempting to recov…
Enumeration
Enumerated Values:
0disabled
1initial
2acquiring
3locked
4holdover
.1.3.6.1.4.1.6527.3.1.2.74.3.7.1.13
The value of tmnxPtpNeighbMonTimeRecStLastChg indicates the time,
since system startup, when the time recovery state object last changed
state.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
.1.3.6.1.4.1.6527.3.1.2.74.3.7.1.14
The value of tmnxPtpNeighbMonTimeOffFrMaster indicates the current
offset of the local PTP clock from a master PTP clock, calculated by
the local clock, as per IEEE Std 1588-2008, section 11.2 when Monitor
Receiver has …
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.3.7.1.15
The value of tmnxPtpNeighbMonTimeMeanPathDlay indicates the current
value of the mean propagation time between the local PTP clock and a
master PTP clock, calculated by the local clock, as per IEEE Std
1588-2008, sectio…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.3.7.1.16
The value of tmnxPtpNeighborMonTimeLastCalc indicates the time, since
system startup, when tmnxPtpNeighbMonTimeOffFrMastNs and
tmnxPtpNeighbMonTimeMnPathDlyNs were last calculated.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
.1.3.6.1.4.1.6527.3.1.2.74.3.7.1.17
The value of tmnxPtpNeighborOffsetFrLocalNs indicates the time offset
between the clock recovered from the neighboring clock and the local
clock's time. This time offset may be caused by delay asymmetry in the
path betw…
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.3.7.1.18
The value of tmnxPtpNeighbMonTimeOffFrMastNs indicates the current
offset of the local PTP clock from a master PTP clock, calculated by
the local clock, as per IEEE Std 1588-2008, section 11.2 when Monitor
Receiver has …
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.3.7.1.19
The value of tmnxPtpNeighbMonTimeMnPathDlyNs indicates the current
value of the mean propagation time between the local PTP clock and a
master PTP clock, calculated by the local clock, as per IEEE Std
1588-2008, section…
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.3.7.1.20
.1.3.6.1.4.1.6527.3.1.2.74.3.8 · 1 row entry · 2 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpGnssPortStatusTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpGnssPortStatusTable'
The tmnxPtpGnssPortStatusTable consists of PTP status information that
is specific to GNSS ports.
          
This table contains an entry for each GNSS port in the system when
tmnxPtpClockClockType is 'boundary (3)'.  When tmnxPtpClockClockType is 'ordinarySlave (1)'
or 'ordinaryMaster (2)', this table does not contains any entries.
tmnxPtpGnssPortStatusEntry row .1.3.6.1.4.1.6527.3.1.2.74.3.8.1
A tmnxPtpGnssPortStatusEntry contains status information pertaining to
PTP on a specific GNSS port.
Column Syntax OID
The value of tmnxPtpPortLocalGnssPortNumber indicates the PTP port
number assigned by the local clock.

The value of this object corresponds to the
portDS.portIdentity.portNumber data set member defined in…
TmnxPtpPortNumber
Type Constraints:
range: 0..65534
Description:
TmnxPtpPortNumber specifies a number which identifies a logical access
point of a clock for PTP communications to the communications network.

A PTP ordinary clock has exactly one PTP port, with port number 1.…
.1.3.6.1.4.1.6527.3.1.2.74.3.8.1.1
The value of tmnxPtpGnssPortState indicates the current state of the
PTP port.

The value of this object corresponds to the portDS.portState data set
member defined in IEEE Std 1588-2008.
TmnxPtpPortState
Type Values:
0notApplicable
1initializing
2faulty
3disabled
4listening
5preMaster
6master
7passive
8uncalibrated
9slave
Description:
TmnxPtpPortState indicates the operational state of a PTP port.
.1.3.6.1.4.1.6527.3.1.2.74.3.8.1.2
.1.3.6.1.4.1.6527.3.1.2.74.3.9 · 1 row entry · 1 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpTimestampingTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpTimestampingTable'
The table tmnxPtpTimestampingTable contains status information that is
specific to PTP timestamping
tmnxPtpTimestampingEntry row .1.3.6.1.4.1.6527.3.1.2.74.3.9.1
A tmnxPtpTimestampingEntry contains status information pertaining to
PTP timestamping on a specific port.
Indexes
No indexes recorded
Column Syntax OID
The value of tmnxPtpPortTSCapabilities indicates the capability of
the Ethernet port to support port-based-timestamping when the Ethernet
port transports PTP packets using the given encapsulation.
ethernet - PTP in …
Bits
Enumerated Values:
0ethernet
1ipv4
2ipv6
.1.3.6.1.4.1.6527.3.1.2.74.3.9.1.1
.1.3.6.1.4.1.6527.3.1.2.74.3.10 · 1 row entry · 7 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpPeerStatusTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpPeerStatusTable'
The table tmnxPtpPeerStatusTable contains status information that is
specific to the Precision Time Protocol (PTP) peers
tmnxPtpPeerStatusEntry row .1.3.6.1.4.1.6527.3.1.2.74.3.10.1
The tmnxPtpPeerStatusEntry contains status information pertaining to
an individual peer for the Precision Time Protocol (PTP).
Column Syntax OID
The value of tmnxPtpPeerMonTimeRecoveryState indicates the state of
the time recovery to a master clock on a PTP system.

The various states are:
disabled (0) - The process is not attempting to recove…
Enumeration
Enumerated Values:
0disabled
1initial
2acquiring
3locked
4holdover
.1.3.6.1.4.1.6527.3.1.2.74.3.10.1.1
The value of tmnxPtpPeerMonTimeRecStateLstChg indicates the time,
since system startup, when the time recovery state object last changed
state.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
.1.3.6.1.4.1.6527.3.1.2.74.3.10.1.2
The value of tmnxPtpPeerMonTimeOffsetFrMaster indicates the current
offset of the local PTP clock from a master PTP clock, calculated by
the local clock, as per IEEE Std 1588-2008, section 11.2 when Monitor
Receiver has…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.3.10.1.3
The value of tmnxPtpPeerMonTimeMeanPathDelay indicates the current
value of the mean propagation time between the local PTP clock and a
master PTP clock, calculated by the local clock, as per IEEE Std
1588-2008, section…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.3.10.1.4
The value of tmnxPtpPeerMonTimeLastCalc indicates the time, since
system startup, when tmnxPtpPeerMonTimeOffsetFrMastNs and
tmnxPtpPeerMonTimeMeanPathDlyNs were last calculated.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
.1.3.6.1.4.1.6527.3.1.2.74.3.10.1.5
The value of tmnxPtpPeerMonTimeOffsetFrMastNs indicates the current
offset of the local PTP clock from a master PTP clock, calculated by
the local clock, as per IEEE Std 1588-2008, section 11.2 when Monitor
Receiver has…
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.3.10.1.6
The value of tmnxPtpPeerMonTimeMeanPathDlyNs indicates the current
value of the mean propagation time between the local PTP clock and a
master PTP clock, calculated by the local clock, as per IEEE Std
1588-2008, section…
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.3.10.1.7
.1.3.6.1.4.1.6527.3.1.2.74.5.1 · 1 row entry · 39 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpClockPacketStatsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpClockPacketStatsTable'
The tmnxPtpClockPacketStatsTable consists of the packet statistics
associated with the Precision Time Protocol (PTP).
tmnxPtpClockPacketStatsEntry row .1.3.6.1.4.1.6527.3.1.2.74.5.1.1
The tmnxPtpClockPacketStatsEntry contain the directional packet
statistics for the Precision Time Protocol (PTP).

Rows are created and destroyed by the system.
Column Syntax OID
The value of tmnxPtpClkPktStatsDirection specifies which direction the
packet statistics for the particular row are accumulated.
TmnxPtpDirection
Type Values:
1rx
2tx
Description:
TmnxPtpDirection specifies which direction packets are travelling in
the system:
rx - Packets are being received by the system.
tx - Packets are being transmitted from the system.
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.1
The value of tmnxPtpClkPktStatsAnnounce indicates the accumulated
packet statistics for PTP Announce messages.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.2
The value of tmnxPtpClkPktStatsSync indicates the accumulated packet
statistics for PTP Sync messages.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.3
The value of tmnxPtpClkPktStatsFollowUp indicates the accumulated
packet statistics for PTP Follow Up messages.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.4
The value of tmnxPtpClkPktStatsDelayRequest indicates the accumulated
packet statistics for PTP Delay Request messages.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.5
The value of tmnxPtpClkPktStatsDelayResp indicates the accumulated
packet statistics for PTP Delay Response messages.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.6
The value of tmnxPtpClkPktStatsSignaling indicates the accumulated
packet statistics for PTP signaling messages.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.7
The value of tmnxPtpClkPktStatsOther indicates the accumulated packet
statistics for all other PTP messages.

This object is accumulated in the 'rx' direction only.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.8
The value of tmnxPtpClkPktStatsUniReqAnno indicates the accumulated
packet statistics for Unicast Request Announce TLVs.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.9
The value of tmnxPtpClkPktStatsUniReqSync indicates the accumulated
packet statistics for Unicast Request Sync TLVs.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.10
The value of tmnxPtpClkPktStatsUniReqDelayRsp indicates the
accumulated packet statistics for Unicast Request Delay Response TLVs.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.11
The value of tmnxPtpClkPktStatsUniGrantAnno indicates the accumulated
packet statistics for Unicast Grant Announce TLVs, where the request
was granted. The request was granted if the duration indicated in the
TLV was n…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.12
The value of tmnxPtpClkPktStatsUniGrantSync indicates the accumulated
packet statistics for Unicast Grant Sync TLVs, where the request was
granted. The request was granted if the duration indicated in the TLV
was non-z…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.13
The value of tmnxPtpClkPktStatsUniGrantDelRsp indicates the accumulated
packet statistics for Unicast Grant Delay Response TLVs, where the
request was granted. The request was granted if the duration indicated
in the T…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.14
The value of tmnxPtpClkPktStatsUniDenyAnno indicates the accumulated
packet statistics for Unicast Grant Announce TLVs, where the request
was denied. The request was denied if the duration indicated in the
TLV was zero.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.15
The value of tmnxPtpClkPktStatsUniDenySync indicates the accumulated
packet statistics for Unicast Grant Sync TLVs, where the request was
denied. The request was denied if the duration indicated in the TLV
was zero.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.16
The value of tmnxPtpClkPktStatsUniDenyDelRsp indicates the accumulated
packet statistics for Unicast Grant Delay Response TLVs, where the
request was denied. The request was denied if the duration indicated
in the TLV …
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.17
The value of tmnxPtpClkPktStatsUniCancelAnno indicates the accumulated
packet statistics for Unicast Cancel Announce TLVs.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.18
The value of tmnxPtpClkPktStatsUniCancelSync indicates the accumulated
packet statistics for Unicast Cancel Sync TLVs.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.19
The value of tmnxPtpClkPktStatsUniCancelDelay indicates the
accumulated packet statistics for Unicast Cancel Delay TLVs.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.20
The value of tmnxPtpClkPktStatsUniAckCnclAnno indicates the
accumulated packet statistics for Unicast Acknowledge Cancel Announce
TLVs.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.21
The value of tmnxPtpClkPktStatsUniAckCnclSync indicates the
accumulated packet statistics for Unicast Acknowledge Cancel Sync
TLVs.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.22
The value of tmnxPtpClkPktStatsUniAckCnclDly indicates the accumulated
packet statistics for Unicast Acknowledge Cancel Delay Response TLVs.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.23
The value of tmnxPtpClkPktStatsOtherTLVs indicates the accumulated
packet statistics for other PTP TLV signaling messages.

This object is accumulated for the 'rx' direction only.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.24
The value of tmnxPtpClkPktStatsDropBadDomain indicates the accumulated
packet statistics for PTP packets dropped because the PTP domain
indicated in the packet does not match the configured PTP domain.

Th…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.25
The value of tmnxPtpClkPktStatsDropAltMaster indicates the accumulated
packet statistics for PTP packets dropped because the PTP header has
the 'alternateMasterFlag' set.

This object is accumulated for th…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.26
The value of tmnxPtpClkPktStatsDropOther indicates the accumulated
packet statistics for PTP packets dropped and not counted in
- tmnxPtpClkPktStatsDropBadDomain
- tmnxPtpClkPktStatsDropAltMaster
- tmnxPtpClkPk…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.27
The value of tmnxPtpClkPktStatsTimeStampPort indicates the accumulated
packet statistics for PTP event packets where the timestamp point is
at the physical layer.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.28
The value of tmnxPtpClkPktStatsTimeStampCpm indicates the accumulated
packet statistics for PTP event packets where the timestamp point is
at the operating system kernel.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.29
The value of tmnxPtpClkPktStatsDropOutOfSeq indicates the accumulated
packet statistics for PTP packets dropped because the packets were
received out of sequence.

This object is accumulated for the 'rx' d…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.30
The value of tmnxPtpClkPktStatsDropPeerShut indicates the accumulated
packet statistics for PTP packets dropped because the packets were
received from a PTP peer that has been administratively disabled.

T…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.31
The value of tmnxPtpClkPktStatsDropPtsf indicates the accumulated
packet statistics for PTP packets dropped because the packet timing
signal from the neighboring clock is considered unusable.

This object …
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.32
The value of tmnxPtpClkPktStatsDropFreerun indicates the accumulated
packet statistics for PTP packets dropped because the central clock is
in freerun.

This object is accumulated for the 'rx' direction on…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.33
The value of tmnxPtpClkPktStatsPDelayRequest indicates the accumulated
packet statistics for PTP Pdelay_Req messages.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.34
The value of tmnxPtpClkPktStatsPDelayResponse indicates the
accumulated packet statistics for PTP Pdelay_Resp messages.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.35
The value of tmnxPtpClkPktStatsPDlyRespFollUp indicates the
accumulated packet statistics for PTP Pdelay_Resp_Follow_Up messages.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.36
The value of tmnxPtpClkPktStatsAnnoC37238Tlv indicates the accumulated
packet statistics for IEEE_C37_238 TLVs in Announce messages.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.37
The value of tmnxPtpClkPktStatsAnnoAtoiTlv indicates the accumulated
packet statistics for ALTERNATE_TIME_OFFSET_INDICATOR TLVs in Announce
messages.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.38
The value of tmnxPtpClkPktStatsAnnoOtherTlv indicates the accumulated
packet statistics for other TLVs in announce messages.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.1.1.39
.1.3.6.1.4.1.6527.3.1.2.74.5.2 · 1 row entry · 32 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpPeerPacketStatsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpPeerPacketStatsTable'
The tmnxPtpPeerPacketStatsTable consists of the per peer packet
statistics associated with the Precision Time Protocol (PTP).
tmnxPtpPeerPacketStatsEntry row .1.3.6.1.4.1.6527.3.1.2.74.5.2.1
The tmnxPtpPeerPacketStatsEntry contain the directional packet
statistics for the Precision Time Protocol (PTP).

Rows are created and destroyed by the system.
Column Syntax OID
The value of tmnxPtpPeerPktStatDirection specifies which direction the
packet statistics for the particular row are accumulated.
TmnxPtpDirection
Type Values:
1rx
2tx
Description:
TmnxPtpDirection specifies which direction packets are travelling in
the system:
rx - Packets are being received by the system.
tx - Packets are being transmitted from the system.
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.1
The value of tmnxPtpPeerPktStatAnnounce indicates the accumulated
packet statistics for PTP Announce messages.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.2
The value of tmnxPtpPeerPktStatSync indicates the accumulated packet
statistics for PTP Sync messages.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.3
The value of tmnxPtpPeerPktStatFollowUp indicates the accumulated
packet statistics for PTP Follow Up messages.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.4
The value of tmnxPtpPeerPktStatDelayRequest indicates the accumulated
packet statistics for PTP Delay Request messages.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.5
The value of tmnxPtpPeerPktStatDelayResp indicates the accumulated
packet statistics for PTP Delay Response messages.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.6
The value of tmnxPtpPeerPktStatSignaling indicates the accumulated
packet statistics for PTP signaling messages.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.7
The value of tmnxPtpPeerPktStatOther indicates the accumulated packet
statistics for all other PTP messages.

This object is accumulated in the 'rx' direction only.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.8
The value of tmnxPtpPeerPktStatUniReqAnno indicates the accumulated
packet statistics for Unicast Request Announce TLVs.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.9
The value of tmnxPtpPeerPktStatUniReqSync indicates the accumulated
packet statistics for Unicast Request Sync TLVs.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.10
The value of tmnxPtpPeerPktStatUniReqDelayRsp indicates the
accumulated packet statistics for Unicast Request Delay Response TLVs.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.11
The value of tmnxPtpPeerPktStatUniGrantAnno indicates the accumulated
packet statistics for Unicast Grant Announce TLVs, where the request
was granted. The request was granted if the duration indicated in the
TLV was …
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.12
The value of tmnxPtpPeerPktStatUniGrantSync indicates the accumulated
packet statistics for Unicast Grant Sync TLVs, where the request was
granted. The request was granted if the duration indicated in the TLV
was non-z…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.13
The value of tmnxPtpPeerPktStatUniGrantDelRsp indicates the accumulated
packet statistics for Unicast Grant Delay Response TLVs, where the
request was granted. The request was granted if the duration indicated
in the T…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.14
The value of tmnxPtpPeerPktStatUniDenyAnno indicates the accumulated
packet statistics for Unicast Grant Announce TLVs, where the request
was denied. The request was denied if the duration indicated in the
TLV was zero.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.15
The value of tmnxPtpPeerPktStatUniDenySync indicates the accumulated
packet statistics for Unicast Grant Sync TLVs, where the request was
denied. The request was denied if the duration indicated in the TLV
was zero.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.16
The value of tmnxPtpPeerPktStatUniDenyDelRsp indicates the accumulated
packet statistics for Unicast Grant Delay Response TLVs, where the
request was denied. The request was denied if the duration indicated
in the TLV …
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.17
The value of tmnxPtpPeerPktStatUniCancelAnno indicates the accumulated
packet statistics for Unicast Cancel Announce TLVs.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.18
The value of tmnxPtpPeerPktStatUniCancelSync indicates the accumulated
packet statistics for Unicast Cancel Sync TLVs.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.19
The value of tmnxPtpPeerPktStatUniCancelDelay indicates the
accumulated packet statistics for Unicast Cancel Delay TLVs.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.20
The value of tmnxPtpPeerPktStatUniAckCnclAnno indicates the
accumulated packet statistics for Unicast Acknowledge Cancel Announce
TLVs.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.21
The value of tmnxPtpPeerPktStatUniAckCnclSync indicates the
accumulated packet statistics for Unicast Acknowledge Cancel Sync
TLVs.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.22
The value of tmnxPtpPeerPktStatUniAckCnclDly indicates the accumulated
packet statistics for Unicast Acknowledge Cancel Delay Response TLVs.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.23
The value of tmnxPtpPeerPktStatOtherTLVs indicates the accumulated
packet statistics for other PTP TLV signaling messages.

This object is accumulated for the 'rx' direction only.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.24
The value of tmnxPtpPeerPktStatDropBadDomain indicates the accumulated
packet statistics for PTP packets dropped because the PTP domain
indicated in the packet does not match the configured PTP domain.

Th…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.25
The value of tmnxPtpPeerPktStatDropAltMaster indicates the accumulated
packet statistics for PTP packets dropped because the PTP header has
the 'alternateMasterFlag' set.

This object is accumulated for th…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.26
The value of tmnxPtpPeerPktStatDropOther indicates the accumulated
packet statistics for PTP packets dropped and not counted in
- tmnxPtpPeerPktStatDropBadDomain
- tmnxPtpPeerPktStatDropAltMaster
- tmnxPtpPeerP…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.27
The value of tmnxPtpPeerPktStatTimeStampPort indicates the accumulated
packet statistics for PTP event packets where the timestamp point is
at the physical layer.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.28
The value of tmnxPtpPeerPktStatTimeStampCpm indicates the accumulated
packet statistics for PTP event packets where the timestamp point is
at the operating system kernel.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.29
The value of tmnxPtpPeerPktStatDropOutOfSeq indicates the accumulated
packet statistics for PTP packets dropped because the packets were
received out of sequence.

This object is accumulated for the 'rx' d…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.30
The value of tmnxPtpPeerPktStatDropPeerShut indicates the accumulated
packet statistics for PTP packets dropped because the packets were
received from a PTP peer that has been administratively disabled.

T…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.31
The value of tmnxPtpPeerPktStatDropFreerun indicates the accumulated
packet statistics for PTP packets dropped because the central clock is
in freerun.

This object is accumulated for the 'rx' direction on…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.2.1.32
.1.3.6.1.4.1.6527.3.1.2.74.5.4 · 1 row entry · 22 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpPortStatsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpPortStatsTable'
The tmnxPtpPortStatsTable contains packet statistics for Ethernet
ports configured for direct transport of PTP over Ethernet.
tmnxPtpPortStatsEntry row .1.3.6.1.4.1.6527.3.1.2.74.5.4.1
The tmnxPtpPortStatsEntry contains the directional packet statistics
for a specific Ethernet port configured for direct transport of PTP
over Ethernet.

Rows are created and destroyed by the system, when cor…
Column Syntax OID
The value of tmnxPtpPortStatDirection specifies which direction the
packet statistics for the particular row are accumulated.
TmnxPtpDirection
Type Values:
1rx
2tx
Description:
TmnxPtpDirection specifies which direction packets are travelling in
the system:
rx - Packets are being received by the system.
tx - Packets are being transmitted from the system.
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.1
The value of tmnxPtpPortStatAnnounce indicates the number of
accumulated PTP Announce packets transmitted or received on the
Ethernet port.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.2
The value of tmnxPtpPortStatSync indicates the number of accumulated
PTP Sync packets transmitted or received on the Ethernet port.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.3
The value of tmnxPtpPortStatFollowUp indicates the number of
accumulated PTP Follow-Up packets transmitted or received on the
Ethernet port.

Because 'tmnxPtpClockStepType' is 'oneStep (1)', the system wil…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.4
The value of tmnxPtpPortStatDelayRequest indicates the number of
accumulated PTP Delay Request packets transmitted or received on the
Ethernet port.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.5
The value of tmnxPtpPortStatDelayResponse indicates the number of
accumulated PTP Delay Response packets transmitted or received on the
Ethernet port.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.6
The value of tmnxPtpPortStatSignaling indicates the number of
accumulated PTP Signaling packets received on the Ethernet port.

This object is accumulated in the 'rx' direction only.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.7
The value of tmnxPtpPortStatOther indicates the number of accumulated
PTP packets of all other types.

This object is accumulated in the 'rx' direction only.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.8
The value of tmnxPtpPortStatTimeStampPort indicates the accumulated
packet statistics for PTP event packets on the Ethernet port where the
timestamp is taken at the physical layer on the Ethernet port.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.9
The value of tmnxPtpPortStatTimeStampCpm indicates the accumulated
packet statistics for PTP event packets where the timestamp is taken
at the operating system kernel on the CPM card.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.10
The value of tmnxPtpPortStatDropBadDomain indicates the accumulated
packet statistics for PTP packets dropped because the PTP domain
indicated in the packet does not match the configured PTP domain.

This …
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.11
The value of tmnxPtpPortStatDropAltMaster indicates the accumulated
packet statistics for PTP packets dropped because the PTP header has
the 'alternateMasterFlag' set.

This object is accumulated for the '…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.12
The value of tmnxPtpPortStatDropOutOfSeq indicates the accumulated
packet statistics for PTP packets dropped because the packets were
received out of sequence.

This object is accumulated for the 'rx' dire…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.13
The value of tmnxPtpPortStatDropOther indicates the accumulated
packet statistics for PTP packets dropped and not counted in
- tmnxPtpPortStatDropBadDomain
- tmnxPtpPortStatDropAltMaster
- tmnxPtpPortStatDropOu…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.14
The value of tmnxPtpPortStatDropPtsf indicates the accumulated packet
statistics for PTP packets dropped because the packet timing signal
from the neighboring clock is considered unusable.

This object is …
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.15
The value of tmnxPtpPortStatDropFreerun indicates the accumulated
packet statistics for PTP packets dropped because the central clock is
in freerun.

This object is accumulated for the 'rx' direction only.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.16
The value of tmnxPtpPortStatPDelayRequest indicates the number of
accumulated PTP Pdelay_Req packets transmitted or received on the
Ethernet port.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.17
The value of tmnxPtpPortStatPDelayResponse indicates the number of
accumulated PTP Pdelay_Resp packets transmitted or received on the
Ethernet port.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.18
The value of tmnxPtpPortStatPDlyRespFollowUp indicates the number of
accumulated PTP Pdelay_Resp_Follow_Up packets transmitted or received
on the Ethernet port.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.19
The value of tmnxPtpPortStatAnnoC37238Tlv indicates the accumulated
packet statistics for IEEE_C37_238 TLVs in Announce messages
transmitted or received on the Ethernet port.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.20
The value of tmnxPtpPortStatAnnoAtoiTlv indicates the accumulated
packet statistics for ALTERNATE_TIME_OFFSET_INDICATOR TLVs in Announce
messages transmitted or received on the Ethernet port.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.21
The value of tmnxPtpPortStatAnnoOtherTlv indicates the accumulated
packet statistics for other TLVs in announce messages transmitted or
received on the Ethernet port.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.4.1.22
.1.3.6.1.4.1.6527.3.1.2.74.5.5 · 1 row entry · 11 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpPacketRateStatsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpPacketRateStatsTable'
The tmnxPtpPacketRateStatsTable contains packet rate statistics for
PTP.
tmnxPtpPacketRateStatsEntry row .1.3.6.1.4.1.6527.3.1.2.74.5.5.1
A tmnxPtpPacketRateStatsEntry contains the current observed rate of
PTP packets transmitted or received over either UDP/IP or directly
over Ethernet.

The packet rates in each entry are aggregated based on t…
Column Syntax OID
The value of tmnxPtpPacketRateStatsTransport specifies the transport
type of the PTP packets whose rate is calculated.
TmnxPtpTransportType
Type Values:
1none
2udpIp
3ethernet
Description:
TmnxPtpTransportType indicates the transport type of the PTP packets
exchanged between two PTP clocks.

Values:
none (1) - this value is used to indicate that there is no
exchange of…
.1.3.6.1.4.1.6527.3.1.2.74.5.5.1.1
The value of tmnxPtpPacketRateStatsDirection specifies which direction
the packet rates for the particular row are calculated.
TmnxPtpDirection
Type Values:
1rx
2tx
Description:
TmnxPtpDirection specifies which direction packets are travelling in
the system:
rx - Packets are being received by the system.
tx - Packets are being transmitted from the system.
.1.3.6.1.4.1.6527.3.1.2.74.5.5.1.2
The value of tmnxPtpPacketRateStatsAnnounce indicates the rate of PTP
announce packets transmitted or received by the local PTP clock.
packets per decasecondSNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.5.1.3
The value of tmnxPtpPacketRateStatsSync indicates the rate of PTP sync
packets transmitted or received by the local PTP clock over either
UDP/IP or Ethernet.
packets per decasecondSNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.5.1.4
The value of tmnxPtpPacketRateStatsFollowUp indicates the rate of PTP
follow-up packets transmitted or received by the local PTP clock.

When tmnxPtpPacketRateStatsDirection is 'tx (2)',
tmnxPtpPacketRateS…
packets per decasecondSNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.5.1.5
The value of tmnxPtpPacketRateStatsDelayReq indicates the rate of PTP
delay request packets transmitted or received by the local PTP clock.
packets per decasecondSNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.5.1.6
The value of tmnxPtpPacketRateStatsDelayResp indicates the rate of PTP
delay response packets transmitted or received by the local PTP clock.
packets per decasecondSNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.5.1.7
The value of tmnxPtpPacketRateStatsOther indicates the rate of PTP
packets of all other types not covered by the previous five objects,
which are transmitted or received by the local PTP clock.

When tmnxP…
packets per decasecondSNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.5.1.8
The value of tmnxPtpPacketRateStatsPDelayReq indicates the rate of PTP
Pdelay_Req packets transmitted or received by the local PTP clock.
packets per decasecondSNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.5.1.9
The value of tmnxPtpPacketRateStatsPDelayResp indicates the rate of
PTP Pdelay_Resp packets transmitted or received by the local PTP
clock.
packets per decasecondSNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.5.1.10
The value of tmnxPtpPktRateStatsPDlyRespFolUp indicates the rate of
PTP Pdelay_Resp_Follow_Up packets transmitted or received by the local
PTP clock.
packets per decasecondSNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.5.1.11
.1.3.6.1.4.1.6527.3.1.2.74.5.6 · 1 row entry · 37 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpPerfMonitoringTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpPerfMonitoringTable'
The tmnxPtpPerfMonitoringTable is used for PTP performance monitoring
statistics as described in IEEE Std 1588-2019 Annex J, Table J.1
tmnxPtpPerfMonitoringEntry row .1.3.6.1.4.1.6527.3.1.2.74.5.6.1
PTP Instance Performance Monitoring statistics, related to the PTP
Port or Link Port in the slave state.
Column Syntax OID
Index to each record in the list.
TmnxPtpPerfMonIndexType
Type Constraints:
range: 0..98
range: 501..516
Description:
Index to each record of performance monitoring. Values supported are:
0 : current 15 minute interval,
1..96 : previous 15 minute intervals (1 being the most recent),
97 : current 24 hour interval,
98 : previous 24 hour …
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.1
tmnxPtpPerfMonMeasureValid indicates the data can be correctly
interpreted. For example, if for some periods the data is not valid
for part of the data collection interval (e.g. the clock is not
receiving any PTP timing…
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.2
tmnxPtpPerfMonPeriodComplete is set to true when the recording period
closes and measurements were performed during the entire period (1
minute, 15 minute, or 24 hour).

For example, if the PTP instance is…
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.3
tmnxPtpPerfMonStartTime indicates the time of the beginning of the
measurement record.
SNMPv2-TCDateAndTime
Type Constraints:
range: 8
range: 11
Description:
A date-time specification.

field octets contents range
----- ------ -------- -----
1 1-2 year* 0..65536
2 3 month …
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.4
tmnxPtpPerfMonDuration indicates the amount of time, in seconds, for
which the data for this record was collected
secondsSNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.5
tmnxPtpPerfMonAvgMastSlavDly indicates the average of the master-slave
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.6
tmnxPtpPerfMonMinMastSlavDly indicates the Minimum of the master-slave
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.7
tmnxPtpPerfMonMaxMastSlavDly indicates the maximum of the master-slave
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.8
tmnxPtpPerfMonSDevMastSlavDly indicates the standard deviation of the
master-slave delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.9
tmnxPtpPerfMonAvgSlavMastDly indicates the average of the slave-master
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.10
tmnxPtpPerfMonMinSlavMastDly indicates the minimum of the slave-master
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.11
tmnxPtpPerfMonMaxSlavMastDly indicates the maximum of the slave-master
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.12
tmnxPtpPerfMonSDevSlavMastDly indicates the standard deviation of the
slave-master delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.13
tmnxPtpPerfMonAvgMeanPathDly indicates the average of the mean path
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.14
tmnxPtpPerfMonMinMeanPathDly indicates the minimum of the mean path
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.15
tmnxPtpPerfMonMaxMeanPathDly indicates the maximum of the mean path
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.16
tmnxPtpPerfMonSDevMeanPathDly indicates the standard deviation of the
mean path delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.17
tmnxPtpPerfMonAvgOffsetFrMaster indicates the average of the offset
from master for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.18
tmnxPtpPerfMonMinOffsetFrMaster indicates the minimum of the offset
from master for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.19
tmnxPtpPerfMonMaxOffsetFrMaster indicates the maximum of the offset
from master for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.20
tmnxPtpPerfMonSDevOffsetFrMaster indicates the standard deviation of
the offset from master for this interval. An invalid value (not
measured correctly) shall be indicated with one in all bits, except
the most significa…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.21
tmnxPtpPMonAvgMastSlavDlyNs indicates the average of the master-slave
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.22
tmnxPtpPMonMinMastSlavDlyNs indicates the Minimum of the master-slave
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.23
tmnxPtpPMonMaxMastSlavDlyNs indicates the maximum of the master-slave
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.24
tmnxPtpPMonSDevMastSlavDlyNs indicates the standard deviation of the
master-slave delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.25
tmnxPtpPMonAvgSlavMastDlyNs indicates the average of the slave-master
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.26
tmnxPtpPMonMinSlavMastDlyNs indicates the minimum of the slave-master
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.27
tmnxPtpPMonMaxSlavMastDlyNs indicates the maximum of the slave-master
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.28
tmnxPtpPMonSDevSlavMastDlyNs indicates the standard deviation of the
slave-master delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.29
tmnxPtpPMonAvgMeanPathDlyNs indicates the average of the mean path
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.30
tmnxPtpPMonMinMeanPathDlyNs indicates the minimum of the mean path
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.31
tmnxPtpPMonMaxMeanPathDlyNs indicates the maximum of the mean path
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.32
tmnxPtpPMonSDevMeanPathDlyNs indicates the standard deviation of the
mean path delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.33
tmnxPtpPMonAvgOffsetFrMasterNs indicates the average of the offset
from master for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.34
tmnxPtpPMonMinOffsetFrMasterNs indicates the minimum of the offset
from master for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.35
tmnxPtpPMonMaxOffsetFrMasterNs indicates the maximum of the offset
from master for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.36
tmnxPtpPMonSDevOffsetFrMasterNs indicates the standard deviation of
the offset from master for this interval. An invalid value (not
measured correctly) shall be indicated with one in all bits, except
the most significan…
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.6.1.37
.1.3.6.1.4.1.6527.3.1.2.74.5.7 · 1 row entry · 37 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpPeerPerfMonitoringTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpPeerPerfMonitoringTable'
The tmnxPtpPeerPerfMonitoringTable is used for PTP peer performance
monitoring statistics when Monitor Receiver has been enabled on a
peer, as described in IEEE Std 1588-2019 Annex J, Table J.1
tmnxPtpPeerPerfMonitoringEntry row .1.3.6.1.4.1.6527.3.1.2.74.5.7.1
Peer Instance Performance Monitoring statistics, related to the PTP
Peer when Monitor Receiver has been enabled.
Column Syntax OID
Index to each record in the list.
TmnxPtpPerfMonIndexType
Type Constraints:
range: 0..98
range: 501..516
Description:
Index to each record of performance monitoring. Values supported are:
0 : current 15 minute interval,
1..96 : previous 15 minute intervals (1 being the most recent),
97 : current 24 hour interval,
98 : previous 24 hour …
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.1
tmnxPtpPeerPerfMonMeasureValid indicates the data can be correctly
interpreted. For example, if for some periods the data is not valid
for part of the data collection interval (e.g. the clock is not
receiving any PTP ti…
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.2
tmnxPtpPeerPerfMonPeriodComplete is set to true when the recording
period closes and measurements were performed during the entire period
(1 minute, 15 minute, or 24 hour).

For example, if the PTP instanc…
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.3
tmnxPtpPeerPerfMonStartTime indicates the time of the beginning of the
measurement record.
SNMPv2-TCDateAndTime
Type Constraints:
range: 8
range: 11
Description:
A date-time specification.

field octets contents range
----- ------ -------- -----
1 1-2 year* 0..65536
2 3 month …
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.4
tmnxPtpPeerPerfMonDuration indicates the amount of time, in seconds,
for which the data for this record was collected
secondsSNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.5
tmnxPtpPeerPerfMonAvgMastSlavDly indicates the average of the
master-slave delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.6
tmnxPtpPeerPerfMonMinMastSlavDly indicates the Minimum of the
master-slave delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.7
tmnxPtpPeerPerfMonMaxMastSlavDly indicates the maximum of the
master-slave delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.8
tmnxPtpPeerPerfMonSDMastSlavDly indicates the standard deviation of
the master-slave delay for this interval. An invalid value (not
measured correctly) shall be indicated with one in all bits, except
the most significan…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.9
tmnxPtpPeerPerfMonAvgSlavMastDly indicates the average of the
slave-master delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.10
tmnxPtpPeerPerfMonMinSlavMastDly indicates the minimum of the
slave-master delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.11
tmnxPtpPeerPerfMonMaxSlavMastDly indicates the maximum of the
slave-master delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.12
tmnxPtpPeerPerfMonSDSlavMastDly indicates the standard deviation of
the slave-master delay for this interval. An invalid value (not
measured correctly) shall be indicated with one in all bits, except
the most significan…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.13
tmnxPtpPeerPerfMonAvgMeanPathDly indicates the average of the mean
path delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.14
tmnxPtpPeerPerfMonMinMeanPathDly indicates the minimum of the mean
path delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.15
tmnxPtpPeerPerfMonMaxMeanPathDly indicates the maximum of the mean
path delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.16
tmnxPtpPeerPerfMonSDMeanPathDly indicates the standard deviation of
the mean path delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.17
tmnxPtpPeerPerfMonAvgOffFrMaster indicates the average of the offset
from master for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.18
tmnxPtpPeerPerfMonMinOffFrMaster indicates the minimum of the offset
from master for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.19
tmnxPtpPeerPerfMonMaxOffFrMaster indicates the maximum of the offset
from master for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.20
tmnxPtpPeerPerfMonSDOffFrMaster indicates the standard deviation of
the offset from master for this interval. An invalid value (not
measured correctly) shall be indicated with one in all bits, except
the most significan…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.21
tmnxPtpPeerPMonAvgMastSlavDlyNs indicates the average of the
master-slave delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.22
tmnxPtpPeerPMonMinMastSlavDlyNs indicates the Minimum of the
master-slave delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.23
tmnxPtpPeerPMonMaxMastSlavDlyNs indicates the maximum of the
master-slave delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.24
tmnxPtpPeerPMonSDMastSlavDlyNs indicates the standard deviation of the
master-slave delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.25
tmnxPtpPeerPMonAvgSlavMastDlyNs indicates the average of the
slave-master delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.26
tmnxPtpPeerPMonMinSlavMastDlyNs indicates the minimum of the
slave-master delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.27
tmnxPtpPeerPMonMaxSlavMastDlyNs indicates the maximum of the
slave-master delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.28
tmnxPtpPeerPMonSDSlavMastDlyNs indicates the standard deviation of the
slave-master delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.29
tmnxPtpPeerPMonAvgMeanPathDlyNs indicates the average of the mean path
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.30
tmnxPtpPeerPMonMinMeanPathDlyNs indicates the minimum of the mean path
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.31
tmnxPtpPeerPMonMaxMeanPathDlyNs indicates the maximum of the mean path
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.32
tmnxPtpPeerPMonSDMeanPathDlyNs indicates the standard deviation of the
mean path delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.33
tmnxPtpPeerPMonAvgOffFrMasterNs indicates the average of the offset
from master for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.34
tmnxPtpPeerPMonMinOffFrMasterNs indicates the minimum of the offset
from master for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.35
tmnxPtpPeerPMonMaxOffFrMasterNs indicates the maximum of the offset
from master for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.36
tmnxPtpPeerPMonSDOffFrMasterNs indicates the standard deviation of the
offset from master for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.7.1.37
.1.3.6.1.4.1.6527.3.1.2.74.5.8 · 1 row entry · 37 columns
Uses the nokia variant from /opt/observium/mibs/nokia.
Command help
Walk tmnxPtpPortPerfMonitoringTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'TIMETRA-PTP-MIB' -M '/opt/observium/mibs/nokia:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'TIMETRA-PTP-MIB::tmnxPtpPortPerfMonitoringTable'
The tmnxPtpPortPerfMonitoringTable is used for PTP port neighbor
performance monitoring statistics when Monitor Receiver has been
enabled on a port, as described in IEEE Std 1588-2019 Annex J, Table
J.1
tmnxPtpPortPerfMonitoringEntry row .1.3.6.1.4.1.6527.3.1.2.74.5.8.1
Port Instance Performance Monitoring statistics, related to the PTP
Port when Monitor Receiver has been enabled.
Column Syntax OID
Index to each record in the list.
TmnxPtpPerfMonIndexType
Type Constraints:
range: 0..98
range: 501..516
Description:
Index to each record of performance monitoring. Values supported are:
0 : current 15 minute interval,
1..96 : previous 15 minute intervals (1 being the most recent),
97 : current 24 hour interval,
98 : previous 24 hour …
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.1
tmnxPtpPortPerfMonMeasureValid indicates the data can be correctly
interpreted. For example, if for some periods the data is not valid
for part of the data collection interval (e.g. the clock is not
receiving any PTP ti…
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.2
tmnxPtpPortPerfMonPeriodComplete is set to true when the recording
period closes and measurements were performed during the entire period
(1 minute, 15 minute, or 24 hour).

For example, if the PTP instanc…
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.3
tmnxPtpPortPerfMonStartTime indicates the time of the beginning of the
measurement record.
SNMPv2-TCDateAndTime
Type Constraints:
range: 8
range: 11
Description:
A date-time specification.

field octets contents range
----- ------ -------- -----
1 1-2 year* 0..65536
2 3 month …
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.4
tmnxPtpPortPerfMonDuration indicates the amount of time, in seconds,
for which the data for this record was collected
secondsSNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.5
tmnxPtpPortPerfMonAvgMastSlavDly indicates the average of the
master-slave delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.6
tmnxPtpPortPerfMonMinMastSlavDly indicates the Minimum of the
master-slave delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.7
tmnxPtpPortPerfMonMaxMastSlavDly indicates the maximum of the
master-slave delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.8
tmnxPtpPortPerfMonSDMastSlavDly indicates the standard deviation of
the master-slave delay for this interval. An invalid value (not
measured correctly) shall be indicated with one in all bits, except
the most significan…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.9
tmnxPtpPortPerfMonAvgSlavMastDly indicates the average of the
slave-master delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.10
tmnxPtpPortPerfMonMinSlavMastDly indicates the minimum of the
slave-master delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.11
tmnxPtpPortPerfMonMaxSlavMastDly indicates the maximum of the
slave-master delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.12
tmnxPtpPortPerfMonSDSlavMastDly indicates the standard deviation of
the slave-master delay for this interval. An invalid value (not
measured correctly) shall be indicated with one in all bits, except
the most significan…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.13
tmnxPtpPortPerfMonAvgMeanPathDly indicates the average of the mean
path delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.14
tmnxPtpPortPerfMonMinMeanPathDly indicates the minimum of the mean
path delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.15
tmnxPtpPortPerfMonMaxMeanPathDly indicates the maximum of the mean
path delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.16
tmnxPtpPortPerfMonSDMeanPathDly indicates the standard deviation of
the mean path delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.17
tmnxPtpPortPerfMonAvgOffFrMaster indicates the average of the offset
from master for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.18
tmnxPtpPortPerfMonMinOffFrMaster indicates the minimum of the offset
from master for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.19
tmnxPtpPortPerfMonMaxOffFrMaster indicates the maximum of the offset
from master for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.20
tmnxPtpPortPerfMonSDOffFrMaster indicates the standard deviation of
the offset from master for this interval. An invalid value (not
measured correctly) shall be indicated with one in all bits, except
the most significan…
TmnxPtpTimeInterval
Type Constraints:
range: 8
Description:
TmnxPtpTimeInterval is an octet string encoding a signed time interval,
in scaled nanoseconds. The signed time interval is encoded as a 64-bit
two's complement integer, in network byte order. The time interval in
nano…
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.21
tmnxPtpPortPMonAvgMastSlavDlyNs indicates the average of the
master-slave delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.22
tmnxPtpPortPMonMinMastSlavDlyNs indicates the Minimum of the
master-slave delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.23
tmnxPtpPortPMonMaxMastSlavDlyNs indicates the maximum of the
master-slave delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.24
tmnxPtpPortPMonSDMastSlavDlyNs indicates the standard deviation of the
master-slave delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.25
tmnxPtpPortPMonAvgSlavMastDlyNs indicates the average of the
slave-master delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.26
tmnxPtpPortPMonMinSlavMastDlyNs indicates the minimum of the
slave-master delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.27
tmnxPtpPortPMonMaxSlavMastDlyNs indicates the maximum of the
slave-master delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.28
tmnxPtpPortPMonSDSlavMastDlyNs indicates the standard deviation of the
slave-master delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.29
tmnxPtpPortPMonAvgMeanPathDlyNs indicates the average of the mean path
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.30
tmnxPtpPortPMonMinMeanPathDlyNs indicates the minimum of the mean path
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.31
tmnxPtpPortPMonMaxMeanPathDlyNs indicates the maximum of the mean path
delay for this interval. An invalid value (not measured correctly)
shall be indicated with one in all bits, except the most significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.32
tmnxPtpPortPMonSDMeanPathDlyNs indicates the standard deviation of the
mean path delay for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.33
tmnxPtpPortPMonAvgOffFrMasterNs indicates the average of the offset
from master for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.34
tmnxPtpPortPMonMinOffFrMasterNs indicates the minimum of the offset
from master for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.35
tmnxPtpPortPMonMaxOffFrMasterNs indicates the maximum of the offset
from master for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.36
tmnxPtpPortPMonSDOffFrMasterNs indicates the standard deviation of the
offset from master for this interval. An invalid value (not measured
correctly) shall be indicated with one in all bits, except the most
significant.
nanosecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.6527.3.1.2.74.5.8.1.37