PKTC-EXCENTIS-SIG-MIB Table View

This table describes the MTA supported codec types. An MTA 
MUST populate this table with all possible combinations of 
codecs it supports for simultaneous operation. For 
example, an MTA with two endpoints may be designed with a 
particular DSP and memory architecture that allows it to 
support the following fixed combinations of codecs for 
simultaneous operation: 
          
Codec Type     Maximum Number of Simultaneous Codecs 
PCMA                             3 
          
PCMA                             2 
PCMU                             1 
          
PCMA                             1 
PCMU                             2 
          
PCMU                             3 
          
PCMA                             1 
G729                             1 
          
G729                             2 
          
PCMU                             1 
G729                             1 
          
Based on this example, the entries in the codec table 
would be: 
          
CodecComboIndex pktcSigDevCodecType pktcSigDevCodecMax 
       1               pcma                3 
          
          
       2               pcma                2 
       2               pcmu                1 
       3               pcma                1 
       3               pcmu                2 
       4               pcmu                3 
       5               pcma                1 
       5               g729                1 
       6               g729                2 
       7               pcmu                1 
       7               g729                1 
          
An operator querying this table is able to determine all 
possible codec combinations the MTA is capable of 
simultaneously supporting. 
This table MUST NOT include non-voice codecs.

pktcSigDevCodecEntry row .1.3.6.1.4.1.7432.2.1.1.1.1

Each entry represents the maximum number of active
connections with a particular codec the MTA is capable of
supporting. Each row is indexed by a composite key
consisting of a number enumerating the particular codec …

Indexes

pktcSigDevCodecComboIndex pktcSigDevCodecType

Column	Syntax	OID
pktcSigDevCodecComboIndex The index value which enumerates a particular codec combination in the pktcSigDevCodecTable.	Unsigned32 Constraints: range: 1-255	.1.3.6.1.4.1.7432.2.1.1.1.1.1
pktcSigDevCodecType A codec type supported by this MTA.	PktcCodecType Type Values: 1 other 2 unknown 3 g729 4 reserved 5 g729E 6 pcmu 7 g726at32 8 g728 9 pcma 10 g726at16 11 g726at24 12 g726at40 13 ilbc 14 bv16	.1.3.6.1.4.1.7432.2.1.1.1.1.2
pktcSigDevCodecMax The maximum number of simultaneous sessions of a particular codec that the MTA can support.	Unsigned32 Constraints: range: 1-255	.1.3.6.1.4.1.7432.2.1.1.1.1.3

This table describes the signaling types supported by this 
MTA.

pktcSigCapabilityEntry row .1.3.6.1.4.1.7432.2.1.1.17.1

Entries in pktcMtaDevSigCapabilityTable - List of
supported signaling types, versions and vendor extensions


for this MTA. Each entry in the list provides for one
signaling type and version c…

Indexes

pktcSignalingIndex

Column	Syntax	OID
pktcSignalingIndex The index value which uniquely identifies an entry in the pktcSigCapabilityTable.	Unsigned32 Constraints: range: 1-255	.1.3.6.1.4.1.7432.2.1.1.17.1.1
pktcSignalingType This object identifies the type of signaling used. This value has to be associated with a single signaling version.	PktcSigType Type Values: 1 other 2 reserved 3 ncs	.1.3.6.1.4.1.7432.2.1.1.17.1.2
pktcSignalingVersion Provides the version of the signaling type - reference pktcSignalingType. Examples would be 1.0 or 2.33 etc.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.7432.2.1.1.17.1.3
pktcSignalingVendorExtension The vendor extension allows vendors to provide a list of additional capabilities, vendors can decide how to encode these extensions, although space separated text is suggested.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.7432.2.1.1.17.1.4

The Pulse signal table defines the pulse signal operation. 
There are nine types of international pulse signals, 
with each signal having a set of provisionable parameters. 
The values of the MIB objects in this table take effect 
only if these parameters are not defined via signaling, in 
which case the latter determines the values of the 
parameters. This object is required for the E line 
package. Signals defined in this table are triggered using 
the E line package. 
Objects in this table do not persist across MTA reboots.

pktcSigPulseSignalEntry row .1.3.6.1.4.1.7432.2.1.1.20.1

This object defines the set of parameters associated with
each particular value of pktcSigPulseSignalType. Each
entry in the pktcSigPulseSignalTable is indexed by the
pktcSigPulseSignalType object.

Indexes

pktcSigPulseSignalType

Column	Syntax	OID
pktcSigPulseSignalType There are nine types of international pulse signals. These signals are defined as follows: initial ring pulse loop close pulse loop open enable meter pulse meter pulse burst pulse no battery pulse normal polarit…	Enumeration Enumerated Values: 1 initialRing 2 pulseLoopClose 3 pulseLoopOpen 4 enableMeterPulse 5 meterPulseBurst 6 pulseNoBattery 7 pulseNormalPolarity 8 pulseReducedBattery 9 pulseReversePolarity	.1.3.6.1.4.1.7432.2.1.1.20.1.1
pktcSigPulseSignalFrequency This object is only applicable to the initialRing, enableMeterPulse, and meterPulseBurst signal type. This object identifies the frequency of the generated signal. The following table defines the default values for t…	HertzEnumerationr/w Enumerated Values: 1 twentyfive 2 twelvethousand 3 sixteenthousand	.1.3.6.1.4.1.7432.2.1.1.20.1.2
pktcSigPulseSignalDbLevel This object is only applicable to the enableMeterPulse and meterPulseBurst signal types. This is the decibel level for each frequency at which tones could be generated at the a and b terminals (TE connection point). …	dBmInteger32r/w Constraints: range: -350-0	.1.3.6.1.4.1.7432.2.1.1.20.1.3
pktcSigPulseSignalDuration This object specifies the pulse duration for each signal type. In addition, the MTA must accept the values in the incremental steps specific for each signal type. The following table defines the default values and th…	MillisecondsUnsigned32r/w Constraints: range: 0-5000	.1.3.6.1.4.1.7432.2.1.1.20.1.4
pktcSigPulseSignalPulseInterval This object specifies the repeat interval, or the period for each signal type. In addition, the MTA must accept the values in the incremental steps specific for each signal type. The following table defines the defau…	MillisecondsUnsigned32r/w Constraints: range: 0-5000	.1.3.6.1.4.1.7432.2.1.1.20.1.5
pktcSigPulseSignalRepeatCount This object specifies how many times to repeat a pulse. This object is not used by the enableMeterPulse signal type and as such must have a value of zero. The following table defines the…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.1.20.1.6

Cadence rings are defined by the telco governing 
body for each country. The MTA must be able to support 
various ranges of cadence patterns and cadence periods. 
The MTA will be able to support country specific 
provisioning of the cadence and idle period. Each 
cadence pattern will be assigned a unique value ranging 
from 0-127 (inclusive) corresponding to the value of x, 
where x is the value sent in the cadence ringing (cr) 
signal cr(x), requested per the appropriate NCS 
message, and defined in the E package. The MTA will derive 
the cadence periods from the ring cadence table entry as 
provisioned by the customer. The MTA is allowed to provide 
appropriate default values for each of the ring cadences. 
This table only needs to be supported when the MTA 
implements the E package. Objects in this table do not 
persist across MTA reboots.

pktcSigDevRingCadenceEntry row .1.3.6.1.4.1.7432.2.1.1.31.1

Unique value ranging from 0 to 127 that will correspond to
the different ring cadences that are being supported by
the device.

Indexes

pktcSigDevRingCadenceIndex

Column	Syntax	OID
pktcSigDevRingCadenceIndex Unique value ranging from 0 to 127 that corresponds to the value sent by the LE based on country specific cadences, one row per cadence cycle. In any given system implementation for a particular country, it is antici…	Unsigned32 Constraints: range: 0-127	.1.3.6.1.4.1.7432.2.1.1.31.1.1
pktcSigDevRingCadence This is the Ring Cadence. This object is required for the E line package.	PktcRingCadencer/w Type Constraints: range: 4..36	.1.3.6.1.4.1.7432.2.1.1.31.1.2

The Tone Table defines the various tone operations. Any 
definition of the tones callWaiting1-4 in this table 
should just contain the audible tone itself and NOT 
contain the delay between tones or the tone repeat count. 
The delay between tones or the repeat count is controlled 
by the objects pktcNcsEndPntConfigCallWaitingDelay, and 
          
          
pktcNcsEndPntConfigCallWaitingMaxRep. If the  
pktcSigDevToneType is set to either of the values 
callWaiting1, callWaiting2, callWaiting3 or callWaiting4, 
then the value of the pktcSigDevToneWholeToneRepeatCount 
object has no effect on the tone. The MTA MUST 
make sure that, after the provisioning cycle, the table is 
fully populated (i.e., for each possible index, an entry 
MUST be defined) using reasonable defaults for each row 
that was not defined by the provisioning information 
delivered by the MTA Configuration File. 
The frequency composition of each tone is defined by the  
pktcSigDevMultiFreqToneTable. For each ToneType defined  
in pktcSigDevToneTable, the MTA MUST populate at least 
one entry in the pktcSigDevMultiFreqToneTable. 
Objects in this table do not persist across MTA reboots. 
For tones with multiple frequencies refer to the MIB table 
pktcSigDevMultiFreqToneTable.

pktcSigDevToneEntry row .1.3.6.1.4.1.7432.2.1.1.32.1

The different tone types that can be provisioned based on
country specific needs.
Each entry contains the tone generation parameters for
a specific Tone Type. The different parameters can be
provisioned by the MTA…

Indexes

pktcSigDevToneType

Column	Syntax	OID
pktcSigDevToneType Unique value that will correspond to the different tone types. These tones can be provisioned based on country specific needs. This object defines the type of tone being accessed. The alertingSignal, specialDial…	Enumeration Enumerated Values: 1 busy 2 confirmation 3 dial 4 messageWaiting 5 offHookWarning 6 ringBack 7 reOrder 8 stutterdial 9 callWaiting1 10 callWaiting2 11 callWaiting3 12 callWaiting4 13 alertingSignal 14 specialDial 15 specialInfo 16 release 17 congestion 18 userDefined1 19 userDefined2 20 userDefined3 21 userDefined4	.1.3.6.1.4.1.7432.2.1.1.32.1.1
pktcSigDevToneWholeToneRepeatCount This is the repeat count, which signifies how many times to repeat the entire on-off cadence sequence. Setting this object may result in a cadence duration longer or shorter than the overall signal duration specifie…	Unsigned32r/w Constraints: range: 0-5000	.1.3.6.1.4.1.7432.2.1.1.32.1.2
pktcSigDevToneSteady This is the steady tone. Device must play out the on-off cadence sequence for pktcSigDevToneWholeRepeatCount times and then apply the last tone forever. Setting this object may result in a tone duration longer or sh…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7432.2.1.1.32.1.3

This MIB table defines the characteristics of tones 
with multiple frequencies. The constraints imposed 
on the tones by the MIB table pktcSigDevToneTable 
          
          
need to be considered for MIB objects in this table 
as well. 
The MTA MUST populate the corresponding row(s)  
of the pktcSigDevMultiFreqToneTable for each tone  
defined in the pktcSigDevToneTable.  
The contents of the table may be provisioned using  
the MTA configuration file.

pktcSigDevMultiFreqToneEntry row .1.3.6.1.4.1.7432.2.1.1.33.1

The different tone types with multiple frequencies
that can be provisioned based on country specific
needs.

Indexes

pktcSigDevToneType pktcSigDevToneNumber

Column	Syntax	OID
pktcSigDevToneNumber This MIB Object represents the frequency reference of a multi-frequency tone.	Unsigned32 Constraints: range: 1-8	.1.3.6.1.4.1.7432.2.1.1.33.1.1
pktcSigDevToneFirstFreqValue This MIB Object represents the value of the first frequency of a tone type. A value of Zero implies absence of the referenced frequency.	Unsigned32r/w Constraints: range: 0-4000	.1.3.6.1.4.1.7432.2.1.1.33.1.2
pktcSigDevToneSecondFreqValue This MIB Object represents the value of the second frequency of a tone type. A value of Zero implies absence of the referenced frequency.	Unsigned32r/w Constraints: range: 0-4000	.1.3.6.1.4.1.7432.2.1.1.33.1.3
pktcSigDevToneThirdFreqValue This MIB Object represents the value of the third frequency of a tone type. A value of Zero implies absence of the referenced frequency.	Unsigned32r/w Constraints: range: 0-4000	.1.3.6.1.4.1.7432.2.1.1.33.1.4
pktcSigDevToneFourthFreqValue This MIB Object represents the value of the fourth frequency of a tone type. A value of Zero implies absence of the referenced frequency.	Unsigned32r/w Constraints: range: 0-4000	.1.3.6.1.4.1.7432.2.1.1.33.1.5
pktcSigDevToneFreqMode This MIB Object provides directive on the modulation or summation of the frequencies involved in the tone. It is to be noted that while summation can be done without any …	Enumerationr/w Enumerated Values: 1 firstModulatedBySecond 2 summation	.1.3.6.1.4.1.7432.2.1.1.33.1.6
pktcSigDevToneFreqAmpModePrtg This MIB Object represents the percentage of amplitude modulation applied to the second frequency when the MIB Object 'pktcSigDevToneFreqMode' is set to a value of 'firstModulatedBySecond (1)'. If th…	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.7432.2.1.1.33.1.7
pktcSigDevToneDbLevel This MIB Object contains the decibel level for each analog signal (tone) that is locally generated (versus in band supervisory tones) and sourced to the a-b terminals (TE connection point). Each tone …	dBmInteger32r/w Constraints: range: -250--30	.1.3.6.1.4.1.7432.2.1.1.33.1.8
pktcSigDevToneFreqOnDuration This MIB Object represents the duration for which the frequency reference corresponding to the tone type is turned on.	Unsigned32r/w Constraints: range: 0-5000	.1.3.6.1.4.1.7432.2.1.1.33.1.9
pktcSigDevToneFreqOffDuration This MIB Object represents the duration for which the frequency reference corresponding to the tone type is turned off.	Unsigned32r/w Constraints: range: 0-5000	.1.3.6.1.4.1.7432.2.1.1.33.1.10
pktcSigDevToneFreqRepeatCount This MIB Object indicates the number of times to repeat the cadence cycle represented by the on/off durations (refer to the MIB Objects pktcSigDevToneFreqOnDuration and pktcSigDevTon…	Unsigned32r/w Constraints: range: 0-5000	.1.3.6.1.4.1.7432.2.1.1.33.1.11

This table describes the information pertaining to each 
endpoint of the MTA. All entries in this table represent 
the provisioned endpoints provisioned with the information 
required by the MTA to maintain the NCS signaling protocol 
communication with the CMS. Each endpoint can be assigned 
to its own CMS. If the specific endpoint does not have 
the corresponding CMS information in this table, the 
endpoint is considered as not provisioned with voice 
services. Objects in this table do not persist across 
MTA reboots.

pktcNcsEndPntConfigEntry row .1.3.6.1.4.1.7432.2.1.2.1.1

Each entry in the pktcNcsEndPntConfigTable represents
required signaling parameters for the specific endpoint
provisioned with voice services.

Indexes

IF-MIBifIndex

Column	Syntax	OID
pktcNcsEndPntConfigCallAgentId This object contains a string indicating the call agent name (e.g.: ca@example.com). The call agent name, after the character '@', MUST be a fully qualified domain name (FQDN) and MUST have a corresponding pktcMtaDev…	OctetStringr/w Constraints: range: 3-255	.1.3.6.1.4.1.7432.2.1.2.1.1.1
pktcNcsEndPntConfigCallAgentUdpPort This object contains the current value of the User Datagram Protocol (UDP) receive port on which the call agent will receive NCS signaling from the endpoint. For each particular endpoint, the MTA MUST use the current…	Unsigned32r/w Constraints: range: 1025-65535	.1.3.6.1.4.1.7432.2.1.2.1.1.2
pktcNcsEndPntConfigPartialDialTO This object contains the value of the partial dial time out.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.3
pktcNcsEndPntConfigCriticalDialTO This object contains the value of the critical dial time out.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.4
pktcNcsEndPntConfigBusyToneTO This object contains the default timeout value for busy tone. The MTA MUST NOT update this object with the value provided in the NCS message (if present). If the value of the object is modified by the SNMP Management…	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.5
pktcNcsEndPntConfigDialToneTO This object contains the default timeout value for dial tone. The MTA MUST NOT update this object with the value provided in the NCS message (if present). If the value of the object is m…	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.6
pktcNcsEndPntConfigMessageWaitingTO This object contains the default timeout value for message waiting indicator. The MTA MUST NOT update this object with the value provided in the NCS message (if present). If the value of the object is modified by the…	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.7
pktcNcsEndPntConfigOffHookWarnToneTO This object contains the default timeout value for the off hook Warning tone. The MTA MUST NOT update this object with the value provided in the NCS message (if present). If the value of the object is modified by the…	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.8
pktcNcsEndPntConfigRingingTO This object contains the default timeout value for ringing. The MTA MUST NOT update this object with the value provided in the NCS message (if present). If the value of the object is modified by the SNMP Management …	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.9
pktcNcsEndPntConfigRingBackTO This object contains the default timeout value for ring back. The MTA MUST NOT update this object with the value provided in the NCS message (if present). If the value of the object is modified by the SNMP Management…	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.10
pktcNcsEndPntConfigReorderToneTO This object contains the default timeout value for reorder tone. The MTA MUST NOT update this object with the value provided in the NCS message (if present). If the value of the object is modified by the SNMP Managem…	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.11
pktcNcsEndPntConfigStutterDialToneTO This object contains the default timeout value for stutter dial tone. The MTA MUST NOT update this object with the value provided in the NCS message (if present). If the value of the object is modified by the SNMP Ma…	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.12
pktcNcsEndPntConfigTSMax This MIB object is used as part of an NCS retransmission algorithm. Prior to any retransmission, the MTA must check to make sure that the time elapsed since the sending of the initial datagram does not exceed t…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.13
pktcNcsEndPntConfigMax1 This object contains the suspicious error threshold for signaling messages. The pktcNcsEndPntConfigMax1 object indicates the retransmission threshold at which the MTA MAY actively query the domain name server (DNS) i…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.14
pktcNcsEndPntConfigMax2 This object contains the disconnect error threshold for signaling messages. The pktcNcsEndPntConfigMax2 object indicates the retransmission threshold at which the MTA SHOULD contact the DNS one more time to see if an…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.15
pktcNcsEndPntConfigMax1QEnable This object enables/disables the Max1 domain name server (DNS) query operation when the pktcNcsEndPntConfigMax1 threshold has been reached.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7432.2.1.2.1.1.16
pktcNcsEndPntConfigMax2QEnable This object enables/disables the Max2 domain name server (DNS) query operation when the pktcNcsEndPntConfigMax2 threshold has been reached.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7432.2.1.2.1.1.17
pktcNcsEndPntConfigMWD Maximum Waiting Delay (MWD) contains the maximum number of seconds an MTA waits after powering on, before initiating the restart procedure with the call agent.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.18
pktcNcsEndPntConfigTdinit This MIB object represents the 'disconnected' initial waiting delay within the context of an MTA's 'disconnected procedure'. The 'disconnected procedure' is initiated when an endpoint becomes 'disconnected' wh…	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.19
pktcNcsEndPntConfigTdmin This MIB object represents the 'disconnected' minimum waiting delay within the context of an MTA's 'disconnected procedure', specifically when local user activity is detected. The 'disconnected procedure' is i…	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.20
pktcNcsEndPntConfigTdmax This object contains the maximum number of seconds the MTA waits after a disconnect, before initiating the disconnected procedure with the call agent.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.21
pktcNcsEndPntConfigRtoMax This object specifies the maximum number of seconds the MTA waits for a response to an NCS message before initiating a retransmission.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.22
pktcNcsEndPntConfigRtoInit This object contains the initial number of seconds for the retransmission timer.	millisecondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.23
pktcNcsEndPntConfigLongDurationKeepAlive Specifies a timeout value in minutes for sending long duration call notification message.	minutesSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.24
pktcNcsEndPntConfigThist Timeout period in seconds before no response is declared.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7432.2.1.2.1.1.25
pktcNcsEndPntConfigStatus This object contains the Row Status associated with the pktcNcsEndPntConfigTable. There are no restrictions or dependencies amidst the columnar objects before this row can be activated or for modifications of the …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7432.2.1.2.1.1.26
pktcNcsEndPntConfigCallWaitingMaxRep This object contains the default value of the maximum number of repetitions of the call waiting tone that the MTA will play from a single CMS request. The MTA MUST NOT update this object with the information provided…	Unsigned32r/w Constraints: range: 0-10	.1.3.6.1.4.1.7432.2.1.2.1.1.27
pktcNcsEndPntConfigCallWaitingDelay This object contains the delay between repetitions of the call waiting tone that the MTA will play from a single CMS request.	secondsUnsigned32r/w Constraints: range: 1-100	.1.3.6.1.4.1.7432.2.1.2.1.1.28
pktcNcsEndPntStatusCallIpAddressType This object contains the type of Internet address of the CMS currently being used for this endpoint.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.7432.2.1.2.1.1.29
pktcNcsEndPntStatusCallIpAddress This object contains the Internet address of the CMS currently being used for this endpoint. This Internet address is used to create the appropriate security association. The type of this IP address is determined by …	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.7432.2.1.2.1.1.30
pktcNcsEndPntStatusError This object contains the error status for this interface. The operational status indicates that all operations necessary to put the line in service have occurred, and the CMS has acknowledged the Restart In Progress …	Enumeration Enumerated Values: 1 operational 2 noSecurityAssociation 3 disconnected	.1.3.6.1.4.1.7432.2.1.2.1.1.31
pktcNcsEndPntConfigMinHookFlash This is the minimum time a line needs to be on hook for a valid hook flash. The value of this object MUST be greater than the value of pktcNcsEndPntConfigPulseDialMaxBreakTime. The value of pktcNcsEndPntConfigMinHoo…	MillisecondsUnsigned32r/w Constraints: range: 20-1550	.1.3.6.1.4.1.7432.2.1.2.1.1.32
pktcNcsEndPntConfigMaxHookFlash This is the maximum time a line needs to be on hook for a valid hook flash. The value of pktcNcsEndPntConfigMaxHookFlash MUST be greater than pktcNcsEndPntConfigMinHookFlash. This object MUST only be …	MillisecondsUnsigned32r/w Constraints: range: 20-1550	.1.3.6.1.4.1.7432.2.1.2.1.1.33
pktcNcsEndPntConfigPulseDialInterdigitTime This is the pulse dial inter-digit timeout. This object MUST only be set via the configuration file during the provisioning process.	MillisecondsUnsigned32r/w Constraints: range: 100-1500	.1.3.6.1.4.1.7432.2.1.2.1.1.34
pktcNcsEndPntConfigPulseDialMinMakeTime This is the minimum make pulse width for the dial pulse. The value of pktcNcsEndPntConfigPulseDialMinMakeTime MUST be less than pktcNcsEndPntConfigPulseDialMaxMakeTime. This object MUST only be set via the configurat…	MillisecondsUnsigned32r/w Constraints: range: 20-200	.1.3.6.1.4.1.7432.2.1.2.1.1.35
pktcNcsEndPntConfigPulseDialMaxMakeTime This is the maximum make pulse width for the dial pulse. The value of pktcNcsEndPntConfigPulseDialMaxMakeTime MUST be greater than pktcNcsEndPntConfigPulseDialMinMakeTime. This object MUST only be provided via the co…	MillisecondsUnsigned32r/w Constraints: range: 20-200	.1.3.6.1.4.1.7432.2.1.2.1.1.36
pktcNcsEndPntConfigPulseDialMinBreakTime This is the minimum break pulse width for the dial pulse. The value of pktcNcsEndPntConfigPulseDialMinBreakTime MUST be less than pktcNcsEndPntConfigPulseDialMaxBreakTime. This object must only be provided via the co…	MillisecondsUnsigned32r/w Constraints: range: 20-200	.1.3.6.1.4.1.7432.2.1.2.1.1.37
pktcNcsEndPntConfigPulseDialMaxBreakTime This is the maximum break pulse width for the dial pulse. The value of pktcNcsEndPntConfigPulseDialMaxBreakTime MUST be greater than pktcNcsEndPntConfigPulseDialMinBreakTime. This object MUST only be provided via the…	MillisecondsUnsigned32r/w Constraints: range: 20-200	.1.3.6.1.4.1.7432.2.1.2.1.1.38