CISCO-ALPS-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
12
Rows
12
Columns
153

alpsRemPeerTable

table deprecated
.1.3.6.1.4.1.9.9.95.1.2.2 · 1 row entry · 18 columns
Open in standard view 
A list of Remote peers that the local ALPS peer can communicate
with.
alpsRemPeerEntry entry .1.3.6.1.4.1.9.9.95.1.2.2.1
Each entry represents an Remote ALPS Peer.
Indexes
alpsRemPeerIpAddr
Column Syntax OID
alpsRemPeerIpAddr deprecated
The remote IP address for the TCP Connection.
SNMPv2-SMIIpAddress
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.9.9.95.1.2.2.1.1
alpsRemPeerConnType deprecated
Type of ALPS circuit established. Dynamic circuits are
established only when there is data traffic that needs to be
sent across and are closed when the alpsRemPeerIdleTimer
expires. Permanent circuits stay up regardle…
Enumerationr/w
Enumerated Values:
1permanent
2dynamic
 .1.3.6.1.4.1.9.9.95.1.2.2.1.2
alpsRemPeerLocalPort deprecated
The port number used locally by the tcp connection for the
circuit. the initiator of a connection will dynamically assign
a port number. the other end of the connection will have a
well-known port number applicable to t…
Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.9.9.95.1.2.2.1.3
alpsRemPeerRemotePort deprecated
The port number used by the remote end of the tcp connection
for the circuit. the initiator of a connection will
dynamically assign a port number. the other end of the
connection will have a well-known port number appli…
Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.9.9.95.1.2.2.1.4
alpsRemPeerState deprecated
TCP Peer State. Initially the connection is in the closed state.
For permanent connections, it starts opening the TCP connection
immediately, but for dynamic ones, it waits till there is traffic
addressed to the remote …
Enumeration
Enumerated Values:
1closed
2opening
3opened
 .1.3.6.1.4.1.9.9.95.1.2.2.1.5
alpsRemPeerUptime deprecated
Time elapsed since TCP connection was established.
SNMPv2-SMITimeTicks
Textual Convention: SNMPv2-SMITimeTicks Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.2.2.1.6
alpsRemPeerNumActiveCkts deprecated
Number of active ALPS circuits in this TCP session.
SNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.2.2.1.7
alpsRemPeerIdleTimer deprecated
The TCP session with the peer will be closed if there is no
activity for alpsInactiveTimer seconds. This is valid only
for dynamic circuits
SNMPv2-TCTimeIntervalr/w
Textual Convention: SNMPv2-TCTimeInterval Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.9.95.1.2.2.1.8
alpsRemPeerAlarmsEnabled deprecated
Specifies whether alarms are generated for this remote Peer
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.95.1.2.2.1.9
alpsRemPeerTCPQlen deprecated
Maximum TCP Queue size allowed for this TCP session.
packetsInteger32r/w
Constraints:
range: 1-200
 .1.3.6.1.4.1.9.9.95.1.2.2.1.10
alpsRemPeerOutPackets deprecated
Number of packets transmitted to the remote peer.
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.2.2.1.11
alpsRemPeerOutOctets deprecated
Number of octets transmitted to the remote peer.
octetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.2.2.1.12
alpsRemPeerInPackets deprecated
Number of packets received from the remote peer.
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.2.2.1.13
alpsRemPeerInOctets deprecated
Number of octets received from the remote peer.
octetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.2.2.1.14
alpsRemPeerDropsGiant deprecated
Number of Packets dropped because they were larger than the
maximum allowed packet size of 3840 bytes.
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.2.2.1.15
alpsRemPeerDropsQFull deprecated
Number of packets dropped because the TCP queue (of
size alpsRemPeerTCPQlen) was full.
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.2.2.1.16
alpsRemPeerDropsPeerUnreach deprecated
Number of packets dropped because remote peer was unreachable.
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.2.2.1.17
alpsRemPeerRowStatus deprecated
This object is used to create a new row or modify or
delete an existing row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.95.1.2.2.1.18

alpsRemPeerCfgTable

table
.1.3.6.1.4.1.9.9.95.1.2.3 · 1 row entry · 10 columns
Open in standard view 
Table listing of all administered ALPS remote peer
configuration entries on this node.  Entries in  
this table can be created via a CLI command or via 
alpsRemPeerCfgRowStatus.
alpsRemPeerCfgEntry entry .1.3.6.1.4.1.9.9.95.1.2.3.1
Each entry represents an ALPS remote peer
configuration entry on this node.
Indexes
alpsRemPeerCfgIpAddr alpsRemPeerCfgProtocol
Column Syntax OID
alpsRemPeerCfgIpAddr
The configured IP address of an ALPS remote peer.
SNMPv2-SMIIpAddress
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.9.9.95.1.2.3.1.1
alpsRemPeerCfgProtocol
The configured ALPS protocol encapsulation. This
protocol encapsulation is at the layer above TCP.
Enumeration
Enumerated Values:
1atp
2matipTypeA
 .1.3.6.1.4.1.9.9.95.1.2.3.1.2
alpsRemPeerCfgActivation
The configured type of ALPS peer activation.
Enumerationr/w
Enumerated Values:
1permanent
2dynamic
 .1.3.6.1.4.1.9.9.95.1.2.3.1.3
alpsRemPeerCfgTCPQLen
The configured maximum TCP Queue size.
packetsInteger32r/w
Constraints:
range: 1-100
 .1.3.6.1.4.1.9.9.95.1.2.3.1.4
alpsRemPeerCfgIdleTimer
The configured idle timer for a dynamic
activation peer.
SNMPv2-TCTimeIntervalr/w
Textual Convention: SNMPv2-TCTimeInterval Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.9.95.1.2.3.1.5
alpsRemPeerCfgNoCircTimer
The configured no-circuit timer for a dynamic
activation peer.
SNMPv2-TCTimeIntervalr/w
Textual Convention: SNMPv2-TCTimeInterval Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.9.95.1.2.3.1.6
alpsRemPeerCfgAlarmsOn
The configured parameter which specifies whether
alarms are generated for remote peer connections
to the IP address in alpsRemPeerCfgIpAddr.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.95.1.2.3.1.7
alpsRemPeerCfgStatIntvl
The configured status interval timer.
SNMPv2-TCTimeIntervalr/w
Textual Convention: SNMPv2-TCTimeInterval Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.9.95.1.2.3.1.8
alpsRemPeerCfgStatRetry
The configured number of status retries.
Integer32r/w
Constraints:
range: 0-100
 .1.3.6.1.4.1.9.9.95.1.2.3.1.9
alpsRemPeerCfgRowStatus
This object is used to create a new row or modify or
delete an existing row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.95.1.2.3.1.10

alpsRemPeerConnTable

table
.1.3.6.1.4.1.9.9.95.1.2.4 · 1 row entry · 27 columns
Open in standard view 
Table listing of all ALPS remote peer
connections on this node.
alpsRemPeerConnEntry entry .1.3.6.1.4.1.9.9.95.1.2.4.1
Each entry represents an ALPS remote peer
connection on this node.
Indexes
alpsRemPeerConnIpAddr alpsRemPeerConnIdString
Column Syntax OID
alpsRemPeerConnIpAddr
The IP address of the ALPS remote peer.
SNMPv2-SMIIpAddress
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.9.9.95.1.2.4.1.1
alpsRemPeerConnIdString
A descriptive ASCII string that is used to distinguish
among different peer connections to the same ALPS remote
peer IP address.
OctetString
Constraints:
range: 1-20
 .1.3.6.1.4.1.9.9.95.1.2.4.1.2
alpsRemPeerConnLocalPort
The local TCP port number used by the underlying
TCP connection to an ALPS remote peer.
Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.9.9.95.1.2.4.1.3
alpsRemPeerConnForeignPort
The foreign (remote) TCP port number used by the
underlying TCP connection to an ALPS remote peer.
Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.9.9.95.1.2.4.1.4
alpsRemPeerConnState
The state of the connection to an ALPS remote peer.
Enumeration
Enumerated Values:
1closed
2opening
3opened
4busy
 .1.3.6.1.4.1.9.9.95.1.2.4.1.5
alpsRemPeerConnProtocol
The ALPS protocol encapsulation used on the
connection to the ALPS remote peer. This protocol
encapsulation is a layer above TCP.
Enumeration
Enumerated Values:
1atp
2matipTypeA
 .1.3.6.1.4.1.9.9.95.1.2.4.1.6
alpsRemPeerConnCreation
The stimulus for creating the peer connection object.
The peer connection object may be created solely due to
configuration (admin) or due to a combination of
configuration and protocol events (learned).
Enumeration
Enumerated Values:
1admin
2learned
 .1.3.6.1.4.1.9.9.95.1.2.4.1.7
alpsRemPeerConnActivation
Basis for activation a peer connection. A permanent activation peer
connection will attempt to open immediately and stay open, regardless
of the usage of the peer connection. A dynamic activation peer
connection only…
Enumeration
Enumerated Values:
1permanent
2dynamic
 .1.3.6.1.4.1.9.9.95.1.2.4.1.8
alpsRemPeerConnUptime
Elapsed time since the ALPS peer connection
was successfully established.
SNMPv2-SMITimeTicks
Textual Convention: SNMPv2-SMITimeTicks Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.2.4.1.9
alpsRemPeerConnNumActCirc
The number of ALPS virtual circuits using the
connection to this ALPS remote peer.
Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.9.9.95.1.2.4.1.10
alpsRemPeerConnLastTxRx
The value of sysUpTime when a peer data message
was last transmitted or received across this
ALPS remote peer connection. This timestamp is not
update if the peer message is a peer status
inquiry/response message.
SNMPv2-TCTimeStamp
Textual Convention: SNMPv2-TCTimeStamp Unsigned32
 .1.3.6.1.4.1.9.9.95.1.2.4.1.11
alpsRemPeerConnLastRxAny
The value of sysUpTime when a peer data or
status message is last received across the
ALPS remote peer connection.
SNMPv2-TCTimeStamp
Textual Convention: SNMPv2-TCTimeStamp Unsigned32
 .1.3.6.1.4.1.9.9.95.1.2.4.1.12
alpsRemPeerConnIdleTimer
A dynamic activation ALPS peer connection will be closed
if zero peer data messages are sent or received for
a length of time greater than or equal to this timer.
SNMPv2-TCTimeInterval
Textual Convention: SNMPv2-TCTimeInterval Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.9.95.1.2.4.1.13
alpsRemPeerConnNoCircTimer
A dynamic activation ALPS peer connection will be closed
if zero ALPS circuits are active or attempt to activate
for a length of time greater than or equal to this timer.
SNMPv2-TCTimeInterval
Textual Convention: SNMPv2-TCTimeInterval Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.9.95.1.2.4.1.14
alpsRemPeerConnTCPQLen
The maximum number of ALPS peer messages that
can be queued in a single TCP session.
Integer32
Constraints:
range: 1-100
 .1.3.6.1.4.1.9.9.95.1.2.4.1.15
alpsRemPeerConnAlarmsOn
This parameter specifies whether ALPS alarms
are generated for this ALPS remote peer connection.
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.95.1.2.4.1.16
alpsRemPeerConnStatIntvl
The time interval (in seconds) between transmission of
consecutive ALPS Peer Status messages. These messages
are only transmitted if zero messages are received on the
peer connection for a length of time greater than…
Integer32
Constraints:
range: 0-300
 .1.3.6.1.4.1.9.9.95.1.2.4.1.17
alpsRemPeerConnStatRetry
The number of consecutive unanswered ALPS Peer Status
messages transmitted before closing the conenction to
the ALPS remote peer.
Integer32
Constraints:
range: 0-100
 .1.3.6.1.4.1.9.9.95.1.2.4.1.18
alpsRemPeerConnDownReason
Reason that an ALPS Peer connection failed to
open sauccessfully.
Enumeration
Enumerated Values:
1unknown
2idle
3noCircuits
4destUnreachable
5foreignReset
6localReset
7noMemory
8openingTimeout
 .1.3.6.1.4.1.9.9.95.1.2.4.1.19
alpsRemPeerConnOutPackets
Number of packets transmitted on this ALPS
remote peer connection.
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.2.4.1.20
alpsRemPeerConnOutOctets
Number of octets transmitted on this ALPS
remote peer connection.
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.2.4.1.21
alpsRemPeerConnInPackets
Number of packets received on this ALPS
remote peer connection.
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.2.4.1.22
alpsRemPeerConnInOctets
Number of octets received on this ALPS
remote peer connection.
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.2.4.1.23
alpsRemPeerConnDropsGiant
Number of ALPS peer packets dropped due to exceeding
the maximum allowed packet size of 3840 bytes.
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.2.4.1.24
alpsRemPeerConnDropsQFull
Number of ALPS peer packets dropped because
the TCP output queue is full.
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.2.4.1.25
alpsRemPeerConnDropsUnreach
Number of ALPS peer packets dropped because
the ALPS remote peer is unreachable.
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.2.4.1.26
alpsRemPeerConnDropsVersion
Number of ALPS peer packets dropped because
of a version mismatch in the ALPS encapsulation.
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.2.4.1.27

alpsCktBaseTable

table
.1.3.6.1.4.1.9.9.95.1.3.1 · 1 row entry · 24 columns
Open in standard view 
A list of ALPS circuits. This table contains variables
common to central & remote routers.
alpsCktBaseEntry entry .1.3.6.1.4.1.9.9.95.1.3.1.1
Details of ALPS Circuits.
Indexes
alpsCktBaseName alpsCktBaseDlcType
Column Syntax OID
alpsCktBaseName
Specifies the ALPS Circuit Name. This is unique within the
network.
AlpsCktName
Textual Convention: AlpsCktName OctetString
Type Constraints:
range: 1..12
 .1.3.6.1.4.1.9.9.95.1.3.1.1.1
alpsCktBaseDlcType
Specifies what type of circuit this is. The X25 circuit is set up
with the same name as the P1024 circuit so we need this
variable to distinguish between the two, in case local switching
is done.
Enumeration
Enumerated Values:
1emtox
2ax25
3alc
4uts
 .1.3.6.1.4.1.9.9.95.1.3.1.1.2
alpsCktBasePriPeerAddr
This is the IP address of the Primary Central peer. It is
mandatory to configure a primary peer, but the backup peer is
optional.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.9.9.95.1.3.1.1.3
alpsCktBaseAlarmsEnabled
Specifies whether alarms are generated for this ALPS circuit.
Alarms can be syslog messages or SNMP traps - both are controlled
using the same flags.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.95.1.3.1.1.4
alpsCktBaseConnType
Specifies the ALPS Circuit Connection Type.
Enumerationr/w
Enumerated Values:
1permanent
2dynamic
 .1.3.6.1.4.1.9.9.95.1.3.1.1.5
alpsCktBaseState
Indicates the state of ALPS Circuit.
Enumeration
Enumerated Values:
1disabled
2inoperable
3opening
4opened
5cktBusy
6peerBusy
7updating
 .1.3.6.1.4.1.9.9.95.1.3.1.1.6
alpsCktBaseNumActiveAscus
Reports the number of enabled ASCUs that are attached to
this ALPS Circuit. Attachment of an ASCU to an ALPS circuit
may occur due to configuration or due to information passed
in a protocol message.
Integer32
Constraints:
range: 0-64
 .1.3.6.1.4.1.9.9.95.1.3.1.1.7
alpsCktBaseCurrentPeer
Reports the IP address of the peer that this ALPS circuit
is currently connected to.
SNMPv2-SMIIpAddress
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.9.9.95.1.3.1.1.8
alpsCktBaseLifeTimeTimer
A data message that has been queued within the router for
longer than this interval will be dropped.
SNMPv2-TCTimeIntervalr/w
Textual Convention: SNMPv2-TCTimeInterval Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.9.95.1.3.1.1.9
alpsCktBaseHostLinkNumber
Specifies host link number (on Central router) for this ALPS
Circuit. The host link number is used to provide a
degree of transparency to the remote router. A single host link
may correspond to multiple physical links …
Integer32r/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.9.9.95.1.3.1.1.10
alpsCktBaseHostLinkType
Specifies host link type(on Central router) for this
ALPS Circuit.
Enumerationr/w
Enumerated Values:
1ax25
2emtox
 .1.3.6.1.4.1.9.9.95.1.3.1.1.11
alpsCktBaseRemHld
Specifies the HLD (High-level descriptor) of the AX.25/EMTOX
host for this ALPS Circuit. This serves as an identifier
for the host
Integer32r/w
Constraints:
range: 1-32639
 .1.3.6.1.4.1.9.9.95.1.3.1.1.12
alpsCktBaseLocalHld
Specifies the local HLD for this ALPS Circuit. HLDs are required
at the host for both ends of the connection.
Integer32r/w
Constraints:
range: 1-32639
 .1.3.6.1.4.1.9.9.95.1.3.1.1.13
alpsCktBaseDownReason
Reports the reason why this ALPS Circuit is down, if it is down.
Enumeration
Enumerated Values:
1unknown
2noReason
3hostLinkDown
4cktDisabled
5hostLinkDisabled
6noHostLinkMatched
7noHldMatched
8cktNameInUse
9pvcLcnOutOfRange
10x25ParamInvalid
11cktOpeningTimeout
12x25ClearDteNoReason
13configMismatch
14noResourcesAvail
15incompatibleA1A2
16cktIdle
17peerDown
18noAscusConfigured
19x25ClearHostUnknown
20x25ClearHostDown
21x25ClearHostDisabled
22x25ClearHostSaturated
23x25ClearCallerUnknown
24x25ClearCallerUnauth
25x25ClearConfigRejected
26x25ClearConfigFallback
27x25ClearConfigIncompat
28x25ClearHLDUnknown
29x25ClearPIDUnknown
30x25ClearFacilRejected
31x25ClearNetNoReason
32pvcLcnInUse
33noSvcLcnAvail
34peerIdle
35presUnknown
36presMismatch
37openMsgTooShort
38mpxUnknown
39mpxHdrMismatch
40trafTypeMismatch
41codingMismatch
42ascuInSession
 .1.3.6.1.4.1.9.9.95.1.3.1.1.14
alpsCktBaseOutPackets
Number of packets transmitted to remote peer over this circuit.
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.3.1.1.15
alpsCktBaseOutOctets
Number of octets transmitted to remote peer over this circuit.
octetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.3.1.1.16
alpsCktBaseInPackets
Number of packets received from remote peer over this circuit.
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.3.1.1.17
alpsCktBaseInOctets
Number of octets received from remote peer over this circuit.
octetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.3.1.1.18
alpsCktBaseDropsCktDisabled
Number of packets dropped because the circuit was disabled. This
would typically be packets that were queueued before the circuit was
disabled which are now left in the queue.
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.3.1.1.19
alpsCktBaseDropsQOverflow
Number of packets dropped due to TCP Congestion.
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.3.1.1.20
alpsCktBaseDropsLifeTimeExpd
Number of packets which were queued within the router for
longer than alpsCktBaseLifeTimeTimer.
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.3.1.1.21
alpsCktBaseEnabled
This specifies if the circuit has been enabled. After a circuit
has been configured, it must be explicitly enabled in order for
the circuit to be set up.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.95.1.3.1.1.22
alpsCktBaseRowStatus
This object is used to create a new row or modify or
delete an existing row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.95.1.3.1.1.23
alpsCktBaseCurrPeerConnId
A descriptive ASCII string that is used to distinguish
among different peer connections to the same ALPS remote
peer IP address.
OctetString
Constraints:
range: 1-20
 .1.3.6.1.4.1.9.9.95.1.3.1.1.24

alpsCktX25Table

table
.1.3.6.1.4.1.9.9.95.1.3.2 · 1 row entry · 6 columns
Open in standard view 
A list of ALPS X.25 circuits. These entries exist only for X.25
circuits. hence this table would probably be empty at the remote 
router
alpsCktX25Entry entry .1.3.6.1.4.1.9.9.95.1.3.2.1
Details of ALPS Circuits.
Indexes
alpsCktBaseName alpsCktX25DlcType
Column Syntax OID
alpsCktX25DlcType
Specifies what type of circuit this is.
Enumeration
Enumerated Values:
1emtox
2ax25
 .1.3.6.1.4.1.9.9.95.1.3.2.1.1
alpsCktX25IfIndex
Reports the interface the circuit is on. This is the interface
which is connected to the host
IF-MIBInterfaceIndex
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
 .1.3.6.1.4.1.9.9.95.1.3.2.1.2
alpsCktX25LCN
The Logical Channel Number being used on the X.25 VC for
this ALPS Circuit.
Integer32
Constraints:
range: 1-4096
 .1.3.6.1.4.1.9.9.95.1.3.2.1.3
alpsCktX25HostX121
The X.121 address on the host side which the central router uses to
connect to the host
RFC1382-MIBX121Address
Textual Convention: RFC1382-MIBX121Address OctetString
Type Constraints:
range: 0..17
 .1.3.6.1.4.1.9.9.95.1.3.2.1.4
alpsCktX25RemoteX121
X.121 address of the remote side. Remote here refers to
the side that the ASCUS are connected to and is also
referred to as the remote router.
RFC1382-MIBX121Address
Textual Convention: RFC1382-MIBX121Address OctetString
Type Constraints:
range: 0..17
 .1.3.6.1.4.1.9.9.95.1.3.2.1.5
alpsCktX25DropsVcReset
Number of packets dropped due to the VC being reset. These are
packets that were queued up for transmission on that VC when it
was reset
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.3.2.1.6

alpsCktP1024Table

table
.1.3.6.1.4.1.9.9.95.1.3.3 · 1 row entry · 15 columns
Open in standard view 
A list of ALC or UTS  Alps circuits.
alpsCktP1024Entry entry .1.3.6.1.4.1.9.9.95.1.3.3.1
Details of ALPS Circuits.
Indexes
alpsCktBaseName alpsCktP1024DlcType
Column Syntax OID
alpsCktP1024DlcType
Specifies what type of circuit this is.
Enumeration
Enumerated Values:
3alc
4uts
 .1.3.6.1.4.1.9.9.95.1.3.3.1.1
alpsCktP1024BackupPeerAddr
This is the IP address of the backup remote peer. This is optional
and hence may not always exist.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.9.9.95.1.3.3.1.2
alpsCktP1024RetryTimer
Specifies the interval at which a permanent ALPS circuit
will attempt to reestablish the circuit in case it wasn't
able to come up.
SNMPv2-TCTimeIntervalr/w
Textual Convention: SNMPv2-TCTimeInterval Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.9.95.1.3.3.1.3
alpsCktP1024IdleTimer
If there is no traffic on a dynamic ALPS circuit for this
interval, it will be cleared.
SNMPv2-TCTimeIntervalr/w
Textual Convention: SNMPv2-TCTimeInterval Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.9.95.1.3.3.1.4
alpsCktP1024EmtoxX121
Specifies the X.121 address of the SVC established with
EMTOX host. This field should be set to length zero in
the case of PVCs (AX.25 host).
RFC1382-MIBX121Addressr/w
Textual Convention: RFC1382-MIBX121Address OctetString
Type Constraints:
range: 0..17
 .1.3.6.1.4.1.9.9.95.1.3.3.1.5
alpsCktP1024Ax25LCN
Specifies the Logical Channel Number being used on the PVC
established with AX.25 host. This field should be set to zero in
the case of SVCs (EMTOX host).
Integer32r/w
Constraints:
range: 0-4096
 .1.3.6.1.4.1.9.9.95.1.3.3.1.6
alpsCktP1024WinOut
Specifies X.25 transmit Window size on the Logical Channel
Number of this ALPS Circuit.
Integer32r/w
Constraints:
range: 1-7
 .1.3.6.1.4.1.9.9.95.1.3.3.1.7
alpsCktP1024WinIn
Specifies the X.25 receive Window size on the Logical Channel
Number of this ALPS Circuit.
Integer32r/w
Constraints:
range: 1-7
 .1.3.6.1.4.1.9.9.95.1.3.3.1.8
alpsCktP1024OutPktSize
Specifies the X.25 maxiumum output Packet size on the Logical
Channel Number of this ALPS Circuit. The default output Packet size
for AX.25 is 240 bytes and 128 bytes for EMTOX.
bytesInteger32r/w
Constraints:
range: 128-4096
 .1.3.6.1.4.1.9.9.95.1.3.3.1.9
alpsCktP1024InPktSize
Specifies X.25 maximum input Packet size on the Logical Channel
Number of this ALPS Circuit. The default input Packet size for
AX.25 is 240 bytes and 128 bytes for EMTOX.
bytesInteger32r/w
Constraints:
range: 128-4096
 .1.3.6.1.4.1.9.9.95.1.3.3.1.10
alpsCktP1024SvcMsgList
Specifies the Service Message List Number to use on this
ALPS Circuit. This allows custom service messages to be sent
for ASCUs on a particular circuit. Service messages are sent out
by the router to the ASCU when abno…
Integer32r/w
Constraints:
range: 0-8
 .1.3.6.1.4.1.9.9.95.1.3.3.1.11
alpsCktP1024SvcMsgIntvl
Specifies Service Message Time Interval for the Service
messages to be sent this ALPS Circuit. This controls how
frequently the messages are repeated when an error condition
(e.g. network being down) persists.
SNMPv2-SMITimeTicksr/w
Textual Convention: SNMPv2-SMITimeTicks Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.3.3.1.12
alpsCktP1024DropsUnkAscu
Number of packets that were found to be from an Unknown ASCU
(i.e. an ASCU that had not been configured) and hence were dropped.
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.3.3.1.13
alpsCktP1024RowStatus
This object is used to create a new row or modify or
delete an existing row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.95.1.3.3.1.14
alpsCktP1024MatipCloseDelay
Specifies the minumum delay between transmission of a MATIP
Close and the transmission of a MATIP Session Open for
this ALPS circuit.
SNMPv2-TCTimeIntervalr/w
Textual Convention: SNMPv2-TCTimeInterval Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.9.95.1.3.3.1.15

alpsCktAscuTable

table
.1.3.6.1.4.1.9.9.95.1.3.4 · 1 row entry · 7 columns
Open in standard view 
A list of ASCUs for each ALPS Circuit. This may not include all
ASCUs which have this circuit configured as alpsAscuCktName because
some ASCUs may be rejected by the host while setting up the circuit.
alpsCktAscuEntry entry .1.3.6.1.4.1.9.9.95.1.3.4.1
Details of ASCUs on ASCU Circuits.
Indexes
alpsCktAscuCktName alpsCktAscuCktDlcType alpsCktAscuA1 alpsCktAscuA2
Column Syntax OID
alpsCktAscuCktName
The name of the ALPS circuit which this ASCU is on. The
circuit may be always up (for permanent circuits) or get set up
(dynamic circuits) when there is traffic on one of the ASCUs which
are set up for that circuit.
AlpsCktName
Textual Convention: AlpsCktName OctetString
Type Constraints:
range: 1..12
 .1.3.6.1.4.1.9.9.95.1.3.4.1.1
alpsCktAscuCktDlcType
Specifies what type of circuit this is. The X.25 circuit is set up
with the same name as the ALC circuit so we need this
variable to distinguish between the two.
Enumeration
Enumerated Values:
1emtox
2ax25
3alc
4uts
 .1.3.6.1.4.1.9.9.95.1.3.4.1.2
alpsCktAscuA1
A1 value. This is used along with the alpsCktAscuA2 value to
identify the ASCU within the circuit.
AlpsAscuA1A2Value
Textual Convention: AlpsAscuA1A2Value Integer32
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.95.1.3.4.1.3
alpsCktAscuA2
A2 value. This is used along with the alpsCktAscuA1 value to
identify the ASCU within the circuit.
AlpsAscuA1A2Value
Textual Convention: AlpsAscuA1A2Value Integer32
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.95.1.3.4.1.4
alpsCktAscuIfIndex
Reports the interface the ASCU is on. This field, along with
alpsCktAscuId is provided so that it is possible to correlate this
information with the configured ASCU information in alpsAscuTable
IF-MIBInterfaceIndex
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
 .1.3.6.1.4.1.9.9.95.1.3.4.1.5
alpsCktAscuId
Reports the ASCU Identifier which uniquely
identifies an ASCU on a given interface. This value is
the Interface Address (IA) for ALC and the Remote Identifier
(RID) for UTS. A value of 0 indicates that the ASCU id is ei…
Integer32
Constraints:
range: 0-127
 .1.3.6.1.4.1.9.9.95.1.3.4.1.6
alpsCktAscuStatus
Reports the ASCU status - ASCUs configured on the circuit
can be rejected at the host and would then be marked REJECT. Also,
ASCUs configured after the circuit has been established are not added
dynamically to the circ…
Enumeration
Enumerated Values:
1unknown
2ok
3reject
4new
5pending
 .1.3.6.1.4.1.9.9.95.1.3.4.1.7

alpsIfP1024Table

table
.1.3.6.1.4.1.9.9.95.1.4.1 · 1 row entry · 13 columns
Open in standard view 
A list of interfaces running the P1024B or P1024C protocols
alpsIfP1024Entry entry .1.3.6.1.4.1.9.9.95.1.4.1.1
Interface Details
Indexes
IF-MIBifIndex
Column Syntax OID
alpsIfP1024EncapType
Reports the encapsulation type for this Serial Interface.
Enumeration
Enumerated Values:
1alc
2uts
 .1.3.6.1.4.1.9.9.95.1.4.1.1.1
alpsIfP1024PollRespTimeout
Specifies the Poll Response Time out value.
SNMPv2-TCTimeIntervalr/w
Textual Convention: SNMPv2-TCTimeInterval Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.9.95.1.4.1.1.2
alpsIfP1024GATimeout
Specifies the time-out delay between receipt of first character
of an input sequence solicited by a poll and receipt of GA
sequence.
SNMPv2-TCTimeIntervalr/w
Textual Convention: SNMPv2-TCTimeInterval Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.9.95.1.4.1.1.3
alpsIfP1024PollPauseTimeout
Specifies the minimum delay between two poll cycles. Thus
the poll pause interval is counted from the instant when the first
ASCU in the poll list is polled. Note that this is the delay between
two traversals of the en…
SNMPv2-TCTimeIntervalr/w
Textual Convention: SNMPv2-TCTimeInterval Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.9.95.1.4.1.1.4
alpsIfP1024MaxErrCnt
Specifies a maximum error count for this interface. After
an ASCU link comes up, if it experiences this number of errors the
ASCU link will be shutdown. The default value of 0 results in the
ASCU link never being shutdo…
Integer32r/w
Constraints:
range: 0-30
 .1.3.6.1.4.1.9.9.95.1.4.1.1.5
alpsIfP1024MaxRetrans
Specifies the maximum number of times an output message will
be retransmitted before it is discarded. This is relevant only
for P1024C (UTS). For ALC, a value of 0 will be returned. Note that
legal values for UTS are 1-…
Integer32r/w
Constraints:
range: 0-10
 .1.3.6.1.4.1.9.9.95.1.4.1.1.6
alpsIfP1024CurrErrCnt
Reports the number of errors currently existing for this
ASCU link. When this equals alpsIfP1024MaxErrCnt then the
ASCU link will be shut down, unless alpsIfP1024MaxErrCnt
equals 0 in which case the ascu link is never s…
Integer32
Constraints:
range: 0-30
 .1.3.6.1.4.1.9.9.95.1.4.1.1.7
alpsIfP1024MinGoodPollResp
Specifies the number of good Poll Responses to be received
from an ASCU before it can be declared up.
Integer32r/w
Constraints:
range: 1-30
 .1.3.6.1.4.1.9.9.95.1.4.1.1.8
alpsIfP1024PollingRatio
Specifies how many times ASCUs in UP state are polled before
an ASCU in DOWN state is polled again.
Integer32r/w
Constraints:
range: 1-30
 .1.3.6.1.4.1.9.9.95.1.4.1.1.9
alpsIfP1024NumAscus
Reports the number of ASCUs configured on this Serial Port.
AscusSNMPv2-SMIGauge32
Textual Convention: SNMPv2-SMIGauge32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.4.1.1.10
alpsIfP1024ServMsgFormat
Specifies the format of the service message sent to an ASCU
on this interface.
Enumerationr/w
Enumerated Values:
1sita
2apollo
 .1.3.6.1.4.1.9.9.95.1.4.1.1.11
alpsIfP1024ServMsgStatusChange
Specifies whether service messages generated due
to an ALPS circuit status change or an ASCU status change,
will be forwarded to the ASCU.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.95.1.4.1.1.12
alpsIfP1024ServMsgDropTermAddr
Specifies whether the service message will be sent to the same
terminal address of the dropped message or the configured value.
Enumerationr/w
Enumerated Values:
1msgterm
2configterm
 .1.3.6.1.4.1.9.9.95.1.4.1.1.13

alpsIfHLinkTable

table
.1.3.6.1.4.1.9.9.95.1.4.2 · 1 row entry · 6 columns
Open in standard view 
A list of interfaces running AX.25/EMTOX host link protocols.
These are on the central router
alpsIfHLinkEntry entry .1.3.6.1.4.1.9.9.95.1.4.2.1
Details of AX.25/EMTOX host link protocols on an Interface.
Indexes
IF-MIBifIndex alpsIfHLinkHostHld alpsIfHLinkNumber
Column Syntax OID
alpsIfHLinkHostHld
Specifies the HLD of the AX.25/EMTOX host connected on this
Interface. The HLD(High-level descriptor) serves as an
identifier along with the hostlink number and helps correlate the
ALPS circuit to a host link. The hex …
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.9.9.95.1.4.2.1.1
alpsIfHLinkNumber
Specifies the configured Host Link Number on this Serial Interface.
Integer32
Constraints:
range: 1-255
 .1.3.6.1.4.1.9.9.95.1.4.2.1.2
alpsIfHLinkX25ProtocolType
Reports the encapsulation type for this Serial Interface -
AX.25 or EMTOX.
Enumeration
Enumerated Values:
1ax25
2emtox
 .1.3.6.1.4.1.9.9.95.1.4.2.1.3
alpsIfHLinkAx25PvcDamp
The purpose of this object is to handle the link-damping for an
AX.25 host. If the PVC goes inactive (i.e. link goes down, etc...)
for PVCDampValue seconds, then PVC will be destroyed as well as
the associated ALPS cir…
SNMPv2-TCTimeInterval
Textual Convention: SNMPv2-TCTimeInterval Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.9.95.1.4.2.1.4
alpsIfHLinkEmtoxHostX121
Specfies the X.121 address of this EMTOX host.
RFC1382-MIBX121Address
Textual Convention: RFC1382-MIBX121Address OctetString
Type Constraints:
range: 0..17
 .1.3.6.1.4.1.9.9.95.1.4.2.1.5
alpsIfHLinkActiveCkts
Reports the number of ALPS Ckts established with this host.
circuitsInteger32
Constraints:
range: 0-4096
 .1.3.6.1.4.1.9.9.95.1.4.2.1.6

alpsAscuTable

table
.1.3.6.1.4.1.9.9.95.1.5.1 · 1 row entry · 20 columns
Open in standard view 
A list of ALPS ASCUs on an interface. This is defined only at
the remote router.
alpsAscuEntry entry .1.3.6.1.4.1.9.9.95.1.5.1.1
Details of ASCU.
Indexes
IF-MIBifIndex alpsAscuId
Column Syntax OID
alpsAscuId
Specifies the ASCU Identifier and uniquely
identifies an ASCU on a given interface. This value is
the Interface Address (IA) for ALC and the Remote Identifier
(RID) for UTS. This uniquely identifies an ASCU on a given i…
Integer32
Constraints:
range: 1-127
 .1.3.6.1.4.1.9.9.95.1.5.1.1.1
alpsAscuA1
A1 value of the ASCU.
AlpsAscuA1A2Valuer/w
Textual Convention: AlpsAscuA1A2Value Integer32
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.95.1.5.1.1.2
alpsAscuA2
A2 value of the ASCU.
AlpsAscuA1A2Valuer/w
Textual Convention: AlpsAscuA1A2Value Integer32
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.95.1.5.1.1.3
alpsAscuCktName
Specifies the ALPS Circuit Name for the circuit that is to be
used for this ASCU's data. Note that all ASCUs on a physical interface
may not use the same ALPS circuit to connect to the central router
AlpsCktNamer/w
Textual Convention: AlpsCktName OctetString
Type Constraints:
range: 1..12
 .1.3.6.1.4.1.9.9.95.1.5.1.1.4
alpsAscuAlarmsEnabled
Specifies whether alarms (syslog messages or SNMP traps) will
be generated for this ASCU.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.95.1.5.1.1.5
alpsAscuRetryOption
Specifies the retry option for this ASCU. This specifies the
error message to be sent to the terminal when a message
is dropped at the router. The terminal has three choices -
either retransmit the last message (if the …
Enumerationr/w
Enumerated Values:
1resend
2reenter
3none
 .1.3.6.1.4.1.9.9.95.1.5.1.1.6
alpsAscuMaxMsgLength
Specifies Maximum length of Input Message that can be received
from this ASCU.
bytesInteger32r/w
Constraints:
range: 1-3840
 .1.3.6.1.4.1.9.9.95.1.5.1.1.7
alpsAscuFwdStatusOption
If this flag is set, status messages received from the ASCU are
forwarded to the host. Otherwise they are discarded. Note that these
are relevant only for P1024C (UTS). For ALC, a value of FALSE will
be returned.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.95.1.5.1.1.8
alpsAscuState
Reports the current ASCU Status. ASCUs are initially in
disabled state. They are enabled from the parser
if the operator wants to. This takes them to an UP state from which
they go to a DOWN state if there are too many…
Enumeration
Enumerated Values:
1disabled
2unknown
3down
4up
 .1.3.6.1.4.1.9.9.95.1.5.1.1.9
alpsAscuDownReason
Reports the Down reason for this ASCU if it is down.
Enumeration
Enumerated Values:
1unknown
2noReason
3notDown
4ascuDisabled
5errorThresholdExceeded
 .1.3.6.1.4.1.9.9.95.1.5.1.1.10
alpsAscuOutPackets
Number of packets transmitted to this ASCU.
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.5.1.1.11
alpsAscuOutOctets
Number of octets transmitted to this ASCU.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.5.1.1.12
alpsAscuInPackets
Number of packets received from this ASCU
packetsSNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.5.1.1.13
alpsAscuInOctets
Number of octets received from this ASCU.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.5.1.1.14
alpsAscuDropsGarbledPkts
The number of packets dropped due to the inability to properly
decode them. Examples of garbled packets include packets with bad
CRCs or bad header information
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.5.1.1.15
alpsAscuDropsAscuDown
The number of packets dropped because the ASCU had previously
been declared DOWN due to error thresholds being exceeded.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.5.1.1.16
alpsAscuDropsAscuDisabled
The number of packets dropped because the ASCU had previously
been declared to be in disabled state.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.95.1.5.1.1.17
alpsAscuEnabled
Specifies whether the ASCU has been enabled or not. After
the ASCU has been configured, it must be explicitly enabled to allow
it to be polled.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.95.1.5.1.1.18
alpsAscuRowStatus
This object is used to create a new row or modify or
delete an existing row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.95.1.5.1.1.19
alpsAscuAutoReset
Specifies whether a reset command will be automatically issued
to any non-responsive ALC ASCUs.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.95.1.5.1.1.20

alpsSvcMsgTable

table
.1.3.6.1.4.1.9.9.95.1.6.1 · 1 row entry · 4 columns
Open in standard view 
A list of service messages and its associated number. There is
a default list of service messages (list 0) as well as 
user-configurable service messages. On a per-circuit basis, the 
service message list to use can be selected. The user-configured
service message lists are defined in this table. Note that the
default service messages are not part of this table.
alpsSvcMsgEntry entry .1.3.6.1.4.1.9.9.95.1.6.1.1
Service Messages configured along with its List number and Service
Message Number in that list.
Indexes
alpsSvcMsgListNum alpsSvcMsgNum
Column Syntax OID
alpsSvcMsgListNum
Specifies the Service Msg Number of this Service Msg. A
maximum of 8 Service Message lists can be configured not including
the one for Default/System (when alpsSvcMsgListNum = 0)
Service messages.
Integer32
Constraints:
range: 1-8
 .1.3.6.1.4.1.9.9.95.1.6.1.1.1
alpsSvcMsgNum
Specifies the Service Msg Number of this Service Msg. A Maximum
of 8 messages can be present.
Integer32
Constraints:
range: 1-8
 .1.3.6.1.4.1.9.9.95.1.6.1.1.2
alpsSvcMsg
Specifies the Service Message string .
OctetStringr/w
Constraints:
range: 1-50
 .1.3.6.1.4.1.9.9.95.1.6.1.1.3
alpsSvcMsgRowStatus
This object is used to create a new row or modify or
delete an existing row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.95.1.6.1.1.4

alpsX121ToIpTransTable

table
.1.3.6.1.4.1.9.9.95.1.6.2 · 1 row entry · 3 columns
Open in standard view 
A Translation table between X.121 address and IP address. This
is intended to allow a connection to be established to the
appropriate remote router. The X121 address in the call packet
is used to look up the IP address of the remote peer
alpsX121ToIpTransEntry entry .1.3.6.1.4.1.9.9.95.1.6.2.1
A mapping table between X.121 address and IP address.
Indexes
IF-MIBifIndex alpsX121
Column Syntax OID
alpsX121
Specfies the X.121 address of the VC established with
EMTOX host.
RFC1382-MIBX121Address
Textual Convention: RFC1382-MIBX121Address OctetString
Type Constraints:
range: 0..17
 .1.3.6.1.4.1.9.9.95.1.6.2.1.1
alpsIpAddress
This is the IP address of the remote peer which maps onto the
X.121 address.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.9.9.95.1.6.2.1.2
alpsX121ToIpTransRowStatus
This object is used to create a new row or modify or
delete an existing row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.95.1.6.2.1.3