alpsCktBaseNumActiveAscus
CISCO-ALPS-MIB ·
.1.3.6.1.4.1.9.9.95.1.3.1.1.7
Object
column
Integer32
Reports the number of enabled ASCUs that are attached to this ALPS Circuit. Attachment of an ASCU to an ALPS circuit may occur due to configuration or due to information passed in a protocol message.
Context
- MIB
- CISCO-ALPS-MIB
- OID
.1.3.6.1.4.1.9.9.95.1.3.1.1.7- Type
- column
- Access
- readonly
- Status
- current
- Parent
- alpsCktBaseEntry
- Table
- alpsCktBaseTable
- Siblings
- 23
Syntax
Integer32
Values & Constraints
Object Constraints
range: 0-64
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| alpsCktBaseName Specifies the ALPS Circuit Name. This is unique within the
network. | column | AlpsCktName | .1.3.6.1.4.1.9.9.95.1.3.1.1.1 |
| alpsCktBaseHostLinkNumber Specifies host link number (on Central router) for this ALPS
Circuit. The host link number is used to provide a
degree of transparency to the remote router. A single host link
ma… | column | Integer32 | .1.3.6.1.4.1.9.9.95.1.3.1.1.10 |
| alpsCktBaseHostLinkType Specifies host link type(on Central router) for this
ALPS Circuit. | column | Enumeration | .1.3.6.1.4.1.9.9.95.1.3.1.1.11 |
| alpsCktBaseRemHld Specifies the HLD (High-level descriptor) of the AX.25/EMTOX
host for this ALPS Circuit. This serves as an identifier
for the host | column | Integer32 | .1.3.6.1.4.1.9.9.95.1.3.1.1.12 |
| alpsCktBaseLocalHld Specifies the local HLD for this ALPS Circuit. HLDs are required
at the host for both ends of the connection. | column | Integer32 | .1.3.6.1.4.1.9.9.95.1.3.1.1.13 |
| alpsCktBaseDownReason Reports the reason why this ALPS Circuit is down, if it is down. | column | Enumeration | .1.3.6.1.4.1.9.9.95.1.3.1.1.14 |
| alpsCktBaseOutPackets Number of packets transmitted to remote peer over this circuit. | column | packets SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.95.1.3.1.1.15 |
| alpsCktBaseOutOctets Number of octets transmitted to remote peer over this circuit. | column | octets SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.95.1.3.1.1.16 |
| alpsCktBaseInPackets Number of packets received from remote peer over this circuit. | column | packets SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.95.1.3.1.1.17 |
| alpsCktBaseInOctets Number of octets received from remote peer over this circuit. | column | octets SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.95.1.3.1.1.18 |
| alpsCktBaseDropsCktDisabled Number of packets dropped because the circuit was disabled. This
would typically be packets that were queueued before the circuit was
disabled which are now left in the queue. | column | packets SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.95.1.3.1.1.19 |
| alpsCktBaseDlcType Specifies what type of circuit this is. The X25 circuit is set up
with the same name as the P1024 circuit so we need this
variable to distinguish between the two, in case local s… | column | Enumeration | .1.3.6.1.4.1.9.9.95.1.3.1.1.2 |
| alpsCktBaseDropsQOverflow Number of packets dropped due to TCP Congestion. | column | packets SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.95.1.3.1.1.20 |
| alpsCktBaseDropsLifeTimeExpd Number of packets which were queued within the router for
longer than alpsCktBaseLifeTimeTimer. | column | packets SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.95.1.3.1.1.21 |
| alpsCktBaseEnabled This specifies if the circuit has been enabled. After a circuit
has been configured, it must be explicitly enabled in order for
the circuit to be set up. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.95.1.3.1.1.22 |
| alpsCktBaseRowStatus This object is used to create a new row or modify or
delete an existing row in this table. | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.9.9.95.1.3.1.1.23 |
| alpsCktBaseCurrPeerConnId A descriptive ASCII string that is used to distinguish
among different peer connections to the same ALPS remote
peer IP address. | column | OctetString | .1.3.6.1.4.1.9.9.95.1.3.1.1.24 |
| alpsCktBasePriPeerAddr This is the IP address of the Primary Central peer. It is
mandatory to configure a primary peer, but the backup peer is
optional. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.9.9.95.1.3.1.1.3 |
| alpsCktBaseAlarmsEnabled Specifies whether alarms are generated for this ALPS circuit.
Alarms can be syslog messages or SNMP traps - both are controlled
using the same flags. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.95.1.3.1.1.4 |
| alpsCktBaseConnType Specifies the ALPS Circuit Connection Type. | column | Enumeration | .1.3.6.1.4.1.9.9.95.1.3.1.1.5 |
| alpsCktBaseState Indicates the state of ALPS Circuit. | column | Enumeration | .1.3.6.1.4.1.9.9.95.1.3.1.1.6 |
| alpsCktBaseCurrentPeer Reports the IP address of the peer that this ALPS circuit
is currently connected to. | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.9.9.95.1.3.1.1.8 |
| alpsCktBaseLifeTimeTimer A data message that has been queued within the router for
longer than this interval will be dropped. | column | SNMPv2-TCTimeInterval | .1.3.6.1.4.1.9.9.95.1.3.1.1.9 |