alpsAscuState

CISCO-ALPS-MIB · .1.3.6.1.4.1.9.9.95.1.5.1.1.9
MIB view Table view

Object

column Enumeration 
Reports the current ASCU Status. ASCUs are initially in
disabled state. They are enabled from the parser
if the operator wants to. This takes them to an UP state from which 
they go to a DOWN state if there are too many errors.

Context

MIB
CISCO-ALPS-MIB
OID
.1.3.6.1.4.1.9.9.95.1.5.1.1.9
Type
column
Access
readonly
Status
current
Parent
alpsAscuEntry
Table
alpsAscuTable
Siblings
19

Syntax

Enumeration

Values & Constraints

Enumerated Values
1disabled
2unknown
3down
4up

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
alpsAscuId
Specifies the ASCU Identifier and uniquely identifies an ASCU on a given interface. This value is the Interface Address (IA) for ALC and the Remote Identifier (RID) for UTS. This …
columnInteger32.1.3.6.1.4.1.9.9.95.1.5.1.1.1
alpsAscuDownReason
Reports the Down reason for this ASCU if it is down.
columnEnumeration.1.3.6.1.4.1.9.9.95.1.5.1.1.10
alpsAscuOutPackets
Number of packets transmitted to this ASCU.
columnpackets SNMPv2-SMICounter32.1.3.6.1.4.1.9.9.95.1.5.1.1.11
alpsAscuOutOctets
Number of octets transmitted to this ASCU.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.9.9.95.1.5.1.1.12
alpsAscuInPackets
Number of packets received from this ASCU
columnpackets SNMPv2-SMICounter32.1.3.6.1.4.1.9.9.95.1.5.1.1.13
alpsAscuInOctets
Number of octets received from this ASCU.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.9.9.95.1.5.1.1.14
alpsAscuDropsGarbledPkts
The number of packets dropped due to the inability to properly decode them. Examples of garbled packets include packets with bad CRCs or bad header information
columnSNMPv2-SMICounter32.1.3.6.1.4.1.9.9.95.1.5.1.1.15
alpsAscuDropsAscuDown
The number of packets dropped because the ASCU had previously been declared DOWN due to error thresholds being exceeded.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.9.9.95.1.5.1.1.16
alpsAscuDropsAscuDisabled
The number of packets dropped because the ASCU had previously been declared to be in disabled state.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.9.9.95.1.5.1.1.17
alpsAscuEnabled
Specifies whether the ASCU has been enabled or not. After the ASCU has been configured, it must be explicitly enabled to allow it to be polled.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.95.1.5.1.1.18
alpsAscuRowStatus
This object is used to create a new row or modify or delete an existing row in this table.
columnSNMPv2-TCRowStatus.1.3.6.1.4.1.9.9.95.1.5.1.1.19
alpsAscuA1
A1 value of the ASCU.
columnAlpsAscuA1A2Value.1.3.6.1.4.1.9.9.95.1.5.1.1.2
alpsAscuAutoReset
Specifies whether a reset command will be automatically issued to any non-responsive ALC ASCUs.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.95.1.5.1.1.20
alpsAscuA2
A2 value of the ASCU.
columnAlpsAscuA1A2Value.1.3.6.1.4.1.9.9.95.1.5.1.1.3
alpsAscuCktName
Specifies the ALPS Circuit Name for the circuit that is to be used for this ASCU's data. Note that all ASCUs on a physical interface may not use the same ALPS circuit to connect t…
columnAlpsCktName.1.3.6.1.4.1.9.9.95.1.5.1.1.4
alpsAscuAlarmsEnabled
Specifies whether alarms (syslog messages or SNMP traps) will be generated for this ASCU.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.95.1.5.1.1.5
alpsAscuRetryOption
Specifies the retry option for this ASCU. This specifies the error message to be sent to the terminal when a message is dropped at the router. The terminal has three choices - eit…
columnEnumeration.1.3.6.1.4.1.9.9.95.1.5.1.1.6
alpsAscuMaxMsgLength
Specifies Maximum length of Input Message that can be received from this ASCU.
columnbytes Integer32.1.3.6.1.4.1.9.9.95.1.5.1.1.7
alpsAscuFwdStatusOption
If this flag is set, status messages received from the ASCU are forwarded to the host. Otherwise they are discarded. Note that these are relevant only for P1024C (UTS). For ALC, a…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.95.1.5.1.1.8