alpsCktP1024SvcMsgList

CISCO-ALPS-MIB · .1.3.6.1.4.1.9.9.95.1.3.3.1.11
MIB view Table view

Object

column r/w Integer32 
Specifies the Service Message List Number to use on this
ALPS Circuit. This allows custom service messages to be sent
for ASCUs on a particular circuit. Service messages are sent out 
by the router to the ASCU when abnormal conditions occur, and are
displayed on the terminal. There is a default set of service
messages, usually referred to as List 0. However, it is possible
to configure custom sets of service messages for display,
selectable on a per-circuit basis.

Context

MIB
CISCO-ALPS-MIB
OID
.1.3.6.1.4.1.9.9.95.1.3.3.1.11
Type
column
Access
readwrite
Status
current
Parent
alpsCktP1024Entry
Table
alpsCktP1024Table
Siblings
14

Syntax

Integer32

Values & Constraints

Object Constraints
range: 0-8

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
alpsCktP1024DlcType
Specifies what type of circuit this is.
columnEnumeration.1.3.6.1.4.1.9.9.95.1.3.3.1.1
alpsCktP1024InPktSize
Specifies X.25 maximum input Packet size on the Logical Channel Number of this ALPS Circuit. The default input Packet size for AX.25 is 240 bytes and 128 bytes for EMTOX.
columnbytes Integer32.1.3.6.1.4.1.9.9.95.1.3.3.1.10
alpsCktP1024SvcMsgIntvl
Specifies Service Message Time Interval for the Service messages to be sent this ALPS Circuit. This controls how frequently the messages are repeated when an error condition (e.g…
columnSNMPv2-SMITimeTicks.1.3.6.1.4.1.9.9.95.1.3.3.1.12
alpsCktP1024DropsUnkAscu
Number of packets that were found to be from an Unknown ASCU (i.e. an ASCU that had not been configured) and hence were dropped.
columnpackets SNMPv2-SMICounter32.1.3.6.1.4.1.9.9.95.1.3.3.1.13
alpsCktP1024RowStatus
This object is used to create a new row or modify or delete an existing row in this table.
columnSNMPv2-TCRowStatus.1.3.6.1.4.1.9.9.95.1.3.3.1.14
alpsCktP1024MatipCloseDelay
Specifies the minumum delay between transmission of a MATIP Close and the transmission of a MATIP Session Open for this ALPS circuit.
columnSNMPv2-TCTimeInterval.1.3.6.1.4.1.9.9.95.1.3.3.1.15
alpsCktP1024BackupPeerAddr
This is the IP address of the backup remote peer. This is optional and hence may not always exist.
columnSNMPv2-SMIIpAddress.1.3.6.1.4.1.9.9.95.1.3.3.1.2
alpsCktP1024RetryTimer
Specifies the interval at which a permanent ALPS circuit will attempt to reestablish the circuit in case it wasn't able to come up.
columnSNMPv2-TCTimeInterval.1.3.6.1.4.1.9.9.95.1.3.3.1.3
alpsCktP1024IdleTimer
If there is no traffic on a dynamic ALPS circuit for this interval, it will be cleared.
columnSNMPv2-TCTimeInterval.1.3.6.1.4.1.9.9.95.1.3.3.1.4
alpsCktP1024EmtoxX121
Specifies the X.121 address of the SVC established with EMTOX host. This field should be set to length zero in the case of PVCs (AX.25 host).
columnRFC1382-MIBX121Address.1.3.6.1.4.1.9.9.95.1.3.3.1.5
alpsCktP1024Ax25LCN
Specifies the Logical Channel Number being used on the PVC established with AX.25 host. This field should be set to zero in the case of SVCs (EMTOX host).
columnInteger32.1.3.6.1.4.1.9.9.95.1.3.3.1.6
alpsCktP1024WinOut
Specifies X.25 transmit Window size on the Logical Channel Number of this ALPS Circuit.
columnInteger32.1.3.6.1.4.1.9.9.95.1.3.3.1.7
alpsCktP1024WinIn
Specifies the X.25 receive Window size on the Logical Channel Number of this ALPS Circuit.
columnInteger32.1.3.6.1.4.1.9.9.95.1.3.3.1.8
alpsCktP1024OutPktSize
Specifies the X.25 maxiumum output Packet size on the Logical Channel Number of this ALPS Circuit. The default output Packet size for AX.25 is 240 bytes and 128 bytes for EMTOX.
columnbytes Integer32.1.3.6.1.4.1.9.9.95.1.3.3.1.9