CISCO-MGX82XX-DSX3-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
8
Rows
8
Columns
186

cwDsx3ConfigTable

table
.1.3.6.1.4.1.351.110.4.4.1.1.1 · 1 row entry · 32 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk cwDsx3ConfigTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-MGX82XX-DSX3-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-MGX82XX-DSX3-MIB::cwDsx3ConfigTable' 
The DS3/E3 Configuration table. There is one row for each
DSX3 port in the system. The table size (number of 
rows) is given by the value of dsx3LineNumOfValidEntries.
cwDsx3ConfigEntry row .1.3.6.1.4.1.351.110.4.4.1.1.1.1
An entry in the DSX3 Configuration table.
Indexes
Column Syntax OID
dsx3LineNum
This object is the identifier of a DS3/E3
Interface on a managed device.

The range supported depends upon the type of
the card(controller card, service module).

For 1 port Card : Range is …
Integer32
Constraints:
range: 1-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.1
cwDsx3LineType
This variable indicates the variety of DS3 C-bit
or E3 application implementing this interface.
The type of interface affects the interpretation
of the usage and error statistics. The rate of DS3
is 44.736 Mbps and E3 i…
Enumerationr/w
Enumerated Values:
1dsx3CbitParity
2g832-g804
3dsx3M23
4g751
5dsx3Unframed
6e3Unframed
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.2
cwDsx3LineCoding
This variable describes the variety of Zero Code
Suppression used on this interface, which in turn
affects a number of its characteristics.

dsx3B3ZS and e3HDB3 refer to the use of specified
patterns of no…
Enumerationr/w
Enumerated Values:
1dsx3B3ZS
2e3HDB3
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.3
cwDsx3LineLength
This object specifies the length of the
DS3 Line. This object provides information
for line build out circuitry if it exists
and can use this object to adjust the
line build out.
Enumerationr/w
Enumerated Values:
1lessThan225
2moreThan225
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.4
dsx3LineOOFCriteria
This object specifies the out of frame decision
criteria.
OOF is declared when errors are detected in the
framing octets for four consecuitive frames.

fBits3Of8(1) : an OOF condition is declared if at…
Enumerationr/w
Enumerated Values:
1fBits3Of8
2fBits3Of16
3notApplicable
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.5
dsx3LineAIScBitsCheck
If check C-Bits options is chosen then AIS is declared
when 1010 pattern is found and C-Bits are all zero.
In the other case an AIS condition is declared when the
AIS pattern 1010... is detected irrespective of the sta…
Enumerationr/w
Enumerated Values:
1checkCbits
2ignorebits
3notApplicable
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.6
dsx3LineLoopbackCommand
This variable represents the loopback configuration
of the DS3/E3 interface.
The values mean:
dsx3NoLoop
Not in the loopback state. A device that is
not capable of performing a loopback on
t…
Enumerationr/w
Enumerated Values:
1dsx3NoLoop
2dsx3RemoteLineLoop
3dsx3LocalLineLoop
4dsx3InbndLocalLoopback
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.7
dsx3LineRcvFEACValidation
This entry specifies the FEAC code validation criteria.
fFEACCodes4Of5(1) : a valid FEAC code is declared if
4 of 5 codes match.
fFEACCodes8Of10(2): a valid FEAC code is declared if
…
Enumerationr/w
Enumerated Values:
1fFEACCodes4Of5
2fFEACCodes8Of10
3fFEACCodesDisable
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.8
dsx3LineXmtFEACCode
This variable indicates what bit-oriented code to transmit
over the far-end alarm and control (FEAC) channel.

The values mean:

dsx3SendNoCode
sending looped or normal data
dsx3SendLineC…
Enumerationr/w
Enumerated Values:
1dsx3SendNoCode
2dsx3SendLineCode
3dsx3SendPayloadCode
4dsx3SendResetCode
5dsx3SendDS1LoopCode
6dsx3SendTestPattern
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.9
dsx3LineBERTEnable
This object enables/disables the BERT function on
an interface.

The possible values are :
disabled(1): disables port BERT functionality
enabled (2): enables port BERT functionality.
…
Enumerationr/w
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.10
dsx3LineBERTPattern
This object defines the test bit pattern to be
used for BERT.

The possible values are :

Repetitive Patterns

allZero(1): All Zeroes(Continuous spaces). This is
rep…
Enumerationr/w
Enumerated Values:
1allZero
2allOnes
3alternateOneZero
4doubleOneZero
5userOneWord
6userTwoWords
7userThreeWords
8userFourWords
9pattern2p15minus1
10pattern2p20minus1
11pattern2p23minus1
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.11
dsx3LineBERTResult
Result of BERT Test. The value in this object
is not applicable if dsx3LineBERTEnable is set to
disabled(1).
Enumeration
Enumerated Values:
1bertFailed
2bertPassed
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.12
dsx3BERTResultClrButton
Setting this object to clear(2) causes the BERT
result field to get cleared.
Enumerationr/w
Enumerated Values:
1noAction
2clear
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.13
dsx3TrailTraceOption
This object is used for enabling/disabling
G.832 Trail Trace. The trail trace is used to
repetitively transmit a trail access point identifier
so that a trail receiving terminal can verify its
continued connection to…
Enumerationr/w
Enumerated Values:
1disable
2enable
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.14
dsx3TxTrailTrace
This object is used for specifying the
data to be used for G.832 Trail Trace ID/String.
This object is applicable only for E3 interfaces
with G.832 framing.

The trail trace ID is a 16 octet field that
co…
OctetStringr/w
Constraints:
range: 1-15
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.15
dsx3RxTrailTrace
Received G.832 Trail Trace string.
The format of the value is:
First byte indicates CRC-7(frame start marker).
Bytes 2-6 (ASCII) [Byte 1-5 of this object]
Bytes 7-11 (ASCII) [Byte 6-10 of this object]
Bytes …
OctetString
Constraints:
range: 1-15
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.16
dsx3TxTimingMarker
Transmitted timing marker bit in G.832 MA byte.
This object can be set to traceable(1) to indicate
that the timing source is traceable to a primary
reference clock and is otherwise set to untraceable(2).
…
Enumerationr/w
Enumerated Values:
1traceable
2untraceable
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.17
dsx3RxTimingMarker
Received timing marker bit in G.832 MA byte.
This object can be set to traceable(1) to indicate
that the timing source is tracable to a primary
reference clock and is otherwise set to untraceable(2).

Thi…
Enumerationr/w
Enumerated Values:
1traceable
2untraceable
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.18
dsx3TxPayloadType
This object specifies the G.832 payload type
for transmit data.

The possible values are :

unequipped (1): not carrying any payload
equipped (2): Equipped,non-specific
atm (3)…
Enumerationr/w
Enumerated Values:
1unequipped
2equipped
3atm
4sdhtu12s
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.19
dsx3RxPayloadType
Received payload type field in G.832 byte

The possible values are :

unequipped (1): not carrying any payload
equipped (2): Equipped,non-specific
atm (3): ATM
sdhtu12s (4):…
Enumeration
Enumerated Values:
1unequipped
2equipped
3atm
4sdhtu12s
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.20
dsx3TxTumf
This object contains the value of
Tributary Multiframe Indicator(bits 6 and 7 of MA byte)
in case of TU-1xs mapping.

This is not supported in FRSM-VHS and CESM-T3/E3.
Integer32
Constraints:
range: 0-3
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.21
dsx3RxTumf
This object contains the value of
Tributary Multiframe Indicator(bits 6 and 7 of MA byte)
in case of TU-1xs mapping.

This object is not supported in FRSM-VHS
and CESM-T3/E3.
Integer32
Constraints:
range: 0-3
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.22
dsx3LineEnable
This object is used for enabling/disabling an interface
and modifying the interface configuration.

The possible values are:

disable (1): Interface is administratively down
enable (2): …
Enumerationr/w
Enumerated Values:
1disable
2enable
3modify
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.23
dsx3FarEndLoopbkLineNum
Specify which DS1 or DS3 line in the far-end for the
loopback testing.
For CESM-T3/E3, only ds3line(30) is valid.
Enumerationr/w
Enumerated Values:
1ds1line1
2ds1line2
3ds1line3
4ds1line4
5ds1line5
6ds1line6
7ds1line7
8ds1line8
9ds1line9
10ds1line10
11ds1line11
12ds1line12
13ds1line13
14ds1line14
15ds1line15
16ds1line16
17ds1line17
18ds1line18
19ds1line19
20ds1line20
21ds1line21
22ds1line22
23ds1line23
24ds1line24
25ds1line25
26ds1line26
27ds1line27
28ds1line28
29ds1line29
30ds3line
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.24
dsx3LineXmtClockSrc
The source of the transmit clock.

backplaneClk(2) : clock source is from the backplane.
recoverClk (3) : clock source is derived from another
t3 interface.
localClk (4) : clock sourc…
Enumerationr/w
Enumerated Values:
1backplaneClk
2recoverClk
3localClk
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.25
dsx3FarEndLoopbkLineStatus
This is a bitmap of the DSX3 FarEnd line
loopback status bits

Bit Position Loopback indicator
----------- -----
1 DS1 Line 1
2 DS1 Line 2
3 DS1 Line 3
4 …
Integer32
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.26
dsx3LineEqualizer
This object indicates whether the internal equalizer
is being used or bypassed. Set this value depending on
the line equipment to which the receiver is attached.

intrnlequalizer(1): Use internal line equa…
Enumerationr/w
Enumerated Values:
1intrnlequalizer
2extequalizer
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.27
dsx3NearEndLoopbkLineStatus
This is a bitmap of the DSX3 NearEnd line
loopback status bits
BitPosition Loopback indicator
----------- -----
1 DS1 Line 1
2 DS1 Line 2
3 DS1 Line 3
4 DS1 Line…
Integer32
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.28
dsx3SubRateEnable
This variable controls whether the DS3 subrates are
enabled or not. The DS3 subrate is part of
DSU functionality.
This object is currently supported only in FRSM-VHS
cards.

It is recommended that this obj…
Enumerationr/w
Enumerated Values:
1disable
2enable
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.29
dsx3DsuSelect
The dsx3DsuSelect variable controls the type of DSU mode
to be selected. The 'dsx3SubRateEnable' has to be set to
'enable' before selecting the mode in 'dsx3DsuSelect'.

The possible values for this are :…
Enumerationr/w
Enumerated Values:
1dl3100Mode
2adcKentroxMode
3larsCom
4clearChannel
5dsuAlgorithm2
6dsuAlgorithm3
7dsuAlgorithm4
8dsuAlgorithm5
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.30
dsx3LineRate
The desired line rate when 'dsx3SubRateEnable' is enabled.
If dsx3DsuSelect is set to 'dl3100Mode', the line rate can
be configured in steps of 300 Kbps.
If dsx3DsuSelect is set to 'adcKentroxMode', the line rate can
b…
kbpsInteger32r/w
Constraints:
range: 300-44736
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.31
dsx3LineScrambleEnable
This variable turns the scrambling feature ON/OFF
The scrambling is a technique that enables framing
to be maintained on certain medium-speed edge and
trunk interfaces.

This object is ONLY applicable for…
Enumerationr/w
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.351.110.4.4.1.1.1.1.32

dsx3AlarmConfigTable

table
.1.3.6.1.4.1.351.110.4.4.1.2.1 · 1 row entry · 39 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk dsx3AlarmConfigTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-MGX82XX-DSX3-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-MGX82XX-DSX3-MIB::dsx3AlarmConfigTable' 
The DSX3 interface alarm configuration table. This table contains
the parameters associated with detecting and declaring alarms for
the interface. The parameters include severity of alarm, alarm
integration parameters and 15 minute and 24 hour thresholds. 
The number of rows is given by dsx3LineNumOfValidEntries.
dsx3AlarmConfigEntry row .1.3.6.1.4.1.351.110.4.4.1.2.1.1
An entry in the DSX3 Alarm Configuration table.

Thresholds may be configured for:

Line Code Violations (LCV),
LineErrored Seconds (LES),
Line Severely Errored Se…
Indexes
Column Syntax OID
dsx3RedSeverity
This variable is used to setup the severity of RED
alarm. So when LOS/LOF alarm is detected the card will
send the alarm with appropriate severity status.
A major alarm will cause audible notification
and the MAJOR ALAR…
Enumerationr/w
Enumerated Values:
1minor
2major
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.1
dsx3RAISeverity
This variable is used to setup the severity of RAI
alarm. So when RAI alarm is detected the card will
send the alarm with appropriate severity status.
A major alarm will cause the audible notification
and the MAJOR ALAR…
Enumerationr/w
Enumerated Values:
1minor
2major
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.2
dsx3NEAlarmUpCount
This parameter specifies the increment to the
Near End alarm integration counters. The local
alarms are LOS and LOF. The Default value is 6
and the integration counter is incremented by
this value every 10 ms while the…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.3
dsx3NEAlarmDownCount
This parameter specifies the decrement to the
Near End alarm integration counters. The local
alarms are LOS and LOF. The Default value is 1 and
the integration counter is decremented by this value
every 10 ms while …
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.4
dsx3NEAlarmThreshold
The value set in this object determines the value that
the alarm integration counter must reach for an near end
Alarm to be declared. If the up count is 6, the down count
is 1 and the threshold 1500, an Alarm is integra…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.5
dsx3FEAlarmUpCount
This parameter specifies the increment to the
Far End alarm integration counters. The local alarms
are RAI and AIS. The Default value is 6 and the
integration counter is incremented by this value every
10 ms while t…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.6
dsx3FEAlarmDownCount
This parameter specifies the decrement to the
Far End alarm integration counters. The local alarms
are AIS and RAI. The Default value is 1. The integration
counter is decremented by this value every 10 ms
(till zero…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.7
dsx3FEAlarmThreshold
The value set in this object determines the value that
the alarm integration counter must reach for an far end
Alarm to be declared. If the up count is 6, the down count
is 1 and the threshold 1500, an Alarm is integrat…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.8
dsx3StatisticalAlarmSeverity
This variable is used to setup the severity of
any of the Statistical alarms. So when a
Statistical Counter exceeds its specified threshold
the card will send the alarm with appropriate
severity. A major alarm will c…
Enumerationr/w
Enumerated Values:
1minor
2major
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.9
dsx3LCV15MinThreshold
The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.10
dsx3LCV24HrThreshold
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.11
dsx3LES15MinThreshold
The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.12
dsx3LES24HrThreshold
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.13
dsx3LSES15MinThreshold
The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.14
dsx3LSES24HrThreshold
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.15
dsx3PCV15MinThreshold
The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
This object is not supported in CESM-T3/E3.
This object is not applicable for E3 i…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.16
dsx3PCV24HrThreshold
The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interva…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.17
dsx3PES15MinThreshold
The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
This object is not supported in CESM-T3/E3.
This object is not applicable for E3 i…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.18
dsx3PES24HrThreshold
The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interva…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.19
dsx3PSES15MinThreshold
The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.

This object does not apply to the E3 interface.

This o…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.20
dsx3PSES24HrThreshold
The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interv…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.21
dsx3SEFS15MinThreshold
The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
This object is not supported in CESM-T3/E3
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.22
dsx3SEFS24HrThreshold
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval.
…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.23
dsx3AISS15MinThreshold
The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
This object is not supported in CESM-T3/E3
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.24
dsx3AISS24HrThreshold
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval
T…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.25
dsx3UAS15MinThreshold
The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.26
dsx3UAS24HrThreshold
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.27
dsx3E3BIP8CV15MinThreshold
G.832 BIP-8 error monitoring byte. 15 minute
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS
This object is not supported in CESM-T3/E3.
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.28
dsx3E3BIP8CV24HrThreshold
G.832 BIP-8 error monitoring byte. 24 hour
threshold value.

This has no significance to E3 with G.751 framing
which is used in FRSM-VHS.

This object is not supported in CESM-T3/E3.
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.29
dsx3E3BIP8ES15MinThreshold
G.832 BIP-8 error monitoring byte. 15 minute
threshold value.

This has no significance to E3 with G.751 framing
which is used in FRSM-VHS.

This object is not supported in CESM-T3/E3.
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.30
dsx3E3BIP8ES24HrThreshold
G.832 BIP-8 error monitoring byte. 24 hour
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS
This object is not supported in CESM-T3/E3
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.31
dsx3E3BIP8SES15MinThreshold
G.832 BIP-8 error monitoring byte. 15 minute
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS
This object is not supported in CESM-T3/E3
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.32
dsx3E3BIP8SES24HrThreshold
G.832 BIP-8 error monitoring byte. 24 hour
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS
This object is not supported in CESM-T3/E3
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.33
dsx3CCV15MinThreshold
The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.

This object is not applicable for E3 interface.

This…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.34
dsx3CCV24HrThreshold
The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interva…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.35
dsx3CES15MinThreshold
The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.

This object is not applicable for E3 interface.

This…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.36
dsx3CES24HrThreshold
The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.

This object is not applicable for E3 interface.
…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.37
dsx3CSES15MinThreshold
The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.

This object is not applicable for E3 interface.

This o…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.38
dsx3CSES24HrThreshold
The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared.

This object is not applicable for E3 interface.

…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.2.1.1.39

dsx3AlarmTable

table
.1.3.6.1.4.1.351.110.4.4.1.3.1 · 1 row entry · 49 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk dsx3AlarmTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-MGX82XX-DSX3-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-MGX82XX-DSX3-MIB::dsx3AlarmTable' 
The DSX3 interface alarm table. This table
contains the performance statistics and Error Events
based on 15 minute and/or 24 hour interval.
          
Performance Parameters:
    LES  : Line Errored Seconds
    PES  : P-bit Errored Seconds
    PSES : P-bit Severely Errored Seconds
    CES  : C-bit Errored Seconds
    CSES : C-bit Severely Errored Seconds
    SEFS : Severely Errored Framing Seconds
    UAS  : Unavailable Seconds
          
Error Events:
    BPV : Bipolar Violation
    EXZ : Excessive Zeros
    LCV : Line Coding Violation
    PCV : P-bit Coding Violation
    CCV : C-bit Coding Violation.
dsx3AlarmEntry row .1.3.6.1.4.1.351.110.4.4.1.3.1.1
An entry in the DSX3 Alarm table. The bucket
statistics(15 minute and 24 hour interval statistics)
are gathered for each ds3/e3 interface.
Any entry is created automatically when ds3 interface
is created.
Indexes
Column Syntax OID
dsx3LineAlarmState
This variable is a bitmap of the DSX3 Line ALarms
on the card. A value of zero indicates no alarms.

Itemized below are the individual bits:
BitPosition Alarm
----------- -----
0 Receivi…
Integer32
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.1
dsx3LineStatisticalAlarmState
This is a bitmap of the DSX3 Line Statistical
Alarms on the card. Zero indicates no alarms.

Itemized below are the individual alarm bits:

BitPosition Alarm
----------- -----
0 …
Integer32
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.2
dsx3LCVCurrent
The number of Line Code Violations(LCV)
encountered by the interface in current
15 minute period.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.3
dsx3LCV15MinBucket
The number of Line Code Violations(LCV)
encountered by the interface in current
last 15 minute period.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.4
dsx3LCV24HrBucket
The number of Line Code Violations(LCV)
encountered by the interface in current
last 24 hour period.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.5
dsx3LESCurrent
The number of Line Errored Seconds(LES)
encountered by the interface in current
15 minute period.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.6
dsx3LES15MinBucket
The number of Line Errored Seconds(LES)
encountered by the interface in last
15 minute period.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.7
dsx3LES24HrBucket
The number of Line Errored Seconds(LES)
encountered by the interface in last
24 hour period.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.8
dsx3LSESCurrent
The number of Line Severely Errored Seconds(LSES)
encountered by the interface in current
15 minute period.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.9
dsx3LSES15MinBucket
The number of Line Severely Errored Seconds(LSES)
encountered by the interface in last
15 minute period.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.10
dsx3LSES24HrBucket
The number of Line Severely Errored Seconds(LSES)
encountered by the interface in last
24 hour period.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.11
dsx3PCVCurrent
The number of P-bit Coding Violations(PCV)
encountered by the interface in current
15 minute period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.12
dsx3PCV15MinBucket
The number of P-bit Coding Violations(PCV)
encountered by the interface in last
15 minute period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.13
dsx3PCV24HrBucket
The number of P-bit Coding Violations(PCV)
encountered by the interface in last
24 Hour period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.14
dsx3PESCurrent
The number of P-bit Errored Seconds(PES)
encountered by the interface in current
15 minute period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.15
dsx3PES15MinBucket
The number of P-bit Errored Seconds(PES)
encountered by the interface in last
15 minute period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.16
dsx3PES24HrBucket
The number of P-bit Errored Seconds(PES)
encountered by the interface in last
24 Hour period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.17
dsx3PSESCurrent
The number of P-bit Severely Errored
Seconds(PSES) encountered by the interface
in current 15 minute period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.18
dsx3PSES15MinBucket
The number of P-bit Severely Errored
Seconds(PSES) encountered by the interface
in last 15 minute period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.19
dsx3PSES24HrBucket
The number of P-bit Severely Errored
Seconds(PSES) encountered by the interface
in last 24 Hour period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.20
dsx3SEFSCurrent
The number of Severely Errored Framing
Seconds(PSES) encountered by the interface
in current 15 minute period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.21
dsx3SEFS15MinBucket
The number of Severely Errored Framing
Seconds(PSES) encountered by the interface
in last 15 minute period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.22
dsx3SEFS24HrBucket
The number of Severely Errored Framing
Seconds(PSES) encountered by the interface
in last 24 Hour period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.23
dsx3AISSCurrent
The number of AIS Severely Errored Seconds
encountered by the interface in current 15 minute
period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.24
dsx3AISS15MinBucket
The number of AIS Severely Errored Seconds
encountered by the interface in last 15 minute
period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.25
dsx3AISS24HrBucket
The number of AIS Severely Errored Seconds
encountered by the interface in last 24 Hour
period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.26
dsx3UASCurrent
The number of Unavailable Seconds(UAS)
encountered by the interface in current
15 minute period.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.27
dsx3UAS15MinBucket
The number of Unavailable Seconds(UAS)
encountered by the interface in last
15 minute period.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.28
dsx3UAS24HrBucket
The number of Unavailable Seconds(UAS)
encountered by the interface in last
24 Hour period.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.29
dsx3PercentLcvEFS
This object gives the percentage of
seconds without any LCV Errors in the
total elapsed seconds.
Integer32
Constraints:
range: 0-100
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.30
dsx3E3BIP8CVCurrent
The number of G.832 BIP-8 Coding Violations
(CV) encountered by the interface in current
15 minute period.

This object is not supported in FRSM-VHS and
CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.31
dsx3E3BIP8CV15MinBucket
The number of G.832 BIP-8 Coding Violations
(CV) encountered by the interface in last
15 minute period.

This object is not supported in FRSM-VHS and
CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.32
dsx3E3BIP8CV24HrBucket
The number of G.832 BIP-8 Coding Violations
(CV) encountered by the interface in last
24 Hour period.

This object is not supported in FRSM-VHS and
CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.33
dsx3E3BIP8ESCurrent
The number of G.832 BIP-8 Errored Seconds(ES)
encountered by the interface in current
15 minute period.

This object is not supported in FRSM-VHS and
CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.34
dsx3E3BIP8ES15MinBucket
The number of G.832 BIP-8 Errored Seconds(ES)
encountered by the interface in last
15 minute period.

This object is not supported in FRSM-VHS and
CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.35
dsx3E3BIP8ES24HrBucket
The number of G.832 BIP-8 Errored Seconds(ES)
encountered by the interface in last
24 Hour period.

This object is not supported in FRSM-VHS and
CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.36
dsx3E3BIP8SESCurrent
The number of G.832 BIP-8 Severely Errored Seconds(SES)
encountered by the interface in current 15 minute period.

This object is not supported in FRSM-VHS and
CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.37
dsx3E3BIP8SES15MinBucket
The number of G.832 BIP-8 Severely Errored Seconds(SES)
encountered by the interface in last 15 minute period.

This object is not supported in FRSM-VHS and
CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.38
dsx3E3BIP8SES24HrBucket
The number of G.832 BIP-8 Severely Errored Seconds(SES)
encountered by the interface in last 24 Hour period.

This object is not supported in FRSM-VHS and
CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.39
dsx3LineAlarmClrButton
Setting this object to dsx3LineAlarmClear will
cause all the alarms statuses and counters to reset.
Enumerationr/w
Enumerated Values:
1noAction
2clear
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.40
dsx3CCVCurrent
The number of C-bit Coding Violations(CCV)
encountered by the interface in current
15 minute period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.41
dsx3CCV15MinBucket
The number of C-bit Coding Violations(CCV)
encountered by the interface in last
15 minute period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.42
dsx3CCV24HrBucket
The number of C-bit Coding Violations(CCV)
encountered by the interface in last
24 Hour period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.43
dsx3CESCurrent
The number of C-bit Errored Seconds(CES)
encountered by the interface in current
15 minute period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.44
dsx3CES15MinBucket
The number of C-bit Errored Seconds(CES)
encountered by the interface in last
15 minute period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.45
dsx3CES24HrBucket
The number of C-bit Errored Seconds(CES)
encountered by the interface in last
24 Hour period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.46
dsx3CSESCurrent
The number of C-bit Severely Errored Seconds(CSES)
encountered by the interface in current 15 minute period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.47
dsx3CSES15MinBucket
The number of C-bit Severely Errored Seconds(CSES)
encountered by the interface in last 15 minute period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.48
dsx3CSES24HrBucket
The number of C-bit Severely Errored Seconds(CSES)
encountered by the interface in last 24 Hour period.

This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.3.1.1.49

dsx3CounterTable

table
.1.3.6.1.4.1.351.110.4.4.1.4.1 · 1 row entry · 13 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk dsx3CounterTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-MGX82XX-DSX3-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-MGX82XX-DSX3-MIB::dsx3CounterTable' 
This table is for ds3/e3 statistics. This table
maintains the number of times the line encountered
LOS, LOF, AIS, RAI, CCV and Framing Errors(FE)
from the time it is up. Error statistics are
cleared when the line is brought up from the failure
state.
dsx3CounterEntry row .1.3.6.1.4.1.351.110.4.4.1.4.1.1
An entry in the table. Statistics are gathered
for each ds3/e3 interface. An entry is created
automatically for each ds3/e3 interface that
is activated.
Indexes
Column Syntax OID
dsx3RcvLOSCount
The number of times the Loss of Signal was detected
with or without integrating to LOS alarm.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.4.1.1.1
dsx3RcvOOFCount
The number of times the Out of Frame was detected
with or without integrating to OOF alarm.
This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.4.1.1.2
dsx3RAICount
The number of times Yellow Alarms was detected with
or without integrating to RAI alarm.
This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.4.1.1.3
dsx3CCVCount
The counter associated with the number of C Bit
Coding Violations encountered by a DS3/E3 interface.
This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.4.1.1.4
dsx3FECount
The number of Framing Pattern Errors encountered by
a DS3/E3 interface.
This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.4.1.1.5
dsx3AtmHECCount
The number of Header Check Sequence(HCS) Errors.
This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.4.1.1.6
dsx3AtmHECSecCount
The number of HEC errored seconds.
This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.4.1.1.7
dsx3AtmSEHECSecCount
The number of Severely HEC error seconds.
This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.4.1.1.8
dsx3CounterClrButton
This variable is used to clear all the counters.
Enumerationr/w
Enumerated Values:
1noAction
2clear
 .1.3.6.1.4.1.351.110.4.4.1.4.1.1.9
dsx3RcvPERRCounter
The number of P-bit parity error.
This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.4.1.1.10
dsx3RcvFEBECounter
The number of Far-end block error.
This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.4.1.1.11
dsx3RcvEXZCounter
The number of excessive zeros
This object is not supported in CESM-T3/E3
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.4.1.1.12
dsx3LCVCount
The counter associated with the number of Line
Coding Violations encountered by a DS3/E3 interface.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.1.4.1.1.13

dsx3PlcpConfigTable

table
.1.3.6.1.4.1.351.110.4.4.2.1.1 · 1 row entry · 4 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk dsx3PlcpConfigTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-MGX82XX-DSX3-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-MGX82XX-DSX3-MIB::dsx3PlcpConfigTable' 
This table contains ATM interface DS3 PLCP
configuration parameters.
dsx3PlcpConfigEntry row .1.3.6.1.4.1.351.110.4.4.2.1.1.1
An entry in the DSX3 PLCP Configuration table.
Indexes
Column Syntax OID
dsx3PlcpNum
This object identifies the dsx3 PLCP interface.
The value of this object must be same as the value
specified in 'dsx3LineNum' object from cwDsx3ConfigTable.
Integer32
Constraints:
range: 1-2147483647
 .1.3.6.1.4.1.351.110.4.4.2.1.1.1.1
dsx3PlcpCellFraming
The value for this object sets the cell delineation
method used by the interface. The cell delineation
defines how a receiving device recognizes the start
and end of an ATM cell.

framingByPlcp (1): The …
Enumeration
Enumerated Values:
1framingByPlcp
2framingbyAtmHec
 .1.3.6.1.4.1.351.110.4.4.2.1.1.1.2
dsx3PlcpPayloadScramble
The value for this object is used for enabling/disabling
PLCP cell scrambling.
Enumerationr/w
Enumerated Values:
1enableScrambling
2disableScrambling
 .1.3.6.1.4.1.351.110.4.4.2.1.1.1.3
dsx3PlcpLoopCommand
specifies the type of loopback on the line.

The possible value(s) are :
noLoop (1): Not in loopback.
remoteLineLoop (2): Remote Line Loopback.
localLineLoop (3): Local Line Loopback.
Enumerationr/w
Enumerated Values:
1noLoop
2remoteLineLoop
3localLineLoop
 .1.3.6.1.4.1.351.110.4.4.2.1.1.1.4

dsx3PlcpAlarmConfigTable

table
.1.3.6.1.4.1.351.110.4.4.2.2.1 · 1 row entry · 18 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk dsx3PlcpAlarmConfigTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-MGX82XX-DSX3-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-MGX82XX-DSX3-MIB::dsx3PlcpAlarmConfigTable' 
This table contains the ATM interface PLCP alarm
parameters.
dsx3PlcpAlarmConfigEntry row .1.3.6.1.4.1.351.110.4.4.2.2.1.1
An entry in the DSX3 PLCP Alarm Configuration table.

Thresholds may be configured for:

Errored Seconds (ES)
Coding Violations (CV)
Severely Errored Seconds (SES)
…
Indexes
Column Syntax OID
dsx3PlcpRedSeverity
This variable is used to setup the severity of PLCP RED
alarm. So when PLCP_OOF alarm is detected the card will
declare the alarm with appropriate severity status.
A major alarm will cause the audible notification
and t…
Enumerationr/w
Enumerated Values:
1minor
2major
 .1.3.6.1.4.1.351.110.4.4.2.2.1.1.1
dsx3PlcpRAISeverity
This variable is used to setup the severity of
PLCP RAI alarm. So when PLCP RAI alarm is detected
the card will send the alarm with appropriate severity
status.
A major alarm will cause the audible notification
and t…
Enumerationr/w
Enumerated Values:
1minor
2major
 .1.3.6.1.4.1.351.110.4.4.2.2.1.1.2
dsx3PlcpLssSeverity
This variable is used to setup the severity of
PLCP RAI alarm. So when PLCP LSS alarm is detected
the card will send the alarm with appropriate severity
status.
A major alarm will cause the audible notification
and th…
Enumerationr/w
Enumerated Values:
1minor
2major
 .1.3.6.1.4.1.351.110.4.4.2.2.1.1.3
dsx3PlcpLssEnable
This objects specifies whether the LSS feature is
enabled/disabled.
Enumerationr/w
Enumerated Values:
1lssEnable
2lssDisable
 .1.3.6.1.4.1.351.110.4.4.2.2.1.1.4
dsx3PlcpLssCodeConnected
This object derfines the value of the LSS code
that is to be interpreted as Link Connected.
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.2.2.1.1.5
dsx3PlcpLssCodeRxLinkDn
This object defines the value of the LSS code
that is to be identified as Receive Link Down.
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.2.2.1.1.6
dsx3PlcpLssCodeRxLinkUp
This object defines the value of the LSS code that
is to be interpreted as Receive Link Up.
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.2.2.1.1.7
dsx3PlcpStatisticalAlarmSeverity
This variable sets up the severity of PLCP Statistical
alarm. So when PLCP Statistical alarm is detected, the
card will send the alarm with appropriate severity.
A major alarm will cause the audible notification
and th…
Enumerationr/w
Enumerated Values:
1minor
2major
 .1.3.6.1.4.1.351.110.4.4.2.2.1.1.8
dsx3PlcpBip8CV15MinThreshold
The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.2.2.1.1.9
dsx3PlcpBip8CV24HrThreshold
The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interv…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.2.2.1.1.10
dsx3PlcpBip8ES15MinThreshold
The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.2.2.1.1.11
dsx3PlcpBip8ES24HrThreshold
The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.2.2.1.1.12
dsx3PlcpBip8SES15MinThreshold
The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.2.2.1.1.13
dsx3PlcpBip8SES24HrThreshold
The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interv…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.2.2.1.1.14
dsx3PlcpSEFS15MinThreshold
The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.2.2.1.1.15
dsx3PlcpSEFS24HrThreshold
The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.2.2.1.1.16
dsx3PlcpUAS15MinThreshold
The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.2.2.1.1.17
dsx3PlcpUAS24HrThreshold
The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.2.2.1.1.18

dsx3PlcpAlarmTable

table
.1.3.6.1.4.1.351.110.4.4.2.3.1 · 1 row entry · 18 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk dsx3PlcpAlarmTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-MGX82XX-DSX3-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-MGX82XX-DSX3-MIB::dsx3PlcpAlarmTable' 
This table contains ATM interface DS3 PLCP
alarm configuration.
dsx3PlcpAlarmEntry row .1.3.6.1.4.1.351.110.4.4.2.3.1.1
An entry in the ATM DS3 PLCP alarm table.
Bucket statistics (15 minute and 24 Hour interval)
are gathered for each ds3/e3 interface automatically.
Indexes
Column Syntax OID
dsx3PlcpLineAlarmState
This variable is a bitmap of the DSX3 Line alarms.
A value of zero indicates no alarms.

Itemized below are the individual bits:

BitPosition Alarm
----------- -----
0 …
Integer32
Constraints:
range: 0-511
 .1.3.6.1.4.1.351.110.4.4.2.3.1.1.1
dsx3PlcpLineStatisticalAlarmState
This variable is a bitmap of the DSX3 Line Statictical
Alarms on the card. A value of zero indicates no alarms.

Itemized below are the individual alarm bits:

BitPosition Alarm
----------…
Integer32
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.110.4.4.2.3.1.1.2
dsx3PlcpBip8CVCurrent
This counter counts the number of
BIP-8 code violations encountered by the interface.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.3.1.1.3
dsx3PlcpBip8CV15MinBucket
The counter associated with the number of
BIP-8 code violations in the last 15 minute period
encountered by the interface.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.3.1.1.4
dsx3PlcpBip8CV24HrBucket
The counter associated with the number of
BIP-8 code violations in the last 24 hour period
encountered by the interface.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.3.1.1.5
dsx3PlcpBip8ESCurrent
This counter counts the number of
BIP-8 code violations Errored Seconds
encountered by the interface.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.3.1.1.6
dsx3PlcpBip8ES15MinBucket
This counter counts the number of
BIP-8 code violations Errored Seconds in the
last 15 minutes encountered by the interface.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.3.1.1.7
dsx3PlcpBip8ES24HrBucket
This counter counts the number of
BIP-8 code violations Errored Seconds in the
last 24 hours encountered by the interface.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.3.1.1.8
dsx3PlcpBip8SESCurrent
This counter counts the number of
Bip8 code violations Severely Errored Seconds
encountered by the interface.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.3.1.1.9
dsx3PlcpBip8SES15MinBucket
This counter counts the number of
BIP-8 Severely Errored Seconds in the last
15 minutes encountered by the interface.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.3.1.1.10
dsx3PlcpBip8SES24HrBucket
This counter counts the number of
BIP-8 Severely Errored Seconds in the last
24 hours encountered by the interface.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.3.1.1.11
dsx3PlcpSEFSCurrent
This counter counts the number of
Severely Errored Framing Seconds
encountered by the interface.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.3.1.1.12
dsx3PlcpSEFS15MinBucket
This counter counts the number of
Severely Errored Framing Seconds in the last
15 minutes encountered by the interface.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.3.1.1.13
dsx3PlcpSEFS24HrBucket
This counter counts the number of
Severely Errored Framing Seconds in the last
24 hours encountered by the interface.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.3.1.1.14
dsx3PlcpUASCurrent
This counter counts the number of
Unavailable Seconds encountered by the interface.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.3.1.1.15
dsx3PlcpUAS15MinBucket
This counter counts the number of
Unavailable Seconds in the last 15 minutes
encountered by the interface.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.3.1.1.16
dsx3PlcpUAS24HrBucket
This counter counts the number of
Unavailable Seconds in the last 24 hours
encountered by the interface.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.3.1.1.17
dsx3PlcpAlarmClrButton
This variable is used to clear all the alarms.
Enumerationr/w
Enumerated Values:
1dsx3PlcpAlarmNoAction
2dsx3PlcpAlarmClear
 .1.3.6.1.4.1.351.110.4.4.2.3.1.1.18

dsx3PlcpCounterTable

table
.1.3.6.1.4.1.351.110.4.4.2.4.1 · 1 row entry · 13 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk dsx3PlcpCounterTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-MGX82XX-DSX3-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-MGX82XX-DSX3-MIB::dsx3PlcpCounterTable' 
The table for DS3 PLCP counter table.
dsx3PlcpCounterEntry row .1.3.6.1.4.1.351.110.4.4.2.4.1.1
An entry in the DS3 PLCP counter table.
Indexes
Column Syntax OID
dsx3PlcpRcvBip8Count
The number of BIP-8 errors encountered by
the interface.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.4.1.1.1
dsx3PlcpRcvOOFCount
The number of times the Out of Frame(OOF) was detected
with or without integrating to OOF alarm.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.4.1.1.2
dsx3PlcpRcvRAICount
The number of times Remote Alarm Indication(RAI)
was detected with or without integrating to RAI alarm.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.4.1.1.3
dsx3PlcpFECount
The number of Framing Errors detected.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.4.1.1.4
dsx3PlcpFESecCount
The number of Framing Error errored seconds.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.4.1.1.5
dsx3PlcpSEFESecCount
The number of Severely errored Framing error seconds.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.4.1.1.6
dsx3PlcpFEBECount
The number of Far End Block Errors(FEBE) detected.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.4.1.1.7
dsx3PlcpFEBESecCount
The number of FEBE errored seconds.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.4.1.1.8
dsx3PlcpSEFEBESecCount
The number of Severely errored FEBE seconds.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.4.1.1.9
dsx3PlcpHECCount
The number of HCS Errors.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.4.1.1.10
dsx3PlcpHECSecCount
The number of HEC errored seconds.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.4.1.1.11
dsx3PlcpSEHECSecCount
The number of Severely HEC error seconds.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.351.110.4.4.2.4.1.1.12
dsx3PlcpCounterClrButton
This variable is used to clear all the counters.
Enumerationr/w
Enumerated Values:
1dsx3PlcpCounterNoAction
2dsx3PlcpCounterClear
 .1.3.6.1.4.1.351.110.4.4.2.4.1.1.13