WESTERMO-SW6-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
44
Rows
44
Columns
415

cfgNetEthernetTable

table
.1.3.6.1.4.1.16177.1.400.1.1.2.1 · 1 row entry · 10 columns
Open in standard view 
Ethernet Network Interfaces.
cfgNetEthernetTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.2.1.1
Ethernet Network Interfaces.
Indexes
cfgNetEthIndex
Column Syntax OID
cfgNetEthIndex
Entry index of table.
Integer32
Constraints:
range: 0-9
 .1.3.6.1.4.1.16177.1.400.1.1.2.1.1.1
cfgNetEthName
Name of the ethernet interface.

Applies to AP and STA.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.2.1.1.2
cfgNetEthEnabled
Ethernet interface disabled or enabled.

Applies to AP and STA.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.2.1.1.3
cfgNetEthBridge
If set to other than -1 the interface is part of bridge:

* -1: none
* 0: br0
* 1: br1
* X: brX

Bridges with an index >=100 are special bridges which forward
link local traffic. This can be …
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.2.1.1.7
cfgNetEthAutoneg
Enables or disables auto negotiation of the PHY.

* **forced(0):** Forces the speed and duplex defined by
`cfgNetEthSpeed`. Only 10Mbit and 100Mbit rates are
allowed in forced mode. 1000Mbit requires …
Enumerationr/w
Enumerated Values:
0forced
1auto
 .1.3.6.1.4.1.16177.1.400.1.1.2.1.1.8
cfgNetEthSpeed
Defines a bitmask containing the possible speed/duplex combinations.

* 0x01 (1) = 10Mbit/Half
* 0x02 (2) = 10Mbit/Full
* 0x04 (4) = 100Mbit/Half
* 0x08 (8) = 100Mbit/Full
* 0x20 (32) = 1000Mbit/Full
…
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.2.1.1.9
cfgNetEthTrunk
This entry is active when `cfgNetEthVlanMode` is set to
**trunk(0)** or **nativeuntagged(3)**.

It specifies which 802.1q vlans are accepted ingress and egress on
the respective port. All unspecified vlans…
OctetStringr/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.2.1.1.10
cfgNetEthTag
This entry is active when `cfgNetEthVlanMode` is set to
**access(1)** or **nativeuntagged(3)**. It specifies which 802.1q
VLAN should be used for untagged ingress and egress traffic. Set
this entry to -1 to disable it.
…
Integer32r/w
Constraints:
range: -1-4094
 .1.3.6.1.4.1.16177.1.400.1.1.2.1.1.11
cfgNetEthVlanMode
This entry specifies how the port should behave.

* **trunk(0):** A trunk port carries packets on one or more specified
VLANs specified in the cfgNetEthTrunk entry.
A packet that ingresses on a trunk p…
Enumerationr/w
Enumerated Values:
0trunk
1access
3nativeuntagged
 .1.3.6.1.4.1.16177.1.400.1.1.2.1.1.12
cfgNetEthLldpEnabled
When `cfgLldpEnabled` is enabled, this parameter controls if
the interface takes part in LLDP operation.

Applies to AP and STA.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.2.1.1.15

cfgNetWlanTable

table
.1.3.6.1.4.1.16177.1.400.1.1.2.2 · 1 row entry · 8 columns
Open in standard view 
WLAN Network Interfaces.
cfgNetWlanTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.2.2.1
WLAN Network Interfaces.
Indexes
cfgNetWlanIndex
Column Syntax OID
cfgNetWlanIndex
Entry index of Table.
Integer32
Constraints:
range: 0-63
 .1.3.6.1.4.1.16177.1.400.1.1.2.2.1.1
cfgNetWlanName
Name of the wireless interface.

Applies to AP and STA.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.2.2.1.2
cfgNetWlanEnabled
Wireless interface disabled or enabled.

Applies to AP and STA.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.2.2.1.3
cfgNetWlanBridge
If set to other than -1 the interface is part of bridge:

* -1: none
* 0: br0
* 1: br1
* X: brX

Bridges with an index >=100 are special bridges which forward
link local traffic. This can be …
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.2.2.1.7
cfgNetWlanTrunk
This entry is active when `cfgNetWlanVlanMode` is set to
**trunk(0)** or **nativeuntagged(3)**.

It specifies which 802.1q vlans are accepted ingress and egress on
the respective port. All unspecified vlan…
OctetStringr/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.2.2.1.10
cfgNetWlanTag
This entry is active when `cfgNetWlanVlanMode` is set to
**access(1)** or **nativeuntagged(3)**. It specifies which 802.1q
VLAN should be used for untagged ingress and egress traffic. Set
this entry to -1 to disable it.…
Integer32r/w
Constraints:
range: -1-4094
 .1.3.6.1.4.1.16177.1.400.1.1.2.2.1.11
cfgNetWlanVlanMode
This entry specifies how the port should behave.

* **trunk(0):** A trunk port carries packets on one or more specified
VLANs specified in the cfgNetWlanTrunk entry.
A packet that ingresses on a trunk …
Enumerationr/w
Enumerated Values:
0trunk
1access
3nativeuntagged
 .1.3.6.1.4.1.16177.1.400.1.1.2.2.1.12
cfgNetWlanLldpEnabled
When `cfgLldpEnabled` is enabled, this parameter controls if
the interface takes part in LLDP operation.

Applies to AP and STA.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.2.2.1.15

cfgNetVlanTable

table
.1.3.6.1.4.1.16177.1.400.1.1.2.3 · 1 row entry · 6 columns
Open in standard view 
VLAN Network Interfaces.
cfgNetVlanTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.2.3.1
VLAN Network Interfaces.
Indexes
cfgNetVlanIndex
Column Syntax OID
cfgNetVlanIndex
Entry index of table.
Integer32
Constraints:
range: 0-127
 .1.3.6.1.4.1.16177.1.400.1.1.2.3.1.1
cfgNetVlanName
Name of the VLAN interface.

Applies to AP and STA.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.2.3.1.2
cfgNetVlanEnabled
VLAN interface disabled or enabled.

Applies to AP and STA.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.2.3.1.3
cfgNetVlanBridge
The number of the bridge the VLAN interface is applied to.

VLAN interfaces are always of type access.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.2.3.1.7
cfgNetVlanParent
Name of the physical parent interface on which the VLAN resides.

This entry is only active when the VLAN interface is not part of
a bridge (cfgNetVlanBridge = -1).

Applies to AP and STA.
OctetStringr/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.2.3.1.8
cfgNetVlanVid
ID of the VLAN.

Applies to AP and STA.
Integer32r/w
Constraints:
range: 0-4094
 .1.3.6.1.4.1.16177.1.400.1.1.2.3.1.9

cfgNetIpTable

table
.1.3.6.1.4.1.16177.1.400.1.1.2.6 · 1 row entry · 6 columns
Open in standard view 
IP address configuration.
cfgNetIpTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.2.6.1
IP address configuration.
Indexes
cfgNetIpIndex
Column Syntax OID
cfgNetIpIndex
Entry index of table.
Integer32
Constraints:
range: 0-127
 .1.3.6.1.4.1.16177.1.400.1.1.2.6.1.1
cfgNetIpEnabled
IP disabled or enabled.

Applies to AP and STA.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.2.6.1.3
cfgNetIpAddr
The IPv4 address (using CIDR notation) of the interface specified
in cfgNetIpInterface.

Applies to AP and STA.
OctetStringr/w
Constraints:
range: 9-19
 .1.3.6.1.4.1.16177.1.400.1.1.2.6.1.4
cfgNetIpProto
This parameter defines which protocol is used to get the IPv4
settings for this interface.

* **static(0):** Indicates that the address is manually configured to a
specified address given by the IPv4 add…
Enumerationr/w
Enumerated Values:
0static
1dhcp
2dhcpForceRenew
3dhcpForceRelease
4linkLocal
5carp
 .1.3.6.1.4.1.16177.1.400.1.1.2.6.1.6
cfgNetIpInterface
Name of the interface on which the IP resides.

Applies to AP and STA.
OctetStringr/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.2.6.1.8
cfgNetIpCarpId
Id which references the CARP-instance by `cfgNetCarpIndex`.

This parameter is only active when `cfgNetIpProto` is set to carp(5).
Indicates that the referenced CARP instance processes this IP.
…
Integer32r/w
Constraints:
range: 0-15
 .1.3.6.1.4.1.16177.1.400.1.1.2.6.1.10

cfgNetCarpTable

table
.1.3.6.1.4.1.16177.1.400.1.1.2.7 · 1 row entry · 13 columns
Open in standard view 
Redundant IP Addresses with the Common Address Redundancy Protocol (CARP).
cfgNetCarpTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.2.7.1
Redundant IP Addresses with the Common Address Redundancy Protocol (CARP).
Indexes
cfgNetCarpIndex
Column Syntax OID
cfgNetCarpIndex
Entry index of Table.
Integer32
Constraints:
range: 0-15
 .1.3.6.1.4.1.16177.1.400.1.1.2.7.1.1
cfgNetCarpEnabled
CARP interface disabled or enabled.

Applies to AP and STA.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.2.7.1.3
cfgNetCarpVhid
The Virtual Host ID.

This is a unique number that is used to identify the redundancy
group to other nodes in the group, and to distinguish between
groups on the same network.

This must be t…
Integer32r/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.2.7.1.10
cfgNetCarpPassword
The CARP authentication password.

This is the password which is used to encrypt the CARP frames
when talking to other CARP-enabled hosts in this redundancy group.

This must be the same on a…
OctetStringr/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.2.7.1.11
cfgNetCarpAdvbase
Advertisement base in seconds.

This parameter specifies how often to transmit advertisement frames
that we're a member of the redundancy group.

This time is divided with `cfgNetCarpAdvdivid…
Integer32r/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.2.7.1.12
cfgNetCarpAdvskew
Advertisement base in 1/255th of a second.

This parameter specifies how much to skew the advbase when
sending CARP advertisements.

By manipulating advskew, the master of a CARP group can be…
Integer32r/w
Constraints:
range: 0-254
 .1.3.6.1.4.1.16177.1.400.1.1.2.7.1.13
cfgNetCarpAdvdivider
Divider for `cfgNetCarpAdvbase` and `cfgNetCarpAdvskew`.

This parameter specifies how much the Advbase and Advskew are
divided to speed the algorithm up. With a factor of 1, the
Advbase and Advskew are un…
Integer32r/w
Constraints:
range: 1-100
 .1.3.6.1.4.1.16177.1.400.1.1.2.7.1.14
cfgNetCarpRatio
The dead ratio after which an existing master is considered dead.

A slave device will wait:

`cfgNetCarpRatio` * (`cfgNetCarpAdvbase` + `cfgNetCarpAdvskew`)

before considering…
Integer32r/w
Constraints:
range: 1-100
 .1.3.6.1.4.1.16177.1.400.1.1.2.7.1.15
cfgNetCarpPreempt
Preempt other masters when the local device is better.

Allow hosts within a redundancy group that have a better Advbase
and Advskew to preempt the current master.

Applies to AP and STA.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.2.7.1.16
cfgNetCarpPreemptdemote
Preempt other master when they demote theself.

Allow hosts within a redundancy group that have a better Advbase
and Advskew to preempt the current master when it demotes itself
(skew >= 240).
…
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.2.7.1.17
cfgNetCarpLocalInterfaceGroup
The local carp interface group the carp interface belongs to.

When `cfgNetCarpPreempt` or `cfgNetCarpPreemptdemote` is set to
enabled, the interface will demote itself (skew = 240) when another
interface …
Integer32r/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.2.7.1.18
cfgNetCarpSyncInterface
Name of the CARP control interface.

This interface is used to transmit and receive CARP advertisements.

This interface is required to have its own unique IP address.

Applies …
OctetStringr/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.2.7.1.19
cfgNetCarpMcastIp
Multicast address on which CARP advertisments are transmitted.

The default multicast address for CARP is 224.0.0.18.

Use this parameter to specify a custom multicast destination.
…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.16177.1.400.1.1.2.7.1.21

cfgNetMacVlanTable

table
.1.3.6.1.4.1.16177.1.400.1.1.2.9 · 1 row entry · 5 columns
Open in standard view 
MACVLAN Network Interfaces.
cfgNetMacVlanTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.2.9.1
MACVLAN Network Interfaces.
Indexes
cfgNetMacVlanIndex
Column Syntax OID
cfgNetMacVlanIndex
Entry index of Table.
Integer32
Constraints:
range: 0-63
 .1.3.6.1.4.1.16177.1.400.1.1.2.9.1.1
cfgNetMacVlanName
Name of the MACVLAN interface.

Applies to AP and STA.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.2.9.1.2
cfgNetMacVlanEnabled
MACVLAN interface disabled or enabled.

Applies to AP and STA.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.2.9.1.3
cfgNetMacVlanParent
Name of the parent interface on which the MACVLAN resides.

Applies to AP and STA.
OctetStringr/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.2.9.1.8
cfgNetMacVlanMac
MAC address of the MACVLAN.
Set `00:00:00:00:00:00` to use a random MAC address.

**Format:** `00:14:5a:02:10:42`

Applies to AP and STA.
OctetStringr/w
Constraints:
range: 17-17
 .1.3.6.1.4.1.16177.1.400.1.1.2.9.1.15

cfgNetWwanTable

table
.1.3.6.1.4.1.16177.1.400.1.1.2.11 · 1 row entry · 5 columns
Open in standard view 
WWAN (Cellular) Network Interfaces.
          
Applies to LTE products only.
cfgNetWwanTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.2.11.1
WWAN (Cellular) Network Interfaces.

Applies to LTE products only.
Indexes
cfgNetWwanIndex
Column Syntax OID
cfgNetWwanIndex
Entry index of Table.

Applies to LTE products only.
Integer32
Constraints:
range: 0-1
 .1.3.6.1.4.1.16177.1.400.1.1.2.11.1.1
cfgNetWwanName
Name of the WWAN interface

Applies to LTE products only.
OctetString
Constraints:
range: 4-5
 .1.3.6.1.4.1.16177.1.400.1.1.2.11.1.2
cfgNetWwanEnabled
WWAN interface disabled or enabled

Applies to LTE products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.2.11.1.3
cfgNetWwanPrimarySim
SIM parameter entry for the primary SIM

This value references the `cfgCellSimIndex` of the desired entry in
the `cfgCellSimTable` for the primary SIM.

Applies to LTE products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.2.11.1.4
cfgNetWwanSecondarySim
SIM parameter entry for the secondary SIM

This value references the `cfgCellSimIndex` of the desired entry in
the `cfgCellSimTable` for the secondary SIM.

Applies to LTE products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.2.11.1.5

cfgWlanDeviceTable

table
.1.3.6.1.4.1.16177.1.400.1.1.3.1 · 1 row entry · 17 columns
Open in standard view 
Wireless Hardware Modules.
cfgWlanDeviceTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.3.1.1
Wireless Hardware Modules.
Indexes
cfgWlanDevIndex
Column Syntax OID
cfgWlanDevIndex
Entry index of table.
Integer32
Constraints:
range: 0-1
 .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.1
cfgWlanDevName
Name of the wireless device.

Applies to AP and STA.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.2
cfgWlanDevModulation
The modulation modes of the physical wireless device are:

* **g(2):** This modulation mode uses OFDM data rates up
to 54 MBit/s in the frequency band between 2.4 and 2.4835 GHz.
It supports the 802.1…
Enumerationr/w
Enumerated Values:
2g
3bg
4a
10ng
12na
28ac
 .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.4
cfgWlanDevBandwidth
Wireless Bandwidth Mode specifies the Bandwidth of the Channel.

* **bw20(0):** for 20MHz wide channel.
* **bw40Plus(1):** for 40MHz wide channel with the side
channel on the top.
* **bw40Minus(2):** for…
Enumerationr/w
Enumerated Values:
0bw20
1bw40Plus
2bw40Minus
3bwQuarter
4bwHalf
5bw80
6bw160
7bw8080
8bwAuto
 .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.5
cfgWlanDevFrequency
Wireless Frequency in MHz.

In AP mode, setting the wireless frequency to zero(0) enables the
automatic channel selection (ACS) feature. This forces the AP to choose
the best channel for operation.
…
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.6
cfgWlanDevPower
Max. limit for wireless output power as effective isotropic radiated power
(EIRP) in dBm including array gain and antenna gain.

**Note:** This parameter only limits the maximum output power. The effective…
Integer32r/w
Constraints:
range: 6-50
 .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.8
cfgWlanDevDistance
Maximum distance in meters a client can be apart from the access
point. Even though the distance is set in meters, the slot time
settings change in 450m steps.

Applies to AP and STA. 802.11n products only.
Integer32r/w
Constraints:
range: 0-114750
 .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.10
cfgWlanDevRts
Frames equal or longer in bytes than this value require a
RTS/CTS handshake.

RTS/CTS is used in hidden node situations. In 11bg and b mode,
these frames are sent in DSSS modulation at 11b data rates.
Othe…
Integer32r/w
Constraints:
range: -1-65535
 .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.11
cfgWlanDevFragments
Frames longer in bytes than this threshold will be fragmented.

Fragmentation can be used to reduce the number of retransmissions.
The following settings are special

* **-1** disable value, …
Integer32r/w
Constraints:
range: -1-2346
 .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.12
cfgWlanDevShortRetry
Number of times the transmission of the RTS frame will be retried
if there is no CTS received from the AP.

Applies to AP and STA. 802.11n products only.
Integer32r/w
Constraints:
range: 1-10
 .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.13
cfgWlanDevLongRetry
Number of times the unicast data frames will be retried if there is
no ACK from the receiver.

Applies to AP and STA. 802.11n products only.
Integer32r/w
Constraints:
range: 1-10
 .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.14
cfgWlanDevAntennaGain
Antenna gain in dBi.

If multiple antennas with different gains are connected, the value
of the antenna with the highest gain shall be configured.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.15
cfgWlanDevTxAntenna
Configure the number of wireless transmission antenna ports.

This is a bitmask to enable/disable the chains.

**Example**

* 1(0001) = A1 (chain 0) enabled
* 3(0011) = A1 and A…
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.16
cfgWlanDevRxAntenna
Configure the number of wireless receiver antennas.

This is a bitmask to enable/disable the chains.

**Example**

* 1(0001) = A1 (chain 0) enabled
* 3(0011) = A1 and A2 chain 0…
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.17
cfgWlanDevPhy
The map between physical device and radio.

Applies to AP and STA.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.18
cfgWlanDevHtCapabilities
HT capability flags:

* [LDPC] = 1 Enable support for LDPC coding
* [SHORT-GI-20] = 32 Allow short GI for 20 MHz
* [SHORT-GI-40] = 64 Allow short GI for 40 MHz
* [TX-STBC] =…
Integer32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.24
cfgWlanDevQmrrString
A list of rate controller quadruples per queue.

Each quadruple consist of
(mcs-rate [0-31], tries [0-15], rts_cts [0-1], sgi [0-1])
with 4 entries per queue.

16 values together are for a si…
SNMPv2-TCDisplayStringr/w
Textual Convention: SNMPv2-TCDisplayString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.26

cfgWlanInterfaceTable

table
.1.3.6.1.4.1.16177.1.400.1.1.3.2 · 1 row entry · 34 columns
Open in standard view 
Wireless Virtual Interfaces.
cfgWlanInterfaceTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.3.2.1
Wireless Virtual Interface Entry.
Indexes
cfgWlanIfaceIndex
Column Syntax OID
cfgWlanIfaceIndex
Entry index of table.
Integer32
Constraints:
range: 0-63
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.1
cfgWlanIfaceName
Name of the virtual wireless interface.

Applies to AP and STA.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.2
cfgWlanIfaceDevice
Maps the virtual wireless interface to the radio device.

Applies to AP and STA.
Enumerationr/w
Enumerated Values:
0radio0
1radio1
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.3
cfgWlanIfaceMode
Wireless Operation Mode.

Allowed modes are:

* **ap(0):** defines the interface as Access Point (AP)
* **sta(1):** defines the interface as Station (STA)
* **monitor(2):** defines the interf…
Enumerationr/w
Enumerated Values:
0ap
1sta
2monitor
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.4
cfgWlanIfaceSsid
The Service Set Identifier (SSID) of the wireless interface is the
arbitrary name of the wireless network this interface is part of.

Applies to AP and STA.
OctetStringr/w
Constraints:
range: 1-32
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.5
cfgWlanIfaceEncryption
Wireless Encryption Mode.

Following encryption modes are supported: **open(0)**, **wpa2(3)**,
**wpa2eap(6)** and **sae(7)**.

**Note:** WPA2 EAP enables 802.1X support.

**Note…
Enumerationr/w
Enumerated Values:
0open
3wpa2
6wpa2eap
7sae
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.6
cfgWlanIfacePassword
Wireless password if an encryption is in use.

Each character in the pass-phrase must have an
encoding in the range of 32 to 126 (decimal),
inclusive. (IEEE Std. 802.11i-2004, Annex H.4.1)
The space charac…
OctetStringr/w
Constraints:
range: 8-63
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.7
cfgWlanIfacePassiveScanning
Wireless Scanning Mode.

If the scanning mode is set to active(0) the station will send
a probe request to detect available access points if it's allowed
by the country code.

If the scanning…
Enumerationr/w
Enumerated Values:
0active
1passive
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.8
cfgWlanIfaceBeaconMiss
Number of misses on consecutive beacons before the station will
disconnect from the associated access point.

Applies to STA. 802.11n products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.9
cfgWlanIfaceDtim
This attribute shall specify the number of beacon intervals that
shall elapse between transmission of beacons frames containing a
TIM element whose DTIM count field is 0. This value is transmitted
in the DTIM Period fie…
Integer32r/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.10
cfgWlanIfaceBitrates
Fixed MCS index for 802.11n rates.

Set to -1 to disable (leave on auto). Allows for entering multiple
indices divided by a space which are then used in auto rate.
This entry is only active when an n-rate …
SNMPv2-TCDisplayStringr/w
Textual Convention: SNMPv2-TCDisplayString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.11
cfgWlanIfaceBeaconInterval
Time in kus (1.024 ms) between the sending of beacon frames.

Applies to AP. 802.11n products only.
Integer32r/w
Constraints:
range: 15-1000
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.12
cfgWlanIfaceWmeParameter
Reference ID to the WME parameter table.

Uses all parameters in the cfgWlanWmeTable which have as
cfgWlanWmeId the value set here.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.13
cfgWlanIfaceWmeEnabled
Enables usage of the WME parameter table.

When using legacy rates (a-rates and g-rates) this is optional.
When using n-rates this has to be enabled at all times.

Applies to AP. 802.11n prod…
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.14
cfgWlanIfaceScanList
Index to specify a frequency list with frequencies to be scanned
when in STA mode. To only scan the frequency defined in
cfgWlanDevFrequency set to -1. To scan all frequencies allowed by
the configured country code set …
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.15
cfgWlanIfaceIgnoreBroadcastSsid
Send empty SSID in beacons and ignore probe request frames that
do not specify the full SSID, i.e., require stations to know SSID.

Applies to AP.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.16
cfgWlanIfaceMacaddrAcl
Mode of the MAC access control list.

* **acceptunlessdeny(0):** Accept unless deny filter. Accept
every MAC unless it is on the list defined in
`cfgWlanAclBlackTable`.
* **denyunlessaccept(1):** Deny …
Enumerationr/w
Enumerated Values:
0acceptunlessdeny
1denyunlessaccept
2radius
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.17
cfgWlanIfaceMaxNumSta
Maximum number of allowed stations which can connect to this AP.

Applies to AP. 802.11n products only.
Integer32r/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.18
cfgWlanIfaceBssid
BSSID of AP.

Set 00:00:00:00:00:00 to use the MAC address stored in the flash of
the wireless card itself. If this is the second virtual AP on this
card it will automatically set the locally assigned bit.…
OctetStringr/w
Constraints:
range: 17-17
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.19
cfgWlanIfaceLegacyRates
Wireless legacy data rates:

* **11b:** 1, 2, 5.5, 11 Mbps
* **11a/g:** 6, 9, 12, 18, 24, 36, 48, 54 Mbps

The values are interpreted as flags:

* auto(0), 1Mbps(1), 2Mbps(2), 5…
Integer32r/w
Constraints:
range: 0-2048
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.20
cfgWlanIface4addr
This option allows to bridge the STA side.

When used on the STA, the corresponding AP has to enable this
feature as well.

Applies to AP and STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.21
cfgWlanIfaceInactivityTimeout
If a station does not send anything in ap_max_inactivity seconds,
an empty data frame is sent to it in order to verify whether it is
still in range. If this frame is not ACKed, the station will be
disassociated and then…
Integer32r/w
Constraints:
range: 15-65535
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.23
cfgWlanIfaceUseVendorSsid
When cfgWlanIfaceIgnoreBroadcastSsid is enabled, a passively
scanning STA (forced or because of DFS) has no way of detecting
the AP it tries to find. On an AP this options adds the hidden
SSID as vendor element. On a ST…
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.26
cfgWlanIfaceIeee80211w
Controls usage of 802.11w Management Frame Protection (MFP)
mechanism. If set to optional on AP, MFP will be enabled only
for clients which have it also enabled. If set to required, only
MFP enabled clients will be able…
Enumerationr/w
Enumerated Values:
0disabled
1optional
2required
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.30
cfgWlanIfaceIeee80211wMaxTimeout
802.11w Management Frame Protection (MFP)

Association SA query maximum timeout (in TU = 1.024 ms; for MFP)
(maximum time to wait for a SA query response)

Applies to AP.
Integer32r/w
Constraints:
range: 1-4000
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.31
cfgWlanIfaceIeee80211wRetryTimeout
802.11w Management Frame Protection (MFP)

Association SA query retry timeout (in TU = 1.024 ms; for MFP)
(time between two subsequent SA query requests)

Applies to AP.
Integer32r/w
Constraints:
range: 1-4000
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.32
cfgWlanIfaceAcsList
Index to specify a frequency list for Automated Channel Selection
(ACS) support when in AP mode. To disable set to -1.

Applies to AP. 802.11n products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.40
cfgWlanIfaceNeighbourReport
Enable/disable neighbour reporting.

A STA can request the neighbour table from an AP and use this
information to improve its handoff decision.

Applies to AP. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.60
cfgWlanIfaceNeighbourParameter
Reference ID to the neighbour table. Uses all neighbours in the
`cfgWlanNeighbourTable` which have as `cfgWlanNeighbourId` the value set here.

Applies to AP. 802.11n products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.61
cfgWlanIfaceL2nat
This option allows to bridge the STA side.

It is intended to be used in setups where the STA is doing
handoff between multiple APs. There is no configuration on the APs
required. This is an alternative to…
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.80
cfgWlanIfaceL2natLearningMode
From which type of frames the IP/MAC table may be learned.

When `cfgWlanIfaceL2nat` is enabled a table of the association
between IP-addresses and MAC-addresses is kept. This options
specifies from which …
Enumerationr/w
Enumerated Values:
0both
1arp
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.81
cfgWlanIfaceL2natDefaultDestination
This option defines the default MAC address to send frames to.

Whenever a unicast frame is received for which no learned entry
exists, or which isn't a L3 frame (e.g a custom L2 protocol), the
frame will …
OctetStringr/w
Constraints:
range: 17-17
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.82
cfgWlanIfaceTimeAdvertisement
Enable AP to include local time in association response frames.

This provides a mean for APs to distribute its local system
time to STAs in setups where devices have no RTC and start
up with an invalid sy…
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.90
cfgWlanIfaceApIsolate
Enable AP clients isolation.

If enabled, clients connected to this AP can't communicate
to each other.

Applies to AP.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.2.1.100

cfgWlanHandoffTable

table
.1.3.6.1.4.1.16177.1.400.1.1.3.3 · 1 row entry · 19 columns
Open in standard view 
Wireless handoff parameters.
          
Applies to STA.  802.11n products only.
cfgWlanHandoffTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.3.3.1
Wireless handoff parameters entry.

Applies to STA. 802.11n products only.
Indexes
cfgWlanHoIndex
Column Syntax OID
cfgWlanHoIndex
Entry index of table.

Applies to STA. 802.11n products only.
Integer32
Constraints:
range: 0-63
 .1.3.6.1.4.1.16177.1.400.1.1.3.3.1.1
cfgWlanHoIfaceName
Name of the virtual wireless interface.

Applies to STA. 802.11n products only.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.3.3.1.2
cfgWlanHoProfile
Handoff profile.

* **t2gv1(1):** Train to Ground v1
* **t2gv2(2):** Train to Ground v2
* **t2gv2fg(3):** Train to Ground v2 fg scan
* **t2gv3(4):** Train to Ground v3 (RSSI high/low, Distance near/far)
…
Enumerationr/w
Enumerated Values:
1t2gv1
2t2gv2
3t2gv2fg
4t2gv3
 .1.3.6.1.4.1.16177.1.400.1.1.3.3.1.3
cfgWlanHoScanningLevel
Scanning level in RSSI.

When the RSSI level of the currently connected access point drops
below the value configured in this parameter, the STA will scan
for better access points on all frequencies specif…
Integer32r/w
Constraints:
range: 0-95
 .1.3.6.1.4.1.16177.1.400.1.1.3.3.1.5
cfgWlanHoBeacons
Number of beacons which have to be received from an AP before a
decision about handoff is allowed. Essentially forces the STA to
stay on a given AP for <cfgWlanHoBeacons * cfgWlanIfaceBeaconInterval>
before doing anothe…
Integer32r/w
Constraints:
range: 4-20
 .1.3.6.1.4.1.16177.1.400.1.1.3.3.1.6
cfgWlanHoRecovery
Recovery time in milliseconds after a successful handoff.

During this time no further handoff will be executed.

Applies to STA. 802.11n products only.
Integer32r/w
Constraints:
range: 0-2000
 .1.3.6.1.4.1.16177.1.400.1.1.3.3.1.7
cfgWlanHoFilterMode
RSSI filter mode.

* **short(0):** high responsive static IIR RSSI filter.
* **long(1):** configurable IIR RSSI filter.

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0short
1long
 .1.3.6.1.4.1.16177.1.400.1.1.3.3.1.9
cfgWlanHoFilterLongX
IIR Filter Parameter x for long RSSI filter.

Applies to STA. 802.11n products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.3.1.10
cfgWlanHoFilterLongY
IIR Filter Parameter y for long RSSI filter.

Applies to STA. 802.11n products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.3.1.11
cfgWlanHoScanRateLimitTime
Time in milliseconds (4ms steps) in which a number of attempts to connect
to an AP can be tried.

Applies to STA. 802.11n products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.3.1.12
cfgWlanHoScanRateLimitTries
Number of attempts to connect to an AP before the AP is blacklisted
and ignored. The AP is removed from the blacklist after
`cfgWlanHoScanRateLimitTime` since the first attempt.

Applies to STA. 802.11n pr…
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.3.1.13
cfgWlanHoPassiveChanTime
Time in milliseconds (4ms steps) we stay on a channel during passive
scanning and wait for beacons.

Applies to STA. 802.11n products only.
Integer32r/w
Constraints:
range: 1-65535
 .1.3.6.1.4.1.16177.1.400.1.1.3.3.1.16
cfgWlanHoLevelLow
Scanning level low in RSSI.

When the RSSI level to the current connected AP is below this value,
perform a handoff to the next AP.

This value is only active when `cfgWlanHoProfile` is set t…
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.3.1.18
cfgWlanHoLevelHigh
Scanning level high in RSSI.

When the RSSI level to the current connected AP is above this value,
perform a handoff to the next AP.

This value is only active when `cfgWlanHoProfile` is set …
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.3.1.19
cfgWlanHoDistanceNear
Distance level near.

When the measured distance to the current connected AP is below
this value in meters, perform a handoff to the next AP.

This value is only active when `cfgWlanHoProfile…
Integer32r/w
Constraints:
range: 0-114750
 .1.3.6.1.4.1.16177.1.400.1.1.3.3.1.20
cfgWlanHoDistanceFar
Distance level far.

When the measured distance to the current connected AP is above
this value in meters, perform a handoff to the next AP.

This value is only active when `cfgWlanHoProfile`…
Integer32r/w
Constraints:
range: 0-114750
 .1.3.6.1.4.1.16177.1.400.1.1.3.3.1.21
cfgWlanHoDistanceMeasurementPeriod
Distance ranging measurement period in milliseconds.

Setting zero disables distance handoff. This value is only active
when `cfgWlanHoProfile` is set to T2Gv3.

Typical ranging measurement p…
Integer32r/w
Constraints:
range: 0-100000
 .1.3.6.1.4.1.16177.1.400.1.1.3.3.1.22
cfgWlanHoDistanceFilterX
IIR Filter Parameter x for distance measurement.

This value is only active when `cfgWlanHoProfile` is set to T2Gv3.

Applies to STA. 802.11n products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.3.1.23
cfgWlanHoDistanceFilterY
IIR Filter Parameter y for distance measurements.

This value is only active when `cfgWlanHoProfile` is set to T2Gv3.

Applies to STA. 802.11n products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.3.1.24

cfgWlanFreqTable

table
.1.3.6.1.4.1.16177.1.400.1.1.3.4 · 1 row entry · 25 columns
Open in standard view 
Frequency list entry.
cfgWlanFreqTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.3.4.1
Frequency list entry.
Indexes
cfgWlanFIndex
Column Syntax OID
cfgWlanFIndex
Entry index of table
Integer32
Constraints:
range: 0-23
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.1
cfgWlanFFreq0
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.2
cfgWlanFFreq1
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.3
cfgWlanFFreq2
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.4
cfgWlanFFreq3
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.5
cfgWlanFFreq4
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.6
cfgWlanFFreq5
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.7
cfgWlanFFreq6
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.8
cfgWlanFFreq7
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.9
cfgWlanFFreq8
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.10
cfgWlanFFreq9
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.11
cfgWlanFFreq10
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.12
cfgWlanFFreq11
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.13
cfgWlanFFreq12
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.14
cfgWlanFFreq13
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.15
cfgWlanFFreq14
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.16
cfgWlanFFreq15
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.17
cfgWlanFFreq16
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.18
cfgWlanFFreq17
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.19
cfgWlanFFreq18
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.20
cfgWlanFFreq19
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.21
cfgWlanFFreq20
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.22
cfgWlanFFreq21
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.23
cfgWlanFFreq22
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.24
cfgWlanFFreq23
Frequency in MHz, 0 is interpreted as empty.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.4.1.25

cfgWlanWmeTable

table
.1.3.6.1.4.1.16177.1.400.1.1.3.5 · 1 row entry · 11 columns
Open in standard view 
Wireless Multimedia Extensions (WME) based on the IEEE 802.11e
standard. It provides basic Quality of Service (QoS) features to
IEEE 802.11 networks.
          
The levels of priority in EDCA are called access categories (ACs).
The contention window (CW) can be set according to the traffic
expected for each access category, with a wider window needed for
categories with heavier traffic.
          
Applies to AP. 802.11n products only.
cfgWlanWmeTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.3.5.1
WME entry.
Indexes
cfgWlanWmeIndex
Column Syntax OID
cfgWlanWmeIndex
Entry index of table.
Integer32
Constraints:
range: 0-31
 .1.3.6.1.4.1.16177.1.400.1.1.3.5.1.1
cfgWlanWmeId
ID of the WME parameter table. The virtual wireless interface
references to this ID.

Applies to AP. 802.11n products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.5.1.2
cfgWlanWmeAc
Access category (background, besteffort, video, voice).

Applies to AP. 802.11n products only.
Enumerationr/w
Enumerated Values:
0none
1background
2besteffort
3video
4voice
 .1.3.6.1.4.1.16177.1.400.1.1.3.5.1.3
cfgWlanWmeCwMin
Contention window minimum in exponential form.

Is used on STAs connected to this AP: `Real value = (2^n)-1`

Applies to AP. 802.11n products only.
Integer32r/w
Constraints:
range: 0-12
 .1.3.6.1.4.1.16177.1.400.1.1.3.5.1.4
cfgWlanWmeCwMax
Contention window maximum in exponential form.

Is used on STAs connected to this AP: `Real value = (2^n)-1`

Applies to AP. 802.11n products only.
Integer32r/w
Constraints:
range: 0-12
 .1.3.6.1.4.1.16177.1.400.1.1.3.5.1.5
cfgWlanWmeAifs
Arbitration inter-frame space.

Is used on STAs connected to this AP.

Applies to AP. 802.11n products only.
Integer32r/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.3.5.1.6
cfgWlanWmeTxOpMax
A Transmit Opportunity (TXOP) is a bound time interval during which
a station can send as many frames as possible (as long as the
duration of the transmissions does not exceed the maximum duration
of the TXOP). A value …
Integer32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.16177.1.400.1.1.3.5.1.7
cfgWlanWmeApCwMin
Contention window minimum.

Allowed values: 1, 3, 7, 15, 31, 63, 127, 255, 511, 1023.

Is used on the AP itself.

Applies to AP. 802.11n products only.
Integer32r/w
Constraints:
range: 1-1023
 .1.3.6.1.4.1.16177.1.400.1.1.3.5.1.8
cfgWlanWmeApCwMax
Contention window maximum.

Allowed values: 1, 3, 7, 15, 31, 63, 127, 255, 511, 1023

cwMax has to be greater or equal cwMin. Is used on the AP itself.

Applies to AP. 802.11n p…
Integer32r/w
Constraints:
range: 1-1023
 .1.3.6.1.4.1.16177.1.400.1.1.3.5.1.9
cfgWlanWmeApAifs
Arbitration inter-frame space.

Is used on the AP itself.

Applies to AP.
Integer32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.16177.1.400.1.1.3.5.1.10
cfgWlanWmeApBurst
Maximum length for bursting (equivalent to TxOpLimit).

This value is in units of 32us.
Is used on the AP itself.

Applies to AP. 802.11n products only.
Integer32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.16177.1.400.1.1.3.5.1.11

cfgWlanDbgTable

table
.1.3.6.1.4.1.16177.1.400.1.1.3.6 · 1 row entry · 14 columns
Open in standard view 
Wireless Handoff Debug Parameters.
cfgWlanDbgTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.3.6.1
Wireless Handoff Debug Parameters Entry.
Indexes
cfgWlanDbgIndex
Column Syntax OID
cfgWlanDbgIndex
Entry index of table.
Integer32
Constraints:
range: 0-63
 .1.3.6.1.4.1.16177.1.400.1.1.3.6.1.1
cfgWlanDbgIfaceName
Name of the virtual wireless interface.

Applies to STA. 802.11n products only.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.3.6.1.2
cfgWlanDbgHandoff
Persistent default value to enable/disable the handoff messages in
syslog. These log messages are subject to change. DO NOT PARSE!

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.6.1.3
cfgWlanDbgScan
Persistent default value to enable/disable the scan messages in
syslog. These log messages are subject to change. DO NOT PARSE!

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.6.1.4
cfgWlanDbgMlme
Persistent default value to enable/disable the MLME messages in
syslog. These log messages are subject to change. DO NOT PARSE!

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.6.1.5
cfgWlanDbgEvents
Persistent default value to enable/disable the events messages in
syslog. These log messages are subject to change. DO NOT PARSE!

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.6.1.6
cfgWlanDbgBeaconrssi
Persistent default value to enable/disable the beacon RSSI messages
in syslog. These log messages are subject to change. DO NOT PARSE!

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.6.1.7
cfgWlanDbgAckrssi
Persistent default value to enable/disable the ACK RSSI messages in
syslog. These log messages are subject to change. DO NOT PARSE!

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.6.1.8
cfgWlanDbgBeaconfiltered
Persistent default value to enable/disable the beacon filtered RSSI
messages in syslog. These log messages are subject to change. DO
NOT PARSE!

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.6.1.9
cfgWlanDbgRatelimit
Persistent default value to enable/disable the rate limiter
messages in syslog. These log messages are subject to change. DO
NOT PARSE!

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.6.1.10
cfgWlanDbgLinkmonitor
Periodically sends a trap containing link information of all
connected devices on this interface.

Applies to both AP and STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.6.1.11
cfgWlanDbgBeacontsf
Persistent default value to enable/disable the beacon RSSI messages
in syslog. These log messages are subject to change. DO NOT PARSE!
TS files is the TSF of the station.

Applies to STA. 802.11n products …
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.6.1.12
cfgWlanDbgRange
Persistent setting for distance measurement messages in syslog.

**Note:** Distance value is not in meters.

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.6.1.13
cfgWlanDbgReports
Persistent setting for periodical WLAN debug data reporting.

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.6.1.14

cfgWlanAclWhiteTable

table
.1.3.6.1.4.1.16177.1.400.1.1.3.7 · 1 row entry · 5 columns
Open in standard view 
Wireless MAC Access Control Whitelist
cfgWlanAclWhiteTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.3.7.1
Wireless MAC Access Control Whitelist Entry.
Indexes
cfgWlanAclWhiteIndex
Column Syntax OID
cfgWlanAclWhiteIndex
Entry index of table.
Integer32
Constraints:
range: 0-63
 .1.3.6.1.4.1.16177.1.400.1.1.3.7.1.1
cfgWlanAclWhiteEnabled
Enable this entry in the ACL.

Applies to AP.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.7.1.2
cfgWlanAclWhiteInterface
Name of the virtual wireless interface on which this entry is
active.

Applies to AP.
OctetStringr/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.3.7.1.3
cfgWlanAclWhiteAddr
MAC address in the ACL.

**Format:** `00:14:5a:02:10:42`

Applies to AP.
OctetStringr/w
Constraints:
range: 17-17
 .1.3.6.1.4.1.16177.1.400.1.1.3.7.1.4
cfgWlanAclWhiteMask
Mask of the MAC address to specify ranges of MAC addresses. To be
used like CIDR notation of IP addresses.

Applies to AP.
Integer32r/w
Constraints:
range: 0-48
 .1.3.6.1.4.1.16177.1.400.1.1.3.7.1.5

cfgWlanAclBlackTable

table
.1.3.6.1.4.1.16177.1.400.1.1.3.8 · 1 row entry · 5 columns
Open in standard view 
Wireless MAC Access Control Blacklist.
cfgWlanAclBlackTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.3.8.1
Wireless MAC Access Control Blacklist Entry.
Indexes
cfgWlanAclBlackIndex
Column Syntax OID
cfgWlanAclBlackIndex
Entry index of table.
Integer32
Constraints:
range: 0-63
 .1.3.6.1.4.1.16177.1.400.1.1.3.8.1.1
cfgWlanAclBlackEnabled
Enable this entry in the ACL.

Applies to AP.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.8.1.2
cfgWlanAclBlackInterface
Name of the virtual wireless interface on which this entry is
active.

Applies to AP.
OctetStringr/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.3.8.1.3
cfgWlanAclBlackAddr
MAC address in the ACL.

**Format:** `00:14:5a:02:10:42`

Applies to AP.
OctetStringr/w
Constraints:
range: 17-17
 .1.3.6.1.4.1.16177.1.400.1.1.3.8.1.4
cfgWlanAclBlackMask
Mask of the MAC address to enable the use of ranges of MAC
addresses. To be used like CIDR notation of IP addresses.

Applies to AP.
Integer32r/w
Constraints:
range: 0-48
 .1.3.6.1.4.1.16177.1.400.1.1.3.8.1.5

cfgWlan802dot1xTable

table
.1.3.6.1.4.1.16177.1.400.1.1.3.10 · 1 row entry · 12 columns
Open in standard view 
Wireless 802dot1x.
cfgWlan802dot1xTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.3.10.1
Wireless 802dot1x entry.
Indexes
cfgWlan802dot1xIndex
Column Syntax OID
cfgWlan802dot1xIndex
Entry index of table
Integer32
Constraints:
range: 0-63
 .1.3.6.1.4.1.16177.1.400.1.1.3.10.1.1
cfgWlan802dot1xName
Name of the virtual wireless interface.

Applies to AP and STA.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.3.10.1.2
cfgWlan802dot1xOwnIpAddr
The own IP address of the authenticator.
This field is used as NAS-IP-Address RADIUS attribute.
Set this to the IP address with which the authenticator will
communicate with the RADIUS server.

Applies to …
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.16177.1.400.1.1.3.10.1.3
cfgWlan802dot1xAuthServerParameter
Reference ID to the radius auth server table. Uses all parameters
in the cfgWlan802dot1xAuthServerTable which have as
cfgWlan802dot1xAuthSrvId the value set here.

Applies to AP.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.10.1.4
cfgWlan802dot1xAcctServerParameter
Reference ID to the radius acct server table. Uses all parameters
in the cfgWlan802dot1xAcctServerTable which have as
cfgWlan802dot1xAcctSrvId the value set here.

Applies to AP.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.10.1.5
cfgWlan802dot1xRetryPrimaryInterval
Retry interval for trying to return to the primary RADIUS server
(in seconds). RADIUS client code will automatically try to use the
next server when the current server is not replying to requests.
If this interval is se…
Integer32r/w
Constraints:
range: 0-86400
 .1.3.6.1.4.1.16177.1.400.1.1.3.10.1.6
cfgWlan802dot1xInterimAccountingInterval
Interim accounting update interval in seconds.

If this is set (larger than 0) and acct_server is configured,
hostapd will send interim accounting updates every N seconds. Set
to 0 to disable.
…
Integer32r/w
Constraints:
range: 0-86400
 .1.3.6.1.4.1.16177.1.400.1.1.3.10.1.7
cfgWlan802dot1xNasId
Optional NAS identifier string for RADIUS messages. When used,
this should be unique to the NAS within the scope of the RADIUS
server. For example, a fully qualified domain name can be used
here. When using IEEE 802.11r…
OctetStringr/w
Constraints:
range: 1-48
 .1.3.6.1.4.1.16177.1.400.1.1.3.10.1.8
cfgWlan802dot1xEapType
Specify the EAP type.

Applies to STA.
Enumerationr/w
Enumerated Values:
0tls
1peap
2ttls
 .1.3.6.1.4.1.16177.1.400.1.1.3.10.1.9
cfgWlan802dot1xIdentity
The identity string for EAP.

Applies to STA.
OctetStringr/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.3.10.1.10
cfgWlan802dot1xClientKeyPassword
The password to unlock the private key.

This is only required if the key is encrypted.

Applies to STA.
SNMPv2-TCDisplayStringr/w
Textual Convention: SNMPv2-TCDisplayString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.16177.1.400.1.1.3.10.1.17
cfgWlan802dot1xTlsControlParams
Bitfield to control TLS behaviour.

* **0x1** ignore certificate validity time
* **0x2** ignore ca certificate

Applies to STA.
Integer32r/w
Constraints:
range: 0-3
 .1.3.6.1.4.1.16177.1.400.1.1.3.10.1.18

cfgWlan802dot1xAuthServerTable

table
.1.3.6.1.4.1.16177.1.400.1.1.3.11 · 1 row entry · 6 columns
Open in standard view 
Wireless 802dot1x AuthServer.
cfgWlan802dot1xAuthServerTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.3.11.1
Wireless 802dot1x AuthServer entry.
Indexes
cfgWlan802dot1xAuthSrvIndex
Column Syntax OID
cfgWlan802dot1xAuthSrvIndex
Entry index of table.
Integer32
Constraints:
range: 0-255
 .1.3.6.1.4.1.16177.1.400.1.1.3.11.1.1
cfgWlan802dot1xAuthSrvEnabled
Enable this entry in the auth server list.

Applies to AP.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.11.1.2
cfgWlan802dot1xAuthSrvId
ID of the authorisation server table. The configuration item
cfgWlan802dot1xAuthServerParameter references to this ID.

Applies to AP.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.11.1.3
cfgWlan802dot1xAuthSrvIpAddr
IP of the RADIUS server against which will be authenticated.

Applies to AP.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.16177.1.400.1.1.3.11.1.4
cfgWlan802dot1xAuthSrvPort
Port of the RADIUS server against which will be authenticated.

Applies to AP.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.11.1.5
cfgWlan802dot1xAuthSrvSharedSecret
Password to connect to the specified RADIUS server.

Applies to AP.
OctetStringr/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.3.11.1.6

cfgWlan802dot1xAcctServerTable

table
.1.3.6.1.4.1.16177.1.400.1.1.3.12 · 1 row entry · 6 columns
Open in standard view 
Wireless 802dot1x AcctServer.
cfgWlan802dot1xAcctServerTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.3.12.1
Wireless 802dot1x AcctServer entry.
Indexes
cfgWlan802dot1xAcctSrvIndex
Column Syntax OID
cfgWlan802dot1xAcctSrvIndex
Entry index of table.
Integer32
Constraints:
range: 0-255
 .1.3.6.1.4.1.16177.1.400.1.1.3.12.1.1
cfgWlan802dot1xAcctSrvEnabled
Enable this entry in the acct server list.

Applies to AP.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.12.1.2
cfgWlan802dot1xAcctSrvId
ID of the accounting server table. The configuration item
cfgWlan802dot1xAcctServerParameter refers to this ID.

Applies to AP.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.12.1.3
cfgWlan802dot1xAcctSrvIpAddr
IP of the RADIUS accounting server.
Set to 0.0.0.0 to disable.

Applies to AP.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.16177.1.400.1.1.3.12.1.4
cfgWlan802dot1xAcctSrvPort
Port of the RADIUS accounting server.

Applies to AP.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.12.1.5
cfgWlan802dot1xAcctSrvSharedSecret
Password to connect to the specified RADIUS accounting server.

Applies to AP.
OctetStringr/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.3.12.1.6

cfgWlan802dot11rTable

table
.1.3.6.1.4.1.16177.1.400.1.1.3.13 · 1 row entry · 13 columns
Open in standard view 
Wireless 802dot11r.
cfgWlan802dot11rTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.3.13.1
Wireless 802dot11r Entry.
Indexes
cfgWlan802dot11rIndex
Column Syntax OID
cfgWlan802dot11rIndex
Entry index of Table.
Integer32
Constraints:
range: 0-63
 .1.3.6.1.4.1.16177.1.400.1.1.3.13.1.1
cfgWlan802dot11rName
Name of the virtual wireless interface.

Applies to AP and STA. 802.11n products only.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.3.13.1.2
cfgWlan802dot11rEnabled
Enable usage of 802.11r on this device.

Applies to AP and STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.13.1.3
cfgWlan802dot11rMobilityDomain
Mobility Domain identifier (dot11FTMobilityDomainID, MDID)
MDID is used to indicate a group of APs (within an ESS, i.e.,
sharing the same SSID) between which a STA can use Fast BSS
Transition. 2-octet identifier as a he…
OctetStringr/w
Constraints:
range: 4-4
 .1.3.6.1.4.1.16177.1.400.1.1.3.13.1.4
cfgWlan802dot11rPmkR0KeyHolderIdentifier
PMK-R0 Key Holder identifier (dot11FTR0KeyHolderID).

Configure this in the field cfgWlan802dot1xNasId.

Applies to AP. 802.11n products only.
OctetString
Constraints:
range: 1-48
 .1.3.6.1.4.1.16177.1.400.1.1.3.13.1.5
cfgWlan802dot11rPmkR0Lifetime
PMK-RO lifetime in seconds (dot11FTR0KeyLifetime).

When Session-Timeout attribute is provided by RADIUS server, then
min(Session-Timeout, cfgWlan802dot11rPmkR0Lifetime) is used.

**Ranges**
…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.13.1.6
cfgWlan802dot11rPmkR1KeyHolderIdentifier
PMK-R1 Key Holder identifier (dot11FTR0KeyHolderID).

6-octet identifier as a hex string. This may be the same as the
local MAC address. Default magic number 000102030405 means use own
mac address (bssid).…
OctetStringr/w
Constraints:
range: 12-12
 .1.3.6.1.4.1.16177.1.400.1.1.3.13.1.7
cfgWlan802dot11rPmkR1Push
Whether PMK-R1 push is enabled at R0KH.

* **0** do not push PMK-R1 to all configured R1KHs (default).
* **1** push PMK-R1 to all configured R1KHs whenever a new PMK-R0 is derived.

Applies t…
Enumerationr/w
Enumerated Values:
0donotpush
1push
 .1.3.6.1.4.1.16177.1.400.1.1.3.13.1.9
cfgWlan802dot11rR0KHParameter
Reference ID to the R0KH parameter table. Uses all parameters in
the cfgWlan802dot11rR0KHTable which have as
cfgWlan802dot11rR0KHTblId the value set here.

Applies to AP. 802.11n products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.13.1.10
cfgWlan802dot11rR1KHParameter
Reference ID to the R1KH parameter table. Uses all parameters in
the cfgWlan802dot11rR1KHTable which have as
cfgWlan802dot11rR1KHTblId the value set here.

Applies to AP. 802.11n products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.13.1.11
cfgWlan802dot11rExpirationEnabled
Enable/disable PMK-R0/-R1 expiration forcing.

If set to **enabled(1)**, AP forces PMK-R0s and PMK-R1s
expiration once a day (see `cfgWlan802dot11rExpirationTime`).

Applies to AP. 802.11n pr…
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.13.1.12
cfgWlan802dot11rExpirationTime
Daily PMK-R0/-R1 expiration time.

Define time (hour:minute) at which PMK-R0s and PMK-R1s
expiration is daily forced (if `cfgWlan802dot11rExpirationEnabled`
is **enabled(1)**).

The time is r…
OctetStringr/w
Constraints:
range: 5-5
 .1.3.6.1.4.1.16177.1.400.1.1.3.13.1.13
cfgWlan802dot11rVlan
The 802.1q VLAN tag of 802.11r backbone traffic.

Defines the VLAN tag with which all 802.11r managment frames
(ethertype 0x88b7) are transmitted on the backbone.

Setting a value of 0 disabl…
Integer32r/w
Constraints:
range: 0-4094
 .1.3.6.1.4.1.16177.1.400.1.1.3.13.1.14

cfgWlan802dot11rR0KHTable

table
.1.3.6.1.4.1.16177.1.400.1.1.3.14 · 1 row entry · 6 columns
Open in standard view 
Wireless 802dot11r R0KH.
          
List of R0KHs in the same Mobility Domain. This list is used to map
R0KH-ID (NAS Identifier) to a destination MAC address when
requesting PMK-R1 key from the R0KH that the STA used during the
Initial Mobility Domain Association.
          
**Format:** `<MAC address> <NAS Identifier> <128-bit key as hex string>`
          
**Example**
          
~~~
r0kh=02:01:02:03:04:05 r0kh-1.example.com 000102030405060708090a0b0c0d0e0f
r0kh=02:01:02:03:04:06 r0kh-2.example.com 00112233445566778899aabbccddeeff
~~~
          
Applies to AP. 802.11n products only.
cfgWlan802dot11rR0KHTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.3.14.1
Wireless 802dot11r R0KH Entry.
Indexes
cfgWlan802dot11rR0KHIndex
Column Syntax OID
cfgWlan802dot11rR0KHIndex
Entry index of Table.
Integer32
Constraints:
range: 0-511
 .1.3.6.1.4.1.16177.1.400.1.1.3.14.1.1
cfgWlan802dot11rR0KHId
ID of the R0KH table.

The configuration item cfgWlan802dot11rR0KHParameter references to
this ID.

Applies to AP. 802.11n products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.14.1.2
cfgWlan802dot11rR0KHEnabled
Enable this entry in the R0KH list.

Applies to AP. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.14.1.3
cfgWlan802dot11rR0KHDestinationMac
MAC addresses of all possible R0KHs from which PMK-R1 can be requested.

**Format:** `02:01:02:03:04:05`

Applies to AP. 802.11n products only.
OctetStringr/w
Constraints:
range: 17-17
 .1.3.6.1.4.1.16177.1.400.1.1.3.14.1.4
cfgWlan802dot11rR0KHHID
NAS Identifier of all R0KHs to map to the MAC address.

See the field: cfgWlan802dot11rPmkR0KeyHolderIdentifier.

Applies to AP. 802.11n products only.
OctetStringr/w
Constraints:
range: 1-48
 .1.3.6.1.4.1.16177.1.400.1.1.3.14.1.5
cfgWlan802dot11rR0KHKey
Static Key of the R0KH.

Connecting R1KHs need to have this key configured.

**Format:** `000102030405060708090a0b0c0d0e0f`

Applies to AP. 802.11n products only.
OctetStringr/w
Constraints:
range: 32-32
 .1.3.6.1.4.1.16177.1.400.1.1.3.14.1.6

cfgWlan802dot11rR1KHTable

table
.1.3.6.1.4.1.16177.1.400.1.1.3.15 · 1 row entry · 6 columns
Open in standard view 
Wireless 802dot11r R1KH.
          
List of R1KHs in the same Mobility Domain
This list is used to map R1KH-ID to a destination MAC address when
sending PMK-R1 key from the R0KH. This is also the list of
authorized R1KHs in the MD that can request PMK-R1 keys.
          
**Format:** `<MAC address> <R1KH-ID> <128-bit key as hex string>`
          
**Example**
          
~~~
r1kh=02:01:02:03:04:05 02:11:22:33:44:55 000102030405060708090a0b0c0d0e0f
r1kh=02:01:02:03:04:06 02:11:22:33:44:66 00112233445566778899aabbccddeeff
~~~
          
Applies to AP. 802.11n products only.
cfgWlan802dot11rR1KHTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.3.15.1
Wireless 802dot11r R1KH Entry.
Indexes
cfgWlan802dot11rR1KHIndex
Column Syntax OID
cfgWlan802dot11rR1KHIndex
Entry index of Table.
Integer32
Constraints:
range: 0-511
 .1.3.6.1.4.1.16177.1.400.1.1.3.15.1.1
cfgWlan802dot11rR1KHId
ID of the R1KH table.

The configuration item cfgWlan802dot11rR1KHParameter references to
this ID.

Applies to AP.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.15.1.2
cfgWlan802dot11rR1KHEnabled
Enable this entry in the R1KH list.

Applies to AP. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.15.1.3
cfgWlan802dot11rR1KHDestinationMac
MAC addresses of all R1KHs which can reqest PMK-R1 from the local
R0KH.

**Format:** `02:01:02:03:04:05`

Applies to AP.
OctetStringr/w
Constraints:
range: 17-17
 .1.3.6.1.4.1.16177.1.400.1.1.3.15.1.4
cfgWlan802dot11rR1KHHID
PMK-R1 Key Holder identifier (dot11FTR1KeyHolderID)

6-octet identifier as a hex string to map to the MAC. This may be
the same as the destination MAC. See the field
cfgWlan802dot11rPmkR1KeyHolderIdentifie…
OctetStringr/w
Constraints:
range: 17-17
 .1.3.6.1.4.1.16177.1.400.1.1.3.15.1.5
cfgWlan802dot11rR1KHKey
Static Key of the R0KH.

These keys are used wenn sending updates to R1KHs from the local
R0KH. The respective key has to match the respective entry on the
target in the field cfgWlan802dot11rR0KHKey.
…
OctetStringr/w
Constraints:
range: 32-32
 .1.3.6.1.4.1.16177.1.400.1.1.3.15.1.6

cfgWlanNeighbourTable

table
.1.3.6.1.4.1.16177.1.400.1.1.3.16 · 1 row entry · 5 columns
Open in standard view 
Hostapd Neighbour Table.
cfgWlanNeighbourTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.3.16.1
Hostapd Neighbour Table Entry.
Indexes
cfgWlanNeighbourIndex
Column Syntax OID
cfgWlanNeighbourIndex
Entry index of Table.
Integer32
Constraints:
range: 0-511
 .1.3.6.1.4.1.16177.1.400.1.1.3.16.1.1
cfgWlanNeighbourId
ID of the neighbour table. The configuration item
`cfgWlanIfaceNeighbourParameter` references to this ID.

Applies to AP. 802.11n products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.3.16.1.2
cfgWlanNeighbourEnabled
Enable this entry in the list.

Applies to AP. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.3.16.1.3
cfgWlanNeighbourBSSID
BSSID (MAC address) of the neighbour.

**Format:** `00:14:5a:02:10:42`

Applies to AP.
OctetStringr/w
Constraints:
range: 17-17
 .1.3.6.1.4.1.16177.1.400.1.1.3.16.1.4
cfgWlanNeighbourFrequency
Frequency in MHz of the neighbour.

Applies to AP. 802.11n products only.
Integer32r/w
Constraints:
range: 1-6000
 .1.3.6.1.4.1.16177.1.400.1.1.3.16.1.5

cfgRouteTable

table
.1.3.6.1.4.1.16177.1.400.1.1.4.2 · 1 row entry · 6 columns
Open in standard view 
Static routes
cfgRouteTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.4.2.1
Static route.
Indexes
cfgRouteTableIndex
Column Syntax OID
cfgRouteTableIndex
Entry index of table.
Integer32
Constraints:
range: 0-265
 .1.3.6.1.4.1.16177.1.400.1.1.4.2.1.1
cfgRouteTableEnabled
Enable/Disable this route entry.

Applies to AP and STA.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.4.2.1.2
cfgRouteTableDestinationNetwork
Destination network in CIDR notation.

Applies to AP and STA.
SNMPv2-TCDisplayStringr/w
Textual Convention: SNMPv2-TCDisplayString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.16177.1.400.1.1.4.2.1.3
cfgRouteTableGateway
Gateway to destination network.

Applies to AP and STA.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.16177.1.400.1.1.4.2.1.5
cfgRouteTableSource
Source for traffic to destination network.

Optional. Use only if you have multiple possible sources.

Applies to AP and STA.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.16177.1.400.1.1.4.2.1.6
cfgRouteTableCarpId
The CARP instance which brings this route up.

Has to be set to -1 when this is a normal route and should not be
handled by a CARP instance.
All routes which have a value 0..15 are brought up by the respec…
Integer32r/w
Constraints:
range: -1-15
 .1.3.6.1.4.1.16177.1.400.1.1.4.2.1.8

cfgMRouteTable

table
.1.3.6.1.4.1.16177.1.400.1.1.4.3 · 1 row entry · 6 columns
Open in standard view 
Static multicast routes.
cfgMRouteTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.4.3.1
Static multicast routes.
Indexes
cfgMRouteTableIndex
Column Syntax OID
cfgMRouteTableIndex
Entry index of table.
Integer32
Constraints:
range: 0-255
 .1.3.6.1.4.1.16177.1.400.1.1.4.3.1.1
cfgMRouteTableEnabled
Enable/Disable this multicast route entry.

Applies to AP and STA.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.4.3.1.2
cfgMRouteTableInput
Input interface.

Applies to AP and STA.
OctetStringr/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.4.3.1.3
cfgMRouteTableSource
Unicast source address to listen to.

If it is set to 0.0.0.0 all multicast traffic will be forwarded.

Applies to AP and STA.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.16177.1.400.1.1.4.3.1.4
cfgMRouteTableGroup
Multicast group to forward.

Applies to AP and STA.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.16177.1.400.1.1.4.3.1.5
cfgMRouteTableOutput
Output interface(s).

Can be a list of interface names separated by spaces.

Applies to AP and STA.
OctetStringr/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.4.3.1.6

cfgQosDscpToTidMapTable

table
.1.3.6.1.4.1.16177.1.400.1.1.6.2 · 1 row entry · 2 columns
Open in standard view 
Mapping table from DSCP class selector (IP TOS) to
wireless priority (TID).
cfgQosDscpToTidMapTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.6.2.1
QoS DSCP to TID Mapping Table Entry.
Indexes
cfgQosDscpToTidMapTableIndex
Column Syntax OID
cfgQosDscpToTidMapTableIndex
QoS DSCP to TID Mapping Table Index.
Integer32
Constraints:
range: 0-7
 .1.3.6.1.4.1.16177.1.400.1.1.6.2.1.1
cfgQosDscpToTidMapValue
Layer 2 priorities for IP precedence values 0-7.

Applies to AP and STA. 802.11n products only.
Integer32r/w
Constraints:
range: 0-7
 .1.3.6.1.4.1.16177.1.400.1.1.6.2.1.2

cfgQosVlanToTidMapTable

table
.1.3.6.1.4.1.16177.1.400.1.1.6.3 · 1 row entry · 2 columns
Open in standard view 
Mapping table from layer 2 priorities (802.1p)
to wireless priority (TID).
cfgQosVlanToTidMapTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.6.3.1
QoS Vlan to TID Priority Table Entry.
Indexes
cfgQosVlanToTidMapTableIndex
Column Syntax OID
cfgQosVlanToTidMapTableIndex
QoS Vlan to TID Priority Table Entry Index.
Integer32
Constraints:
range: 0-7
 .1.3.6.1.4.1.16177.1.400.1.1.6.3.1.1
cfgQosVlanToTidMapValue
Layer 2 priorities for VLAN priorities 0-7.

Applies to AP and STA. 802.11n products only.
Integer32r/w
Constraints:
range: 0-7
 .1.3.6.1.4.1.16177.1.400.1.1.6.3.1.2

cfgQosIpToTidMapTable

table
.1.3.6.1.4.1.16177.1.400.1.1.6.4 · 1 row entry · 8 columns
Open in standard view 
Mapping table from IP header (Source, Destination, Protocol, Port),
to wireless priority (TID).
cfgQosIpToTidMapTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.6.4.1
IP to TID Priority Table Entry.
Indexes
cfgQosIpToTidMapTableIndex
Column Syntax OID
cfgQosIpToTidMapTableIndex
IP to TID Priority Table Index.
Integer32
Constraints:
range: 0-127
 .1.3.6.1.4.1.16177.1.400.1.1.6.4.1.1
cfgQosIpToTidMapSrcNet
Source network for ip prioritization rule, in CIDR format.

Applies to AP and STA. 802.11n products only.
OctetStringr/w .1.3.6.1.4.1.16177.1.400.1.1.6.4.1.2
cfgQosIpToTidMapDestNet
Destination network for ip prioritization rule, in CIDR format.

Applies to AP and STA. 802.11n products only.
OctetStringr/w .1.3.6.1.4.1.16177.1.400.1.1.6.4.1.3
cfgQosIpToTidMapProto
Protocol for ip prioritization rule, allowed protocols are:
**any(0)**, **udp(1)** or **tcp(2)**.

Applies to AP and STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0any
1udp
2tcp
 .1.3.6.1.4.1.16177.1.400.1.1.6.4.1.4
cfgQosIpToTidMapSrcPort
Source port for ip prioritization rule, use port -1 to match any
port.

This setting can only be used if the protocol is set to udp or tcp.

Applies to AP and STA. 802.11n products only.
Integer32r/w
Constraints:
range: -1-65536
 .1.3.6.1.4.1.16177.1.400.1.1.6.4.1.5
cfgQosIpToTidMapDestPort
Destination port for ip prioritization rule, use port -1 to match
any port.

This setting can only be used if the protocol is set to udp or tcp.

Applies to AP and STA. 802.11n products only.
Integer32r/w
Constraints:
range: -1-65536
 .1.3.6.1.4.1.16177.1.400.1.1.6.4.1.6
cfgQosIpToTidMapPrecedence
Precedence to set for ip prioritization rule.

Applies to AP and STA. 802.11n products only.
Integer32r/w
Constraints:
range: 0-7
 .1.3.6.1.4.1.16177.1.400.1.1.6.4.1.7
cfgQosIpToTidMapEnabled
Enable/disable ip prioritisation rules.

Applies to AP and STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.6.4.1.8

cfgLogRemoteTable

table
.1.3.6.1.4.1.16177.1.400.1.1.11.2.1 · 1 row entry · 6 columns
Open in standard view 
List of syslog destinations.
cfgLogRemoteTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.11.2.1.1
List of syslog destinations.
Indexes
cfgLogRemoteIndex
Column Syntax OID
cfgLogRemoteIndex
Entry index of table
Integer32
Constraints:
range: 0-1
 .1.3.6.1.4.1.16177.1.400.1.1.11.2.1.1.1
cfgLogRemoteEnabled
Log messages to file.

Applies to AP and STA.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.11.2.1.1.2
cfgLogRemoteLevel
Log only messages with equal or higher priority than prio N (0-7).

Applies to AP and STA.
Enumeration
Enumerated Values:
0emergency
1alert
2critical
3error
4warning
5notice
6info
7debug
 .1.3.6.1.4.1.16177.1.400.1.1.11.2.1.1.3
cfgLogRemoteProtocol
Protocol to send log messages. The udp(0) protocol complies with
the standard syslog protocol.

Applies to AP and STA.
Enumerationr/w
Enumerated Values:
0udp
1tcp
 .1.3.6.1.4.1.16177.1.400.1.1.11.2.1.1.4
cfgLogRemoteIp
Remote IP address.

Applies to AP and STA.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.16177.1.400.1.1.11.2.1.1.5
cfgLogRemotePort
Remote port.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.11.2.1.1.6

cfgDhcpDnsmasqTable

table
.1.3.6.1.4.1.16177.1.400.1.1.13.2 · 1 row entry · 2 columns
Open in standard view 
DHCP Dnsmasq instances.
cfgDhcpDnsmasqTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.13.2.1
DHCP Dnsmasq instances.
Indexes
cfgDhcpDnsmasqIndex
Column Syntax OID
cfgDhcpDnsmasqIndex
Entry index of table.
Integer32
Constraints:
range: 0-9
 .1.3.6.1.4.1.16177.1.400.1.1.13.2.1.1
cfgDhcpDnsmasqScopeParameter
Parameter to set which scope ID to use for the DHCP server.

This is used in conjunction with the scope ID parameter
(see cfgDhcpScopeId).
Integer32r/w
Constraints:
range: 0-8
 .1.3.6.1.4.1.16177.1.400.1.1.13.2.1.2

cfgDhcpScopeTable

table
.1.3.6.1.4.1.16177.1.400.1.1.13.3 · 1 row entry · 9 columns
Open in standard view 
DHCP instance configs.
cfgDhcpScopeTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.13.3.1
DHCP instance configs.
Indexes
cfgDhcpScopeIndex
Column Syntax OID
cfgDhcpScopeIndex
Entry index of table.
Integer32
Constraints:
range: 0-7
 .1.3.6.1.4.1.16177.1.400.1.1.13.3.1.1
cfgDhcpScopeId
Several scopes can share the same ID.

This is used in conjunction with the DHCP parameter
(see cfgDhcpDnsmasqScopeParameter).

Applies to AP and STA.
Integer32r/w
Constraints:
range: 0-8
 .1.3.6.1.4.1.16177.1.400.1.1.13.3.1.2
cfgDhcpScopeInterface
Network interface (ETH, VLAN, WLAN) on which the DHCP server runs.

If the interface is part of a bridge, the server will run on that
bridge.

Applies to AP and STA.
OctetStringr/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.13.3.1.3
cfgDhcpScopeStart
Specifies the offset from the network address of the underlying
interface to calculate the minimum address that may be leased to
clients. It may be greater than 255 to span subnets.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.13.3.1.4
cfgDhcpScopeLimit
Specifies the maximum allowable address that may be leased to
clients, calculated as network address + 'start' + 'limit'.

Applies to AP and STA.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.13.3.1.5
cfgDhcpScopeLeasetime
Specifies the lease time of addresses handed out to clients,
e.g. 12h or 30m.

Applies to AP and STA.
OctetStringr/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.13.3.1.6
cfgDhcpScopeGateway
Specifies the gateway address handed out to clients.

A value of 0.0.0.0 means not used.

Applies to AP and STA.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.16177.1.400.1.1.13.3.1.7
cfgDhcpScopeDnsServer1
Specifies the primary DNS server address handed out to clients.

A value of 0.0.0.0 means not used.

Applies to AP and STA.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.16177.1.400.1.1.13.3.1.8
cfgDhcpScopeDnsServer2
Specifies the secondary DNS server address handed out to clients.

If the first DNS server is not used, this server will also be
ignored. A value of 0.0.0.0 means not used.

Applies to AP and…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.16177.1.400.1.1.13.3.1.9

cfgNlmMonitorTable

table
.1.3.6.1.4.1.16177.1.400.1.1.40.2 · 1 row entry · 10 columns
Open in standard view 
NLM Monitor Table.
cfgNlmMonitorTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.40.2.1
NLM Monitor Table Entry.
Indexes
cfgNlmMonIndex
Column Syntax OID
cfgNlmMonIndex
Entry index of Table.
Integer32
Constraints:
range: 0-255
 .1.3.6.1.4.1.16177.1.400.1.1.40.2.1.1
cfgNlmMonEnabled
Enable this entry in the monitor list.

Applies to AP and STA.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.40.2.1.2
cfgNlmMonInterval
Execution interval of this monitor in milliseconds.

In case of an event driven monitor (e.g. `cfgNlmMonType` set to
**wlan(2)**), this defines a timeout.

Applies to AP and STA.
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.40.2.1.3
cfgNlmMonCount
NLM monitor counter.

The number of times the measured criteria has to be down, until
the monitor is reported as down.

Applies to AP and STA.
Integer32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.16177.1.400.1.1.40.2.1.4
cfgNlmMonType
Objects which can be monitored.

* **phy(0)** monitor checks periodically the link status of the
ethernet interfaces defined by `cfgNlmMonInterfaces`. If at least
one interface in the list specified is…
Enumerationr/w
Enumerated Values:
0phy
1icmp
2wlan
 .1.3.6.1.4.1.16177.1.400.1.1.40.2.1.5
cfgNlmMonInterfaces
NLM monitor interface(s).

This parameter specifies the name of the interface(s)
which is/are to be monitored.

For the type **phy(0)** multiple interfaces are allowed.

For the…
OctetStringr/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.40.2.1.6
cfgNlmMonDestination
NLM monitor destination.

This parameter specifies the IPv4 address which is to be monitored.

It will only be used when `cfgNlmMonType` is set to **icmp(1)**.

Applies to AP an…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.16177.1.400.1.1.40.2.1.7
cfgNlmMonUpAction
NLM 'up' state monitor action.

The action is executed on a monitor-state transition to 'up'.

Set to 0 to disable (i.e. no action).

Supported actions:

**1xxx** …
Integer32r/w
Constraints:
range: 0-2255
 .1.3.6.1.4.1.16177.1.400.1.1.40.2.1.10
cfgNlmMonDownAction
NLM 'down' state monitor script.

The action is executed on a monitor-state transition to 'down'.

Set to 0 to disable (i.e. no action).

Supported actions:

**1xx…
Integer32r/w
Constraints:
range: 0-2255
 .1.3.6.1.4.1.16177.1.400.1.1.40.2.1.11
cfgNlmMonScanLoopInterval
Scan loop debounce interval in milliseconds.

If set to non-zero it will mark interface 'down' after
receiving scan loop trap 415 and mark it 'up' after
scan loop interval if no other 415 events have been
…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.16177.1.400.1.1.40.2.1.12

cfgCellSimTable

table
.1.3.6.1.4.1.16177.1.400.1.1.101.1 · 1 row entry · 7 columns
Open in standard view 
SIM parameter table
          
Applies to LTE products only.
cfgCellSimTableEntry entry .1.3.6.1.4.1.16177.1.400.1.1.101.1.1
SIM parameter table entry

Applies to LTE products only.
Indexes
cfgCellSimIndex
Column Syntax OID
cfgCellSimIndex
SIM parameter table entry index

Applies to LTE products only.
Integer32
Constraints:
range: 0-9
 .1.3.6.1.4.1.16177.1.400.1.1.101.1.1.1
cfgCellSimApn
APN (Access Point Name)

**Example**

* gprs.swisscom.ch

Applies to LTE products only.
OctetStringr/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.101.1.1.2
cfgCellSimUsername
Username

Applies to LTE products only.
OctetStringr/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.101.1.1.3
cfgCellSimPassword
Password

Applies to LTE products only.
OctetStringr/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.1.101.1.1.4
cfgCellSimPinEnabled
PIN authentication enabled

Set to enabled if PIN authentication is required for this SIM.

Applies to LTE products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.1.101.1.1.5
cfgCellSimPin
SIM PIN

Applies to LTE products only.
OctetStringr/w
Constraints:
range: 4-4
 .1.3.6.1.4.1.16177.1.400.1.1.101.1.1.6
cfgCellSimAuthType
Authentication type

Applies to LTE products only.
Enumerationr/w
Enumerated Values:
0none
1pap
2chap
3both
 .1.3.6.1.4.1.16177.1.400.1.1.101.1.1.7

rpcDrvTable

table
.1.3.6.1.4.1.16177.1.400.1.3.6.1 · 1 row entry · 3 columns
Open in standard view 
RPC driver module
rpcDrvTableEntry entry .1.3.6.1.4.1.16177.1.400.1.3.6.1.1
RPC driver module
Indexes
rpcDrvIndex
Column Syntax OID
rpcDrvIndex
Entry index of table
Integer32
Constraints:
range: 0-1
 .1.3.6.1.4.1.16177.1.400.1.3.6.1.1.1
rpcDrvName
Name of the radio device

Applies to AP.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.3.6.1.1.2
rpcDrvDfsSimulateRadar
Simulate a radar detection on the current channel.

Applies to AP.
Enumerationr/w
Enumerated Values:
0nop
1fire
 .1.3.6.1.4.1.16177.1.400.1.3.6.1.1.5

setWlanDeviceTable

table
.1.3.6.1.4.1.16177.1.400.1.4.3.1 · 1 row entry · 5 columns
Open in standard view 
Wireless hardware modules.
setWlanDeviceTableEntry entry .1.3.6.1.4.1.16177.1.400.1.4.3.1.1
Wireless hardware module.
Indexes
setWlanDevIndex
Column Syntax OID
setWlanDevIndex
Entry index of table
Integer32
Constraints:
range: 0-1
 .1.3.6.1.4.1.16177.1.400.1.4.3.1.1.1
setWlanDevName
Name of the wireless device.

Applies to AP and STA.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.4.3.1.1.2
setWlanDevRfOutput
Enable/disable RF output.

Applies to AP and STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.4.3.1.1.3
setWlanDevFrequency
Wireless frequency in MHz.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.4.3.1.1.6
setWlanDevPower
Wireless output power as effective isotropic radiated power (EIRP) in dBm
including antenna gain.


Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.4.3.1.1.8

setWlanDbgTable

table
.1.3.6.1.4.1.16177.1.400.1.4.3.6 · 1 row entry · 13 columns
Open in standard view 
Wireless handoff debug parameters.
setWlanDbgTableEntry entry .1.3.6.1.4.1.16177.1.400.1.4.3.6.1
Wireless handoff debug parameters entry.
Indexes
setWlanDbgIndex
Column Syntax OID
setWlanDbgIndex
Entry index of table
Integer32
Constraints:
range: 0-63
 .1.3.6.1.4.1.16177.1.400.1.4.3.6.1.1
setWlanDbgIfaceName
Name of the virtual wireless interface.

Applies to AP and STA. 802.11n products only.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.4.3.6.1.2
setWlanDbgHandoff
Volatile setting to enable/disable the handoff messages in syslog.

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.4.3.6.1.3
setWlanDbgScan
Volatile setting to enable/disable the scan messages in syslog.

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.4.3.6.1.4
setWlanDbgMlme
Volatile setting to enable/disable the MLME messages in syslog.

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.4.3.6.1.5
setWlanDbgEvents
Volatile setting to enable/disable the Events messages in syslog.

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.4.3.6.1.6
setWlanDbgBeaconrssi
Volatile setting to enable/disable the Beacon RSSI messages in
syslog.

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.4.3.6.1.7
setWlanDbgAckrssi
Volatile setting to enable/disable the ACK RSSI messages in syslog.

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.4.3.6.1.8
setWlanDbgBeaconfiltered
Volatile setting to enable/disable the Beacon filtered RSSI
messages in syslog.

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.4.3.6.1.9
setWlanDbgRatelimit
Volatile value to enable/disable the rate limiter messages in syslog.
These log messages are subject to change. DO NOT PARSE!

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.4.3.6.1.10
setWlanDbgBeacontsf
Volatile setting to enable/disable the beacon RSSI messages in syslog.
These log messages are subject to change. DO NOT PARSE! TS is internal TSF.

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.4.3.6.1.12
setWlanDbgRange
Volatile setting for distance measurement messages in syslog.

**Note:** Distance value is not in meters.

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.4.3.6.1.13
setWlanDbgReports
Volatile setting for periodical WLAN debug data reporting.

Applies to STA. 802.11n products only.
Enumerationr/w
Enumerated Values:
0disabled
1enabled
 .1.3.6.1.4.1.16177.1.400.1.4.3.6.1.14

hwNetEthernetTable

table
.1.3.6.1.4.1.16177.1.400.1.5.2.1 · 1 row entry · 7 columns
Open in standard view 
Ethernet network interfaces
hwNetEthernetTableEntry entry .1.3.6.1.4.1.16177.1.400.1.5.2.1.1
Ethernet network interface
Indexes
hwNetEthIndex
Column Syntax OID
hwNetEthIndex
Entry index of table
Integer32
Constraints:
range: 0-2
 .1.3.6.1.4.1.16177.1.400.1.5.2.1.1.1
hwNetEthName
Name of the ethernet interface.

Applies to AP and STA.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.5.2.1.1.2
hwNetEthAssembled
Ethernet interface present or not.

Applies to AP and STA.
Enumeration
Enumerated Values:
0inexistent
1present
 .1.3.6.1.4.1.16177.1.400.1.5.2.1.1.3
hwNetEthMacAddress
Ethernet MAC address..

Applies to AP and STA.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.5.2.1.1.4
hwNetEthOperation
Ethernet interface plugged or unplugged.

Applies to AP and STA.
Enumeration
Enumerated Values:
0down
1up
 .1.3.6.1.4.1.16177.1.400.1.5.2.1.1.5
hwNetEthSpeed
Ethernet speed in Mbps.

Applies to AP and STA.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.5.2.1.1.6
hwNetEthHwIndex
The physical address of the Ethernet interface of the base board,
since not all products are assembled the same way this is to
describe how the wiring is done.

Applies to AP and STA.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.5.2.1.1.7

hwWlanDeviceTable

table
.1.3.6.1.4.1.16177.1.400.1.5.3.1 · 1 row entry · 12 columns
Open in standard view 
Hardware information of the wireless LAN devices.
hwWlanDeviceTableEntry entry .1.3.6.1.4.1.16177.1.400.1.5.3.1.1
Wireless LAN devices
Indexes
hwWlanDevIndex
Column Syntax OID
hwWlanDevIndex
Entry index of table
Integer32
Constraints:
range: 0-1
 .1.3.6.1.4.1.16177.1.400.1.5.3.1.1.1
hwWlanDevAssembled
Wireless device present or not.

Applies to AP and STA.
Enumeration
Enumerated Values:
0inexistent
1present
 .1.3.6.1.4.1.16177.1.400.1.5.3.1.1.2
hwWlanDevType
Type of the wireless device.

Applies to AP and STA.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.5.3.1.1.3
hwWlanDevSerial
Serial number / customer field.

Applies to AP and STA.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.5.3.1.1.4
hwWlanDevRevision
ERP revision of the RF board.

Applies to AP and STA.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.5.3.1.1.5
hwWlanDevVersion
Version of the RF board.

Applies to AP and STA.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.5.3.1.1.6
hwWlanDevPcbId
Hardware assembly ID.

Applies to AP and STA.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.5.3.1.1.7
hwWlanDevAssemblyId
Hardware assembly ID.

Applies to AP and STA.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.5.3.1.1.8
hwWlanDevMacAddress
MAC address.

Applies to AP and STA.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.5.3.1.1.9
hwWlanDevAntennaProfileId
Antenna profile ID.

Please check the user manual for antenna details.

Applies to AP and STA.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.5.3.1.1.10
hwWlanDevAntennaGain
Antenna gain in dBi.

Applies to AP and STA.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.5.3.1.1.11
hwWlanDevCableLoss
Cable loss in dB.

Applies to AP and STA.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.5.3.1.1.12

hwSensorTable

table
.1.3.6.1.4.1.16177.1.400.1.5.21.1 · 1 row entry · 4 columns
Open in standard view 
Hardware sensor information table.
hwSensorTableEntry entry .1.3.6.1.4.1.16177.1.400.1.5.21.1.1
Hardware sensor entry.
Indexes
hwSensorIndex
Column Syntax OID
hwSensorIndex
Entry index of table.
Integer32
Constraints:
range: 0-15
 .1.3.6.1.4.1.16177.1.400.1.5.21.1.1.1
hwSensorName
Name of the hardware sensor.

Applies to AP and STA.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.5.21.1.1.2
hwSensorUnit
Unit of the hardware sensor.

Applies to AP and STA.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.5.21.1.1.3
hwSensorValue
Value of the hardware sensor.

Applies to AP and STA.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.5.21.1.1.4

swSysMessageTable

table
.1.3.6.1.4.1.16177.1.400.1.6.3.100 · 1 row entry · 4 columns
Open in standard view 
System messages (e.g. errors, warnings).
swSysMessageTableEntry entry .1.3.6.1.4.1.16177.1.400.1.6.3.100.1
System message entry
Indexes
swSysMsgIndex
Column Syntax OID
swSysMsgIndex
Entry index of table.
Integer32
Constraints:
range: 0-63
 .1.3.6.1.4.1.16177.1.400.1.6.3.100.1.1
swSysMsgPriority
Message priority/level.

Applies to AP and STA.
Enumeration
Enumerated Values:
0emergency
1alert
2critical
3error
4warning
5notice
6info
7debug
 .1.3.6.1.4.1.16177.1.400.1.6.3.100.1.2
swSysMsgCode
Message code.

Applies to AP and STA.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.3.100.1.3
swSysMsgText
Message.

Applies to AP and STA.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.6.3.100.1.4

swDrvDfsTable

table
.1.3.6.1.4.1.16177.1.400.1.6.5.1 · 1 row entry · 5 columns
Open in standard view 
DFS driver statistics
swDrvDfsTableEntry entry .1.3.6.1.4.1.16177.1.400.1.6.5.1.1
DFS driver statistics
Indexes
swDrvDfsIndex
Column Syntax OID
swDrvDfsIndex
Entry index of table.
Integer32
Constraints:
range: 0-1
 .1.3.6.1.4.1.16177.1.400.1.6.5.1.1.1
swDrvDfsName
Name of the wireless device.

Applies to AP and STA. 802.11n products only.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.6.5.1.1.2
swDrvDfsPulsesDetected
Pulses detected by the wireless device.

Applies to AP. 802.11n products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.1.1.3
swDrvDfsPulsesProcessed
Pulses processed by the wireless device.

Applies to AP. 802.11n products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.1.1.4
swDrvDfsRadarDetected
Radar sequences detected by the wireless device.

Applies to AP. 802.11n products only.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.1.1.5

swDrvCntWlanMacTable

table
.1.3.6.1.4.1.16177.1.400.1.6.5.4 · 1 row entry · 20 columns
Open in standard view 
Wireless MAC layer statistics.
swDrvCntWlanMacTableEntry entry .1.3.6.1.4.1.16177.1.400.1.6.5.4.1
Wireless MAC layer statistics.
Indexes
swDrvCntWlanMacIndex
Column Syntax OID
swDrvCntWlanMacIndex
Entry index of table.
Integer32
Constraints:
range: 0-63
 .1.3.6.1.4.1.16177.1.400.1.6.5.4.1.1
swDrvCntWlanMacName
Name of the wireless device.

Applies to AP and STA. 802.11n products only.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.6.5.4.1.2
swDrvCntWlanMacTxHandlersDrop
MAC debug entry.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.4.1.3
swDrvCntWlanMacTxHandlersQueued
MAC debug entry.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.4.1.4
swDrvCntWlanMacTxHandlersDropUnencrypted
MAC debug entry.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.4.1.5
swDrvCntWlanMacTxHandlersDropFragment
MAC debug entry.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.4.1.6
swDrvCntWlanMacTxHandlersDropWep
MAC debug entry.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.4.1.7
swDrvCntWlanMacTxHandlersDropNotAssoc
MAC debug entry.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.4.1.8
swDrvCntWlanMacTxHandlersDropUnauthPort
MAC debug entry.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.4.1.9
swDrvCntWlanMacRxHandlersDrop
MAC debug entry.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.4.1.10
swDrvCntWlanMacRxHandlersQueued
MAC debug entry.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.4.1.11
swDrvCntWlanMacRxHandlersDropNullfunc
MAC debug entry.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.4.1.12
swDrvCntWlanMacRxHandlersDropDefrag
MAC debug entry.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.4.1.13
swDrvCntWlanMacRxHandlersDropShort
MAC debug entry.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.4.1.14
swDrvCntWlanMacTxExpandSkbHead
MAC debug entry.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.4.1.15
swDrvCntWlanMacTxExpandSkbHeadCloned
MAC debug entry.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.4.1.16
swDrvCntWlanMacRxExpandSkbHead
MAC debug entry.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.4.1.17
swDrvCntWlanMacRxExpandSkbHead2
MAC debug entry.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.4.1.18
swDrvCntWlanMacRxHandlersFragments
MAC debug entry.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.4.1.19
swDrvCntWlanMacTxstatusDrop
MAC debug entry.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.4.1.20

swDrvCntWlanWmmTable

table
.1.3.6.1.4.1.16177.1.400.1.6.5.6 · 1 row entry · 7 columns
Open in standard view 
WMM statistics.
swDrvCntWlanWmmTableEntry entry .1.3.6.1.4.1.16177.1.400.1.6.5.6.1
WMM statistics.
Indexes
swDrvCntWlanWmmTableIndex
Column Syntax OID
swDrvCntWlanWmmTableIndex
Entry index of table.
Integer32
Constraints:
range: 0-4
 .1.3.6.1.4.1.16177.1.400.1.6.5.6.1.1
swDrvCntWlanWmmName
Name of the queue.

Applies to AP and STA. 802.11n products only.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.6.5.6.1.2
swDrvCntWlanWmmTx
Number of frames sent in this queue.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.6.1.3
swDrvCntWlanWmmRx
Number of frames received in this queue.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.6.1.4
swDrvCntWlanWmmShortRetries
Number of retries for frames shorter than RTS.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.6.1.5
swDrvCntWlanWmmLongRetries
Number of retries for frames longer than RTS.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.6.1.6
swDrvCntWlanWmmExceededRetries
Number of failed transmissions due to exceeding of the retry limit.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.6.1.7

swDrvConStatTable

table
.1.3.6.1.4.1.16177.1.400.1.6.5.8 · 1 row entry · 24 columns
Open in standard view 
Connection Status Information.
swDrvConStatTableEntry entry .1.3.6.1.4.1.16177.1.400.1.6.5.8.1
Connection Status Information per Station.
Indexes
swDrvConStatIndex
Column Syntax OID
swDrvConStatIndex
Entry index of Table.
Integer32
Constraints:
range: 0-9
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.1
swDrvConStatWlanName
WLAN interface name.

Applies to AP and STA. 802.11n products only.
OctetString
Constraints:
range: 4-5
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.2
swDrvConStatMacName
Station MAC address.

In AP mode this is the MAC address of the connected
client (STA). In client (STA) mode this is the
MAC address of the AP to which the client is
connected.

Applies to AP…
OctetString
Constraints:
range: 1-17
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.3
swDrvConStatRxBrExtra
Station rx bitrate extra.

Applies to AP and STA. 802.11n products only.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.4
swDrvConStatRxBrType
Station rx bitrate type.

Applies to AP and STA. 802.11n products only.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.5
swDrvConStatRxBrValue
Station rx bitrate value.

Multiplied by 10 if `swDrvConStatRxBrType` is 'legacy'.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.6
swDrvConStatRxBytes
Station rx bytes.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.7
swDrvConStatRxPackets
Station rx packets.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.8
swDrvConStatTxBrExtra
Station tx bitrate extra.

Applies to AP and STA. 802.11n products only.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.9
swDrvConStatTxBrType
Station tx bitrate type.

Applies to AP and STA. 802.11n products only.
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.10
swDrvConStatTxBrValue
Station tx bitrate value.

Multiplied by 10 if `swDrvConStatTxBrType` is 'legacy'.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.11
swDrvConStatTxBytes
Station tx bytes.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.12
swDrvConStatTxPackets
Station tx packets.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.13
swDrvConStatSigChain0
Station signal chain 0 in dBm.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.14
swDrvConStatSigChain1
Station signal chain 1 in dBm.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.15
swDrvConStatSigChain2
Station signal chain 2 in dBm.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.16
swDrvConStatSigAvgChain0
Station signal average chain 0 in dBm.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.17
swDrvConStatSigAvgChain1
Station signal average chain 1 in dBm.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.18
swDrvConStatSigAvgChain2
Station signal average chain 2 in dBm.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.19
swDrvConStatTxRetries
Station tx retries.

Applies to AP and STA.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.20
swDrvConStatTxFailed
Station tx failed.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.21
swDrvConStatCacheNo
Station Dump Cache Access Number.

The cache gets refreshed if it is older than 5 seconds.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.22
swDrvConStatSigCombined
Station signal combined of all active chains in dBm.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.23
swDrvConStatSigAvgCombined
Station signal average combined of all active chains in dBm.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.16177.1.400.1.6.5.8.1.24

swDrvCntWlanTable

table
.1.3.6.1.4.1.16177.1.400.1.6.5.9 · 1 row entry · 16 columns
Open in standard view 
Wireless Dev Counters
swDrvCntWlanTableEntry entry .1.3.6.1.4.1.16177.1.400.1.6.5.9.1
Wireless Dev Counters
Indexes
swDrvCntWlanIndex
Column Syntax OID
swDrvCntWlanIndex
Entry index of Table
Integer32
Constraints:
range: 0-63
 .1.3.6.1.4.1.16177.1.400.1.6.5.9.1.1
swDrvCntWlanName
Name of the wireless Dev
OctetString
Constraints:
range: 1-255
 .1.3.6.1.4.1.16177.1.400.1.6.5.9.1.2
swDrvCntWlanAssocSuccess
Number of successful associations. 802.11n products only.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.16177.1.400.1.6.5.9.1.4
swDrvCntWlanAssocFailure
Number of unsuccessful associations. 802.11n products only.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.16177.1.400.1.6.5.9.1.5
swDrvCntWlanAssocFailureMaxSta
Number of times the maximum number of stations has been exceeded.

Applies to AP. 802.11n products only.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.16177.1.400.1.6.5.9.1.6
swDrvCntWlanNumAssocSta
Number of associated STA.

Applies to AP. 802.11n products only.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.16177.1.400.1.6.5.9.1.7
swDrvCntWlanEapAuthStarted
Number of EAP authentication sessions started since
the AP has been started.

Applies to AP. 802.11n products only.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.16177.1.400.1.6.5.9.1.8
swDrvCntWlanEapAuthFailed
Number of EAP authentication sessions that have
failed since the AP has been started.

Applies to AP. 802.11n products only.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.16177.1.400.1.6.5.9.1.9
swDrvCntWlanChannelActive
Time in ms during which the device has been on the current channel.

On STA when it's no associated the current channel is the lowest
channel of selected country code.

Applies to AP and STA.…
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.16177.1.400.1.6.5.9.1.10
swDrvCntWlanChannelBusy
Time in ms during which the medium has been considered busy on the
current channel.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.16177.1.400.1.6.5.9.1.11
swDrvCntWlanChannelTransmit
Time in ms during which the device has been in transmit mode on the
current channel.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.16177.1.400.1.6.5.9.1.12
swDrvCntWlanChannelReceive
Time in ms during which the device has been in receive mode on the
current channel.

Applies to AP and STA. 802.11n products only.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.16177.1.400.1.6.5.9.1.13
swDrvCntWlanChannelNoise
Measured channel noise in 1 dB steps.

**Notice:** This value is not an absolute power level but the
internal representation of the measured noise floor.

Applies to AP and STA. 802.11n produ…
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.16177.1.400.1.6.5.9.1.14
swDrvCntWlanEapAuthStartedFT
EAP sessions started through FT.

Applies to AP. 802.11n products only.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.16177.1.400.1.6.5.9.1.20
swDrvCntWlanEapAuthStartedFILS
EAP sessions started through FILS.

Applies to AP. 802.11n products only.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.16177.1.400.1.6.5.9.1.21
swDrvCntWlanEapAuthStartedPKMSA
EAP sessions started through PKMSA.

Applies to AP. 802.11n products only.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.16177.1.400.1.6.5.9.1.22