cfgWlanDevPower
WESTERMO-SW6-MIB ·
.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.8
Object
column
r/w
Integer32
Max. limit for wireless output power as effective isotropic radiated power
(EIRP) in dBm including array gain and antenna gain.
**Note:** This parameter only limits the maximum output power. The effective
output power might be lower (regulatory limits, rate depended limits).
EIRP (dBm) = antenna port power (dBm) + array gain (dB) + antenna gain (dBi)
- The antenna port power in dBm defines the power transmitted per antenna port
(chain).
- The array gain in dB defines the gain which is achieved by the use of multiple
antenna ports (chains). The number of active antenna ports (chains) is defined by
`cfgWlanDevTxAntenna`. The array gain depends on number of active antenna ports
(chains) as following:
- One antenna port (chain) = 0 dB
- Two antenna ports (chains) = 3 dB
- Three antenna ports (chains) = 5 dB
- Four antenna ports (chains) = 6 dB
- The antenna gain in dBi defines the gain which is achieved by the antenna.
The antenna gain is configured by `cfgWlanDevAntennaGain`.
Applies to AP and STA.
Context
- MIB
- WESTERMO-SW6-MIB
- OID
.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.8- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- cfgWlanDeviceTableEntry
- Table
- cfgWlanDeviceTable
- Siblings
- 16
Syntax
Integer32
Values & Constraints
Object Constraints
range: 6-50
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cfgWlanDevIndex Entry index of table. | column | Integer32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.1 |
| cfgWlanDevDistance Maximum distance in meters a client can be apart from the access
point. Even though the distance is set in meters, the slot time
settings change in 450m steps.
Appl… | column | Integer32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.10 |
| cfgWlanDevRts Frames equal or longer in bytes than this value require a
RTS/CTS handshake.
RTS/CTS is used in hidden node situations. In 11bg and b mode,
these frames are sent in… | column | Integer32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.11 |
| cfgWlanDevFragments Frames longer in bytes than this threshold will be fragmented.
Fragmentation can be used to reduce the number of retransmissions.
The following settings are special… | column | Integer32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.12 |
| cfgWlanDevShortRetry Number of times the transmission of the RTS frame will be retried
if there is no CTS received from the AP.
Applies to AP and STA. 802.11n products only. | column | Integer32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.13 |
| cfgWlanDevLongRetry Number of times the unicast data frames will be retried if there is
no ACK from the receiver.
Applies to AP and STA. 802.11n products only. | column | Integer32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.14 |
| cfgWlanDevAntennaGain Antenna gain in dBi.
If multiple antennas with different gains are connected, the value
of the antenna with the highest gain shall be configured.
App… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.15 |
| cfgWlanDevTxAntenna Configure the number of wireless transmission antenna ports.
This is a bitmask to enable/disable the chains.
**Example**
* 1(0001) = A… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.16 |
| cfgWlanDevRxAntenna Configure the number of wireless receiver antennas.
This is a bitmask to enable/disable the chains.
**Example**
* 1(0001) = A1 (chain … | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.17 |
| cfgWlanDevPhy The map between physical device and radio.
Applies to AP and STA. | column | OctetString | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.18 |
| cfgWlanDevName Name of the wireless device.
Applies to AP and STA. | column | OctetString | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.2 |
| cfgWlanDevHtCapabilities HT capability flags:
* [LDPC] = 1 Enable support for LDPC coding
* [SHORT-GI-20] = 32 Allow short GI for 20 MHz
* [SHORT-GI-40] = 64 Allow… | column | Integer32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.24 |
| cfgWlanDevQmrrString A list of rate controller quadruples per queue.
Each quadruple consist of
(mcs-rate [0-31], tries [0-15], rts_cts [0-1], sgi [0-1])
with 4 entries per queue.
… | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.26 |
| cfgWlanDevModulation The modulation modes of the physical wireless device are:
* **g(2):** This modulation mode uses OFDM data rates up
to 54 MBit/s in the frequency band between 2.4… | column | Enumeration | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.4 |
| cfgWlanDevBandwidth Wireless Bandwidth Mode specifies the Bandwidth of the Channel.
* **bw20(0):** for 20MHz wide channel.
* **bw40Plus(1):** for 40MHz wide channel with the side
cha… | column | Enumeration | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.5 |
| cfgWlanDevFrequency Wireless Frequency in MHz.
In AP mode, setting the wireless frequency to zero(0) enables the
automatic channel selection (ACS) feature. This forces the AP to choose… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.6 |