cfgWlanDevBandwidth
WESTERMO-SW6-MIB ·
.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.5
Object
column
r/w
Enumeration
Wireless Bandwidth Mode specifies the Bandwidth of the Channel.
* **bw20(0):** for 20MHz wide channel.
* **bw40Plus(1):** for 40MHz wide channel with the side
channel on the top.
* **bw40Minus(2):** for 40MHz wide channel with the side
channel on the bottom.
* **bwQuarter(3):** for 5MHz wide channel (quarter rate).
* **bwHalf(4):** for 10MHz wide channel (half rate).
* **bw80(5):** 80MHz wide channel (only in 11ac mode)
* **bw160(6):** 160MHz wide channel (only in 11ac mode)
* **bw8080(7):** 80+80MHz wide channel (only in 11ac mode)
* **bwAuto(8):** automatic channel width (only in 11ac mode)
**Note:** **bw40Plus(1)** and **bw40Minus(2)** may not be
usable on all channels.
**Examples**
The following table shows examples of which channels may be used.
The full list can be found in IEEE 802.11n Annex J. Depending on
the country, not all frequencies may be available.
| Band | **bw40Plus(1)** | **bw40Minus(2)** |
|------------|-------------------------|------------------------|
| 2.4 GHz | 2412 to 2452 | 2432 to 2472 |
| 5 GHz | 5180, 5220, 5260, etc. | 5200, 5240, 5280, etc. |
**Note:** Some products do not support all bandwidths.
Please check the data-sheet of your product.
Applies to AP and STA.
Context
- MIB
- WESTERMO-SW6-MIB
- OID
.1.3.6.1.4.1.16177.1.400.1.1.3.1.1.5- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- cfgWlanDeviceTableEntry
- Table
- cfgWlanDeviceTable
- Siblings
- 16
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | bw20 |
1 | bw40Plus |
2 | bw40Minus |
3 | bwQuarter |
4 | bwHalf |
5 | bw80 |
6 | bw160 |
7 | bw8080 |
8 | bwAuto |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cfgWlanDevIndex Entry index of table. | column | Integer32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.1 |
| cfgWlanDevDistance Maximum distance in meters a client can be apart from the access
point. Even though the distance is set in meters, the slot time
settings change in 450m steps.
Appl… | column | Integer32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.10 |
| cfgWlanDevRts Frames equal or longer in bytes than this value require a
RTS/CTS handshake.
RTS/CTS is used in hidden node situations. In 11bg and b mode,
these frames are sent in… | column | Integer32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.11 |
| cfgWlanDevFragments Frames longer in bytes than this threshold will be fragmented.
Fragmentation can be used to reduce the number of retransmissions.
The following settings are special… | column | Integer32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.12 |
| cfgWlanDevShortRetry Number of times the transmission of the RTS frame will be retried
if there is no CTS received from the AP.
Applies to AP and STA. 802.11n products only. | column | Integer32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.13 |
| cfgWlanDevLongRetry Number of times the unicast data frames will be retried if there is
no ACK from the receiver.
Applies to AP and STA. 802.11n products only. | column | Integer32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.14 |
| cfgWlanDevAntennaGain Antenna gain in dBi.
If multiple antennas with different gains are connected, the value
of the antenna with the highest gain shall be configured.
App… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.15 |
| cfgWlanDevTxAntenna Configure the number of wireless transmission antenna ports.
This is a bitmask to enable/disable the chains.
**Example**
* 1(0001) = A… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.16 |
| cfgWlanDevRxAntenna Configure the number of wireless receiver antennas.
This is a bitmask to enable/disable the chains.
**Example**
* 1(0001) = A1 (chain … | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.17 |
| cfgWlanDevPhy The map between physical device and radio.
Applies to AP and STA. | column | OctetString | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.18 |
| cfgWlanDevName Name of the wireless device.
Applies to AP and STA. | column | OctetString | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.2 |
| cfgWlanDevHtCapabilities HT capability flags:
* [LDPC] = 1 Enable support for LDPC coding
* [SHORT-GI-20] = 32 Allow short GI for 20 MHz
* [SHORT-GI-40] = 64 Allow… | column | Integer32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.24 |
| cfgWlanDevQmrrString A list of rate controller quadruples per queue.
Each quadruple consist of
(mcs-rate [0-31], tries [0-15], rts_cts [0-1], sgi [0-1])
with 4 entries per queue.
… | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.26 |
| cfgWlanDevModulation The modulation modes of the physical wireless device are:
* **g(2):** This modulation mode uses OFDM data rates up
to 54 MBit/s in the frequency band between 2.4… | column | Enumeration | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.4 |
| cfgWlanDevFrequency Wireless Frequency in MHz.
In AP mode, setting the wireless frequency to zero(0) enables the
automatic channel selection (ACS) feature. This forces the AP to choose… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.6 |
| cfgWlanDevPower Max. limit for wireless output power as effective isotropic radiated power
(EIRP) in dBm including array gain and antenna gain.
**Note:** This parameter only limits… | column | Integer32 | .1.3.6.1.4.1.16177.1.400.1.1.3.1.1.8 |