MX-R2-MIB Table View
Table-centric layout grouping table, row, and column objects.
Tables
9
Rows
9
Columns
107
r2Table
table.0.1875.1.100.100
·
1 row entry
·
10 columns
R2 Channel Associated Signaling (R2 CAS)
Configuration parameters related to the R2 channel associated
signaling (R2 CAS) on this managed device.
A row in table R2 Channel Associated Signaling (R2 CAS).
Indexes
r2Name
| Column | Syntax | OID | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
r2Name
Name
Name that identifies the interface. |
OctetString | .0.1875.1.100.100.1.100 |
||||||||||||||
|
r2ChannelRange
Channel Range
Defines the range of active bearer channels. |
OctetStringr/w Constraints: range: 1-10 |
.0.1875.1.100.100.1.200 |
||||||||||||||
|
r2ChannelAllocationStrategy
Channel Allocation Strategy
Defines the strategy for selecting bearer channels. Available strategies are: * Ascending: select the lowest-numbered non-busy bearer channel * Descendin… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.100.1.300 |
||||||||||||||
|
r2MaxActiveCalls
Maximum Active Calls
Defines the maximum number of active calls on the interface. Note: The special value 0 indicates no maximum number of active calls. |
Unsigned32r/w Constraints: range: 0-30 |
.0.1875.1.100.100.1.400 |
||||||||||||||
|
r2EncodingScheme
Encoding Scheme
Defines the voice encoding scheme in the bearer capabilities.This encoding scheme is used when initiating a call on the R2 side. The supported encoding schemes are G.711 u-Law and G.711 A-… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.100.1.500 |
||||||||||||||
|
r2LineSignaling
Line Signaling
Defines the protocol to use for the line signaling: * Q421-2BitsSignaling: R2 line signaling type ITU-U Q.421. Typically used for PCM systems. This signa… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.100.1.600 |
||||||||||||||
|
r2IncomingDigitSignaling
Incoming Digit Signaling
Defines the R2 incoming digit signaling method. * MfcR2: Multi Frequency Compelled - R2. * DtmfR2: Dual Tone Multi Frequency - R2. Digit signalin… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.100.1.750 |
||||||||||||||
|
r2OutgoingDigitSignaling
Outgoing Digit Signaling
Defines the R2 outgoing digit signaling method. * MfcR2: Multi Frequency Compelled - R2. * DtmfR2: Dual Tone Multi Frequency - R2. Digit signalin… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.100.1.760 |
||||||||||||||
|
r2CountrySelection
Country Selection
Identifies the country. * Brazil-R2: Brazil R2 setting. * Mexico-R2: Mexico R2 setting. * Argentina-R2: Argentina R2 setting. * SaudiArabia-R2: SaudiArabia R2 sett… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.100.1.800 |
||||||||||||||
|
r2DigitAttenuation
Digit Attenuation
Additional attenuation in dB for MFR2/DTMF digit generation. By default, MFR2/DTMF digit generation power is determined by country selection. This parameter provides a mean to reduce thi… |
Unsigned32r/w Constraints: range: 0-20 |
.0.1875.1.100.100.1.900 |
r2SignalingVariantsTable
table.0.1875.1.100.200
·
1 row entry
·
13 columns
R2 Signaling Variants
This table allows to override or retrieve the default country
settings for R2 signaling parameters. This table is effective
only if the OverrideDefault parameter is Enabled. If the
OverrideDefault parameter is Disabled, any change in this
table have no effects.
A row in table R2 Signaling Variants.
Indexes
r2SignalingVariantsInterfaceName
| Column | Syntax | OID | ||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
r2SignalingVariantsInterfaceName
Interface Name
Identifies the interface. |
OctetString | .0.1875.1.100.200.1.100 |
||||||||||||||||||||||
|
r2SignalingVariantsOverrideDefault
Override Default
Overrides the default settings of R2 Signaling parameters for the CountrySelection and InterfaceName. * Disable: The interface uses the default country configuration.… |
MX-TCMxEnableStater/w Textual Convention: MX-TCMxEnableState EnumerationType Values:
|
.0.1875.1.100.200.1.300 |
||||||||||||||||||||||
|
r2SignalingVariantsBitsCD
CD Bits
Settings of the C and D bits when the device transmits line signals. C and D bits of received line signals are ignored by the device. |
Integer32r/w Constraints: range: 0-12 |
.0.1875.1.100.200.1.400 |
||||||||||||||||||||||
|
r2SignalingVariantsDnisLength
DNIS Length
This parameter specifies the expected length of the DNIS. DNIS (Dialed Number Identification Service) is the called party or the destination number. If a variable length is defined, then the I… |
Unsigned32r/w Constraints: range: 0-20 |
.0.1875.1.100.200.1.500 |
||||||||||||||||||||||
|
r2SignalingVariantsAniLength
ANI Length
Defines the length of ANI (Automatic Number Identification) to be requested or sent. If a variable length ANI is used, the tone set in the R2ToneVariants.FwdGroup1EndOfAni parameter is sent to … |
Unsigned32r/w Constraints: range: 0-20 |
.0.1875.1.100.200.1.600 |
||||||||||||||||||||||
|
r2SignalingVariantsAniRequestEnable
ANI Request Enable
Defines whether or not ANI should be requested. ANI (Automatic Number Identification) is the calling party number. When ANI is requested, the calling party category followed by the actu… |
MX-TCMxEnableStater/w Textual Convention: MX-TCMxEnableState EnumerationType Values:
|
.0.1875.1.100.200.1.700 |
||||||||||||||||||||||
|
r2SignalingVariantsSendAniRequestAfterDnisDigits
Send ANI Request After DNIS Digits
When the AniRequestEnable parameter is Enabled, this parameter defines the number of DNIS (Dialed Number Identification Service) digits to be received before sending the… |
Unsigned32r/w Constraints: range: 0-10 |
.0.1875.1.100.200.1.800 |
||||||||||||||||||||||
|
r2SignalingVariantsCollectCallBlocked
Collect Call Blocked
Defines if the Collect Call Blockage Option is used. Two methods actually exist to do Collect Call Blockage. The first method refers to R2 signaling and how, through th… |
MX-TCMxEnableStater/w Textual Convention: MX-TCMxEnableState EnumerationType Values:
|
.0.1875.1.100.200.1.900 |
||||||||||||||||||||||
|
r2SignalingVariantsAniCategory
Category Group II Signal
Specifies the group II forward signal to be sent on receiving a calling party category request. This tone indicates the category of the calling party. * NatSubscr… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.200.1.920 |
||||||||||||||||||||||
|
r2SignalingVariantsLineFreeCategory
Line Free Group B signal
Specifies the group B backward signal to be sent by the incoming R2 register to indicate line free condition of the destination party. * LineFreeCharge : Called p… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.200.1.930 |
||||||||||||||||||||||
|
r2SignalingVariantsAniRestrictedEnable
ANI Restricted Enable
This parameter specifies the behaviour of the unit following the reception of a reject request after sending the Send next digit (ANI) request. The request is generally rejected when… |
MX-TCMxEnableStater/w Textual Convention: MX-TCMxEnableState EnumerationType Values:
|
.0.1875.1.100.200.1.950 |
||||||||||||||||||||||
|
r2SignalingVariantsIncomingDeclineMethod
Incoming Decline Method
Sets how to cancel a call attempt from R2 if the called party rejects the call when in Seizure Acknowledged state (waiting for answer). * Release: B bit is set to … |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.200.1.970 |
||||||||||||||||||||||
|
r2SignalingVariantsResetSpecific
Reset Specific
Resets specific settings of R2 Signaling parameters with the default country settings. This command is used to retrieve the default country configuration set in the CountrySelection paramet… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.200.1.1000 |
r2TimerVariantsTable
table.0.1875.1.100.300
·
1 row entry
·
28 columns
R2 Signaling Timer Variants
This table allows to override or retrieve the default country
setting for R2 Timers.
A row in table R2 Signaling Timer Variants.
Indexes
r2TimerVariantsInterfaceName
| Column | Syntax | OID | ||||
|---|---|---|---|---|---|---|
|
r2TimerVariantsInterfaceName
Interface Name
Identifies the interface. |
OctetString | .0.1875.1.100.300.1.100 |
||||
|
r2TimerVariantsOverrideDefault
Override Default
Overrides the default setting of R2 Timers for the CountrySelection and InterfaceName. * Disable: The interface uses the default country configuration. The configurat… |
MX-TCMxEnableStater/w Textual Convention: MX-TCMxEnableState EnumerationType Values:
|
.0.1875.1.100.300.1.300 |
||||
|
r2TimerVariantsSeizureAckTimeout
Seizure Ack Timeout
Maximum time an outgoing R2 register waits for the seizure acknowledgement signal after sending a seizure signal. This value is expressed in milliseconds (ms). |
Integer32r/w Constraints: range: 0-10000 |
.0.1875.1.100.300.1.400 |
||||
|
r2TimerVariantsFaultSeizureAckTimeout
Fault Seizure Ack Timeout
Maximum time an incoming R2 register waits for a seizure acknowledge failure condition to clear. This value is expressed in milliseconds (ms). |
Integer32r/w Constraints: range: 0-100000 |
.0.1875.1.100.300.1.500 |
||||
|
r2TimerVariantsDoubleSeizureTimeout
Double Seizure Timeout
Minimum time an outgoing R2 register waits after a double seizure is recognized before releasing the connection. This value is expressed in milliseconds (ms). |
Integer32r/w Constraints: range: 0-1000 |
.0.1875.1.100.300.1.600 |
||||
|
r2TimerVariantsDoubleAnswerTimeout
Double Answer Timeout
Maximum time an outgoing R2 register waits after receiving a clear-backward signal before releasing the connection. This value is expressed in milliseconds (ms). |
Integer32r/w Constraints: range: 0-90000 |
.0.1875.1.100.300.1.700 |
||||
|
r2TimerVariantsAnswerTimeout
Answer Timeout
Maximum time the answer signal AB=01 is applied before the clear backward signal AB=11 is sent. This parameter is generally used to reject collect calls (toll) and is only available if the … |
Integer32r/w Constraints: range: 0-8000 |
.0.1875.1.100.300.1.710 |
||||
|
r2TimerVariantsReAnswerTimeout
ReAnswer Timeout
Maximum time the clear backward signal AB=11 is applied before the answer signal AB=01 is reapplied again. This parameter is generally used to reject collect calls (toll) and is only avai… |
Integer32r/w Constraints: range: 0-8000 |
.0.1875.1.100.300.1.720 |
||||
|
r2TimerVariantsReleaseGuardTimeout
Release Guard Timeout
Maximum time an incoming R2 register waits after sending an idle line signal to prevent a new seizure of the line when a clear forward line signal is received. This va… |
Integer32r/w Constraints: range: 0-4000 |
.0.1875.1.100.300.1.800 |
||||
|
r2TimerVariantsInterCallGuardTimeout
Inter-call Guard Timeout
Maximum time an outgoing R2 register waits after receiving an idle line signal before attempting a new seizure of the line. This value is expressed in milliseconds … |
Integer32r/w Constraints: range: 0-15000 |
.0.1875.1.100.300.1.820 |
||||
|
r2TimerVariantsNoDigitTimeout
No Digit Detected Timeout
Maximum time an incoming R2 register waits before sending the congestion tone when no digits are received. This value is expressed in milliseconds (ms). |
Integer32r/w Constraints: range: 0-120000 |
.0.1875.1.100.300.1.830 |
||||
|
r2TimerVariantsCongestionToneGuardTimeout
Congestion Tone Guard Timeout
Maximum time an incoming R2 register waits after sending a congestion tone before sending a clear forward line signal and transits to the idle state. This valu… |
Integer32r/w Constraints: range: 0-200000 |
.0.1875.1.100.300.1.850 |
||||
|
r2TimerVariantsUnblockingTimeout
Unblocking Timeout
Maximum time a both-way trunk waits before assuming an idle state when a blocking condition is removed. This will prevent a too aggressive seizure of the trunk. This valu… |
Integer32r/w Constraints: range: 0-4000 |
.0.1875.1.100.300.1.900 |
||||
|
r2TimerVariantsAddressCompleteTimeout
Address Complete Timeout
The Address Complete Timeout is the maximum time that the caller waits for a reception of AddressComplete Tone after sending all ANI or DNIS Digits. This value is e… |
Integer32r/w Constraints: range: 0-20000 |
.0.1875.1.100.300.1.1000 |
||||
|
r2TimerVariantsWaitAnswerTimeout
Wait Answer Timeout
The maximal time that the caller waits for an Answer signal (ANSW) after receiving a Group B Line Free Signal Tone. This timer is effective only when the line is free. T… |
Integer32r/w Constraints: range: 0-600000 |
.0.1875.1.100.300.1.1100 |
||||
|
r2TimerVariantsDigitCompleteTimeout
Digit Complete Timeout
The maximal time that the caller waits for a Group I forward tone after sending either a Group A next Dnis digit, next Ani digit or next calling category Tone. This v… |
Integer32r/w Constraints: range: 0-10000 |
.0.1875.1.100.300.1.1200 |
||||
|
r2TimerVariantsWaitGroupBResponseCompleteTimeout
Wait Group B Response Complete Timeout
The maximal time that the caller waits for the confirmation of the end of the compelled sequence after receiving a Group B Signal Tone. The end of the compelled sequ… |
Integer32r/w Constraints: range: 0-30000 |
.0.1875.1.100.300.1.1300 |
||||
|
r2TimerVariantsWaitImmediateResponseCompleteTimeout
Wait Immediate Response Complete Timeout
The maximal time that the caller waits for the confirmation of the end of the compelled sequence after receiving a Group B Signal Tone. The end of the compelled se… |
Integer32r/w Constraints: range: 0-10000 |
.0.1875.1.100.300.1.1400 |
||||
|
r2TimerVariantsPlayToneGuardTimeout
Play Tone guard Timeout
The maximum time an incoming R2 registers waits after receiving the confirmation of the reception of the Group B Signal Tone before playing one of the calling tones in the caller d… |
Integer32r/w Constraints: range: 0-2000 |
.0.1875.1.100.300.1.1500 |
||||
|
r2TimerVariantsAcceptCallTimeout
Accept Call Timeout
Time that the unit waits to accept a R2 CAS call. This value is expressed in milliseconds (ms). |
Integer32r/w Constraints: range: 0-10000 |
.0.1875.1.100.300.1.1600 |
||||
|
r2TimerVariantsClearForwardGuardTimeout
Clear Forward Guard Timeout
The maximum time an outgoing R2 register waits after sending a clear forward line signal before transiting to the idle state. This value is expressed in millisec… |
Integer32r/w Constraints: range: 0-600000 |
.0.1875.1.100.300.1.1700 |
||||
|
r2TimerVariantsClearBackwardGuardTimeout
Clear Backward Guard Timeout
The maximum time an incoming R2 register waits after sending a clear backward line signal before sending the idle line signal and transit in the idle state. Thi… |
Integer32r/w Constraints: range: 0-600000 |
.0.1875.1.100.300.1.1800 |
||||
|
r2TimerVariantsFaultOnAnsweredGuardTimeout
Fault On Answered Guard Timeout
The maximum time an outgoing R2 register waits for the fault to clear before sending the clear forward line signal. In the case of recognition of bb = 0 while in the answer… |
Integer32r/w Constraints: range: 0-86400000 |
.0.1875.1.100.300.1.1900 |
||||
|
r2TimerVariantsFaultOnClearBackwardGuardTimeout
Fault On Clear Backward Guard Timeout
The maximum time an outgoing R2 register waits for the fault to clear before sending the clear forward line signal. In the case of recognition of bb = 0 while in the … |
Integer32r/w Constraints: range: 0-86400000 |
.0.1875.1.100.300.1.2000 |
||||
|
r2TimerVariantsFaultOnSeizeAckGuardTimeout
Fault On Seize Ack Guard Timeout
The maximum time an outgoing R2 register waits for the fault to clear before sending the clear forward line signal. In the case of recognition of bb = 0 while in the seize… |
Integer32r/w Constraints: range: 0-86400000 |
.0.1875.1.100.300.1.2100 |
||||
|
r2TimerVariantsFaultOnSeizeGuardTimeout
Fault On Seize Guard Timeout
The maximum time an outgoing R2 register waits for the fault to clear before sending the clear forward line signal. In the case of recognition of bb = 0 while in the seize sta… |
Integer32r/w Constraints: range: 0-86400000 |
.0.1875.1.100.300.1.2200 |
||||
|
r2TimerVariantsDeclineGuardTimeout
Decline Guard Timeout
Maximum time the AB=10 release signal is applied before sending the AB=11 clearback signal. This parameter applies when the IncomingDeclineMethod parameter is set to 'ClearBack' whil… |
Integer32r/w Constraints: range: 1000-2000 |
.0.1875.1.100.300.1.2250 |
||||
|
r2TimerVariantsResetSpecific
Reset Specific
Resets specific settings of R2 Timers parameters with the default country settings. This command is used to retrieve the default country configuration set in the CountrySelection parameter. |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.300.1.2300 |
.0.1875.1.100.400
·
1 row entry
·
9 columns
R2 Digit Timer Variants
This table allows to override or retrieve the default country
setting for R2 Digit Timers.
A row in table R2 Digit Timer Variants.
Indexes
r2DigitTimerVariantsInterfaceName
| Column | Syntax | OID | ||||
|---|---|---|---|---|---|---|
|
r2DigitTimerVariantsInterfaceName
Interface Name
Identifies the interface. |
OctetString | .0.1875.1.100.400.1.100 |
||||
|
r2DigitTimerVariantsOverrideDefault
Override Default
Overrides the default setting of R2 Digit timers for the CountrySelection and InterfaceName. * Disable: The interface uses the default country configuration. The conf… |
MX-TCMxEnableStater/w Textual Convention: MX-TCMxEnableState EnumerationType Values:
|
.0.1875.1.100.400.1.300 |
||||
|
r2DigitTimerVariantsMfCongestionToneDuration
MF Congestion Tone Duration
Allows the administrator to specifically configures the duration of the transmission of the congestion tone. The special value '0' sets the duration according to the R2DigitTim… |
Integer32r/w Constraints: range: 0-120000 |
.0.1875.1.100.400.1.350 |
||||
|
r2DigitTimerVariantsMfcPulseInterDigitTimeout
MFC Pulse Inter Digit Timeout
The minimum delay between the end of transmission of the last signal of the compelled cycle and the start of the next one. This value is expressed in milliseco… |
Integer32r/w Constraints: range: 0-1000 |
.0.1875.1.100.400.1.400 |
||||
|
r2DigitTimerVariantsMfcPulseMinOnTimeout
MFC Minimum Pulse OnTimeout
The minimum time a backward tone can be on from the backward perspective. This value is expressed in milliseconds (ms). |
Integer32r/w Constraints: range: 0-1000 |
.0.1875.1.100.400.1.500 |
||||
|
r2DigitTimerVariantsMfcMaxSequenceTimeout
MFC Maximum Sequence Timeout
The maximum time for a complete compelled signaling cycle from the forward perspective. This value is expressed in milliseconds (ms). |
Integer32r/w Constraints: range: 0-70000 |
.0.1875.1.100.400.1.600 |
||||
|
r2DigitTimerVariantsMfcMaxOnTimeout
MFC Maximum On Timeout
The maximum time a forward tone can be on from the forward perspective. This value is expressed in milliseconds (ms). |
Integer32r/w Constraints: range: 0-35000 |
.0.1875.1.100.400.1.700 |
||||
|
r2DigitTimerVariantsMfcMaxOffTimeout
MFC Maximum Off Timeout
The maximum time a forward tone can be off from the forward perspective. This value is expressed in milliseconds (ms). |
Integer32r/w Constraints: range: 0-35000 |
.0.1875.1.100.400.1.800 |
||||
|
r2DigitTimerVariantsResetSpecific
Reset Specific
Resets specific settings of R2 Digit Timers parameters with the default country settings. This command is used to retrieve the default country configuration set in the CountrySelection para… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.400.1.900 |
r2LinkTimerVariantsTable
table.0.1875.1.100.500
·
1 row entry
·
5 columns
R2 Link Timer Variants
This table allows to override or retrieve the default country
setting for R2 Link Timers.
A row in table R2 Link Timer Variants.
Indexes
r2LinkTimerVariantsInterfaceName
| Column | Syntax | OID | ||||
|---|---|---|---|---|---|---|
|
r2LinkTimerVariantsInterfaceName
Interface Name
Identifies the interface. |
OctetString | .0.1875.1.100.500.1.100 |
||||
|
r2LinkTimerVariantsOverrideDefault
Override Default
Overrides the default setting of R2 Link timers for the CountrySelection and InterfaceName. * Disable: The interface uses the default country configuration. The confi… |
MX-TCMxEnableStater/w Textual Convention: MX-TCMxEnableState EnumerationType Values:
|
.0.1875.1.100.500.1.300 |
||||
|
r2LinkTimerVariantsLinkActivationTimeout
Link Activation Timeout
The maximum time the unit waits for an activation indication coming from the physical link. The activation indication is used to indicate that the physical layer connection has bee… |
Integer32r/w Constraints: range: 0-10000 |
.0.1875.1.100.500.1.400 |
||||
|
r2LinkTimerVariantsLinkActivationRetryTimeout
Link Activation Retry Timeout
The maximum time the unit waits before attempting to reestablish the physical link. The attempt is made when the physical layer connection has been deactivated. … |
Integer32r/w Constraints: range: 0-10000 |
.0.1875.1.100.500.1.500 |
||||
|
r2LinkTimerVariantsResetSpecific
Reset Specific
Resets specific settings of R2 Link Timers parameters with the default country settings. This command is used to retrieve the default country configuration set in the CountrySelection param… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.500.1.600 |
r2ToneVariantsTable
table.0.1875.1.100.600
·
1 row entry
·
32 columns
R2 Signaling Tone Variants
This table allows to override or retrieve the default country
setting for R2 Tone variants in forward and backward group.
A row in table R2 Signaling Tone Variants.
Indexes
r2ToneVariantsInterfaceName
| Column | Syntax | OID | ||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
r2ToneVariantsInterfaceName
Interface Name
Identifies the interface. |
OctetString | .0.1875.1.100.600.1.100 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsOverrideDefault
Override Default
Overrides the default setting of R2 tone variants for the CountrySelection and InterfaceName. * Disable: The interface uses the default country configuration. The con… |
MX-TCMxEnableStater/w Textual Convention: MX-TCMxEnableState EnumerationType Values:
|
.0.1875.1.100.600.1.300 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsFwdGroup1EndOfDnis
Forward Group 1 EndOfDnis Tone
Specifies the forward Group 1 tone used to send after the DNIS digits. * None: No tone used. * I1..I15: Group 1 forward signal MF Tones |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.400 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsFwdGroup1EndOfAni
Forward Group 1 EndOfAni Tone
Specifies the forward Group 1 tone used to send after the ANI digits. * None: No tone used. * I1..I15: Group 1 forward signal MF Tones |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.500 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsFwdGroup1RestrictedAni
Forward Group 1 Restricted ANI Tone
Specifies the forward Group 1 tone used to reject a send next digit (ANI). This tone is generally used in response to the identification request when the caller party i… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.520 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupASendNextDnisDigit
Backward Group A SendNextDnisDigit Tone
Specifies the backward Group A tone used to request the next DNIS digit. * None: No tone used. * A1..A15: Group A backward signal MF Tones |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.600 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupASendPreviousDnisDigit
Backward Group A SendPreviousDnisDigit Tone
Specifies the backward Group A tone used to request the previous DNIS digit. * None: No tone used. * A1..A15: Group A backward signal MF Tones |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.700 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupASwitchToGroupII
Backward Group A BwdGroupASwitchToGroupII Tone
Specifies the backward Group A tone used to request to the caller a switch of Group II signals. * None: No tone used. * A1..A15: Group A b… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.800 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupANetworkCongestion
Backward Group A NetworkCongestion Tone
Specifies the backward Group A tone to be sent when a congestion network is detected. * None: No tone used. * A1..A15: Group A backward signal MF… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.900 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupASendCallingPartyCategory
Backward Group A SendCallingPartyCategory Tone
Specifies the backward Group A tone sent when the backward group requests the calling party category. * None: No tone used. * A1..A15: Gro… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.1000 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupAImmediateAccept
Backward Group A ImmediateAccept Tone
Specifies the backward Group A tone sent when the backward group accepts the call immediatly. * None: No tone used. * A1..A15: Group A backward sig… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.1100 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupASendDnisDigitNMinus2
Backward Group A BwdGroupASendDnisDigitNMinus2 Tone
Specifies the backward Group A tone used to request the previous - 1 DNIS digit. * None: No tone used. * A1..A15: Group A backward si… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.1200 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupASendDnisDigitNMinus3
Backward Group A BwdGroupASendDnisDigitNMinus3 Tone
Specifies the backward Group A tone used to request the previous - 2 DNIS digit. * None: No tone used. * A1..A15: Group A backward si… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.1300 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupARepeatAllDnis
Backward Group A BwdGroupARepeatAllDnis Tone
Specifies the backward Group A tone used to request all DNIS digits. * None: No tone used. * A1..A15: Group A backward signal MF Tones |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.1400 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupASendNextAniDigit
Backward Group A BwdGroupASendNextAniDigit Tone
Specifies the backward Group A tone used to request the next ANI digit. * None: No tone used. * A1..A15: Group A backward signal MF Tones |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.1500 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupASendCallingPartyCategorySwitchGroupC
Backward Group A
BwdGroupASendCallingPartyCategorySwitchGroupC Tone Specifies the backward Group A tone used to request the calling party category and then switch to Group C signals. * No… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.1550 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupBSendSit
Backward Group B BwdGroupBSendSpecialToneInformation Tone
Specifies the backward Group B tone used to send a special information tone. * None: No tone used. * B1..B15: Group B backward … |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.1600 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupBUserBusy
Backward Group B BwdGroupBUserBusy Tone
Specifies the backward Group B tone used to signal a user busy. * None: No tone used. * B1..B15: Group B backward signal MF Tones |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.1700 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupBNetworkCongestion
Backward Group B BwdGroupBNetworkCongestion Tone
Specifies the backward Group B tone used to signal a network congestion. * None: No tone used. * B1..B15: Group B backward signal MF Ton… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.1800 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupBUnassignedNumber
Backward Group B BwdGroupBUnassignedNumber Tone
Specifies the backward Group B tone used to signal an unassigned number. * None: No tone used. * B1..B15: Group B backward signal MF Tones |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.1900 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupBLineFreeCharge
Backward Group B BwdGroupBLineFreeCharge Tone
Specifies the backward Group B tone used to signal that the line is free and charge must be applied. * None: No tone used. * B1..B15: Group… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.2000 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupBSupplementaryLineFreeCharge
Backward Group B BwdGroupBSupplementaryLineFreeCharge Tone
Specifies a supplementary backward Group B tone used to detect that the line is free and charge must be applied. This is a supplementary (optionn… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.2100 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupBLineFreeNoCharge
Backward Group B BwdGroupBLineFreeNoCharge Tone
Specifies the backward Group B tone used to signal that the line is free and no charges must be applied. * None: No tone used. * B1..B15:… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.2200 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupBLineOutOfOrder
Backward Group B BwdGroupBLineOutOfOrder Tone
Specifies the backward Group B tone used to signal that the line is out of order. * None: No tone used. * B1..B15: Group B backward signal … |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.2300 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupBChangedNumber
Backward Group B BwdGroupBChangedNumber Tone
Specifies the backward Group B tone used to signal that the subscriber has changed number. * None: No tone used. * B1..B15: Group B backward… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.2350 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupCSendNextAniDigit
Backward Group C BwdGroupCSendNextAniDigit Tone
Specifies the backward Group C tone used to request the next ANI digit. * None: No tone used. * C1..C15: Group C backward signal MF Tones |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.2355 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupCRepeatAllDnisSwitchGroupA
Backward Group C BwdCRepeatAllDnisSwitchGroupA Tone
Specifies the backward Group C tone used to request all DNIS digits and then switch to Group A signals. * None: No tone used. * C1..C… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.2360 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupCSendNextDnisDigitSwitchGroupA
Backward Group C BwdCSendNextDnisDigitSwitchGroupA Tone
Specifies the backward Group C tone used to request the next DNIS digit and then switch to Group A signals. * None: No tone used. … |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.2365 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupCNetworkCongestion
Backward Group C BwdGroupCNetworkCongestion Tone
Specifies the backward Group C tone used to signal a network congestion. * None: No tone used. * C1..C15: Group C backward signal MF Ton… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.2370 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupCSendPreviousDnisDigitSwitchGroupA
Backward Group C BwdCSendPreviousDnisDigitSwitchGroupA Tone
Specifies the backward Group C tone used to request the previous DNIS digit and then switch to Group A signals. * None: No tone… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.2375 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsBwdGroupCSwitchGroupII
Backward Group C BwdCSwitchGroupII Tone
Specifies the backward Group C tone used to request to the caller a switch of Group II signals. * None: No tone used. * C1..C15: Group C backward… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.2380 |
||||||||||||||||||||||||||||||||
|
r2ToneVariantsResetSpecific
Reset Specific
Resets specific settings of R2 Tones parameters with the default country settings. This command is used to retrieve the default country configuration set in the CountrySelection parameter. |
Enumerationr/w Enumerated Values:
|
.0.1875.1.100.600.1.2400 |
bearerChannelInfoTable
table.0.1875.1.200.100
·
1 row entry
·
2 columns
Bearer Channel Info
Port-specific operational, statistics, and active call data
for B channels.
A row in table Bearer Channel Info.
Indexes
bearerChannelInfoIndex
| Column | Syntax | OID | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
bearerChannelInfoIndex
Index
Identifies the Bearer Channel.. |
OctetString | .0.1875.1.200.100.1.100 |
||||||||||
|
bearerChannelInfoState
State
The current call control state for this channel: * Idle: The channel is available * InUse: The channel is currently used * Maintenance: Maintenance state, temporarily unavailabl… |
Enumeration Enumerated Values:
|
.0.1875.1.200.100.1.200 |
physicalLinkInfoTable
table.0.1875.1.300.100
·
1 row entry
·
2 columns
Physical Link Information
The physical link information table contains status
information for all interfaces on this managed device.
A row in table Physical Link Information.
Indexes
physicalLinkInfoInterfaceName
| Column | Syntax | OID | ||||
|---|---|---|---|---|---|---|
|
physicalLinkInfoInterfaceName
Interface Name
Identifies the interface. |
OctetString | .0.1875.1.300.100.1.100 |
||||
|
physicalLinkInfoState
State
The layer 1 state for this interface: * Up: Layer 1 connectivity. * Down: No layer 1 connectivity. The interface might be in this state because no cable is plugged in or a pin… |
Enumeration Enumerated Values:
|
.0.1875.1.300.100.1.200 |
physicalLinkTable
table.0.1875.1.300.200
·
1 row entry
·
6 columns
Physical Link
The physical link table containing configuration and
operational parameters for all interfaces on this managed
device.
A row in table Physical Link.
Indexes
physicalLinkInterfaceName
| Column | Syntax | OID | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|
|
physicalLinkInterfaceName
Interface Name
Identifies the interface. |
OctetString | .0.1875.1.300.200.1.100 |
||||||||
|
physicalLinkLineCoding
Line Coding
Defines the transmission encoding of bits: * B8ZS: Bipolar with 8-Zeros Substitution (T1 lines) * HDB3: High-Density Bipolar Order 3 (E1 lines) * AMI: Alternate Mark Inver… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.300.200.1.200 |
||||||||
|
physicalLinkLineFraming
Line Framing
Defines the frame format: * SF: Super frame. Sometimes known as D4 (T1 lines) * ESF: Extended super frame (T1 lines) * CRC4: Cyclic redundancy check 4 (E1 lines) * NO-C… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.300.200.1.300 |
||||||||
|
physicalLinkClockMode
Clock Mode
A port can either generate the clocking for the line or accept the clock from the line. The options master or slave determine the clocking method: * Master: Generates clock *… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.300.200.1.400 |
||||||||
|
physicalLinkMonitorLinkStateEnable
Monitor Link State Enable
Monitors the physical link state of an R2 interface. Enable: An R2 endpoint's operational state is affected by its interface physical link state. When the link sta… |
MX-TCMxEnableStater/w Textual Convention: MX-TCMxEnableState EnumerationType Values:
|
.0.1875.1.300.200.1.500 |
||||||||
|
physicalLinkPortPinout
Port Pinout
Defines the port pinout: * Auto: The pinout is set according to the clock mode. * Master: Force the pinout to Master regardless of the clock mode. * Slave: Force the p… |
Enumerationr/w Enumerated Values:
|
.0.1875.1.300.200.1.600 |