r2SignalingVariantsIncomingDeclineMethod
MX-R2-MIB ·
.0.1875.1.100.200.1.970
Object
column
r/w
Enumeration
Incoming Decline Method
Sets how to cancel a call attempt from R2 if the called party
rejects the call when in Seizure Acknowledged state (waiting
for answer).
* Release: B bit is set to 0 and state is set to Released.
* ClearBack: B bit is set to 0 until decline guard expires
then B bit is set to 1 and state is set to Clear-back.
See also R2TimerVariants.DeclineGuardTimeout parameter.
Context
- MIB
- MX-R2-MIB
- OID
.0.1875.1.100.200.1.970- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- r2SignalingVariantsEntry
- Table
- r2SignalingVariantsTable
- Siblings
- 12
Syntax
Enumeration
Values & Constraints
Enumerated Values
100 | release |
200 | clearBack |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| r2SignalingVariantsInterfaceName Interface Name
Identifies the interface. | column | OctetString | .0.1875.1.100.200.1.100 |
| r2SignalingVariantsResetSpecific Reset Specific
Resets specific settings of R2 Signaling parameters with the
default country settings. This command is used to retrieve
the default country configura… | column | Enumeration | .0.1875.1.100.200.1.1000 |
| r2SignalingVariantsOverrideDefault Override Default
Overrides the default settings of R2 Signaling parameters for
the CountrySelection and InterfaceName.
* Disable: The interface use… | column | MX-TCMxEnableState | .0.1875.1.100.200.1.300 |
| r2SignalingVariantsBitsCD CD Bits
Settings of the C and D bits when the device transmits line
signals. C and D bits of received line signals are ignored by
the device. | column | Integer32 | .0.1875.1.100.200.1.400 |
| r2SignalingVariantsDnisLength DNIS Length
This parameter specifies the expected length of the DNIS.
DNIS (Dialed Number Identification Service) is the called
party or the destination number. If … | column | Unsigned32 | .0.1875.1.100.200.1.500 |
| r2SignalingVariantsAniLength ANI Length
Defines the length of ANI (Automatic Number Identification)
to be requested or sent. If a variable length ANI is used,
the tone set in the R2ToneVariants… | column | Unsigned32 | .0.1875.1.100.200.1.600 |
| r2SignalingVariantsAniRequestEnable ANI Request Enable
Defines whether or not ANI should be requested. ANI
(Automatic Number Identification) is the calling party
number. When ANI is requested, the cal… | column | MX-TCMxEnableState | .0.1875.1.100.200.1.700 |
| r2SignalingVariantsSendAniRequestAfterDnisDigits Send ANI Request After DNIS Digits
When the AniRequestEnable parameter is Enabled, this
parameter defines the number of DNIS (Dialed Number
Identification Service) … | column | Unsigned32 | .0.1875.1.100.200.1.800 |
| r2SignalingVariantsCollectCallBlocked Collect Call Blocked
Defines if the Collect Call Blockage Option is used.
Two methods actually exist to do Collect Call Blockage. The
first method re… | column | MX-TCMxEnableState | .0.1875.1.100.200.1.900 |
| r2SignalingVariantsAniCategory Category Group II Signal
Specifies the group II forward signal to be sent on receiving
a calling party category request. This tone indicates the
category of the cal… | column | Enumeration | .0.1875.1.100.200.1.920 |
| r2SignalingVariantsLineFreeCategory Line Free Group B signal
Specifies the group B backward signal to be sent by the
incoming R2 register to indicate line free condition of the
destination party.
… | column | Enumeration | .0.1875.1.100.200.1.930 |
| r2SignalingVariantsAniRestrictedEnable ANI Restricted Enable
This parameter specifies the behaviour of the unit following
the reception of a reject request after sending the Send next
digit (ANI) request… | column | MX-TCMxEnableState | .0.1875.1.100.200.1.950 |