r2SignalingVariantsAniLength
MX-R2-MIB ·
.0.1875.1.100.200.1.600
Object
column
r/w
Unsigned32
ANI Length
Defines the length of ANI (Automatic Number Identification)
to be requested or sent. If a variable length ANI is used,
the tone set in the R2ToneVariants.FwdGroup1EndOfAni
parameter is sent to indicate the end of the ANI digits. When
fixed length ANI is used and the available ANI digits are
longer than the requested length, the last n digits are sent.
If available ANI digits are shorter, then the
R2ToneVariants.FwdGroup1EndOfAni parameter tone is sent.
* 0: Variable ANI length.
* 1..20: Specific ANI length.
Context
- MIB
- MX-R2-MIB
- OID
.0.1875.1.100.200.1.600- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- r2SignalingVariantsEntry
- Table
- r2SignalingVariantsTable
- Siblings
- 12
Syntax
Unsigned32
Values & Constraints
Object Constraints
range: 0-20
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| r2SignalingVariantsInterfaceName Interface Name
Identifies the interface. | column | OctetString | .0.1875.1.100.200.1.100 |
| r2SignalingVariantsResetSpecific Reset Specific
Resets specific settings of R2 Signaling parameters with the
default country settings. This command is used to retrieve
the default country configura… | column | Enumeration | .0.1875.1.100.200.1.1000 |
| r2SignalingVariantsOverrideDefault Override Default
Overrides the default settings of R2 Signaling parameters for
the CountrySelection and InterfaceName.
* Disable: The interface use… | column | MX-TCMxEnableState | .0.1875.1.100.200.1.300 |
| r2SignalingVariantsBitsCD CD Bits
Settings of the C and D bits when the device transmits line
signals. C and D bits of received line signals are ignored by
the device. | column | Integer32 | .0.1875.1.100.200.1.400 |
| r2SignalingVariantsDnisLength DNIS Length
This parameter specifies the expected length of the DNIS.
DNIS (Dialed Number Identification Service) is the called
party or the destination number. If … | column | Unsigned32 | .0.1875.1.100.200.1.500 |
| r2SignalingVariantsAniRequestEnable ANI Request Enable
Defines whether or not ANI should be requested. ANI
(Automatic Number Identification) is the calling party
number. When ANI is requested, the cal… | column | MX-TCMxEnableState | .0.1875.1.100.200.1.700 |
| r2SignalingVariantsSendAniRequestAfterDnisDigits Send ANI Request After DNIS Digits
When the AniRequestEnable parameter is Enabled, this
parameter defines the number of DNIS (Dialed Number
Identification Service) … | column | Unsigned32 | .0.1875.1.100.200.1.800 |
| r2SignalingVariantsCollectCallBlocked Collect Call Blocked
Defines if the Collect Call Blockage Option is used.
Two methods actually exist to do Collect Call Blockage. The
first method re… | column | MX-TCMxEnableState | .0.1875.1.100.200.1.900 |
| r2SignalingVariantsAniCategory Category Group II Signal
Specifies the group II forward signal to be sent on receiving
a calling party category request. This tone indicates the
category of the cal… | column | Enumeration | .0.1875.1.100.200.1.920 |
| r2SignalingVariantsLineFreeCategory Line Free Group B signal
Specifies the group B backward signal to be sent by the
incoming R2 register to indicate line free condition of the
destination party.
… | column | Enumeration | .0.1875.1.100.200.1.930 |
| r2SignalingVariantsAniRestrictedEnable ANI Restricted Enable
This parameter specifies the behaviour of the unit following
the reception of a reject request after sending the Send next
digit (ANI) request… | column | MX-TCMxEnableState | .0.1875.1.100.200.1.950 |
| r2SignalingVariantsIncomingDeclineMethod Incoming Decline Method
Sets how to cancel a call attempt from R2 if the called party
rejects the call when in Seizure Acknowledged state (waiting
for answer).
… | column | Enumeration | .0.1875.1.100.200.1.970 |