CISCO-LWAPP-AP-MIB Table View

Column Syntax OID

This object represents the radio MAC address
common to the dot11 interfaces of the AP
and uniquely identifies an entry in this table.

Type Constraints:
range: 6

Description:

Represents an 802 MAC address represented in the
`canonical' order defined by IEEE 802.1a, i.e., as if it
were transmitted least significant bit first, even though
802.5 (in contrast to other 802.x protocols) requires M…

.1.3.6.1.4.1.9.9.513.1.1.1.1.1

cLApIfMacAddress

This object represents the Ethernet MAC address of
the AP.

cLApMaxNumberOfDot11Slots

Type Constraints:
range: 6

Description:

.1.3.6.1.4.1.9.9.513.1.1.1.1.2

This object represents the maximum number of
802.11 radio interface slots in this AP.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.3

cLApEntPhysicalIndex

This object provides the index value in the
entPhysicalEntry corresponding to this AP.

ENTITY-MIBPhysicalIndex

Type Constraints:
range: 1..2147483647

.1.3.6.1.4.1.9.9.513.1.1.1.1.4

cLApName

This object specifies the administrative name
assigned to the AP by the user. If an AP is not configured,
its factory default name will be ap:<last three byte
of MACAddress> eg. ap:af:12:be.

OctetStringr/w

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.1.1.1.5

cLApUpTime

This object represents the time in hundredths
of a second since the last time the AP rebooted.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.6

cLLwappUpTime

This object represents the time in hundredths
of a second since the last time the AP joined
the controller.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.7

cLLwappJoinTakenTime

This object represents the time taken in hundredths
of a second for the AP to join the controller. This
could be a significant value in Mesh environments.

cLApMaxNumberOfEthernetSlots

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.8

This object represents the maximum number of
Ethernet slots in this AP.

cLApPrimaryControllerAddressType

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.9

This object specifies the type of the primary
controller's address made available through
cLApPrimaryControllerAddress.

cLApPrimaryControllerAddress

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.9.9.513.1.1.1.1.10

This object specifies the address of the primary
controller that the APs will join.

cLApSecondaryControllerAddressType

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.1.1.11

This object specifies the type of the secondary
controller's address made available through
cLApSecondaryControllerAddress.

cLApSecondaryControllerAddress

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.9.9.513.1.1.1.1.12

This object specifies the address of the secondary
controller that the APs will join.

cLApTertiaryControllerAddressType

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.1.1.13

This object specifies the type of the tertiary
controller's address made available through
cLApTertiaryControllerAddress.

cLApTertiaryControllerAddress

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.9.9.513.1.1.1.1.14

This object specifies the address of the tertiary
controller that the APs will join.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.1.1.15

cLApLastRebootReason

This object represents the reason for the last
reboot of the AP.
none - ap reported a reboot reason code
unknown to the controller.
dot11gModeChange …

Enumeration

Enumerated Values:

0	none
1	dot11gModeChange
2	ipAddressSet
3	ipAddressReset
4	rebootFromController
5	dhcpFallbackFail
6	discoveryFail
7	noJoinResponse
8	denyJoin
9	noConfigResponse
10	configController
11	imageUpgradeSuccess
12	imageOpcodeInvalid
13	imageCheckSumInvalid
14	imageDataTimeout
15	configFileInvalid
16	imageDownloadError
17	rebootFromConsole
18	rapOverAir
19	powerLow
20	crash
21	powerHigh
22	powerLoss
23	powerChange
24	componentFailure
25	watchdog
26	lscEnabled
27	lscDisabled
28	lscProvTimeout
29	lscMaxProvReqRetries
30	lscLoadFailure
31	lscJoinFailure
32	capwapTimerFailure
33	staticIpFailover
34	vlanTagFailover
35	capwapDiscoveryRequest
36	capwapDiscoveryResponse
37	capwapJoinRequest
38	capwapJoinResponse
39	capwapConfigurationStatus
40	capwapConfigurationStatusResponse
41	capwapConfigurationUpdateRequest
42	capwapConfigurationUpdateResponse
43	capwapWtpEventRequest
44	capwapWtpEventResponse
45	capwapChangeStateEventRequest
46	capwapChangeStateEventResponse
47	capwapEchoRequest
48	capwapEchoResponse
49	capwapImageDataRequest
50	capwapImageDataResponse
51	capwapResetRequest
52	capwapResetResponse
53	capwapPrimaryDiscoveryRequest
54	capwapPrimaryDiscoveryResponse
55	capwapDataTransferRequest
56	capwapDataTransferResponse
57	capwapClearConfigurationRequest
58	capwapClearConfigurationResponse
59	capwapMobileConfigurationRequest
60	capwapMobileConfigurationResponse
61	capwapPathMtuRequest
62	capwapPathMtuResponse
63	vlanTagRetry
64	ipv6AddrSet
65	modeChange
66	typeChangedToCapwap
67	typeChangedToMe
68	eraseCfgCommand
69	oeapModeCfgUpload
70	lagCfg
71	fipsModeChange
72	diminishedPowerChange
73	slubDebug
74	lscModeCapwap
75	lscModeDot1x
76	lscModeAll
77	apTypeCloud
78	dtlsInitFailure
79	pnpNoCapwapBackOff
80	day0CfgFail
81	day1CfgFail
82	pnpTriggeredReload
83	triRadioSupport
84	indoorDeployment
85	apTypeWgbToCapwap
86	apTypeCloudToCapwap
87	apTypeWgb

.1.3.6.1.4.1.9.9.513.1.1.1.1.16

cLApEncryptionEnable

This object specifies whether encyrption between
controller and AP is enabled or not. Encryption
can only be enabled if ESM card in controller is
pluged in.

A value of 'true' enables encryption between
…

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.18

cLApFailoverPriority

This object specifies the AP failover priority
for an AP. If a higher priority AP wishes to join
the controller, it will be given preference over
a join request from a lower priority AP. Also if the
number of AP join…

Enumerationr/w

Enumerated Values:

1	low
2	medium
3	high
4	critical

.1.3.6.1.4.1.9.9.513.1.1.1.1.19

cLApPowerStatus

This object represents the power status of the AP
low - The AP is drawing low power from
Ethernet
fifteendotfour - The AP is drawing 15.4 watts from
Ethernet
sixteendo…

Enumeration

Enumerated Values:

1	low
2	fifteendotfour
3	sixteendoteight
4	full
5	external
6	twentyfivedotfive
7	mixedmode

.1.3.6.1.4.1.9.9.513.1.1.1.1.20

cLApTelnetEnable

This object specifies whether telnet session
can be established to the AP.

A value of 'true' indicates an telnet session
can be established to the AP.

A value of 'false' indicates an teln…

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.21

cLApSshEnable

This object specifies whether SSH session
can be established to the AP.

A value of 'true' indicates an SSH session
can be established to the AP.

A value of 'false' indicates an SSH sessio…

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.22

cLApPreStdStateEnabled

This object specifies whether the pre-standard state
of the AP is enabled or disabled.

A value of 'true' indicates that the pre-standard state
of the AP is enabled,

A value of 'false' indic…

cLApPwrInjectorStateEnabled

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.23

This object specifies whether the power injector state
of the AP is enabled or disabled.

A value of 'true' indicates that the power injector state
of the AP is enabled,

A value of 'false' i…

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.24

cLApPwrInjectorSelection

This object specifies the power injector selection
value of the AP.

'unknown' - is returned if
'cLApPwrInjectorStateEnabled'is set to false.
'installed' - configure the MAC address of the
…

Enumerationr/w

Enumerated Values:

1	unknown
2	installed
3	override

.1.3.6.1.4.1.9.9.513.1.1.1.1.25

cLApPwrInjectorSwMacAddr

This object specifies the MAC address of the
switch port that has a power Injector and is
valid only when the 'cLApPwrInjectorSelection'
is in 'installed' mode.
if SET to 00:00:00:00:00:00, AP will detect the
MAC add…

SNMPv2-TCMacAddressr/w

Type Constraints:
range: 6

Description:

.1.3.6.1.4.1.9.9.513.1.1.1.1.26

cLApWipsEnabledeprecated

This object represents if this AP is used
as WIPS AP.
A value of 'true' indicates that this AP is
a WIPS AP.
A value of 'false' indicates that this AP is
not a WIPS AP. This applies only when the
AP is either in local …

cLApMonitorModeOptimization

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.27

This object specifies the monitor mode optimization
on this device.
all - All optimization is enabled
tracking - Tracking is optimized
wips - WIPS optimization is enabled
none - No optimiz…

Enumerationr/w

Enumerated Values:

1	all
2	tracking
3	wips
4	none

.1.3.6.1.4.1.9.9.513.1.1.1.1.28

cLApDomainName

This object specifies the domain, to which the AP belongs.
This attribute can be configured only if the static IP
option is turned on in the AP.

cLApNameServerAddressType

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.1.1.29

This object specifies the type of the IP address of the
name server, made available through cLApNameServerAddress.

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.9.9.513.1.1.1.1.30

cLApNameServerAddress

This object specifies the IP Address of the name server.
This attribute can be configured only if the static IP
option is turned on in the AP.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.1.1.31

cLApAMSDUEnable

This object specifies the AMSDU status.
A value of 'true' indicates AMSDU is enabled.
A value of 'false' indicates AMSDU is disabled.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.32

cLApEncryptionSupported

This object specifies whether AP Supports
DTLS encryption.
A value of 'true' indicates encryption is supported.
A value of 'false' indicates encryption is not supported.

cLApRogueDetectionEnabled

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.33

This object specifies whether Rogue Detection
is enabled in this AP.
A value of 'true' indicates rogue detection is enabled.
A value of 'false' indicates rogue detection is disabled.
Rogue detection is …

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.34

cLApTcpMss

This object specifies the TCP Maximum Segment Size
for this AP.
Permissible value are between 536 and 1363. This will
also enable the TCP MSS flag for this AP.
Value of 0 will disable the TCP MSS flag for this AP.
Any c…

Integer32r/w

Constraints:
range: 0-0
range: 536-1363

.1.3.6.1.4.1.9.9.513.1.1.1.1.35

cLApDataEncryptionStatus

This object represents the data encryption
status of AP.

A value of 'true' indicates data is encrypted between
AP and WLC.

A value of 'false' indicates data is plain text be…

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.36

cLApNsiKey

This object represents the network spectrum interface key
used when the AP is in spectrum expert Only monitor mode
(SOMM).This object returns a non-zero value only when the
AP is SOMM mode.

OctetString

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.1.1.1.37

cLApAdminStatus

This object specifies the admin state of the AP,
A value of 'true' indicates AP admin status is up.
A value of 'false' indicates AP admin status is down.

INET-ADDRESS-MIBInetPortNumber

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.38

cLApPortNumber

This object represents the port number on which
the AP's traffic is coming through.

Type Constraints:
range: 0..65535

.1.3.6.1.4.1.9.9.513.1.1.1.1.39

cLApRetransmitCount

This object specifies the retransmission count for the access
point control packet.This value specifies the number of packets
retransmitted after which the Access Point falls back to another
controller in case of failov…

retriesSNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.40

cLApRetransmitTimeout

This object specifies the retransmission timeout for the access
point control packet. This value specifies the timeout for each
retransmission, during the fallback of access point to another
controller in case of failo…

secondsSNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.41

cLApVenueConfigVenueGroup

This object specifies the venue group
for this WLAN.

Enumerationr/w

Enumerated Values:

1	unspecified
2	assembly
3	business
4	educational
5	factoryAndIndustrial
6	institutional
7	mercantile
8	residential
9	storage
10	utilityAndMisc
11	vehicular
12	outdoor

.1.3.6.1.4.1.9.9.513.1.1.1.1.42

cLApVenueConfigVenueType

This object specifies the venue type within
a particular venue group,for this WLAN.
The venue group-venue type relationship is per
the following table:
Venue Group Venue Type Code Venue Description
=========== =========…

Enumerationr/w

Enumerated Values:

1	unspecified
2	unspecifiedAssembly
3	arena
4	stadium
5	passengerTerminal
6	amphitheater
7	amusementPark
8	placeOfWorship
9	conventionCenter
10	library
11	museum
12	restaurant
13	theater
14	bar
15	coffeeShop
16	zooOrAquarium
17	emergencyCoordinationCenter
18	unspecifiedBusiness
19	doctorOrDentistOffice
20	bank
21	fireStation
22	policeStation
23	postOffice
24	professionalOffice
25	researchAndDevelopmentFacility
26	attorneyOffice
27	unspecifiedEducational
28	schoolPrimary
29	schoolSecondary
30	universityOrCollege
31	unspecifiedFactoryAndIndustrial
32	factory
33	unspecifiedInstitutional
34	hospital
35	longTermCareFacility
36	alcoholAndDrugRehabilitationCenter
37	groupHome
38	prisonOrJail
39	unspecifiedMercantile
40	retailStore
41	groceryMarket
42	atomotiveServiceStation
43	shoppingMall
44	gasStation
45	unspecifiedResidential
46	privateResidence
47	hotelOrMotel
48	dormitory
49	boardingHouse
50	unspecifiedStorage
51	unspecifiedUtility
52	unspecifiedVehicular
53	automobileOrTruck
54	airplane
55	bus
56	ferry
57	shipOrBoat
58	train
59	motorBike
60	unspecifiedOutdoor
61	muniMeshNetwork
62	cityPark
63	restArea
64	trafficControl
65	busStop
66	kiosk

.1.3.6.1.4.1.9.9.513.1.1.1.1.43

cLApVenueConfigVenueName

This object specifies the venue name defined for this AP
group.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.1.1.44

cLApVenueConfigLanguage

This object specifies the language defined for this AP group.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.1.1.45

cLApLEDState

This object specifies whether the LED state of this access
point should be enabled or disabled.
A value of 'true' indicates LED status is enabled.
A value of 'false' indicates LED status is disabled.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.46

cLApTrunkVlan

This object specifies the trunk VLAN ID
assigned to this AP's ethernet interface.
When a non-zero value is assigned for this
Object, the management packets will be
tagged with this VLAN ID. When the value of
trunk VLAN…

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.47

cLApTrunkVlanStatus

This object specifies whether the trunk VLAN ID
assigned to this AP's is effective. If the AP is unable
to route the management frames through the trunk
vlan, it will revert back to untagged mode. A value of
true indi…

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.48

cLApLocation

This object specifies the user specified location of this AP.
While configuring AP, user should specify a location for
the AP so that its easy to figure out for some one where
the AP is located.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.1.1.49

cLApSubMode

This object specifies the sub mode of the AP.
The option 'wips' applies only when the
AP is in local, flexConnect or monitor mode.
This 'pppoe' options apply only when the
AP is in flexConnect mode.

Enumerationr/w

Enumerated Values:

1	none
2	wips
3	pppoe
4	pppoeWips

.1.3.6.1.4.1.9.9.513.1.1.1.1.50

cLApAssocCount

This object specifies the association count for the access
point. This counter includes both successful and failed
associate attempts, but does NOT include the re-associate
attempts.

cLApAssocFailResourceCount

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.51

This object specifies the association failure count for the
access point due to the resource limits, i.e. the max clients
of the WLAN/Radio is reached.

cLApRealTimeStatsModeEnabled

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.52

This object specifies whether current stats mode is
'realtime'. There are two stats-mode, realtime and normal which
specifies the stats-timer range to be 10-180 sec and 2-5 sec
each.
A value of 'true' indicates curren…

cLApAssociatedClientCount

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.53

This object represents the associated client number for the
access point.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.54

cLApMemoryCurrentUsage

This object represents the percent of current memory usage
of the access point.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.55

cLApMemoryAverageUsage

This object represents the percent of average memory usage
of the access point. The statistics window is defined by
clsSysStatisticsInterval.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.56

cLApCpuCurrentUsage

This object represents the percent of current CPU usage
of the access point.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.57

cLApCpuAverageUsage

This object represents the percent of average CPU usage
of the access point. The statistics window is defined by
clsSysStatisticsInterval.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.58

cLApUpgradeFromVersion

This object represents the AP image upgrade
from version.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.1.1.59

cLApUpgradeToVersion

This object represents the AP image upgrade
to version.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.1.1.60

cLApUpgradeFailureCause

This object represents the cause of the
AP image upgrade failure.

cLApMaxClientLimitNumberTrap

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.1.1.61

This object represents the max client limit number.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.62

cLApMaxClientLimitCause

This object represents the cause of the
max client limit reach.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.1.1.63

cLApMaxClientLimitSet

This object represents whether this event is
raised or cleared.
A value of 'true' indicates this event is set.
A value of 'false' indicates this even is cleared.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.64

cLApFloorLabel

This object specifies the floor label for the Access Point.

CISCO-TCUnsigned64r/w

.1.3.6.1.4.1.9.9.513.1.1.1.1.65

cLApConnectCountdeprecated

This object represents the Count of AP's that are connected
to the Controller.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.66

cLApReassocSuccCount

This object represents the successful re-association
count for the Access Point.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.67

cLApReassocFailCount

This object represents the failed re-association
count for the Access Point.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.68

cLAdjChannelRogueEnableddeprecated

This object specifies if rogue AP
detection and removed Traps need to be sent.
A value of 'true' indicates adjacent rogue detection
is enabled.
A value of 'false' indicates adjacent rogue detection
is disabled.
To Enab…

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.69

cLApAssocFailCountByRate

This object represents the failed association
count for the access point caused by rate mismatch.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.70

cLApAbnormalOfflineCount

This object represents the abnormal offline count for the
access point.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.71

cLApActiveClientCount

This object represents the active client number for the access
point.

cLApAssocFailCountForRssiLow

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.72

This object represents the failed association
count for the access point caused by RSSI low.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.73

cLApSysNetId

This object specifies the ApSysNetId which is the numeric
string to identify the system information like ApName.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.1.1.74

cLApAssocFailTimes

This object represents the counts of client failed association
to the access point.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.75

cLApAntennaBandMode

This object specifies the mode of antenna band.
notApplicable - will return for unsuppported APs.
single - configure the AP to use single band for antenna.
dual - configure the AP to use both bands for antenna.

Enumerationr/w

Enumerated Values:

1	notApplicable
2	single
3	dual

.1.3.6.1.4.1.9.9.513.1.1.1.1.76

cLApHeartBeatRspAvgTime

This object represents the average interval between sending
the echo request and receiving the echo response in AP.

millisecondsInteger32

Constraints:
range: 1-100000

.1.3.6.1.4.1.9.9.513.1.1.1.1.77

cLApEchoRequestCount

This object represents the echo request packet
count sent from AP to access controller.

cLApEchoResponseLossCount

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.78

This object represents the echo response loss
count from access controller to AP.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.79

cLApModuleInserted

This object represents the type of the module
inserted in to the AP.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.1.1.80

cLApEnableModule

This object specifies the status of the external
module .
A value of 'true' indicates module is enabled.
A value of 'false' indicates module is disabled.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.81

cLApIsUniversal

This object represents the if the AP is
universal AP.
A value of 'true' indicates AP is universal SKU based AP.
A value of 'false' indicates AP is non-Universal SKU AP.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.82

cLApUniversalPrimeStatus

This object represents the method of Priming
of the Universal AP.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.1.1.83

cLApIsMaster

This object represents whether the flex AP is a
master AP. This applies only to FlexExpress controllers.
A value of 'true' indicates AP is a master AP.
A value of 'false' indicates AP is not a master AP.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.84

cLApBleFWDownloadStatus

This object represents the list of APs in which BLE
firmware download is in progress.
A value of 'true' indicates BLE download is in progress.
A value of 'false' indicates BLE download is not in progress.

cLApDot11XorDartConnectorStatus

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.85

This object represents the XOR dart connector status.

cLApCtsSxpDefaultPassword

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.1.1.86

This object specifies the SXP(Security Group Tag Exchange
Protocol) default password.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.1.1.87

cLApCtsSxpState

This object specifies SXP(Security Group Tag Exchange
Protocol) state.
A value of 'true' indicates sxp state is enabled.
A value of 'false' indicates sxp state is disabled.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.88

cLApCtsSxpMode

This object specifies SXP(Security Group Tag Exchange
Protocol) mode.
A value of 'true' indicates sxp mode is enabled.
A value of 'false' indicates sxp mode is disabled.

cLApCtsSxpListenerMinHoldtime

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.89

This object specifies SXP(Security Group Tag Exchange
Protocol) listener hold time.
It specifies the global maximum hold-time for
SXP connections in 'listener' mode.

Value of this object must be lesser th…

cLApCtsSxpListenerMaxHoldtime

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.90

cLApCtsSxpReconcilePeriod

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.91

This object specifies SXP(Security Group Tag Exchange
Protocol) reconcile period.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.92

cLApCtsSxpRetryPeriod

This object specifies SXP(Security Group Tag Exchange
Protocol) retry period.

cLApCtsSxpSpeakerHoldTime

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.93

This object specifies SXP(Security Group Tag Exchange
Protocol) speaker hold time.

cLApCtsSxpSpeakerKeepAlive

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.94

This object specifies SXP(Security Group Tag Exchange
Protocol) speaker keep alive time.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.95

cLApCtsInlineTagStatus

This object specifies Cisco Trustsec inline tagging
is enabled/disabled.
A value 'true' indicates inline tag is enabled.
A value 'false' indicates inline tag is disabled.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.96

cLApCtsSgaclStatus

This object specifies Cisco Trustsec Security Group Tag
ACL enforcement status.
A value 'true' indicates SgACL enforcement is enabled
A value 'false' indicates SgACL enforcement is disabled

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.97

cLApCtsOverrideStatus

This object specifies Cisco Trustsec AP Override status.
A value of 'true' indicates CTS AP Override is enabled.
A value of 'false' indicates CTS AP Override is disabled.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.98

cLApModeClear

This object specifies to clear the modes like 'Sniffer',
'Monitor' which is not inherited from tag configuration on
controller. Once cleared, AP may reboot and move to the AP mode
based on current tag configuration.
A v…

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.103

cLApSiteTagName

This object specifies the site tag name of the AP

OctetString

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.1.1.1.104

cLApRfTagName

This object specifies the RF tag name of the AP

OctetString

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.1.1.1.105

cLApPolicyTagName

This object specifies the policy tag name of the AP.

OctetString

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.1.1.1.106

cLApTagSource

This object specifies the source of the tag.

Enumeration

Enumerated Values:

1	none
2	static
3	filterengine
4	pnpserver
5	default
6	location

.1.3.6.1.4.1.9.9.513.1.1.1.1.107

cLApUsbModuleName

This object specifies module name of USB module
On the AP.

OctetString

Constraints:
range: 0-66

.1.3.6.1.4.1.9.9.513.1.1.1.1.108

cLApUsbModuleState

This object specifies whether USB module detected or not
detected on the AP.

OctetString

Constraints:
range: 0-66

.1.3.6.1.4.1.9.9.513.1.1.1.1.109

cLApUsbModuleProductId

This object specifies product Id of USB module on the AP.

OctetString

Constraints:
range: 0-19

.1.3.6.1.4.1.9.9.513.1.1.1.1.110

cLApUsbDescription

This object specifies description of USB module on the AP.

OctetString

Constraints:
range: 0-66

.1.3.6.1.4.1.9.9.513.1.1.1.1.111

cLApUsbStateInfo

This object specifies State(enable/disable) of USB module
on the AP.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.112

cLApUsbOverride

This object specifies Override(enable/disable) of USB module
on the AP.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.113

cLApUsbSerialNumber

This object specifies serial number of USB module
on the AP.

OctetString

Constraints:
range: 0-12

.1.3.6.1.4.1.9.9.513.1.1.1.1.114

cLApUsbMaxPower

This object specifies max power given to USB module
on the AP.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.1.1.115

cLApLagConfigStatus

This object specifies the configured LAG status(enable/disable)
on the AP.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.116

cLApMonitorModeOptStatus

This object specifies the Monitor Mode optimization support(enable/disable)
on the AP.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.1.1.117

cLApFilterName

This object specifies the Filter name applied on this AP

OctetString

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.1.1.1.118

cLApIfSmtParamTable

table

.1.3.6.1.4.1.9.9.513.1.1.2 · 1 row entry · 1 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApIfSmtParamTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApIfSmtParamTable'

This table represents the station management
information in the APs that have joined the
controller.  Information populated through the
entries of this table is used by the AP to
perform the expected 802.11 operations on
the respective dot11 interfaces to coordinate with
other 802.11 devices in the network.
          
Since this table has the indices defined in the
tables cLApTable and cLApDot11IfTable, an entry in
this table is automatically removed when the
respective entry is removed in either of those
tables.

cLApIfSmtParamEntry row .1.3.6.1.4.1.9.9.513.1.1.2.1

An entry in this table represents the information
pertaining to one particular dot11 interface of
this AP used to perform the 802.11 protocol
operations on the respective dot11 interface.

Rows are added or …

Indexes

Column	Syntax	OID
cLApIfSmtDot11Bssid This object represents the base BSSID of this AP, which is the MAC address of the radio interface of this AP.	SNMPv2-TCMacAddress Type Constraints: `range: 6` Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	`.1.3.6.1.4.1.9.9.513.1.1.2.1.1`

cLApCountryTable

table

.1.3.6.1.4.1.9.9.513.1.1.3 · 1 row entry · 2 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApCountryTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApCountryTable'

This table represents the country settings for
the 802.11 LWAPP Access Points that have joined the
controller.
An entry is automatically added by the controller 
when a Access Point joins the controller. 
The entry is removed when Access Point disasscociates 
from the controller.

cLApCountryEntry row .1.3.6.1.4.1.9.9.513.1.1.3.1

Each entry in this table provides country setting
about one 802.11 LWAPP Access Point that has joined
the controller.
Entries are removed when the APs lose their
association with the controller due to loss
of communica…

Indexes

Column	Syntax	OID
cLApCountryCode This object specifies the country in which the AP is operating. This value is the 3 letter country code.	OctetStringr/w Constraints: `range: 1-255`	`.1.3.6.1.4.1.9.9.513.1.1.3.1.1`
cLApCountryAllowed This object represents the country in which the AP is operating. This value is a list of country codes sperated by comma.	OctetString Constraints: `range: 1-255`	`.1.3.6.1.4.1.9.9.513.1.1.3.1.2`

cLApCrashInfoTable

table

.1.3.6.1.4.1.9.9.513.1.1.8 · 1 row entry · 3 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApCrashInfoTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApCrashInfoTable'

This table represents the crash file information
for each AP. 
An entry is automatically added to this table when 
an Access Points crashes and reboots. 
Entry is removed from this table when AP 
disassociates from the controllers.

cLApCrashInfoEntry row .1.3.6.1.4.1.9.9.513.1.1.8.1

Each entry in this table provides crash
information available for each AP.

Indexes

Column	Syntax	OID
cLApCrashFileName This object represents the crash file name for a specific AP.	OctetString Constraints: `range: 1-28`	`.1.3.6.1.4.1.9.9.513.1.1.8.1.1`
cLApCrashFileSize This object represents the size of the crash file.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.1.8.1.2`
cLApCrashFileTimeStamp This object represents the timestamp of the crash file.	SNMPv2-TCDateAndTime Type Constraints: `range: 8` `range: 11` Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	`.1.3.6.1.4.1.9.9.513.1.1.8.1.3`

cLApSysInfoTable

table

.1.3.6.1.4.1.9.9.513.1.1.9 · 1 row entry · 5 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApSysInfoTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApSysInfoTable'

This table represents the system information
for each AP.

cLApSysInfoEntry row .1.3.6.1.4.1.9.9.513.1.1.9.1

Each entry in this table provides system
information for each AP.

Indexes

Column	Syntax	OID
cLApSysMemType This object represents the AP system memory type.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: `range: 0..255`	`.1.3.6.1.4.1.9.9.513.1.1.9.1.1`
cLApSysMemSize This object represents the total AP system memory size in Kbytes.	KBytesSNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.1.9.1.2`
cLApSysFlashSize This object represents the AP flash size in Kbytes.	KBytesSNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.1.9.1.3`
cLApSysCpuType This object represents the AP cpu type	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: `range: 0..255`	`.1.3.6.1.4.1.9.9.513.1.1.9.1.4`
cLApSysFlashType This object represents the AP Flash type.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: `range: 0..255`	`.1.3.6.1.4.1.9.9.513.1.1.9.1.5`

cLApExtTable

table

.1.3.6.1.4.1.9.9.513.1.1.10 · 1 row entry · 15 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApExtTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApExtTable'

This table represents the system information
for each AP.

cLApExtEntry row .1.3.6.1.4.1.9.9.513.1.1.10.1

Each entry in this table provides system
information for each AP.

Indexes

Column Syntax OID

cLApLEDFlashStatus

This object specifies the state of the AP LED Flash.
A value of 'true' indicates LED flash is enabled.
A value of 'false' indicates LED flash is disabled.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.10.1.1

cLApLEDFlashDuration

This object specifies the duration for which the AP's LED
should blink. This is applicable when the value of
cLApFlashStatus is TRUE. Value of 0 indicates the blinking
for infinite duration.

secondsSNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.1.10.1.2

cLApInetAddressType

This object specifies the type of the AP
address made available through
cLApInetAddress.

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.9.9.513.1.1.10.1.3

cLApInetAddress

This object specifies the address of the
Access Point.

cLApStaticIpv6AddressEnabled

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.10.1.4

This object specifies that AP is
configured to use static IPv6 address.
A value of 'true' indicates AP can assign with static
IP address.
A value of 'false' indicates AP cannot assign with static
IP address.

cLApStaticIpv6InetAddressType

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.10.1.5

This object specified the address type made
available through cLApStaticIpv6InetAddress.

cLApStaticIpv6InetAddress

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.9.9.513.1.1.10.1.6

This object specifies the static IPv6 address
of the Access Point.

cLApStaticIpv6PrefixLength

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.10.1.7

This object specifies the prefix length of the static IP
Address configured on the AP.

Unsigned32r/w

Constraints:
range: 0-128

.1.3.6.1.4.1.9.9.513.1.1.10.1.8

cLApStaticIpv6GatewayInetAddressType

This object specified the address type made
available through cLApStaticIpv6GatewayInetAddress.

cLApStaticIpv6GatewayInetAddress

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.9.9.513.1.1.10.1.9

This object specifies the IPv6 Address of the Gateway server.
This attribute can be configured only if the static IP
option is turned on in the AP.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.10.1.10

cLApStaticIpNetmaskType

This object specifies the netmask address type for AP's
static IP.

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.9.9.513.1.1.10.1.11

cLApStaticIpNetmask

This object specifies netmask for ipv4 address.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.10.1.12

cLApPreferMode

This object represents the capwap prefer-mode (ipv4 or ipv6)
of AP.

Enumeration

Enumerated Values:

1	ipv4
2	ipv6

.1.3.6.1.4.1.9.9.513.1.1.10.1.13

cLApPreferModeApplied

This object represents the prefer-mode of AP applied by
apgroup config or global config.
apgroup - capwap prefer mode applied at ap group level.
global - capwap prefer mode applied globally.

Enumeration

Enumerated Values:

1	apgroup
2	global

.1.3.6.1.4.1.9.9.513.1.1.10.1.14

cLApIndoorMode

This object specifies the indoor/outdoor mode of the AP.
A value of 'true' indicates AP is in Indoor Mode.
A value of 'false' indicates AP is in Outdoor Mode.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.10.1.17

cLApEnvInfoTable

table

.1.3.6.1.4.1.9.9.513.1.1.11 · 1 row entry · 4 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApEnvInfoTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApEnvInfoTable'

This table represents information about temperature
degree state and orientation of the AP

cLApEnvInfoEntry row .1.3.6.1.4.1.9.9.513.1.1.11.1

Each entry represents a conceptual row in this table.
An entry is created when AP joins the controller.
The entry is removed when the AP lose their
association with the controller due to loss of
communication with contr…

Indexes

Column Syntax OID

cLApEnvTemperatureDegree

This object represents temperature
of the AP in both celcius and fahrenheit.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.11.1.1

cLApEnvTemperatureState

This object represents temperature state
of the AP.

Enumeration

Enumerated Values:

0	unknown
1	green
2	yellow
3	red

.1.3.6.1.4.1.9.9.513.1.1.11.1.2

cLApEnvOrientation

This object represents orientation
of the AP.

Enumeration

Enumerated Values:

0	unknown
1	vertical
2	horizontal

.1.3.6.1.4.1.9.9.513.1.1.11.1.3

cLApEnvPoeOutStatus

This object represents POE out status
of the AP.

Enumeration

Enumerated Values:

1	unknown
2	on
3	off

.1.3.6.1.4.1.9.9.513.1.1.11.1.4

cLApGpsInfoTable

table

.1.3.6.1.4.1.9.9.513.1.1.12 · 1 row entry · 6 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApGpsInfoTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApGpsInfoTable'

This table represents information about location and
velocity parameters received from the GPS module on the
LWAPP Access Points that have joined the controller.

cLApGpsInfoEntry row .1.3.6.1.4.1.9.9.513.1.1.12.1

Indexes

Column Syntax OID

cLApGpsLocationPresent

This object represents whether the access point
has the GPS module installed or not.
A value of 'true' indicates GPS module is present in
AP.
A value of 'false' indicates GPS module is not
present in AP.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.12.1.1

cLApGpsLocationValid

This object represents whether the location
information is valid or not.
A value of 'true' indicates GPS location
is valid.
A value of 'false' indicates GPS location
is not valid.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.1.12.1.2

cLApGpsLatitude

This object represents latitude information
in the GPS data received.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.12.1.3

cLApGpsLongitude

This object represents longitude information
in the GPS data received.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.12.1.4

cLApGpsAltitude

This object represents altitude information
in the GPS data received.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.1.12.1.5

cLApGpsCollectionTime

This object represents the time when GPS
data was collected.

SNMPv2-TCTimeStamp

Based On: SNMPv2-SMITimeTicks

Description:

The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…

.1.3.6.1.4.1.9.9.513.1.1.12.1.6

cLApDot11IfTable

table

.1.3.6.1.4.1.9.9.513.1.2.1 · 1 row entry · 42 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApDot11IfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApDot11IfTable'

This table represents the information about the
basic functional parameters corresponding to
the dot11 interfaces of the APs that have joined
the controller.

cLApDot11IfEntry row .1.3.6.1.4.1.9.9.513.1.2.1.1

An entry in this table represents the 802.11
functional parameters of the dot11 interface of
an AP that has joined the controller.

Entries are added when the APs associate to this
controller and deleted whe…

Indexes

Column Syntax OID

cLApDot11IfSlotId

This object represents the slot ID of a dot11
interface on an AP.

The slot ID for a particular dot11 interface as
represented by this object ranges from 0 to
cLApMaxNumberOfDot11Slots - 1.

CISCO-LWAPP-TC-MIBCLApIfType

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.1.1.1

cLApDot11IfType

This object represents the type of this dot11
interface.

Type Values:

1	dot11bg
2	dot11a
3	uwb
4	dot11abgn
5	rlan
6	dot11_6ghz
7	dot11_xor_5_6ghz

.1.3.6.1.4.1.9.9.513.1.2.1.1.2

cLApDot11IfRegDomain

This object represents the regulatory domain for
this radio type on this AP.

OctetString

Constraints:
range: 1-255

.1.3.6.1.4.1.9.9.513.1.2.1.1.3

cLApDot11nSupport

This objects represents whether 11n support is enabled
on this radio.
A value of 'true' indicates 11n support is enabled.
A value of 'false' indicates 11n support is disabled.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.2.1.1.4

cLAp11nChannelBandwidth

This object specifies the channel bandwidth for
this AP. This applies to 802.11n networks only.
This has been deprecated for cLAp11ChannelBandwidth.

mhzEnumerationr/w

Enumerated Values:

1	five
2	ten
3	twenty
4	forty

.1.3.6.1.4.1.9.9.513.1.2.1.1.5

cLApLomEnableddeprecated

This object indicates whether this AP is being monitored
by the location server. A value of 'true' indicates that
the monitoring is enabled. A value of 'false' indicates
that the monitoring is disabled.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.2.1.1.6

cLApLomFirstChannel

This object specifies the first location channel that is
being monitored.

Type Constraints:
range: 1..14
range: 34
range: 36
range: 38
range: 40
range: 42
range: 44
range: 46
range: 48
range: 52
range: 56
range: 60
range: 64
range: 149
range: 153
range: 157
range: 161

.1.3.6.1.4.1.9.9.513.1.2.1.1.7

cLApLomSecondChannel

This object specifies the second location channel that
is being monitored.

.1.3.6.1.4.1.9.9.513.1.2.1.1.8

cLApLomThirdChannel

This object specifies the third location
channel that is being monitored.

.1.3.6.1.4.1.9.9.513.1.2.1.1.9

cLApLomFourthChannel

This object specifies the fourth location
channel that is being monitored.

CISCO-LWAPP-TC-MIBCLDot11Channel

.1.3.6.1.4.1.9.9.513.1.2.1.1.10

cLApExtensionChanneldeprecated

This object specifies the extension channel. This is
applicable when the channel bandwidth is set to 40mhz.

.1.3.6.1.4.1.9.9.513.1.2.1.1.11

cLApLegacyBeamForming

This object indicates the status of legacy beam forming
in this AP. This object is applicable only for
11n supported APs.
For APs that does not support legacy beam forming,
a get request on this attribute will return
t…

Enumerationr/w

Enumerated Values:

1	enable
2	disable
3	notApplicable

.1.3.6.1.4.1.9.9.513.1.2.1.1.12

cLApCdpOverAirEnabled

This object specifies the status of Cisco Discovery
Protocol(CDP) in this interface, represented by
cLApDot11IfSlotId of the AP, represented by
cLApSysMacAddress.
A value of 'true' indicates that CDP is enabled in
the d…

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.2.1.1.13

cLApDot11IfAdminStatus

This object specifies the AP's interface admin
status.
A value of 'true' indicates admin state is up.
A value of 'false' indicates admin state is down.

cLApDot11IfLinkChangeCount

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.2.1.1.14

This object represents the link change count of a dot11
interface on an AP.

cLApPromiscuousModeDwelling

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.1.1.15

cLApDot11MaxClients

This object specifies the max supported associated clients
of a dot11 interface on an AP.

Unsigned32r/w

Constraints:
range: 1-200

.1.3.6.1.4.1.9.9.513.1.2.1.1.16

This object represents the percentage of time for the dot11
interface of an Access Point spent in promiscuous mode
dwelling.

percentageSNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.1.1.17

cLApDot11IfStaKeepingTime

This object represents the time in hundredths
of a second since the last dot11 interface state changed.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.1.1.18

cLApDot11IfLinkSpeed

This object represents the speed of the interface
in units of 1,000,000 bits per second.

bpsSNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.1.1.19

cLApDot11IfMtu

This object represents interface's MTU value.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.1.1.20

cLApDot11IfDesc

This object represents the description of this interface.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.2.1.1.21

cLApDot11acSupport

This objects represents whether 802.11ac support is
enabled on this AP.
A value of 'true' indicates 11ac support for slot is
enabled.
A value of 'false' indicates 11ac support for slot is
disabled.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.2.1.1.22

cLAp11ChannelBandwidth

This object specifies the channel bandwidth for
this AP. This applies to 802.11n and 802.11ac networks only.

mhzEnumerationr/w

Enumerated Values:

1	five
2	ten
3	twenty
4	fourty
5	eighty
6	onesixty
7	eightyeighty

.1.3.6.1.4.1.9.9.513.1.2.1.1.23

cLApExtensionChannels

This object represents the extension channels separated by
commas. This is applicable when the channel bandwidth is set
to 40mhz or 80mhz.

cLAPDot11IfMinTxPowerStep

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.2.1.1.24

This object represents minimum adjust step of the AP radio TX
power. The power step is coded as an unsigned integer in units
of dbm.

dbmSNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.1.1.25

cLApDot11XorRadioMode

This object specifies the radio mode for
the AP which has XOR radio.
servingClients - xor radio is configured to
serve the clients (local/flexconnect/bridge).
monitor -xor radio is configured to opera…

Enumerationr/w

Enumerated Values:

1	servingClients
2	monitor
3	sensor

.1.3.6.1.4.1.9.9.513.1.2.1.1.26

cLApDot11XorRadioBand

This object specifies the operating band of
the dot11 interface of an AP.
radioband24G - operating band for xor radio is 2.4GHz.
radioband5G - operating band for xor radio is 5GHz.
radioband6G - operating band for xor…

Enumerationr/w

Enumerated Values:

1	radioband24G
2	radioband5G
3	radioband6G

.1.3.6.1.4.1.9.9.513.1.2.1.1.27

cLApDot11XorRadioRoleAssignment

This object specifies the radio role assignment of
XOR radio.
auto - xor radio configured to change band/mode automatically.
manual - xor radio's band/mode can be configured manually.

Enumerationr/w

Enumerated Values:

1	auto
2	manual

.1.3.6.1.4.1.9.9.513.1.2.1.1.28

cLApDot11IfMaxDataRate

This object represents the maximum data rate of a dot11
interface on an AP in Mbps.

cLApDot11IfSensorReachability

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.1.1.29

This object represents sensor radio's ability to cover
localized RF neighbors.It represents value in percentage
which shows percentage of neighbors covered by this sensor.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.1.1.30

cLApDot11axSupport

This objects represents whether 802.11ax support is
enabled on this AP.
A value of 'true' indicates 11ax support for slot is
enabled.
A value of 'false' indicates 11ax support for slot is
disabled.

cLApFraCoverageOverlapFactor

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.2.1.1.31

This object represents the COF(Coverage Overlap Factor) in
percentage.COF represents overlap on a given radio's transmit
cell size by its adjacent neighbors.When COF value is higher
than FRA(Flexible Radio Assignment) s…

percentageSNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.9.9.513.1.2.1.1.32

cLApFraSuggestedMode

This object represents the band/mode XOR radio can move to,
for better performance.
static - XOR radio's band/mode is in manual assignment.
none - FRA(Flexible Radio Assignment) algorithm is disabled.
radioBand5GMonitor…

Enumeration

Enumerated Values:

1	static
2	none
3	radioBand5GMonitor
4	radioBand24G
5	notApplicable

.1.3.6.1.4.1.9.9.513.1.2.1.1.33

cLApDot11IfDualRadioModedeprecated

This object represents dual radio mode status of radio
enabled - Dual radio mode is enabled.
disabled- Dual radio mode is disabled.
None - Radio is not dual radio mode capable.

Enumerationr/w

Enumerated Values:

1	none
2	enabled
3	disabled

.1.3.6.1.4.1.9.9.513.1.2.1.1.34

cLApDot11IfDualRadioCapabledeprecated

This object represents whether radio is dual radio capable or
not

Enumeration

Enumerated Values:

0	notcapable
1	dualmodecapable

.1.3.6.1.4.1.9.9.513.1.2.1.1.35

cLApDot11IfRadioFRACapabledeprecated

This object represents whether radio is FRA capable or not.

Enumeration

Enumerated Values:

0	notcapable
1	capable

.1.3.6.1.4.1.9.9.513.1.2.1.1.36

cLApDot11IfPhyS80EightyChannelNumber

Secondary 80MHz channel number of the AP Interface.
Allowed channel numbers also depends on the current
Country Code set in the Switch.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.9.9.513.1.2.1.1.37

cLApDot11IfDualRadioOperationdeprecated

This object represents dual radio mode operation of
the slot.
auto - Dual radio mode is automatic.
manual - Dual radio mode is configurable manually.
none - Radio is not dual radio mode capable.

Enumerationr/w

Enumerated Values:

1	none
2	auto
3	manual

.1.3.6.1.4.1.9.9.513.1.2.1.1.39

cLApDot11IfRadioRoleOperationdeprecated

This object represents the radio role operation
of the slot.
auto - Radio role assignment is automatic.
manual - Radio role assignment is manual.

Enumerationr/w

Enumerated Values:

1	none
2	auto
3	manual

.1.3.6.1.4.1.9.9.513.1.2.1.1.40

cLApDot11IfRadioRoledeprecated

This object represents the role for the slot.
local - The means the slot is capable of serving clients.
monitor - The slot does not serves client, only monitors.

Enumerationr/w

Enumerated Values:

1	none
2	local
3	monitor

.1.3.6.1.4.1.9.9.513.1.2.1.1.41

cLApDot11IfRptncPresent

This object represents whether Self Identifying Antenna RP-TNC is
present for the radio.
A value of 'true' indicates SIA RP-TNC is present.
A value of 'false' indicates SIA RP-TNC is not present.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.2.1.1.42

cLApDot11IfDartPresent

This object represents whether Self Identifying Antenna DART is
present for the radio
A value of 'true' indicates SIA DART is present.
A value of 'false' indicates SIA DART is not present.

cLApSysMacAddress cLApEthernetIfSlotId

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.2.1.1.43

cLApEthernetIfTable

table

.1.3.6.1.4.1.9.9.513.1.2.2 · 1 row entry · 36 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApEthernetIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApEthernetIfTable'

This table represents the information about the
basic functional parameters corresponding to
the Ethernet interfaces of the APs that have joined
the controller.

cLApEthernetIfEntry row .1.3.6.1.4.1.9.9.513.1.2.2.1

An entry in this table represents the functional
parameters of the Ethernet interface of an AP that
has joined the controller.

Entries are added when the APs associate to this
controller and deleted when th…

Indexes

Column Syntax OID

cLApEthernetIfSlotId

This object represents the slot ID of an Ethernet
interface on an AP.

The slot ID for a particular Ethernet interface as
represented by this object ranges from 0 to
cLApMaxNumberOfEthernetSlots - 1.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.1

cLApEthernetIfName

This object represents the name of the
ethernet interface.

OctetString

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.2.2.1.2

cLApEthernetIfMacAddress

This object represents MAC address of the ethernet
interface in the slot represented by
cLApEthernetIfSlotId.

cLApEthernetIfAdminStatus

Type Constraints:
range: 6

Description:

.1.3.6.1.4.1.9.9.513.1.2.2.1.3

This object specifies the admin state of the physical
ethernet interface on the AP.
up - Admin state of ethernet interface is up.
down - Admin state of ethernet interface is down.

Enumerationr/w

Enumerated Values:

1	up
2	down

.1.3.6.1.4.1.9.9.513.1.2.2.1.4

cLApEthernetIfOperStatus

This object represents the operational state
of the physical Ethernet interface on the AP.
up - Operational state of ethernet interface is up.
down - Operational state of ethernet interface is down.

Enumeration

Enumerated Values:

1	up
2	down

.1.3.6.1.4.1.9.9.513.1.2.2.1.5

cLApEthernetIfRxUcastPkts

This object represents the total number of unicast packets
received on the interface.

cLApEthernetIfRxNUcastPkts

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.6

This object represents the total number of non-unicast or
multicast packets received on the interface

cLApEthernetIfTxUcastPkts

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.7

This object represents the total number of unicast packets
transmitted on the interface.

cLApEthernetIfTxNUcastPkts

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.8

This object represents the total number of non-unicast or
multicast packets transmitted on the interface

cLApEthernetIfRxTotalBytes

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.9

cLApEthernetIfDuplex

This object represents the interface's duplex mode

Enumeration

Enumerated Values:

1	unknown
2	halfduplex
3	fullduplex
4	auto

.1.3.6.1.4.1.9.9.513.1.2.2.1.10

cLApEthernetIfLinkSpeed

This object represents the speed of the interface in units of
1,000,000 bits per second

SNMPv2-SMIGauge32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.11

cLApEthernetIfPOEPower

This object represents whether this interface supports
Power Over Ethernet (POE)
none - POE is not supported
drawn - This interface supports POE, and power is
being drawn
notdrawn - POE power is not dr…

Enumeration

Enumerated Values:

1	none
2	drawn
3	notdrawn

.1.3.6.1.4.1.9.9.513.1.2.2.1.12

This object represents the total number of bytes in the
error-free packets received on the interface.

BytesSNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.13

cLApEthernetIfTxTotalBytes

This object represents the total number of bytes in the
error-free packets transmitted on the interface.

BytesSNMPv2-SMICounter32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.14

cLApEthernetIfInputCrc

This object represents the total number of CRC error in
packets received on the interface.

cLApEthernetIfInputAborts

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.15

This object represents the total number of packet aborted
while receiving on the interface.

cLApEthernetIfInputErrors

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.16

This object represents the sum of all errors in the packets
while receiving on the interface.

cLApEthernetIfInputFrames

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.17

This object represents the total number of packet received
incorrectly having a CRC error and a noninteger number
of octets on the interface.

cLApEthernetIfInputOverrun

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.18

This object represents the number of times the receiver
hardware was incapable of handing received data to a
hardware buffer because the input rate exceeded the
receiver's capability to handle the data.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.19

cLApEthernetIfInputDrops

This object represents the total number of packets dropped
while receiving on the interface because the queue
was full.

cLApEthernetIfInputResource

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.20

This object represents the total number of resource errors in
packets received on the interface.

cLApEthernetIfUnknownProtocol

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.21

This object represents the total number of packet discarded on
the interface due to unknown protocol.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.22

cLApEthernetIfRunts

This object represents the number of packets that
are discarded because they are smaller than the
medium's minimum packet size.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.23

cLApEthernetIfGiants

This object represents the number of packets that
are discarded because they exceed the medium's
maximum packet size.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.24

cLApEthernetIfThrottle

This object represents the total number of times the
interface advised a sending NIC that it was
overwhelmed by packets being sent and to slow the
pace of delivery.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.25

cLApEthernetIfResets

This object represents number of times that an
interface has been completely reset.

cLApEthernetIfOutputCollision

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.26

This object represents the total number of packet
retransmitted due to an Ethernet collision.

cLApEthernetIfOutputNoBuffer

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.27

This object represents the total number of packets discarded
because there was no buffer space.

cLApEthernetIfOutputResource

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.28

This object represents the total number of resource
errors in packets transmitted on the interface.

cLApEthernetIfOutputUnderrun

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.29

This object represents the number of times the transmitter
has been running faster than the router can handle.

cLApEthernetIfOutputErrors

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.30

This object represents sum of all errors that prevented
the final transmission of packets out of the interface.

cLApEthernetIfOutputTotalDrops

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.31

This object represents the total number of packets dropped
while transmitting from the interface because the queue
was full.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.32

cLApEthernetIfCdpEnabled

This object specifies the status of Cisco Discovery
Protocol(CDP) in this interface represented by
cLApEthernetIfSlotId of the AP represented by
cLApSysMacAddress.
A value of 'true' indicates that CDP is enabled in
this…

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.2.2.1.33

cLApEthernetIfMtu

This object represents interface's MTU value

cLApEthernetIfLinkChangeCount

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.34

cLApEthernetIfType

This object represents the type of interface. Additional
values for ifType are assigned by the Internet Assigned Numbers
Authority (IANA), through updating the syntax of the
IANAifType textual convention.

IANAifType-MIBIANAifType

Type Values:

1	other
2	regular1822
3	hdh1822
4	ddnX25
5	rfc877x25
6	ethernetCsmacd
7	iso88023Csmacd
8	iso88024TokenBus
9	iso88025TokenRing
10	iso88026Man
11	starLan
12	proteon10Mbit
13	proteon80Mbit
14	hyperchannel
15	fddi
16	lapb
17	sdlc
18	ds1
19	e1
20	basicISDN
21	primaryISDN
22	propPointToPointSerial
23	ppp
24	softwareLoopback
25	eon
26	ethernet3Mbit
27	nsip
28	slip
29	ultra
30	ds3
31	sip
32	frameRelay
33	rs232
34	para
35	arcnet
36	arcnetPlus
37	atm
38	miox25
39	sonet
40	x25ple
41	iso88022llc
42	localTalk
43	smdsDxi
44	frameRelayService
45	v35
46	hssi
47	hippi
48	modem
49	aal5
50	sonetPath
51	sonetVT
52	smdsIcip
53	propVirtual
54	propMultiplexor
55	ieee80212
56	fibreChannel
57	hippiInterface
58	frameRelayInterconnect
59	aflane8023
60	aflane8025
61	cctEmul
62	fastEther
63	isdn
64	v11
65	v36
66	g703at64k
67	g703at2mb
68	qllc
69	fastEtherFX
70	channel
71	ieee80211
72	ibm370parChan
73	escon
74	dlsw
75	isdns
76	isdnu
77	lapd
78	ipSwitch
79	rsrb
80	atmLogical
81	ds0
82	ds0Bundle
83	bsc
84	async
85	cnr
86	iso88025Dtr
87	eplrs
88	arap
89	propCnls
90	hostPad
91	termPad
92	frameRelayMPI
93	x213
94	adsl
95	radsl
96	sdsl
97	vdsl
98	iso88025CRFPInt
99	myrinet
100	voiceEM
101	voiceFXO
102	voiceFXS
103	voiceEncap
104	voiceOverIp
105	atmDxi
106	atmFuni
107	atmIma
108	pppMultilinkBundle
109	ipOverCdlc
110	ipOverClaw
111	stackToStack
112	virtualIpAddress
113	mpc
114	ipOverAtm
115	iso88025Fiber
116	tdlc
117	gigabitEthernet
118	hdlc
119	lapf
120	v37
121	x25mlp
122	x25huntGroup
123	transpHdlc
124	interleave
125	fast
126	ip
127	docsCableMaclayer
128	docsCableDownstream
129	docsCableUpstream
130	a12MppSwitch
131	tunnel
132	coffee
133	ces
134	atmSubInterface
135	l2vlan
136	l3ipvlan
137	l3ipxvlan
138	digitalPowerline
139	mediaMailOverIp
140	dtm
141	dcn
142	ipForward
143	msdsl
144	ieee1394
145	if-gsn
146	dvbRccMacLayer
147	dvbRccDownstream
148	dvbRccUpstream
149	atmVirtual
150	mplsTunnel
151	srp
152	voiceOverAtm
153	voiceOverFrameRelay
154	idsl
155	compositeLink
156	ss7SigLink
157	propWirelessP2P
158	frForward
159	rfc1483
160	usb
161	ieee8023adLag
162	bgppolicyaccounting
163	frf16MfrBundle
164	h323Gatekeeper
165	h323Proxy
166	mpls
167	mfSigLink
168	hdsl2
169	shdsl
170	ds1FDL
171	pos
172	dvbAsiIn
173	dvbAsiOut
174	plc
175	nfas
176	tr008
177	gr303RDT
178	gr303IDT
179	isup
180	propDocsWirelessMaclayer
181	propDocsWirelessDownstream
182	propDocsWirelessUpstream
183	hiperlan2
184	propBWAp2Mp
185	sonetOverheadChannel
186	digitalWrapperOverheadChannel
187	aal2
188	radioMAC
189	atmRadio
190	imt
191	mvl
192	reachDSL
193	frDlciEndPt
194	atmVciEndPt
195	opticalChannel
196	opticalTransport
197	propAtm
198	voiceOverCable
199	infiniband
200	teLink
201	q2931
202	virtualTg
203	sipTg
204	sipSig
205	docsCableUpstreamChannel
206	econet
207	pon155
208	pon622
209	bridge
210	linegroup
211	voiceEMFGD
212	voiceFGDEANA
213	voiceDID
214	mpegTransport
215	sixToFour
216	gtp
217	pdnEtherLoop1
218	pdnEtherLoop2
219	opticalChannelGroup
220	homepna
221	gfp
222	ciscoISLvlan
223	actelisMetaLOOP
224	fcipLink
225	rpr
226	qam
227	lmp
228	cblVectaStar
229	docsCableMCmtsDownstream
230	adsl2
231	macSecControlledIF
232	macSecUncontrolledIF
233	aviciOpticalEther
234	atmbond
235	voiceFGDOS
236	mocaVersion1
237	ieee80216WMAN
238	adsl2plus
239	dvbRcsMacLayer
240	dvbTdm
241	dvbRcsTdma
242	x86Laps
243	wwanPP
244	wwanPP2
245	voiceEBS
246	ifPwType
247	ilan
248	pip
249	aluELP
250	gpon
251	vdsl2
252	capwapDot11Profile
253	capwapDot11Bss
254	capwapWtpVirtualRadio
255	bits
256	docsCableUpstreamRfPort
257	cableDownstreamRfPort
258	vmwareVirtualNic
259	ieee802154
260	otnOdu
261	otnOtu
262	ifVfiType
263	g9981
264	g9982
265	g9983
266	aluEpon
267	aluEponOnu
268	aluEponPhysicalUni
269	aluEponLogicalLink
270	aluGponOnu
271	aluGponPhysicalUni
272	vmwareNicTeam
277	docsOfdmDownstream
278	docsOfdmaUpstream
279	gfast
280	sdci
281	xboxWireless
282	fastdsl
283	docsCableScte55d1FwdOob
284	docsCableScte55d1RetOob
285	docsCableScte55d2DsOob
286	docsCableScte55d2UsOob
287	docsCableNdf
288	docsCableNdr
289	ptm
290	ghn
291	otnOtsi
292	otnOtuc
293	otnOduc
294	otnOtsig
295	microwaveCarrierTermination
296	microwaveRadioLinkTerminal
297	ieee8021axDrni
298	ax25
299	ieee19061nanocom
300	cpri
301	omni
302	roe
303	p2pOverLan

.1.3.6.1.4.1.9.9.513.1.2.2.1.35

This object represents the link change count of
ethernet interface on the AP.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.2.1.36

cLApDot11RadioTable

table

.1.3.6.1.4.1.9.9.513.1.2.3 · 1 row entry · 7 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApDot11RadioTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApDot11RadioTable'

This table represents the information about the
basic functional parameters of the radios of the 
APs that have joined the controller.

cLApDot11RadioEntry row .1.3.6.1.4.1.9.9.513.1.2.3.1

An entry in this table represents the 802.11
functional parameters of the radio of
an AP that has joined the controller.

Entries are added when the APs associate to this
controller and deleted when they los…

Indexes

Column Syntax OID

cLApDot11RadioMACAddress

This object represents the base Mac address of
the radio.

CISCO-LWAPP-TC-MIBCLApDot11RadioSubband

Type Constraints:
range: 6

Description:

.1.3.6.1.4.1.9.9.513.1.2.3.1.1

cLApDot11RadioSubBand

This object reprsents the sub band on which
this radio operates.

Type Values:

1	all
2	sub49
3	sub52
4	sub54
5	sub58

.1.3.6.1.4.1.9.9.513.1.2.3.1.2

cLApDot11RadioVersion

This object represents the firmware version
of the radio.

OctetString

Constraints:
range: 1-50

.1.3.6.1.4.1.9.9.513.1.2.3.1.3

cLApDot11IsBackhaul

This object represents whether this interface
is backhaul radio or not.
A value of 'true' indicates backhaul access for radio is
enabled. A value of 'false' indicates backhaul access for
radio is disabled.

CISCO-LWAPP-TC-MIBCLApDot11RadioRole

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.2.3.1.4

cLApDot11RadioRole

This object represents the role of the radio.

Type Values:

0	shutdown
1	upDownlink
2	uplink
3	downlink
4	access
5	uplinkAccess
6	downlinkAccess
7	upDownlinkAccess
8	unknown

.1.3.6.1.4.1.9.9.513.1.2.3.1.5

cLApDot11RadioMode

This object represents the mode of the radio.
local(1) : The default option. Serving WLAN
clients and scanning channels for threats.
monitor(2) : A monitor mode. AP spends all of its…

Enumeration

Enumerated Values:

1	local
2	monitor
3	remote
4	rogueDetector
5	sniffer
6	bridge
7	seConnect
8	remoteBridge
9	hybridRemote
10	sensor

.1.3.6.1.4.1.9.9.513.1.2.3.1.6

cLApDot11RadioSubType

This object represents the subtype of the radio.
main(1) :radio operates normally.
rxOnly(2) :NOS radio type,which is explicitely used
for monitor mode operation.
slaveAc(3) :x-ale radio type is …

Enumeration

Enumerated Values:

1	main
2	rxOnly
3	slaveAc
4	remoteLan
5	xorTxRx
6	bleTxRx
7	bleRxOnly
8	slave

.1.3.6.1.4.1.9.9.513.1.2.3.1.7

cLApDot11IfAntennaTable

table

.1.3.6.1.4.1.9.9.513.1.2.4 · 1 row entry · 4 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApDot11IfAntennaTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApDot11IfAntennaTable'

This table represents the information about the
basic functional parameters corresponding to
the antenna on dot11 interfaces of the APs that have 
joined the controller.

cLApDot11IfAntennaEntry row .1.3.6.1.4.1.9.9.513.1.2.4.1

Indexes

cLApSysMacAddress cLApDot11IfSlotId cLApDot11IfAntennaId

Column Syntax OID

cLApDot11IfAntennaId

This object represents the antenna ID of a dot11
interface on an AP.
The antenna Id for a particular dot11 interface on
a slot as represented by this object.

Unsigned32

Constraints:
range: 1-8

.1.3.6.1.4.1.9.9.513.1.2.4.1.1

cLApDot11IfAntennaTxEnable

This object specifies whether this antenna is allowed
to trasmit or not.
A value of 'true' enables the antenna to transmit.
A value of 'false' disables the antenna to transmit.
This object has been deprecated for cLApDo…

cLApDot11IfAntennaRxEnable

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.2.4.1.2

This object specifies whether this antenna is allowed
to recieve or not.
A value of 'true' enables the antenna to receive.
A value of 'false' disables the antenna to receive.
cLApDot11IfAntennaRxEnable object is superse…

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.2.4.1.3

cLApDot11IfAntennaEnable

This object specifies whether this antenna is enabled
or not.
A value of 'true' indicates antenna is enabled.
A value of 'false' indicates antenna is disabled.

cLApSysMacAddress cLApVlanIfEthernetId

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.2.4.1.4

cLApVlanIfTable

table

.1.3.6.1.4.1.9.9.513.1.2.5 · 1 row entry · 4 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApVlanIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApVlanIfTable'

This table represents the information about the
basic functional parameters corresponding to
the ethernet interfaces of the APs that have
joined the controller.

cLApVlanIfEntry row .1.3.6.1.4.1.9.9.513.1.2.5.1

An entry in this table represents the VLAN
functional parameters of the Ethernet interface of
an AP that has joined the controller.
Entries are added when the administrator creates
an entry in this table.

Indexes

Column Syntax OID

cLApVlanIfEthernetId

This object represents the ID of a ethernet
interface on an AP.

Unsigned32

Constraints:
range: 0-3

.1.3.6.1.4.1.9.9.513.1.2.5.1.1

cLApVlanIfMode

This object specifies the AP's ethernet interface is
configured for.
normal - VLAN is not operating in access or trunk.
access - VLAN is operating in access mode
trunk - VLAN is operating in trunk mode.

Enumerationr/w

Enumerated Values:

1	normal
2	access
3	trunk

.1.3.6.1.4.1.9.9.513.1.2.5.1.2

cLApVlanIfEnable

This object specifies whether this interface is
enabled or not.
A value of 'true' enables the interface.
A value of 'false' disables the interface.. This will
delete all entries on this AP's ethernet interface.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.2.5.1.3

cLApVlanIfNativeVlanId

This object specifies the native VLAN ID
assigned to this AP's ethernet interface.
This only applies when the icLApVlanIfMode
is set to 'trunk'. For all other modes this
return a value of zero.

cLApSysMacAddress cLApVlanIfEthernetId cLApVlanListVlanId

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.5.1.4

cLApVlanListTable

table

.1.3.6.1.4.1.9.9.513.1.2.6 · 1 row entry · 2 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApVlanListTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApVlanListTable'

This table represents the information about the
basic functional parameters corresponding to
the VLAN Ethernet interfaces of the APs that have 
joined the controller.

cLApVlanListEntry row .1.3.6.1.4.1.9.9.513.1.2.6.1

Indexes

Column Syntax OID

cLApVlanListVlanId

This object represents the ID assigned to the
VLAN on this AP's ethernet interface.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.2.6.1.1

cLApVlanListRowStatus

This object specifies to add or delete an entry in this
table.

cLApNwTxPowerThresholdVer2

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …

.1.3.6.1.4.1.9.9.513.1.2.6.1.2

cLApDot11GlobalConfigTable

table

.1.3.6.1.4.1.9.9.513.1.2.7 · 1 row entry · 3 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApDot11GlobalConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApDot11GlobalConfigTable'

This table represents the information about the
global attributes of the radio interface, that would be
applicable for all the APs that join the controller.

cLApDot11GlobalConfigEntry row .1.3.6.1.4.1.9.9.513.1.2.7.1

An entry in this table represents the network
level configurations of the radio interface.
Entries cannot be added or deleted in this table.

Indexes

cLApDot11IfType

Column Syntax OID

cLApNwLegacyBeamFormingdeprecated

Enumerationr/w

Enumerated Values:

1	enable
2	disable
3	notApplicable

.1.3.6.1.4.1.9.9.513.1.2.7.1.1

cLApNwTxPowerThreshold

This object specifies the Global AP Transmit Power
Threshold value. The permissible range is -80 dbm to -50 dbm

dbmInteger32r/w

Constraints:
range: -80--50

.1.3.6.1.4.1.9.9.513.1.2.7.1.2

This object specifies the Global AP Transmit Power
Threshold value when Inteference Optimal mode of
Tx Power Control (TPC v2) is enabled. The permissible
range is -80 dbm to -50 dbm

dbmInteger32r/w

Constraints:
range: -80--50

.1.3.6.1.4.1.9.9.513.1.2.7.1.3

cLApDot11RadioStatsTable

table

.1.3.6.1.4.1.9.9.513.1.2.8 · 1 row entry · 13 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApDot11RadioStatsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApDot11RadioStatsTable'

This table represents the statistics information
about the radios of the APs that have joined the
controller.

cLApDot11RadioStatsEntry row .1.3.6.1.4.1.9.9.513.1.2.8.1

An entry in this table represents a statistics of
the radio of an AP that has joined the conttroller.

Entries are added when the APs associate to this
controller and deleted when they lose their
associati…

Indexes

cLApSysMacAddress cLApDot11IfType

Column	Syntax	OID
cLApDot11RadioStatsRxErrorFrameCount This object represents the number of error frames received on the radio.	framesSNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.2.8.1.1`
cLApDot11RadioStatsMacMicErrFrameCount This object represents the number of frames with wrong MIC received by AP on the radio.	framesSNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.2.8.1.2`
cLApDot11RadioStatsMacDecryptErrFrameCount This object represents the number of frames with destroyed encrypted data received by AP on the radio.	framesSNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.2.8.1.3`
cLApDot11RadioStatsRxMgmtFrameCount This object represents the total number of management frame received on the radio.	framesSNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.2.8.1.4`
cLApDot11RadioStatsRxCtrlFrameCount This object represents the total number of control frame received on the radio.	framesSNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.2.8.1.5`
cLApDot11RadioStatsRxDataFrameCount This object represents the total number of data frame received on the radio.	framesSNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.2.8.1.6`
cLApDot11RadioStatsTxMgmtFrameCount This object represents the total number of management frame transmitted on the radio.	framesSNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.2.8.1.7`
cLApDot11RadioStatsTxCtrlFrameCount This object represents the total number of control frame transmitted on the radio.	framesSNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.2.8.1.8`
cLApDot11RadioStatsTxDataFrameCount This object represents the total number of data frame transmitted on the radio.	framesSNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.2.8.1.9`
cLApDot11RadioStatsRxDataPacketCount This object represents the total number of data packets received on the radio.	packetsSNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.2.8.1.10`
cLApDot11RadioStatsTxDataPacketCount This object represents the total number of data packets transmitted on the radio.	packetsSNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.2.8.1.11`
cLApDot11RadioStatsRetryFrameCount This object represents the total number of downstream retry frames on the radio.	framesSNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.2.8.1.12`
cLApDot11RadioStatsRetryPacketCount This object represents the total number of downstream retry packets on the radio.	packetsSNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.2.8.1.13`

cLApDot11RadioRssiTable

table

.1.3.6.1.4.1.9.9.513.1.2.9 · 1 row entry · 3 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApDot11RadioRssiTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApDot11RadioRssiTable'

This table represents Per AP, Per Radio Stats information
of Average, Highest, Lowest Rssi of all the clients update
of the APs Radio.

cLApDot11RadioRssiEntry row .1.3.6.1.4.1.9.9.513.1.2.9.1

This entry contains stats information of
Average, Highest and Lowest RSSI of Per AP Per Radio.

Indexes

Column	Syntax	OID
cLApDot11RadioRssiHighest This object represents the Highest Rssi value of the specific radio on this access point. The value '0' dbm represents no activity on this access point radio.	dbmSNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.9.9.513.1.2.9.1.1`
cLApDot11RadioRssiLowest This object represents the Lowest Rssi value of the specific radio on this access point. The value '0' dbm represents no activity on this access point radio.	dbmSNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.9.9.513.1.2.9.1.2`
cLApDot11RadioRssiAverage This object represents the Average Rssi value of the specific radio on this access point. The value '0' dbm represents no activity on this access point radio.	dbmSNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.9.9.513.1.2.9.1.3`

cLApDot11RadioRateStatsTable

table

.1.3.6.1.4.1.9.9.513.1.2.10 · 1 row entry · 6 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApDot11RadioRateStatsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApDot11RadioRateStatsTable'

This table represents per AP, per radio, per rate stats
information of all the clients of the APs Radio.

cLApDot11RadioRateStatsEntry row .1.3.6.1.4.1.9.9.513.1.2.10.1

This entry contains stats information of Rx/Tx packets and
bytes of per AP per radio per rate.

Indexes

cLApSysMacAddress cLApDot11IfSlotId cLApDot11RadioRate

Column	Syntax	OID
cLApDot11RadioRate This object uniquely identifies the data rate value for a particular band.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.2.10.1.1`
cLApDot11RadioRateStatsRxPackets This object represents the number of packets received for the specific radio and data rate on this access point.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.2.10.1.2`
cLApDot11RadioRateStatsRxBytes This object represents the number of bytes received for the specific radio and data rate on this access point.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.2.10.1.3`
cLApDot11RadioRateStatsTxPackets This object represents the number of packets transmitted from the specific radio and data rate on this access point.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.2.10.1.4`
cLApDot11RadioRateStatsTxBytes This object represents the number of bytes transmitted from the specific radio and data rate on this access point.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.2.10.1.5`
cLApDot11RadioRateString This object represents the data rate in a user-friendly text string format.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: `range: 0..255`	`.1.3.6.1.4.1.9.9.513.1.2.10.1.6`

cLApDot11RadioSsidTable

table

.1.3.6.1.4.1.9.9.513.1.2.11 · 1 row entry · 2 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApDot11RadioSsidTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApDot11RadioSsidTable'

This table represents Per AP, Per Radio information
of Ssid of all the neighbor APs updating
the APs Radio.

cLApDot11RadioSsidEntry row .1.3.6.1.4.1.9.9.513.1.2.11.1

This entry contains ssid information of
Neighbor APs of Per AP Per Radio.

Indexes

cLApSysMacAddress cLApDot11IfType cLApSsidIndex

Column	Syntax	OID
cLApSsidIndex This object indicates the index of the ssid detected by Per AP Per Radio.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.2.11.1.1`
cLApDot11RadioSsidName This object represents the ssid name of the neighbor AP on this access point.	OctetString Constraints: `range: 1-32`	`.1.3.6.1.4.1.9.9.513.1.2.11.1.2`

cLApCableModemIfStatsTable

table

.1.3.6.1.4.1.9.9.513.1.2.12 · 1 row entry · 10 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApCableModemIfStatsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApCableModemIfStatsTable'

This table represents the statistics of cable
modem interface per AP when the CM connected to the AP.

cLApCableModemIfStatsEntry row .1.3.6.1.4.1.9.9.513.1.2.12.1

This entry contains stats information of cable modem
per AP

Indexes

Column	Syntax	OID
cLApCmMacAddress This object represents the MAC address of the Cable Modem that has been connected to the AP.	SNMPv2-TCMacAddress Type Constraints: `range: 6` Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	`.1.3.6.1.4.1.9.9.513.1.2.12.1.1`
cLApCmApMacAddress This object represents the ethernet MAC address of the AP where the Cable Modem is connected.	SNMPv2-TCMacAddress Type Constraints: `range: 6` Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	`.1.3.6.1.4.1.9.9.513.1.2.12.1.2`
cLApCmSwVersion This object represents the software version of the Cable Modem that has been connected to the AP.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: `range: 0..255`	`.1.3.6.1.4.1.9.9.513.1.2.12.1.3`
cLApEthernetSpeed This object represents the ethernet speed of the Cable Modem that has been connected to the AP.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: `range: 0..255`	`.1.3.6.1.4.1.9.9.513.1.2.12.1.4`
cLApEthernetStatus This object represents the ethernet status of the Cable Modem that has been connected to the AP.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: `range: 0..255`	`.1.3.6.1.4.1.9.9.513.1.2.12.1.5`
cLApCmStatus This object represents the status of the Cable Modem that has been connected to the AP.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: `range: 0..255`	`.1.3.6.1.4.1.9.9.513.1.2.12.1.6`
cLApCmSerialNumber This object represents the serial number of the Cable Modem that has been connected to the AP.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: `range: 0..255`	`.1.3.6.1.4.1.9.9.513.1.2.12.1.7`
cLApCmUsChannelStatus This object represents the upstream channel Status of the Cable Modem that has been connected to the AP.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: `range: 0..255`	`.1.3.6.1.4.1.9.9.513.1.2.12.1.8`
cLApCmDsChannelStatus This object represents the downstream Channel Status of the Cable Modem that has been connected to the AP.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: `range: 0..255`	`.1.3.6.1.4.1.9.9.513.1.2.12.1.9`
cLApCmMaskBit This object represents the mask bit of the Cable Modem based on the mask value the CM statistics is displayed for the AP.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: `range: 0..255`	`.1.3.6.1.4.1.9.9.513.1.2.12.1.10`

cLApFastHbTimerTable

table

.1.3.6.1.4.1.9.9.513.1.3.1 · 1 row entry · 3 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApFastHbTimerTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApFastHbTimerTable'

This table contains entries for AP fast heartbeat
timers configured in the controller. At startup,
all the entries in this table are set up by the central
controller.  A management application can later change
the values in this table.

cLApFastHbTimerEntry row .1.3.6.1.4.1.9.9.513.1.3.1.1

A conceptual row in cLApFastHbTimerTable. There is an entry
in this table for each AP type, as identified by a value of
cLApFastHbTimerApType.

Indexes

cLApFastHbTimerApType

Column Syntax OID

cLApFastHbTimerApType

This object represents the AP type for this entry.
local - indicates that timer is for local mode APs
hreap - indicates that timer is for HREAP APs

Enumeration

Enumerated Values:

1	local
2	hreap

.1.3.6.1.4.1.9.9.513.1.3.1.1.1

cLApFastHbTimerTimeout

This object specifies the timeout value for the heart
beat timer. This value changes to 0 when
cLApFastHbTimerEnabled is set to 'false'.

secondsUnsigned32r/w

Constraints:
range: 1-15

.1.3.6.1.4.1.9.9.513.1.3.1.1.2

cLApFastHbTimerEnabled

This object specifies the heartbeat timer. A value of 'true'
indicates that this timer is enabled. A value of 'false'
indicates that this timer is disabled.

cLApGlobalDot11IfCdpEnabled

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.3.1.1.3

cLApGlobalDot11IfTable

table

.1.3.6.1.4.1.9.9.513.1.3.12 · 1 row entry · 1 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApGlobalDot11IfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApGlobalDot11IfTable'

This table is used to configure the global dot11
parameters per slot id, represented by cLApDot11IfSlotId, 
of the radio interface in all the APs joined with 
the controller.

cLApGlobalDot11IfEntry row .1.3.6.1.4.1.9.9.513.1.3.12.1

This represents an entry in the
cLApGlobalDot11IfTable.

Indexes

cLApDot11IfSlotId

Column Syntax OID

This object specifies to configure the Cisco Discovery
Protocol(CDP) in the interface, represented by
cLApDot11IfSlotId of the all the APs, joined in the
controller.

Setting this object to a value of 'tr…

cLApGlobalEthernetIfCdpEnabled

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.3.12.1.1

cLApGlobalEthernetIfTable

table

.1.3.6.1.4.1.9.9.513.1.3.13 · 1 row entry · 1 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApGlobalEthernetIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApGlobalEthernetIfTable'

This table is used to configure the global parameters
on Ethernet interfaces of all the APs joined with the 
controller.

cLApGlobalEthernetIfEntry row .1.3.6.1.4.1.9.9.513.1.3.13.1

This represents an entry in
cLApGlobalEthernetIfTable.

Indexes

cLApEthernetIfSlotId

Column Syntax OID

This object is specifies to configure the Cisco Discovery
Protocol(CDP) in the interface, represented by
cLApEthernetIfSlotId of the all the APs, joined in
the controller.

Setting this object to a value …

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.3.13.1.1

cLApCredentialsTable

table

.1.3.6.1.4.1.9.9.513.1.4.4 · 1 row entry · 4 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApCredentialsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApCredentialsTable'

This table provides the information about the credentials
of the 802.11 LWAPP Access Points that have joined the 
controller. Rows are added to this table whenever, new APs 
are joined to this controller, and rows are deleted 
whenever APs gets disjoined from the controller.

cLApCredentialsEntry row .1.3.6.1.4.1.9.9.513.1.4.4.1

Each entry in this table provides information about
one 802.11 LWAPP Access Point that has joined the
controller. cLApSysMacAddress is the index which
uniquely identifies every row in the table.

Indexes

Column Syntax OID

cLApCredentialUserName

This object specifies the username for
this AP.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.4.4.1.1

cLApCredentialPassword

This object specifies the password corresponding to
user name represented by cLApCredentialUserName object.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.4.4.1.2

cLApCredentialSecret

This object specifies the secret key for
the specific AP. This provides the read-write access
on the console for this AP.

cLApCredentialEnableGlobalCredentials

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.4.4.1.3

This object specifies whether the global credentials
for the AP is enabled or disabled.

A value of 'true' indicates the global username/password
to be used for this AP .
A value of 'false' indicates the …

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.4.4.1.4

cLApLinkLatencyTable

table

.1.3.6.1.4.1.9.9.513.1.5.1 · 1 row entry · 2 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApLinkLatencyTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApLinkLatencyTable'

This table represents the link latency configuration
for each AP. 
An entry is automatically added to this table when 
an Access Points Joins controller. 
Entry is removed from this table when AP 
disassociates from the controllers.

cLApLinkLatencyEntry row .1.3.6.1.4.1.9.9.513.1.5.1.1

Each entry in this table provides configuration
related to Link latency on each AP.

Indexes

Column Syntax OID

cLApLinkLatencyEnable

This object specifies to configure the Link
Latency on the AP.
A value of 'true' indicates that the Link Latency
is enabled.
A value of 'false' indicates that the Link Latency
is disabled.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.5.1.1.1

cLApLinkLatencyReset

This object specifies to reset the Link Latency
stored at controller for an AP.
A value of 'true' indicates that the Link Latency stats
is to be reset.
A value of 'false' on this during set will return err…

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.5.1.1.2

cLApLinkLatencyStatsTable

table

.1.3.6.1.4.1.9.9.513.1.5.2 · 1 row entry · 8 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApLinkLatencyStatsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApLinkLatencyStatsTable'

This table represents the link latency statistics
calculated for each AP. 
An entry is automatically added by the controller
when a 'cLApLinkLatencyEnable' is enabled on an 
Access Point. Entry is deleted when 
'cLApLinkLatencyEnable' is disabled on the 
Access Point.

cLApLinkLatencyStatsEntry row .1.3.6.1.4.1.9.9.513.1.5.2.1

Each entry in this table provides minimum, maximum
and average Link latency for a Access Point.
Entries are removed when the Link Latency is disabled
on a Access Point.

Indexes

Column	Syntax	OID
cLApLinkLatencyStatsCurrent This object represents the current Link latency recorded for this Access point.	millisecondsSNMPv2-TCTimeInterval Type Constraints: `range: 0..2147483647` Description: A period of time, measured in units of 0.01 seconds.	`.1.3.6.1.4.1.9.9.513.1.5.2.1.1`
cLApLinkLatencyStatsMin This object represents the minimum Link latency recorded for this Access point.	millisecondsSNMPv2-TCTimeInterval Type Constraints: `range: 0..2147483647` Description: A period of time, measured in units of 0.01 seconds.	`.1.3.6.1.4.1.9.9.513.1.5.2.1.2`
cLApLinkLatencyStatsMax This object represents the maximum Link latency recorded for this Access point.	millisecondsSNMPv2-TCTimeInterval Type Constraints: `range: 0..2147483647` Description: A period of time, measured in units of 0.01 seconds.	`.1.3.6.1.4.1.9.9.513.1.5.2.1.3`
cLApLinkLatencyTimeStamp This object represents the timestamp, when the values are collected, as returned by the object 'cLApUpTime'.	secondsSNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	`.1.3.6.1.4.1.9.9.513.1.5.2.1.4`
cLApDataLinkLatencyStatsCurrent This object represents the current Data Link latency recorded for this Access point.	millisecondsSNMPv2-TCTimeInterval Type Constraints: `range: 0..2147483647` Description: A period of time, measured in units of 0.01 seconds.	`.1.3.6.1.4.1.9.9.513.1.5.2.1.5`
cLApDataLinkLatencyStatsMin This object represents the minimum Data Link latency recorded for this Access point.	millisecondsSNMPv2-TCTimeInterval Type Constraints: `range: 0..2147483647` Description: A period of time, measured in units of 0.01 seconds.	`.1.3.6.1.4.1.9.9.513.1.5.2.1.6`
cLApDataLinkLatencyStatsMax This object represents the maximum Data Link latency recorded for this Access point.	millisecondsSNMPv2-TCTimeInterval Type Constraints: `range: 0..2147483647` Description: A period of time, measured in units of 0.01 seconds.	`.1.3.6.1.4.1.9.9.513.1.5.2.1.7`
cLApDataLinkLatencyTimeStamp This object represents the timestamp, when the values are collected, as returned by the object 'cLApUpTime'.	secondsSNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	`.1.3.6.1.4.1.9.9.513.1.5.2.1.8`

cLAp802dot1xSupplicantTable

table

.1.3.6.1.4.1.9.9.513.1.7.4 · 1 row entry · 4 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLAp802dot1xSupplicantTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLAp802dot1xSupplicantTable'

This table provides the information about the 802.1x
Supplicant credentials of the 802.11 LWAPP Access Points 
that have joined the controller. Rows are added to this 
table whenever, new APs are joined to this controller, 
and rows are deleted whenever APs gets disjoined from 
the controller.

cLAp802dot1xSupplicantEntry row .1.3.6.1.4.1.9.9.513.1.7.4.1

Each entry in this table provides information about
one 802.11 LWAPP Access Point that has joined the
controller. cLApSysMacAddress is the index which
uniquely identifies every row in the table.

Indexes

cLAp802dot1xSupplicantOverrideEnabled

Column Syntax OID

This object specifies the individual AP level 802.1x
Supplicant Authentication override parameters.
A value of 'true' indicates user can override the Global AP
8021.1x authentication credentials by providing individual…

cLAp802dot1xSupplicantOverrideUsername

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.7.4.1.1

This object specifies the individual AP level 802.1x
supplicant override username.

cLAp802dot1xSupplicantOverridePassword

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.7.4.1.2

This object the individual AP level 802.1x supplicant
override password. A query on this OID will always
return '****'.

cLAp802dot1xSupplicantOverrideEapType

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.7.4.1.3

This object specifies the EAP type to be
applied for ap port auth as AP override config.

Enumerationr/w

Enumerated Values:

1	none
2	eapFast
3	eapTls
4	peap

.1.3.6.1.4.1.9.9.513.1.7.4.1.4

cLApSeClientTable

table

.1.3.6.1.4.1.9.9.513.1.8 · 1 row entry · 6 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApSeClientTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApSeClientTable'

This table represents the information about the
details of Spectrum Expert client connected to 
radio interface of APs

cLApSeClientEntry row .1.3.6.1.4.1.9.9.513.1.8.1

An entry in this table represents the details of
Spectrum Expert client connected to APs

Indexes

cLApSysMacAddress cLApDot11IfSlotId cLApSeIndex

Column Syntax OID

cLApSeIndex

This object indicates the index of the client
running the Spectrum Expert instance.

Integer32

Constraints:
range: 0-2

.1.3.6.1.4.1.9.9.513.1.8.1.1

cLApSeClientUserName

This object represents the name of the
client running the Spectrum Expert application

INET-ADDRESS-MIBInetAddressType

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.8.1.2

cLApSeClientIPAddrType

This object represents the client IP address type,
that runs the SE application, made available
through cLApSeClientIPAddr

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.9.9.513.1.8.1.3

cLApSeClientIPAddr

This object represents the client IP address,
that runs the SE application

INET-ADDRESS-MIBInetAddress

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.8.1.4

cLApSeClientDuration

This object represents the duration for which the SE client
application has been up and running

SNMPv2-TCTimeInterval

Type Constraints:
range: 0..2147483647

Description:

A period of time, measured in units of 0.01 seconds.

.1.3.6.1.4.1.9.9.513.1.8.1.5

cLApSeClientPort

This object represents the port from which the SE client
application is running

INET-ADDRESS-MIBInetPortNumber

Type Constraints:
range: 0..65535

.1.3.6.1.4.1.9.9.513.1.8.1.6

cLApWlanStatsTable

table

.1.3.6.1.4.1.9.9.513.1.9.1 · 1 row entry · 7 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApWlanStatsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApWlanStatsTable'

This table represents Per-AP, Per-Radio, Per-SSID
Stats information of packets/bytes sent/received,
retransmission counter, associated clients counter,
etc.

cLApWlanStatsEntry row .1.3.6.1.4.1.9.9.513.1.9.1.1

This entry contains stats information of
packets/bytes sent/received, retransmission counter,
associated clients counter, and etc.

Indexes

cLApSysMacAddress cLApDot11IfType CISCO-LWAPP-WLAN-MIBcLWlanIndex

Column	Syntax	OID
cLApWlanStatsTxPktNum This object represents the transmitted packets counter of the specific radio and wlan on this access point.	packetsSNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.9.9.513.1.9.1.1.1`
cLApWlanStatsTxOctetNum This object represents the transmitted bytes counter of the specific radio and wlan on this access point.	packetsSNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.9.9.513.1.9.1.1.2`
cLApWlanStatsRxPktNum This object represents the received packets counter of the specific radio and wlan on this access point.	packetsSNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.9.9.513.1.9.1.1.3`
cLApWlanStatsRxOctetNum This object represents the received bytes counter of the specific radio and wlan on this access point.	packetsSNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.9.9.513.1.9.1.1.4`
cLApWlanStatsRetransmitNum This object represents the packet retransmission counter of the specific radio and wlan on this access point.	packetsSNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.9.9.513.1.9.1.1.5`
cLApWlanStatsAssocClientNum This object represents the associated client counter of the specific radio and wlan on this access point.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.9.1.1.6`
cLApWlanStatsOnlineUserNum This object represents the online user counter of the specific radio and wlan on this access point.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.9.9.513.1.9.1.1.7`

cLApWlanInfoTable

table

.1.3.6.1.4.1.9.9.513.1.10.1 · 1 row entry · 1 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApWlanInfoTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApWlanInfoTable'

This table represents Per-AP, Per-SSID
information of max supported clients

cLApWlanInfoEntry row .1.3.6.1.4.1.9.9.513.1.10.1.1

Each entry in this table represents the information about
clients associated to a wlan broadcasted by an access point.

Indexes

cLApSysMacAddress CISCO-LWAPP-WLAN-MIBcLWlanIndex

Column	Syntax	OID
cLApWlanInfoMaxClients This object specifies the maximum supported clients per WLAN .	Unsigned32r/w Constraints: `range: 1-600`	`.1.3.6.1.4.1.9.9.513.1.10.1.1.1`

cLApRadioWlanInfoTable

table

.1.3.6.1.4.1.9.9.513.1.10.2 · 1 row entry · 2 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApRadioWlanInfoTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApRadioWlanInfoTable'

This table represents Per-AP, Per-radio,
Per-SSID information.

cLApRadioWlanInfoEntry row .1.3.6.1.4.1.9.9.513.1.10.2.1

This entry contains information of
Per-AP, Per-RADIO, Per-SSID information.

Indexes

cLApSysMacAddress cLApDot11IfSlotId CISCO-LWAPP-WLAN-MIBcLWlanIndex

Column	Syntax	OID
cLApRadioWlanSsid This object represents SSID of the particular WLAN, which is seen on the radio of the AP.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: `range: 0..255`	`.1.3.6.1.4.1.9.9.513.1.10.2.1.1`
cLApRadioWlanBssid This object represents the BSSID of the SSID on this radio of this AP.	SNMPv2-TCMacAddress Type Constraints: `range: 6` Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	`.1.3.6.1.4.1.9.9.513.1.10.2.1.2`

cLAplanStatsTable

table

.1.3.6.1.4.1.9.9.513.1.12.1 · 1 row entry · 6 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLAplanStatsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLAplanStatsTable'

This table represents Saridinia AP LAN stats
information that have joined the controller.

cLAplanStatsEntry row .1.3.6.1.4.1.9.9.513.1.12.1.1

This entry contains stats information of
LAN stats

Indexes

cLApSysMacAddress cLApLanPortId

Column Syntax OID

cLApLanPortId

This object represents the ID of a LAN
port of an AP.

Integer32

Constraints:
range: 1-4

.1.3.6.1.4.1.9.9.513.1.12.1.1.1

cLApLanPortState

This object specifies the state of an
ethernet interface of AP.
A value of 'true' indicates admin status of
ethernet interface is up.
A value of 'false' indicates admin status of
ethernet interface is down.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.12.1.1.2

cLApLanPortVlanId

This object specifies the Vlan Id of
the ethernet interface. When the value is 0 ,
the VLAN access is disabled.

Unsigned32r/w

Constraints:
range: 0-4094

.1.3.6.1.4.1.9.9.513.1.12.1.1.3

cLApLanPortVlanIdValid

This object represents VLAN ID is valid or not
for an ethernet interface.
A value of 'true' indicates vlanId is valid.
A value of 'false' indicates vlanId is not valid.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.12.1.1.4

cLApLanPoeState

This object specifies the LAN PoE Status of an
ethernet interface of an AP.
A value of 'true' indicates poe state is enabled for
ethernet interface.
A value of 'false' indicates poe state is disabled for
ethernet inter…

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.12.1.1.5

cLApLanPowerLevelId

This object specifies the power level
of the port

Unsigned32r/w

Constraints:
range: 1-4

.1.3.6.1.4.1.9.9.513.1.12.1.1.6

cLAplanOverrideTable

table

.1.3.6.1.4.1.9.9.513.1.12.2 · 1 row entry · 1 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLAplanOverrideTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLAplanOverrideTable'

This table represents the lan override status of an AP

cLAplanOverrideEntry row .1.3.6.1.4.1.9.9.513.1.12.2.1

This entry contains stats information of LAN override status

Indexes

Column Syntax OID

cLApLanOverride

This object specifies the LAN port override status of AP.
A value of 'true' indicates LAN override is enabled.
A value of 'false' indicates LAN override is disabled.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.12.2.1.1

cLHaloBleBeaconTable

table

.1.3.6.1.4.1.9.9.513.1.13.2 · 1 row entry · 4 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLHaloBleBeaconTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLHaloBleBeaconTable'

This table represents the BLE global configuration.It lists
the ibeacon's identification number and attenuation value
which is common to HALO enabled AP's that 
have joined the controller.

cLHaloBleBeaconEntry row .1.3.6.1.4.1.9.9.513.1.13.2.1

This entry contains BLE global configuration which lists
the ibeacon's identification number and attenuation value
of HALO enabled APs that have joined the controller.

Indexes

cLHaloGlobalBleBeaconId

Column Syntax OID

cLHaloGlobalBleBeaconId

This object represents the BLE ibeacon ID for
which gloabl BLE configurations to be
applied.

cLHaloGlobalBleBeaconUuid

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.13.2.1.1

This object specifies the UUID (universally unique identifier)
which is a 128-bit value.

OctetStringr/w

Constraints:
range: 0-128

.1.3.6.1.4.1.9.9.513.1.13.2.1.2

cLHaloGlobalBleBeaconTxPower

This object specifies TX power of particular ibeacon for
HALO enabled APs that have joined the controller.The TX power
is based on size of proximity zone needed.

dBmUnsigned32r/w

Constraints:
range: 0-52

.1.3.6.1.4.1.9.9.513.1.13.2.1.3

cLHaloGlobalBleBeaconEnable

This object specifies the status of the BLE beacons.
A value of 'true' indicates BLE beacon is enabled.
A value of 'false' indicates BLE beacon is disabled.

cLApSysMacAddress cLHaloGlobalBleBeaconId

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.13.2.1.4

cLApBleBeaconTable

table

.1.3.6.1.4.1.9.9.513.1.13.3 · 1 row entry · 8 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApBleBeaconTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApBleBeaconTable'

This table represents BLE ibeacon's AP specific configuration
for HALO enabled APs that have joined the controller.

cLApBleBeaconEntry row .1.3.6.1.4.1.9.9.513.1.13.3.1

This entry contains BLE Beacon's AP specific configuration.

Indexes

Column Syntax OID

cLApBleBeaconMajorField

This object specifies the Major value of ibeacon
that is used to differentiate ibeacons that have the same
proximity UUID.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.13.3.1.1

cLApBleBeaconMinorField

This object specifies the Minor value of ibeacon
that is used to differentiate ibeacons that have the same
proximity UUID and has same major value.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.13.3.1.2

cLApBleBeaconTxPower

This object specifies TX power of particular ibeacon for
specified HALO enabled AP. The TX power value is based on
the size of proximity zone needed.

dBmUnsigned32r/w

Constraints:
range: 0-52

.1.3.6.1.4.1.9.9.513.1.13.3.1.3

cLApBleBeaconStatus

This object specifies the status of the BLE beacons.
A value of 'true' indicates BLE beacon is enabled,
A value of 'false' indicates BLE beacon is disabled.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.13.3.1.4

cLApBleBeaconUuid

This object specifies the UUID (universally unique identifier)
which is a 128-bit value.

OctetStringr/w

Constraints:
range: 0-128

.1.3.6.1.4.1.9.9.513.1.13.3.1.5

cLApBleBeaconInterval

This object specifies the beacon interval
between each transmissions from BLE module.
This value is common to HALO enabled APs that
have joined the controller.

HzUnsigned32r/w

Constraints:
range: 1-10

.1.3.6.1.4.1.9.9.513.1.13.3.1.6

cLApBleBeaconApplyGlobal

This object specifies to clear all BLE configuration at AP.
A value of 'true' indicates configurations need to be cleared.
A value of 'false' indicates configurations need not be
cleared.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.13.3.1.7

cLApBleBeaconAdvTxPower

This object specifies the beacon advertised transmission
power in the BLE beacon payload.
This value is common to all beacons for a single AP.

HzUnsigned32r/w

Constraints:
range: 40-100

.1.3.6.1.4.1.9.9.513.1.13.3.1.8

cLApHyperlocationTable

table

.1.3.6.1.4.1.9.9.513.1.14.1 · 1 row entry · 2 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApHyperlocationTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApHyperlocationTable'

This table represents the information about the
APs hyperlocation state and its config nature 
controller.

cLApHyperlocationEntry row .1.3.6.1.4.1.9.9.513.1.14.1.1

Each entry in this table provides information about
Hyperlocation state and config nature of APs
controller.

Indexes

cLApHyperlocationAdminState

Column Syntax OID

This object specifies the hyperlocation admin state
for an AP to be enabled or disabled.
A value of 'true' indicates admin state of HALO module
is up.
A value of 'false' indicates admin state of HALO module
is down.

cLApHyperlocationUnsetFlag

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.14.1.1.1

This object specifies explicit flag status
for AP need to be enabled or not.

A value of 'true' indicates AP has an explicit per AP config.
A value of 'false' indicates there is no AP config

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.14.1.1.2

cLApProfileTable

table

.1.3.6.1.4.1.9.9.513.1.16.1 · 1 row entry · 99 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApProfileTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApProfileTable'

This table provides the information about the Access Point
profiles. Access Point profile is a set of configuration which
can be different for APs at different site/location.
Rows are added or deleted by explicit management actions
initiated by the user from a network management station through
the cLApProfileRowStatus object.

cLApProfileEntry row .1.3.6.1.4.1.9.9.513.1.16.1.1

Each entry in this table represents the AP profile
configuration which can be applied to set of APs based on the
controller configuration. Entries can be added/deleted by
explicit management actions by NMS or by user co…

Indexes

cLApProfileName

Column Syntax OID

cLApProfileName

This object specifies one instance of an AP Profile on the
controller.

OctetString

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.16.1.1.1

cLApProfileRowStatus

This object specifies the row to be added or
deleted in this table.

cLApProfileCredentialGlobalUserName

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.9.9.513.1.16.1.1.2

This object specifies the global username for the APs
associated to a particular AP Profile.
This user name is used to access the console on the AP.

OctetStringr/w

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.16.1.1.3

cLApProfileCredentialGlobalPassword

This object specifies the password corresponding to
the user name represented by cLApProfileCredentialGlobalUserName
object.

OctetStringr/w

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.16.1.1.4

cLApProfileCredentialGlobalSecret

This object specifies the secret key for the APs associated
to particular AP profile. This provides read-write access
to the console on the AP.

OctetStringr/w

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.16.1.1.5

cLApProfileCredentialEnableGlobalCredentialsdeprecated

This object specifies whether the global credentials for the
APs associated to a particular AP Profile is enabled or
disabled.

A value of 'true' enables the global username/password
to be used for the AP…

cLApProfileLinkLatencyEnable

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.6

This object specifies to the configuration of the Link
Latency on the APs associated to a particular AP profile.
disable - disables the link latency on the APs associated to
a particular AP profile.
enable - e…

Enumerationr/w

Enumerated Values:

1	disable
2	enable
3	data
4	reset

.1.3.6.1.4.1.9.9.513.1.16.1.1.7

cLApProfileHaloBleBeaconInterval

This object specifies the time interval between HALO BLE
beacon transmissions.
This value is common to HALO enabled APs that have joined the
controller under the same AP profile.

HzUnsigned32r/w

Constraints:
range: 1-10

.1.3.6.1.4.1.9.9.513.1.16.1.1.8

cLApProfileFastHbTimerTimeout

This object specifies the timeout value for the Fast Heart Beat
timer of all the APs associated to the current AP Profile.

secondsUnsigned32r/w

Constraints:
range: 1-10

.1.3.6.1.4.1.9.9.513.1.16.1.1.12

cLApProfileFastHbTimerEnableddeprecated

This object specifies if Fast Heart Beat Timer is enabled or
not.
A value of 'true' indicates that this timer is enabled.
A value of 'false' indicates that this timer is disabled.

cLApProfilePrimaryDiscoveryTimeout

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.13

This object specifies the timeout value for the primary AP
discovery for a given Ap profile.

secondsUnsigned32r/w

Constraints:
range: 30-3000

.1.3.6.1.4.1.9.9.513.1.16.1.1.14

cLApProfileBackupPrimaryControllerAddressType

This object specifies the type of the primary controller's
address made available through
cLApProfileBackupPrimaryControllerAddress.

cLApProfileBackupPrimaryControllerAddress

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.9.9.513.1.16.1.1.15

This object specifies the address of the primary controller
that the APs in the profile should associate with. The name and
address should be provided in the same set request. An address
of all zeros will unset the prim…

cLApProfileBackupPrimaryControllerName

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.16.1.1.16

This object specifies the name of the primary controller
that the APs in the profile should associate with.

OctetStringr/w

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.16.1.1.17

cLApProfileBackupSecondaryControllerAddressType

This object specifies the type of the secondary
controller's address made available through
cLApProfileBackupSecondaryControllerAddress.

cLApProfileBackupSecondaryControllerAddress

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.9.9.513.1.16.1.1.18

This object specifies the address of the secondary
controller that the APs in the profile should associate with.
The name and address should be provided in the same
set request. An address of all zeros will unset the s…

cLApProfileBackupSecondaryControllerName

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.16.1.1.19

This object specifies the name of the secondary controller
that the APs in the profile should associate.

OctetStringr/w

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.16.1.1.20

cLApProfileBackupTertiaryControllerAddressType

This object specifies the type of the tertiary
controller's address made available through
cLApProfileBackupTertiaryControllerAddress.

cLApProfileBackupTertiaryControllerAddress

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.9.9.513.1.16.1.1.21

This object specifies the address of the tertiary
controller that the APs in the profile should associate with.
The name and address should be provided in the same
set request. An address of all zeros will unset the ter…

cLApProfileBackupTertiaryControllerName

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.16.1.1.22

This object specifies the name of the tertiary controller
that the APs in the profile should associate with

OctetStringr/w

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.16.1.1.23

cLApProfileTcpMss

This object specifies the AP TCP MSS value per AP profile.
The permissible value are between 536 and 1363. This will
also enable the global TCP MSS flag.
Any change of value for this object will be reflected
to cLApTcp…

Unsigned32r/w

Constraints:
range: 536-1363

.1.3.6.1.4.1.9.9.513.1.16.1.1.25

cLApProfileRetransmitCount

This object specifies the retransmission count for the
control packet for all APs associated to this particular AP
profile. This value represents the number of packets
retransmitted after which the Access Point falls b…

retriesUnsigned32r/w

Constraints:
range: 3-8

.1.3.6.1.4.1.9.9.513.1.16.1.1.26

cLApProfileRetransmitTimeout

This object specifies the retransmission timeout for the
control packet for all APs associated to this particular AP
profile. This value represents the timeout for each
control Packet of all the Access Points, joined t…

secondsUnsigned32r/w

Constraints:
range: 2-5

.1.3.6.1.4.1.9.9.513.1.16.1.1.27

cLApProfileOeapDisableLocalAccessdeprecated

This object specifies whether the local access is supported for
all the Office Extended Access Points associated to current AP
Profile. If set to true, the local SSID and and LAN ports on
the OEAP will be disabled.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.28

cLApProfileLedState

This object specifies whether the LED state of all the
access points associated to a profile should be enabled or
disabled.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.29

cLApProfileRadioInterfaceShutdownEnableddeprecated

This object allows the user to enable or disable radio
interface of all the APs associated to current AP Profile.
When enabled, AP radio's will be shut down when ethernet link
goes down for a duration of time set for
c…

cLApProfileMulticastGroupAddressType

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.30

cLApProfileEthernetInterfaceDowntimedeprecated

This object specifies the ethernet interface down time after
which the AP radio interface will be shut down for Aps in a
profile.

SecondsSNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.16.1.1.31

This object specifies the AP multicast group address type.

cLApProfileMulticastGroupAddress

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.9.9.513.1.16.1.1.32

This object specifies the IPv6 multicast group address of all
the APs associated to current AP Profile.

cLApProfilePrimedJoinTimeout

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.16.1.1.33

cLApProfileMulticastMode

This object specifies the ethernet multicast support of all
the APs associated to current AP Profile.
unicast - Controller will convert multicast to
unicast packet.
multicast - Multicast mode is enabled.

Enumerationr/w

Enumerated Values:

1	unicast
2	multicast

.1.3.6.1.4.1.9.9.513.1.16.1.1.34

This object specifies the primed timeout for the AP
discovery for a given profile.

secondsUnsigned32r/w

Constraints:
range: 0-43200

.1.3.6.1.4.1.9.9.513.1.16.1.1.35

cLApProfilePreferMode

This object specifies the capwap tunnel prefer-mode for all APs
associated to this particular AP Profile.
unconfig - capwap tunnel is not established.
ipv4 - capwap tunnel established with ipv4 address.
ipv6 - capwap tu…

Enumerationr/w

Enumerated Values:

1	unconfig
2	ipv4
3	ipv6

.1.3.6.1.4.1.9.9.513.1.16.1.1.36

cLApProfileApLagEnabled

This object specifies the ap-lag capability state of all the
APs associated to current AP profile.
A value of 'true' indicates the ap-lag capability state is
enabled.
A value of 'false' indicates the ap-lag capability …

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.37

cLApProfile802dot1xAuthenticationEnableddeprecated

This object represents the 802.1x supplicant authentication
feature of APs associated to current AP Profile.
If configured as True, user can configure 8021.1x
authentication between lightweight access points and the
s…

cLApProfile802dot1xSupplicantUsername

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.38

This object represents the 802.1x supplicant username that
is to be inherited by all the APs associated to current AP
Profile.

OctetStringr/w

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.16.1.1.39

cLApProfile802dot1xSupplicantPassword

This object represents the 802.1x supplicant Password that
is to be inherited by all the APs associated to current AP
Profile.
A query on this OID will always return '****'.

OctetStringr/w

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.16.1.1.40

cLApProfileEncryptionEnable

This object specifies whether encyrption between
controller and AP is enabled or not in a profile. Encryption
can only be enabled if ESM card in controller is
pluged in.

A value of 'true' enables encrypt…

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.41

cLApProfileTelnetEnable

This object specifies whether Telnet session
can be established to the APs in a given AP profile.

A value of 'true' indicates an Telnet session
can be established to the APs in a given AP profile.
…

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.42

cLApProfileSshEnable

This object specifies whether SSH session
can be established to the APs asscoaited to an AP Profile.

A value of 'true' indicates an SSH session
can be established to the APs asscoaited to AP an Profile.
…

cLApProfileHyperlocationEnable

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.43

This object represents the admin status of Hyperlocation.
A value of 'true' indicates that Hyperlocation is enabled.
A value of 'false' indicates that Hyperlocation is disabled.

cLApProfileHyperlocationDetectionThreshold

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.44

This object represents the value of the Hyperlocation
detection threshold expressed in dBm. Valid range is
-100 dbm to -50 dbm.

dBmInteger32r/w

Constraints:
range: -100--50

.1.3.6.1.4.1.9.9.513.1.16.1.1.45

cLApProfileHyperlocationResetThreshold

This object represents the value of the Hyperlocation
reset threshold expressed in scan cycles. Valid range is
0 to 99 scan cycles. Its value must always be smaller
than the trigger threshold.

Unsigned32r/w

Constraints:
range: 0-99

.1.3.6.1.4.1.9.9.513.1.16.1.1.46

cLApProfileHyperlocationTriggerThreshold

This object represents the value of the Hyperlocation
trigger threshold expressed in scan cycles. Valid range
is 1 to 100 scan cycles.

Unsigned32r/w

Constraints:
range: 1-100

.1.3.6.1.4.1.9.9.513.1.16.1.1.47

cLApProfileHyperlocationNtpIpAddressType

This object represents the NTP server IP address type
configured for Hyperlocation feature.

cLApProfileHyperlocationNtpIpAddress

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.9.9.513.1.16.1.1.48

This object represents the NTP server IP address
configured for Hyperlocation feature.

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.16.1.1.49

cLApProfileAdjustMss

To enable the TCP MSS flag

cLApProfileDiscoveryTimeout

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.50

This object represents the timeout for the AP
discovery for a particular AP profile.

secondsUnsigned32r/w

Constraints:
range: 1-10

.1.3.6.1.4.1.9.9.513.1.16.1.1.51

cLApProfileHeartBeatTimeout

This object represents the Heart beat timeout for the APs in
a particular AP profile.

secondsUnsigned32r/w

Constraints:
range: 1-30

.1.3.6.1.4.1.9.9.513.1.16.1.1.52

cLApProfileCdpEnable

This object specifies to enable the CDP for all APs
associated to particular AP Profile

cLApProfileApPacketCaptureProfile

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.53

This object represents the AP packet capture profile
name mapped to this AP join profile. Access Points in this
AP join profile will use the parameters of packet capture
profile

OctetStringr/w

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.16.1.1.54

cLApProfileRogueReportInterval

This object specifies the rogue report interval,
which is the interval that monitor mode APs send
rogue detection details to the controller.
This value is valid only for the current AP Profile.

secondsUnsigned32r/w

Constraints:
range: 10-300

.1.3.6.1.4.1.9.9.513.1.16.1.1.55

cLApProfileRogueMinimumRssi

This object specifies the minimum value of RSSI
considered for detection of rogues.
This value is valid only for the current AP Profile.

dBmInteger32r/w

Constraints:
range: -128--70

.1.3.6.1.4.1.9.9.513.1.16.1.1.56

cLApProfileRogueTransientInterval

This object specifies the rogue transient
interval for this AP Profile.

A value of '0' specifies that an AP sends
rogue detection details to the controller
as soon as it detects a rogue.

A …

Unsigned32r/w

Constraints:
range: 0-0
range: 120-1800

.1.3.6.1.4.1.9.9.513.1.16.1.1.57

cLApProfileRogueContainFlexconnect

This object specifies whether Rogue containment of
standalone flexconnect APs is enabled in this AP Profile.
A value of 'true' enables rogue containment.
A value of 'false' disables rogue containment.

cLApProfileRogueContainAutoRateEnable

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.58

This object specifies whether Rogue containment auto-rate
is enabled in this AP Profile.
A value of 'true' enables auto-rate.
A value of 'false' disables auto-rate.

cLApProfileRogueDetectionEnable

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.59

This object specifies whether Rogue Detection
is enabled in this AP Profile.
A value of 'true' enables Rogue Detection.
A value of 'false' disables Rogue Detection.
Rogue detection is not supported on sniffer
and rogue …

cLApProfileReportInterval24ghz

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.60

This object specifies the interval at which APs
connected will send client statitics for 802.11b radio for a
particular AP profile.

secondsInteger32r/w

Constraints:
range: 5-90

.1.3.6.1.4.1.9.9.513.1.16.1.1.61

cLApProfileReportInterval5ghz

This object specifies the interval at which APs
connected will send client statitics for 802.11a radio for a
particular AP profile

secondsInteger32r/w

Constraints:
range: 5-90

.1.3.6.1.4.1.9.9.513.1.16.1.1.62

cLApProfileDot1xApSwitchEapAuth

This object specifies Dot1x EAP type
in this AP Profile.

Enumerationr/w

Enumerated Values:

1	eapNone
2	eapFast
3	eapTls
4	peap

.1.3.6.1.4.1.9.9.513.1.16.1.1.63

cLApProfileDot1xApSwtichLscAuth

This object specifies Dot1x LSC AP Auth
type in this AP Profile.

Enumerationr/w

Enumerated Values:

1	authNone
2	authCapwapDtls
3	authDot1xPort
4	authBoth

.1.3.6.1.4.1.9.9.513.1.16.1.1.64

cLApProfileMeshProfileName

This object uniquely identifies a mesh profile in a
particular AP profile.

OctetStringr/w

Constraints:
range: 1-32

.1.3.6.1.4.1.9.9.513.1.16.1.1.65

cLApProfileUsbStatus

This object specifies USB status(enable/disable) to be applied
to all APs belonging to this AP join profile.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.66

cLApProfileVlanTaggingdeprecated

This object specifies whether the Vlan tagging of all the APs
associated to current AP Profile should be enabled or disabled.

cLApProfileExtModuleEnable

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.67

cLApProfileApCountryCodedeprecated

This object represents the AP country code mapped to this
AP join profile.

OctetStringr/w

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.16.1.1.68

This object specifies whether extended module
is enabled in this AP Profile.
A value of 'true' enables extended module.
A value of 'false' disables extended module.

cLApProfilePoePreStandardSwitchFlag

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.69

cLApProfileStatsTimer

This object specifies the duration of the
stats timer value in seconds.

secondsUnsigned32r/w

Constraints:
range: 0-65535

.1.3.6.1.4.1.9.9.513.1.16.1.1.70

This object specifies whether the Pre-standard
switch state as PoE option.
A value of 'true' enables Pre-standard switch.
A value of 'false' disables Pre-standard switch.

cLApProfilePoePowerInjectorSelection

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.71

This object specifies the Power over Ethernet (PoE) injector
state for all the APs associated to current AP profile.
A value of '1' represents the state of PoE injector is unknown.
A value of '2' represents the state of…

Enumerationr/w

Enumerated Values:

1	unknown
2	installed
3	override

.1.3.6.1.4.1.9.9.513.1.16.1.1.72

cLApProfilePoeInjectorSwitchMac

This object represents the MAC address of the
switch port that has a Power injector.

SNMPv2-TCMacAddressr/w

Type Constraints:
range: 6

Description:

.1.3.6.1.4.1.9.9.513.1.16.1.1.73

cLApProfileHaloBleBeaconAdvertisedPwr

This object specifies the Power for HALO BLE beacon
advertisement.

dBmUnsigned32r/w

Constraints:
range: 40-100

.1.3.6.1.4.1.9.9.513.1.16.1.1.74

cLApProfileTftpDownGradeAddressType

This object represents the TFTP servers
address type in use.

cLApProfileTftpDownGradeAddress

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.9.9.513.1.16.1.1.75

This object represents the TFTP servers
IP address.

cLApProfileTftpDownGradeFileName

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.16.1.1.76

This object represents the AP image downgrade
file name on the TFTP server.

OctetStringr/w

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.16.1.1.77

cLApProfileCoreDumpType

This object specifies whether coredump is enabled and
whether it is in compress or uncompress.
A value of '1' represents uncompressed form of core dump file.
A value of '2' represents compressed form of core dump file.
…

Enumerationr/w

Enumerated Values:

1	uncompress
2	compress
3	disable

.1.3.6.1.4.1.9.9.513.1.16.1.1.78

cLApProfileCoreDumpTftpAddressType

This object represents the TFTP server address type used
for AP core dump transfer.

cLApProfileCoreDumpTftpAddress

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.9.9.513.1.16.1.1.79

This object represents the TFTP server address used for AP
core dump transfer.

cLApProfileCoreDumpCoreFileName

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.16.1.1.80

This object represents core dump file name
on the TFTP server.

OctetStringr/w

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.16.1.1.81

cLApProfileBackupFallbackEnabled

This object represents fallback status of APs asscoaited
to an AP Profile.
A value of 'true' represents AP fallback enabled.
A value of 'false' represents AP fallback disabled.

cLApProfileClientRssiStatsEnabled

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.82

This object represents the status of Client RSSI
statistics from Access Point.
A value of 'true' represents Client RSSI statistics reporting from
AP is enabled.
A value of 'false' represents Client RSSI statistics rep…

cLApProfileClientRssiStatsReportInterval

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.83

This object represents Client RSSI statistics reporting interval
value in seconds.

secondsUnsigned32r/w

Constraints:
range: 30-300

.1.3.6.1.4.1.9.9.513.1.16.1.1.84

cLApProfileGasRateLimitEnable

This object represents the GAS limit status of APs associated
to an AP Profile.
A value of 'true' represents AP GAS limit enabled.
A value of 'false' represents AP GAS disabled.

cLApProfileGasRateLimitNumReqPerInterval

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.85

This object specifies the maximum number of GAS messages
per interval.

packetsInteger32r/w

Constraints:
range: 1-100

.1.3.6.1.4.1.9.9.513.1.16.1.1.86

cLApProfileGasRateLimitIntervalMsec

This object specifies the interval for GAS message limit.

millisecondsInteger32r/w

Constraints:
range: 100-10000

.1.3.6.1.4.1.9.9.513.1.16.1.1.87

cLApProfileQoSMapApTrustsUpstreamDSCP

This object specifies whether the APs associated
with an AP Profile use the upstream/received DSCP
for outer CAPWAP tunnel QoS marking instead of
802.11 User Priority.
A value of 'true' represents using the upstream DSC…

cLApProfileMethodListName

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.88

cLApProfileUdpliteState

This object specifies the capwap tunnel ipv6 UDP-Lite checksum type
for all APs associated to this particular AP Profile.
unconfig - capwap tunnel is not established.
udplite_enabled - capwap tunnel established with ip…

Enumerationr/w

Enumerated Values:

1	unconfig
2	udpliteenabled
3	udplitedisabled

.1.3.6.1.4.1.9.9.513.1.16.1.1.89

This object specifies the method list used for the AP
accounting

cLApProfileCredentialGlobalSecretType

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.16.1.1.90

cLApProfileWindowSize

This object specifies the capwap window size for
capwap multiwindow

Integer32r/w

Constraints:
range: 1-50

.1.3.6.1.4.1.9.9.513.1.16.1.1.91

This object specifies the secret password type corresponding to
the secret password type represented by cLApProfileCredentialGlobalSecret
object.

Enumerationr/w

Enumerated Values:

0	clear
8	aes

.1.3.6.1.4.1.9.9.513.1.16.1.1.92

cLApProfileCredentialGlobalPasswordType

This object specifies the secret password type corresponding to
the secret password type represented by cLApProfileCredentialGlobalSecret
object.

Enumerationr/w

Enumerated Values:

0	clear
8	aes

.1.3.6.1.4.1.9.9.513.1.16.1.1.93

cLApProfile802dot1xSupplicantPasswordType

This object specifies the dot1xSupplicant password type corresponding to
the dot1xSupplicantPassword represented by
cLApProfile802dot1xSupplicantPassword object.

Enumerationr/w

Enumerated Values:

0	clear
8	aes

.1.3.6.1.4.1.9.9.513.1.16.1.1.94

cLApProfileBssidEnableStats

This object specifies whether the BSSID stats feature
is enabled or disabled per ap config profile
- A value of 'true' represents the BSSID stats as enabled.
- A Value of 'false' represents the BSSID stats as disabled.

cLApProfileBssidStatsFrequency

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.95

This object specifies the BSSID stats frequency set on the AP for
sending the stats in the current AP profile

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.9.9.513.1.16.1.1.96

cLApProfilePersistentSsidBroadcastEnable

This object specifies whether persistent SSID broadcast
is enabled or disabled per ap config profile
- A value of 'true' represents persistent SSID broadcast is enabled.
- A Value of 'false' represents persistent SSID …

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.97

cLApProfileDhcpFallback

This object specifies whether the AP fallback to DHCP
is enabled or disabled per ap config profile
- A value of 'true' represents that AP moves to DHCP if it fails to join controller via static IP.
- A Value of 'false'…

cLApProfileOeapRogueDetectionEnable

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.98

This object specifies whether Rogue Detection
is enabled for OEAP.
A value of 'true' indicates rogue detection is enabled.
A value of 'false' indicates rogue detection is disabled.

cLApProfileOeapEncryptionEnable

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.99

This object specifies whether encyrption between
controller and OEAP is enabled or not in a profile.

A value of 'true' enables encryption between
controller and AP.

A value of 'false' disab…

cLApProfileOeapLocalAccessEnable

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.100

This object specifies Personal SSID
broadcast

A value of 'true' enables local access of
AP Webui

A value of 'false' disables local access of
AP Webui.

cLApProfileOeapProvSsidEnable

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.101

This object specifies Provisional SSID
broadcast

A value of 'true' enables broadcast of
Provisional SSID

A value of 'false' disables broadcast of
Provisional SSID.

cLApProfileName cLApProfileHaloBleBeaconId

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.1.1.102

cLApProfileCountryCode

This object specifies the country code for all APs
associated to this particular AP Profile.

Enumerationr/w

Enumerated Values:

1	ae
2	al
3	ar
4	at
5	au
6	ba
7	bb
8	bd
9	be
10	bg
11	bh
12	bm
13	bn
14	bo
15	br
16	belarus
17	ca
18	ch
19	cl
20	cm
21	cn
22	co
23	cr
24	cu
25	cy
26	cz
27	de
28	dk
29	do
30	dz
31	ec
32	ee
33	eg
34	el
35	es
36	fi
37	fj
38	fr
39	gb
40	gh
41	gi
42	gr
43	hk
44	hr
45	hu
46	id
47	ie
48	il
49	in
50	io
51	iq
52	is
53	it
54	j2
55	j4
56	jm
57	jo
58	ke
59	kn
60	kw
61	kz
62	lb
63	li
64	lk
65	lt
66	lu
67	lv
68	ly
69	ma
70	mc
71	me
72	mk
73	mn
74	mo
75	mt
76	mx
77	my
78	ng
79	nl
80	no
81	nz
82	om
83	pa
84	pe
85	ph
86	pk
87	pl
88	pr
89	pt
90	py
91	qa
92	ro
93	rs
94	ru
95	sa
96	se
97	sg
98	si
99	sk
100	th
101	ti
102	tn
103	tr
104	tw
105	ua
106	us
107	uy
108	ve
109	vn
110	za
111	unconfigured

.1.3.6.1.4.1.9.9.513.1.16.1.1.103

cLApProfileHaloBleBeaconTable

table

.1.3.6.1.4.1.9.9.513.1.16.2 · 1 row entry · 5 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApProfileHaloBleBeaconTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApProfileHaloBleBeaconTable'

This table represents an instance of HALO BLE configuration per
AP profile. It lists the HALO BLE beacon parameters which are 
common for HALO enabled APs that have joined the controller 
under the same AP profile.

cLApProfileHaloBleBeaconEntry row .1.3.6.1.4.1.9.9.513.1.16.2.1

This entry contains an instance of HALO BLE beacon
configuration for a specific AP profile. It lists the HALO BLE
beacon ID, UUID, transmission power, and status per beacon for
HALO enabled APs of a particular AP prof…

Indexes

Column Syntax OID

cLApProfileHaloBleBeaconId

This object represents HALO BLE beacon ID for which BLE
configuration to be applied.

Unsigned32

Constraints:
range: 0-4

.1.3.6.1.4.1.9.9.513.1.16.2.1.1

cLApProfileHaloBleBeaconUuid

This object represents HALO BLE beacon UUID (universally
unique identifier) which is a 128-bit value.

OctetStringr/w

Constraints:
range: 0-128

.1.3.6.1.4.1.9.9.513.1.16.2.1.2

cLApProfileHaloBleBeaconTxPower

This object represents HALO BLE beacon transmission power.
The transmission power is based on the size of the required
proximity zone.

dBmUnsigned32r/w

Constraints:
range: 0-52

.1.3.6.1.4.1.9.9.513.1.16.2.1.3

cLApProfileHaloBleBeaconEnabled

This object specifies the status of HALO BLE beacon.
true(1) - enable the HALO BLE beacon,
false(2) - disable the HALO BLE beacon.

cLApProfileHaloBleBeaconRowStatus

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.16.2.1.4

This object specifies the row to be added or
deleted in this table.

cLApProfileName cLApProfileQosMapRangeUP

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.9.9.513.1.16.2.1.5

cLApProfileQosMapRangeTable

table

.1.3.6.1.4.1.9.9.513.1.16.3 · 1 row entry · 5 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApProfileQosMapRangeTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApProfileQosMapRangeTable'

This table represents an instance of QoS Map configuration per
AP profile. It lists the QoS Map DSCP-to-User Priority ranges
which are common for APs that have joined the controller under
the same AP profile.

cLApProfileQosMapRangeEntry row .1.3.6.1.4.1.9.9.513.1.16.3.1

This entry contains an instance of QoS Map configuration for
a specific AP profile. It lists the QoS Map DSCP lower range,
DSCP upper range, 802.11 User Priority and default DSCP
for upstream User Priority for APs of a …

Indexes

Column Syntax OID

cLApProfileQosMapRangeUP

This object represents the 802.11 User Priority
for which the DSCP-to-User Priority range
configuration is applied.

Integer32

Constraints:
range: 0-7

.1.3.6.1.4.1.9.9.513.1.16.3.1.1

cLApProfileQosMapRangeDSCPLower

This object represents the DSCP lower range
for which the DSCP-to-User Priority range configuration
is applied on the AP using an AP profile.

Integer32r/w

Constraints:
range: 0-63

.1.3.6.1.4.1.9.9.513.1.16.3.1.2

cLApProfileQosMapRangeDSCPUpper

This object represents the DSCP upper range
for which the DSCP-to-User Priority range configuration
is applied on the AP using an AP profile.

Integer32r/w

Constraints:
range: 0-63

.1.3.6.1.4.1.9.9.513.1.16.3.1.3

cLApProfileQosMapRangeUPToDSCP

This object represents the DSCP value which should
be used for the upstream 802.11 User Priority
on the AP using an AP profile.

Integer32r/w

Constraints:
range: 0-63

.1.3.6.1.4.1.9.9.513.1.16.3.1.4

cLApProfileQosMapRangeRowStatus

This object specifies the row to be added or
deleted in this table.

cLApProfileName cLApProfileQosMapExceptionDSCP

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.9.9.513.1.16.3.1.5

cLApProfileQosMapExceptionTable

table

.1.3.6.1.4.1.9.9.513.1.16.4 · 1 row entry · 3 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApProfileQosMapExceptionTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApProfileQosMapExceptionTable'

This table represents an instance of QoS Map configuration per
AP profile. It lists the QoS Map DSCP-to-User Priority
exceptions which are common for APs that have joined the
controller under the same AP profile.

cLApProfileQosMapExceptionEntry row .1.3.6.1.4.1.9.9.513.1.16.4.1

This table represents an instance of QoS Map configuration per
AP profile. It lists the QoS Map DSCP-to-User Priority
exceptions which are common for APs that have joined the
controller under the same AP profile.

Indexes

Column Syntax OID

cLApProfileQosMapExceptionDSCP

This object represents the DSCP value for the DSCP to 802.11
User Priority mapping exception for the APs that joined
the controller under the same AP profile.

Integer32

Constraints:
range: 0-63

.1.3.6.1.4.1.9.9.513.1.16.4.1.1

cLApProfileQosMapExceptionUP

This object represents the 802.11 User Priority value for the
DSCP to 802.11 User Priority mapping exception for the APs that
joined the controller under the same AP profile.

Integer32r/w

Constraints:
range: 0-7

.1.3.6.1.4.1.9.9.513.1.16.4.1.2

cLApProfileQosMapExceptionRowStatus

This object specifies the row to be added or
deleted in this table.

cLApPacketCaptureProfileName

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.9.9.513.1.16.4.1.3

cLApPacketCaptureProfileTable

table

.1.3.6.1.4.1.9.9.513.1.17.1 · 1 row entry · 23 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApPacketCaptureProfileTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApPacketCaptureProfileTable'

This table provides the information about the packet capture
parameters for the 802.11 LWAPP Access Points.
Rows are added to this table whenever, new profiles
are added to this controller, and rows are deleted
whenever profiles gets deleted from the controller.

cLApPacketCaptureProfileEntry row .1.3.6.1.4.1.9.9.513.1.17.1.1

Each entry in this table provides information about the packet
capture profile configured on the controller.

Indexes

Column Syntax OID

cLApPacketCaptureProfileName

This object represents the profile name for
ap packet capture profile. The parameters of
packet capture profile are used while capturing packets
on the Access Point for the specified wireless client.

OctetString

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.17.1.1.1

cLApPacketCaptureProfileRowStatus

Used to add or delete an entry in this table.

cLApPacketCaptureProfileBufferSize

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.9.9.513.1.17.1.1.2

This object specifies the size of the buffer Access Point
should use to copy the captured packets for client and dump
it to the FTP server.

kilobytesUnsigned32r/w

Constraints:
range: 1024-4096

.1.3.6.1.4.1.9.9.513.1.17.1.1.3

cLApPacketCaptureProfileDuration

This object specifies the duration for which the Access Point
should capture packets for specified client.

MinutesUnsigned32r/w

Constraints:
range: 1-60

.1.3.6.1.4.1.9.9.513.1.17.1.1.4

cLApPacketCaptureProfileTruncation

This object specifies the length of the packet after
truncation while capturing packets on the Access Point.
Default value is 0 which indictaes captured packet should
contain the full payload length.

bytesUnsigned32r/w

Constraints:
range: 0-1500

.1.3.6.1.4.1.9.9.513.1.17.1.1.5

cLApPacketCaptureProfileFtpServerAddressType

This object specifies the type of the ftp server
IP Address made available through
cLApPacketCaptureProfileEntry.

cLApPacketCaptureProfileFtpServerAddress

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.9.9.513.1.17.1.1.6

This object specifies the IP Address of the
FTP server. Access Point will dump the captured packets
to a file in this ftp server.

cLApPacketCaptureProfileFtpServerPath

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.17.1.1.7

This object specifies the directory path in the
ftp server for storing the file which contains the
captured packets in the Access Point.

cLApPacketCaptureProfileFtpUsername

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.17.1.1.8

This object specifies the username to login into
the ftp server in order to transfer the captured
packets from the Access Point.

cLApPacketCaptureProfileFtpPassword

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.17.1.1.9

This object specifies the password to login into
the ftp server in order to transfer the captured
packets from the Access Point.

cLApPacketCaptureProfileClassifierArp

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.17.1.1.10

This object specifies the filters for ARP packets
while capturing packets on the Access Point.
A value of 'true' indicates ARP packets should be captured.
A value of 'false' indicates ARP packets shouldn't be captured.

cLApPacketCaptureProfileClassifierBroadcast

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.17.1.1.11

This object specifies the filters for 802.11 Broadcast
packets, while capturing packets on the Access Point.
A value of 'true' indicates Broadcast packets should be
captured.
A value of 'false' indicates Broadcast packe…

cLApPacketCaptureProfileClassifierControl

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.17.1.1.12

This object specifies the filters for 802.11 control packets,
while capturing packets on the Access Point under AP Profile
which is making use of this packet capture profile.

A value of 'true' indicates …

cLApPacketCaptureProfileClassifierData

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.17.1.1.13

This object specifies the filters for 802.11 Data packets,
while capturing packets on the Access Point under AP Profile
which is making use of this packet capture profile.

A value of 'true' indicates 802…

cLApPacketCaptureProfileClassifierDot1x

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.17.1.1.14

This object specifies the filters for 802.11 Dot1x packets,
while capturing packets on the Access Point under AP Profile
which is making use of this packet capture profile.
A value of 'true' indicates 802.11 Dot1x pack…

cLApPacketCaptureProfileClassifierIapp

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.17.1.1.15

This object specifies the filters for 802.11 IAPP packets,
while capturing packets on the Access Point under AP Profile
which is making use of this packet capture profile.
A value of 'true' indicates IAPP packets should…

cLApPacketCaptureProfileClassifierIp

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.17.1.1.16

This object specifies the filters for IP packets,
while capturing packets on the Access Point.
A value of 'true' indicates IP packets should be captured.
A value of 'false' indicates IP packets should not be captured.

cLApPacketCaptureProfileClassifierManagement

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.17.1.1.17

This object specifies the filters for 802.11 Management
packets, while capturing packets on the Access Point. A value
of 'true' indicates 802.11 Management packets should be
captured.
A value of 'false' indicates 802.11…

cLApPacketCaptureProfileClassifierMulticast

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.17.1.1.18

This object specifies the filters for 802.11 Multicast
packets, while capturing packets on the Access Point.
A value of 'true' indicates Multicast packets should be
captured.
A value of 'false' indicates Multicast packe…

cLApPacketCaptureProfileClassifierTcp

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.17.1.1.19

This object specifies the filters for TCP packets,
while capturing packets on the Access Point.
Value of 'true' indicates IP packets should be captured.
Value of 'false' indicates IP packets should not be captured.

cLApPacketCaptureProfileClassifierUdp

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.17.1.1.20

cLApPacketCaptureProfileClassifierTcpPort

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.17.1.1.21

This object specifies the filter value port number for TCP
packets, while capturing packets on the Access Point.
Default value is 0 which indicates all TCP packets should
be captured.

Unsigned32r/w

Constraints:
range: 0-65535

.1.3.6.1.4.1.9.9.513.1.17.1.1.22

cLApPacketCaptureProfileClassifierUdpPort

This object specifies the filter value port number for UDP
packets, while capturing packets on the Access Point under AP
Profile which is making use of this packet capture profile.
Default value is 0 which indicates al…

Unsigned32r/w

Constraints:
range: 0-65535

.1.3.6.1.4.1.9.9.513.1.17.1.1.23

cLApPacketCaptureClientTable

table

.1.3.6.1.4.1.9.9.513.1.17.2 · 1 row entry · 6 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApPacketCaptureClientTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApPacketCaptureClientTable'

This table provides information about the status of
packet capture already in progress on per Client basis.
Rows are added to this table whenever, packet capture is
started for a new client, and rows are deleted whenever 
packet capture gets stopped for a particular Client.

cLApPacketCaptureClientEntry row .1.3.6.1.4.1.9.9.513.1.17.2.1

Each entry in this table provides information about packet
capture session currently going on for a client on 802.11
LWAPP Access Point that has joined the controller.

Indexes

cLApPacketCaptureClientDeviceMac

Column Syntax OID

cLApPacketCaptureClientDeviceMac

This object represents the mac address of the client for
which packet capture should be started on the Access Point.
Access Point will check for this mac address
while capturing packets.

cLApPacketCaptureClientApMacAddress

Type Constraints:
range: 6

Description:

.1.3.6.1.4.1.9.9.513.1.17.2.1.1

This object represents the base radio mac address
of the Access Point on which packet capture should
be started. This will be used only in case of static mode
but, it is mandatory to populate this in static mode as well.

SNMPv2-TCMacAddressr/w

Type Constraints:
range: 6

Description:

.1.3.6.1.4.1.9.9.513.1.17.2.1.2

cLApPacketCaptureClientAutoMode

This object specifies the mode for packet capture.
A value of 'true' indicates packet capture should be started
in auto mode, which means capture will be started on the
Access Point on which device is currently connecte…

cLApPacketCaptureClientStartStop

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.17.2.1.3

This object specifies the trigger to start or stop
packet capture for the client. A value of '1'
indicates packet capture should be started. A value
of '2' indicates packet capture should be stopped.

Enumerationr/w

Enumerated Values:

1	idle
2	start
3	stop

.1.3.6.1.4.1.9.9.513.1.17.2.1.4

cLApPacketCaptureClientSiteName

This object represents the name of the site on which the
specific device or the Access Point is present.

OctetString

Constraints:
range: 0-32

.1.3.6.1.4.1.9.9.513.1.17.2.1.5

cLApPacketCaptureClientRowStatus

This oject specifies to the addition or deletion of an
entry in this table. When an entry is added, packet
capture will be started for the specified device.
When an entry is deleted, packet capture will be stopped
for …

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.9.9.513.1.17.2.1.6

cLApPacketCaptureApTable

table

.1.3.6.1.4.1.9.9.513.1.17.3 · 1 row entry · 3 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLApPacketCaptureApTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLApPacketCaptureApTable'

This table provides information about the status of
packet capture already in progress on a per AP, per Client 
basis. Rows are added to this table whenever, packet capture 
is started for a client on a new AP, and rows are deleted 
whenever packet capture gets stopped on a particular AP.

cLApPacketCaptureApEntry row .1.3.6.1.4.1.9.9.513.1.17.3.1

Each entry in this table provides information about status of
packet capture already in progress on the specific AP.

Indexes

cLApPacketCaptureApDeviceMac

Column Syntax OID

This object specifies the mac address of the device for
which packet capture was started on the Access Point.
Access Point will check for this mac address
while capturing packets.

cLApPacketCaptureApMacAddress

Type Constraints:
range: 6

Description:

.1.3.6.1.4.1.9.9.513.1.17.3.1.1

This object specifies the base radio mac address of
the Access Point on which packet capture was started for
the specific device.

cLApPacketCaptureApStatus

Type Constraints:
range: 6

Description:

.1.3.6.1.4.1.9.9.513.1.17.3.1.2

This object specifies the status of the packet capture.
A value of 'true' indicates packet capture has been started
for the specified device on the specific Access Point,
A value of 'false' indicates packet capture is n…

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.17.3.1.3

cLAPNtpInfoTable

table

.1.3.6.1.4.1.9.9.513.1.18.1 · 1 row entry · 7 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLAPNtpInfoTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLAPNtpInfoTable'

This table represents collection of
NTP-Server information received from AP.

cLAPNtpInfoEntry row .1.3.6.1.4.1.9.9.513.1.18.1.1

Each entry in cLAPNtpInfoTable corresponds
NTP-server information for a particular AP.

Indexes

Column Syntax OID

cLAPNtpInfoState

This object specifies whether
NTP service is enabled or disabled at AP.
A value 'true' means NTP server is running at AP.
A value 'false' means NTP server is not running at AP

CISCO-LWAPP-TC-MIBCLApNtpStatus

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.18.1.1.1

cLApNtpInfoStatus

This object specifies the NTP server
status for AP

Type Values:

1	notValid
2	none
3	unreachable
4	synched
5	notSynched
6	waitSynch
7	authFail
8	notSuitable
9	unknown

.1.3.6.1.4.1.9.9.513.1.18.1.1.2

cLAPNtpInfoStratum

This object specifies NTP server stratum
for AP.
The object value is only applicable when
cLAPNtpInfoState is 'true' and cLApNtpInfoStatus
is other than none.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.18.1.1.3

cLAPNtpInfoLastSync

This object specifies AP last synced time with
NTP server in seconds.
The object value is only applicable when cLAPNtpInfoState
is 'true' and cLApNtpInfoStatus is other than none.

INET-ADDRESS-MIBInetAddressType

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.9.9.513.1.18.1.1.4

cLAPNtpInfoOffset

This object specifies NTP server offset
in micro-seconds for AP.
The object value is only applicable when
cLAPNtpInfoState is 'true' and cLApNtpInfoStatus
is other than none.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.9.9.513.1.18.1.1.5

cLAPNtpInfoIPAddressType

This object specifies the NTP server
IP address type (ipv4 or ipv6) currently configured at AP.
The object value is only applicable when
cLAPNtpInfoState is 'true' and
cLApNtpInfoStatus is other than none.

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.9.9.513.1.18.1.1.6

cLAPNtpInfoIPAddress

This object specifies the NTP server
IP address currently configured at AP.
The object value is only applicable when
cLAPNtpInfoState is 'true' and
cLApNtpInfoStatus is other than none.

INET-ADDRESS-MIBInetAddress

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.513.1.18.1.1.7

cLAp11axRadioConfigTable

table

.1.3.6.1.4.1.9.9.513.1.21.1 · 1 row entry · 8 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cLAp11axRadioConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-LWAPP-AP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-LWAPP-AP-MIB::cLAp11axRadioConfigTable'

This table represents the radio configuration
of 11ax Access Points

cLAp11axRadioConfigEntry row .1.3.6.1.4.1.9.9.513.1.21.1.1

Each entry in cLAp11axRadioConfigTable
corresponds to an 11ax Access Point radio configuration.

Indexes

Column Syntax OID

cLAp11axDualRadioCapable

This object represents whether radio is dual radio capable or
not.
A value of 'true' indicates the radio is dual mode capable.
A value of 'false' indicates the radio is not dual mode capable.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.21.1.1.1

cLAp11axRadioFRACapable

This object represents whether radio is FRA capable or not.
A value of 'true' indicates the radio is FRA Capable.
A value of 'false' indicates the radio is not FRA capable.

cLAp11axDualRadioOperation

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.21.1.1.2

This object specifies dual radio mode operation of
the slot.
auto - Dual radio mode is automatic.
manual - Dual radio mode is configurable manually.
none - Radio is not dual radio mode capable.

Enumerationr/w

Enumerated Values:

1	auto
2	manual
3	none

.1.3.6.1.4.1.9.9.513.1.21.1.1.3

cLAp11axDualRadioMode

This object specifies dual radio mode status of radio
enabled - Dual radio mode is enabled.
disabled- Dual radio mode is disabled.
none - Radio is not dual radio mode capable.

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
3	none

.1.3.6.1.4.1.9.9.513.1.21.1.1.4

cLAp11axRadioRoleOperation

This object specifies the radio role operation
of the slot.
auto - Radio role assignment is automatic.
manual - Radio role assignment is manual.
none - Radio role assignment is neither manual nor automatic.

Enumerationr/w

Enumerated Values:

1	auto
2	manual
3	none

.1.3.6.1.4.1.9.9.513.1.21.1.1.5

cLAp11axRadioRole

This object specifies the role for the slot.
local - The means the slot is capable of serving clients.
monitor - The slot does not serves client, only monitors.
none - The slot is neither client serving nor monitor.

Enumerationr/w

Enumerated Values:

1	clientserving
2	monitor
3	none

.1.3.6.1.4.1.9.9.513.1.21.1.1.6

cLAp11axObssPdCapable

This object represents whether the radio is 802.11ax OBSS PD capable
or not.
A value of 'true' indicates the radio is OBSS PD capable.
A value of 'false' indicates the radio is not OBSS PD capable.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.513.1.21.1.1.7

cLAp11axObssPdSrgCapable

This object represents whether the radio is 802.11ax SRG OBSS PD capable
or not.
A value of 'true' indicates the radio is SRG OBSS PD capable.
A value of 'false' indicates the radio is not SRG OBSS PD capable.