cLApUsbSerialNumber
CISCO-LWAPP-AP-MIB ·
.1.3.6.1.4.1.9.9.513.1.1.1.1.114
Object
column
OctetString
This object specifies serial number of USB module on the AP.
Context
- MIB
- CISCO-LWAPP-AP-MIB
- OID
.1.3.6.1.4.1.9.9.513.1.1.1.1.114- Type
- column
- Access
- readonly
- Status
- current
- Parent
- cLApEntry
- Table
- cLApTable
- Siblings
- 112
Syntax
OctetString
Values & Constraints
Object Constraints
range: 0-12
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cLApSysMacAddress This object represents the radio MAC address
common to the dot11 interfaces of the AP
and uniquely identifies an entry in this table. | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.9.9.513.1.1.1.1.1 |
| cLApPrimaryControllerAddressType This object specifies the type of the primary
controller's address made available through
cLApPrimaryControllerAddress. | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.9.9.513.1.1.1.1.10 |
| cLApModeClear This object specifies to clear the modes like 'Sniffer',
'Monitor' which is not inherited from tag configuration on
controller. Once cleared, AP may reboot and move to the AP mode… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.103 |
| cLApSiteTagName This object specifies the site tag name of the AP | column | OctetString | .1.3.6.1.4.1.9.9.513.1.1.1.1.104 |
| cLApRfTagName This object specifies the RF tag name of the AP | column | OctetString | .1.3.6.1.4.1.9.9.513.1.1.1.1.105 |
| cLApPolicyTagName This object specifies the policy tag name of the AP. | column | OctetString | .1.3.6.1.4.1.9.9.513.1.1.1.1.106 |
| cLApTagSource This object specifies the source of the tag. | column | Enumeration | .1.3.6.1.4.1.9.9.513.1.1.1.1.107 |
| cLApUsbModuleName This object specifies module name of USB module
On the AP. | column | OctetString | .1.3.6.1.4.1.9.9.513.1.1.1.1.108 |
| cLApUsbModuleState This object specifies whether USB module detected or not
detected on the AP. | column | OctetString | .1.3.6.1.4.1.9.9.513.1.1.1.1.109 |
| cLApPrimaryControllerAddress This object specifies the address of the primary
controller that the APs will join. | column | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.9.9.513.1.1.1.1.11 |
| cLApUsbModuleProductId This object specifies product Id of USB module on the AP. | column | OctetString | .1.3.6.1.4.1.9.9.513.1.1.1.1.110 |
| cLApUsbDescription This object specifies description of USB module on the AP. | column | OctetString | .1.3.6.1.4.1.9.9.513.1.1.1.1.111 |
| cLApUsbStateInfo This object specifies State(enable/disable) of USB module
on the AP. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.112 |
| cLApUsbOverride This object specifies Override(enable/disable) of USB module
on the AP. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.113 |
| cLApUsbMaxPower This object specifies max power given to USB module
on the AP. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.115 |
| cLApLagConfigStatus This object specifies the configured LAG status(enable/disable)
on the AP. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.116 |
| cLApMonitorModeOptStatus This object specifies the Monitor Mode optimization support(enable/disable)
on the AP. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.117 |
| cLApFilterName This object specifies the Filter name applied on this AP | column | OctetString | .1.3.6.1.4.1.9.9.513.1.1.1.1.118 |
| cLApSecondaryControllerAddressType This object specifies the type of the secondary
controller's address made available through
cLApSecondaryControllerAddress. | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.9.9.513.1.1.1.1.12 |
| cLApSecondaryControllerAddress This object specifies the address of the secondary
controller that the APs will join. | column | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.9.9.513.1.1.1.1.13 |
| cLApTertiaryControllerAddressType This object specifies the type of the tertiary
controller's address made available through
cLApTertiaryControllerAddress. | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.9.9.513.1.1.1.1.14 |
| cLApTertiaryControllerAddress This object specifies the address of the tertiary
controller that the APs will join. | column | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.9.9.513.1.1.1.1.15 |
| cLApLastRebootReason This object represents the reason for the last
reboot of the AP.
none - ap reported a reboot reason code
unknown to the co… | column | Enumeration | .1.3.6.1.4.1.9.9.513.1.1.1.1.16 |
| cLApEncryptionEnable This object specifies whether encyrption between
controller and AP is enabled or not. Encryption
can only be enabled if ESM card in controller is
pluged in.
A valu… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.18 |
| cLApFailoverPriority This object specifies the AP failover priority
for an AP. If a higher priority AP wishes to join
the controller, it will be given preference over
a join request from a lower pri… | column | Enumeration | .1.3.6.1.4.1.9.9.513.1.1.1.1.19 |
| cLApIfMacAddress This object represents the Ethernet MAC address of
the AP. | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.9.9.513.1.1.1.1.2 |
| cLApPowerStatus This object represents the power status of the AP
low - The AP is drawing low power from
Ethernet
fifteendotfour - The AP is drawing 15.4 watts fr… | column | Enumeration | .1.3.6.1.4.1.9.9.513.1.1.1.1.20 |
| cLApTelnetEnable This object specifies whether telnet session
can be established to the AP.
A value of 'true' indicates an telnet session
can be established to the AP.
… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.21 |
| cLApSshEnable This object specifies whether SSH session
can be established to the AP.
A value of 'true' indicates an SSH session
can be established to the AP.
A … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.22 |
| cLApPreStdStateEnabled This object specifies whether the pre-standard state
of the AP is enabled or disabled.
A value of 'true' indicates that the pre-standard state
of the AP is enabled,… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.23 |
| cLApPwrInjectorStateEnabled This object specifies whether the power injector state
of the AP is enabled or disabled.
A value of 'true' indicates that the power injector state
of the AP is enab… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.24 |
| cLApPwrInjectorSelection This object specifies the power injector selection
value of the AP.
'unknown' - is returned if
'cLApPwrInjectorStateEnabled'is set to false.
'installed' - … | column | Enumeration | .1.3.6.1.4.1.9.9.513.1.1.1.1.25 |
| cLApPwrInjectorSwMacAddr This object specifies the MAC address of the
switch port that has a power Injector and is
valid only when the 'cLApPwrInjectorSelection'
is in 'installed' mode.
if SET to 00:00:… | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.9.9.513.1.1.1.1.26 |
| cLApWipsEnable deprecated This object represents if this AP is used
as WIPS AP.
A value of 'true' indicates that this AP is
a WIPS AP.
A value of 'false' indicates that this AP is
not a WIPS AP. This appli… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.27 |
| cLApMonitorModeOptimization This object specifies the monitor mode optimization
on this device.
all - All optimization is enabled
tracking - Tracking is optimized
wips - WIPS optimizat… | column | Enumeration | .1.3.6.1.4.1.9.9.513.1.1.1.1.28 |
| cLApDomainName This object specifies the domain, to which the AP belongs.
This attribute can be configured only if the static IP
option is turned on in the AP. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.513.1.1.1.1.29 |
| cLApMaxNumberOfDot11Slots This object represents the maximum number of
802.11 radio interface slots in this AP. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.3 |
| cLApNameServerAddressType This object specifies the type of the IP address of the
name server, made available through cLApNameServerAddress. | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.9.9.513.1.1.1.1.30 |
| cLApNameServerAddress This object specifies the IP Address of the name server.
This attribute can be configured only if the static IP
option is turned on in the AP. | column | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.9.9.513.1.1.1.1.31 |
| cLApAMSDUEnable This object specifies the AMSDU status.
A value of 'true' indicates AMSDU is enabled.
A value of 'false' indicates AMSDU is disabled. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.32 |
| cLApEncryptionSupported This object specifies whether AP Supports
DTLS encryption.
A value of 'true' indicates encryption is supported.
A value of 'false' indicates encryption is not sup… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.33 |
| cLApRogueDetectionEnabled This object specifies whether Rogue Detection
is enabled in this AP.
A value of 'true' indicates rogue detection is enabled.
A value of 'false' indicates rogue de… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.34 |
| cLApTcpMss This object specifies the TCP Maximum Segment Size
for this AP.
Permissible value are between 536 and 1363. This will
also enable the TCP MSS flag for this AP.
Value of 0 will dis… | column | Integer32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.35 |
| cLApDataEncryptionStatus This object represents the data encryption
status of AP.
A value of 'true' indicates data is encrypted between
AP and WLC.
A value of… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.36 |
| cLApNsiKey This object represents the network spectrum interface key
used when the AP is in spectrum expert Only monitor mode
(SOMM).This object returns a non-zero value only when the
AP is… | column | OctetString | .1.3.6.1.4.1.9.9.513.1.1.1.1.37 |
| cLApAdminStatus This object specifies the admin state of the AP,
A value of 'true' indicates AP admin status is up.
A value of 'false' indicates AP admin status is down. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.38 |
| cLApPortNumber This object represents the port number on which
the AP's traffic is coming through. | column | INET-ADDRESS-MIBInetPortNumber | .1.3.6.1.4.1.9.9.513.1.1.1.1.39 |
| cLApEntPhysicalIndex This object provides the index value in the
entPhysicalEntry corresponding to this AP. | column | ENTITY-MIBPhysicalIndex | .1.3.6.1.4.1.9.9.513.1.1.1.1.4 |
| cLApRetransmitCount This object specifies the retransmission count for the access
point control packet.This value specifies the number of packets
retransmitted after which the Access Point falls back… | column | retries SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.40 |
| cLApRetransmitTimeout This object specifies the retransmission timeout for the access
point control packet. This value specifies the timeout for each
retransmission, during the fallback of access point… | column | seconds SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.41 |
| cLApVenueConfigVenueGroup This object specifies the venue group
for this WLAN. | column | Enumeration | .1.3.6.1.4.1.9.9.513.1.1.1.1.42 |
| cLApVenueConfigVenueType This object specifies the venue type within
a particular venue group,for this WLAN.
The venue group-venue type relationship is per
the following table:
Venue Group Venue Type Code… | column | Enumeration | .1.3.6.1.4.1.9.9.513.1.1.1.1.43 |
| cLApVenueConfigVenueName This object specifies the venue name defined for this AP
group. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.513.1.1.1.1.44 |
| cLApVenueConfigLanguage This object specifies the language defined for this AP group. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.513.1.1.1.1.45 |
| cLApLEDState This object specifies whether the LED state of this access
point should be enabled or disabled.
A value of 'true' indicates LED status is enabled.
A value of 'false' indicates LED… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.46 |
| cLApTrunkVlan This object specifies the trunk VLAN ID
assigned to this AP's ethernet interface.
When a non-zero value is assigned for this
Object, the management packets will be
tagged with th… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.47 |
| cLApTrunkVlanStatus This object specifies whether the trunk VLAN ID
assigned to this AP's is effective. If the AP is unable
to route the management frames through the trunk
vlan, it will revert back … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.48 |
| cLApLocation This object specifies the user specified location of this AP.
While configuring AP, user should specify a location for
the AP so that its easy to figure out for some one where
the… | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.513.1.1.1.1.49 |
| cLApName This object specifies the administrative name
assigned to the AP by the user. If an AP is not configured,
its factory default name will be ap:<last three byte
of MACAddress> eg.… | column | OctetString | .1.3.6.1.4.1.9.9.513.1.1.1.1.5 |
| cLApSubMode This object specifies the sub mode of the AP.
The option 'wips' applies only when the
AP is in local, flexConnect or monitor mode.
This 'pppoe' options apply only when the
AP is… | column | Enumeration | .1.3.6.1.4.1.9.9.513.1.1.1.1.50 |
| cLApAssocCount This object specifies the association count for the access
point. This counter includes both successful and failed
associate attempts, but does NOT include the re-associate
atte… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.51 |
| cLApAssocFailResourceCount This object specifies the association failure count for the
access point due to the resource limits, i.e. the max clients
of the WLAN/Radio is reached. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.52 |
| cLApRealTimeStatsModeEnabled This object specifies whether current stats mode is
'realtime'. There are two stats-mode, realtime and normal which
specifies the stats-timer range to be 10-180 sec and 2-5 sec
e… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.53 |
| cLApAssociatedClientCount This object represents the associated client number for the
access point. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.54 |
| cLApMemoryCurrentUsage This object represents the percent of current memory usage
of the access point. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.55 |
| cLApMemoryAverageUsage This object represents the percent of average memory usage
of the access point. The statistics window is defined by
clsSysStatisticsInterval. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.56 |
| cLApCpuCurrentUsage This object represents the percent of current CPU usage
of the access point. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.57 |
| cLApCpuAverageUsage This object represents the percent of average CPU usage
of the access point. The statistics window is defined by
clsSysStatisticsInterval. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.58 |
| cLApUpgradeFromVersion This object represents the AP image upgrade
from version. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.513.1.1.1.1.59 |
| cLApUpTime This object represents the time in hundredths
of a second since the last time the AP rebooted. | column | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.9.9.513.1.1.1.1.6 |
| cLApUpgradeToVersion This object represents the AP image upgrade
to version. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.513.1.1.1.1.60 |
| cLApUpgradeFailureCause This object represents the cause of the
AP image upgrade failure. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.513.1.1.1.1.61 |
| cLApMaxClientLimitNumberTrap This object represents the max client limit number. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.62 |
| cLApMaxClientLimitCause This object represents the cause of the
max client limit reach. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.513.1.1.1.1.63 |
| cLApMaxClientLimitSet This object represents whether this event is
raised or cleared.
A value of 'true' indicates this event is set.
A value of 'false' indicates this even is cleared. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.64 |
| cLApFloorLabel This object specifies the floor label for the Access Point. | column | CISCO-TCUnsigned64 | .1.3.6.1.4.1.9.9.513.1.1.1.1.65 |
| cLApConnectCount deprecated This object represents the Count of AP's that are connected
to the Controller. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.66 |
| cLApReassocSuccCount This object represents the successful re-association
count for the Access Point. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.67 |
| cLApReassocFailCount This object represents the failed re-association
count for the Access Point. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.68 |
| cLAdjChannelRogueEnabled deprecated This object specifies if rogue AP
detection and removed Traps need to be sent.
A value of 'true' indicates adjacent rogue detection
is enabled.
A value of 'false' indicates adjace… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.69 |
| cLLwappUpTime This object represents the time in hundredths
of a second since the last time the AP joined
the controller. | column | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.9.9.513.1.1.1.1.7 |
| cLApAssocFailCountByRate This object represents the failed association
count for the access point caused by rate mismatch. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.70 |
| cLApAbnormalOfflineCount This object represents the abnormal offline count for the
access point. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.71 |
| cLApActiveClientCount This object represents the active client number for the access
point. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.72 |
| cLApAssocFailCountForRssiLow This object represents the failed association
count for the access point caused by RSSI low. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.73 |
| cLApSysNetId This object specifies the ApSysNetId which is the numeric
string to identify the system information like ApName. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.513.1.1.1.1.74 |
| cLApAssocFailTimes This object represents the counts of client failed association
to the access point. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.75 |
| cLApAntennaBandMode This object specifies the mode of antenna band.
notApplicable - will return for unsuppported APs.
single - configure the AP to use single band for antenna.
dual - configure the … | column | Enumeration | .1.3.6.1.4.1.9.9.513.1.1.1.1.76 |
| cLApHeartBeatRspAvgTime This object represents the average interval between sending
the echo request and receiving the echo response in AP. | column | milliseconds Integer32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.77 |
| cLApEchoRequestCount This object represents the echo request packet
count sent from AP to access controller. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.78 |
| cLApEchoResponseLossCount This object represents the echo response loss
count from access controller to AP. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.79 |
| cLLwappJoinTakenTime This object represents the time taken in hundredths
of a second for the AP to join the controller. This
could be a significant value in Mesh environments. | column | SNMPv2-SMITimeTicks | .1.3.6.1.4.1.9.9.513.1.1.1.1.8 |
| cLApModuleInserted This object represents the type of the module
inserted in to the AP. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.513.1.1.1.1.80 |
| cLApEnableModule This object specifies the status of the external
module .
A value of 'true' indicates module is enabled.
A value of 'false' indicates module is disabled. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.81 |
| cLApIsUniversal This object represents the if the AP is
universal AP.
A value of 'true' indicates AP is universal SKU based AP.
A value of 'false' indicates AP is non-Universal SKU AP. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.82 |
| cLApUniversalPrimeStatus This object represents the method of Priming
of the Universal AP. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.513.1.1.1.1.83 |
| cLApIsMaster This object represents whether the flex AP is a
master AP. This applies only to FlexExpress controllers.
A value of 'true' indicates AP is a master AP.
A value of 'false' indica… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.84 |
| cLApBleFWDownloadStatus This object represents the list of APs in which BLE
firmware download is in progress.
A value of 'true' indicates BLE download is in progress.
A value of 'false' indicates BLE dow… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.85 |
| cLApDot11XorDartConnectorStatus This object represents the XOR dart connector status. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.513.1.1.1.1.86 |
| cLApCtsSxpDefaultPassword This object specifies the SXP(Security Group Tag Exchange
Protocol) default password. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.9.513.1.1.1.1.87 |
| cLApCtsSxpState This object specifies SXP(Security Group Tag Exchange
Protocol) state.
A value of 'true' indicates sxp state is enabled.
A value of 'false' indicates sxp state is disabled. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.88 |
| cLApCtsSxpMode This object specifies SXP(Security Group Tag Exchange
Protocol) mode.
A value of 'true' indicates sxp mode is enabled.
A value of 'false' indicates sxp mode is disabled. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.89 |
| cLApMaxNumberOfEthernetSlots This object represents the maximum number of
Ethernet slots in this AP. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.9 |
| cLApCtsSxpListenerMinHoldtime This object specifies SXP(Security Group Tag Exchange
Protocol) listener hold time.
It specifies the global maximum hold-time for
SXP connections in 'listener' mode.
… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.90 |
| cLApCtsSxpListenerMaxHoldtime This object specifies SXP(Security Group Tag Exchange
Protocol) listener hold time.
It specifies the global maximum hold-time for
SXP connections in 'listener' mode.
… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.91 |
| cLApCtsSxpReconcilePeriod This object specifies SXP(Security Group Tag Exchange
Protocol) reconcile period. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.92 |
| cLApCtsSxpRetryPeriod This object specifies SXP(Security Group Tag Exchange
Protocol) retry period. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.93 |
| cLApCtsSxpSpeakerHoldTime This object specifies SXP(Security Group Tag Exchange
Protocol) speaker hold time. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.94 |
| cLApCtsSxpSpeakerKeepAlive This object specifies SXP(Security Group Tag Exchange
Protocol) speaker keep alive time. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.9.9.513.1.1.1.1.95 |
| cLApCtsInlineTagStatus This object specifies Cisco Trustsec inline tagging
is enabled/disabled.
A value 'true' indicates inline tag is enabled.
A value 'false' indicates inline tag is disabled. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.96 |
| cLApCtsSgaclStatus This object specifies Cisco Trustsec Security Group Tag
ACL enforcement status.
A value 'true' indicates SgACL enforcement is enabled
A value 'false' indicates SgACL enforcement… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.97 |
| cLApCtsOverrideStatus This object specifies Cisco Trustsec AP Override status.
A value of 'true' indicates CTS AP Override is enabled.
A value of 'false' indicates CTS AP Override is disabled. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.513.1.1.1.1.98 |