cLApCtsSxpState

CISCO-LWAPP-AP-MIB · .1.3.6.1.4.1.9.9.513.1.1.1.1.88
MIB view Table view

Object

column r/w SNMPv2-TCTruthValue 
This object specifies SXP(Security Group Tag Exchange
Protocol) state.
 A value of 'true' indicates sxp state is enabled.
 A value of 'false' indicates sxp state is disabled.

Context

MIB
CISCO-LWAPP-AP-MIB
OID
.1.3.6.1.4.1.9.9.513.1.1.1.1.88
Type
column
Access
readwrite
Status
current
Parent
cLApEntry
Table
cLApTable
Siblings
112

Syntax

SNMPv2-TCTruthValue
Source
SNMPv2-TCTruthValue
Base type
Enumeration

Values & Constraints

Type Values
1true
2false

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
cLApSysMacAddress
This object represents the radio MAC address common to the dot11 interfaces of the AP and uniquely identifies an entry in this table.
columnSNMPv2-TCMacAddress.1.3.6.1.4.1.9.9.513.1.1.1.1.1
cLApPrimaryControllerAddressType
This object specifies the type of the primary controller's address made available through cLApPrimaryControllerAddress.
columnINET-ADDRESS-MIBInetAddressType.1.3.6.1.4.1.9.9.513.1.1.1.1.10
cLApModeClear
This object specifies to clear the modes like 'Sniffer', 'Monitor' which is not inherited from tag configuration on controller. Once cleared, AP may reboot and move to the AP mode…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.103
cLApSiteTagName
This object specifies the site tag name of the AP
columnOctetString.1.3.6.1.4.1.9.9.513.1.1.1.1.104
cLApRfTagName
This object specifies the RF tag name of the AP
columnOctetString.1.3.6.1.4.1.9.9.513.1.1.1.1.105
cLApPolicyTagName
This object specifies the policy tag name of the AP.
columnOctetString.1.3.6.1.4.1.9.9.513.1.1.1.1.106
cLApTagSource
This object specifies the source of the tag.
columnEnumeration.1.3.6.1.4.1.9.9.513.1.1.1.1.107
cLApUsbModuleName
This object specifies module name of USB module On the AP.
columnOctetString.1.3.6.1.4.1.9.9.513.1.1.1.1.108
cLApUsbModuleState
This object specifies whether USB module detected or not detected on the AP.
columnOctetString.1.3.6.1.4.1.9.9.513.1.1.1.1.109
cLApPrimaryControllerAddress
This object specifies the address of the primary controller that the APs will join.
columnINET-ADDRESS-MIBInetAddress.1.3.6.1.4.1.9.9.513.1.1.1.1.11
cLApUsbModuleProductId
This object specifies product Id of USB module on the AP.
columnOctetString.1.3.6.1.4.1.9.9.513.1.1.1.1.110
cLApUsbDescription
This object specifies description of USB module on the AP.
columnOctetString.1.3.6.1.4.1.9.9.513.1.1.1.1.111
cLApUsbStateInfo
This object specifies State(enable/disable) of USB module on the AP.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.112
cLApUsbOverride
This object specifies Override(enable/disable) of USB module on the AP.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.113
cLApUsbSerialNumber
This object specifies serial number of USB module on the AP.
columnOctetString.1.3.6.1.4.1.9.9.513.1.1.1.1.114
cLApUsbMaxPower
This object specifies max power given to USB module on the AP.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.115
cLApLagConfigStatus
This object specifies the configured LAG status(enable/disable) on the AP.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.116
cLApMonitorModeOptStatus
This object specifies the Monitor Mode optimization support(enable/disable) on the AP.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.117
cLApFilterName
This object specifies the Filter name applied on this AP
columnOctetString.1.3.6.1.4.1.9.9.513.1.1.1.1.118
cLApSecondaryControllerAddressType
This object specifies the type of the secondary controller's address made available through cLApSecondaryControllerAddress.
columnINET-ADDRESS-MIBInetAddressType.1.3.6.1.4.1.9.9.513.1.1.1.1.12
cLApSecondaryControllerAddress
This object specifies the address of the secondary controller that the APs will join.
columnINET-ADDRESS-MIBInetAddress.1.3.6.1.4.1.9.9.513.1.1.1.1.13
cLApTertiaryControllerAddressType
This object specifies the type of the tertiary controller's address made available through cLApTertiaryControllerAddress.
columnINET-ADDRESS-MIBInetAddressType.1.3.6.1.4.1.9.9.513.1.1.1.1.14
cLApTertiaryControllerAddress
This object specifies the address of the tertiary controller that the APs will join.
columnINET-ADDRESS-MIBInetAddress.1.3.6.1.4.1.9.9.513.1.1.1.1.15
cLApLastRebootReason
This object represents the reason for the last reboot of the AP. none - ap reported a reboot reason code unknown to the co…
columnEnumeration.1.3.6.1.4.1.9.9.513.1.1.1.1.16
cLApEncryptionEnable
This object specifies whether encyrption between controller and AP is enabled or not. Encryption can only be enabled if ESM card in controller is pluged in. A valu…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.18
cLApFailoverPriority
This object specifies the AP failover priority for an AP. If a higher priority AP wishes to join the controller, it will be given preference over a join request from a lower pri…
columnEnumeration.1.3.6.1.4.1.9.9.513.1.1.1.1.19
cLApIfMacAddress
This object represents the Ethernet MAC address of the AP.
columnSNMPv2-TCMacAddress.1.3.6.1.4.1.9.9.513.1.1.1.1.2
cLApPowerStatus
This object represents the power status of the AP low - The AP is drawing low power from Ethernet fifteendotfour - The AP is drawing 15.4 watts fr…
columnEnumeration.1.3.6.1.4.1.9.9.513.1.1.1.1.20
cLApTelnetEnable
This object specifies whether telnet session can be established to the AP. A value of 'true' indicates an telnet session can be established to the AP. …
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.21
cLApSshEnable
This object specifies whether SSH session can be established to the AP. A value of 'true' indicates an SSH session can be established to the AP. A …
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.22
cLApPreStdStateEnabled
This object specifies whether the pre-standard state of the AP is enabled or disabled. A value of 'true' indicates that the pre-standard state of the AP is enabled,…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.23
cLApPwrInjectorStateEnabled
This object specifies whether the power injector state of the AP is enabled or disabled. A value of 'true' indicates that the power injector state of the AP is enab…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.24
cLApPwrInjectorSelection
This object specifies the power injector selection value of the AP. 'unknown' - is returned if 'cLApPwrInjectorStateEnabled'is set to false. 'installed' - …
columnEnumeration.1.3.6.1.4.1.9.9.513.1.1.1.1.25
cLApPwrInjectorSwMacAddr
This object specifies the MAC address of the switch port that has a power Injector and is valid only when the 'cLApPwrInjectorSelection' is in 'installed' mode. if SET to 00:00:…
columnSNMPv2-TCMacAddress.1.3.6.1.4.1.9.9.513.1.1.1.1.26
cLApWipsEnable deprecated
This object represents if this AP is used as WIPS AP. A value of 'true' indicates that this AP is a WIPS AP. A value of 'false' indicates that this AP is not a WIPS AP. This appli…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.27
cLApMonitorModeOptimization
This object specifies the monitor mode optimization on this device. all - All optimization is enabled tracking - Tracking is optimized wips - WIPS optimizat…
columnEnumeration.1.3.6.1.4.1.9.9.513.1.1.1.1.28
cLApDomainName
This object specifies the domain, to which the AP belongs. This attribute can be configured only if the static IP option is turned on in the AP.
columnSNMP-FRAMEWORK-MIBSnmpAdminString.1.3.6.1.4.1.9.9.513.1.1.1.1.29
cLApMaxNumberOfDot11Slots
This object represents the maximum number of 802.11 radio interface slots in this AP.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.3
cLApNameServerAddressType
This object specifies the type of the IP address of the name server, made available through cLApNameServerAddress.
columnINET-ADDRESS-MIBInetAddressType.1.3.6.1.4.1.9.9.513.1.1.1.1.30
cLApNameServerAddress
This object specifies the IP Address of the name server. This attribute can be configured only if the static IP option is turned on in the AP.
columnINET-ADDRESS-MIBInetAddress.1.3.6.1.4.1.9.9.513.1.1.1.1.31
cLApAMSDUEnable
This object specifies the AMSDU status. A value of 'true' indicates AMSDU is enabled. A value of 'false' indicates AMSDU is disabled.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.32
cLApEncryptionSupported
This object specifies whether AP Supports DTLS encryption. A value of 'true' indicates encryption is supported. A value of 'false' indicates encryption is not sup…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.33
cLApRogueDetectionEnabled
This object specifies whether Rogue Detection is enabled in this AP. A value of 'true' indicates rogue detection is enabled. A value of 'false' indicates rogue de…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.34
cLApTcpMss
This object specifies the TCP Maximum Segment Size for this AP. Permissible value are between 536 and 1363. This will also enable the TCP MSS flag for this AP. Value of 0 will dis…
columnInteger32.1.3.6.1.4.1.9.9.513.1.1.1.1.35
cLApDataEncryptionStatus
This object represents the data encryption status of AP. A value of 'true' indicates data is encrypted between AP and WLC. A value of…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.36
cLApNsiKey
This object represents the network spectrum interface key used when the AP is in spectrum expert Only monitor mode (SOMM).This object returns a non-zero value only when the AP is…
columnOctetString.1.3.6.1.4.1.9.9.513.1.1.1.1.37
cLApAdminStatus
This object specifies the admin state of the AP, A value of 'true' indicates AP admin status is up. A value of 'false' indicates AP admin status is down.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.38
cLApPortNumber
This object represents the port number on which the AP's traffic is coming through.
columnINET-ADDRESS-MIBInetPortNumber.1.3.6.1.4.1.9.9.513.1.1.1.1.39
cLApEntPhysicalIndex
This object provides the index value in the entPhysicalEntry corresponding to this AP.
columnENTITY-MIBPhysicalIndex.1.3.6.1.4.1.9.9.513.1.1.1.1.4
cLApRetransmitCount
This object specifies the retransmission count for the access point control packet.This value specifies the number of packets retransmitted after which the Access Point falls back…
columnretries SNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.40
cLApRetransmitTimeout
This object specifies the retransmission timeout for the access point control packet. This value specifies the timeout for each retransmission, during the fallback of access point…
columnseconds SNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.41
cLApVenueConfigVenueGroup
This object specifies the venue group for this WLAN.
columnEnumeration.1.3.6.1.4.1.9.9.513.1.1.1.1.42
cLApVenueConfigVenueType
This object specifies the venue type within a particular venue group,for this WLAN. The venue group-venue type relationship is per the following table: Venue Group Venue Type Code…
columnEnumeration.1.3.6.1.4.1.9.9.513.1.1.1.1.43
cLApVenueConfigVenueName
This object specifies the venue name defined for this AP group.
columnSNMP-FRAMEWORK-MIBSnmpAdminString.1.3.6.1.4.1.9.9.513.1.1.1.1.44
cLApVenueConfigLanguage
This object specifies the language defined for this AP group.
columnSNMP-FRAMEWORK-MIBSnmpAdminString.1.3.6.1.4.1.9.9.513.1.1.1.1.45
cLApLEDState
This object specifies whether the LED state of this access point should be enabled or disabled. A value of 'true' indicates LED status is enabled. A value of 'false' indicates LED…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.46
cLApTrunkVlan
This object specifies the trunk VLAN ID assigned to this AP's ethernet interface. When a non-zero value is assigned for this Object, the management packets will be tagged with th…
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.47
cLApTrunkVlanStatus
This object specifies whether the trunk VLAN ID assigned to this AP's is effective. If the AP is unable to route the management frames through the trunk vlan, it will revert back …
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.48
cLApLocation
This object specifies the user specified location of this AP. While configuring AP, user should specify a location for the AP so that its easy to figure out for some one where the…
columnSNMP-FRAMEWORK-MIBSnmpAdminString.1.3.6.1.4.1.9.9.513.1.1.1.1.49
cLApName
This object specifies the administrative name assigned to the AP by the user. If an AP is not configured, its factory default name will be ap:<last three byte of MACAddress> eg.…
columnOctetString.1.3.6.1.4.1.9.9.513.1.1.1.1.5
cLApSubMode
This object specifies the sub mode of the AP. The option 'wips' applies only when the AP is in local, flexConnect or monitor mode. This 'pppoe' options apply only when the AP is…
columnEnumeration.1.3.6.1.4.1.9.9.513.1.1.1.1.50
cLApAssocCount
This object specifies the association count for the access point. This counter includes both successful and failed associate attempts, but does NOT include the re-associate atte…
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.51
cLApAssocFailResourceCount
This object specifies the association failure count for the access point due to the resource limits, i.e. the max clients of the WLAN/Radio is reached.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.52
cLApRealTimeStatsModeEnabled
This object specifies whether current stats mode is 'realtime'. There are two stats-mode, realtime and normal which specifies the stats-timer range to be 10-180 sec and 2-5 sec e…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.53
cLApAssociatedClientCount
This object represents the associated client number for the access point.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.54
cLApMemoryCurrentUsage
This object represents the percent of current memory usage of the access point.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.55
cLApMemoryAverageUsage
This object represents the percent of average memory usage of the access point. The statistics window is defined by clsSysStatisticsInterval.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.56
cLApCpuCurrentUsage
This object represents the percent of current CPU usage of the access point.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.57
cLApCpuAverageUsage
This object represents the percent of average CPU usage of the access point. The statistics window is defined by clsSysStatisticsInterval.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.58
cLApUpgradeFromVersion
This object represents the AP image upgrade from version.
columnSNMP-FRAMEWORK-MIBSnmpAdminString.1.3.6.1.4.1.9.9.513.1.1.1.1.59
cLApUpTime
This object represents the time in hundredths of a second since the last time the AP rebooted.
columnSNMPv2-SMITimeTicks.1.3.6.1.4.1.9.9.513.1.1.1.1.6
cLApUpgradeToVersion
This object represents the AP image upgrade to version.
columnSNMP-FRAMEWORK-MIBSnmpAdminString.1.3.6.1.4.1.9.9.513.1.1.1.1.60
cLApUpgradeFailureCause
This object represents the cause of the AP image upgrade failure.
columnSNMP-FRAMEWORK-MIBSnmpAdminString.1.3.6.1.4.1.9.9.513.1.1.1.1.61
cLApMaxClientLimitNumberTrap
This object represents the max client limit number.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.62
cLApMaxClientLimitCause
This object represents the cause of the max client limit reach.
columnSNMP-FRAMEWORK-MIBSnmpAdminString.1.3.6.1.4.1.9.9.513.1.1.1.1.63
cLApMaxClientLimitSet
This object represents whether this event is raised or cleared. A value of 'true' indicates this event is set. A value of 'false' indicates this even is cleared.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.64
cLApFloorLabel
This object specifies the floor label for the Access Point.
columnCISCO-TCUnsigned64.1.3.6.1.4.1.9.9.513.1.1.1.1.65
cLApConnectCount deprecated
This object represents the Count of AP's that are connected to the Controller.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.66
cLApReassocSuccCount
This object represents the successful re-association count for the Access Point.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.9.9.513.1.1.1.1.67
cLApReassocFailCount
This object represents the failed re-association count for the Access Point.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.9.9.513.1.1.1.1.68
cLAdjChannelRogueEnabled deprecated
This object specifies if rogue AP detection and removed Traps need to be sent. A value of 'true' indicates adjacent rogue detection is enabled. A value of 'false' indicates adjace…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.69
cLLwappUpTime
This object represents the time in hundredths of a second since the last time the AP joined the controller.
columnSNMPv2-SMITimeTicks.1.3.6.1.4.1.9.9.513.1.1.1.1.7
cLApAssocFailCountByRate
This object represents the failed association count for the access point caused by rate mismatch.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.70
cLApAbnormalOfflineCount
This object represents the abnormal offline count for the access point.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.71
cLApActiveClientCount
This object represents the active client number for the access point.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.72
cLApAssocFailCountForRssiLow
This object represents the failed association count for the access point caused by RSSI low.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.73
cLApSysNetId
This object specifies the ApSysNetId which is the numeric string to identify the system information like ApName.
columnSNMP-FRAMEWORK-MIBSnmpAdminString.1.3.6.1.4.1.9.9.513.1.1.1.1.74
cLApAssocFailTimes
This object represents the counts of client failed association to the access point.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.9.9.513.1.1.1.1.75
cLApAntennaBandMode
This object specifies the mode of antenna band. notApplicable - will return for unsuppported APs. single - configure the AP to use single band for antenna. dual - configure the …
columnEnumeration.1.3.6.1.4.1.9.9.513.1.1.1.1.76
cLApHeartBeatRspAvgTime
This object represents the average interval between sending the echo request and receiving the echo response in AP.
columnmilliseconds Integer32.1.3.6.1.4.1.9.9.513.1.1.1.1.77
cLApEchoRequestCount
This object represents the echo request packet count sent from AP to access controller.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.9.9.513.1.1.1.1.78
cLApEchoResponseLossCount
This object represents the echo response loss count from access controller to AP.
columnSNMPv2-SMICounter32.1.3.6.1.4.1.9.9.513.1.1.1.1.79
cLLwappJoinTakenTime
This object represents the time taken in hundredths of a second for the AP to join the controller. This could be a significant value in Mesh environments.
columnSNMPv2-SMITimeTicks.1.3.6.1.4.1.9.9.513.1.1.1.1.8
cLApModuleInserted
This object represents the type of the module inserted in to the AP.
columnSNMP-FRAMEWORK-MIBSnmpAdminString.1.3.6.1.4.1.9.9.513.1.1.1.1.80
cLApEnableModule
This object specifies the status of the external module . A value of 'true' indicates module is enabled. A value of 'false' indicates module is disabled.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.81
cLApIsUniversal
This object represents the if the AP is universal AP. A value of 'true' indicates AP is universal SKU based AP. A value of 'false' indicates AP is non-Universal SKU AP.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.82
cLApUniversalPrimeStatus
This object represents the method of Priming of the Universal AP.
columnSNMP-FRAMEWORK-MIBSnmpAdminString.1.3.6.1.4.1.9.9.513.1.1.1.1.83
cLApIsMaster
This object represents whether the flex AP is a master AP. This applies only to FlexExpress controllers. A value of 'true' indicates AP is a master AP. A value of 'false' indica…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.84
cLApBleFWDownloadStatus
This object represents the list of APs in which BLE firmware download is in progress. A value of 'true' indicates BLE download is in progress. A value of 'false' indicates BLE dow…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.85
cLApDot11XorDartConnectorStatus
This object represents the XOR dart connector status.
columnSNMP-FRAMEWORK-MIBSnmpAdminString.1.3.6.1.4.1.9.9.513.1.1.1.1.86
cLApCtsSxpDefaultPassword
This object specifies the SXP(Security Group Tag Exchange Protocol) default password.
columnSNMP-FRAMEWORK-MIBSnmpAdminString.1.3.6.1.4.1.9.9.513.1.1.1.1.87
cLApCtsSxpMode
This object specifies SXP(Security Group Tag Exchange Protocol) mode. A value of 'true' indicates sxp mode is enabled. A value of 'false' indicates sxp mode is disabled.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.89
cLApMaxNumberOfEthernetSlots
This object represents the maximum number of Ethernet slots in this AP.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.9
cLApCtsSxpListenerMinHoldtime
This object specifies SXP(Security Group Tag Exchange Protocol) listener hold time. It specifies the global maximum hold-time for SXP connections in 'listener' mode. …
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.90
cLApCtsSxpListenerMaxHoldtime
This object specifies SXP(Security Group Tag Exchange Protocol) listener hold time. It specifies the global maximum hold-time for SXP connections in 'listener' mode. …
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.91
cLApCtsSxpReconcilePeriod
This object specifies SXP(Security Group Tag Exchange Protocol) reconcile period.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.92
cLApCtsSxpRetryPeriod
This object specifies SXP(Security Group Tag Exchange Protocol) retry period.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.93
cLApCtsSxpSpeakerHoldTime
This object specifies SXP(Security Group Tag Exchange Protocol) speaker hold time.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.94
cLApCtsSxpSpeakerKeepAlive
This object specifies SXP(Security Group Tag Exchange Protocol) speaker keep alive time.
columnSNMPv2-SMIUnsigned32.1.3.6.1.4.1.9.9.513.1.1.1.1.95
cLApCtsInlineTagStatus
This object specifies Cisco Trustsec inline tagging is enabled/disabled. A value 'true' indicates inline tag is enabled. A value 'false' indicates inline tag is disabled.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.96
cLApCtsSgaclStatus
This object specifies Cisco Trustsec Security Group Tag ACL enforcement status. A value 'true' indicates SgACL enforcement is enabled A value 'false' indicates SgACL enforcement…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.97
cLApCtsOverrideStatus
This object specifies Cisco Trustsec AP Override status. A value of 'true' indicates CTS AP Override is enabled. A value of 'false' indicates CTS AP Override is disabled.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.513.1.1.1.1.98