POWER-ATTRIBUTES-MIB Table View
Table-centric layout grouping table, row, and column objects.
Tables
3
Rows
3
Columns
24
eoACPwrAttributesTable
table.1.3.6.1.2.1.230.1.1
·
1 row entry
·
12 columns
This table contains power attributes measurements for supported entPhysicalIndex entities. It is a sparse extension of the eoPowerTable.
This is a sparse extension of the eoPowerTable with
entries for power attributes measurements or
configuration. Each measured value corresponds to an
attribute in IEC 61850-7-4 for non-phase measurements
within the obj…
entries for power attributes measurements or
configuration. Each measured value corresponds to an
attribute in IEC 61850-7-4 for non-phase measurements
within the obj…
Indexes
ENTITY-MIBentPhysicalIndex
| Column | Syntax | OID | ||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
eoACPwrAttributesConfiguration
Configuration describes the physical configurations of
the power supply lines: * alternating current, single phase (SNGL) * alternating current, three-phase delta (DEL) * alternating current, thr… |
Enumeration Enumerated Values:
|
.1.3.6.1.2.1.230.1.1.1.1 |
||||||||||||||||||||||||||||||||||
|
eoACPwrAttributesAvgVoltage
A measured value for average of the voltage measured
over an integral number of AC cycles. For a three-phase system, this is the average voltage (V1+V2+V3)/3. IEC 61850-7-4 measured value attribute 'Vol'. |
0.1 Volt ACSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.2.1.230.1.1.1.2 |
||||||||||||||||||||||||||||||||||
|
eoACPwrAttributesAvgCurrent
A measured value for average of the current measured
over an integral number of AC cycles. For a three-phase system, this is the average current (I1+I2+I3)/3. IEC 61850-7-4 attribute 'Amp'. |
amperesSNMPv2-SMIUnsigned32 Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.2.1.230.1.1.1.3 |
||||||||||||||||||||||||||||||||||
|
eoACPwrAttributesFrequency
A measured value for the basic frequency of the AC
circuit. IEC 61850-7-4 attribute 'Hz'. |
0.01 hertzInteger32 Constraints: range: 4500-6500 |
.1.3.6.1.2.1.230.1.1.1.4 |
||||||||||||||||||||||||||||||||||
|
eoACPwrAttributesPowerUnitMultiplier
The magnitude of watts for the usage value in
eoACPwrAttributesTotalActivePower, eoACPwrAttributesTotalReactivePower, and eoACPwrAttributesTotalApparentPower measurements. For three-phase power systems, this will also i… |
ENERGY-OBJECT-MIBUnitMultiplier Textual Convention: ENERGY-OBJECT-MIBUnitMultiplier EnumerationType Values:
|
.1.3.6.1.2.1.230.1.1.1.5 |
||||||||||||||||||||||||||||||||||
|
eoACPwrAttributesPowerAccuracy
This object indicates a percentage value, in hundredths of a
percent, representing the presumed accuracy of active, reactive, and apparent power usage reporting. For example, 1010 means the reported usage is accurate t… |
hundredths of percentInteger32 Constraints: range: 0-10000 |
.1.3.6.1.2.1.230.1.1.1.6 |
||||||||||||||||||||||||||||||||||
|
eoACPwrAttributesTotalActivePower
A measured value of the actual power delivered to or
consumed by the load. IEC 61850-7-4 attribute 'TotW'. |
wattsSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.2.1.230.1.1.1.7 |
||||||||||||||||||||||||||||||||||
|
eoACPwrAttributesTotalReactivePower
A measured value of the reactive portion of the apparent
power. IEC 61850-7-4 attribute 'TotVAr'. |
volt-amperes reactiveSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.2.1.230.1.1.1.8 |
||||||||||||||||||||||||||||||||||
|
eoACPwrAttributesTotalApparentPower
A measured value of the voltage and current that
determines the apparent power. The apparent power is the vector sum of real and reactive power. Note: watts and volt-amperes are equivalent units and may … |
volt-amperesSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.2.1.230.1.1.1.9 |
||||||||||||||||||||||||||||||||||
|
eoACPwrAttributesTotalPowerFactor
A measured value ratio of the real power flowing to the
load versus the apparent power. It is dimensionless and expressed here as a percentage value in hundredths. A power factor of 100% indicates there is no inductan… |
hundredthsInteger32 Constraints: range: -10000-10000 |
.1.3.6.1.2.1.230.1.1.1.10 |
||||||||||||||||||||||||||||||||||
|
eoACPwrAttributesThdCurrent
A calculated value for the current total harmonic
distortion (THD). Method of calculation is not specified. IEC 61850-7-4 attribute 'ThdAmp'. |
hundredths of percentInteger32 Constraints: range: 0-10000 |
.1.3.6.1.2.1.230.1.1.1.11 |
||||||||||||||||||||||||||||||||||
|
eoACPwrAttributesThdVoltage
A calculated value for the voltage total harmonic
distortion (THD). The method of calculation is not specified. IEC 61850-7-4 attribute 'ThdVol'. |
hundredths of percentInteger32 Constraints: range: 0-10000 |
.1.3.6.1.2.1.230.1.1.1.12 |
.1.3.6.1.2.1.230.1.2
·
1 row entry
·
3 columns
This optional table describes three-phase power attributes
measurements in a DEL configuration with phase-to-phase
power attributes measurements. Entities having single
phase power shall not have any entities. This is a
sparse extension of the eoACPwrAttributesTable.
These attributes correspond to measurements related to
the IEC 61850-7.4 MMXU phase and measured harmonic or
interharmonics related to the MHAI phase.
An entry describes power measurements of a phase in a
DEL three-phase power. Three entries are required for each
supported entPhysicalIndex entry. Voltage measurements
are provided relative to each other.
…
DEL three-phase power. Three entries are required for each
supported entPhysicalIndex entry. Voltage measurements
are provided relative to each other.
…
Indexes
ENTITY-MIBentPhysicalIndex eoACPwrAttributesDelPhaseIndex
| Column | Syntax | OID |
|---|---|---|
|
eoACPwrAttributesDelPhaseIndex
A phase angle typically corresponding to 0, 120, 240.
|
Integer32 Constraints: range: 0-359 |
.1.3.6.1.2.1.230.1.2.1.1 |
|
eoACPwrAttributesDelPhaseToNextPhaseVoltage
A measured value of phase to next phase voltages, where
the next phase is IEC 61850-7-4 attribute 'PPV'. |
0.1 Volt ACSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.2.1.230.1.2.1.2 |
|
eoACPwrAttributesDelThdPhaseToNextPhaseVoltage
A calculated value for the voltage total harmonic
distortion for phase to next phase. Method of calculation is not specified. IEC 61850-7-4 attribute 'ThdPPV'. |
hundredths of percentInteger32 Constraints: range: 0-10000 |
.1.3.6.1.2.1.230.1.2.1.3 |
.1.3.6.1.2.1.230.1.3
·
1 row entry
·
9 columns
This optional table describes three-phase power attributes
measurements in a WYE configuration with phase-to-neutral
power attributes measurements. Entities having single
phase power shall not have any entities. This is a sparse
extension of the eoACPwrAttributesTable.
These attributes correspond to measurements related to
the IEC 61850-7.4 MMXU phase and measured harmonic or
interharmonics related to the MHAI phase.
This table describes measurements of a phase in a WYE
three-phase power system. Three entries are required for
each supported entPhysicalIndex entry. Voltage
measurements are relative to neutral.
Each ent…
three-phase power system. Three entries are required for
each supported entPhysicalIndex entry. Voltage
measurements are relative to neutral.
Each ent…
Indexes
ENTITY-MIBentPhysicalIndex eoACPwrAttributesWyePhaseIndex
| Column | Syntax | OID |
|---|---|---|
|
eoACPwrAttributesWyePhaseIndex
A phase angle typically corresponding to 0, 120, 240.
|
Integer32 Constraints: range: 0-359 |
.1.3.6.1.2.1.230.1.3.1.1 |
|
eoACPwrAttributesWyePhaseToNeutralVoltage
A measured value of phase to neutral voltage. IEC
61850-7-4 attribute 'PNV'. |
0.1 Volt ACSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.2.1.230.1.3.1.2 |
|
eoACPwrAttributesWyeCurrent
A measured value of phase currents. IEC 61850-7-4
attribute 'A'. |
0.1 amperes ACSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.2.1.230.1.3.1.3 |
|
eoACPwrAttributesWyeActivePower
A measured value of the actual power delivered to or
consumed by the load with the magnitude indicated separately in eoPowerUnitMultiplier. IEC 61850-7-4 attribute 'W'. |
wattsSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.2.1.230.1.3.1.4 |
|
eoACPwrAttributesWyeReactivePower
A measured value of the reactive portion of the apparent
power with the magnitude of indicated separately in eoPowerUnitMultiplier. IEC 61850-7-4 attribute 'VAr'. |
volt-amperes reactiveSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.2.1.230.1.3.1.5 |
|
eoACPwrAttributesWyeApparentPower
A measured value of the voltage and current determines
the apparent power with the indicated separately in eoPowerUnitMultiplier. Active plus reactive power equals the total apparent power. Note: Watts a… |
volt-amperesSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.2.1.230.1.3.1.6 |
|
eoACPwrAttributesWyePowerFactor
A measured value ratio of the real power flowing to the
load versus the apparent power for this phase. IEC 61850-7-4 attribute 'PF'. Power Factor can be positive or negative where the sign should be in lead/lag (IEEE)… |
hundredthsInteger32 Constraints: range: -10000-10000 |
.1.3.6.1.2.1.230.1.3.1.7 |
|
eoACPwrAttributesWyeThdCurrent
A calculated value for the voltage total harmonic
distortion (THD) for phase to phase. Method of calculation is not specified. IEC 61850-7-4 attribute 'ThdA'. |
hundredths of percentInteger32 Constraints: range: 0-10000 |
.1.3.6.1.2.1.230.1.3.1.8 |
|
eoACPwrAttributesWyeThdPhaseToNeutralVoltage
A calculated value of the voltage total harmonic
distortion (THD) for phase to neutral. IEC 61850-7-4 attribute 'ThdPhV'. |
hundredths of percentInteger32 Constraints: range: 0-10000 |
.1.3.6.1.2.1.230.1.3.1.9 |