CISCO-ATM-CONN-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
6
Rows
6
Columns
124

ciscoAtmVplTable

table
.1.3.6.1.4.1.9.10.13.1.1.1 · 1 row entry · 51 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk ciscoAtmVplTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ATM-CONN-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ATM-CONN-MIB::ciscoAtmVplTable' 
The Virtual Path Link extension Table.
ciscoAtmVplEntry row .1.3.6.1.4.1.9.10.13.1.1.1.1
An entry in the Vpl table.This entry is used to model
a bi-directional Vpl. This table augments the atmVplTable
defined in RFC 1695. However it uses ifIndex and atmVplVpi
as an Index for historical reasons. The entrie…
Indexes
Column Syntax OID
ciscoAtmVplCastType
Vpl type is either a point to point connection or point
to multipoint root or leaf.
CastTyper/w
Type Values:
1pointToPoint
2pointToMultiPointRoot
3pointToMultiPointLeaf
 .1.3.6.1.4.1.9.10.13.1.1.1.1.1
ciscoAtmVplSpanType
Vpl span is either a transit one or a terminating one.
SpanType
Type Values:
1unknown
2transit
3terminate
4both
 .1.3.6.1.4.1.9.10.13.1.1.1.1.2
ciscoAtmVplConfigType
Vpl type is either a PVC, SVC, Soft PVC or Soft Passive half leg.
The half leg can be set to Passive through user configuration only.
ConfigTyper/w
Type Values:
1other
2permanent
3switch
4soft
5softPassive
 .1.3.6.1.4.1.9.10.13.1.1.1.1.3
ciscoAtmVplRxUpcMode
Usage Parameter Control opeartion is pass,tag,drop or
local shaping at this connection.
UpcStatusr/w
Type Values:
1passing
2tagging
3dropping
4localShaping
 .1.3.6.1.4.1.9.10.13.1.1.1.1.4
ciscoAtmVplConnState
The connection state of this VPL.
ConnStater/w
Type Values:
1setup
2release
3notInstalled
4down
5up
 .1.3.6.1.4.1.9.10.13.1.1.1.1.5
ciscoAtmVplOamLoopbkTxInterval
Frequency of OAM loopback cells generated.
secondsInteger32r/w
Constraints:
range: 5-60
 .1.3.6.1.4.1.9.10.13.1.1.1.1.6
ciscoAtmVplOamSegmentLoopback
Enable segment loopback on this virtual path.
EnableStatusr/w
Type Values:
1enable
2disable
 .1.3.6.1.4.1.9.10.13.1.1.1.1.7
ciscoAtmVplOamEndLoopback
Enable end to end loopback on this virtual path.
EnableStatusr/w
Type Values:
1enable
2disable
 .1.3.6.1.4.1.9.10.13.1.1.1.1.8
ciscoAtmVplOamAisEnable
Enable Alarm Indication Signal OAM cell generation
if the interafce goes down on a crossconnect virtual path.
EnableStatusr/w
Type Values:
1enable
2disable
 .1.3.6.1.4.1.9.10.13.1.1.1.1.9
ciscoAtmVplOamRdiEnable
Enable Remote Defect Indication OAM cell generation
if an Alarm Indication Signal OAM cell is received.
EnableStatusr/w
Type Values:
1enable
2disable
 .1.3.6.1.4.1.9.10.13.1.1.1.1.10
ciscoAtmVplInstallTime
The time stamp derived from sysUpTime when this VPL gets
created. The VPL entries are created/deleted as a by-product
of creating and deleting entries in the atmVplTable defined
in RFC1695.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
 .1.3.6.1.4.1.9.10.13.1.1.1.1.11
ciscoAtmVplInCells
The total number of cells received on this
VPL.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.1.1.1.12
ciscoAtmVplOutCells
The total number of cells transmitted on
this VPL.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.1.1.1.13
ciscoAtmVplCrossIfIndex
For point to point, this is the cross-connected VPL's
ifIndex of this VPL. For point to multi-point connection,
this will be the root VPL's ifIndex for a leaf VPL entry in
the multicast chain, or it's the 1st leaf fo…
IF-MIBInterfaceIndexOrZeror/w
Type Constraints:
range: 0..2147483647
Description:
This textual convention is an extension of the
InterfaceIndex convention. The latter defines a greater
than zero value used to identify an interface or interface
sub-layer in the managed system. This extension permits…
 .1.3.6.1.4.1.9.10.13.1.1.1.1.14
ciscoAtmVplCrossVpi
This specifies the VPI value of the VPL to which this VPL is
cross-connected. For point to multi-point connection, this is
the root VPL's VPI for the leaf entry. Similarly it is the
1st leaf's VPI value for the root ent…
Integer32r/w
Constraints:
range: 0-4095
 .1.3.6.1.4.1.9.10.13.1.1.1.1.15
ciscoAtmVplNextLeafIfIndex
For point to point, this is zero i.e. not used.
For point to multi-point connection, this will be the next
leaf VPL's ifIndex on the multicast chain. This will be 0
if this is the root VPL entry. If it's zero for a l…
IF-MIBInterfaceIndexOrZero
Type Constraints:
range: 0..2147483647
Description:
This textual convention is an extension of the
InterfaceIndex convention. The latter defines a greater
than zero value used to identify an interface or interface
sub-layer in the managed system. This extension permits…
 .1.3.6.1.4.1.9.10.13.1.1.1.1.16
ciscoAtmVplNextLeafVpi
For point to point, this is zero i.e. not used.
This apply only to point to multi-point connection,
this will be the next leaf VPL's VPI on the multicast chain.
Integer32
Constraints:
range: 0-4095
 .1.3.6.1.4.1.9.10.13.1.1.1.1.17
ciscoAtmVplRemoteAddr
Soft PVP target address if this is the calling side
Soft PVP source address if this is called side.
Atomically set ConnState, RemoteAddr
and RemoteVpi will create or delete a soft PVP.
Atomically set ConnState, Remote…
CISCO-ATM-IF-MIBNsapAtmAddrr/w
Type Constraints:
range: 20
 .1.3.6.1.4.1.9.10.13.1.1.1.1.18
ciscoAtmVplRemoteVpi
Soft PVP target VPI in calling side. 0 in called side.
Integer32r/w
Constraints:
range: 0-4095
 .1.3.6.1.4.1.9.10.13.1.1.1.1.19
ciscoAtmVplLocation
Indicate calling or called side of a soft PVP.
If ciscoAtmVplConfigType is not soft then
ciscoAtmVplLocation value should be ignored.
Location
Type Values:
1unknown
2calling
3called
 .1.3.6.1.4.1.9.10.13.1.1.1.1.20
ciscoAtmVplSlowRetryIntv
Soft PVP slow retry interval time in seconds.
Integer32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.9.10.13.1.1.1.1.21
ciscoAtmVplNumAttempts
Number of retries made to install this soft PVP
connection. If ciscoAtmVplConfigType is not soft then
ciscoAtmVplNumAttempts value should be ignored.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.1.1.1.22
ciscoAtmVplLastReleaseCause
Value of the Cause field of the Cause
Information Element in the last Release
Signalling message received for this SPVP.
Indicates the reason for the Release.
ciscoAtmVplConfigType is not soft then
ciscoAtmVplLastRelea…
Integer32
Constraints:
range: 1-127
 .1.3.6.1.4.1.9.10.13.1.1.1.1.23
ciscoAtmVplLogicalPortDef
Indicates whether the VPC at this VPL interface
is an Atm Logical Port interface.
Enumerationr/w
Enumerated Values:
1notLogicalIf
2isLogicalIf
 .1.3.6.1.4.1.9.10.13.1.1.1.1.24
ciscoAtmVplLogicalPortIndex
The ifTable index of the Atm logical port
interface associated with this VPL. Only valid if
the value of atmVplLogicalPortDef is isLogicalIf,
and the VPL row is active.
IF-MIBInterfaceIndexOrZero
Type Constraints:
range: 0..2147483647
Description:
This textual convention is an extension of the
InterfaceIndex convention. The latter defines a greater
than zero value used to identify an interface or interface
sub-layer in the managed system. This extension permits…
 .1.3.6.1.4.1.9.10.13.1.1.1.1.25
ciscoAtmVplUpcViolations
The total number of nonconforming cells detected
by Usage Parameter Control (UPC) for cells received
on this VPL.
On LS1010 systems, this counter is valid only if
equipped with the Feature Card - Per Flow Queueing.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.1.1.1.26
ciscoAtmVplEpdTpdCellDropsobsolete
Never implemented.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.1.1.1.27
ciscoAtmVplEpdTpdPacketDropsobsolete
Never implemented.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.1.1.1.28
ciscoAtmVplEpdTpdPacketsInobsolete
Never implemented.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.1.1.1.29
ciscoAtmVplClp1Dropsobsolete
Never implemented.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.1.1.1.30
ciscoAtmVplDefaultRxUpcTolerance
If the tolerance (CDVT for CBR, ABR, UBR connections, Maximum
Burst Size for VBR connectons) requested for Usage
Parameter Control is not explicitly specified in VPL creation,
this object contains the default that i…
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.9.10.13.1.1.1.1.31
ciscoAtmVplDefaultRxUpcVbrCdvt
If the Cell Delay Variation Tolerance (CDVT) requested for
Usage Parameter Control for a VBR connection is not explicitly
specified in VPL creation, this object contains the default
that is used. If CDVT is explicitl…
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.9.10.13.1.1.1.1.32
ciscoAtmVplLsPerVcqWrrWeight
Configure the weighting specified for a VP half-leg
within a service class to make the scheduling decision
among other active VPLs in the service class. This
is for transmit on the VPL on the interface. This
parameter o…
Integer32r/w
Constraints:
range: 1-15
 .1.3.6.1.4.1.9.10.13.1.1.1.1.33
ciscoAtmVplLsPerVcqTunnelIsShaped
Determines whether this is to be a -shaped- VP, per
the Lightstream per-VC queueing chipset. If the value
specified is TRUE, the VP is to be a shaped VP Tunnel.
Such a VP cannot be cross-connected. This object
is defi…
SNMPv2-TCTruthValuer/w
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.9.10.13.1.1.1.1.34
ciscoAtmVplLsPerVcqXmtQueuedCells
Number of cells received on this VPL and
residing on the per-connection queue. Note that
this value is not valid until the VPL is in an
active cross-connect. This object
is defined only when the switch is equipped wit…
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.1.1.1.35
ciscoAtmVplLsPerVcQThreshGrp
The Threshold Group to which the cell-queue for
cells received by this VP are queued. This object
is defined only when the switch is equipped with
the Lightstream per-VC queueing chipset.
CISCO-ATM-RM-MIBLsPerVcqThresholdGroup
Type Values:
1tg1
2tg2
3tg3
4tg4
5tg5
6tg6
7tg7
8tg8
9tg9
10tg10
11tg11
12tg12
13tg13
14tg14
15tg15
16tg16
 .1.3.6.1.4.1.9.10.13.1.1.1.1.36
ciscoAtmVplInClp0Cells
The total number of cells with the CLP bit clear
received on this VPL. Note that these cells may
subsequently be discarded.
This counter is valid only:
- if the VPL is not a Logical Interface (tunnel).
- on LS1010 sys…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.1.1.1.37
ciscoAtmVplInClp1Cells
The total number of cells with the CLP bit set
received on this VPL. Note that these cells may
subsequently be discarded.
This counter is valid only:
- if the VPL is not a Logical Interface (tunnel).
- on LS1010 syste…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.1.1.1.38
ciscoAtmVplOutClp0Cells
The total number of cells with the CLP bit clear
transmitted on this VPL.
This counter is valid only:
- if the VPL is not a Logical Interface (tunnel).
- on LS1010 systems, only those equipped with
the Feature Car…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.1.1.1.39
ciscoAtmVplOutClp1Cells
The total number of cells with the CLP bit set
transmitted on this VPL.
This counter is valid only:
- if the VPL is not a Logical Interface (tunnel).
- on LS1010 systems, only those equipped with
the Feature Card …
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.1.1.1.40
ciscoAtmVplCellDrops
The total number of cells received on this
VPL, but discarded.
This counter is valid only:
- if the VPL is not a Logical Interface (tunnel).
- on LS1010 systems, only those equipped with
Feature Card - Per Flow Qu…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.1.1.1.41
ciscoAtmVplClp0VcqFullCellDrops
The total number of cells received on this
VPL with the CLP bit clear, discarded because
the per-VC queue limit is exceeded.
This counter is valid only:
- if the VPL is not a Logical Interface (tunnel).
- on LS1010 sy…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.1.1.1.43
ciscoAtmVplVcqClpThreshCellDrops
The total number of cells received on this
VPL, discarded because the discard threshold
(as opposed to the queue-limit) is exceeded
on the per-VC queue, and the CLP bit is set.
This counter is valid only:
- if the VPL …
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.1.1.1.44
ciscoAtmVplLsPerVcqTunnelIsHierarchical
Determines whether this is to be a -Hierarchical- VP, per
the Lightstream per-VC queueing chipset. If the value
specified is TRUE, the VP is to be a Hierarchical VP Tunnel.
Such a VP cannot be cross-connected. This obje…
SNMPv2-TCTruthValuer/w
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.9.10.13.1.1.1.1.45
ciscoAtmVplRxNegTraffDescrIndex
Identifies the entry in the atmTrafficDescrParamTable which
contains negotiated traffic parameters applied to the receive
direction of this VPL.

This object is not instantiated if this VPL is not the call…
.1.3.6.1.4.1.9.10.13.1.1.1.1.46
ciscoAtmVplTxNegTraffDescrIndex
Identifies the entry in the atmTrafficDescrParamTable which
contains negotiated traffic parameters applied to the transmit
direction of this VPL.

This object is not instantiated if this VPL is not the cal…
.1.3.6.1.4.1.9.10.13.1.1.1.1.47
ciscoAtmVplSwFabOutCells
The total number of cells transmitted on
this VPL by the Switch Fabric. This object is not
instantiated on systems that do not have support for
collecting such statistics.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.1.1.1.48
ciscoAtmVplSwFabOutClp0Cells
The total number of cells with the CLP bit clear
transmitted on this VPL by the Switch Fabric. This object
is not instantiated for a VPL that is a logical interface
(VP Tunnel). This object is not instantiated on syst…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.1.1.1.49
ciscoAtmVplSwFabOutClp1Cells
The total number of cells with the CLP bit set transmitted
on this VPL by the Switch Fabric. This object is not
instantiated for a VPL that is a logical interface
(VP Tunnel). This object is not instantiated on system…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.1.1.1.50
ciscoAtmVplConnName
A human readable string that identifies this connection.
This object will return a zero-length string if value is
not set.
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.10.13.1.1.1.1.51
ciscoAtmVplConnType
This object represent the PVP Type for this connection.
- local connection within the node
- endToEnd across several nodes
This object serves as an information object for a
management system and has no function…
Enumerationr/w
Enumerated Values:
1local
2endToEnd
 .1.3.6.1.4.1.9.10.13.1.1.1.1.52

ciscoAtmVclTable

table
.1.3.6.1.4.1.9.10.13.1.2.1 · 1 row entry · 55 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk ciscoAtmVclTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ATM-CONN-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ATM-CONN-MIB::ciscoAtmVclTable' 
The Virtual Channel Link extension Table.
ciscoAtmVclEntry row .1.3.6.1.4.1.9.10.13.1.2.1.1
An entry in the Vcl table.This entry is used to model
a bi-directional Vcl. This table augments the atmVclTable
defined in RFC 1695. However it uses ifIndex, atmVclVpi
and atmVclVci as an Index for historical reasons.…
Indexes
Column Syntax OID
ciscoAtmVclCastType
Vcl type is either a point to point connection or point
to multipoint root or leaf.
CastTyper/w
Type Values:
1pointToPoint
2pointToMultiPointRoot
3pointToMultiPointLeaf
 .1.3.6.1.4.1.9.10.13.1.2.1.1.1
ciscoAtmVclSpanType
Vcl span is either a transit one or a terminating one.
SpanType
Type Values:
1unknown
2transit
3terminate
4both
 .1.3.6.1.4.1.9.10.13.1.2.1.1.2
ciscoAtmVclConfigType
Vcl type is either a PVC, SVC, Soft PVC or Soft Passive half leg.
The half leg can be set to Passive through user configuration only.
ConfigTyper/w
Type Values:
1other
2permanent
3switch
4soft
5softPassive
 .1.3.6.1.4.1.9.10.13.1.2.1.1.3
ciscoAtmVclRxUpcMode
Usage Parameter Control opeartion is pass,tag,drop or
local shaping at this connection.
UpcStatusr/w
Type Values:
1passing
2tagging
3dropping
4localShaping
 .1.3.6.1.4.1.9.10.13.1.2.1.1.4
ciscoAtmVclEpdEnable
Early Packet Discard option used for this VCL.
The use is as follows:
enable(1)
Packet-discard is enabled.
disable(2)
Packet-discard is disabled.
useTrafficDescr(3)
Packet-discard in the receive direction is as…
Enumerationr/w
Enumerated Values:
1enable
2disable
3useTrafficDescr
 .1.3.6.1.4.1.9.10.13.1.2.1.1.5
ciscoAtmVclConnState
The connection state of this VCL.
ConnStater/w
Type Values:
1setup
2release
3notInstalled
4down
5up
 .1.3.6.1.4.1.9.10.13.1.2.1.1.6
ciscoAtmVclOamLoopbkTxInterval
Frequency of OAM loopback cell are generated on this
virtual channel.
secondsInteger32r/w
Constraints:
range: 5-60
 .1.3.6.1.4.1.9.10.13.1.2.1.1.7
ciscoAtmVclOamSegmentLoopback
Enable segment loopback on this virtual channel.
EnableStatusr/w
Type Values:
1enable
2disable
 .1.3.6.1.4.1.9.10.13.1.2.1.1.8
ciscoAtmVclOamEndLoopback
Enable end to end loopback on this virtual channel.
EnableStatusr/w
Type Values:
1enable
2disable
 .1.3.6.1.4.1.9.10.13.1.2.1.1.9
ciscoAtmVclOamAisEnable
Enable Alarm Indication Signal OAM cell generation
if the interafce goes down on a crossconnect virtual
channel.
EnableStatusr/w
Type Values:
1enable
2disable
 .1.3.6.1.4.1.9.10.13.1.2.1.1.10
ciscoAtmVclOamRdiEnable
Enable Remote Defect Indication OAM cell generation
if an Alarm Indication Signal OAM cell is received.
EnableStatusr/w
Type Values:
1enable
2disable
 .1.3.6.1.4.1.9.10.13.1.2.1.1.11
ciscoAtmVclInstallTime
The time stamp derived from sysUpTime when this VCL gets
created. The VCL entries are created/deleted as a by-product
of creating and deleting entries in the atmVclTable defined
in RFC1695.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
 .1.3.6.1.4.1.9.10.13.1.2.1.1.12
ciscoAtmVclInCells
The total number of cells received on
this VCL.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.2.1.1.13
ciscoAtmVclOutCells
The total number of cells transmitted on
this VCL.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.2.1.1.14
ciscoAtmVclCrossIfIndex
For point to point, this is the cross-connected VCL's
ifIndex of this VCL. For point to multi-point connection,
this will be the root VCL's ifIndex for a leaf VCL entry in
the multicast chain, or it's the 1st leaf VC…
IF-MIBInterfaceIndexOrZeror/w
Type Constraints:
range: 0..2147483647
Description:
This textual convention is an extension of the
InterfaceIndex convention. The latter defines a greater
than zero value used to identify an interface or interface
sub-layer in the managed system. This extension permits…
 .1.3.6.1.4.1.9.10.13.1.2.1.1.15
ciscoAtmVclCrossVpi
This specifies the VPI value of the VCL to which this
VCL is cross-connected. For point to multi-point
connection, this is the root VCL's VPI for the leaf entry.
Similarly it is the 1st leaf's VPI value for the root …
Integer32r/w
Constraints:
range: 0-4095
 .1.3.6.1.4.1.9.10.13.1.2.1.1.16
ciscoAtmVclCrossVci
This specifies the VCI value of the VCL to which this
VCL is cross-connected. For point to multi-point
connection, this is the root VCL's VCI for the leaf
entry. Similarly it is the 1st leaf's VCI value for
the root…
Integer32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.9.10.13.1.2.1.1.17
ciscoAtmVclNextLeafIfIndex
For point to point, this is zero i.e. not used.
For point to multi-point connection, this will be
the next leaf VCL's ifIndex on the multicast chain.
This will be 0 if this is the root VCL entry.
If it's zero for a …
IF-MIBInterfaceIndexOrZero
Type Constraints:
range: 0..2147483647
Description:
This textual convention is an extension of the
InterfaceIndex convention. The latter defines a greater
than zero value used to identify an interface or interface
sub-layer in the managed system. This extension permits…
 .1.3.6.1.4.1.9.10.13.1.2.1.1.18
ciscoAtmVclNextLeafVpi
For point to point, this is zero i.e. not used.
This apply only to point to multi-point connection,
this will be the next leaf VCL's VPI on the multicast
chain.
Integer32
Constraints:
range: 0-4095
 .1.3.6.1.4.1.9.10.13.1.2.1.1.19
ciscoAtmVclNextLeafVci
For point to point, this is zero i.e. not used.
This apply only to point to multi-point connection,
this will be the next leaf VCL's VCI on the multicast
chain.
Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.9.10.13.1.2.1.1.20
ciscoAtmVclAalEncapFlag
Encapsulation type for terminating VC.
Enumerationr/w
Enumerated Values:
1other
2aal5Snap
3aal5Nlpid
4aal5FrNlpid
5aal5Mux
6aal34Smds
7aalQsAal
8aal5Ilmi
9aal5Lane
10aal5Pnni
 .1.3.6.1.4.1.9.10.13.1.2.1.1.21
ciscoAtmVclAalEncapProtocol
Protocol for terminating VC if EncapFlag is aal5Mux.
Enumerationr/w
Enumerated Values:
1other
2ip
3xns
4appletalk
5clns
6decnet
7novell
8apollo
9vines
 .1.3.6.1.4.1.9.10.13.1.2.1.1.22
ciscoAtmVclAalUserVcType
Following is the list of user virtual circuit types in
case aal5Lane encapusation on this virtual channel.
boxConfigure -- The shared Server/Client end of a
Configure VCC
busForward -- The BUS end of t…
Enumerationr/w
Enumerated Values:
1other
2boxConfigure
3busForward
4busSend
5clientConfigure
6clientData
7clientDirect
8clientDistribute
9clientForward
10clientSend
11configure
12serverConfigure
13serverDirect
14serverDistribute
 .1.3.6.1.4.1.9.10.13.1.2.1.1.23
ciscoAtmVclAtmInArpInterval
Time interval in minutes to send InArp on a PVC for
IP over ATM. 0 will disable the InArp for this pvc.
minutesInteger32r/w
Constraints:
range: 0-60
 .1.3.6.1.4.1.9.10.13.1.2.1.1.24
ciscoAtmVclRemoteAddr
Soft PVC target address if this is the calling side
Soft PVC source address if this is called side.
Atomically set ConnState, RemoteAddr, RemoteVpi
and RemoteVci will create or delete a soft PVC.
Atomically set ConnSt…
CISCO-ATM-IF-MIBNsapAtmAddrr/w
Type Constraints:
range: 20
 .1.3.6.1.4.1.9.10.13.1.2.1.1.25
ciscoAtmVclRemoteVpi
Soft PVC target VPI in calling side. 0 in called side.
Integer32r/w
Constraints:
range: 0-4095
 .1.3.6.1.4.1.9.10.13.1.2.1.1.26
ciscoAtmVclRemoteVci
Soft PVC target VCI in calling side. 0 in called side.
Integer32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.9.10.13.1.2.1.1.27
ciscoAtmVclLocation
Indicate calling or called side of a soft PVC.
If ciscoAtmVclConfigType is not soft then
ciscoAtmVclLocation value should be ignored.
Location
Type Values:
1unknown
2calling
3called
 .1.3.6.1.4.1.9.10.13.1.2.1.1.28
ciscoAtmVclSlowRetryIntv
Soft PVC slow retry interval in seconds.
secondsInteger32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.9.10.13.1.2.1.1.29
ciscoAtmVclNumAttempts
Number of retries made to install this soft PVC
connection. If ciscoAtmVclConfigType is not soft then
ciscoAtmVclNumAttempts value should be ignored.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.2.1.1.30
ciscoAtmVclLastReleaseCause
Value of the Cause field of the Cause
Information Element in the last Release
Signalling message received for this SPVC.
Indicates the reason for the Release.
ciscoAtmVclConfigType is not soft then
ciscoAtmVclLastRelea…
Integer32
Constraints:
range: 1-127
 .1.3.6.1.4.1.9.10.13.1.2.1.1.31
ciscoAtmVclUpcViolations
The total number of nonconforming cells detected
by Usage Parameter Control (UPC) for cells received
on this VCL.
On LS1010 systems, this counter is valid only on those
equipped with the Feature Card - Per Flow Queueing.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.2.1.1.32
ciscoAtmVclEpdTpdCellDropsobsolete
Never implemented.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.2.1.1.33
ciscoAtmVclEpdTpdPacketDrops
The total number of EPD/TPD packet drops of
packets received on this VCL.
This counter is valid only:
- if EPD is enabled on this VCL.
- on LS1010 systems, only those equipped with
the Feature Card - Per Flow Queu…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.2.1.1.34
ciscoAtmVclEpdTpdPacketsIn
The total number of packets received in their
entirety on this VPL.
This counter is valid only:
- if EPD is enabled on this VCL.
- on LS1010 systems, only those equipped with
the Feature Card - Per Flow Queueing.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.2.1.1.35
ciscoAtmVclClp1Dropsobsolete
Never implemented.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.2.1.1.37
ciscoAtmVclDefaultRxUpcTolerance
If the tolerance (CDVT for CBR, ABR, UBR connections, Maximum
Burst Size for VBR connectons) requested for Usage
Parameter Control is not explicitly specified in VCL creation,
this object contains the default that is…
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.9.10.13.1.2.1.1.38
ciscoAtmVclDefaultRxUpcVbrCdvt
If the Cell Delay Variation Tolerance (CDVT) requested for
Usage Parameter Control for a VBR connection is not explicitly
specified in VCL creation, this object contains the default
that is used. If CDVT is explicitl…
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.9.10.13.1.2.1.1.39
ciscoAtmVclLsPerVcqWrrWeight
Configure the weighting specified for a VC half-leg
within a service class to make the scheduling decision
among other active VCLs in the service class. This
is for transmit on the VCL on the interface. This object
is d…
Integer32r/w
Constraints:
range: 1-15
 .1.3.6.1.4.1.9.10.13.1.2.1.1.40
ciscoAtmVclLsPerVcqXmtQueuedCells
Number of cells received on this VCL and
residing on the per-connection queue. Note that
this value is not valid until the VCL is in an
active cross-connect. This object
is defined only when the switch is equipped wit…
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.2.1.1.41
ciscoAtmVclLsPerVcQThreshGrp
The Threshold Group to which the cell-queue
for cells received by this VC are queued.
Note that this value is not valid until the
VCL is in an active cross-connect. This object
is defined only when the switch is equi…
CISCO-ATM-RM-MIBLsPerVcqThresholdGroup
Type Values:
1tg1
2tg2
3tg3
4tg4
5tg5
6tg6
7tg7
8tg8
9tg9
10tg10
11tg11
12tg12
13tg13
14tg14
15tg15
16tg16
 .1.3.6.1.4.1.9.10.13.1.2.1.1.42
ciscoAtmVclInClp0Cells
The total number of cells with the CLP bit clear
received on this VCL. Note that these cells may
subsequently be discarded.
This counter is valid only:
- on LS1010 systems, only those equipped with
Feature Card - P…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.2.1.1.43
ciscoAtmVclInClp1Cells
The total number of cells with the CLP bit set
received on this VCL. Note that these cells may
subsequently be discarded.
This counter is valid only:
- on LS1010 systems, only those equipped with
Feature Card - Per…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.2.1.1.44
ciscoAtmVclOutClp0Cells
The total number of cells with the CLP bit clear
transmitted on this VCL.
This counter is valid only:
- on LS1010 systems, only those equipped with
Feature Card - Per Flow Queueing.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.2.1.1.45
ciscoAtmVclOutClp1Cells
The total number of cells with the CLP bit set
transmitted on this VCL.
This counter is valid only:
- on LS1010 systems, only those equipped with
Feature Card - Per Flow Queueing.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.2.1.1.46
ciscoAtmVclCellDrops
The total number of cells received on this
VCL, but discarded.
This counter is valid only:
- on LS1010 systems, only those equipped with
Feature Card - Per Flow Queueing.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.2.1.1.47
ciscoAtmVclClp0VcqFullCellDrops
The total number of cells received on this
VCL with the CLP bit clear, discarded because
the per-VC queue limit is exceeded.
This counter is valid only:
- if EPD is disabled on the VCL.
- on LS1010 systems, only those…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.2.1.1.48
ciscoAtmVclVcqClpThreshCellDrops
The total number of cells received on this
VCL, discarded because the discard threshold
(as opposed to the queue-limit) is exceeded
on the per-VC queue, and the CLP bit is set.
This counter is valid only:
- if EPD is d…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.2.1.1.49
ciscoAtmVclRxNegTraffDescrIndex
Identifies the entry in the atmTrafficDescrParamTable which
contains negotiated traffic parameters applied to the receive
direction of this VCL.

This object is not instantiated if this VCL is not the call…
.1.3.6.1.4.1.9.10.13.1.2.1.1.50
ciscoAtmVclTxNegTraffDescrIndex
Identifies the entry in the atmTrafficDescrParamTable which
contains negotiated traffic parameters applied to the transmit
direction of this VCL.

This object is not instantiated if this VCL is not the cal…
.1.3.6.1.4.1.9.10.13.1.2.1.1.51
ciscoAtmVclSwFabOutCells
The total number of cells transmitted on
this VCL by the Switch Fabric. This object is not
instantiated on systems that do not have support for
collecting such statistics.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.2.1.1.52
ciscoAtmVclSwFabOutClp0Cells
The total number of cells with the CLP bit clear
transmitted on this VCL by the Switch Fabric.
This object is not instantiated on systems
that do not have support for collecting such
statistics.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.2.1.1.53
ciscoAtmVclSwFabOutClp1Cells
The total number of cells with the CLP bit set
transmitted on this VCL by the Switch Fabric.
This object is not instantiated on systems that
do not have support for collecting such statistics.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.13.1.2.1.1.54
ciscoAtmVclConnName
A human readable string that identifies this connection.
This object will return a zero-length string if value is
not set.
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.10.13.1.2.1.1.55
ciscoAtmVclConnType
This object represent the PVC Type for this connection.
- local connection within the node
- endToEnd across several nodes.
This object serves as an information object for a
management system and has no functional …
Enumerationr/w
Enumerated Values:
1local
2endToEnd
 .1.3.6.1.4.1.9.10.13.1.2.1.1.56

ciscoAtmSvpAddrTable

table
.1.3.6.1.4.1.9.10.13.1.3.1 · 1 row entry · 3 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk ciscoAtmSvpAddrTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ATM-CONN-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ATM-CONN-MIB::ciscoAtmSvpAddrTable' 
Switched virtual path link address table.
ciscoAtmSvpAddrEntry row .1.3.6.1.4.1.9.10.13.1.3.1.1
An entry in the Switched Vrtual Path address table.
Indexes
Column Syntax OID
ciscoAtmSvpAddr
It depends on the direction.This could be p2pCallingSide
address on a called side VPL, or p2pCalledSide address on a
calling side VPL or p2mpRoot address on a p2mp leaf side
VPL or p2mpLeaf address on a p2mp root sid…
OctetString
Constraints:
range: 20-20
 .1.3.6.1.4.1.9.10.13.1.3.1.1.1
ciscoAtmSvpVpi
This SVP's VPI value on this interface.
Integer32
Constraints:
range: 1-4095
 .1.3.6.1.4.1.9.10.13.1.3.1.1.2
ciscoAtmSvpDirection
Indicate whether this VPL is calling side, called side,
root or leaf for this address.
Direction
Type Values:
1unknown
2p2pCallingSide
3p2pCalledSide
4p2mpRoot
5p2mpLeaf
 .1.3.6.1.4.1.9.10.13.1.3.1.1.3

ciscoAtmSvcAddrTable

table
.1.3.6.1.4.1.9.10.13.1.4.1 · 1 row entry · 4 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk ciscoAtmSvcAddrTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ATM-CONN-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ATM-CONN-MIB::ciscoAtmSvcAddrTable' 
Switched virtual channel link address table.
ciscoAtmSvcAddrEntry row .1.3.6.1.4.1.9.10.13.1.4.1.1
An entry in the SVC address table.
Indexes
Column Syntax OID
ciscoAtmSvcAddr
It depends on the direction.This could be p2pCallingSide
address on a called side VCL, or p2pCalledSide address on a
calling side VCL or p2mpRoot address on a p2mp leaf side VCL
or p2mpLeaf address on a p2mp root sid…
OctetString
Constraints:
range: 20-20
 .1.3.6.1.4.1.9.10.13.1.4.1.1.1
ciscoAtmSvcVpi
This SVC's VPI value on this interface.
Integer32
Constraints:
range: 0-4095
 .1.3.6.1.4.1.9.10.13.1.4.1.1.2
ciscoAtmSvcVci
This SVC's VCI value on this interface.
Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.9.10.13.1.4.1.1.3
ciscoAtmSvcDirection
Indicate whether this VCL is calling side, called side,
root or leaf for this address.
Direction
Type Values:
1unknown
2p2pCallingSide
3p2pCalledSide
4p2mpRoot
5p2mpLeaf
 .1.3.6.1.4.1.9.10.13.1.4.1.1.4

ciscoAtmSnoopVcTable

table
.1.3.6.1.4.1.9.10.13.1.5.1 · 1 row entry · 6 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk ciscoAtmSnoopVcTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ATM-CONN-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ATM-CONN-MIB::ciscoAtmSnoopVcTable' 
Snooping VC Table.
ciscoAtmSnoopVcEntry row .1.3.6.1.4.1.9.10.13.1.5.1.1
An entry in the Snoop VC table. This entry models a VC snooping
connection. The ifIndex indicates the snooping interface, the
atmVclVpi and atmVclVci specifies the VPI and VCI value of the
snooping connection. To c…
Indexes
Column Syntax OID
ciscoAtmSnoopVcSnoopedIfIndex
This specifies the ifIndex of the snooped interface.
IF-MIBInterfaceIndexOrZeror/w
Type Constraints:
range: 0..2147483647
Description:
This textual convention is an extension of the
InterfaceIndex convention. The latter defines a greater
than zero value used to identify an interface or interface
sub-layer in the managed system. This extension permits…
 .1.3.6.1.4.1.9.10.13.1.5.1.1.1
ciscoAtmSnoopVcSnoopedVpi
This specifies the VPI value of the snooped connection endpoint.
Integer32r/w
Constraints:
range: 0-4095
 .1.3.6.1.4.1.9.10.13.1.5.1.1.2
ciscoAtmSnoopVcSnoopedVci
This specifies the VCI value of the snooped connection endpoint.
Integer32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.9.10.13.1.5.1.1.3
ciscoAtmSnoopVcDir
This specifies the traffic direction at the snooped connection
endpoint.
SnoopDirTyper/w
Type Values:
1transmit
2receive
 .1.3.6.1.4.1.9.10.13.1.5.1.1.4
ciscoAtmSnoopVcState
The connection state of this Snooping connetion.
ConnState
Type Values:
1setup
2release
3notInstalled
4down
5up
 .1.3.6.1.4.1.9.10.13.1.5.1.1.5
ciscoAtmSnoopVcRowStatus
This object is used to create a new row or delete an existing row
in this table. This gives the way to configure one-shot per-vc
snooping connection
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.9.10.13.1.5.1.1.6

ciscoAtmSnoopVpTable

table
.1.3.6.1.4.1.9.10.13.1.6.1 · 1 row entry · 5 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk ciscoAtmSnoopVpTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ATM-CONN-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ATM-CONN-MIB::ciscoAtmSnoopVpTable' 
Snooping VP Table.
ciscoAtmSnoopVpEntry row .1.3.6.1.4.1.9.10.13.1.6.1.1
An entry in the Snoop VP table. This entry models a VP snooping
connection. The ifIndex indicates the snooping interface, the
atmVclVpi specifies the VPI value of the snooping connection. To
create or destroy a snoo…
Indexes
Column Syntax OID
ciscoAtmSnoopVpSnoopedIfIndex
This specifies the ifIndex of the snooped interface.
IF-MIBInterfaceIndexOrZeror/w
Type Constraints:
range: 0..2147483647
Description:
This textual convention is an extension of the
InterfaceIndex convention. The latter defines a greater
than zero value used to identify an interface or interface
sub-layer in the managed system. This extension permits…
 .1.3.6.1.4.1.9.10.13.1.6.1.1.1
ciscoAtmSnoopVpSnoopedVpi
This specifies the VPI value of the snooped connection endpoint.
Integer32r/w
Constraints:
range: 0-4095
 .1.3.6.1.4.1.9.10.13.1.6.1.1.2
ciscoAtmSnoopVpDir
This specifies the traffic direction at the snooped connection
endpoint.
SnoopDirTyper/w
Type Values:
1transmit
2receive
 .1.3.6.1.4.1.9.10.13.1.6.1.1.3
ciscoAtmSnoopVpState
The connection state of this Snooping connection .
ConnState
Type Values:
1setup
2release
3notInstalled
4down
5up
 .1.3.6.1.4.1.9.10.13.1.6.1.1.4
ciscoAtmSnoopVpRowStatus
This object is used to create a new row or delete an existing row
in this table. This gives the way to configure one-shot per-vp
snooping connection
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.9.10.13.1.6.1.1.5