ciscoAtmVplConnState
CISCO-ATM-CONN-MIB ·
.1.3.6.1.4.1.9.10.13.1.1.1.1.5
Object
column
r/w
ConnState
The connection state of this VPL.
Context
- MIB
- CISCO-ATM-CONN-MIB
- OID
.1.3.6.1.4.1.9.10.13.1.1.1.1.5- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- ciscoAtmVplEntry
- Table
- ciscoAtmVplTable
- Siblings
- 50
Syntax
ConnState
- Source
- ConnState
- Base type
Enumeration
Values & Constraints
Type Values
1 | setup |
2 | release |
3 | notInstalled |
4 | down |
5 | up |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| ciscoAtmVplCastType Vpl type is either a point to point connection or point
to multipoint root or leaf. | column | CastType | .1.3.6.1.4.1.9.10.13.1.1.1.1.1 |
| ciscoAtmVplOamRdiEnable Enable Remote Defect Indication OAM cell generation
if an Alarm Indication Signal OAM cell is received. | column | EnableStatus | .1.3.6.1.4.1.9.10.13.1.1.1.1.10 |
| ciscoAtmVplInstallTime The time stamp derived from sysUpTime when this VPL gets
created. The VPL entries are created/deleted as a by-product
of creating and deleting entries in the atmVplTable defined… | column | SNMPv2-TCTimeStamp | .1.3.6.1.4.1.9.10.13.1.1.1.1.11 |
| ciscoAtmVplInCells The total number of cells received on this
VPL. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.12 |
| ciscoAtmVplOutCells The total number of cells transmitted on
this VPL. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.13 |
| ciscoAtmVplCrossIfIndex For point to point, this is the cross-connected VPL's
ifIndex of this VPL. For point to multi-point connection,
this will be the root VPL's ifIndex for a leaf VPL entry in
the … | column | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.9.10.13.1.1.1.1.14 |
| ciscoAtmVplCrossVpi This specifies the VPI value of the VPL to which this VPL is
cross-connected. For point to multi-point connection, this is
the root VPL's VPI for the leaf entry. Similarly it is t… | column | Integer32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.15 |
| ciscoAtmVplNextLeafIfIndex For point to point, this is zero i.e. not used.
For point to multi-point connection, this will be the next
leaf VPL's ifIndex on the multicast chain. This will be 0
if this is … | column | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.9.10.13.1.1.1.1.16 |
| ciscoAtmVplNextLeafVpi For point to point, this is zero i.e. not used.
This apply only to point to multi-point connection,
this will be the next leaf VPL's VPI on the multicast chain. | column | Integer32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.17 |
| ciscoAtmVplRemoteAddr Soft PVP target address if this is the calling side
Soft PVP source address if this is called side.
Atomically set ConnState, RemoteAddr
and RemoteVpi will create or delete a sof… | column | CISCO-ATM-IF-MIBNsapAtmAddr | .1.3.6.1.4.1.9.10.13.1.1.1.1.18 |
| ciscoAtmVplRemoteVpi Soft PVP target VPI in calling side. 0 in called side. | column | Integer32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.19 |
| ciscoAtmVplSpanType Vpl span is either a transit one or a terminating one. | column | SpanType | .1.3.6.1.4.1.9.10.13.1.1.1.1.2 |
| ciscoAtmVplLocation Indicate calling or called side of a soft PVP.
If ciscoAtmVplConfigType is not soft then
ciscoAtmVplLocation value should be ignored. | column | Location | .1.3.6.1.4.1.9.10.13.1.1.1.1.20 |
| ciscoAtmVplSlowRetryIntv Soft PVP slow retry interval time in seconds. | column | Integer32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.21 |
| ciscoAtmVplNumAttempts Number of retries made to install this soft PVP
connection. If ciscoAtmVplConfigType is not soft then
ciscoAtmVplNumAttempts value should be ignored. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.22 |
| ciscoAtmVplLastReleaseCause Value of the Cause field of the Cause
Information Element in the last Release
Signalling message received for this SPVP.
Indicates the reason for the Release.
ciscoAtmVplConfigTyp… | column | Integer32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.23 |
| ciscoAtmVplLogicalPortDef Indicates whether the VPC at this VPL interface
is an Atm Logical Port interface. | column | Enumeration | .1.3.6.1.4.1.9.10.13.1.1.1.1.24 |
| ciscoAtmVplLogicalPortIndex The ifTable index of the Atm logical port
interface associated with this VPL. Only valid if
the value of atmVplLogicalPortDef is isLogicalIf,
and the VPL row is active. | column | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.9.10.13.1.1.1.1.25 |
| ciscoAtmVplUpcViolations The total number of nonconforming cells detected
by Usage Parameter Control (UPC) for cells received
on this VPL.
On LS1010 systems, this counter is valid only if
equipped with th… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.26 |
| ciscoAtmVplEpdTpdCellDrops obsolete Never implemented. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.27 |
| ciscoAtmVplEpdTpdPacketDrops obsolete Never implemented. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.28 |
| ciscoAtmVplEpdTpdPacketsIn obsolete Never implemented. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.29 |
| ciscoAtmVplConfigType Vpl type is either a PVC, SVC, Soft PVC or Soft Passive half leg.
The half leg can be set to Passive through user configuration only. | column | ConfigType | .1.3.6.1.4.1.9.10.13.1.1.1.1.3 |
| ciscoAtmVplClp1Drops obsolete Never implemented. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.30 |
| ciscoAtmVplDefaultRxUpcTolerance If the tolerance (CDVT for CBR, ABR, UBR connections, Maximum
Burst Size for VBR connectons) requested for Usage
Parameter Control is not explicitly specified in VPL creation, … | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.31 |
| ciscoAtmVplDefaultRxUpcVbrCdvt If the Cell Delay Variation Tolerance (CDVT) requested for
Usage Parameter Control for a VBR connection is not explicitly
specified in VPL creation, this object contains the def… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.32 |
| ciscoAtmVplLsPerVcqWrrWeight Configure the weighting specified for a VP half-leg
within a service class to make the scheduling decision
among other active VPLs in the service class. This
is for transmit on th… | column | Integer32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.33 |
| ciscoAtmVplLsPerVcqTunnelIsShaped Determines whether this is to be a -shaped- VP, per
the Lightstream per-VC queueing chipset. If the value
specified is TRUE, the VP is to be a shaped VP Tunnel.
Such a VP cannot… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.10.13.1.1.1.1.34 |
| ciscoAtmVplLsPerVcqXmtQueuedCells Number of cells received on this VPL and
residing on the per-connection queue. Note that
this value is not valid until the VPL is in an
active cross-connect. This object
is defi… | column | SNMPv2-SMIGauge32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.35 |
| ciscoAtmVplLsPerVcQThreshGrp The Threshold Group to which the cell-queue for
cells received by this VP are queued. This object
is defined only when the switch is equipped with
the Lightstream per-VC queuein… | column | CISCO-ATM-RM-MIBLsPerVcqThresholdGroup | .1.3.6.1.4.1.9.10.13.1.1.1.1.36 |
| ciscoAtmVplInClp0Cells The total number of cells with the CLP bit clear
received on this VPL. Note that these cells may
subsequently be discarded.
This counter is valid only:
- if the VPL is not a Logi… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.37 |
| ciscoAtmVplInClp1Cells The total number of cells with the CLP bit set
received on this VPL. Note that these cells may
subsequently be discarded.
This counter is valid only:
- if the VPL is not a Logica… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.38 |
| ciscoAtmVplOutClp0Cells The total number of cells with the CLP bit clear
transmitted on this VPL.
This counter is valid only:
- if the VPL is not a Logical Interface (tunnel).
- on LS1010 systems, only… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.39 |
| ciscoAtmVplRxUpcMode Usage Parameter Control opeartion is pass,tag,drop or
local shaping at this connection. | column | UpcStatus | .1.3.6.1.4.1.9.10.13.1.1.1.1.4 |
| ciscoAtmVplOutClp1Cells The total number of cells with the CLP bit set
transmitted on this VPL.
This counter is valid only:
- if the VPL is not a Logical Interface (tunnel).
- on LS1010 systems, only t… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.40 |
| ciscoAtmVplCellDrops The total number of cells received on this
VPL, but discarded.
This counter is valid only:
- if the VPL is not a Logical Interface (tunnel).
- on LS1010 systems, only those equi… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.41 |
| ciscoAtmVplClp0VcqFullCellDrops The total number of cells received on this
VPL with the CLP bit clear, discarded because
the per-VC queue limit is exceeded.
This counter is valid only:
- if the VPL is not a Log… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.43 |
| ciscoAtmVplVcqClpThreshCellDrops The total number of cells received on this
VPL, discarded because the discard threshold
(as opposed to the queue-limit) is exceeded
on the per-VC queue, and the CLP bit is set.
Th… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.44 |
| ciscoAtmVplLsPerVcqTunnelIsHierarchical Determines whether this is to be a -Hierarchical- VP, per
the Lightstream per-VC queueing chipset. If the value
specified is TRUE, the VP is to be a Hierarchical VP Tunnel.
Such a… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.10.13.1.1.1.1.45 |
| ciscoAtmVplRxNegTraffDescrIndex Identifies the entry in the atmTrafficDescrParamTable which
contains negotiated traffic parameters applied to the receive
direction of this VPL.
This object is not … | column | - | .1.3.6.1.4.1.9.10.13.1.1.1.1.46 |
| ciscoAtmVplTxNegTraffDescrIndex Identifies the entry in the atmTrafficDescrParamTable which
contains negotiated traffic parameters applied to the transmit
direction of this VPL.
This object is not… | column | - | .1.3.6.1.4.1.9.10.13.1.1.1.1.47 |
| ciscoAtmVplSwFabOutCells The total number of cells transmitted on
this VPL by the Switch Fabric. This object is not
instantiated on systems that do not have support for
collecting such statistics. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.48 |
| ciscoAtmVplSwFabOutClp0Cells The total number of cells with the CLP bit clear
transmitted on this VPL by the Switch Fabric. This object
is not instantiated for a VPL that is a logical interface
(VP Tunnel). … | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.49 |
| ciscoAtmVplSwFabOutClp1Cells The total number of cells with the CLP bit set transmitted
on this VPL by the Switch Fabric. This object is not
instantiated for a VPL that is a logical interface
(VP Tunnel). T… | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.50 |
| ciscoAtmVplConnName A human readable string that identifies this connection.
This object will return a zero-length string if value is
not set. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.9.10.13.1.1.1.1.51 |
| ciscoAtmVplConnType This object represent the PVP Type for this connection.
- local connection within the node
- endToEnd across several nodes
This object serves as an information object for… | column | Enumeration | .1.3.6.1.4.1.9.10.13.1.1.1.1.52 |
| ciscoAtmVplOamLoopbkTxInterval Frequency of OAM loopback cells generated. | column | seconds Integer32 | .1.3.6.1.4.1.9.10.13.1.1.1.1.6 |
| ciscoAtmVplOamSegmentLoopback Enable segment loopback on this virtual path. | column | EnableStatus | .1.3.6.1.4.1.9.10.13.1.1.1.1.7 |
| ciscoAtmVplOamEndLoopback Enable end to end loopback on this virtual path. | column | EnableStatus | .1.3.6.1.4.1.9.10.13.1.1.1.1.8 |
| ciscoAtmVplOamAisEnable Enable Alarm Indication Signal OAM cell generation
if the interafce goes down on a crossconnect virtual path. | column | EnableStatus | .1.3.6.1.4.1.9.10.13.1.1.1.1.9 |