FS-MPLSOAM-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
3
Rows
3
Columns
43

fsMplsOamIgrTable

table
.1.3.6.1.4.1.52642.1.1.10.2.93.1.1.2 · 1 row entry · 12 columns
Open in standard view 
This table specifies information for configuring
and monitoring LSP(or te tunnel).
fsMplsOamIgrEntry entry .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.2.1
A row in this table represents information for configuring
and monitoring LSP(or te tunnel). It is indexed by
fsMplsOamIgrIndex, which uniquely identifies a single LSP(or te tunnel).
Indexes
fsMplsOamIgrIndex
Column Syntax OID
fsMplsOamIgrIndex
This is a unique index in the ingress table.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.2.1.1
fsMplsOamIgrLspName
The name of an LSP(or te tunnel).
OctetStringr/w .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.2.1.2
fsMplsOamIgrLspId
The ID of an LSP.
Integer32r/w
Constraints:
range: 1-65535
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.2.1.3
fsMplsOamIgrDetType
The OAM defect detection function is based on the periodic transmission
of CV or FFD packets from ingress to egress of an LSP. Each CV and FFD packet
carries a unique TTSI (Trail Termination Source Identifier), which …
Enumerationr/w
Enumerated Values:
1cv
2ffd
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.2.1.4
fsMplsOamIgrDetFreq
For CV: the frequency is 1s.
For FFD: the frequency is one of
50ms,100ms,200ms,500ms.
0: 1s(only for cv);
1: 50ms;
2: 100ms;
3: 200ms;
4: 500ms.
Enumerationr/w
Enumerated Values:
0cv1000ms
1ffd50ms2
2ffd100ms3
3ffd200ms4
4ffd500ms5
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.2.1.5
fsMplsOamIgrRevType
The BDI flow is injected on a return path (such as a return LSP) to inform the upstream LSR
(which is the source of the forward LSP) that there is a defect at the downstream LSP's LSR sink
point.BDI and loopback transac…
Enumerationr/w
Enumerated Values:
1private
2share
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.2.1.6
fsMplsOamIgrRevLspName
The name of a return LSP.
OctetStringr/w .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.2.1.7
fsMplsOamIgrEnable
The detection of OAM is enabled/disabled on the ingress of an LSP.
0: The OAM detection is disabled on the ingress;
1: The OAM detection is enabled on the ingress.
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.2.1.8
fsMplsOamIgrValid
0: stop detection of OAM;
1: start detection of OAM.
Integer32
Constraints:
range: 0-1
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.2.1.9
fsMplsOamIgrAvaState
If the LSP Timer (T3) expires, then the LSP enters the
Unavailable state. The start point of the Unavailable state
is deemed to be at the entry into the LSP defect state.
An LSP re-enters the Available state after fir…
Integer32
Constraints:
range: 0-1
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.2.1.10
fsMplsOamIgrDefectType
There are 6 types of defect in total, among which there are 4 MPLS layer user-plane
defects(i.e., dLOCV, dTTSI_Mismatch, dTTSI_Mismerge and dExcess), 1 Server layer defect,
1 peer maintenance entity defect:
0: no defect…
Integer32
Constraints:
range: 0-7
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.2.1.11
fsMplsOamIgrRowStatus
It is used to create and
delete a row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.2.1.12

fsMplsOamEgrTable

table
.1.3.6.1.4.1.52642.1.1.10.2.93.1.1.3 · 1 row entry · 16 columns
Open in standard view 
This table specifies information for configuring
and monitoring LSP(or te tunnel).
fsMplsOamEgrEntry entry .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.3.1
A row in this table represents information for configuring
and monitoring LSP(or te tunnel). It is indexed by
fsMplsOamEgrIndex, which uniquely identifies a single LSP(or te tunnel).
Indexes
fsMplsOamEgrIndex
Column Syntax OID
fsMplsOamEgrIndex
This is a unique index in the egress table.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.3.1.1
fsMplsOamEgrLspName
The name of static LSP at egress.
OctetStringr/w .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.3.1.2
fsMplsOamEgrLsrId
The Ingress LSR ID of an LSP.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.3.1.3
fsMplsOamEgrLspId
The ID of an LSP.
Integer32r/w
Constraints:
range: 1-65535
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.3.1.4
fsMplsOamEgrDetType
0: adaptability;
1: CV;
2: FFD.
Enumerationr/w
Enumerated Values:
0adaptability
1cv
2ffd
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.3.1.5
fsMplsOamEgrDetFreq
0: 1000ms(only for cv);
1: 50ms;
2: 100ms;
3: 200ms;
4: 500ms;
5: invalid.
Enumerationr/w
Enumerated Values:
0cv1000ms
1ffd50ms2
2ffd100ms3
3ffd200ms4
4ffd500ms5
5invalid6
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.3.1.6
fsMplsOamEgrRevType
The BDI flow is injected on a return path (such as a return LSP) to inform the upstream LSR
(which is the source of the forward LSP) that there is a defect at the downstream LSP's LSR sink
point.BDI and loopback transac…
Enumerationr/w
Enumerated Values:
0private
1share
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.3.1.7
fsMplsOamEgrRevLspName
The name of a return LSP.
OctetStringr/w .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.3.1.8
fsMplsOamEgrAutoEn
The adaptability is enabled/disabled.
0: disable;
1: enable.
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.3.1.9
fsMplsOamEgrAutoOvertime
The wait-time of adaptability.
Integer32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.3.1.10
fsMplsOamEgrBDIFreq
For CV: the frequency is 1s.
For FFD: the frequency is one of
50ms,100ms,200ms,500ms.
0: 1000ms(only for cv);
1: 50ms;
2: 100ms;
3: 200ms;
4: 500ms.
Enumerationr/w
Enumerated Values:
0cv1000ms
1ffd50ms2
2ffd100ms3
3ffd200ms4
4ffd500ms5
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.3.1.11
fsMplsOamEgrEnable
The detection of OAM is enabled/disabled on the egress of an LSP.
0: The OAM detection is disabled on the egress;
1: The OAM detection is enabled on the egress.
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.3.1.12
fsMplsOamEgrValid
1: stop detection of OAM;
2: start detection of OAM.
Enumeration
Enumerated Values:
1stop
2start
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.3.1.13
fsMplsOamEgrAvaState
If the LSP Timer (T1) expires, then the LSP enters the
Unavailable state. The start point of the Unavailable state
is deemed to be at the entry into the LSP defect state.
An LSP re-enters the Available state after the…
Integer32
Constraints:
range: 0-1
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.3.1.14
fsMplsOamEgrDefectType
There are 6 types of defect in total, among which there are 4 MPLS layer user-plane
defects(i.e., dLOCV, dTTSI_Mismatch, dTTSI_Mismerge and dExcess), 1 Server layer defect,
1 peer maintenance entity defect:
0: no defect…
Integer32
Constraints:
range: 0-7
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.3.1.15
fsMplsOamEgrRowStatus
It is used to create and
delete a row in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.1.3.1.16

fsMplsPsTable

table
.1.3.6.1.4.1.52642.1.1.10.2.93.1.3.1 · 1 row entry · 15 columns
Open in standard view 
This table specifies information for configuring
and monitoring LSP protection group(or te tunnel protection group).
fsMplsPsEntry entry .1.3.6.1.4.1.52642.1.1.10.2.93.1.3.1.1
A row in this table represents information for configuring
and monitoring LSP protection group(or te tunnel protection group). It is indexed by
fsMplsPsIndex, which uniquely identifies a single LSP protection group(or t…
Indexes
fsMplsPsIndex
Column Syntax OID
fsMplsPsIndex
This is a unique index in the protection group table.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.3.1.1.1
fsMplsPsGroupName
The protection group name.
OctetString .1.3.6.1.4.1.52642.1.1.10.2.93.1.3.1.1.2
fsMplsPsType
The MPLS PS architecture can be a 1+1 type, a 1:1 type, a shared mesh type,
or a packet 1+1 type.
1. In the 1+1 architecture type, a protection LSP is dedicated to each working
LSP with the working LSP bridged onto t…
Integer32
Constraints:
range: 1-4
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.3.1.1.3
fsMplsPsWorkLspName
The name of work-lsp(or work-tunnel).
OctetString .1.3.6.1.4.1.52642.1.1.10.2.93.1.3.1.1.4
fsMplsPsWorkLspId
The ID of work-lsp(or work-tunnel).
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.3.1.1.5
fsMplsPsProtectLspName
The name of protect-lsp.
OctetString .1.3.6.1.4.1.52642.1.1.10.2.93.1.3.1.1.6
fsMplsPsProtectLspId
The ID of protect-lsp(or protect-tunnel).
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.3.1.1.7
fsMplsPsRevertiveMode
The protection group revertive mode can be non-revertive and revertive
protection switching.
1. In revertive mode of operation, under conditions where working traffic
is being transmitted via the protection LSP and w…
Integer32
Constraints:
range: 1-2
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.3.1.1.8
fsMplsPsWTR
Wait to restore is only applicable for the revertive mode and
applies to a working LSP. It prevents reversion back to select
the working LSP until the wait to restore timer has expired.
The wait to restore time may be c…
Integer32
Constraints:
range: 0-60
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.3.1.1.9
fsMplsPsHoldOff
In general, if lower layer(e.g., SDH or optical) protection
mechanisms are being utilized in conjunction with MPLS layer
protection mechanisms, then the lower layers should have a
chance to restore working traffic befor…
Integer32
Constraints:
range: 0-100
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.3.1.1.10
fsMplsPsSwitchCondition
The following switch initiation criteria exist:
1. an externally initiated command(clear, lockout of protection,
forced switch, manual switch);
2. an automatically initiated command(signal fail) associated with
a…
Integer32
Constraints:
range: 1-9
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.3.1.1.11
fsMplsPsWorkLspState
The state of working lsp state lists below:
1: defect state;
2: non-defect state.
Integer32
Constraints:
range: 1-2
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.3.1.1.12
fsMplsPsProtLspState
The state of protection lsp state lists below:
1: defect state;
2: non-defect state.
Integer32
Constraints:
range: 1-2
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.3.1.1.13
fsMplsPsSwitchResult
Which lsp is user traffic being transmitted:
1: working-lsp;
2: protection-lsp.
Integer32
Constraints:
range: 1-2
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.3.1.1.14
fsMplsPsRowStatus
It is used to create and
delete a row in this table.
1: active;
2: notInService;
3: notReady;
4: createAndGo;
5: createAndWait;
6: destroy.
SNMPv2-TCRowStatus
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.52642.1.1.10.2.93.1.3.1.1.15