A3Com-PortPath-r6-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
6
Rows
6
Columns
93

a3ComPathTable

table mandatory
.1.3.6.1.4.1.43.2.16.2 · 1 row entry · 28 columns
Open in standard view 
A table of physical interfaces.
a3ComPathEntry entry .1.3.6.1.4.1.43.2.16.2.1
Indexes
a3ComPathIndex
Column Syntax OID
a3ComPathIndex mandatory
A unique identifier for each path. The
value for each path must remain constant at
least from one re-initialization of the entity's
network management system to the next re-initialization.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.16.2.1.1
a3ComPathName mandatory
A descriptive name for the path
OctetStringr/w
Constraints:
range: 0-20
 .1.3.6.1.4.1.43.2.16.2.1.2
a3ComPathPort mandatory
The index of the entry in the Port table to which
this path entry has been assigned. Unassigned entries
have a value of zero. This object allows adding and deleting
paths from ports.In order for any modifications to ta…
Integer32r/w
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.16.2.1.3
a3ComPathItcmOption mandatory
This object should be set to compatible if the
bridge/router is attached via a serial link to a
3Com Series/1 based bridge or bridge/router (IB/3, BR/3)
that contains an ITCM board.
Enumerationr/w
Enumerated Values:
1compatible
2incompatible
 .1.3.6.1.4.1.43.2.16.2.1.4
a3ComPathT1Mode mandatory
Enabling this object allows for better line speed than
if this were disabled. However, do not enable this object
when a3ComPathItcmOpt is set to compatible.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.43.2.16.2.1.5
a3ComPathCryptoResync mandatory
Enabling this parameter causes the router to resynch with
any attached KG84/91 devices. This only applies to the 449
interface of a wide area bridge/router.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.43.2.16.2.1.6
a3ComPathCRC mandatory
This controls the type of Cyclic Redundancy Check that
is performed on a serial line. In order for any modifications
to take effect, the path must be enabled(re-enabled if it is
already enable).
Enumerationr/w
Enumerated Values:
16crc16
32crc32
 .1.3.6.1.4.1.43.2.16.2.1.7
a3ComPathAdminStatus mandatory
This object enables or disables a path.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.43.2.16.2.1.8
a3ComPathOperStatus mandatory
The actual state of the path.
Enumeration
Enumerated Values:
1up
2down
3disabled
4notAvailable
5other
 .1.3.6.1.4.1.43.2.16.2.1.9
a3ComPathBaud obsolete
The baud rate for serial paths. For ethernet,
token ring, or FDDI connections this has a value
notApplicable(1). In order for any modifications
to take effect, the path must be enabled(re-enabled
if it is already enabl…
Enumerationr/w
Enumerated Values:
1notApplicable
2baud1200
3baud2400
4baud4800
5baud9600
6baud19200
7baud38400
8baud56k
9baud64k
10baud128k
11baud256k
12baud448k
13baud1536k
14baud2048k
15baud3072k
16baud4000k
17baud4608k
18baud6144k
19baud7680k
20baud9216k
21baud16000k
22other
 .1.3.6.1.4.1.43.2.16.2.1.10
a3ComPathConn mandatory
The connector for the path. For ethernet,
token ring, or FDDI connections this has a value
notApplicable(1). In order for any modifications
to take effect, the path must be enabled(re-enabled
if it is already enable). …
Enumerationr/w
Enumerated Values:
1notApplicable
2v35
3rs232
4rs449
5g703
6t3
7isdnBri
8isdnPri
9auto
10other
11x21
 .1.3.6.1.4.1.43.2.16.2.1.11
a3ComPathClock mandatory
How the transmit clock is derived. For ethernet,
token ring, or FDDI connections this has a value
notApplicable(1). In order for any modifications
to take effect, the path must be enabled(re-enabled
if it is already en…
Enumerationr/w
Enumerated Values:
1notApplicable
2internal
3external
 .1.3.6.1.4.1.43.2.16.2.1.12
a3ComPathLastChange mandatory
The value of sysUpTime at the time the path
entered its current operational state.
RFC1155-SMITimeTicks
Textual Convention: RFC1155-SMITimeTicks Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.43.2.16.2.1.13
a3ComPathSlotIndex mandatory
The index number of the chassis slot into which the module
(or board) that supports this Path is inserted.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.16.2.1.14
a3ComPathConnPos mandatory
The relative position on the module (or board) of the
physical connector that supports this path. The position
is identified by an index, which starts at one with the upper
left connector and continues left to right an…
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.16.2.1.15
a3ComPathInOctets mandatory
The total number of octets received on the
path, including framing characters.
RFC1155-SMICounter
Textual Convention: RFC1155-SMICounter Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.43.2.16.2.1.16
a3ComPathInUcastPkts mandatory
The number of subnetwork-unicast packets
delivered to a higher-layer protocol.
RFC1155-SMICounter
Textual Convention: RFC1155-SMICounter Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.43.2.16.2.1.17
a3ComPathInNUcastPkts mandatory
The number of non-unicast (i.e., subnetwork-
broadcast or subnetwork-multicast) packets
delivered to a higher-layer protocol.
RFC1155-SMICounter
Textual Convention: RFC1155-SMICounter Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.43.2.16.2.1.18
a3ComPathInDiscards mandatory
The number of inbound packets which were chosen
to be discarded even though no errors had been
detected to prevent their being deliverable to a
higher-layer protocol. One possible reason for
discarding such a packet co…
RFC1155-SMICounter
Textual Convention: RFC1155-SMICounter Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.43.2.16.2.1.19
a3ComPathInErrors mandatory
The number of inbound packets that contained
errors preventing them from being deliverable to a
higher-layer protocol.
RFC1155-SMICounter
Textual Convention: RFC1155-SMICounter Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.43.2.16.2.1.20
a3ComPathInUnknownProtos mandatory
The number of packets received via the path
which were discarded because of an unknown or
unsupported protocol.
RFC1155-SMICounter
Textual Convention: RFC1155-SMICounter Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.43.2.16.2.1.21
a3ComPathOutOctets mandatory
The total number of octets transmitted out of the
path, including framing characters.
RFC1155-SMICounter
Textual Convention: RFC1155-SMICounter Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.43.2.16.2.1.22
a3ComPathOutUcastPkts mandatory
The total number of packets that higher-level
protocols requested be transmitted to a
subnetwork-unicast address, including those that
were discarded or not sent.
RFC1155-SMICounter
Textual Convention: RFC1155-SMICounter Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.43.2.16.2.1.23
a3ComPathOutNUcastPkts mandatory
The total number of packets that higher-level
protocols requested be transmitted to a non-
unicast (i.e., a subnetwork-broadcast or
subnetwork-multicast) address, including those
that were discarded or not sent.
RFC1155-SMICounter
Textual Convention: RFC1155-SMICounter Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.43.2.16.2.1.24
a3ComPathOutDiscards mandatory
The number of outbound packets which were chosen
to be discarded even though no errors had been
detected to prevent their being transmitted. One
possible reason for discarding such a packet could
be to free up buffer s…
RFC1155-SMICounter
Textual Convention: RFC1155-SMICounter Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.43.2.16.2.1.25
a3ComPathOutErrors mandatory
The number of outbound packets that could not be
transmitted because of errors.
RFC1155-SMICounter
Textual Convention: RFC1155-SMICounter Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.43.2.16.2.1.26
a3ComPathBaudRate mandatory
The baud rate for serial paths. For ethernet,
token ring, or FDDI connections this reports the
actual value, but SETs are not allowed for those
Paths.

In order for any modifications to take effect, the …
Integer32r/w
Constraints:
range: 0-100000000
 .1.3.6.1.4.1.43.2.16.2.1.27
a3ComPathDuplex mandatory
The duplex mode is for SDLC and V3. It describes the physical
characteristics of the communication method used to control the
request-to-send signal. It has three values which are full, half
and auto.

Th…
Enumerationr/w
Enumerated Values:
1full
2half
3auto
 .1.3.6.1.4.1.43.2.16.2.1.28

a3ComPortTable

table mandatory
.1.3.6.1.4.1.43.2.17.2 · 1 row entry · 25 columns
Open in standard view 
A table of attached or remotely connect
network segments.
a3ComPortEntry entry .1.3.6.1.4.1.43.2.17.2.1
Indexes
a3ComPortIndex
Column Syntax OID
a3ComPortIndex mandatory
A unique value for each port. This corresponds to ifIndex
for MIB II. The interface table from MIB II will contain
additional information for this port, including its type,
its name and its description.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.17.2.1.1
a3ComPortOwner mandatory
This object indicates the owner for this port.
User can set the owner using this object, however, if
the owner does not match the actual physical interface card
associated with this port, it is ignored.

…
Enumerationr/w
Enumerated Values:
1ethernet
2tokenRing
3fddi
4ppp
5plg
6x25
7frameRelay
8smds
9auto
10autoPpp
11autoFr
 .1.3.6.1.4.1.43.2.17.2.1.2
a3ComPortBoundaryRoute mandatory
This object controls whether the Boundary Routing feature is
enabled for this port. Note: this feature only applies to
serial ports on a NB2 and will be disabled for non-serial ports.

Note, when this pa…
Enumerationr/w
Enumerated Values:
1notApplicable
2enabled
3disabled
 .1.3.6.1.4.1.43.2.17.2.1.3
a3ComPortBoundaryEncap mandatory
This object decides the packet encapsulation rules
to be applied to outgoing packets. If this is set
to none (5), the boundary router on the other end of
the serial link is capable of supporting translation.
In this ca…
Enumerationr/w
Enumerated Values:
1notApplicable
2ethernet
3tokenring
4fddi
5none
 .1.3.6.1.4.1.43.2.17.2.1.4
a3ComPortCosInterleave obsolete
(For bridging.) The number of high-priority packets
that will be transmitted for each low-priority
packet. If the value is 0, then low-priority packets
will only be transmitted when there are no packets
in the high-prio…
Integer32r/w
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.17.2.1.5
a3ComPortMacAddrFmtARP mandatory
This object indicates the MAC address format used
in ARP packets sent by this port. Note, nonCanonical(2)
is allowed only on Token Ring ports.
Enumerationr/w
Enumerated Values:
1canonical
2nonCanonical
 .1.3.6.1.4.1.43.2.17.2.1.6
a3ComPortMacAddrFmtIPX mandatory
This determine the MAC address format used in
IPX packets sent by this port. Note, nonCanonical(2)
is allowed only on Token Ring ports.
Enumerationr/w
Enumerated Values:
1canonical
2nonCanonical
 .1.3.6.1.4.1.43.2.17.2.1.7
a3ComPortMacAddrFmtXNS mandatory
This determines the MAC address format used in
XNS packets sent by this port. Note, nonCanonical(2)
is allowed only on Token Ring ports.
Enumerationr/w
Enumerated Values:
1canonical
2nonCanonical
 .1.3.6.1.4.1.43.2.17.2.1.8
a3ComPortPath mandatory
The Path which is assigned to this port. In some cases,
one or more Paths will be assigned to a single Port. This
object will return the lowest number Path in that case.
For those situations where more than one Port i…
Integer32r/w
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.17.2.1.9
a3ComQueueInterleave1 mandatory
This object specifies the interleave factor between
the high and medium priority port queues.

Note, this applies only to HSS ports. For non-HSS ports,
this object will have the value 0.
Integer32r/w
Constraints:
range: 0-10
 .1.3.6.1.4.1.43.2.17.2.1.10
a3ComQueueInterleave2 mandatory
This object specifies the interleave factor between
the medium and low priority port queues.

Note, this applies only to HSS ports. For non-HSS ports,
this object will have the value 0.
Integer32r/w
Constraints:
range: 0-10
 .1.3.6.1.4.1.43.2.17.2.1.11
a3ComQueuePattern mandatory
This identifies the relative ratios of high priority packets
versus medium priority packets versus low priority packets
(in that order) that will be transmitted by this port. These
ratios are based on the current valu…
Enumeration
Enumerated Values:
1ratio3to3to2
2ratio4to2to2
3ratio4to3to1
4ratio5to2to1
5ratio6to1to1
6other
 .1.3.6.1.4.1.43.2.17.2.1.13
a3ComPortAsOwnerTimer mandatory
This object only applies to High Speed Serial ports. When
the Owner of this port has been set to Auto, the system will
also automatically determine the proper Owner to assign to
the port. This object is used to ind…
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.17.2.1.15
a3ComSmartFilteringCtl mandatory
This object is used to enable or disable the Smart Filtering
mechanism on a port. Note, this only applies to the Central
Node in a boundary routing environment.

Note, when this parameter is enabled/disab…
Enumerationr/w
Enumerated Values:
1smartFilter
2noSmartFilter
 .1.3.6.1.4.1.43.2.17.2.1.16
a3ComBrCentralMacCtl mandatory
This object is used to enable or disable the Boundary
Routing Central MAC feature. If this feature is enabled,
(ie, if this object has the value centralMac(1)), the
Central Node (in a Boundary Routing environment) wil…
Enumerationr/w
Enumerated Values:
1centralMac
2noCentralMac
 .1.3.6.1.4.1.43.2.17.2.1.17
a3ComPortLabel mandatory
This object specifies the descriptive label assigned to this
port by the router. These labels are used by the User Interface
and are useful when comparing information retrieved via SNMP with
information retrieved via t…
RFC1213-MIBDisplayString
Textual Convention: RFC1213-MIBDisplayString OctetString
 .1.3.6.1.4.1.43.2.17.2.1.18
a3ComPortCircuitID mandatory
This object applies only to virtual ports and specifies the unique
data link circuit or channel identifier assigned to this virtual port.
For example, if this virtual port is attached to a Frame Relay network,
this ob…
OctetStringr/w .1.3.6.1.4.1.43.2.17.2.1.19
a3ComPortStatus mandatory
This object is used to add or delete virtual ports. When adding a new
virtual port, only the createAndGo method of adding rows is supported.
Specifically, all essential elements of the row must be specified in the
same…
RowStatusr/w
Textual Convention: RowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.43.2.17.2.1.20
a3ComPortName mandatory
The user-assigned name given to this port. Note, this name
may not have any blanks.
RFC1213-MIBDisplayStringr/w
Textual Convention: RFC1213-MIBDisplayString OctetString
 .1.3.6.1.4.1.43.2.17.2.1.21
a3ComPortVirtual mandatory
This object indicates whether this port is a virtual port or
a normal port.
Enumeration
Enumerated Values:
1normal
2virtual
 .1.3.6.1.4.1.43.2.17.2.1.22
a3ComQueueThrottle mandatory
This object specifies the maximum number of medium and low priority
packets that can be sent to the line driver each time some packets
are sent to the driver. A value of 0 means that there is no limit.
Integer32r/w
Constraints:
range: 0-40
 .1.3.6.1.4.1.43.2.17.2.1.23
a3ComPortInCallerId mandatory
A text string to specify the effective Incoming CallerID for the port.
This object must be successfully set for a port to use the dynamic dial
pool. It is used by the port to decide if an incoming call should be
accept…
OctetStringr/w
Constraints:
range: 0-31
 .1.3.6.1.4.1.43.2.17.2.1.24
a3ComPortCompType mandatory
This object specifies the type of compression performed on this Port.
NONE indicates that the compression is disabled. HIStory indicates
that the compression is enabled and preserves the History across the
frames and P…
Enumerationr/w
Enumerated Values:
1none
2history
3perPacket
 .1.3.6.1.4.1.43.2.17.2.1.25
a3ComPortX25ProtID mandatory
This object specifies the X25 ProtolID used when running in
Boundary Routed Mode for establishing the Virtual Circuits
over X25 Link.
Integer32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.43.2.17.2.1.26
a3ComPortIbmTraffic mandatory
This object is used to enable or disable the SmartFiltering
of IBM Traffic mechanism on a port. Note, this only applies to
the Central Node in a boundary routing environment.

Note, when this parameter i…
Enumerationr/w
Enumerated Values:
1ibmTraffic
2noibmTraffic
 .1.3.6.1.4.1.43.2.17.2.1.27

a3ComPathDialTable

table mandatory
.1.3.6.1.4.1.43.2.18.2 · 1 row entry · 15 columns
Open in standard view 
A table of physical interfaces.
a3ComPathDialEntry entry .1.3.6.1.4.1.43.2.18.2.1
Indexes
a3ComPathDialIndex
Column Syntax OID
a3ComPathDialIndex mandatory
A unique identifier for each path. The
value for each path must remain constant at
least from one re-initialization of the entity's
network management system to the next re-initialization.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.18.2.1.1
a3ComPathDialType mandatory
When assigning multiple paths for a single port,
and one or more of those paths is a dial-up Path,
this object must identify which Path is the primary
Path and whether it is a leased or dial-up Path.
Similarly, the oth…
Enumerationr/w
Enumerated Values:
1primaryLeased
2primaryDial
3secondaryDial
4other
5primaryAuto
6secondaryAuto
7secondaryLeased
8primaryAutoLeased
9primaryAutoDial
10secondaryAutoLeased
11secondaryAutoDial
 .1.3.6.1.4.1.43.2.18.2.1.2
a3ComPathDialCtl mandatory
For those Paths for which the value of a3ComPathDialType
is primaryDial(2) or secondaryDial(3), this object
is used to control whether that Path may originate and/or
answer calls.

If this object has the v…
Enumerationr/w
Enumerated Values:
1answerOriginate
2answerNoOriginate
3noAnswerOriginate
4noAnswerNoOriginate
 .1.3.6.1.4.1.43.2.18.2.1.3
a3ComPathDialAction mandatory
This object is used to initiate an action to be taken
by the primary dial-up Path. If this is set to dial(1),
then the Path is brought up using the number stored by
a3ComPathDialNum. This is only allowed for primary
…
Enumerationr/w
Enumerated Values:
1dial
2hangUp
3other
 .1.3.6.1.4.1.43.2.18.2.1.4
a3ComPathDialNum mandatory
This object contains the telephone number of the
remote sit to be dialed. This is used whenever
a dial-up Path is brought up. Spaces and hyphens (-)
are allowed and ignored, and semi-colons (;) indicate
a delay (as su…
OctetStringr/w
Constraints:
range: 0-30
 .1.3.6.1.4.1.43.2.18.2.1.5
a3ComPathDialDodIdleTime obsolete
This object applies only to a path that is setup as a PrimaryDial
path in DialOnDemand mode. It defines the amount of time, in seconds,
to wait after detecting the lack of user traffic on the dial path,
before bringing …
Integer32r/w
Constraints:
range: 1-3600
 .1.3.6.1.4.1.43.2.18.2.1.6
a3ComPathDialMode mandatory
This object is used for setting/reading the Dial Mode of a dialup path.

Only values (1) and (2) can be set to the object:
If the object is (1), the dialup path is configured for V25 mode dialing.
If the …
Enumerationr/w
Enumerated Values:
1v25Dial
2dtrDial
3autoV25
4autoDTR
 .1.3.6.1.4.1.43.2.18.2.1.7
a3ComPathDialDynCont mandatory
This object is used to specify whether the dialup path is of
type static(1) or dynamic(3). If a path is made dynamic, it
will automatically be assigned(added) into the pool of dynamic
paths. Making a path static will …
Enumerationr/w
Enumerated Values:
1static
2dynamic
3other
 .1.3.6.1.4.1.43.2.18.2.1.8
a3ComPathDialLocalDialNumber mandatory
The telephone number assigned to the local ISDN unit. This number and the
local subaddress number, if present, are used primarily to determine if the
unit should answer an incoming call. Valid only for ISDN. Any ASCII…
OctetStringr/w
Constraints:
range: 0-30
 .1.3.6.1.4.1.43.2.18.2.1.9
a3ComPathDialLocalSubAddress mandatory
The subaddress number assigned to the local ISDN unit. If the local dial
number criterion passes, then the local subaddress number, if present, is
the next criterion used to determine if an incoming call should be answ…
OctetStringr/w
Constraints:
range: 0-20
 .1.3.6.1.4.1.43.2.18.2.1.10
a3ComPathDialSPIDDN1 mandatory
The Service Profile Identification number assigned by a North American ISDN
switch provider to identify the service profile of a ISDN unit. Valid
characters are numeric IA5 characters ( 0 to 9 ). Maximum number of
ch…
OctetStringr/w
Constraints:
range: 0-37
 .1.3.6.1.4.1.43.2.18.2.1.11
a3ComPathDialSPIDDN2 mandatory
The second Service Profile Identification number assigned by a North
American ISDN switch provider to identify the service profile of a ISDN
unit. Valid characters are numeric IA5 characters ( 0 to 9 ). Maximum
number…
OctetStringr/w
Constraints:
range: 0-37
 .1.3.6.1.4.1.43.2.18.2.1.12
a3ComPathDialRateAdaption mandatory
Specifies the data rate to be used on the ISDN B channel. Rate64 and
Rate56 specify that the channel be connected at 64K or 56K, respectively.
The connection attempt would fail if the ISDN network does not support
this.…
Enumerationr/w
Enumerated Values:
1auto
2rate64
3rate56
 .1.3.6.1.4.1.43.2.18.2.1.13
a3ComPathDialSwitchType mandatory
Specifies the ISDN switch type the unit is connected to.

The path has to be enabled for the new setting to take effect.
Enumerationr/w
Enumerated Values:
1etsi
2ntt
3ni1
4att5ess
5dms100
 .1.3.6.1.4.1.43.2.18.2.1.14
a3ComPathDialExDevType mandatory
This object describes the external device type that is
connected to the serial-line type (eg, HSS, HDWAN) path. It is
applicable only for a dialup path.

Use bri(1) setting if the path is connected to a d…
Enumerationr/w
Enumerated Values:
1bri
2modem
3sw56
4other
 .1.3.6.1.4.1.43.2.18.2.1.15

a3ComPortDialTable

table mandatory
.1.3.6.1.4.1.43.2.19.2 · 1 row entry · 15 columns
Open in standard view 
A table of attached or remotely connect
network segments.
a3ComPortDialEntry entry .1.3.6.1.4.1.43.2.19.2.1
Indexes
a3ComPortDialIndex
Column Syntax OID
a3ComPortDialIndex mandatory
A unique value for each port. This corresponds to ifIndex
for MIB II. The interface table from MIB II will contain
additional information for this port, including its type,
its name and its description.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.19.2.1.1
a3ComPortDialDisasterCtl mandatory
This object applies only to those Ports to which
multiple Paths are assigned, at least one of which
is a dial-up Path.

If this is set to disasterRecovery(1), then this
Port will switch all its traffic to …
Enumerationr/w
Enumerated Values:
1disasterRecovery
2noDisasterRecovery
 .1.3.6.1.4.1.43.2.19.2.1.2
a3ComPortDialBandOnDmnd mandatory
This object applies only to those Ports to which
multiple Paths are assigned, at least one of which
is a dial-up Path.

If this is set to bandwidthOnDemand(1), then this Port
will switch all its traffic to…
Enumerationr/w
Enumerated Values:
1bandwidthOnDemand
2noBandwidthOnDemand
 .1.3.6.1.4.1.43.2.19.2.1.3
a3ComPortDialDebounceTimeUp mandatory
This object defines the amount of time, in seconds,
to wait after the primary Path has gone down before
bringing the secondary dial-up Path up.

If the primary Path stays in the down state for this
amount …
Integer32r/w
Constraints:
range: 0-3600
 .1.3.6.1.4.1.43.2.19.2.1.4
a3ComPortDialDebounceTimeDown mandatory
This object defines the amount of time, in seconds,
to wait after the primary Path has come up before
bringing the secondary, dial-up, Path down.

If the primary Path remains in the up state for this
amoun…
Integer32r/w
Constraints:
range: 0-3600
 .1.3.6.1.4.1.43.2.19.2.1.5
a3ComPortDialInitState mandatory
This object applies only to Ports which have paths setup as
PrimaryDial paths. It is used to configure the PrimaryDial
path as a dial initiator operating in one of the following modes:

noDialOut(1), whi…
Enumerationr/w
Enumerated Values:
1noDialOut
2manualDial
3dialOnDemand
 .1.3.6.1.4.1.43.2.19.2.1.6
a3ComPortDialRcvrState mandatory
This object applies only to Ports which have paths setup as PrimaryDial
paths. It is used to configure the PrimaryDial path as a dial receiver
operating in one of the following modes:

noAnswer(1), which d…
Enumerationr/w
Enumerated Values:
1noAnswer
2answer
 .1.3.6.1.4.1.43.2.19.2.1.7
a3ComPortDialAction mandatory
This object is used to initiate manual dial or hangup
action to be taken by the dialup port. If this is set to
dial(1), the port will attempt to dial out on its Primary
Dial path using the first destination phone number…
Enumerationr/w
Enumerated Values:
1dial
2hangUp
3other
 .1.3.6.1.4.1.43.2.19.2.1.8
a3ComPortDialDodIdleTime mandatory
This object applies only to a port that is setup as a dial initiator
in DialOnDemand mode. It defines the amount of time, in seconds, to
wait after detecting the lack of user traffic on its primary dial path
before brin…
Integer32r/w
Constraints:
range: 1-3600
 .1.3.6.1.4.1.43.2.19.2.1.9
a3ComPortDialIdleTime mandatory
This object applies only to a port that is setup as a dial initiator
in ManualDial mode. It defines the amount of time, in seconds, to wait
after detecting the lack of user traffic on any of its active dial
path befor…
Integer32r/w
Constraints:
range: 0-3600
 .1.3.6.1.4.1.43.2.19.2.1.10
a3ComPortDialDodCallsMade mandatory
The cumulative total number of outgoing calls successfully initiated
by the port operating in DialOnDemand mode.
RFC1155-SMICounter
Textual Convention: RFC1155-SMICounter Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.43.2.19.2.1.11
a3ComPortDialDodCallsFail mandatory
The cumulative total number of outgoing calls unsuccessfully initiated
by the port operating in DialOnDemand mode.
RFC1155-SMICounter
Textual Convention: RFC1155-SMICounter Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.43.2.19.2.1.12
a3ComPortDialDodUpTime mandatory
The cumulative length of time in seconds that the Primary path of a port
operating in DialOnDemand mode is Up.
RFC1155-SMICounter
Textual Convention: RFC1155-SMICounter Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.43.2.19.2.1.13
a3ComPortDialDodPktsOut mandatory
The cumulative total number of user-data packets sent out by the port operating
in DialOnDemand mode.
RFC1155-SMICounter
Textual Convention: RFC1155-SMICounter Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.43.2.19.2.1.14
a3ComPortDialBODTHreshold mandatory
%BODTHreshold% This object specifies the level of sensitivity to
bring up a BOD path for a port. The larger BODTHreshold value, the
less sensitive to bring up BOD path.
For DOD port, when the BODTHreshold is set to 0,…
Integer32r/w
Constraints:
range: 0-100
 .1.3.6.1.4.1.43.2.19.2.1.15

a3ComPortDialPoolPrefTable

table mandatory
.1.3.6.1.4.1.43.2.19.3 · 1 row entry · 4 columns
Open in standard view 
A table representing the PoolPreference lists for dynamic
dialup ports. A PoolPreference list is a prioritized list of
dynamic dial paths that a port can use, and it is optional.
Each entry in the list is represented as a row in the table, 
and it contains a dynamic dial path number and its priority-
postion in the list. Priority is in descending position order
and it specifies the preference of the port for a particular path.
All objects in this table are applicable only for a dynamic
dial port, ie, a port with an effective InCallerID, before these
objects are specified.
a3ComPortDialPoolPrefEntry entry .1.3.6.1.4.1.43.2.19.3.1
Indexes
a3ComPortDialPoolPrefPort a3ComPortDialPoolPrefPathPos
Column Syntax OID
a3ComPortDialPoolPrefPort mandatory
Specifies the port number(portid), used as an index
together with a3ComPortDialPoolPrefPathPos, to select
a particular row entry.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.19.3.1.1
a3ComPortDialPoolPrefPathPos mandatory
Specifies the position(priority) in the PoolPreference
list of a path, for the port. Used as an index together
with a3ComPortDialPoolPrefPort to select a particular
row entry.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.19.3.1.2
a3ComPortDialPoolPrefPathNum mandatory
Specifies the path number(pathid) of a dynamic dial
path that will be taken out from the dynamic dial pool
and added into the PoolPreference list for the port.
Integer32r/w
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.19.3.1.3
a3ComPortDialPoolPrefStatus mandatory
This object is used to add or delete a dynamic dial path
in the PoolPreference list of a port. Each path and its
position in the list is represented as a row. When adding
a new path, only the createAndGo method of addin…
RowStatusr/w
Textual Convention: RowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.43.2.19.3.1.4

a3ComPortDialPhoneListTable

table mandatory
.1.3.6.1.4.1.43.2.19.4 · 1 row entry · 6 columns
Open in standard view 
A table representing the PhoneNo lists for dialup ports.
Setting up a PhoneNo list is optional for static dialup port,
but is required for dynamic dialup port. 
A PhoneNo list is a prioritized list of destination phone
numbers that a port can use to dial out to. Each entry in
the list is represented as a row in the table and it contains
a phone number, the phone type, its baudrate and its priority
(position) in the list. Priority is in descending postion
order; and it specifies the preference of the port for a
particular phone number.
All objects in this table are applicable only for a dialup
port.
a3ComPortDialPhoneListEntry entry .1.3.6.1.4.1.43.2.19.4.1
Indexes
a3ComPortDialPhoneListPort a3ComPortDialPhoneListPos
Column Syntax OID
a3ComPortDialPhoneListPort mandatory
Specifies the port number(portid), used as an index
together with a3ComPortDialPhoneListPos, to select
a particular row entry.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.19.4.1.1
a3ComPortDialPhoneListPos mandatory
Specifies the position(priority) in the PhoneNo list of
a phone number, for this port. Used as an index
together with a3ComPortDialPhoneListPort, to select
a particular row entry.
Integer32
Textual Convention: COPS-PR-SPPIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.43.2.19.4.1.2
a3ComPortDialPhoneListPhoneNo mandatory
A text string representing a phone number in the PhoneNo list
of a port. The phone number is used as the destination phone
number to call for an outgoing call. In the case of an ISDN
dial line, this text string may als…
OctetStringr/w
Constraints:
range: 1-51
 .1.3.6.1.4.1.43.2.19.4.1.3
a3ComPortDialPhoneListType mandatory
Used to specify the phone type attribute of a phone number
in the PhoneNo list - either of type ISDN(1) or type Analog(2)
or other(3).
Enumerationr/w
Enumerated Values:
1iSDN
2analog
3other
 .1.3.6.1.4.1.43.2.19.4.1.4
a3ComPortDialPhoneListBaud mandatory
Used to specify the Baud rate attribute of a phone number in
the PhoneList.
Integer32r/w
Constraints:
range: 0-100000000
 .1.3.6.1.4.1.43.2.19.4.1.5
a3ComPortDialPhoneListStatus mandatory
This object is used to add or delete a phone number from the
PhoneNo list of a port. Each phone number and its associated
attributes (phone type, Baud rate, and priority-position) is
containned in a row. When adding a …
RowStatusr/w
Textual Convention: RowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.43.2.19.4.1.6