a3ComPortDialDisasterCtl
A3Com-PortPath-r6-MIB ·
.1.3.6.1.4.1.43.2.19.2.1.2
Object
column
mandatory
r/w
Enumeration
This object applies only to those Ports to which
multiple Paths are assigned, at least one of which
is a dial-up Path.
If this is set to disasterRecovery(1), then this
Port will switch all its traffic to the secondary
Path if the primary Path goes down.
Context
- MIB
- A3Com-PortPath-r6-MIB
- OID
.1.3.6.1.4.1.43.2.19.2.1.2- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- a3ComPortDialEntry
- Table
- a3ComPortDialTable
- Siblings
- 14
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | disasterRecovery |
2 | noDisasterRecovery |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| a3ComPortDialIndex mandatory A unique value for each port. This corresponds to ifIndex
for MIB II. The interface table from MIB II will contain
additional information for this port, including its type,
its … | column | Integer32 | .1.3.6.1.4.1.43.2.19.2.1.1 |
| a3ComPortDialIdleTime mandatory This object applies only to a port that is setup as a dial initiator
in ManualDial mode. It defines the amount of time, in seconds, to wait
after detecting the lack of user traff… | column | Integer32 | .1.3.6.1.4.1.43.2.19.2.1.10 |
| a3ComPortDialDodCallsMade mandatory The cumulative total number of outgoing calls successfully initiated
by the port operating in DialOnDemand mode. | column | RFC1155-SMICounter | .1.3.6.1.4.1.43.2.19.2.1.11 |
| a3ComPortDialDodCallsFail mandatory The cumulative total number of outgoing calls unsuccessfully initiated
by the port operating in DialOnDemand mode. | column | RFC1155-SMICounter | .1.3.6.1.4.1.43.2.19.2.1.12 |
| a3ComPortDialDodUpTime mandatory The cumulative length of time in seconds that the Primary path of a port
operating in DialOnDemand mode is Up. | column | RFC1155-SMICounter | .1.3.6.1.4.1.43.2.19.2.1.13 |
| a3ComPortDialDodPktsOut mandatory The cumulative total number of user-data packets sent out by the port operating
in DialOnDemand mode. | column | RFC1155-SMICounter | .1.3.6.1.4.1.43.2.19.2.1.14 |
| a3ComPortDialBODTHreshold mandatory %BODTHreshold% This object specifies the level of sensitivity to
bring up a BOD path for a port. The larger BODTHreshold value, the
less sensitive to bring up BOD path.
For DOD … | column | Integer32 | .1.3.6.1.4.1.43.2.19.2.1.15 |
| a3ComPortDialBandOnDmnd mandatory This object applies only to those Ports to which
multiple Paths are assigned, at least one of which
is a dial-up Path.
If this is set to bandwidthOnDemand(1), then … | column | Enumeration | .1.3.6.1.4.1.43.2.19.2.1.3 |
| a3ComPortDialDebounceTimeUp mandatory This object defines the amount of time, in seconds,
to wait after the primary Path has gone down before
bringing the secondary dial-up Path up.
If the primary Path … | column | Integer32 | .1.3.6.1.4.1.43.2.19.2.1.4 |
| a3ComPortDialDebounceTimeDown mandatory This object defines the amount of time, in seconds,
to wait after the primary Path has come up before
bringing the secondary, dial-up, Path down.
If the primary Pat… | column | Integer32 | .1.3.6.1.4.1.43.2.19.2.1.5 |
| a3ComPortDialInitState mandatory This object applies only to Ports which have paths setup as
PrimaryDial paths. It is used to configure the PrimaryDial
path as a dial initiator operating in one of the following… | column | Enumeration | .1.3.6.1.4.1.43.2.19.2.1.6 |
| a3ComPortDialRcvrState mandatory This object applies only to Ports which have paths setup as PrimaryDial
paths. It is used to configure the PrimaryDial path as a dial receiver
operating in one of the following mo… | column | Enumeration | .1.3.6.1.4.1.43.2.19.2.1.7 |
| a3ComPortDialAction mandatory This object is used to initiate manual dial or hangup
action to be taken by the dialup port. If this is set to
dial(1), the port will attempt to dial out on its Primary
Dial path … | column | Enumeration | .1.3.6.1.4.1.43.2.19.2.1.8 |
| a3ComPortDialDodIdleTime mandatory This object applies only to a port that is setup as a dial initiator
in DialOnDemand mode. It defines the amount of time, in seconds, to
wait after detecting the lack of user traf… | column | Integer32 | .1.3.6.1.4.1.43.2.19.2.1.9 |