a3ComPathDuplex
A3Com-PortPath-r6-MIB ·
.1.3.6.1.4.1.43.2.16.2.1.28
Object
column
mandatory
r/w
Enumeration
The duplex mode is for SDLC and V3. It describes the physical
characteristics of the communication method used to control the
request-to-send signal. It has three values which are full, half
and auto.
The path has to be (re)enabled for any new setting to take effect.
Context
- MIB
- A3Com-PortPath-r6-MIB
- OID
.1.3.6.1.4.1.43.2.16.2.1.28- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- a3ComPathEntry
- Table
- a3ComPathTable
- Siblings
- 27
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | full |
2 | half |
3 | auto |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| a3ComPathIndex mandatory A unique identifier for each path. The
value for each path must remain constant at
least from one re-initialization of the entity's
network management system to the next re-initi… | column | Integer32 | .1.3.6.1.4.1.43.2.16.2.1.1 |
| a3ComPathBaud obsolete The baud rate for serial paths. For ethernet,
token ring, or FDDI connections this has a value
notApplicable(1). In order for any modifications
to take effect, the path must be en… | column | Enumeration | .1.3.6.1.4.1.43.2.16.2.1.10 |
| a3ComPathConn mandatory The connector for the path. For ethernet,
token ring, or FDDI connections this has a value
notApplicable(1). In order for any modifications
to take effect, the path must be enable… | column | Enumeration | .1.3.6.1.4.1.43.2.16.2.1.11 |
| a3ComPathClock mandatory How the transmit clock is derived. For ethernet,
token ring, or FDDI connections this has a value
notApplicable(1). In order for any modifications
to take effect, the path must be… | column | Enumeration | .1.3.6.1.4.1.43.2.16.2.1.12 |
| a3ComPathLastChange mandatory The value of sysUpTime at the time the path
entered its current operational state. | column | RFC1155-SMITimeTicks | .1.3.6.1.4.1.43.2.16.2.1.13 |
| a3ComPathSlotIndex mandatory The index number of the chassis slot into which the module
(or board) that supports this Path is inserted. | column | Integer32 | .1.3.6.1.4.1.43.2.16.2.1.14 |
| a3ComPathConnPos mandatory The relative position on the module (or board) of the
physical connector that supports this path. The position
is identified by an index, which starts at one with the upper
left … | column | Integer32 | .1.3.6.1.4.1.43.2.16.2.1.15 |
| a3ComPathInOctets mandatory The total number of octets received on the
path, including framing characters. | column | RFC1155-SMICounter | .1.3.6.1.4.1.43.2.16.2.1.16 |
| a3ComPathInUcastPkts mandatory The number of subnetwork-unicast packets
delivered to a higher-layer protocol. | column | RFC1155-SMICounter | .1.3.6.1.4.1.43.2.16.2.1.17 |
| a3ComPathInNUcastPkts mandatory The number of non-unicast (i.e., subnetwork-
broadcast or subnetwork-multicast) packets
delivered to a higher-layer protocol. | column | RFC1155-SMICounter | .1.3.6.1.4.1.43.2.16.2.1.18 |
| a3ComPathInDiscards mandatory The number of inbound packets which were chosen
to be discarded even though no errors had been
detected to prevent their being deliverable to a
higher-layer protocol. One possibl… | column | RFC1155-SMICounter | .1.3.6.1.4.1.43.2.16.2.1.19 |
| a3ComPathName mandatory A descriptive name for the path | column | OctetString | .1.3.6.1.4.1.43.2.16.2.1.2 |
| a3ComPathInErrors mandatory The number of inbound packets that contained
errors preventing them from being deliverable to a
higher-layer protocol. | column | RFC1155-SMICounter | .1.3.6.1.4.1.43.2.16.2.1.20 |
| a3ComPathInUnknownProtos mandatory The number of packets received via the path
which were discarded because of an unknown or
unsupported protocol. | column | RFC1155-SMICounter | .1.3.6.1.4.1.43.2.16.2.1.21 |
| a3ComPathOutOctets mandatory The total number of octets transmitted out of the
path, including framing characters. | column | RFC1155-SMICounter | .1.3.6.1.4.1.43.2.16.2.1.22 |
| a3ComPathOutUcastPkts mandatory The total number of packets that higher-level
protocols requested be transmitted to a
subnetwork-unicast address, including those that
were discarded or not sent. | column | RFC1155-SMICounter | .1.3.6.1.4.1.43.2.16.2.1.23 |
| a3ComPathOutNUcastPkts mandatory The total number of packets that higher-level
protocols requested be transmitted to a non-
unicast (i.e., a subnetwork-broadcast or
subnetwork-multicast) address, including those
… | column | RFC1155-SMICounter | .1.3.6.1.4.1.43.2.16.2.1.24 |
| a3ComPathOutDiscards mandatory The number of outbound packets which were chosen
to be discarded even though no errors had been
detected to prevent their being transmitted. One
possible reason for discarding su… | column | RFC1155-SMICounter | .1.3.6.1.4.1.43.2.16.2.1.25 |
| a3ComPathOutErrors mandatory The number of outbound packets that could not be
transmitted because of errors. | column | RFC1155-SMICounter | .1.3.6.1.4.1.43.2.16.2.1.26 |
| a3ComPathBaudRate mandatory The baud rate for serial paths. For ethernet,
token ring, or FDDI connections this reports the
actual value, but SETs are not allowed for those
Paths.
In order fo… | column | Integer32 | .1.3.6.1.4.1.43.2.16.2.1.27 |
| a3ComPathPort mandatory The index of the entry in the Port table to which
this path entry has been assigned. Unassigned entries
have a value of zero. This object allows adding and deleting
paths from po… | column | Integer32 | .1.3.6.1.4.1.43.2.16.2.1.3 |
| a3ComPathItcmOption mandatory This object should be set to compatible if the
bridge/router is attached via a serial link to a
3Com Series/1 based bridge or bridge/router (IB/3, BR/3)
that contains an ITCM boa… | column | Enumeration | .1.3.6.1.4.1.43.2.16.2.1.4 |
| a3ComPathT1Mode mandatory Enabling this object allows for better line speed than
if this were disabled. However, do not enable this object
when a3ComPathItcmOpt is set to compatible. | column | Enumeration | .1.3.6.1.4.1.43.2.16.2.1.5 |
| a3ComPathCryptoResync mandatory Enabling this parameter causes the router to resynch with
any attached KG84/91 devices. This only applies to the 449
interface of a wide area bridge/router. | column | Enumeration | .1.3.6.1.4.1.43.2.16.2.1.6 |
| a3ComPathCRC mandatory This controls the type of Cyclic Redundancy Check that
is performed on a serial line. In order for any modifications
to take effect, the path must be enabled(re-enabled if it is
… | column | Enumeration | .1.3.6.1.4.1.43.2.16.2.1.7 |
| a3ComPathAdminStatus mandatory This object enables or disables a path. | column | Enumeration | .1.3.6.1.4.1.43.2.16.2.1.8 |
| a3ComPathOperStatus mandatory The actual state of the path. | column | Enumeration | .1.3.6.1.4.1.43.2.16.2.1.9 |