a3ComPathDialLocalDialNumber
A3Com-PortPath-r6-MIB ·
.1.3.6.1.4.1.43.2.18.2.1.9
Object
column
mandatory
r/w
OctetString
The telephone number assigned to the local ISDN unit. This number and the local subaddress number, if present, are used primarily to determine if the unit should answer an incoming call. Valid only for ISDN. Any ASCII characters up to 40 are acceptable inputs, but only the valid IA5 characters are used in the comparison. The path has to be enabled for the new setting to take effect.
Context
- MIB
- A3Com-PortPath-r6-MIB
- OID
.1.3.6.1.4.1.43.2.18.2.1.9- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- a3ComPathDialEntry
- Table
- a3ComPathDialTable
- Siblings
- 14
Syntax
OctetString
Values & Constraints
Object Constraints
range: 0-30
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| a3ComPathDialIndex mandatory A unique identifier for each path. The
value for each path must remain constant at
least from one re-initialization of the entity's
network management system to the next re-initi… | column | Integer32 | .1.3.6.1.4.1.43.2.18.2.1.1 |
| a3ComPathDialLocalSubAddress mandatory The subaddress number assigned to the local ISDN unit. If the local dial
number criterion passes, then the local subaddress number, if present, is
the next criterion used to dete… | column | OctetString | .1.3.6.1.4.1.43.2.18.2.1.10 |
| a3ComPathDialSPIDDN1 mandatory The Service Profile Identification number assigned by a North American ISDN
switch provider to identify the service profile of a ISDN unit. Valid
characters are numeric IA5 char… | column | OctetString | .1.3.6.1.4.1.43.2.18.2.1.11 |
| a3ComPathDialSPIDDN2 mandatory The second Service Profile Identification number assigned by a North
American ISDN switch provider to identify the service profile of a ISDN
unit. Valid characters are numeric IA… | column | OctetString | .1.3.6.1.4.1.43.2.18.2.1.12 |
| a3ComPathDialRateAdaption mandatory Specifies the data rate to be used on the ISDN B channel. Rate64 and
Rate56 specify that the channel be connected at 64K or 56K, respectively.
The connection attempt would fail if… | column | Enumeration | .1.3.6.1.4.1.43.2.18.2.1.13 |
| a3ComPathDialSwitchType mandatory Specifies the ISDN switch type the unit is connected to.
The path has to be enabled for the new setting to take effect. | column | Enumeration | .1.3.6.1.4.1.43.2.18.2.1.14 |
| a3ComPathDialExDevType mandatory This object describes the external device type that is
connected to the serial-line type (eg, HSS, HDWAN) path. It is
applicable only for a dialup path.
Use bri(1)… | column | Enumeration | .1.3.6.1.4.1.43.2.18.2.1.15 |
| a3ComPathDialType mandatory When assigning multiple paths for a single port,
and one or more of those paths is a dial-up Path,
this object must identify which Path is the primary
Path and whether it is a le… | column | Enumeration | .1.3.6.1.4.1.43.2.18.2.1.2 |
| a3ComPathDialCtl mandatory For those Paths for which the value of a3ComPathDialType
is primaryDial(2) or secondaryDial(3), this object
is used to control whether that Path may originate and/or
answer calls.… | column | Enumeration | .1.3.6.1.4.1.43.2.18.2.1.3 |
| a3ComPathDialAction mandatory This object is used to initiate an action to be taken
by the primary dial-up Path. If this is set to dial(1),
then the Path is brought up using the number stored by
a3ComPathDial… | column | Enumeration | .1.3.6.1.4.1.43.2.18.2.1.4 |
| a3ComPathDialNum mandatory This object contains the telephone number of the
remote sit to be dialed. This is used whenever
a dial-up Path is brought up. Spaces and hyphens (-)
are allowed and ignored, and… | column | OctetString | .1.3.6.1.4.1.43.2.18.2.1.5 |
| a3ComPathDialDodIdleTime obsolete This object applies only to a path that is setup as a PrimaryDial
path in DialOnDemand mode. It defines the amount of time, in seconds,
to wait after detecting the lack of user tr… | column | Integer32 | .1.3.6.1.4.1.43.2.18.2.1.6 |
| a3ComPathDialMode mandatory This object is used for setting/reading the Dial Mode of a dialup path.
Only values (1) and (2) can be set to the object:
If the object is (1), the dialup path is … | column | Enumeration | .1.3.6.1.4.1.43.2.18.2.1.7 |
| a3ComPathDialDynCont mandatory This object is used to specify whether the dialup path is of
type static(1) or dynamic(3). If a path is made dynamic, it
will automatically be assigned(added) into the pool of d… | column | Enumeration | .1.3.6.1.4.1.43.2.18.2.1.8 |