a3ComPortBoundaryEncap
A3Com-PortPath-r6-MIB ·
.1.3.6.1.4.1.43.2.17.2.1.4
Object
column
mandatory
r/w
Enumeration
This object decides the packet encapsulation rules
to be applied to outgoing packets. If this is set
to none (5), the boundary router on the other end of
the serial link is capable of supporting translation.
In this case, all bridged packets will be sent unchanged.
Boundary routed packets will be sent with the default
mode: Ethernet. All other settings of this object
implies that the remote device does not support translation.
Therefore, all packets must be encapsulated according to
this object. In order for any modifications to take
effect, the port associated with this command must be
disabled and then enabled.
Note, this only applies to serial ports on a NB2. For
all non-serial ports, this object will have the value
notApplicable(1).
Context
- MIB
- A3Com-PortPath-r6-MIB
- OID
.1.3.6.1.4.1.43.2.17.2.1.4- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- a3ComPortEntry
- Table
- a3ComPortTable
- Siblings
- 24
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | notApplicable |
2 | ethernet |
3 | tokenring |
4 | fddi |
5 | none |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| a3ComPortIndex mandatory A unique value for each port. This corresponds to ifIndex
for MIB II. The interface table from MIB II will contain
additional information for this port, including its type,
its … | column | Integer32 | .1.3.6.1.4.1.43.2.17.2.1.1 |
| a3ComQueueInterleave1 mandatory This object specifies the interleave factor between
the high and medium priority port queues.
Note, this applies only to HSS ports. For non-HSS ports,
this object … | column | Integer32 | .1.3.6.1.4.1.43.2.17.2.1.10 |
| a3ComQueueInterleave2 mandatory This object specifies the interleave factor between
the medium and low priority port queues.
Note, this applies only to HSS ports. For non-HSS ports,
this object w… | column | Integer32 | .1.3.6.1.4.1.43.2.17.2.1.11 |
| a3ComQueuePattern mandatory This identifies the relative ratios of high priority packets
versus medium priority packets versus low priority packets
(in that order) that will be transmitted by this port. The… | column | Enumeration | .1.3.6.1.4.1.43.2.17.2.1.13 |
| a3ComPortAsOwnerTimer mandatory This object only applies to High Speed Serial ports. When
the Owner of this port has been set to Auto, the system will
also automatically determine the proper Owner to assign t… | column | Integer32 | .1.3.6.1.4.1.43.2.17.2.1.15 |
| a3ComSmartFilteringCtl mandatory This object is used to enable or disable the Smart Filtering
mechanism on a port. Note, this only applies to the Central
Node in a boundary routing environment.
No… | column | Enumeration | .1.3.6.1.4.1.43.2.17.2.1.16 |
| a3ComBrCentralMacCtl mandatory This object is used to enable or disable the Boundary
Routing Central MAC feature. If this feature is enabled,
(ie, if this object has the value centralMac(1)), the
Central Node… | column | Enumeration | .1.3.6.1.4.1.43.2.17.2.1.17 |
| a3ComPortLabel mandatory This object specifies the descriptive label assigned to this
port by the router. These labels are used by the User Interface
and are useful when comparing information retrieved v… | column | RFC1213-MIBDisplayString | .1.3.6.1.4.1.43.2.17.2.1.18 |
| a3ComPortCircuitID mandatory This object applies only to virtual ports and specifies the unique
data link circuit or channel identifier assigned to this virtual port.
For example, if this virtual port is at… | column | OctetString | .1.3.6.1.4.1.43.2.17.2.1.19 |
| a3ComPortOwner mandatory This object indicates the owner for this port.
User can set the owner using this object, however, if
the owner does not match the actual physical interface card
associated with t… | column | Enumeration | .1.3.6.1.4.1.43.2.17.2.1.2 |
| a3ComPortStatus mandatory This object is used to add or delete virtual ports. When adding a new
virtual port, only the createAndGo method of adding rows is supported.
Specifically, all essential elements … | column | RowStatus | .1.3.6.1.4.1.43.2.17.2.1.20 |
| a3ComPortName mandatory The user-assigned name given to this port. Note, this name
may not have any blanks. | column | RFC1213-MIBDisplayString | .1.3.6.1.4.1.43.2.17.2.1.21 |
| a3ComPortVirtual mandatory This object indicates whether this port is a virtual port or
a normal port. | column | Enumeration | .1.3.6.1.4.1.43.2.17.2.1.22 |
| a3ComQueueThrottle mandatory This object specifies the maximum number of medium and low priority
packets that can be sent to the line driver each time some packets
are sent to the driver. A value of 0 means … | column | Integer32 | .1.3.6.1.4.1.43.2.17.2.1.23 |
| a3ComPortInCallerId mandatory A text string to specify the effective Incoming CallerID for the port.
This object must be successfully set for a port to use the dynamic dial
pool. It is used by the port to deci… | column | OctetString | .1.3.6.1.4.1.43.2.17.2.1.24 |
| a3ComPortCompType mandatory This object specifies the type of compression performed on this Port.
NONE indicates that the compression is disabled. HIStory indicates
that the compression is enabled and prese… | column | Enumeration | .1.3.6.1.4.1.43.2.17.2.1.25 |
| a3ComPortX25ProtID mandatory This object specifies the X25 ProtolID used when running in
Boundary Routed Mode for establishing the Virtual Circuits
over X25 Link. | column | Integer32 | .1.3.6.1.4.1.43.2.17.2.1.26 |
| a3ComPortIbmTraffic mandatory This object is used to enable or disable the SmartFiltering
of IBM Traffic mechanism on a port. Note, this only applies to
the Central Node in a boundary routing environment.
… | column | Enumeration | .1.3.6.1.4.1.43.2.17.2.1.27 |
| a3ComPortBoundaryRoute mandatory This object controls whether the Boundary Routing feature is
enabled for this port. Note: this feature only applies to
serial ports on a NB2 and will be disabled for non-serial p… | column | Enumeration | .1.3.6.1.4.1.43.2.17.2.1.3 |
| a3ComPortCosInterleave obsolete (For bridging.) The number of high-priority packets
that will be transmitted for each low-priority
packet. If the value is 0, then low-priority packets
will only be transmitted wh… | column | Integer32 | .1.3.6.1.4.1.43.2.17.2.1.5 |
| a3ComPortMacAddrFmtARP mandatory This object indicates the MAC address format used
in ARP packets sent by this port. Note, nonCanonical(2)
is allowed only on Token Ring ports. | column | Enumeration | .1.3.6.1.4.1.43.2.17.2.1.6 |
| a3ComPortMacAddrFmtIPX mandatory This determine the MAC address format used in
IPX packets sent by this port. Note, nonCanonical(2)
is allowed only on Token Ring ports. | column | Enumeration | .1.3.6.1.4.1.43.2.17.2.1.7 |
| a3ComPortMacAddrFmtXNS mandatory This determines the MAC address format used in
XNS packets sent by this port. Note, nonCanonical(2)
is allowed only on Token Ring ports. | column | Enumeration | .1.3.6.1.4.1.43.2.17.2.1.8 |
| a3ComPortPath mandatory The Path which is assigned to this port. In some cases,
one or more Paths will be assigned to a single Port. This
object will return the lowest number Path in that case.
For tho… | column | Integer32 | .1.3.6.1.4.1.43.2.17.2.1.9 |