RAD-Sonet-MIB Table View

The SONET Medium table.

prtSonetMediumEntry row .1.3.6.1.4.1.164.3.1.6.2.1.1.1

An entry in the SONET Medium table. ifIndex of the
lowest SONET layer of type sonet(39).

Indexes

No indexes recorded

Column	Syntax	OID
prtSonetMediumTimeElapsed The number of seconds that have elapsed since the beginning of the near end current error- measurement period.	Integer32 Enumerated Values: 1 notApplicable 2 none 3 proprietary 4 rip2	.1.3.6.1.4.1.164.3.1.6.2.1.1.1.1
prtSonetMediumValidIntervals The number of previous near end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complet…	Integer32 Enumerated Values: 1 notApplicable 3 proprietary 5 ppp 6 frameRelay 7 hdlc 8 lapdOverHdlc	.1.3.6.1.4.1.164.3.1.6.2.1.1.1.2
prtSonetMediumSsmRX This parameter indicates SSM RX value (quality level of clock signal). SSM (Synchronization Status Messages) octet is encoded as follows: Bit1 = '1' - indicates all octet is Not Applicable Bits 8-5 (when bit1=0): …	OctetString Enumerated Values: 1 notApplicable 2 terminal 3 linear 4 linearProtection 5 dualRing	.1.3.6.1.4.1.164.3.1.6.2.1.1.1.3
prtSonetMediumSsmTX This parameter indicates SSM TX value (quality level of clock signal). SSM (Synchronization Status Messages) octet is encoded the same as prtSonetMediumSsmRX.	OctetString Enumerated Values: 1 notApplicable 2 none 3 e1Byte 4 e2Byte	.1.3.6.1.4.1.164.3.1.6.2.1.1.1.4

The SONET Section/Line Current table.

prtSectionLineCurrentEntry row .1.3.6.1.4.1.164.3.1.6.2.1.2.1

An entry in the SONET Section/Line Current table.
ifIndex of the section/line SONET layer of IANAifType
sonet(39).

Indexes

No indexes recorded

Column	Syntax	OID
prtSonetCurrentLOS The counter associated with the number of LOS seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.2.1.1
prtSonetCurrentLOF The counter associated with the number of LOF seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.2.1.2
prtSonetCurrentLineAIS The counter associated with the number of Line AIS seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Enumerated Values: 1 notApplicable 2 standard 3 type1 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.2.1.3
prtSonetCurrentLineFERF The counter associated with the number of Line FERF seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Enumerated Values: 1 notApplicable 2 no 3 yes Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.2.1.4
prtSonetCurrentSectionBIP The counter associated with the number of Section BIP errors, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.2.1.5
prtSonetCurrentLineBIP The counter associated with the number of Line BIP errors, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.2.1.6
prtSonetCurrentLineFEBE The counter associated with the number of Line FEBE errors, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.2.1.7
prtSonetCurrentUAS The counter associated with the number of UAS encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.2.1.8
prtSonetCurrentSES The counter associated with the number of SES encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.2.1.9
prtSonetCurrentES The number of Errored Seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Constraints: range: 1-255	.1.3.6.1.4.1.164.3.1.6.2.1.2.1.10
prtSonetCurrentStatus The statuses of the current interval: 0 - O.K. 1 - The link has been switched by a redundancy mechanism. 2 - Module is in/out. 4 - Empty - card is out.	OctetString	.1.3.6.1.4.1.164.3.1.6.2.1.2.1.11
prtSonetCurrentLSV The counter associated with the number of LSV seconds (Line Symbol Violation), encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Enumerated Values: 1 notApplicable 2 disable 3 enable Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.2.1.12
prtSonetCurrentXStatus This variable indicates the Status of the interface. It contains failure state information. The variable is a bit map represented as a sum, therefore, it can represent multiple failures simultaneously. The sonetSectionL…	SNMPv2-SMIInteger32 Enumerated Values: 1 notApplicable 2 disable 3 enable Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.2.1.2.1.13
prtSonetCurrentLineRDI The counter associated with the number of Line RDI seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Constraints: range: 0-62	.1.3.6.1.4.1.164.3.1.6.2.1.2.1.14

The Section/Line Interval table.

prtSectionLineIntervalEntry row .1.3.6.1.4.1.164.3.1.6.2.1.3.1

An entry in the SONET Section/Line Interval table.
ifIndex of the section/line SONET layer of IANAifType
sonet(39).

Indexes

No indexes recorded

Column	Syntax	OID
prtSonetLineIntervalNumber A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).	Integer32 Enumerated Values: 1 notApplicable 2 nulls 3 spaces	.1.3.6.1.4.1.164.3.1.6.2.1.3.1.1
prtSonetIntervalLOS The counter associated with the number of LOS seconds , encountered by a SONET interface in one of the previous 15 minute intervals.	SNMPv2-SMIGauge32 Enumerated Values: 1 notApplicable 2 disable 3 enable Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.3.1.2
prtSonetIntervalLOF The counter associated with the number of LOF seconds, encountered by a SONET interface in one of the previous 15 minute, intervals.	SNMPv2-SMIGauge32 Enumerated Values: 1 notApplicable 2 pos 3 clearchannel 4 channelized 5 vc1x Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.3.1.3
prtSonetIntervalLineAIS The counter associated with the number of Line AIS seconds, encountered by a SONET/SDH interface in one of individual 15 minute, intervals.	SNMPv2-SMIGauge32 Enumerated Values: 1 notApplicable 2 b16 3 b64 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.3.1.4
prtSonetIntervalLineFERF The counter associated with the number of Line FERF seconds, encountered by a SONET/SDH interface in one of the previous 15 minute intervals.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.3.1.5
prtSonetIntervalSectionBIP The counter associated with the number of Section BIP errors, encountered by a SONET/SDH interface in one of the previous 15 minute intervals.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.3.1.6
prtSonetIntervalLineBIP The counter associated with the number of Line BIP errors, encountered by a SONET/SDH interface in one of the previous 15 minute intervals.	SNMPv2-SMIGauge32 Constraints: range: 1-255	.1.3.6.1.4.1.164.3.1.6.2.1.3.1.7
prtSonetIntervalLineFEBE The counter associated with the number of Line FEBE errors, encountered by a SONET/SDH interface in one of the previous 15 minute intervals.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.3.1.8
prtSonetIntervalUAS The counter associated with the number of UnAvailable Seconds encountered by a SONET/SDH interface in one of the previous 15 minute intervals.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.3.1.9
prtSonetIntervalSES The counter associated with the number of Severely Errored Seconds encountered by a SONET/SDH interface in one of the previous 15 minute intervals.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.3.1.10
prtSonetIntervalES The number of Errored Seconds encountered by a SONET/SDH interface in one of the previous 15 minute intervals.	SNMPv2-SMIGauge32 Enumerated Values: 2 connect 3 bypass Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.3.1.11
prtSonetIntervalStatus The statuses of the current interval: 0 - O.K. 1 - The link has been switched by a redundancy mechanism. 2 - Module is in/out. 4 - Empty - card is out.	OctetString Enumerated Values: 1 notApplicable 2 addAndDrop 3 add	.1.3.6.1.4.1.164.3.1.6.2.1.3.1.12
prtSonetIntervalLSV The counter associated with the number of LSV seconds (Line Symbol Violation), encountered by a SONET/SDH interface in one of the previous 15 minute intervals.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.3.1.13
prtSonetIntervalLineRDI The counter associated with the number of Line RDI seconds encountered by a SONET/SDH interface in one of the previous 15 minute intervals.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.3.1.14
prtSonetIntervalSectionTimeElapsed The object contains duration in seconds of the interval measurement period. The partial second is counted.	Integer32	.1.3.6.1.4.1.164.3.1.6.2.1.3.1.15
prtSonetIntervalFC The counter associated with the number of Failure Counts encountered by a SONET interface in one of the previous 15 minute intervals. It is not defined at the Section level.	PerfHist-TC-MIBPerfIntervalCount Constraints: range: 1-255	.1.3.6.1.4.1.164.3.1.6.2.1.3.1.16
prtSonetIntervalFarEndFC The counter associated with the number of Failure Counts encountered by a Far End SONET interface in one of the previous 15 minute intervals. It is not defined at the Section level.	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.3.1.6.2.1.3.1.17

The SONET Path Current table.

prtPathCurrentEntry row .1.3.6.1.4.1.164.3.1.6.2.1.4.1

An entry in the SONET Path Current table.
ifIndex of the Path SONET layer of IANAifType
sonetPath(50).

Indexes

No indexes recorded

Column	Syntax	OID
prtSonetCurrentPathAIS The counter associated with the number of Path AIS seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Constraints: range: 0-84	.1.3.6.1.4.1.164.3.1.6.2.1.4.1.1
prtSonetCurrentPathFERF The counter associated with the number of Path FERF seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Enumerated Values: 1 notApplicable 2 lcasNotActive 3 lcasActive Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.4.1.2
prtSonetCurrentLOP The counter associated with the number LOP seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Enumerated Values: 1 notApplicable 2 laps 3 lapf 4 gfp Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.4.1.3
prtSonetCurrentSLM The counter associated with the number of SLM seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.4.1.4
prtSonetCurrentLOC The counter associated with the number of LOC seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Enumerated Values: 1 notApplicable 2 no 3 yes Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.4.1.5
prtSonetCurrentPathBIP The counter associated with the number of Path BIP errors, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Constraints: range: 0-255	.1.3.6.1.4.1.164.3.1.6.2.1.4.1.6
prtSonetCurrentPathFEBE The counter associated with the number of Path FEBE errors, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Enumerated Values: 1 notApplicable 2 no 3 yes Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.4.1.7
prtSonetPathCurrentStatus This variable indicates the Status of the interface. It contains failure state information. The variable is a bit map represented as a sum, therefore, it can represent multiple failures simultaneously. The sonetPathNoDe…	SNMPv2-SMIInteger32 Constraints: range: 1-1	.1.3.6.1.4.1.164.3.1.6.2.1.4.1.8
prtSonetCurrentPathRDI The counter associated with the number of Path RDI seconds, encountered by a SONET interface in the current 15 minute interval.	SNMPv2-SMIGauge32 Constraints: range: 0-83	.1.3.6.1.4.1.164.3.1.6.2.1.4.1.9

The Path Interval table.

prtPathIntervalEntry row .1.3.6.1.4.1.164.3.1.6.2.1.5.1

An entry in the SONET Path Interval table.

Indexes

No indexes recorded

Column	Syntax	OID
prtSonetPathIntervalNumber A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid).	Integer32 Enumerated Values: 1 notApplicable 2 managementOnly 3 dataOnly 4 mixed	.1.3.6.1.4.1.164.3.1.6.2.1.5.1.1
prtSonetIntervalPathAIS The counter associated with the number of Path AIS seconds, encountered by a SONET Path interface in one of the previous 96, individual 15 minute intervals.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.5.1.2
prtSonetIntervalPathFERF The counter associated with the number of Path FERF seconds encountered by a SONET Path interface in one of the previous 96, individual 15 minute intervals.	SNMPv2-SMIGauge32 Enumerated Values: 1 notApplicable 2 disabled 3 enabeld Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.5.1.3
prtSonetIntervalLOP The counter associated with the number of LOP seconds encountered by a SONET Path interface in one of the previous 96, individual 15 minute intervals.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.5.1.4
prtSonetIntervalSLM The counter associated with the number of SLM seconds, encountered by a SONET Path interface in one of the previous 96, individual 15 minute intervals.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.5.1.5
prtSonetIntervalLOC The counter associated with the number of LOC seconds, encountered by a SONET Path interface in one of the previous 96, individual 15 minute intervals.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.5.1.6
prtSonetIntervalPathBIP The counter associated with the number of Path BIP errors, encountered by a SONET Path interface in one of the previous 96, individual 15 minute intervals.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.5.1.7
prtSonetIntervalPathFEBE The counter associated with the number of Path FEBE errors, encountered by a SONET Path interface in one of the previous 96, individual 15 minute intervals.	SNMPv2-SMIGauge32 Constraints: range: 1-255	.1.3.6.1.4.1.164.3.1.6.2.1.5.1.8
prtSonetIntervalPathRDI The counter associated with the number of Path RDI seconds, encountered by a SONET Path interface in one of the previous 96, individual 15 minute intervals.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.5.1.9

The Virtual Interface Current table.

virtualIfCurrentEntry row .1.3.6.1.4.1.164.3.1.6.2.1.6.1.1

An entry in the Virtual Interface Current table.

Indexes

No indexes recorded

Column	Syntax	OID
virtualIfCurrentMinActiveVC This object holds the minimum number of active virtual containers (VCs) of the Virtual Concatenation Group in the current 15-minute interval.	Integer32	.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.1
virtualIfCurrentMaxActiveVC This object holds the maximum number of active virtual containers (VCs) of the Virtual Concatenation Group in the current 15-minute interval.	Integer32	.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.2
virtualIfCurrentRxFrames This counter is associated with the number of frames received from STS-3/STM-1 by a Virtual Interface in the current 15-minute interval.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.3
virtualIfCurrentTxFrames This counter is associated with the number of frames transmitted to STS-3/STM-1 by a Virtual Interface in the current 15-minute interval.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.4
virtualIfCurrentRxAbortFrames The counter associated with the number of Received Aborted frames encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount Constraints: range: 1-255	.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.5
virtualIfCurrentTxAbortFrames The counter associated with the number of Transmitted Aborted frames encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.6
virtualIfCurrentMinLengthViolation This counter is associated with the number of Rx payload Min Length Violation frames encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount Enumerated Values: 1 notApplicable 2 fcsEnable 3 fcsDisable	.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.7
virtualIfCurrentMaxLengthViolation This counter is associated with the number of Rx payload Max Length Violation frames encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.8
virtualIfCurrentFcsError The counter is associated with the number of Frame Check Sequence errors encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.9
virtualIfCurrentByteDestuffingViolation The counter associated with the number of Byte De-stuffing Violations encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount Constraints: range: 1-255	.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.10
virtualIfCurrentAdressMismatch The counter associated with the number of Adress Mismatch encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.11
virtualIfCurrentControlMismatch The counter associated with the number of Control Mismatch encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.12
virtualIfCurrentActiveVC This object holds the number of active virtual containers (VCs) of the Virtual Concatenation Group in the current 15-minute interval.	Integer32	.1.3.6.1.4.1.164.3.1.6.2.1.6.1.1.13

The Virtual Interface Interval table.

virtualIfIntervalEntry row .1.3.6.1.4.1.164.3.1.6.2.1.6.2.1

An entry in the Virtual Interface Interval table.

Indexes

No indexes recorded

Column	Syntax	OID
virtualIfIntervalNumber A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is …	Integer32	.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.1
virtualIfIntervalMinActiveVC This object holds the minimum number of active virtual containers (VCs) of the Virtual Concatenation Group, in a particular 15-minute interval in the past 24 hours.	Integer32	.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.2
virtualIfIntervalMaxActiveVC This object holds the maximum number of active virtual containers (VCs) of the Virtual Concatenation Group, in a particular 15-minute interval in the past 24 hours.	Integer32 Enumerated Values: 1 notApplicable 2 rx 3 tx 4 both	.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.3
virtualIfIntervalRxFrames This counter is associated with the number of frames received from STS-3/STM-1 by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	SNMPv2-SMICounter32 Enumerated Values: 1 notApplicable 2 tu2 3 tu3 4 tu11 5 tu12 6 tuFour4c 7 sts12c Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.4
virtualIfIntervalTxFrames This counter is associated with the number of frames transmitted to STS-3/STM-1 by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	SNMPv2-SMICounter32 Enumerated Values: 1 notApplicable 2 addAndDrop 3 bypass Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.5
virtualIfIntervalRxAbortFrames This counter is associated with the number of Received Abort frames encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.6
virtualIfIntervalTxAbortFrames This counter is associated with the number of Transmitted Abort frames encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.7
virtualIfIntervalMinLengthViolation This counter is associated with the number of Rx payload Min Length Violation frames encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount Constraints: range: 0-62	.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.8
virtualIfIntervalMaxLengthViolation This counter is associated with the number of Rx payload Max Length Violation frames encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount Constraints: range: 1-1	.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.9
virtualIfIntervalFcsError This counter is associated with the number of Frame Check Sequence errors encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount Enumerated Values: 1 notApplicable 2 fixed 3 add 4 norm 5 eos 6 idle 7 dnu	.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.10
virtualIfIntervalByteDestuffingViolation This counter is associated with the number of Byte De-stuffing Violations encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount Enumerated Values: 1 notApplicable 2 fixed 3 add 4 norm 5 eos 6 idle 7 dnu	.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.11
virtualIfIntervalAdressMismatch This counter is associated with the number of Address Mismatch encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.12
virtualIfIntervalControlMismatch This counter is associated with the number of Control mismatch encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.13
virtualIfIntervalBelowMinThreshold This counter is associated with the number of seconds that number of active VCs was below minimum threshold defined by vcGroupCnfgNoOfVCs, encountered by Virtual Interface in a particular 15-minute interval in the past …	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.2.1.14

The Virtual Interface LAPS Current table.

virtualIfLAPSCurrentEntry row .1.3.6.1.4.1.164.3.1.6.2.1.6.3.1

An entry in the Virtual Interface
LAPS Current table.

Indexes

No indexes recorded

Column	Syntax	OID
virtualIfLAPSCurrentSapiMismatch This counter is associated with the number of received SAPI field mismatch encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount Enumerated Values: 1 notApplicable 2 off 3 on	.1.3.6.1.4.1.164.3.1.6.2.1.6.3.1.1

The Virtual Interface LAPS table.

virtualIfLAPSIntervalEntry row .1.3.6.1.4.1.164.3.1.6.2.1.6.4.1

An entry in the Virtual Interface
LAPS Interval table.

Indexes

No indexes recorded

Column	Syntax	OID
virtualIfLAPSIntervalSapiMismatch This counter is associated with the number of received SAPI field mismatch encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.4.1.1

The Virtual Interface LAPF Current table.

virtualIfLAPFCurrentEntry row .1.3.6.1.4.1.164.3.1.6.2.1.6.5.1

An entry in the Virtual Interface
LAPF Current table.

Indexes

No indexes recorded

Column	Syntax	OID
virtualIfLAPFCurrentNlpidMismatch This counter is associated with the number of received NLPID field mismatch encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.5.1.1
virtualIfLAPFCurrentOuiMismatch This counter is associated with the number of received OUI field mismatch encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.5.1.2
virtualIfLAPFCurrentPidMismatch This counter is associated with the number of received PID field mismatch encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.5.1.3
virtualIfLAPFCurrentDlciMismatch This counter is associated with the number of received DLCI field mismatch encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.5.1.4
virtualIfLAPFCurrentMacRxFrames This counter is associated with the number of frames received from LAN by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.5.1.5
virtualIfLAPFCurrentMacTxFrames This counter is associated with the number of frames transmitted to LAN by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount Enumerated Values: 2 working 3 protection	.1.3.6.1.4.1.164.3.1.6.2.1.6.5.1.6

The Virtual Interface LAPF Interval table.

virtualIfLAPFIntervalEntry row .1.3.6.1.4.1.164.3.1.6.2.1.6.6.1

An entry in the Virtual Interface Interval table.

Indexes

No indexes recorded

Column	Syntax	OID
virtualIfLAPFIntervalNlpidMismatch This counter is associated with the number of received NLPID field mismatch encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount Enumerated Values: 2 off 3 on	.1.3.6.1.4.1.164.3.1.6.2.1.6.6.1.1
virtualIfLAPFIntervalOuiMismatch This counter is associated with the number of received OUI field mismatch encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount Enumerated Values: 1 noOp 2 clear 3 forcedSwitch 4 lockout	.1.3.6.1.4.1.164.3.1.6.2.1.6.6.1.2
virtualIfLAPFIntervalPidMismatch This counter is associated with the number of received PID field mismatch encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount Enumerated Values: 2 no 3 yes	.1.3.6.1.4.1.164.3.1.6.2.1.6.6.1.3
virtualIfLAPFIntervalDlciMismatch This counter is associated with the number of received DLCI field mismatch by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.6.1.4
virtualIfLAPFIntervalMacRxFrames This counter is associated with the number of frames received from LAN by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.6.1.5
virtualIfLAPFIntervalMacTxFrames This counter is associated with the number of frames transmitted to LAN encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.6.1.6

The Virtual Interface GFP Current table.

virtualIfGFPCurrentEntry row .1.3.6.1.4.1.164.3.1.6.2.1.6.7.1

An entry in the Virtual Interface
GFP Current table.

Indexes

IF-MIBifIndex

Column	Syntax	OID
virtualIfGFPCurrentIdleFrameError This counter is associated with the number of received GFP IDLE frames that are detected to be in error, encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.1
virtualIfGFPCurrentCHecSbError This counter is associated with the number of received GFP frames that are detected to have single-bit errors in the Core header (i.e. cHEC field) only, encountered by a Virtual Interface in the current 15-minute in…	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.2
virtualIfGFPCurrentPtiMismatch This counter is associated with the number of rreceived GFP frames that are detected with a mismatch on the PTI field (i.e. value of PTI is not equal to Client Data or Management frame), encountered by a Virtual Inte…	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.3
virtualIfGFPCurrentExiMismatch This counter is associated with the number of received GFP frames that are detected with a mismatch on the EXI field (i.e. value of EXI is not equal to NULL or LINEAR modes), encountered by a Virtual Interface in t…	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.4
virtualIfGFPCurrentUpiMismatch This counter is associated with the number of received GFP frames that are detected with a mismatch on the UPI field (i.e. value of EXI is not equal to 00000001), encountered by a Virtual Interface in th…	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.5
virtualIfGFPCurrentTHecSbError This counter is associated with the number of received GFP frames that are detected to only have single-bit errors in the Type header (i.e. tHEC field), encountered by a Virtual Interface in the current 15-minute int…	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.6
virtualIfGFPCurrentTHecMbError This counter is associated with the number of received GFP frames that are detected to only have multi-bit errors in the Type header (i.e. tHEC field), encountered by a Virtual Interface in the current 15-mi…	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.7
virtualIfGFPCurrentCidMismatch This counter is associated with the number of received GFP frames that are detected to have a mismatch/unsupported value in the CID field only, encountered by a Virtual Interface in the current 15-minute interval.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.8
virtualIfGFPCurrentEHecSbError This counter is associated with the number of received GFP frames that are detected to only have single-bit errors in the Extension header (i.e. eHEC field), encountered by a Virtual Interface in the current 15-min…	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.9
virtualIfGFPCurrentEHecMbError This counter is associated with the number of received GFP frames that are detected to only have single-bit errors in the Extension header (i.e. eHEC field), encountered by a Virtual Interface in the current 15-minu…	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.7.1.10

The Virtual Interface GFP Interval table.

virtualIfGFPIntervalEntry row .1.3.6.1.4.1.164.3.1.6.2.1.6.8.1

An entry in the Virtual Interface
GFP Interval table.

Indexes

No indexes recorded

Column	Syntax	OID
virtualIfGFPIntervalIdleFrameError This counter is associated with the number of received GFP IDLE frames that are detected to be in error, encountered by a Virtual Interface in a particular 15-minute interval in the past 24 hours.	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.1
virtualIfGFPIntervalCHecSbError This counter is associated with the number of received GFP frames that are detected to have single-bit errors in the Core header (i.e. cHEC field) only, encountered by a Virtual Interface in a particular 15-minute int…	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.2
virtualIfGFPIntervalPtiMismatch This counter is associated with the number of rreceived GFP frames that are detected with a mismatch on the PTI field (i.e. value of PTI is not equal to Client Data or Management frame), encountered by a Virtual Inter…	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.3
virtualIfGFPIntervalExiMismatch This counter is associated with the number of received GFP frames that are detected with a mismatch on the EXI field (i.e. value of EXI is not equal to NULL or LINEAR modes), encountered by a Virtual Inter…	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.4
virtualIfGFPIntervalUpiMismatch This counter is associated with the number of received GFP frames that are detected with a mismatch on the UPI field (i.e. value of EXI is not equal to 00000001), encountered by a Virtual Interface in a particular 15…	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.5
virtualIfGFPIntervalTHecSbError This counter is associated with the number of received GFP frames that are detected to only have single-bit errors in the Type header (i.e. tHEC field), encountered by a Virtual Interface in a particular 15-minute inte…	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.6
virtualIfGFPIntervalTHecMbError This counter is associated withthe number of received GFP frames that are detected to only have multi-bit errors in the Type header (i.e. tHEC field), encountered by a Virtual Interface in a particular 15-minute interv…	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.7
virtualIfGFPIntervalCidMismatch This counter is associated with the number of received GFP frames that are detected to have a mismatch/unsupported value in the CID field only, encountered by a Virtual Interface in a particular 15-minute interval in …	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.8
virtualIfGFPIntervalEHecSbError This counter is associated with the number of received GFP frames that are detected to only have single-bit errors in the Extension header (i.e. eHEC field), encountered by a Virtual Interface in a particula…	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.9
virtualIfGFPIntervalEHecMbError This counter is associated with the the number of received GFP frames that are detected to only have multi-bit errors in the Extension header (i.e. eHEC field), encountered by a Virtual Interface in a particular 15-mi…	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.3.1.6.2.1.6.8.1.10

Sonet/SDH general port configuration table.

prtSonetGenEntry row .1.3.6.1.4.1.164.3.1.6.2.2.1.1.1

An entry in the Sonet/SDH general port configuration table.

Indexes

No indexes recorded

Column	Syntax	OID
prtSonetGenCnfgIdx This object indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For products that support several configurations, Set can be performed only to the Temporary Config (=255…	Integer32	.1.3.6.1.4.1.164.3.1.6.2.2.1.1.1.1
prtSonetGenIdx This object indicates a unique port or interface number. For numbering, see product's spec. For some products, the numbering can equal ifIndex.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.2.2.1.1.1.2
prtSonetGenSdThreshold SD=Signal Degraded Threshold. Units: [10E-]. The threshold is 10E-x relative to the frequency of the data flow. x=3, 4, 5, 6, 7, 8, 9. n3= 10E-3 n4= 10E-4 n5= 10E-5 n6= 10E-6 n7= 10E-7 n8= 10E-8 n9= 10E-9 .	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.1.1.1.3
prtSonetGenEedThreshold EED=Excessive Error Defect Threshold. Units: [10E-]. The threshold is 10E-x relative to the frequency of the data flow. x=3, 4, 5, 6, 7, 8, 9. n3= 10E-3 n4= 10E-4 n5= 10E-5 n6= 10E-6 n7= 10E-7 n8= 10E-8 n9= 10E-9 .	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.1.1.1.4
prtSonetGenBerEnable Controls the activation of the Line Ber (Bit Error Rate), means whether SD and EED threshold parameters will be enabled.	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.1.1.1.5

Sonet/SDH STM-1 port configuration table.

prtSonetStm1Entry row .1.3.6.1.4.1.164.3.1.6.2.2.2.1.1

An entry in the Sonet/SDH STM-1 port configuration table.

Indexes

No indexes recorded

Column	Syntax	OID
prtSonetStm1CnfgIdx This object indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For products that support several configurations, Set can be performed only to the Temporary Config (=255…	Integer32	.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.1
prtSonetStm1Idx This object indicates a unique port or interface number. For numbering, see product's spec. For some products, the numbering can equal ifIndex.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.2
prtSonetStm1ClockSrc Clock Source of the STM-1 port. lbt = Loop Back Timing.	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.3
prtSonetStm1DccMode DCC Mode. DCC=Data Communication Channel. d1ToD3 = D1-D3 bytes are used (RS=Regeneration Section). d4ToD12= D4-D12 bytes are used (MS=Multiplexing Section). d1.... d12 enable user to select single DCC byte	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.4
prtSonetStm1RoutingProt Routing Protocol.	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.5
prtSonetStm1MngProt Management Protocol over DCC: Proprietary, PPP, Frame Relay, HDLC or LAPD over HDLC . ppp = according to STD-51 ( rfc1661/1662)	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.6
prtSonetStm1OperationalMode Operational Mode. linear - cannot be selected when there is Redundancy between the STM-1 ports.	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.7
prtSonetStm1VoiceChannel This parameter enable user to select whether voice channel will be transferred using E1 byte, E2 Byte, or not at all.	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.8
prtSonetStm1OutputRate This parameter indicates the output rate in cells/sec, which is supported per port.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.9
prtSonetStm1S1ProtocolClock This parameter allows user to select whether to enable use of Remote Side Clock according to the Protocol passed on S1 Bit.	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.10
prtSonetStm1GatewayRingSubnetAddress This parameter defines subnet for static routing, together with prtSonetStm1GatewayRingSubnetMask	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.11
prtSonetStm1GatewayRingSubnetMask This parameter defines subnet for static routing, together with prtSonetStm1GatewayRingSubnetAddress	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.12
prtSonetStm1MngProtDeviationType This parameter is used in conjunction with prtSonetStm1MngProt to define management protocol used & type of deviation (if exist) from standard. Standard = no deviation from standard protocol Type1 = PPP without se…	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.13
prtSonetStm1MngSameIpAsHost This parameter indicates whether IP address used for management is same as the device IP address	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.14
prtSonetStm1MngIpAddress This parameter defines IP address for DCC management for this link, together with prtSonetStm1MngIpSubnetMask. This parameter is applicable only if prtSonetStm1MngSameIpAsHost=no.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.15
prtSonetStm1MngIpSubnetMask This parameter defines IP subnet mask for DCC management for this link, together with prtSonetStm1MngIpAddress This parameter is applicable only if prtSonetStm1MngSameIp=no	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.16
prtSonetStm1MngDefaultGateway This parameter defines default Gateway address for DCC management for this link. This parameter is applicable only if prtSonetStm1MngSameIp=no	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.164.3.1.6.2.2.2.1.1.17

Sonet/SDH VC port configuration table.

prtSonetVcEntry row .1.3.6.1.4.1.164.3.1.6.2.2.3.1.1

An entry in the Sonet/SDH VC port configuration table.

Indexes

No indexes recorded

Column	Syntax	OID
prtSonetVcCnfgIdx This object indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For products that support several configurations, Set can be performed only to the Temporary Config (=255…	Integer32	.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.1
prtSonetVcIdx This object indicates a unique port or interface number. For numbering, see product's spec. For some products, the numbering can equal ifIndex.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.2
prtSonetVcJTxPathTraceEnable Enable/Disable transmitting Jy Path Trace. y = 0, 1, 2: J0 - for SDH/SONET layer J1 - for VC-4 layer J2 - for VC-12 layer. The default value is 'enable' (3).	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.3
prtSonetVcJRxPathTraceEnable Enable/Disable checking Jy Path Trace. y = 0, 1, 2: J0 - for SDH/SONET layer J1 - for VC-4 layer J2 - for VC-12 layer.	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.4
prtSonetVcJPathTrace Jy Path Trace. y = 0, 1, 2: J0 - for SDH/SONET layer J1 - for VC-4 layer J2 - for VC-12 layer. This object is applicable only if one of the previous 2 objects is 'enable'. The J0 SDH default value is 0x00. The J0 SONET…	OctetStringr/w	.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.5
prtSonetVcConnect Connect VCn (n - 11,12,2,3,4) port (yes/no).	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.6
prtSonetVcSignalLabel Signal Label. For VC-3: The SONET standard defines the C2 byte as the path signal label. The purpose of this byte is to communicate the payload type being encapsulated by the SONET Framing OverHead. It allows a single i…	OctetStringr/w	.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.7
prtSonetVcPathTracePadding Padding character will pad prtSonetVcJPathTrace string to fill required number of characters. The default value is nulls (2) '0x00'.	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.8
prtSonetVcPayloadBlockOnPathTrace Block payload on this VC upon PathTrace (TIM).	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.9
prtSonetVcPayloadType Payload type, applicable for STS-1/TUG-3 layer. vc1x = vc12 or vc11 for SDH, VT1.5, VT2 for SONET. clear channel - complete TUG-3 or STS-1 For Egate-100: POS (Packets over Sonet) configuration is valid per STM1/OC3…	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.10
prtSonetVcPathTraceSize Path Trace Size in Bytes - 16 or 64.	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.3.1.1.11

The write operation into the Table's Objects is valid only
for the TmpCnfg entry (Scratch).

prtSonetTuEntry row .1.3.6.1.4.1.164.3.1.6.2.2.3.2.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
prtSonetTuCnfgIdx This object indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For products that support several configurations, Set can be performed only to the Temporary Config (=255…	Integer32	.1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.1
prtSonetTuPrtIdx This object indicates a unique port or interface number. For port numbering, see product's spec. For some products, the numbering can equal ifIndex.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.2
prtSonetTuIdx This object indicates a unique TU (Tributary Unit) within VC-4. The valid TUs are 1..63.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.3
prtSonetTuConPrtIdx This object indicates the connected port, when prtSonetTuType=connect. For port numbering, see product's spec. For some products, the numbering can equal ifIndex. notApplicable - will be indicated as 100.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.4
prtSonetTuType The type of TU (Tributary Unit). connect - connected to one of the E1 ports. bypass - bypassed to the other VC4 port. TUs that are not connected or bypassed, will not exist in this table.	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.5
prtSonetTuMode TU Mode of connection. addAndDrop - Add & Drop add - Add (TU receives from the E1 ports).	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.6
prtSonetTuRowStatus Creation/Deletion of rows in the table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.164.3.1.6.2.2.3.2.1.7

The Virtual Concatenation Group configuration table.

vcGroupCnfgEntry row .1.3.6.1.4.1.164.3.1.6.2.2.4.1.1

An entry in the Virtual Concatenation Group
configuration table.

Indexes

No indexes recorded

Column	Syntax	OID
vcGroupCnfgIdx This object indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For products that support several configurations, Set can be performed only to the Temporary Config (=255…	Integer32	.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.1
vcGroupCnfgNumber Virtual Concatenation Group Number. For FCD-155 up to eight groups are defined valid values are 1..8. For MP-4100, group ifIndex is used.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.2
vcGroupCnfgRowStatus Creation/Deletion of rows in the table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.3
vcGroupCnfgVcType User may select type of SDH Virtual Containers (VC) (SONET Virtual Tributaries VT ) to be concatenated in this Virtual Concatenation Group. For SDH, values 2,3,4 and 8 are valid. For SONET, values 5, 6,7 are valid.	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.4
vcGroupCnfgNoOfVCs User may select number of Virtual Containers (VC) (SONET Virtual Tributaries VT ) to be concatenated in this Virtual Concatenation Group. Valid range for this number depends on type VC selected by vcGroupCnfgVCType For…	Integer32r/w	.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.5
vcGroupCnfgLCAS This object controls Link Capacity Adjustment Scheme (LCAS) activation.	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.6
vcGroupCnfgEncapsulation This object enables user to select encapsulation method.	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.7
vcGroupCnfgGroupIfIndex The ifIndex assigend to this group.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.8
vcGroupCnfgRip2 This object controls RIP 2. User may select to send RIP 2 message over selected group or not	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.9
vcGroupCnfgGfpChId Generic Framing Procedure (GFP) Channel ID, Valid only when vcGroupCnfgEncapsulation = gfp (4) Valid values are 0x00 - oxFF (hex)	Integer32r/w	.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.10
vcGroupCnfgK4 This object controls whether K4 byte (of Line Overhead) is used as an indication for virtual concatenation (VCAT). This object is applicable, when VCG includes only a single Virtual Container (VC) (or SONET VT)	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.11
vcGroupCnfgExSignalLabel Extended Signal Label. Relevant only when vcGroupCnfgK4 = yes(3). Agents that do not support this feature will send SIZE 0.	OctetStringr/w	.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.12
vcGroupCnfgLcasMinNoOfVCs Minimum number of VC's to declare alarm, in LCAS mode. Applicable only when LCAS is active (vcGroupCnfgLCAS =lcasActive) 1...63 for SDH, 1...84 for SONET 0= not applicable.	Integer32r/w	.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.13
vcGroupCnfgLcasStatus This object summarize LCAS states of all VCs in VCG: belowMinNoOfVCs - Number of VCs in Norm state is less than the minimum number of VCs (indicated by vcGroupCnfgLc…	Enumeration	.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.14
vcGroupCnfgMappingMode This object define Path Protection mode for VCG. Auto - the entire mapping for Virtual Concatenation Group x is copied automatically by agent for the protection group to same TUs on the other SONET/SDH link which resi…	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.15
vcGroupCnfgTrafficType This object allows to select traffic type for specific VCG.	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.16
vcGroupCnfgGroupName Virtual Concatenation Group (VCG) Name. String length is limited to 15 characters.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.17
vcGroupCnfgLoopDetection VCAT Loop detecetion enabled.	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.18
vcGroupCnfgLcasWaitToRestore Time duration (in milliseconds units) waited after errors on channel stopped, before channel is reused.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.19
vcGroupCnfgLcasHoldOff Time duration (in milliseconds units) in which errors on channel are disregarded. (Threshold)	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.2.4.1.1.20

The Virtual Concatenation Group GFP Mux configuration table.

vcgGfpMuxCnfgEntry row .1.3.6.1.4.1.164.3.1.6.2.2.4.2.1

An entry in the Virtual Concatenation Group GFP Mux
configuration table.

Indexes

No indexes recorded

Column	Syntax	OID
vcgGfpMuxCnfgIdx This object indicates the Index of the configuration being accessed. Index of 255 relates to the Temporary (Scratch) coninguration. For products that support several configurations, Set can be performed only to the Temp…	Integer32	.1.3.6.1.4.1.164.3.1.6.2.2.4.2.1.1
vcgGfpMuxCnfgMuxNumber Virtual Concatenation Group GFP Mux Number. Refer to device specification for definition of - maximum number of GFP-mux. - concatenation of Slot and GFP mux number.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.2.2.4.2.1.2
vcgGfpMuxCnfgRowStatus Creation/Deletion of rows in the table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.164.3.1.6.2.2.4.2.1.3
vcgGfpMuxCnfgMuxName Virtual Concatenation Group, GFP Mux name.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.164.3.1.6.2.2.4.2.1.4
vcgGfpMuxCnfgPrimeGroup Index of Virtual Concatenation Group used as Primary for the GFP mux created for FCD 155 up to 8 Virtual Concatenation Group are defined: 1 -> Virtual Concatenation Group 1 2 -> Virtual Concatenation Group 2 3 -> V…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.2.2.4.2.1.5
vcgGfpMuxCnfgGrpBwAlloc This object indicates the allocated bandwidth (BW) to each Virtual Concatenation Group (VCG). Each nibble indicates BW percentage, in 12.5% steps, assigned to a group. For FCD-155, there may be 4 or 8…	OctetStringr/w	.1.3.6.1.4.1.164.3.1.6.2.2.4.2.1.6

Sonet/SDH general port configuration table.

virtualIfGenEntry row .1.3.6.1.4.1.164.3.1.6.2.2.5.1.1

An entry in the Sonet/SDH general port configuration table.

Indexes

No indexes recorded

Column	Syntax	OID
virtualIfGenCnfgIdx This object indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For products that support several configurations, Set can be performed only to the Temporary Config (=255…	Integer32	.1.3.6.1.4.1.164.3.1.6.2.2.5.1.1.1
virtualIfGenIdx This object indicates a unique port or interface number. For numbering, see product's spec. For some products, the numbering can equal ifIndex.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.2.2.5.1.1.2
virtualIfGenFrameFormat The frame format. fcsEnabe = Frame will be sent with the FCS bits. fcsDisable = Frame will be sent without the FCS bits .	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.2.5.1.1.3

The write operation into the Table's Objects is valid only
for the TmpCnfg entry (Scratch).

prtSonetXConnectEntry row .1.3.6.1.4.1.164.3.1.6.2.3.1.1

An entry in table.

Indexes

No indexes recorded

Column	Syntax	OID
prtSonetXConnectCnfgIdx This object indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For products that support several configurations, Set can be performed only to the Temporary Config (=255…	Integer32	.1.3.6.1.4.1.164.3.1.6.2.3.1.1.1
prtSonetXConnectPrtIdx This object indicates a unique port or interface number. For port numbering, see product's spec. For some products, the numbering can equal ifIndex.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.2.3.1.1.2
prtSonetXConnectConPrtIdx This object indicates the connected port. For port numbering, see product's spec. For some products, the numbering can equal ifIndex. notApplicable - will be indicated as 255.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.2.3.1.1.3
prtSonetXConnectAUGIdx This object indicates an AUG (Administrative Unit Group) within STM-N. The valid AUGs values are: 1 for STM-1 1...4 for STM-4, 1..16 for STM-16 and 1..64 for STM-64 (STM-64) 255 designates NA.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.2.3.1.1.4
prtSonetXConnectTUG3Idx This object indicates a TUG-3 (Tributary Unit Group 3) within VC-4. The valid TUG3s are values are 1..3. and 255 which designates NA	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.2.3.1.1.5
prtSonetXConnectTUG2Idx This object indicates a TUG2 (Tributary Unit Group 2 ) within VC-3. The valid TUG2's values are 1..7 and 255 which designates NA	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.2.3.1.1.6
prtSonetXConnectTUnIdx This object indicates a TUn within TUG-2 or TUG-3 (Tributary Unit n, where n is 2, 12 or 11 within TUG-2, or 3 within TUG-3) valid values are 1 for TU-2 1 for TU-3 1..4 for TU-11 1..3 for TU-12 …	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.2.3.1.1.7
prtSonetXConnectRowStatus Creation/Deletion of rows in the table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.164.3.1.6.2.3.1.1.8
prtSonetXConnectDirection TU direction of connection. rx=Drop tx=Add both = Add & Drop	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.3.1.1.9
prtSonetXConnectTuNumber This object indicates which TU is used in prtSonetXConnectTUnIdx	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.3.1.1.10
prtSonetXConnectMode TU Mode of connection. addAndDrop - Add & Drop bypass - bypassed to the other VC4 port.	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.3.1.1.11

VC Status Table

prtSonetVcStatEntry row .1.3.6.1.4.1.164.3.1.6.2.4.1.1

An entry in the VC status Table.

Indexes

No indexes recorded

Column	Syntax	OID
prtSonetVcRxJPathTrace Jy Path Trace value received from network. y=1, 2: J1 - for VC-4 layer J2 - for VC-12 layer.	OctetString	.1.3.6.1.4.1.164.3.1.6.2.4.1.1.1
prtSonetVcRxSignalLabel Signal Label received from network. For VC-3: The SONET standard defines the C2 byte as the path signal label. The purpose of this byte is to communicate the payload type being encapsulated by the SONET Framing OverHe…	OctetString	.1.3.6.1.4.1.164.3.1.6.2.4.1.1.2
prtSonetVcLcasSourceState Fixed - This is an indication that this end uses fixed bandwidth (non-LCAS mode) Add - This member is about to be added to the group Norm - Normal transmission. EOS - E…	Enumeration	.1.3.6.1.4.1.164.3.1.6.2.4.1.1.3
prtSonetVcLcasSinkState Fixed - This is an indication that this end uses fixed bandwidth (non-LCAS mode) Add - This member is about to be added to the group Norm - Normal transmission. EOS - E…	Enumeration	.1.3.6.1.4.1.164.3.1.6.2.4.1.1.4
prtSonetVcStatus This variable indicates the Status of the interface. It contains failure state information. The variable is a bit map represented as a sum, therefore, it can represent multiple failures simultaneously. The sonetVC…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.2.4.1.1.5
prtSonetVcRxSeqNumber This variable indeticates the LCAS Rx sequence number of this VC.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.4.1.1.6
prtSonetVcTxSeqNumber This variable indicates the LCAS Tx sequence number of this VC.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.4.1.1.7
prtSonetVcMfiDiffDelay This variable indicates time difference (based on MFI field) from the fastest channel (on which it will be 0), in miliSeconds units	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.4.1.1.8
prtSonetVcLoMF This variable indicates loss of Multiframe defect.	Enumeration	.1.3.6.1.4.1.164.3.1.6.2.4.1.1.9
prtSonetVcLoopStatus This variable indicates Loop Status.	Enumeration	.1.3.6.1.4.1.164.3.1.6.2.4.1.1.10
prtSonetVcLcasTxStateMachineStatus LCAS State machine status.	Enumeration	.1.3.6.1.4.1.164.3.1.6.2.4.1.1.11
prtSonetVcLcasRxStateMachineStatus LCAS State machine status.	Enumeration	.1.3.6.1.4.1.164.3.1.6.2.4.1.1.12
prtSonetVcMFLengthErrorCounter Counts the multi-frames that had wrong length (shorter or longer)	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.4.1.1.13
prtSonetVcCntrlPktCRCErrorCounter Counts Number of Control Packet CRC errors	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.4.1.1.14

Path Protection Monitoring Table

prtSonetPathProtEntry row .1.3.6.1.4.1.164.3.1.6.2.4.2.1

An entry in the Path Protection monitoring Table.
This table indicates for each protected interface
which VCs are mapped as Working VC,
which VCs are mapped as Protection VC,
and which of them are currently active.

Indexes

No indexes recorded

Column	Syntax	OID
prtSonetPathProtProtectedInterface Interface protected by path-protection, e.g. PDH (E1/T1/E3/T3) port, VCG (Virtual Concatenation Group).	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.164.3.1.6.2.4.2.1.1
prtSonetPathProtIdx Runing index of entries which are mapped to a specific interface, indicated by PrtSonetPathProtProtectedInterface. e.g - multiple working VCs and protection VCs are mapped to single Virtual Concatenation Group …	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.4.2.1.2
prtSonetPathProtWorkingVc A VC mapped to interface indicated by prtSonetPathProtProtectedInterface as working VC. The value of this object may be equal to the value of ifIndex of working VC	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.4.2.1.3
prtSonetPathProtProtectionVc A VC mapped to interface indicated by prtSonetPathProtProtectedInterface as protection VC. The value of this object may be equal to the value of ifIndex of protection VC	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.2.4.2.1.4
prtSonetPathProtActiveVc This object indicates which of the path protection VCs is currently active.	Enumeration	.1.3.6.1.4.1.164.3.1.6.2.4.2.1.5

An Augment to the APS Configuration Table
(apsConfigTable in APS-MIB).

radApsConfigEntry row .1.3.6.1.4.1.164.3.1.6.2.5.1.1

An entry in the table.

Indexes

No indexes recorded

Column	Syntax	OID
radApsConfigClearCounters Setting this object to on(3) will clear APS Counters. Upon performing this operation, the value will be automatically changed to off(2).	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.5.1.1.1
radApsConfigCommandAndStatus noOp - initial state only (cannot be Set by user). clear - clearing the last performed command. Can be Set only if previous state was other than noOp or clear. forcedSwitch - tra…	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.5.1.1.2
radApsConfigFlipOnSD Flip active channel according to SD (Signal Degradation).	Enumerationr/w	.1.3.6.1.4.1.164.3.1.6.2.5.1.1.3

An Augment to the APS Status Table
(apsStatusTable in APS-MIB).

radApsStatusEntry row .1.3.6.1.4.1.164.3.1.6.2.5.2.1

An entry in the table.

Indexes

No indexes recorded

Column	Syntax	OID
radApsStatusCurrentWorkingChannel This object indicates the port/interface index of the Current Working Channel.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.2.5.2.1.1

Sonet/SDH VCG status table.

vcGroupStatEntry row .1.3.6.1.4.1.164.3.1.6.2.6.1.1

An entry in the Sonet/SDH VCG gen staus table.

Indexes

No indexes recorded

Column	Syntax	OID
vcGroupStatRemoteChannelStatus Status of remote VCG channels as received in the local station, represented by 1 bit per channel. Refer to product spec for details.	OctetString	.1.3.6.1.4.1.164.3.1.6.2.6.1.1.1