PKTC-IETF-SIG-MIB Table View

This table describes the MTA-supported codec types.  An MTA
MUST populate this table with all possible combinations of
codecs it supports for simultaneous operation.  For example,
an MTA with two endpoints may be designed with a particular
Digital Signal Processing (DSP) and memory architecture that
allows it to support the following fixed combinations of
codecs for simultaneous operation:
          
Codec Type     Maximum Number of Simultaneous Codecs
PCMA                             3
          
PCMA                             2
PCMU                             1
          
PCMA                             1
          
PCMU                             2
          
PCMU                             3
          
PCMA                             1
G729                             1
          
G729                             2
          
PCMU                             1
G729                             1
          
Based on this example, the entries in the codec table
would be:
          
  pktcSigDev        pktcSigDev        pktcSigDev
CodecComboIndex     CodecType          CodecMax
       1               pcma                3
       2               pcma                2
       2               pcmu                1
       3               pcma                1
       3               pcmu                2
       4               pcmu                3
       5               pcma                1
       5               g729                1
       6               g729                2
       7               pcmu                1
       7               g729                1
          
An operator querying this table is able to determine all
possible codec combinations the MTA is capable of
simultaneously supporting.
          
This table MUST NOT include non-voice codecs.

pktcSigDevCodecEntry row .1.3.6.1.2.1.169.1.1.1.1

Each entry represents the maximum number of active
connections with a particular codec the MTA is capable of
supporting. Each row is indexed by a composite key
consisting of a number enumerating the particular codec
co…

Indexes

No indexes recorded

Column	Syntax	OID
pktcSigDevCodecComboIndex The index value that enumerates a particular codec combination in the pktcSigDevCodecTable.	Unsigned32	.1.3.6.1.2.1.169.1.1.1.1.1
pktcSigDevCodecType A codec type supported by this MTA.	PktcCodecType Type Values: 1 other 2 unknown 3 g729 4 reserved 5 g729E 6 pcmu 7 g726at32 8 g728 9 pcma 10 g726at16 11 g726at24 12 g726at40 13 ilbc 14 bv16	.1.3.6.1.2.1.169.1.1.1.1.2
pktcSigDevCodecMax The maximum number of simultaneous sessions of a particular codec that the MTA can support.	Unsigned32	.1.3.6.1.2.1.169.1.1.1.1.3

This table describes the signaling types supported by this
MTA.

pktcSigCapabilityEntry row .1.3.6.1.2.1.169.1.1.17.1

Entries in pktcMtaDevSigCapabilityTable - list of
supported signaling types, versions, and vendor extensions
for this MTA. Each entry in the list provides for one
signaling type and version combination. If the device
…

Indexes

No indexes recorded

Column	Syntax	OID
pktcSigCapabilityIndex The index value that uniquely identifies an entry in the pktcSigCapabilityTable.	Unsigned32	.1.3.6.1.2.1.169.1.1.17.1.1
pktcSigCapabilityType This object identifies the type of signaling used. This value has to be associated with a single signaling version.	PktcSigType Type Values: 1 other 2 ncs	.1.3.6.1.2.1.169.1.1.17.1.2
pktcSigCapabilityVersion Provides the version of the signaling type - reference pktcSigCapabilityType. Examples would be 1.0 or 2.33 etc.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.2.1.169.1.1.17.1.3
pktcSigCapabilityVendorExt The vendor extension allows vendors to provide a list of additional capabilities. The syntax for this MIB object in ABNF ([RFC5234]) is specified to be zero or more occurrences of vendor extensions, as fo…	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.2.1.169.1.1.17.1.4

The Pulse signal table defines the pulse signal operation.
There are nine types of international pulse signals,
with each signal having a set of provisionable parameters.
The values of the MIB objects in this table take effect
only if these parameters are not defined via signaling, in
which case, the latter determines the values of the
parameters.  The MIB objects in this table do not persist
across MTA reboots.

pktcSigPulseSignalEntry row .1.3.6.1.2.1.169.1.1.20.1

This object defines the set of parameters associated with
each particular value of pktcSigPulseSignalType. Each
entry in the pktcSigPulseSignalTable is indexed by the
pktcSigPulseSignalType object.
The conceptual rows …

Indexes

No indexes recorded

Column	Syntax	OID
pktcSigPulseSignalType There are nine types of international pulse signals. These signals are defined as follows: initial ring pulse loop close pulse loop open enable meter pulse meter pulse burst pulse no battery pulse normal polarity pulse…	Enumeration	.1.3.6.1.2.1.169.1.1.20.1.1
pktcSigPulseSignalFrequency This object is only applicable to the initialRing, enableMeterPulse, and meterPulseBurst signal types. This object identifies the frequency of the generated signal. The following table defines the default values for th…	Enumerationr/w	.1.3.6.1.2.1.169.1.1.20.1.2
pktcSigPulseSignalDbLevel This object is only applicable to the enableMeterPulse and meterPulseBurst signal types. This is the decibel level for each frequency at which tones could be generated at the a and b terminals (TE connection point). A…	1/10 of a dBmInteger32r/w	.1.3.6.1.2.1.169.1.1.20.1.3
pktcSigPulseSignalDuration This object specifies the pulse duration for each signal type. In addition, the MTA must accept the values in the incremental steps specific for each signal type. The following table defines the default values and the …	MillisecondsUnsigned32r/w	.1.3.6.1.2.1.169.1.1.20.1.4
pktcSigPulseSignalPulseInterval This object specifies the repeat interval, or the period, for each signal type. In addition, the MTA must accept the values in the incremental steps specific for each signal type. The following table defines the defau…	MillisecondsUnsigned32r/w	.1.3.6.1.2.1.169.1.1.20.1.5
pktcSigPulseSignalRepeatCount This object specifies how many times to repeat a pulse. This object is not used by the enableMeterPulse signal type, and in that case, the value is irrelevant. The following table defines the default values and the val…	Unsigned32r/w	.1.3.6.1.2.1.169.1.1.20.1.6

Cadence rings are defined by the telco governing
body for each country.  The MTA must be able to support
various ranges of cadence patterns and cadence periods.
The MTA will be able to support country-specific
provisioning of the cadence and idle period.  Each
cadence pattern will be assigned a unique value ranging
from 0-127 (inclusive) corresponding to the value of x,
where x is the value sent in the cadence ringing (cr)
signal cr(x), requested per the appropriate NCS
message, and defined in the E package.  The MTA will derive
the cadence periods from the ring cadence table entry, as
provisioned by the customer.  The MTA is allowed to provide
appropriate default values for each of the ring cadences.
This table only needs to be supported when the MTA
implements the E package.

pktcSigDevRingCadenceEntry row .1.3.6.1.2.1.169.1.1.31.1

Each entry in this row corresponds to a ring cadence
that is being supported by the device. The conceptual
rows MUST NOT persist across MTA reboots.

Indexes

No indexes recorded

Column	Syntax	OID
pktcSigDevRingCadenceIndex A unique value ranging from 0 to 127 that corresponds to the value sent by the LE based on country-specific cadences, one row per cadence cycle. In any given system implementation for a particular country, it is antici…	Unsigned32	.1.3.6.1.2.1.169.1.1.31.1.1
pktcSigDevRingCadence This is the Ring Cadence.	PktcRingCadencer/w Type Constraints: range: 4..36	.1.3.6.1.2.1.169.1.1.31.1.2

The Tone Table defines the composition of tones and
various tone operations.
          
The definition of the tones callWaiting1 through
callWaiting4 in this table MUST only contain the
audible tone itself; the delay between tones or the value
of the tone repeat count are not applicable for the call
waiting tones.
The delay between tones or the repeat count is controlled
by the objects pktcSigEndPntConfigCallWaitingDelay and
pktcSigEndPntConfigCallWaitingMaxRep.  If the
pktcSigDevToneType is set to either of the values
callWaiting1, callWaiting2, callWaiting3, or callWaiting4,
then the value of the pktcSigDevToneWholeToneRepeatCount
object indicates that the particular frequency group is
applicable, as a repeatable part of the tone, based on the
value of the MIB object
pktcSigDevToneWholeToneRepeatCount.
          
The MTA MUST make sure that, after the provisioning
cycle, the table is fully populated (i.e., for each
possible index, an entry MUST be defined) using
reasonable defaults for each row that was not defined
by the provisioning information delivered via MTA
Configuration.
          
The frequency composition of each tone is defined by the
pktcSigDevMultiFreqToneTable.  For each tone type defined
in pktcSigDevToneTable, the MTA MUST populate at least
one entry in the pktcSigDevMultiFreqToneTable.
          
For each particular value of pktcSigDevToneType, the
pktcSigDevToneTable table can define non-repeating and
repeating groups of the frequencies defined by the
pktcSigDevMultiFreqToneTable, such that each group is
represented by the set of the consecutive rows
(frequency group) in the pktcSigDevMultiFreqToneTable.
          
Objects in this table do not persist across MTA reboots.
For tones with multiple frequencies refer to the MIB table
pktcSigDevMultiFreqToneTable.

pktcSigDevToneEntry row .1.3.6.1.2.1.169.1.1.32.1

The different tone types that can be provisioned based on
country-specific needs.

Each entry contains the tone generation parameters for
a specific frequency group of the specific Tone Type.
The different p…

Indexes

No indexes recorded

Column	Syntax	OID
pktcSigDevToneType A unique value that will correspond to the different tone types. These tones can be provisioned based on country-specific needs. This object defines the type of tone being accessed. The alertingSignal, …	Enumeration	.1.3.6.1.2.1.169.1.1.32.1.1
pktcSigDevToneFreqGroup This MIB object represents the Tone Sequence reference of a multi-sequence tone.	Unsigned32	.1.3.6.1.2.1.169.1.1.32.1.2
pktcSigDevToneFreqCounter This MIB object represents the number of consecutive multi-frequency tones for the particular tone type in the multi-frequency table (pktcSigDevMultiFreqToneTable). Such a sequence of the consecutive mult…	Unsigned32	.1.3.6.1.2.1.169.1.1.32.1.3
pktcSigDevToneWholeToneRepeatCount This is the repeat count, which signifies how many times to repeat the entire on-off cadence sequence. Setting this object may result in a cadence duration longer or shorter than the overall signal duration specified b…	Unsigned32	.1.3.6.1.2.1.169.1.1.32.1.4
pktcSigDevToneSteady This MIB object represents the steady tone status. A value of 'true(1)' indicates that the steady tone is applied, and a value of 'false(2)' indicates otherwise. Devices must play out the on-off cadence sequence for th…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.169.1.1.32.1.5

This MIB table defines the characteristics of tones
with multiple frequencies.  The constraints imposed
on the tones by the MIB table pktcSigDevToneTable
need to be considered for MIB objects in this table
as well.
          
The MTA MUST populate the corresponding row(s)
of the pktcSigDevMultiFreqToneTable for each tone
defined in the pktcSigDevToneTable.
          
The contents of the table may be provisioned via
MTA configuration.

pktcSigDevMultiFreqToneEntry row .1.3.6.1.2.1.169.1.1.33.1

The different tone types with multiple frequencies
that can be provisioned based on country-specific
needs.

Indexes

No indexes recorded

Column	Syntax	OID
pktcSigDevToneNumber This MIB object represents the frequency reference of a multi-frequency tone.	Unsigned32	.1.3.6.1.2.1.169.1.1.33.1.1
pktcSigDevToneFirstFreqValue This MIB object represents the value of the first frequency of a tone type. A value of zero implies absence of the referenced frequency.	Unsigned32	.1.3.6.1.2.1.169.1.1.33.1.2
pktcSigDevToneSecondFreqValue This MIB object represents the value of the second frequency of a tone type. A value of zero implies absence of the referenced frequency.	Unsigned32	.1.3.6.1.2.1.169.1.1.33.1.3
pktcSigDevToneThirdFreqValue This MIB object represents the value of the third frequency of a tone type. A value of zero implies absence of the referenced frequency.	Unsigned32	.1.3.6.1.2.1.169.1.1.33.1.4
pktcSigDevToneFourthFreqValue This MIB object represents the value of the fourth frequency of a tone type. A value of zero implies absence of the referenced frequency.	Unsigned32	.1.3.6.1.2.1.169.1.1.33.1.5
pktcSigDevToneFreqMode This MIB object provides directive on the modulation or summation of the frequencies involved in the tone. It is to be noted that while summation can be done without any constraint on the number of freque…	Enumeration	.1.3.6.1.2.1.169.1.1.33.1.6
pktcSigDevToneFreqAmpModePrtg This MIB object represents the percentage of amplitude modulation applied to the second frequency when the MIB object pktcSigDevToneFreqMode is set to a value of 'firstModulatedBySecond (1)'. If the MIB o…	Unsigned32	.1.3.6.1.2.1.169.1.1.33.1.7
pktcSigDevToneDbLevel This MIB object contains the decibel level for each analog signal (tone) that is locally generated (versus in-band supervisory tones) and sourced to the a-b terminals (TE connection point). Each tone in itself may cons…	1/10 of a dBmInteger32	.1.3.6.1.2.1.169.1.1.33.1.8
pktcSigDevToneFreqOnDuration This MIB object represents the duration for which the frequency reference corresponding to the tone type is turned on.	millisecondsUnsigned32	.1.3.6.1.2.1.169.1.1.33.1.9
pktcSigDevToneFreqOffDuration This MIB object represents the duration for which the frequency reference corresponding to the tone type is turned off.	millisecondsUnsigned32	.1.3.6.1.2.1.169.1.1.33.1.10
pktcSigDevToneFreqRepeatCount This MIB object indicates the number of times to repeat the cadence cycle represented by the on/off durations (refer to the MIB objects pktcSigDevToneFreqOnDuration and pktcSigDevToneFreqOffDuration). Set…	Unsigned32	.1.3.6.1.2.1.169.1.1.33.1.11

This table describes the information pertaining to each
endpoint of the MTA.  All entries in this table represent
the provisioned endpoints provisioned with the information
required by the MTA to maintain the NCS protocol
communication with the CMS.  Each endpoint can be assigned
to its own CMS.  If the specific endpoint does not have
the corresponding CMS information in this table, the
endpoint is considered as not provisioned with voice
services.  Objects in this table do not persist across
MTA reboots.

pktcSigEndPntConfigEntry row .1.3.6.1.2.1.169.1.2.1.1

Each entry in the pktcSigEndPntConfigTable represents
required signaling parameters for the specific endpoint
provisioned with voice services. The conceptual rows MUST
NOT persist across MTA reboots.

Indexes

No indexes recorded

Column	Syntax	OID
pktcSigEndPntConfigCallAgentId This object contains a string indicating the call agent name (e.g., ca@example.com). The call agent name, after the character '@', MUST be a fully qualified domain name (FQDN) and MUST have a corresponding pktcMtaDevCm…	OctetStringr/w	.1.3.6.1.2.1.169.1.2.1.1.1
pktcSigEndPntConfigCallAgentUdpPort This object contains the current value of the User Datagram Protocol (UDP) receive port on which the call agent will receive NCS from the endpoint. For each particular endpoint, the MTA MUST use the current value of thi…	Unsigned32r/w	.1.3.6.1.2.1.169.1.2.1.1.2
pktcSigEndPntConfigPartialDialTO This object contains the value of the partial dial time out. The time out (TO) elements are intended to limit the time a tone or frequency is generated. When this MIB object is set to a value of '0', the MTA MUST NOT g…	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.3
pktcSigEndPntConfigCriticalDialTO This object contains the value of the critical dial time out. The time out (TO) elements are intended to limit the time a tone or frequency is generated. When this MIB object is set to a value of '0', the MTA MUST NOT …	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.4
pktcSigEndPntConfigBusyToneTO This object contains the default time out value for busy tone. The MTA MUST NOT update this object with the value provided in the NCS message (if present). If the value of the object is modified by the SNMP Management…	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.5
pktcSigEndPntConfigDialToneTO This object contains the default time out value for dial tone. The MTA MUST NOT update this object with the value provided in the NCS message (if present). If the value of the object is modified by the SNMP Management…	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.6
pktcSigEndPntConfigMessageWaitingTO This object contains the default time out value for message waiting indicator. The MTA MUST NOT update this object with the value provided in the NCS message (if present). If the value of the object is modified by the…	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.7
pktcSigEndPntConfigOffHookWarnToneTO This object contains the default time out value for the off-hook warning tone. The MTA MUST NOT update this object with the value provided in the NCS message (if present). If the value of the object is modified by the…	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.8
pktcSigEndPntConfigRingingTO This object contains the default time out value for ringing. The MTA MUST NOT update this object with the value provided in the NCS message (if present). If the value of the object is modified by the SNMP Management S…	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.9
pktcSigEndPntConfigRingBackTO This object contains the default time out value for ring back. The MTA MUST NOT update this object with the value provided in the NCS message (if present). If the value of the object is modified by the SNMP Management…	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.10
pktcSigEndPntConfigReorderToneTO This object contains the default time out value for reorder tone. The MTA MUST NOT update this object with the value provided in the NCS message (if present). If the value of the object is modified by the SNMP Managem…	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.11
pktcSigEndPntConfigStutterDialToneTO This object contains the default time out value for stutter dial tone. The MTA MUST NOT update this object with the value provided in the NCS message (if present). If the value of the object is modified by the SNMP Ma…	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.12
pktcSigEndPntConfigTSMax This MIB object is used as part of an NCS retransmission algorithm. Prior to any retransmission, the MTA must check to make sure that the time elapsed since the sending of the initial datagram does not exceed the value…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.13
pktcSigEndPntConfigMax1 This object contains the suspicious error threshold for signaling messages. The pktcSigEndPntConfigMax1 object indicates the retransmission threshold at which the MTA MAY actively query the domain name server (DNS) in …	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.14
pktcSigEndPntConfigMax2 This object contains the disconnect error threshold for signaling messages. The pktcSigEndPntConfigMax2 object indicates the retransmission threshold at which the MTA SHOULD contact the DNS one more time to see if any …	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.15
pktcSigEndPntConfigMax1QEnable This object enables/disables the Max1 domain name server (DNS) query operation when the pktcSigEndPntConfigMax1 threshold has been reached. A value of true(1) indicates enabling, and a value of false(2) indicates disabl…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.169.1.2.1.1.16
pktcSigEndPntConfigMax2QEnable This object enables/disables the Max2 domain name server (DNS) query operation when the pktcSigEndPntConfigMax2 threshold has been reached. A value of true(1) indicates enabling, and a value of false(2) indicates disabl…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.169.1.2.1.1.17
pktcSigEndPntConfigMWD Maximum Waiting Delay (MWD) contains the maximum number of seconds an MTA waits, after powering on, before initiating the restart procedure with the call agent.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.18
pktcSigEndPntConfigTdinit This MIB object represents the 'disconnected' initial waiting delay within the context of an MTA's 'disconnected procedure'. The 'disconnected procedure' is initiated when an endpoint becomes 'disconnected' while attem…	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.19
pktcSigEndPntConfigTdmin This MIB object represents the 'disconnected' minimum waiting delay within the context of an MTA's 'disconnected procedure', specifically when local user activity is detected. The 'disconnected procedure' is initiated w…	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.20
pktcSigEndPntConfigTdmax This object contains the maximum number of seconds the MTA waits, after a disconnect, before initiating the disconnected procedure with the call agent.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.21
pktcSigEndPntConfigRtoMax This object specifies the maximum number of seconds the MTA waits for a response to an NCS message before initiating a retransmission.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.22
pktcSigEndPntConfigRtoInit This object contains the initial number of seconds for the retransmission timer.	millisecondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.23
pktcSigEndPntConfigLongDurationKeepAlive Specifies a time out value, in minutes, for sending long duration call notification messages.	minutesSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.24
pktcSigEndPntConfigThist Time out period, in seconds, before no response is declared.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.169.1.2.1.1.25
pktcSigEndPntConfigStatus This object contains the Row Status associated with the pktcSigEndPntConfigTable. There are no restrictions or dependencies amidst the columnar objects before this row can be activated or for modifications of the colum…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.169.1.2.1.1.26
pktcSigEndPntConfigCallWaitingMaxRep This object contains the default value of the maximum number of repetitions of the Call Waiting tone that the MTA will play from a single CMS request. The MTA MUST NOT update this object with the information provided i…	Unsigned32r/w	.1.3.6.1.2.1.169.1.2.1.1.27
pktcSigEndPntConfigCallWaitingDelay This object contains the delay between repetitions of the Call Waiting tone that the MTA will play from a single CMS request.	secondsUnsigned32r/w	.1.3.6.1.2.1.169.1.2.1.1.28
pktcSigEndPntStatusCallIpAddressType This object contains the type of Internet address contained in the MIB object 'pktcSigEndPntStatusCallIpAddress'. Since pktcSigEndPntStatusCallIpAddress is expected to contain an IP address, a value of dn…	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.2.1.169.1.2.1.1.29
pktcSigEndPntStatusCallIpAddress This MIB object contains the chosen IP address of the CMS currently being used for the corresponding endpoint. The device determines the IP address by using DNS to resolve the IP address of the CMS from t…	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.2.1.169.1.2.1.1.30
pktcSigEndPntStatusError This object contains the error status for this interface. The operational status indicates that all operations necessary to put the line in service have occurred, and the CMS has acknowledged the Restart In Progress (RS…	Enumeration	.1.3.6.1.2.1.169.1.2.1.1.31
pktcSigEndPntConfigMinHookFlash This is the minimum time a line needs to be on-hook for a valid hook flash. The value of this object MUST be greater than the value of pktcSigEndPntConfigPulseDialMaxBreakTime. The value of pktcSigEndPntConfigMinHookF…	MillisecondsUnsigned32	.1.3.6.1.2.1.169.1.2.1.1.32
pktcSigEndPntConfigMaxHookFlash This is the maximum time a line needs to be on-hook for a valid hook flash. The value of pktcSigEndPntConfigMaxHookFlash MUST be greater than pktcSigEndPntConfigMinHookFlash. This object MUST only be set via the MTA c…	MillisecondsUnsigned32	.1.3.6.1.2.1.169.1.2.1.1.33
pktcSigEndPntConfigPulseDialInterdigitTime This is the pulse dial inter-digit time out. This object MUST only be set via the MTA configuration during the provisioning process.	MillisecondsUnsigned32	.1.3.6.1.2.1.169.1.2.1.1.34
pktcSigEndPntConfigPulseDialMinMakeTime This is the minimum make pulse width for the dial pulse. The value of pktcSigEndPntConfigPulseDialMinMakeTime MUST be less than pktcSigEndPntConfigPulseDialMaxMakeTime. This object MUST only be set via the MTA configur…	MillisecondsUnsigned32	.1.3.6.1.2.1.169.1.2.1.1.35
pktcSigEndPntConfigPulseDialMaxMakeTime This is the maximum make pulse width for the dial pulse. The value of pktcSigEndPntConfigPulseDialMaxMakeTime MUST be greater than pktcSigEndPntConfigPulseDialMinMakeTime. This object MUST only be provided via the confi…	MillisecondsUnsigned32	.1.3.6.1.2.1.169.1.2.1.1.36
pktcSigEndPntConfigPulseDialMinBreakTime This is the minimum break pulse width for the dial pulse. The value of pktcSigEndPntConfigPulseDialMinBreakTime MUST be less than pktcSigEndPntConfigPulseDialMaxBreakTime. This object must only be provided via the confi…	MillisecondsUnsigned32	.1.3.6.1.2.1.169.1.2.1.1.37
pktcSigEndPntConfigPulseDialMaxBreakTime This is the maximum break pulse width for the dial pulse. The value of pktcSigEndPntConfigPulseDialMaxBreakTime MUST be greater than pktcSigEndPntConfigPulseDialMinBreakTime. This object MUST only be provided via the co…	MillisecondsUnsigned32	.1.3.6.1.2.1.169.1.2.1.1.38