LUM-EQUIPMENT-MIB Table View

An arbitrary index assigned to each
subrack entry.

The name of the subrack, for example 'sub1'
where the number indicates the subrack number.

The number of the subrack.

User configurable label.

The row in the invPhysTable for this subrack.
Set to 0 if not known.

All fan units in a subrack have failed.

A(ctivation): fanUnitFailed active for all fans
within a subrack.

D(e-activiation): fanUnitFailed cleared for one
fan unit.

SNMP administrivia.
Manages creation and deletion of conceptual rows.
See also SNMPv2-TC.

The expected subrack type.

The actual subrack type. If an unexpected
subrack has been detected this variable can be
used to see what type of subrack has been
detected.

A type of subrack not matching the expected
type is present.

A: A subrack with type different from the
expected type is present (even if the subrack
is not activated).

D: The type matches t…

The temperature in the subrack in 0.1 degrees centigrade.

The threshold for environmental temperature
in the subrack is exceeded.

A: The temperature exceeds the associated threshold.

D: Temperature is 0.5 degrees centigrade below the
associated th…

The threshold for temperature alarm in the
subrack in 0.1 degrees centigrade.

The subrack data (dipswitches for subrackId and/or
system mode) has been changed. Changing this data might
affect the system behaviour after the next restart.

A: The subrack data has been changed since st…

The value read from the system mode
dipswitches at startup of the CU was
diffrent from 0.

This will affect the behaviour of the
system.

If the lowest bit is set, the backup
is read from the…

The value of the system mode dipswitches
read at startup. This value determines the
system behaviour.

The current value of the system mode
dipswitches. Will be used at the next
restart.

The administrative state of the subrack.

down - This subrack should not be monitored.
Suppresses alarms.

up - The subrack should be monitored.

The operational state of the subrack.

notPresent - The subrack is not available.

down - The subrack remains in the 'down'-state
when adminStatus is set to 'down'.

up - The su…

Property mask.

Length of the half-height slot divider shelf. To be
manually entered by the user. A value of 0 is
interpreted as 'not yet defined by user'.

The subrack LAN/DCN module is missing.

A(ctivation): LAN/DCN module disconnected from subrack
for more than 2 seconds.

D(e-activiation): LAN/DCN module connected to subrack
…

The lowest slot number where it is possible to
configure a passive board. Automatically configured
to the actual value supported by hardware if the
hardware is present on subrack configuration.

If no hard…

The actual lowest slot number where it is possible
to configure a passive board.

When no subrack hardware is present, this value is
'undefined'.

The expected first passive slot allows more passive
boards than the hardware supports.

A(ctivation): A subrack and control unit combination
which supports fewer passive boards
…

The access identifier (AID) of the product.
The format is according to GR-833.

The Physical location of the product.
The format is according to GR-833.

Command to change expected type,
used when upgrading subrack to a new version,
e.g TM3000 to TM3000/II

An arbitrary index assigned to each
board entry.

The name of the board, for example 'tpmr2500:1:2'
where the first number indicates in which sub-rack
the board is present and the second number
in which slot.

The expected board type.

The actual board type. If an unexpected board
has been detected this variable can be used to
see what type of board has been detected.

User configurable label.

The number of the subrack where the board is
located.

The slot where the board is located.

The temperature on the board in 0.1 degrees
centigrade.

The row in the invPhysTable for this board.
Set to 0 if not known.

LED test for the board.

off - Normal operation.

on - Light all leds.

The administrative state of the board.

down - The board should be inactive.
Alarms are suppressed.

service - The board is activated but alarms are
suppressed. Intended for use during servic…

The operational state of the board.

notPresent - The board is not available.

down - The board remains in the 'down'-state
when adminStatus is set to 'down' or if there is
a fault preventing…

The time when the operational state of the
board entry was last changed.

SNMP administrivia.
Manages creation and deletion of conceptual rows.
See also SNMPv2-TC.

There is no board present in a slot where the
expected board type is defined. Suppressed if
administrative status is down.

A(ctivation): Card out of place (COP) indication
active for more than 2 seconds.
…

A type of board not matching the expected type
is present and active in the same slot.
Since the default value for the type is
'undefined' this alarm is raised when inserting
an unconfigured board.

A: A b…

The threshold for environmental temperature
on the board is exceeded.

A: The temperature exceeds the associated
threshold.

D: Temperature is 0.5 degrees centigrade
below the associated thre…

Communication between the control unit and the
the board has failed completely.

A: There is a board present but there has been
no communication established within 20 seconds.

D: Communicati…

Communication between the control unit and the
board has failed due to incompatible software.

A: The control unit and the board have
in-compatible software.

D: The control unit and the boar…

Secondary DC power (1.8 or 2.5 V) failure.

A: The secondary DC power on the board has
failed.

D: The secondary DC power is present.

Note: If primary power fails a
'communicat…

Product data vital for the safe operation
of the equipment is missing.

A: Product data missing.

D: Product data present.

Administrative product data is missing.

A: Product data missing.

D: Product data present.

The board is undergoing maintenance, adminStatus
is set to service.

A: AdminStatus is set to service.

D: AdminStatus is set to another value.

The threshold for temperature alarm on the
board in 0.1 degrees centigrade.

The version of the board SW does not match
the SW version running och the main CU.

For versions to match, the release number,
e.g. 'r2b', must be the same. The build
number is not required to be the same.…

Property mask.

The low threshold for environmental temperature
on the board is exceeded.

A: The temperature exceeds the associated
low threshold.

D: Temperature is 0.5 degrees centigrade
above the associa…

The very high threshold for environmental
temperature on the board is exceeded.

A: The temperature exceeds the associated
threshold.

D: Temperature is 0.5 degrees centigrade
below the assoc…

Applicable for cu, cu2osc, cuSfp, cuSfpii and voa8chii.

Reconfigure cu or cu2osc board to cuSfp.
Reconfigure cu2osc or cuSfp board to cuSfpii.
Reconfigure older CU-board to cuSfpiii.
Reconfigure voa8chii …

LED status for the board.
This is primarily intended for debugging

Information (for example firmware and serial number) about the module.

A new SW version on the board has been activated,
but the board has not been rebooted. This means that
after the next reboot, a new SW will be active.

For the main CU, this also means that the backup
will…

The environmental temperature on the board
is below startuptemperature (+3 centigrade).

A: The temperature is below +3 degrees centigrade.

D: Temperature has increased to +5 degrees centigr…

The threshold for low temperature alarm on the
board in 0.1 degrees centigrade.

Additional information about the board,
e.g. FPGA revision.

The card fails to boot.

A: The card fails to boot.

D: The card boot successfully.

A hardware error occured.

A: A hardware error occured.

D: No hardware error.

Low disk space in the board.

A: Not enough disk space.

D: Disk space is enough.

Clock frequency is out of range.

A: Clock frequency out is out of range.

D: Clock frequency is in range.

Postpone activation of new traffic firmware when
the board software is upgraded next time. If no
firmware changes are available when upgrading this
option will not have any effect.

Command to activate a pending firmware upgrade.

Firmware activation has been postponed in a
previous software upgrade.

A configuration request has failed since the chosen
feature is not supported by the active firmware.

The traffic HW has been programmed by a version
of the system that does not offer a supported
upgrade path to the currently running version.
This typically happens after a downgrade
or rollback of the SW. The state of t…

The running version of the SW cannot recover
the settings of the traffic HW/FW. The state
of the traffic HW is unknown. A reset of the
traffic unit is recommended.
This will cause a short traffic hit.

Determines board configuration.

dualMuxponderProt - 2x Muxponder with protection
hexTransponder - 6x Transponder
tripleMuxponderProt - 3x Muxponder with protection
quadTransponderProt - 4x Transpon…

Monitor Cabinet status if enabled. Alarm is raised if connection is lost.

Connection to the cabinet has failed.

Operational Variant mode of board, Normal or OpenFlow Controlled.

The access identifier (AID) of the product.
The format is according to GR-833.

The Physical location of the product.
The format is according to GR-833.

An arbitrary index assigned to each power module.

The name of the power module.
For example 'pow:1:2'.

The number of the subrack in which the power
module is present.

The number of the slot in which the power
module is present.

The the type of power module.

ac - AC power supply (230V).

dc - DC power supply (48V).

The row in the invPhysTable for this power
module. Set to 0 if not known.

The administrative state of the power module.

down - This power module is not monitored.
Suppresses alarms.

up - The power module is monitored.

The operational state of the power module.

notPresent - The power module is not present.

down - The module is not active or there are
faults preventing it from going to the
'up'-state.
…

Manages creation and deletion of conceptual rows.
See also SNMPv2-TC.

AC power supply failed (230 V).

A(ctivation): Active HW indication.

D(e-activation): Inactive HW indication.

DC power supply failed (48 V).

A: Active HW indication.

D: Inactive HW indication.

The built-in temperature monitoring of the power
module thinks it is too hot.

A: Active HW indication.

D: Inactive HW indication.

The power module is not available.

A: Active HW indication.

D: Inactive HW indication.

Property mask.

The severity of DC Power failed alarm.

The access identifier (AID) of the product.
The format is according to GR-833.

The Physical location of the product.
The format is according to GR-833.

An arbitrary index assigned to each fan module.

The name of the fan module.
For example 'fan:1:2', where the first number
indicates the subrack and the second number the
fan slot.

The number of the subrack in which the fan
module is present.

The number of the fan-slot in which the fan
module is present.

The row in the invPhysTable for this fan module.
Set to 0 if not known.

The administrative state of the fan module.

down - This fan module should not be monitored.
Suppresses alarms. Useful if a subrack has only
one fan for some reason.

up - The fan module shou…

The operational state of the fan module.

Note: It is not possible to distinguish between
a missing fan and a failed fan. Therefore
'notPresent' is currently not used.

down - The fan module …

Manages creation and deletion of conceptual rows.
See also SNMPv2-TC.

The fan module has failed or is absent.

A(ctivation): Active HW indication.

D(e-activation): Inactive HW indication.

The main fan module has failed or is absent.

A(ctivation): Active HW indication.

D(e-activation): Inactive HW indication.

Property mask.

The Fan malfunction or fan speed differs from the set speed.

A(ctivation): Active HW indication.

D(e-activation): Inactive HW indication.

The access identifier (AID) of the product.
The format is according to GR-833.

The Physical location of the product.
The format is according to GR-833.

An arbitrary index assigned to each
slot entry.

The name of the slot, for example 'tpmr2500:1:2'
where the first number indicates in which sub-rack
the slot is present and the second number
in which slot.

The number of the subrack in which the slot
is present.

The slot number.

The administrative state of the slot.

down - The slot is not monitored.

up - The interface should be activated.

Tells if the slot is used or not.

used - Slot is used.

notUsed - Slot is not used.

Slot is empty, alarm only applicable for systems with mendatory slot usage

A: Slot is empty.

D: No empty slot.

Is the entity equipped.

The access identifier (AID) of the slot.
The format is according to GR-833.

The physical location of the slot.
The format is according to GR-833.

An arbitrary index assigned to each entry.

The actual board type hosting the optical module.

The type of optical module,
for example monitor, switch, wss, amp etc

The management name of the interface,
for example 'module:[HostBoardType]:[ moduleType]:[subrack]:[slot]'.

The number of the subrack where the module
is located.

The number of the slot where the module is
located.

Firmware version of the module.

Serial number of the module.

Module is warming up, the optics has not reached a stable
state.

True: Module is warming up.

False: Module is ready and optics have reached stable state.

The module is experiencing a failure.

A(ctivation): The module has failed

D(e-activation): The module is OK again