equipmentBoardTempLowThreshold
LUM-EQUIPMENT-MIB ·
.1.3.6.1.4.1.8708.2.11.2.3.1.1.34
Object
column
Integer32
The threshold for low temperature alarm on the board in 0.1 degrees centigrade.
Context
- MIB
- LUM-EQUIPMENT-MIB
- OID
.1.3.6.1.4.1.8708.2.11.2.3.1.1.34- Type
- column
- Access
- readonly
- Status
- current
- Parent
- equipmentBoardEntry
- Table
- equipmentBoardTable
- Siblings
- 50
Syntax
Integer32
Values & Constraints
Object Constraints
range: -400-400
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| equipmentBoardIndex An arbitrary index assigned to each
board entry. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.11.2.3.1.1.1 |
| equipmentBoardLedTest LED test for the board.
off - Normal operation.
on - Light all leds. | column | Enumeration | .1.3.6.1.4.1.8708.2.11.2.3.1.1.10 |
| equipmentBoardAdminStatus The administrative state of the board.
down - The board should be inactive.
Alarms are suppressed.
service - The board is activated but alarms are
su… | column | LUM-TCBoardOrInterfaceAdminStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.11 |
| equipmentBoardOperStatus The operational state of the board.
notPresent - The board is not available.
down - The board remains in the 'down'-state
when adminStatus is set to … | column | LUM-TCBoardOrInterfaceOperStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.12 |
| equipmentBoardLastChangeTime The time when the operational state of the
board entry was last changed. | column | SNMPv2-TCDateAndTime | .1.3.6.1.4.1.8708.2.11.2.3.1.1.13 |
| equipmentBoardRowStatus SNMP administrivia.
Manages creation and deletion of conceptual rows.
See also SNMPv2-TC. | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.14 |
| equipmentBoardMissing There is no board present in a slot where the
expected board type is defined. Suppressed if
administrative status is down.
A(ctivation): Card out of place (COP) ind… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.15 |
| equipmentBoardUnexpectedType A type of board not matching the expected type
is present and active in the same slot.
Since the default value for the type is
'undefined' this alarm is raised when inserting
an u… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.16 |
| equipmentBoardTempHighExceeded The threshold for environmental temperature
on the board is exceeded.
A: The temperature exceeds the associated
threshold.
D: Temperature is 0.5 degr… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.17 |
| equipmentBoardCommunicationFailure Communication between the control unit and the
the board has failed completely.
A: There is a board present but there has been
no communication established within 2… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.18 |
| equipmentBoardInterworkFailed Communication between the control unit and the
board has failed due to incompatible software.
A: The control unit and the board have
in-compatible software.
… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.19 |
| equipmentBoardName The name of the board, for example 'tpmr2500:1:2'
where the first number indicates in which sub-rack
the board is present and the second number
in which slot. | column | LUM-TCMgmtNameString | .1.3.6.1.4.1.8708.2.11.2.3.1.1.2 |
| equipmentBoardSecondaryPowerFailed Secondary DC power (1.8 or 2.5 V) failure.
A: The secondary DC power on the board has
failed.
D: The secondary DC power is present.
No… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.20 |
| equipmentBoardVitalDataMissing Product data vital for the safe operation
of the equipment is missing.
A: Product data missing.
D: Product data present. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.21 |
| equipmentBoardNonVitalDataMissing Administrative product data is missing.
A: Product data missing.
D: Product data present. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.22 |
| equipmentBoardUnderMaintenance The board is undergoing maintenance, adminStatus
is set to service.
A: AdminStatus is set to service.
D: AdminStatus is set to another value. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.23 |
| equipmentBoardTempThreshold The threshold for temperature alarm on the
board in 0.1 degrees centigrade. | column | Integer32 | .1.3.6.1.4.1.8708.2.11.2.3.1.1.24 |
| equipmentBoardSwVersionMismatch The version of the board SW does not match
the SW version running och the main CU.
For versions to match, the release number,
e.g. 'r2b', must be the same. The buil… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.25 |
| equipmentBoardObjectProperty Property mask. | column | LUM-TCObjectProperty | .1.3.6.1.4.1.8708.2.11.2.3.1.1.26 |
| equipmentBoardTempLow The low threshold for environmental temperature
on the board is exceeded.
A: The temperature exceeds the associated
low threshold.
D: Temperature is … | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.27 |
| equipmentBoardTempVeryHigh The very high threshold for environmental
temperature on the board is exceeded.
A: The temperature exceeds the associated
threshold.
D: Temperature i… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.28 |
| equipmentBoardReconfigure Applicable for cu, cu2osc, cuSfp, cuSfpii and voa8chii.
Reconfigure cu or cu2osc board to cuSfp.
Reconfigure cu2osc or cuSfp board to cuSfpii.
Reconfigure older CU-… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.11.2.3.1.1.29 |
| equipmentBoardExpectedType The expected board type. | column | EquipmentBoardType | .1.3.6.1.4.1.8708.2.11.2.3.1.1.3 |
| equipmentBoardLedStatus LED status for the board.
This is primarily intended for debugging | column | Enumeration | .1.3.6.1.4.1.8708.2.11.2.3.1.1.30 |
| equipmentBoardModuleInfo Information (for example firmware and serial number) about the module. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.11.2.3.1.1.31 |
| equipmentBoardNewSwActivatedButNotRestarted A new SW version on the board has been activated,
but the board has not been rebooted. This means that
after the next reboot, a new SW will be active.
For the main … | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.32 |
| equipmentBoardLowTemperature The environmental temperature on the board
is below startuptemperature (+3 centigrade).
A: The temperature is below +3 degrees centigrade.
D: Tempera… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.33 |
| equipmentBoardAdditionalInfo Additional information about the board,
e.g. FPGA revision. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.11.2.3.1.1.35 |
| equipmentBoardBootError The card fails to boot.
A: The card fails to boot.
D: The card boot successfully. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.36 |
| equipmentBoardHardwareError A hardware error occured.
A: A hardware error occured.
D: No hardware error. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.37 |
| equipmentBoardLowDiskSpace Low disk space in the board.
A: Not enough disk space.
D: Disk space is enough. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.38 |
| equipmentBoardClockDrift Clock frequency is out of range.
A: Clock frequency out is out of range.
D: Clock frequency is in range. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.39 |
| equipmentBoardActualType The actual board type. If an unexpected board
has been detected this variable can be used to
see what type of board has been detected. | column | EquipmentBoardType | .1.3.6.1.4.1.8708.2.11.2.3.1.1.4 |
| equipmentBoardPostponeFwUpgrade Postpone activation of new traffic firmware when
the board software is upgraded next time. If no
firmware changes are available when upgrading this
option will not have any effect. | column | Enumeration | .1.3.6.1.4.1.8708.2.11.2.3.1.1.40 |
| equipmentBoardActivatePendingFwCommand Command to activate a pending firmware upgrade. | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.11.2.3.1.1.41 |
| equipmentBoardFwActivationPending Firmware activation has been postponed in a
previous software upgrade. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.42 |
| equipmentBoardFeatureNotSupported A configuration request has failed since the chosen
feature is not supported by the active firmware. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.43 |
| equipmentBoardFwReloadNeeded The traffic HW has been programmed by a version
of the system that does not offer a supported
upgrade path to the currently running version.
This typically happens after a downgra… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.44 |
| equipmentBoardFwContextUnknown The running version of the SW cannot recover
the settings of the traffic HW/FW. The state
of the traffic HW is unknown. A reset of the
traffic unit is recommended.
This will cause… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.45 |
| equipmentBoardBoardVariant Determines board configuration.
dualMuxponderProt - 2x Muxponder with protection
hexTransponder - 6x Transponder
tripleMuxponderProt - 3x Muxponder with prot… | column | Enumeration | .1.3.6.1.4.1.8708.2.11.2.3.1.1.46 |
| equipmentBoardCabinetConnectivity Monitor Cabinet status if enabled. Alarm is raised if connection is lost. | column | Enumeration | .1.3.6.1.4.1.8708.2.11.2.3.1.1.47 |
| equipmentBoardCabinetConnectionFailure Connection to the cabinet has failed. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.11.2.3.1.1.48 |
| equipmentBoardOperationalVariant Operational Variant mode of board, Normal or OpenFlow Controlled. | column | Enumeration | .1.3.6.1.4.1.8708.2.11.2.3.1.1.49 |
| equipmentBoardDescr User configurable label. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.11.2.3.1.1.5 |
| equipmentBoardAid The access identifier (AID) of the product.
The format is according to GR-833. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.11.2.3.1.1.50 |
| equipmentBoardPhysicalLocation The Physical location of the product.
The format is according to GR-833. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.11.2.3.1.1.51 |
| equipmentBoardSubrack The number of the subrack where the board is
located. | column | LUM-TCSubrackNumber | .1.3.6.1.4.1.8708.2.11.2.3.1.1.6 |
| equipmentBoardSlot The slot where the board is located. | column | LUM-TCSlotNumber | .1.3.6.1.4.1.8708.2.11.2.3.1.1.7 |
| equipmentBoardTemp The temperature on the board in 0.1 degrees
centigrade. | column | Integer32 | .1.3.6.1.4.1.8708.2.11.2.3.1.1.8 |
| equipmentBoardInvPhysIndexOrZero The row in the invPhysTable for this board.
Set to 0 if not known. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.11.2.3.1.1.9 |