DC-VPWS-MIB Table View

VPWS Configuration Table.
          
This table specifies information for configuring and
monitoring Virtual Private Wire Services (VPWS).
          
Note that any changes made to this table when
vpwsStatusOperStatus is 'up' may cause the VPWS to be
deactivated (vpwsStatusOperStatus 'down') before the change
is made.  The VPWS will then attempt to re-activate.  The
VPWS may or may not re-activate depending on the validity of
the new configuration.

VPWS Status Table (read-only).
          
This table reports the status of Virtual Private Wire
Services (VPWS).

VPWS Binding Config Table.
          
This table configures bindings of Attachment Circuits (ACs)
to VPWS instances, pseudowires (PWs), and layer 2 local
switching rules (hairpins).
          
Multiple ACs can be associated with a single VPWS.
          
If the binding corresponds to two VPWS sites that are hosted
by a single PE router, a hairpin can be created between the
two sites' ACs.  Otherwise, a PW set is used to establish
connectivity.
          
The method for associating ACs with PWs depends on whether
auto-discovery is enabled.
          
-  If auto-discovery is disabled (vpwsConfigADType = none)
   then PWs are provisioned in the pwTable.  In this case,
   each AC is bound to a set of provisioned PWs, that are
   identified by a PW Set Index.  PW redundancy
   configuration is not yet supported by L2VM provisioned
   PWs, therefore the PW Set will have a single member, and
   this set index can be set to the pwIndex in the pwTable
   of that PW.  This form of binding is known as a
   double-sided binding since the PW(s) must be provisioned
   in the pwTable at each end of the virtual circuit.
          
-  If auto-discovery is enabled (vpwsConfigADType = bgp)
   then the VPWS service establishes a PW between each pair
   of VPWS sites within the VPWS, using BGP auto-discovery
   to determine which PE router hosts each VPWS site.  In
   this case, each AC is bound to a PW that is identified by
   the local and remote site IDs.  The PE router creates
   these PWs automatically as a result of the BGP
   auto-discovery process.  This form of configuration is
   sometimes known as 'colored pools'.  In this approach the
   operator configures a pool of ACs for each local site,
   and each pool is identified by a site ID or 'color'.  The
   VPWS service establishes a PW between each pair of
   'colored pools' (VPWS sites), and each AC is bound to a
   PW associated with the same 'colored pool' (local site
   ID).
          
-  If auto-discovery is enabled (vpwsConfigADType = bgp)
   then an AC can still be bound to a PW that is provisioned
   in the pwTable MIB, for example to incorporate a legacy
   PE router that does not support auto-discovery into the
   VPWS.
          
The method for associating ACs with other ACs in a hairpin
also depends on whether auto-discovery is enabled.
          
-  If auto-discovery is disabled, the AC is bound to another
   AC directly, by configuring its interface index in this
   table.  In this case the PW set index can also optionally
   be specified to provide redundant connectivity to the
   other site.
          
-  If auto-discovery is enabled, the BGP auto-discovery
   process ascertains that this PE router also hosts the
   remote site, and automatically binds the two ACs.
          
In either case a row in this table only establishes
unidirectional connectivity for a hairpin.  For full
connectivity, the opposite direction will need to be
configured in the same manner (though this need not be in
the same VPWS instance).
          
Each VPWS Binding is configured with a PW binding type,
given by vpwsBindCfgPwBindType, which specifies whether the
PW Set to which the AC is bound is identified by a PW Set
index and/or hairpin interface index (and so is provisioned)
or by a local and remote site ID (and so is auto-created as
a result of BGP auto-discovery).
          
This table is indexed on AC interface index to ensure that
each AC is only ever bound to a single VPWS.  The read-only
vpwsBindTable can be used to show the ACs bound to each
VPWS.
          
Note that changes to this table may cause the corresponding
AC to go operationally down as it may involve re-programming
the AC in the data plane.

VPWS Binding Table (read-only).
          
This table displays the Attachment Circuit (AC) bindings
in a VPWS.
          
Bindings are configured in the vpwsBindCfgTable.
          
This table is read-only.