CISCO-OPTICAL-MONITOR-MIB Table View
Table-centric layout grouping table, row, and column objects.
Tables
4
Rows
4
Columns
37
cOpticalMonTable
table.1.3.6.1.4.1.9.9.264.1.1.1
·
1 row entry
·
19 columns
This table provides objects to monitor optical parameters in a network element. It also provides objects for setting high and low threshold levels, with configurable severities, on these monitored parameters.
An entry in the cOpticalMonTable provides objects to
monitor an optical parameter and set threshold levels
on that parameter, at an optical interface.
Note that the set of monitored optical parameters may v…
monitor an optical parameter and set threshold levels
on that parameter, at an optical interface.
Note that the set of monitored optical parameters may v…
Indexes
| Column | Syntax | OID | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
cOpticalMonDirection
This object indicates the direction monitored for the
optical interface, in this entry. |
OpticalIfDirection Textual Convention: OpticalIfDirection EnumerationType Values:
|
.1.3.6.1.4.1.9.9.264.1.1.1.1.1 |
||||||||||||||
|
cOpticalMonLocation
This object indicates whether the optical characteristics are
measured before or after adjustment (e.g. optical amplification or attenuation), at this interface. |
OpticalIfMonLocation Textual Convention: OpticalIfMonLocation EnumerationType Values:
|
.1.3.6.1.4.1.9.9.264.1.1.1.1.2 |
||||||||||||||
|
cOpticalMonParameterType
This object specifies the optical parameter that is being
monitored in this entry. |
OpticalParameterType Textual Convention: OpticalParameterType EnumerationType Values:
|
.1.3.6.1.4.1.9.9.264.1.1.1.1.3 |
||||||||||||||
|
cOpticalParameterValue
This object gives the value measured for the particular
optical parameter specified by the cOpticalMonParameterType object. |
OpticalParameterValue Textual Convention: OpticalParameterValue Integer32Type Constraints: range: -1000000..1000000 |
.1.3.6.1.4.1.9.9.264.1.1.1.1.4 |
||||||||||||||
|
cOpticalParamHighAlarmThresh
This object is used to set a high alarm threshold on the
optical parameter being monitored. An alarm condition will be raised if the value given by cOpticalParameterValue goes from below the value configu… |
OpticalParameterValuer/w Textual Convention: OpticalParameterValue Integer32Type Constraints: range: -1000000..1000000 |
.1.3.6.1.4.1.9.9.264.1.1.1.1.5 |
||||||||||||||
|
cOpticalParamHighAlarmSev
This object is used to specify a severity level associated
with the high alarm threshold given by the cOpticalParamHighAlarmThresh object. The values 'notAlarmed', 'notReported', and 'cleared' do not apply. … |
OpticalAlarmSeverityr/w Textual Convention: OpticalAlarmSeverity EnumerationType Values:
|
.1.3.6.1.4.1.9.9.264.1.1.1.1.6 |
||||||||||||||
|
cOpticalParamHighWarningThresh
This object is used to set a high warning threshold on
the optical parameter being monitored. A threshold crossing condition will be indicated if the value given by cOpticalParameterValue goes from below … |
OpticalParameterValuer/w Textual Convention: OpticalParameterValue Integer32Type Constraints: range: -1000000..1000000 |
.1.3.6.1.4.1.9.9.264.1.1.1.1.7 |
||||||||||||||
|
cOpticalParamHighWarningSev
This object is used to specify a severity level associated
with the high warning threshold given by the cOpticalParamHighWarningThresh object. The values 'critical', 'major', and 'cleared' do not apply. T… |
OpticalAlarmSeverityr/w Textual Convention: OpticalAlarmSeverity EnumerationType Values:
|
.1.3.6.1.4.1.9.9.264.1.1.1.1.8 |
||||||||||||||
|
cOpticalParamLowAlarmThresh
This object is used to set a low alarm threshold on the
optical parameter being monitored. An alarm condition will be raised if the value given by cOpticalParameterValue goes from above the value configur… |
OpticalParameterValuer/w Textual Convention: OpticalParameterValue Integer32Type Constraints: range: -1000000..1000000 |
.1.3.6.1.4.1.9.9.264.1.1.1.1.9 |
||||||||||||||
|
cOpticalParamLowAlarmSev
This object is used to specify a severity level associated
with the low alarm threshold given by the cOpticalParamLowAlarmThresh object. The values 'notAlarmed', 'notReported', and 'cleared' do not apply. … |
OpticalAlarmSeverityr/w Textual Convention: OpticalAlarmSeverity EnumerationType Values:
|
.1.3.6.1.4.1.9.9.264.1.1.1.1.10 |
||||||||||||||
|
cOpticalParamLowWarningThresh
This object is used to set a low warning threshold on
the optical parameter being monitored. A threshold crossing condition will be indicated if the value given by cOpticalParameterValue goes from above t… |
OpticalParameterValuer/w Textual Convention: OpticalParameterValue Integer32Type Constraints: range: -1000000..1000000 |
.1.3.6.1.4.1.9.9.264.1.1.1.1.11 |
||||||||||||||
|
cOpticalParamLowWarningSev
This object is used to specify a severity level associated
with the low warning threshold given by the cOpticalParamLowWarningThresh object. The values 'critical', 'major', and 'cleared' do not apply. The… |
OpticalAlarmSeverityr/w Textual Convention: OpticalAlarmSeverity EnumerationType Values:
|
.1.3.6.1.4.1.9.9.264.1.1.1.1.12 |
||||||||||||||
|
cOpticalParamAlarmStatus
This object is used to indicate the current status of
the thresholds for the monitored optical parameter on the interface. If a threshold is currently being exceeded on the interface, the corresponding bi… |
OpticalAlarmStatus Textual Convention: OpticalAlarmStatus OctetStringType Constraints: range: 1 |
.1.3.6.1.4.1.9.9.264.1.1.1.1.13 |
||||||||||||||
|
cOpticalParamAlarmCurMaxThresh
This object indicates the threshold value of the highest
severity threshold that is currently being exceeded on the interface, for the optical parameter. If no threshold value is currently being exceeded, then the value… |
OpticalParameterValue Textual Convention: OpticalParameterValue Integer32Type Constraints: range: -1000000..1000000 |
.1.3.6.1.4.1.9.9.264.1.1.1.1.14 |
||||||||||||||
|
cOpticalParamAlarmCurMaxSev
This object indicates the maximum severity of any thresholds
that are currently being exceeded on the interface, for the optical parameter. |
OpticalAlarmSeverity Textual Convention: OpticalAlarmSeverity EnumerationType Values:
|
.1.3.6.1.4.1.9.9.264.1.1.1.1.15 |
||||||||||||||
|
cOpticalParamAlarmLastChange
This object specifies the value of sysUpTime at the last time
a threshold related to a particular optical parameter was exceeded or cleared on the interface. |
SNMPv2-TCTimeStamp Textual Convention: SNMPv2-TCTimeStamp Unsigned32 |
.1.3.6.1.4.1.9.9.264.1.1.1.1.16 |
||||||||||||||
|
cOpticalMon15MinValidIntervals
This object gives the number of previous 15 minute
intervals for which valid performance monitoring data has been stored on the interface. The value of this object will be n (where n is the maximum number… |
Unsigned32 Constraints: range: 0-96 |
.1.3.6.1.4.1.9.9.264.1.1.1.1.17 |
||||||||||||||
|
cOpticalMon24HrValidIntervals
This object gives the number of previous 24 hour
intervals for which valid performance monitoring data has been stored on the interface. The value of this object will be 0 if the measurement was (re-)star… |
Unsigned32 Constraints: range: 0-1 |
.1.3.6.1.4.1.9.9.264.1.1.1.1.18 |
||||||||||||||
|
cOpticalParamThreshSource
This object indicates if the current value of a particular
threshold in this entry is user configured value or it is a system default value. It also allows user to specify the list of thresholds for this entry which s… |
Bitsr/w Enumerated Values:
|
.1.3.6.1.4.1.9.9.264.1.1.1.1.19 |
cOpticalMonIfTable
table.1.3.6.1.4.1.9.9.264.1.1.5
·
1 row entry
·
1 columns
This table contains the list of optical interfaces populated in cOpticalMonTable.
An entry containing the information for a particular optical interface.
Indexes
IF-MIBifIndex
| Column | Syntax | OID |
|---|---|---|
|
cOpticalMonIfTimeInSlot
This object indicates when this optical transceiver was detected by the
system. |
secondsSNMPv2-SMIUnsigned32 Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.9.9.264.1.1.5.1.1 |
cOpticalPMCurrentTable
table.1.3.6.1.4.1.9.9.264.1.2.1
·
1 row entry
·
8 columns
This table contains performance monitoring data for the various optical parameters, collected over the current 15 minute or the current 24 hour interval.
An entry in the cOpticalPMCurrentTable. It contains
performance monitoring data for a monitored optical
parameter at an interface, collected over the current 15
minute or the current 24 hour interval.
Note …
performance monitoring data for a monitored optical
parameter at an interface, collected over the current 15
minute or the current 24 hour interval.
Note …
Indexes
cOpticalPMCurrentPeriod IF-MIBifIndex cOpticalPMCurrentDirection cOpticalPMCurrentLocation cOpticalPMCurrentParamType
| Column | Syntax | OID | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
cOpticalPMCurrentPeriod
This object indicates whether the optical parameter values
given in this entry are collected over the current 15 minute or the current 24 hour interval. |
OpticalPMPeriod Textual Convention: OpticalPMPeriod EnumerationType Values:
|
.1.3.6.1.4.1.9.9.264.1.2.1.1.1 |
||||||||||||||
|
cOpticalPMCurrentDirection
This object indicates the direction monitored for the optical
interface, in this entry. |
OpticalIfDirection Textual Convention: OpticalIfDirection EnumerationType Values:
|
.1.3.6.1.4.1.9.9.264.1.2.1.1.2 |
||||||||||||||
|
cOpticalPMCurrentLocation
This object indicates whether the optical characteristics are
measured before or after adjustment (e.g. optical amplification or attenuation), at this interface. |
OpticalIfMonLocation Textual Convention: OpticalIfMonLocation EnumerationType Values:
|
.1.3.6.1.4.1.9.9.264.1.2.1.1.3 |
||||||||||||||
|
cOpticalPMCurrentParamType
This object specifies the optical parameter that is being
monitored, in this entry. |
OpticalParameterType Textual Convention: OpticalParameterType EnumerationType Values:
|
.1.3.6.1.4.1.9.9.264.1.2.1.1.4 |
||||||||||||||
|
cOpticalPMCurrentMaxParam
This object gives the maximum value measured for the monitored
optical parameter, in the current 15 minute or the current 24 hour interval. |
OpticalParameterValue Textual Convention: OpticalParameterValue Integer32Type Constraints: range: -1000000..1000000 |
.1.3.6.1.4.1.9.9.264.1.2.1.1.5 |
||||||||||||||
|
cOpticalPMCurrentMinParam
This object gives the minimum value measured for the monitored
optical parameter, in the current 15 minute or the current 24 hour interval. |
OpticalParameterValue Textual Convention: OpticalParameterValue Integer32Type Constraints: range: -1000000..1000000 |
.1.3.6.1.4.1.9.9.264.1.2.1.1.6 |
||||||||||||||
|
cOpticalPMCurrentMeanParam
This object gives the average value of the monitored
optical parameter, in the current 15 minute or the current 24 hour interval. |
OpticalParameterValue Textual Convention: OpticalParameterValue Integer32Type Constraints: range: -1000000..1000000 |
.1.3.6.1.4.1.9.9.264.1.2.1.1.7 |
||||||||||||||
|
cOpticalPMCurrentUnavailSecs
This object is used to indicate the number of seconds,
in the current 15 minute or the current 24 hour interval, for which the optical performance data is not accounted for. In the receive direction, the … |
Integer32 Constraints: range: 0-86400 |
.1.3.6.1.4.1.9.9.264.1.2.1.1.8 |
cOpticalPMIntervalTable
table.1.3.6.1.4.1.9.9.264.1.2.2
·
1 row entry
·
9 columns
This table stores performance monitoring data for the
various optical parameters, collected over previous
intervals.
This table can have entries for one complete 24 hour
interval and up to 96 complete 15 minute
intervals. A system is required to store at least
4 completed 15 minute intervals. The number of valid
15 minute intervals in this table is indicated by the
cOpticalMon15MinValidIntervals object and the number of
valid 24 hour intervals is indicated by the
cOpticalMon24HrValidIntervals object.
An entry in the cOpticalPMIntervalTable. It contains
performance monitoring data for an optical parameter,
collected over a previous interval.
Note that the set of monitored optical parameters may vary
base…
performance monitoring data for an optical parameter,
collected over a previous interval.
Note that the set of monitored optical parameters may vary
base…
Indexes
cOpticalPMIntervalPeriod cOpticalPMIntervalNumber IF-MIBifIndex cOpticalPMIntervalDirection cOpticalPMIntervalLocation cOpticalPMIntervalParamType
| Column | Syntax | OID | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
cOpticalPMIntervalPeriod
This object indicates whether the optical parameter values,
given in this entry, are collected over a period of 15 minutes or 24 hours. |
OpticalPMPeriod Textual Convention: OpticalPMPeriod EnumerationType Values:
|
.1.3.6.1.4.1.9.9.264.1.2.2.1.1 |
||||||||||||||
|
cOpticalPMIntervalNumber
A number between 1 and 96, which identifies the
interval for which the set of optical parameter values is available. The interval identified by 1 is the most recently completed 15 minute or 24 hour interval, and the int… |
Integer32 Constraints: range: 1-96 |
.1.3.6.1.4.1.9.9.264.1.2.2.1.2 |
||||||||||||||
|
cOpticalPMIntervalDirection
This object indicates the direction monitored for the optical
interface, in this entry. |
OpticalIfDirection Textual Convention: OpticalIfDirection EnumerationType Values:
|
.1.3.6.1.4.1.9.9.264.1.2.2.1.3 |
||||||||||||||
|
cOpticalPMIntervalLocation
This object indicates whether the optical characteristics
are measured before or after adjustment (e.g. optical amplification or attenuation), at this interface. |
OpticalIfMonLocation Textual Convention: OpticalIfMonLocation EnumerationType Values:
|
.1.3.6.1.4.1.9.9.264.1.2.2.1.4 |
||||||||||||||
|
cOpticalPMIntervalParamType
This object specifies the optical parameter that is being
monitored, in this entry. |
OpticalParameterType Textual Convention: OpticalParameterType EnumerationType Values:
|
.1.3.6.1.4.1.9.9.264.1.2.2.1.5 |
||||||||||||||
|
cOpticalPMIntervalMaxParam
This object gives the maximum value measured for the optical
parameter, in a particular 15 minute or 24 hour interval. |
OpticalParameterValue Textual Convention: OpticalParameterValue Integer32Type Constraints: range: -1000000..1000000 |
.1.3.6.1.4.1.9.9.264.1.2.2.1.6 |
||||||||||||||
|
cOpticalPMIntervalMinParam
This object gives the minimum value measured for the optical
parameter, in a particular 15 minute or 24 hour interval. |
OpticalParameterValue Textual Convention: OpticalParameterValue Integer32Type Constraints: range: -1000000..1000000 |
.1.3.6.1.4.1.9.9.264.1.2.2.1.7 |
||||||||||||||
|
cOpticalPMIntervalMeanParam
This object gives the average value of the measured optical
parameter, in a particular 15 minute or 24 hour interval. |
OpticalParameterValue Textual Convention: OpticalParameterValue Integer32Type Constraints: range: -1000000..1000000 |
.1.3.6.1.4.1.9.9.264.1.2.2.1.8 |
||||||||||||||
|
cOpticalPMIntervalUnavailSecs
This object is used to indicate the number of seconds,
in the particular 15 minute or 24 hour interval, for which the optical performance data is not accounted for. In the receive direction, the performan… |
Integer32 Constraints: range: 0-86400 |
.1.3.6.1.4.1.9.9.264.1.2.2.1.9 |