cOpticalMon15MinValidIntervals
CISCO-OPTICAL-MONITOR-MIB ·
.1.3.6.1.4.1.9.9.264.1.1.1.1.17
Object
column
Unsigned32
This object gives the number of previous 15 minute
intervals for which valid performance monitoring data
has been stored on the interface.
The value of this object will be n (where n is the maximum
number of 15 minute intervals supported at this interface),
unless the measurement was (re-)started within the last
(nx15) minutes, in which case the value will be the
number of previous 15 minute intervals for which the agent
has some data.
Context
- MIB
- CISCO-OPTICAL-MONITOR-MIB
- OID
.1.3.6.1.4.1.9.9.264.1.1.1.1.17- Type
- column
- Access
- readonly
- Status
- current
- Parent
- cOpticalMonEntry
- Table
- cOpticalMonTable
- Siblings
- 18
Syntax
Unsigned32
Values & Constraints
Object Constraints
range: 0-96
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cOpticalMonDirection This object indicates the direction monitored for the
optical interface, in this entry. | column | OpticalIfDirection | .1.3.6.1.4.1.9.9.264.1.1.1.1.1 |
| cOpticalParamLowAlarmSev This object is used to specify a severity level associated
with the low alarm threshold given by the
cOpticalParamLowAlarmThresh object. The values 'notAlarmed',
'notReported', an… | column | OpticalAlarmSeverity | .1.3.6.1.4.1.9.9.264.1.1.1.1.10 |
| cOpticalParamLowWarningThresh This object is used to set a low warning threshold on
the optical parameter being monitored.
A threshold crossing condition will be indicated if the value
given by … | column | OpticalParameterValue | .1.3.6.1.4.1.9.9.264.1.1.1.1.11 |
| cOpticalParamLowWarningSev This object is used to specify a severity level associated
with the low warning threshold given by the
cOpticalParamLowWarningThresh object. The values 'critical',
'major', and 'c… | column | OpticalAlarmSeverity | .1.3.6.1.4.1.9.9.264.1.1.1.1.12 |
| cOpticalParamAlarmStatus This object is used to indicate the current status of
the thresholds for the monitored optical parameter
on the interface.
If a threshold is currently being exceede… | column | OpticalAlarmStatus | .1.3.6.1.4.1.9.9.264.1.1.1.1.13 |
| cOpticalParamAlarmCurMaxThresh This object indicates the threshold value of the highest
severity threshold that is currently being exceeded
on the interface, for the optical parameter.
If no threshold value is … | column | OpticalParameterValue | .1.3.6.1.4.1.9.9.264.1.1.1.1.14 |
| cOpticalParamAlarmCurMaxSev This object indicates the maximum severity of any thresholds
that are currently being exceeded on the interface, for the
optical parameter. | column | OpticalAlarmSeverity | .1.3.6.1.4.1.9.9.264.1.1.1.1.15 |
| cOpticalParamAlarmLastChange This object specifies the value of sysUpTime at the last time
a threshold related to a particular optical parameter was
exceeded or cleared on the interface. | column | SNMPv2-TCTimeStamp | .1.3.6.1.4.1.9.9.264.1.1.1.1.16 |
| cOpticalMon24HrValidIntervals This object gives the number of previous 24 hour
intervals for which valid performance monitoring data
has been stored on the interface.
The value of this object wi… | column | Unsigned32 | .1.3.6.1.4.1.9.9.264.1.1.1.1.18 |
| cOpticalParamThreshSource This object indicates if the current value of a particular
threshold in this entry is user configured value or it is
a system default value. It also allows user to specify
the l… | column | Bits | .1.3.6.1.4.1.9.9.264.1.1.1.1.19 |
| cOpticalMonLocation This object indicates whether the optical characteristics are
measured before or after adjustment (e.g. optical amplification
or attenuation), at this interface. | column | OpticalIfMonLocation | .1.3.6.1.4.1.9.9.264.1.1.1.1.2 |
| cOpticalMonParameterType This object specifies the optical parameter that is being
monitored in this entry. | column | OpticalParameterType | .1.3.6.1.4.1.9.9.264.1.1.1.1.3 |
| cOpticalParameterValue This object gives the value measured for the particular
optical parameter specified by the cOpticalMonParameterType
object. | column | OpticalParameterValue | .1.3.6.1.4.1.9.9.264.1.1.1.1.4 |
| cOpticalParamHighAlarmThresh This object is used to set a high alarm threshold on the
optical parameter being monitored.
An alarm condition will be raised if the value given by
cOpticalParamete… | column | OpticalParameterValue | .1.3.6.1.4.1.9.9.264.1.1.1.1.5 |
| cOpticalParamHighAlarmSev This object is used to specify a severity level associated
with the high alarm threshold given by the
cOpticalParamHighAlarmThresh object. The values 'notAlarmed',
'notReported', … | column | OpticalAlarmSeverity | .1.3.6.1.4.1.9.9.264.1.1.1.1.6 |
| cOpticalParamHighWarningThresh This object is used to set a high warning threshold on
the optical parameter being monitored.
A threshold crossing condition will be indicated if the value
given by… | column | OpticalParameterValue | .1.3.6.1.4.1.9.9.264.1.1.1.1.7 |
| cOpticalParamHighWarningSev This object is used to specify a severity level associated
with the high warning threshold given by the
cOpticalParamHighWarningThresh object. The values 'critical',
'major', and … | column | OpticalAlarmSeverity | .1.3.6.1.4.1.9.9.264.1.1.1.1.8 |
| cOpticalParamLowAlarmThresh This object is used to set a low alarm threshold on the
optical parameter being monitored.
An alarm condition will be raised if the value given by
cOpticalParameter… | column | OpticalParameterValue | .1.3.6.1.4.1.9.9.264.1.1.1.1.9 |