HMPRIV-MGMT-SNMP-MIB Table View

This table contains variables for a closer description of
a group.

hmSysGroupEntry row .1.3.6.1.4.1.248.14.1.1.9.1

The entry of the hmSysGroupTable.

Indexes

No indexes recorded

Column	Syntax	OID
hmSysGroupID index to identify an interface card. This value is never greater than hmSysGroupCapacity.	Integer32 Constraints: range: 0-10000	.1.3.6.1.4.1.248.14.1.1.9.1.1
hmSysGroupType Type of interface card.	Enumeration Constraints: range: 1-3600	.1.3.6.1.4.1.248.14.1.1.9.1.2
hmSysGroupDescription Description of interface card.	SNMPv2-TCDisplayString Enumerated Values: 1 enable 2 disable Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.1.9.1.3
hmSysGroupHwVersion Hardware version of interface card.	SNMPv2-TCDisplayString Enumerated Values: 1 true 2 false Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.1.9.1.4
hmSysGroupSwVersion Software version of interface card.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.1.9.1.5
hmSysGroupModuleMap This string represents the current configuration of a group, encoded as an octet string. Each module is represented by a single octet. If the value of a single octet is the ascii representation of the character '1', it …	SNMPv2-TCDisplayString Enumerated Values: 1 all 2 bc 3 bc-mc 4 bc-mc-uuc Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.1.9.1.6
hmSysGroupAction This object, when read, always returns a value of other(1). A value of reset(2) has the same effect as a power-on sequence (coldstart). When set to resetStats(3), a reset of all statistic counters of the card's ports wi…	Enumerationr/w Enumerated Values: 1 bytebased 2 packetbased	.1.3.6.1.4.1.248.14.1.1.9.1.7
hmSysGroupActionResult Result of the last activated action. A value of zero indicates that the result is ok. Bits set in the result indicate error conditions.	SNMPv2-SMIInteger32 Constraints: range: 0-1000000000	.1.3.6.1.4.1.248.14.1.1.9.1.8
hmSysGroupIsolateMode Setting this variable to enable(1) separates the group from the rest of the chassis, so that it will act like a standalone-switch.	Enumerationr/w Enumerated Values: 1 all 2 bc 3 bc-mc 4 bc-mc-uuc	.1.3.6.1.4.1.248.14.1.1.9.1.9
hmSysGroupSerialNum The serial number provided by vendor (ASCII).	SNMPv2-TCDisplayString Enumerated Values: 1 bytebased 2 packetbased Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.1.9.1.10
hmSysGroupActionDelayPreset Time in seconds until a reset(2) or hotRestart(10) that was triggered over the hmSysGroupAction object is executed. Writing a zero will cancel any scheduled reset.	Integer32r/w Constraints: range: 0-1000000000	.1.3.6.1.4.1.248.14.1.1.9.1.11
hmSysGroupActionDelayCurrent If a delayed reset is scheduled this object will incrementing from the start value to zero.	Integer32 Constraints: range: 0-10000	.1.3.6.1.4.1.248.14.1.1.9.1.12

This table contains variables for a closer description of a
module.

hmSysModuleEntry row .1.3.6.1.4.1.248.14.1.1.10.1

The entry of the hmSysModuleTable.

Indexes

No indexes recorded

Column	Syntax	OID
hmSysModGroupID index to identify an interface card. This value is never greater than hmSysGroupCapacity.	Integer32 Enumerated Values: 1 enable 2 disable 3 unsupported	.1.3.6.1.4.1.248.14.1.1.10.1.1
hmSysModID index to identify a module on an interface card. This value is never greater than hmSysGroupModuleCapacity.	Integer32 Enumerated Values: 1 enable 2 disable 3 unsupported	.1.3.6.1.4.1.248.14.1.1.10.1.2
hmSysModType Type of a module.	Enumeration Enumerated Values: 1 admitAll 2 admitOnlyVlanTagged 3 admitOnlyUntagged	.1.3.6.1.4.1.248.14.1.1.10.1.3
hmSysModDescription Description of the module.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.1.10.1.4
hmSysModVersion version of the module.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.1.10.1.5
hmSysModNumOfPorts The numberOfPorts is the number of ports contained within the module. Within each module, the ports are uniquely numbered in the range from 1 to numberOfPorts.	SNMPv2-SMIInteger32 Constraints: range: 1-8	.1.3.6.1.4.1.248.14.1.1.10.1.6
hmSysModFirstMauIndex value of the first mauIndex used by the module.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.14.1.1.10.1.7
hmSysModStatus status of hot-pluggable modules, only for PowerMICE. If the value is physical(1), then the module is plugged in, if the value is configurable, the ports can be configured, but the card is absent, with the value remove(3…	Enumerationr/w	.1.3.6.1.4.1.248.14.1.1.10.1.8
hmSysModSerialNum The serial number provided by vendor (ASCII).	SNMPv2-TCDisplayString Enumerated Values: 1 noAction 2 resetStats Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.1.10.1.9
hmSysModAdminState Enable or disable the module. If disabled, module plugged in this slot will not be activated.	Enumerationr/w Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.248.14.1.1.10.1.10

This table contains variables for each interface of
the switch.

hmInterfaceEntry row .1.3.6.1.4.1.248.14.1.1.11.1

The entry of the hmInterfaceTable.

Indexes

No indexes recorded

Column	Syntax	OID
hmIfaceGroupID index to identify an interface card. This value is never greater than hmSysGroupCapacity.	Integer32	.1.3.6.1.4.1.248.14.1.1.11.1.1
hmIfaceID index to identify an interface within an interface card.	Integer32	.1.3.6.1.4.1.248.14.1.1.11.1.2
hmIfaceStpEnable Enable or disable spanning tree protocol.	Enumerationr/w Constraints: range: 1-7	.1.3.6.1.4.1.248.14.1.1.11.1.3
hmIfaceLinkType Describes the link type of the interface.	Enumerationr/w Constraints: range: 1-128	.1.3.6.1.4.1.248.14.1.1.11.1.4
hmIfaceAction This object, when read, always returns a value of noAction(1). When set to resetStats(2), a reset of all statistic counters within this interfacecard will be forced.	Enumerationr/w Enumerated Values: 1 non-sfp 6 fiberjack 7 lc 8 mt-rj 11 optical-pigtail 33 copper-pigtail	.1.3.6.1.4.1.248.14.1.1.11.1.5
hmIfaceNextHopMacAddress The macaddress of the next switch agent reachable via this interface. If the value is 0:0:0:0:0:0, no other switch is seen via this interface.	SNMPv2-TCMacAddress Enumerated Values: 1 ge-1000-base-sx 2 ge-1000-base-lx 4 ge-1000-base-cx 8 ge-1000-base-t 9 unsupported 10 oc3-mm-sr 11 oc3-sm-ir 12 oc3-sm-lr 13 oc12-mm-sr 14 oc12-sm-ir 15 oc12-sm-lr 16 oc48-sr 17 oc48-ir 18 oc48-lr 30 xfp-10gbase-sr 31 xfp-10gbase-lr 32 xfp-10gbase-er 40 microfx 41 pof Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.248.14.1.1.11.1.6
hmIfaceFlowControl Enables or disables flow control per port	Enumerationr/w	.1.3.6.1.4.1.248.14.1.1.11.1.7
hmIfacePriorityThreshold This object is used to support the dot1dTrafficClassTable. It defines the thresholds of the available priority-classes. Starting at MACH Release 2.20 this variable is not used any more.	Integer32r/w	.1.3.6.1.4.1.248.14.1.1.11.1.8
hmIfaceName User configurable textual description of the interface. On devices which support Power over Ethernet (IEEE 802.af), this object is mapped to pethPsePortType of the RFC3621 MIB.	OctetStringr/w	.1.3.6.1.4.1.248.14.1.1.11.1.9
hmIfaceTrunkID If the value of this variable is greater 0 then it belongs to the link aggregation instance with the same index. If the value is 0 no link aggregation uses this interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.14.1.1.11.1.10
hmIfacePrioTOSEnable Enable or disable Priority setting from IP TOS field.	Enumerationr/w	.1.3.6.1.4.1.248.14.1.1.11.1.11
hmIfaceBcastLimit Broadcast rate: maximum number of broadcasts to be sent on this port within one second, use 0 for no limitation.	Integer32r/w	.1.3.6.1.4.1.248.14.1.1.11.1.12
hmIfaceUtilization The best estimate of the mean physical layer network utilization on this interface during the last sampling interval, in hundredths of a percent. The first historyControlInterval (rfc1757) of this interface is used as …	Integer32	.1.3.6.1.4.1.248.14.1.1.11.1.13
hmIfaceUtilizationControlInterval The interval in seconds over which the data is sampled for hmIfaceUtilization. This interval can be any number of seconds between 1 and 3600 (1 hour). The first historyControlInterval (rfc1757) of this interface is used…	Integer32	.1.3.6.1.4.1.248.14.1.1.11.1.14
hmIfaceStpBpduGuardEnable Enabled or disabled the BPDU guard functionality per port. If BPDU guard functionality are global enabled (hmSysStpBPDUGuardEnable=enable(1)), and BPDU guard are enabled per port (hmIfaceStpBpduGuardEnable=enable(1)) an…	Enumerationr/w	.1.3.6.1.4.1.248.14.1.1.11.1.15
hmIfaceStpBpduGuardStatus Advertised the state of BPDU guard functionality for this port. If BPDU guard functionality fot this port is disabled or guard functionality is enabled, but no BPDUs are received on this port, then hmIfaceStpBpduGuard…	Enumeration	.1.3.6.1.4.1.248.14.1.1.11.1.16
hmIfaceCapability Capability of the interface coded as an integer value with each bit representing a special capability. Meaning of the bits: Bit 0: cabletest capability Bit 1: realtime capability according to IEEE 1588.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.14.1.1.11.1.17
hmIfaceIngressLimiterMode The ingress limiter can work in different modes. Mode all limits the complete ingress traffic. Mode bc limits only the ingress broadcast traffic. Mode bc_mc limits the ingress broadcast and multicast traffic. Mode bc_mc…	Enumerationr/w	.1.3.6.1.4.1.248.14.1.1.11.1.18
hmIfaceIngressLimiterCalculationMode The ingress limiter can measure the traffic on a bytes per second or on a packets per second basis. The limiter calculation mode is hardware dependend. Not all modes are available on every hardware.	Enumerationr/w Enumerated Values: 1 ok 2 warning 3 alarm	.1.3.6.1.4.1.248.14.1.1.11.1.19
hmIfaceIngressLimiterRate The rate of the ingress limiter. The value 0 disables the limiter.	Integer32r/w	.1.3.6.1.4.1.248.14.1.1.11.1.20
hmIfaceEgressLimiterMode The egress limiter can work in different modes. Mode all limits the complete egress traffic. Mode bc limits only the egress broadcast traffic. Mode bc_mc limits the egress broadcast and multicast traffic. Mode bc_mc_uuc…	Enumerationr/w Constraints: range: 0-11	.1.3.6.1.4.1.248.14.1.1.11.1.21
hmIfaceEgressLimiterCalculationMode The egress limiter can measure the traffic on a bytes per second or on a packets per second basis. The limiter calculation mode is hardware dependend. Not all modes are available on every hardware.	Enumerationr/w Constraints: range: 0-16	.1.3.6.1.4.1.248.14.1.1.11.1.22
hmIfaceEgressLimiterRate The rate of the egress limiter. The value 0 disables the limiter.	Integer32r/w	.1.3.6.1.4.1.248.14.1.1.11.1.23
hmIfaceUtilizationAlarmUpperThreshold Surveys the interface utilization hmIfaceUtilization and generates an alarm for this interfaces, if the given limit is exceeded. A value of 0 disables the alarm generation.	Integer32r/w	.1.3.6.1.4.1.248.14.1.1.11.1.24
hmIfaceUtilizationAlarmLowerThreshold Surveys the interface utilization hmInfaceUtilization and removes the alarm condition for this interfaces, if the utilization value is below the given limit. A value of 0 disables the alarm removal.	Integer32r/w	.1.3.6.1.4.1.248.14.1.1.11.1.25
hmIfaceUtilizationAlarmCondition The alarm condition is given (true), if the given hmIfaceUtilizationAlarmUpperThreshold limit is exceeded by the interface utilization. The alarm condition will be removed, when the interface utilization falls below th…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.248.14.1.1.11.1.26
hmIfaceCableCrossing This variable configures the cable crossing on twisted pair cables. When set to 'enable', the port uses the crossover mode. When set to 'disable', the port does not use the crossover mode. 'Unsupported' is shown, if a p…	Enumerationr/w	.1.3.6.1.4.1.248.14.1.1.11.1.27
hmIfacePhyFastLinkDetection This variable configures the PHY specific fast link detection feature on this port. 'Unsupported' is shown, if a port does not support this feature. It is not possible to set 'unsupported' to any type of port.	Enumerationr/w	.1.3.6.1.4.1.248.14.1.1.11.1.28
hmIfaceAcceptableFrameTypesobsolete This object is 'obsolete' and is replaced by hmIfaceExtAcceptableFrameTypes. When this is admitOnlyVlanTagged(2) the device will discard untagged frames received on this port. When admitOnlyUntagged(3), the device will…	Enumerationr/w	.1.3.6.1.4.1.248.14.1.1.11.1.29

This table contains variables for each trunk of
the switch.

hmTrunkEntry row .1.3.6.1.4.1.248.14.1.1.12.1

The entry of the hmTrunkTable.

Indexes

No indexes recorded

Column	Syntax	OID
hmTrunkID Index to identify a link aggregation instance	Integer32	.1.3.6.1.4.1.248.14.1.1.12.1.1
hmTrunkInterfaces List of interfaces which are aggregated in the trunk. each octet pair contains the slotID and interfaceID. Interfaces are added or deleteted using the variable hmIfaceTrunkID.	OctetString Enumerated Values: 1 admitAll 2 admitOnlyVlanTagged 3 admitOnlyUntagged	.1.3.6.1.4.1.248.14.1.1.12.1.2
hmTrunkName Textual description of the trunk	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.1.12.1.3
hmTrunkAction action according to hmIfaceAction which is performed for all interfaces in the trunk	Enumerationr/w	.1.3.6.1.4.1.248.14.1.1.12.1.4
hmTrunkAdminStatus The desired state of the trunk. if this variable is set to down(2), all interfaces which are aggregated in the trunk are switched off simultaneously. Reading this variable returns up(1) if at least one interface of the…	Enumerationr/w Constraints: range: 1-2	.1.3.6.1.4.1.248.14.1.1.12.1.5
hmTrunkOperStatus The operational state of the trunk. Reading this variable returns up(1) if at least one interface of the trunk is operational (up).	Enumeration Constraints: range: 1-8	.1.3.6.1.4.1.248.14.1.1.12.1.6
hmTrunkLastChange Time since system boot when there was a change in either the operational state of the trunk or the list of aggregated interfaces.	SNMPv2-SMITimeTicks Enumerated Values: 1 ok 2 failed 3 notInstalled 4 unknown Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.248.14.1.1.12.1.7

This table contains variables for each SFP.

hmSFPEntry row .1.3.6.1.4.1.248.14.1.1.13.1

Entry for a detected SFP.

Indexes

No indexes recorded

Column	Syntax	OID
hmSfpGroupID Index to identify a module. This value is never greater than hmSysGroupModuleCapacity.	Integer32	.1.3.6.1.4.1.248.14.1.1.13.1.1
hmSfpID Index to identify an interface within a module. This value is never greater than hmSysModulePortCapacity.	Integer32	.1.3.6.1.4.1.248.14.1.1.13.1.2
hmSfpConnector The SFP's Connector Type.	Enumeration	.1.3.6.1.4.1.248.14.1.1.13.1.3
hmSfpTransceiver The SFP's Transceiver type.	Enumeration	.1.3.6.1.4.1.248.14.1.1.13.1.4
hmSfpVendorOUI The SFP's vendor IEEE company ID (OUI).	OctetString	.1.3.6.1.4.1.248.14.1.1.13.1.5
hmSfpVendorName The SFP's vendor name (ASCII).	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.1.13.1.6
hmSfpPartNumber The SFP's part description number (ASCII).	SNMPv2-TCDisplayString Constraints: range: 1-2 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.1.13.1.7
hmSfpPartRev The SFP's part revision number (ASCII).	SNMPv2-TCDisplayString Constraints: range: 1-4 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.1.13.1.8
hmSfpSerialNum The SFP's serial number provided by vendor (ASCII).	SNMPv2-TCDisplayString Enumerated Values: 1 ok 2 failed Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.1.13.1.9
hmSfpDateCode The SFP's vendor manufacturing date code. Format is YY:MM:DD.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.1.13.1.10
hmSfpBitRate The SFP's nominal bitrate in units of MBits/sec. Contains -1 in case of a device read error.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.14.1.1.13.1.11
hmSfpTemperature This signed integer is used to identify the temperature within the SFP in units of centigrade (celsius). Contains -1000 in case of a device read error.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.14.1.1.13.1.12
hmSfpTxPower The SFP's internally measured Tx Power in units of milliWatts. (ASCII representation of floating point number).	SNMPv2-TCDisplayString Constraints: range: 1-128 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.1.13.1.13
hmSfpRxPower The SFP's internally measured Rx Power in units of milliWatts. (ASCII representation of floating point number).	SNMPv2-TCDisplayString Constraints: range: 0-9 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.1.13.1.14
hmSfpTxPowerInt The SFP's internally measured Tx Power in units of 1/10 microWatts.	SNMPv2-SMIInteger32 Enumerated Values: 1 other 2 invalid 3 permanent 4 deleteOnReset 5 deleteOnTimeout Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.14.1.1.13.1.15
hmSfpRxPowerInt The SFP's internally measured Rx Power in units of 1/10 microWatts.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.14.1.1.13.1.16
hmSfpRxPowerState The state of the SFP's internally measured Rx.	Enumeration	.1.3.6.1.4.1.248.14.1.1.13.1.17
hmSfpInfoVersion Version of SFP's Hirschmann Information. Contains -1 in case of a device read error.	SNMPv2-SMIInteger32 Constraints: range: 0-3	.1.3.6.1.4.1.248.14.1.1.13.1.20
hmSfpInfoPartNumber Part Number of SFP's Hirschmann Information.	OctetString Constraints: range: 2-100	.1.3.6.1.4.1.248.14.1.1.13.1.21
hmSfpInfoPartId Part Identifier of SFP's Hirschmann Information.	OctetString	.1.3.6.1.4.1.248.14.1.1.13.1.22
hmSfpInfoMagic 1, if SFP contains vendor specific information by Hirschmann, otherwise 0.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.14.1.1.13.1.23
hmSfpSupported Indicates if the local agent supports this SFP.	SNMPv2-TCTruthValue Constraints: range: 0-7 Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.248.14.1.1.13.1.24
hmSfpMaxLength-fiber-9 Max. usable length for the cable type '9/125 micrometer fiber' with this SFP in units of meters.	SNMPv2-SMIInteger32 Constraints: range: 0-7	.1.3.6.1.4.1.248.14.1.1.13.1.30
hmSfpMaxLength-fiber-50 Max. usable length for the cable type '50/125 micrometer fiber' with this SFP in units of meters.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.14.1.1.13.1.31
hmSfpMaxLength-fiber-62-5 Max. usable length for the cable type '62.5/125 micrometer fiber' with this SFP in units of meters.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.14.1.1.13.1.32
hmSfpMaxLength-copper Max. usable length for the cable type 'copper' with this SFP in units of meters.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.14.1.1.13.1.33
hmSfpTxPowerdBm The SFP's internally measured Tx Power in units of dBm. (ASCII representation of floating point number).	SNMPv2-TCDisplayString Constraints: range: 1-128 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.1.13.1.34
hmSfpRxPowerdBm The SFP's internally measured Rx Power in units of dBm. (ASCII representation of floating point number).	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.1.13.1.35

This table contains variables for each interface of
the switch.

hmInterfaceExtEntry row .1.3.6.1.4.1.248.14.1.1.100.1

The entry of the hmInterfaceExtTable.

Indexes

No indexes recorded

Column	Syntax	OID
hmIfaceExtAcceptableFrameTypes When this is admitOnlyVlanTagged(2) the device will discard untagged frames received on this port. When admitOnlyUntagged(3), the device will discard any frames with a VLAN tag. When admitAll(1), all frames are accep…	Enumerationr/w	.1.3.6.1.4.1.248.14.1.1.100.1.1

This table contains all variables related to the power supply
units of the chassis/switch. For each power supply slot exists
one instance.

hmPSEntry row .1.3.6.1.4.1.248.14.1.2.1

The entry of the hmPSTable.

Indexes

No indexes recorded

Column	Syntax	OID
hmPSSysID The value of SysID is assigned so as to uniquely identify a chassis/switch among the subordinate managed objects of the system.	Integer32 Enumerated Values: 1 on 2 off	.1.3.6.1.4.1.248.14.1.2.1.1
hmPSID This Index is used to identify the associated power supply unit.	Integer32	.1.3.6.1.4.1.248.14.1.2.1.2
hmPSState Indicates the operational state of the associated power supply. If the value of this variable changes, a hmPowerSupply trap is sent.	Enumeration	.1.3.6.1.4.1.248.14.1.2.1.3
hmPSType Type of the associated power supply.	Enumeration Constraints: range: 1-7	.1.3.6.1.4.1.248.14.1.2.1.4
hmPSVersion Version of the associated power supply.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.14.1.2.1.5
hmPSDescription Description of the associated power supply.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.2.1.6
hmPSSerialNumber Serial number of the associated power supply.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.2.1.7
hmPSProductCode Product code of the associated power supply.	SNMPv2-TCDisplayString Constraints: range: 1-4 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.1.2.1.8
hmPSPowerBudget Power budget of the associated power supply.	SNMPv2-SMIInteger32 Enumerated Values: 1 enable 2 disable Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.14.1.2.1.9

This table contains all variables related to the fan units
of the chassis/switch. For each fan slot exists one instance.

hmFanEntry row .1.3.6.1.4.1.248.14.1.3.1

The entry of the hmFanTable.

Indexes

hmAUIModuleID

Column	Syntax	OID
hmFanSysID The value of SysID is assigned so as to uniquely identify a chassis among the subordinate managed objects of the system.	Integer32 Constraints: range: 1-7	.1.3.6.1.4.1.248.14.1.3.1.1
hmFanID This Index is used to identify the associated fan.	Integer32 Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.248.14.1.3.1.2
hmFanState Indicates the operational state of the associated fan.	Enumeration	.1.3.6.1.4.1.248.14.1.3.1.3

Table for assigning priority to MAC addresses

hmPrioMACAddressEntry row .1.3.6.1.4.1.248.14.1.4.10.1

The entry of the hmPrioMACAddressTable.

Indexes

No indexes recorded

Column	Syntax	OID
hmPrioMACAddress same as dot1dStaticAddress	SNMPv2-TCMacAddress Enumerated Values: 1 enable 2 disable Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.248.14.1.4.10.1.1
hmPrioMACReceivePort to be compatible with dot1dStaticTable	Integer32 Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.248.14.1.4.10.1.2
hmPrioMACPriority priority value for the frame with the specific destination MAC address. 0..7: priority 8 : disabled (no priority by MAC address) 9 : discard the frame	Integer32r/w	.1.3.6.1.4.1.248.14.1.4.10.1.3
hmPrioMACStatus status flag according to dot1dStaticStatus	Enumerationr/w	.1.3.6.1.4.1.248.14.1.4.10.1.4

Translation table for traffic classes to 802.1D-1998 priority

hmPrioTrafficClassEntry row .1.3.6.1.4.1.248.14.1.4.11.1

The entry of the hmPrioTrafficClassTable.

Indexes

No indexes recorded

Column	Syntax	OID
hmPrioTrafficClassID This index is used to identify the associated traffic class	Integer32 Constraints: range: 1-31	.1.3.6.1.4.1.248.14.1.4.11.1.1
hmPrioTrafficClassWeight With this parameter the queue mode of each traffic class can be set. 2..99: weight for WFQ (Weighted-Fair-Queuing) 100: strict priority	Integer32r/w	.1.3.6.1.4.1.248.14.1.4.11.1.2

Translation table IP-TOS priority to 802.1D-1998 priority

hmPrioTosToPrioEntry row .1.3.6.1.4.1.248.14.1.4.12.1

The entry of the hmPrioTosToPrioEntry.

Indexes

No indexes recorded

Column	Syntax	OID
hmPrioTTPTos This index is used to identify the associated TOS value	Integer32	.1.3.6.1.4.1.248.14.1.4.12.1.1
hmPrioTTPPrio This index is used to identify the associated 802.1D priority	Integer32 Constraints: range: 1-128	.1.3.6.1.4.1.248.14.1.4.12.1.2

A table containing filtering information
configured into the bridge by (local or network)
management or dynamic by GMRP or IGMP Snooping
specifying the set of ports to which
frames received from specific ports and containing
specific destination addresses are allowed to be
forwarded.  The value of zero in this table as the
port number from which frames with a specific
destination address are received, is used to
specify all ports for which there is no specific
entry in this table for that particular
destination address.	Entries are valid for
unicast and for group/broadcast addresses.

hmCurrentAddressEntry row .1.3.6.1.4.1.248.14.1.5.1

Filtering information configured into the bridge
by (local or network) management specifying the
set of ports to which frames received from a
specific port and containing a specific
destination address are allowed to be…

Indexes

No indexes recorded

Column	Syntax	OID
hmCurrentAddress The destination MAC address in a frame to which this entry's filtering information applies. This object can take the value of a unicast address, a group address or the broadcast address.	SNMPv2-TCMacAddress Enumerated Values: 1 true 2 false Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.248.14.1.5.1.1
hmCurrentAddressReceivePort Either the value '0', or the port number of the port from which a frame must be received in order for this entry's filtering information to apply. A value of zero indicates that this entry applies on all ports of the br…	Integer32	.1.3.6.1.4.1.248.14.1.5.1.2
hmCurrentAddressStaticEgressPorts The set of ports to which frames received from a specific port and destined for a specific MAC address, are allowed to be forwarded. Each octet within the value of this object specifies a set of eight ports, with the f…	OctetString	.1.3.6.1.4.1.248.14.1.5.1.3
hmCurrentAddressEgressPorts The complete set of ports, to which frames destined for this Group MAC Address are currently being forwarded. This includes Group MAC Addresses which were set statically or which were learnt by GMRP or some other dynami…	OctetString	.1.3.6.1.4.1.248.14.1.5.1.4
hmCurrentAddressStatus This object indicates the status of this entry. The default value is permanent(3). other(1) - this entry is currently in use but the conditions under which it will remain so are different from e…	Enumeration Enumerated Values: 1 initializing 2 faulty 3 disabled 4 listening 5 pre-master 6 master 7 passive 8 uncalibrated 9 slave	.1.3.6.1.4.1.248.14.1.5.1.5

This table contains all variables to mask an alarm for the
signalling relay, produced by a link. The index for a link
corresponds with ifMauIfIndex.

hmSigLinkEntry row .1.3.6.1.4.1.248.14.1.10.4.1

The entry of the hmSigLinkTable.

Indexes

No indexes recorded

Column	Syntax	OID
hmSigLinkID This index is used to identify the associated link and corresponds with ifMauIfIndex.	Integer32 Enumerated Values: 0 sec-1 1 sec-2 2 sec-4 3 sec-8 4 sec-16	.1.3.6.1.4.1.248.14.1.10.4.1.1
hmSigLinkAlarm Indicates whether an alarm for the signalling relay of the associated link will be produced or not, so you can mask the value of ifMauMediaAvailable.	Enumerationr/w Constraints: range: 2-10	.1.3.6.1.4.1.248.14.1.10.4.1.2

This table describes the topology of rs2-rings.

hmRS2TopologyEntry row .1.3.6.1.4.1.248.14.1.10.7.2.1

The entry of the hmRS2TopologyTable.

Indexes

No indexes recorded

Column	Syntax	OID
hmRS2TopologyLinkID This index is used to identify the associated link and corresponds with ifMauIfIndex.	Integer32 Enumerated Values: 0 sec-1 1 sec-2 2 sec-4 3 sec-8 4 sec-16 5 sec-32	.1.3.6.1.4.1.248.14.1.10.7.2.1.1
hmRS2TopologyIpAddress This variable can be used to set manually the next RS2 agent.	SNMPv2-SMIIpAddressr/w Enumerated Values: 1 ptpVersion1 2 ptpVersion2 Type Constraints: range: 4	.1.3.6.1.4.1.248.14.1.10.7.2.1.2

This table describes private vlan enhancements of rs2-4r devices.

hmRS4RVlanPortEntry row .1.3.6.1.4.1.248.14.1.10.15.1.1.1

The entry of the hmRS4RVlanPortTable.

Indexes

No indexes recorded

Column	Syntax	OID
hmRS4RVlanPortID This index is used to identify the port.	Integer32	.1.3.6.1.4.1.248.14.1.10.15.1.1.1.1
hmRS4RVlanPortTagFormatRstp When enabled all tags are removed when sending packets on the port (egress). When disabled tag format is not changed, but RSTP frames are sent tagged. This variable is only used if RSTP is enabled. The default value is …	Enumerationr/w Enumerated Values: 0 reserved 1 one-step 2 e2e-delay 3 p2p-delay 4 ptp2Ieee8023 5 ptp2UdpIpv4 6 ptp2UdpIpv6 7 asymmCorrection	.1.3.6.1.4.1.248.14.1.10.15.1.1.1.2

This table contains all AUI variables
that are module dependend.

hmAUIModuleEntry row .1.3.6.1.4.1.248.14.1.12.10.1

The entry of the hmAUIModuleTable.

Indexes

No indexes recorded

Column	Syntax	OID
hmAUIModuleID This index is used to identify a specific module.	Integer32	.1.3.6.1.4.1.248.14.1.12.10.1.1
hmAUIModuleDTEPowerMonitor This variable shows the DTE Power Monitor DIP switch setting on the AUI module.	Enumeration	.1.3.6.1.4.1.248.14.1.12.10.1.2

This table contains all AUI variables
that are port dependend.

hmAUIPortEntry row .1.3.6.1.4.1.248.14.1.12.11.1

The entry of the hmAUIPortTable.

Indexes

No indexes recorded

Column	Syntax	OID
hmAUIPortID This index is used to identify a specific port.	Integer32	.1.3.6.1.4.1.248.14.1.12.11.1.1
hmAUIPortDTEPower This variable shows the DTE Power value of the AUI port.	Enumeration	.1.3.6.1.4.1.248.14.1.12.11.1.2
hmAUIPortSQETest This variable shows the SQE Test DIP switch setting on the AUI port.	Enumeration	.1.3.6.1.4.1.248.14.1.12.11.1.3

This table contains address conflict detection information
on the local system known to this agent.

hmNetACDAddrEntry row .1.3.6.1.4.1.248.14.2.3.12.20.1

IP Address conflict detection information about a particular
address on the local system kown to this agent.
There may be multiple addresses configured on the system.
Entries may be created and deleted in this table by…

Indexes

hmRMAIndex

Column	Syntax	OID
hmNetACDTimeMark A TimeFilter for this entry. See the TimeFilter textual convention in IETF RFC 2021 and http://www.ietf.org/IESG/Implementations/RFC2021-Implementation.txt to see how TimeFilter works.	RMON2-MIBTimeFilter Constraints: range: 1-16	.1.3.6.1.4.1.248.14.2.3.12.20.1.1
hmNetACDAddrSubtype The type of management address identifier encoding used in the associated 'hmNetACDAddr' object.	IANA-ADDRESS-FAMILY-NUMBERS-MIBAddressFamilyNumbers Type Values: 0 other 1 ipV4 2 ipV6 3 nsap 4 hdlc 5 bbn1822 6 all802 7 e163 8 e164 9 f69 10 x121 11 ipx 12 appleTalk 13 decnetIV 14 banyanVines 15 e164withNsap 16 dns 17 distinguishedName 18 asNumber 19 xtpOverIpv4 20 xtpOverIpv6 21 xtpNativeModeXTP 22 fibreChannelWWPN 23 fibreChannelWWNN 24 gwid 25 afi 26 mplsTpSectionEndpointIdentifier 27 mplsTpLspEndpointIdentifier 28 mplsTpPseudowireEndpointIdentifier 29 mtipmultitopologyipversion4 30 mtipv6multitopologyipversion6 31 bgpSfc 16384 eigrpCommonServiceFamily 16385 eigrpIpv4ServiceFamily 16386 eigrpIpv6ServiceFamily 16387 lispCanonicalAddressFormat 16388 bgpLs 16389 fortyeightBitMac 16390 sixtyfourBitMac 16391 oui 16392 mac24 16393 mac40 16394 ipv664 16395 rBridgePortID 16396 trillNickname 16397 universallyUniqueIdentifier 16398 routingPolicyAfi 16399 mplsNamespaces 65535 reserved	.1.3.6.1.4.1.248.14.2.3.12.20.1.3
hmNetACDAddr The string value used to identify the management address component associated with the local system.	OctetString	.1.3.6.1.4.1.248.14.2.3.12.20.1.5
hmNetACDMAC The physical address of the device that was detected causing the ip address conflict.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.248.14.2.3.12.20.1.7
hmNetACDIfId The integer value used to identify the interface number on the local system where the ip address conflict was detected.	SNMPv2-SMIInteger32 Enumerated Values: 1 enabled 2 disabled Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.14.2.3.12.20.1.9

This table contains variables for each PTP port of
the switch.

hmNetPTPPortEntry row .1.3.6.1.4.1.248.14.2.3.40.2.1

Entry for one port.

Indexes

No indexes recorded

Column	Syntax	OID
hmNetPTPPortID Index to identify a port of the switch unit. This value is never greater than hmSysGroupCapacity.	Integer32 Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.248.14.2.3.40.2.1.1
hmNetPTPPortState State of the PTP port intance.	Enumeration Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.248.14.2.3.40.2.1.2
hmNetPTPPortBurstEnable Controls the burst enable flag.	Enumerationr/w	.1.3.6.1.4.1.248.14.2.3.40.2.1.3
hmNetPTPPortEnable The respective PTP Port of the Boundary Clock can be set to true (enabled) or set to false (disabled). If the port is disabled no PTP packets will be processed for the respective port.	Enumerationr/w	.1.3.6.1.4.1.248.14.2.3.40.2.1.4

This table contains variables for each PTP2 port of
the switch.

hmNetPTP2PortEntry row .1.3.6.1.4.1.248.14.2.3.41.2.1

Entry for one port.

Indexes

No indexes recorded

Column	Syntax	OID
hmNetPTP2PortEnable	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.248.14.2.3.41.2.1.1
hmNetPTP2PortState State of the PTP2 port intance.	Enumeration	.1.3.6.1.4.1.248.14.2.3.41.2.1.2
hmNetPTP2LogDelayReqInterval	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.14.2.3.41.2.1.3
hmNetPTP2PeerMeanPathDelay	PTPTimeInterval Type Constraints: range: 8	.1.3.6.1.4.1.248.14.2.3.41.2.1.4
hmNetPTP2LogAnnounceInterval	Enumerationr/w Constraints: range: 1-7	.1.3.6.1.4.1.248.14.2.3.41.2.1.5
hmNetPTP2AnnounceReceiptTimeout	Integer32r/w	.1.3.6.1.4.1.248.14.2.3.41.2.1.6
hmNetPTP2LogSyncInterval	Enumerationr/w	.1.3.6.1.4.1.248.14.2.3.41.2.1.7
hmNetPTP2DelayMechanism	Enumerationr/w	.1.3.6.1.4.1.248.14.2.3.41.2.1.8
hmNetPTP2LogPdelayReqInterval	Enumerationr/w Constraints: range: 1-8	.1.3.6.1.4.1.248.14.2.3.41.2.1.9
hmNetPTP2VersionNumber	Enumerationr/w Constraints: range: 0-16	.1.3.6.1.4.1.248.14.2.3.41.2.1.10
hmNetPTP2NetworkProtocol	Enumerationr/w Enumerated Values: 1 perm-ro 2 perm-rw	.1.3.6.1.4.1.248.14.2.3.41.2.1.11
hmNetPTP2V1Compatibility	Enumerationr/w Enumerated Values: 1 enable 2 disable 3 delete 4 invalid	.1.3.6.1.4.1.248.14.2.3.41.2.1.12
hmNetPTP2DelayAsymmetry	PTPTimeIntervalr/w Type Constraints: range: 8	.1.3.6.1.4.1.248.14.2.3.41.2.1.13
hmNetPTP2PortCapability This object shows the capability of the ptp port.	Bits	.1.3.6.1.4.1.248.14.2.3.41.2.1.14
hmNetPTP2VlanID VLAN in which PTP packets are send. With a value of -1 all packets are send untagged	Integer32r/w Constraints: range: 1-8	.1.3.6.1.4.1.248.14.2.3.41.2.1.15
hmNetPTP2VlanPriority VLAN priority of tagged ptp packets	Integer32r/w Constraints: range: 0-16	.1.3.6.1.4.1.248.14.2.3.41.2.1.16

This table contains variables for each PTP2 TC port of
the switch.

hmNetPTP2TCPortEntry row .1.3.6.1.4.1.248.14.2.3.42.2.1

Entry for one port.

Indexes

No indexes recorded

Column	Syntax	OID
hmNetPTP2TCPortEnable	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.248.14.2.3.42.2.1.1
hmNetPTP2TCLogPdelayReqInterval	Enumerationr/w Enumerated Values: 1 enable 2 disable 3 delete 4 invalid	.1.3.6.1.4.1.248.14.2.3.42.2.1.2
hmNetPTP2TCFaulty	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.248.14.2.3.42.2.1.3
hmNetPTP2TCPeerMeanPathDelay	PTPTimeInterval Type Constraints: range: 8	.1.3.6.1.4.1.248.14.2.3.42.2.1.4
hmNetPTP2TCDelayAsymmetry	PTPTimeIntervalr/w Constraints: range: 1-8	.1.3.6.1.4.1.248.14.2.3.42.2.1.5

A list of Management Access Entries (Rules) to increase security

hmRMAEntry row .1.3.6.1.4.1.248.14.2.3.70.2.1

An entry contains a rule for the Management Access.

Indexes

No indexes recorded

Column	Syntax	OID
hmRMAIndex The unique index used for each row in the RMA Table	Integer32 Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.248.14.2.3.70.2.1.1
hmRMARowStatus Describes the status of a row in this table if it is active or not available ...	SNMPv2-TCRowStatusr/w Enumerated Values: 1 enable 2 disable Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.248.14.2.3.70.2.1.2
hmRMAIpAddr Allowed IP address	SNMPv2-SMIIpAddressr/w Enumerated Values: 1 enable 2 disable Type Constraints: range: 4	.1.3.6.1.4.1.248.14.2.3.70.2.1.3
hmRMANetMask Network Mask	SNMPv2-SMIIpAddressr/w Enumerated Values: 1 enable 2 disable Type Constraints: range: 4	.1.3.6.1.4.1.248.14.2.3.70.2.1.4
hmRMASrvHttp Enables/disables HTTP access	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.248.14.2.3.70.2.1.5
hmRMASrvSnmp Enables/disbales SNMP access	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.248.14.2.3.70.2.1.6
hmRMASrvTelnet Enables/disables Telnet access	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.248.14.2.3.70.2.1.7
hmRMASrvSsh Enables/disables SSH access	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.248.14.2.3.70.2.1.8
hmRMASrvHttps Enables/disables HTTPS access	Enumerationr/w Enumerated Values: 1 enable 2 disable 3 delete 4 invalid	.1.3.6.1.4.1.248.14.2.3.70.2.1.9

a directory of the internal file system

hmFSFileEntry row .1.3.6.1.4.1.248.14.2.4.100.1

The entry of the hmFSFileTable.

Indexes

hmTrapDestIndex

Column	Syntax	OID
hmFSFileID This index is used to identify the associated file	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.248.14.2.4.100.1.1
hmFSFileName file name excluding path	SNMPv2-TCDisplayString Constraints: range: 0-16 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.14.2.4.100.1.2
hmFSFileSize file size in bytes	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.14.2.4.100.1.3
hmFSFileDate date in UNIX format (seconds since 1 jan 1970)	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.248.14.2.4.100.1.4

A list of the neighbour agents in a chassis

hmNeighbourAgentEntry row .1.3.6.1.4.1.248.14.2.6.1

The entry of the hmNeighbourAgentTable.

Indexes

No indexes recorded

Column	Syntax	OID
hmNeighbourSlot An index that uniquely identifies an agent by the slot in the chassis.	Integer32	.1.3.6.1.4.1.248.14.2.6.1.1
hmNeighbourIpAddress The IP Address of the agent.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.248.14.2.6.1.2

A list of valid SNMP Community Entries.

hmAuthCommEntry row .1.3.6.1.4.1.248.14.2.7.3.1

A list of SNMP Community properties.

Indexes

No indexes recorded

Column	Syntax	OID
hmAuthCommIndex An index that uniquely identifies an ordered entry in the SNMP Community Table.	Integer32	.1.3.6.1.4.1.248.14.2.7.3.1.1
hmAuthCommName The name of this SNMP Community Entry, e.g. public. This object can only be written.	OctetStringr/w	.1.3.6.1.4.1.248.14.2.7.3.1.2
hmAuthCommPerm The Read/Write (GET/SET) permission for the community. A (1) indicates perm-ro (GET) permission. A (2) indicates perm-wr (GET/SET) permission.	Enumerationr/w Constraints: range: 0-4095	.1.3.6.1.4.1.248.14.2.7.3.1.3
hmAuthCommState The state of this community entry. Enable (1) defines an entry that is valid. Disable (2) defines an entry that is valid but not enabled. Delete (3) removes an entry from the table. Invalid (4) defines an entry that …	Enumerationr/w	.1.3.6.1.4.1.248.14.2.7.3.1.4

A list of valid SNMP Trusted Host Entries.

hmAuthHostEntry row .1.3.6.1.4.1.248.14.2.7.4.1

A list of SNMP Host properties.

Indexes

No indexes recorded

Column	Syntax	OID
hmAuthHostIndex An index that uniquely identifies an ordered entry in the SNMP Trusted Host Table.	Integer32	.1.3.6.1.4.1.248.14.2.7.4.1.1
hmAuthHostName The name of this SNMP Trusted Host Entry, e.g. host1.	OctetStringr/w Constraints: range: 0-4095	.1.3.6.1.4.1.248.14.2.7.4.1.2
hmAuthHostCommIndex The index of this SNMP Trusted Host Entry's community entry in the hmAuthCommTable.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.14.2.7.4.1.3
hmAuthHostIpAddress The IP Address for the host. This identified host has permission to access information in this device's MIB tables, providing the SNMP security toggle is on (see hmMiscSNMPSecurity).	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.248.14.2.7.4.1.4
hmAuthHostIpMask The Network Mask for the trusted Host entry.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.248.14.2.7.4.1.5
hmAuthHostState The state of this trusted host entry. Enable (1) defines an entry that is valid. Disable (2) defines an entry that is valid but not enabled. Delete (3) removes an entry from the table. Invalid (4) defines an entry that …	Enumerationr/w Constraints: range: 0-4095	.1.3.6.1.4.1.248.14.2.7.4.1.6

A list of valid SNMP Community Entries used for Traps.

hmTrapCommEntry row .1.3.6.1.4.1.248.14.2.8.3.1

A list of SNMP Trap Community properties.

Indexes

No indexes recorded

Column	Syntax	OID
hmTrapCommIndex An index that uniquely identifies an ordered entry in the SNMP Community Trap Table.	Integer32	.1.3.6.1.4.1.248.14.2.8.3.1.1
hmTrapCommCommIndex The communities entry index of this SNMP Trap Community Entry.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.14.2.8.3.1.2
hmTrapCommColdStart Enable (1) or Disable (2) the SNMP ColdStart Trap for this SNMP community.	Enumerationr/w	.1.3.6.1.4.1.248.14.2.8.3.1.3
hmTrapCommLinkDown Enable (1) or Disable (2) the SNMP Link Down traps for this SNMP community.	Enumerationr/w Constraints: range: 1-5	.1.3.6.1.4.1.248.14.2.8.3.1.4
hmTrapCommLinkUp Enable (1) or Disable (2) the SNMP Link Up traps for this SNMP community.	Enumerationr/w Constraints: range: 1-128	.1.3.6.1.4.1.248.14.2.8.3.1.5
hmTrapCommAuthentication Enable (1) or Disable (2) the SNMP Authentication traps for this SNMP community.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.248.14.2.8.3.1.6
hmTrapCommBridge Enable (1) or Disable (2) the SNMP Bridge MIB traps for this SNMP community. Available Traps: newRoot (MACH) topologyChange (MACH)	Enumerationr/w Enumerated Values: 1 forward 2 discard	.1.3.6.1.4.1.248.14.2.8.3.1.7
hmTrapCommRMON Enable (1) or Disable (2) the SNMP RMON traps for this SNMP community. Available Traps: risingAlarm (MACH, MICE, RS2) fallingAlarm (MACH, MICE, RS2)	Enumerationr/w	.1.3.6.1.4.1.248.14.2.8.3.1.8
hmTrapCommUsergroup Enable (1) or Disable (2) the SNMP Enterprise usergroup traps for this SNMP community. Available Traps: hmNewUserTrap (MACH) hmPortSecurityTrap (MACH, MICE, RS2) hmPortSecConfigErrorTrap (MACH)	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.248.14.2.8.3.1.9
hmTrapCommDualHoming Enable (1) or Disable (2) the SNMP Enterprise dual homing traps for this SNMP community. Available Traps: hmDuHmReconfig (MACH) hmDuHmRedundancy (MACH) hmRingRedReconfig (MACH, MICE)	Enumerationr/w Enumerated Values: 1 disable 2 relay 3 server	.1.3.6.1.4.1.248.14.2.8.3.1.10
hmTrapCommChassis Enable (1) or Disable (2) the SNMP Enterprise chassis traps for this SNMP community. Available Traps: hmGroupMapChange (MACH) hmPowerSupply (MACH, MICE, RS2) hmFan (MACH) hmSignallingRelay (MICE, RS2) hmStandby (…	Enumerationr/w	.1.3.6.1.4.1.248.14.2.8.3.1.11
hmTrapCommState The state of this community entry. Enable (1) defines an entry that is valid. Disable (2) defines an entry that is valid but not enabled. Delete (3) removes an entry from the table. Invalid (4) defines an entry that i…	Enumerationr/w	.1.3.6.1.4.1.248.14.2.8.3.1.12

A list of valid SNMP Trap Trusted Host Destination entries.

hmTrapDestEntry row .1.3.6.1.4.1.248.14.2.8.4.1

A list of SNMP Trap Trusted Host Destination properties.

Indexes

No indexes recorded

Column	Syntax	OID
hmTrapDestIndex An index that uniquely identifies an ordered entry in the SNMP Trusted Host Destination Table.	Integer32	.1.3.6.1.4.1.248.14.2.8.4.1.1
hmTrapDestName The name of this SNMP Trusted Host Destination Entry, e.g. Admin.	OctetStringr/w	.1.3.6.1.4.1.248.14.2.8.4.1.2
hmTrapDestCommIndex The communities entry index of this SNMP Trusted Host Destination Entry's community.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.14.2.8.4.1.3
hmTrapDestIpAddress The IP Address for the host. This identified host has permission to access information in this device's MIB tables, providing the SNMP security toggle is on (see hmMiscSNMPSecurity).	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.248.14.2.8.4.1.4
hmTrapDestIpMaskobsolete The Network Mask for the trusted Host Destination entry.	SNMPv2-SMIIpAddressr/w Constraints: range: 1-2	.1.3.6.1.4.1.248.14.2.8.4.1.5
hmTrapDestState The state of this trusted trap destination entry. Enable (1) defines an entry that is valid. Disable (2) defines an entry that is valid but not enabled. Delete (3) removes an entry from the table. Invalid (4) defines …	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.248.14.2.8.4.1.6

A table displaying the IGMP Router Query PDU ports.

hmIGMPSnoopQueryEntry row .1.3.6.1.4.1.248.14.2.10.1.2.10.1

A table displaying the IGMP Router Query PDU ports.
These are maintained on a per VLAN basis.

Indexes

No indexes recorded

Column	Syntax	OID
hmIGMPSnoopQueryVlanIndex This is the VLAN index for which this entry is valid. If the switch only supports shared vlan learning (SVL), the value is always 1 and there is only 1 instance in the table.	Integer32 Enumerated Values: 1 manual 2 monitor 3 devicestate	.1.3.6.1.4.1.248.14.2.10.1.2.10.1.1
hmIGMPSnoopQueryPorts This read-only object displays the set of ports that have received IGMP Router Query PDUs for this VLAN as determined by the IGMP Snooping task.	OctetString Enumerated Values: 1 close 2 open	.1.3.6.1.4.1.248.14.2.10.1.2.10.1.2

A table containing the multicast filtering information
on a per vlan basis learned with IGMP Snooping.

hmIGMPSnoopFilterEntry row .1.3.6.1.4.1.248.14.2.10.1.2.11.1

The entry of the hmIGMPSnoopFilterTable.

Indexes

No indexes recorded

Column	Syntax	OID
hmIGMPSnoopFilterVlanIndex This is the VLAN index for which this entry is valid. If the switch only supports shared vlan learning (SVL), the value is always 1 and there is only 1 instance in the table.	Integer32 Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.248.14.2.10.1.2.11.1.1
hmIGMPSnoopFilterAddress The multicast destination MAC address in a frame to which this entry's filtering information applies.	SNMPv2-TCMacAddress Enumerated Values: 1 enable 2 disable Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.248.14.2.10.1.2.11.1.2
hmIGMPSnoopFilterLearntPorts The set of ports, to which frames destined for this Group MAC Address learned by IGMP Snooping are currently being forwarded. Each octet within the value of this object specifies a set of eight ports, with the first oct…	OctetString Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.248.14.2.10.1.2.11.1.3

A table containing forwarding information for each
VLAN, specifying the set of ports to which forwarding of
all multicasts applies, configured statically by
management.
An entry appears in this table for all VLANs that are currently
instantiated.

hmIGMPSnoopForwardAllEntry row .1.3.6.1.4.1.248.14.2.10.1.2.12.1

Forwarding information for a VLAN, specifying the set
of ports to which all multicasts should be forwarded,
configured statically by management.

Indexes

No indexes recorded

Column	Syntax	OID
hmIGMPSnoopForwardAllVlanIndex This is the VLAN index for which this entry is valid. If the switch only supports shared vlan learning (SVL), the value is always 1 and there is only 1 instance in the table.	Integer32 Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.248.14.2.10.1.2.12.1.1
hmIGMPSnoopForwardAllStaticPorts The set of ports configured by management in this VLAN to which all multicast group-addressed frames learned by IGMP are to be forwarded. This value will be restored after the device is reset.	OctetStringr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.248.14.2.10.1.2.12.1.2

A table displaying the IGMP Static Query ports.

hmIGMPSnoopQueryStaticEntry row .1.3.6.1.4.1.248.14.2.10.1.2.13.1

The entry of the hmIGMPSnoopQueryStaticTable.

Indexes

No indexes recorded

Column	Syntax	OID
hmIGMPSnoopQueryStaticVlanIndex This is the VLAN index for which this entry is valid. If the switch only supports shared vlan learning (SVL), the value is always 1 and there is only 1 instance in the table.	Integer32 Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.248.14.2.10.1.2.13.1.1
hmIGMPSnoopQueryStaticPorts The set of ports explicitly configured by management to be IGMP-forwarding ports.	OctetStringr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.248.14.2.10.1.2.13.1.2
hmIGMPSnoopQueryStaticAutomaticPorts The set of ports that are automatically learned by LLDP protocol to be IGMP-forwarding ports.	OctetString Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.248.14.2.10.1.2.13.1.3
hmIGMPSnoopQueryStaticAutomaticPortsEnable The set of ports that are allowed to be learned automatically by LLDP protocol to be IGMP-forwarding ports.	OctetStringr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.248.14.2.10.1.2.13.1.4

This table contains variables for each interface of
the switch.

hmRelayInterfaceEntry row .1.3.6.1.4.1.248.14.2.11.11.1

The entry of the hmRelayInterfaceTable.

Indexes

No indexes recorded

Column	Syntax	OID
hmRelayIfaceGroupID index to identify an interface card. This value is never greater than hmSysGroupCapacity.	Integer32 Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.248.14.2.11.11.1.1
hmRelayIfaceID index to identify an interface within an interface card.	Integer32	.1.3.6.1.4.1.248.14.2.11.11.1.2
hmRelayIfaceOption82Enable Enable or disable DHCP Option 82 on this physical port.	Enumerationr/w	.1.3.6.1.4.1.248.14.2.11.11.1.3
hmRelayIfaceBCRequestFwd Enable or disable relaying of incoming broadcasted BOOTP/DHCP request packets on this physical port. Hirschmann Multicast BOOTP/DHCP requests will always be relayed.	Enumerationr/w Constraints: range: 1-128	.1.3.6.1.4.1.248.14.2.11.11.1.4
hmRelayIfaceCircuitID Contains the actual Circuit ID sub option for this interface of the relay agent. It is a best guess value, since some information is not known before the actual reception of a BOOTP/DHCP request message.	OctetString Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.248.14.2.11.11.1.5
hmRelayIfaceDhcpRelayAdminState Enable or disable DHCP Relay Agent on this physical port.	Enumerationr/w	.1.3.6.1.4.1.248.14.2.11.11.1.6
hmRelayIfaceDhcpRelayOperState Current active DHCP protocol on this physical port.	Enumeration	.1.3.6.1.4.1.248.14.2.11.11.1.7

This table contains objects to configure
DHCP Servers.

hmRelayServerAddrEntry row .1.3.6.1.4.1.248.14.2.11.12.1

The DHCP Server objects.

Indexes

No indexes recorded

Column	Syntax	OID
hmRelayServerAddrIndex Index for server table.	Integer32 Enumerated Values: 1 other 2 linkFailure 3 controlLine 4 redNotGuaranteed 5 psState 6 temperature 7 moduleRemoval 8 acaRemoval 9 fanFailure 10 acaNotInSync 11 sRedNotGuaranteed	.1.3.6.1.4.1.248.14.2.11.12.1.1
hmRelayServerAddr The address of the external DHCP server.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.248.14.2.11.12.1.2
hmRelayServerInterface If an Interface is set, only DHCP packets from this interface are relayed to the server.	IF-MIBInterfaceIndexOrZeror/w Enumerated Values: 1 error 2 noerror Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.248.14.2.11.12.1.3
hmRelayServerRowStatus Indicates the status of an entry in this table, and is used to create/delete entries. Objects within this table can by changed while the status is 'active'.	SNMPv2-TCRowStatusr/w Enumerated Values: 1 error 2 ignore Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.248.14.2.11.12.1.4

This table contains all variables to configure the behaviour
of the signalling contacts.

hmSigConConfigEntry row .1.3.6.1.4.1.248.14.2.12.1.1

The entry of the hmSigConConfigTable.

Indexes

No indexes recorded

Column	Syntax	OID
hmSigConID This index is used to identify the associated signalling contact.	Integer32 Enumerated Values: 1 error 2 ignore	.1.3.6.1.4.1.248.14.2.12.1.1.1
hmSigConTrapEnable Determines wether a trap shall be sent or not, when the signal contact operating state changes.	Enumerationr/w Enumerated Values: 1 error 2 ignore	.1.3.6.1.4.1.248.14.2.12.1.1.2
hmSigConTrapCause This object identifies the cause for a trap. The index of the entity which produces the trap is specified by hmSigConTrapCauseIndex.	Enumeration Enumerated Values: 1 error 2 ignore	.1.3.6.1.4.1.248.14.2.12.1.1.3
hmSigConTrapCauseIndex This attribute specifies the entity which produces the trap. 1 - n: index of powersupply table / interfaces table 0: other errors	SNMPv2-SMIInteger32 Enumerated Values: 1 error 2 ignore Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.14.2.12.1.1.4
hmSigConMode This attribute specifies the behaviour of the relay contact. The factory settings for signal contact 1 is monitoring the correct operation of entries specified to be survied. When the device has also a second signal con…	Enumerationr/w Enumerated Values: 1 error 2 ignore	.1.3.6.1.4.1.248.14.2.12.1.1.5
hmSigConManualActivate When operating in manual mode, the signal contact state can be set by this attribute.	Enumerationr/w Enumerated Values: 1 error 2 ignore	.1.3.6.1.4.1.248.14.2.12.1.1.6
hmSigConOperState This attribute shows the current operating state of the signal contact.	Enumeration Enumerated Values: 1 error 2 ignore	.1.3.6.1.4.1.248.14.2.12.1.1.7
hmSigConSenseLinkFailure Sets the monitoring of the network connection(s).	Enumerationr/w Enumerated Values: 1 error 2 ignore	.1.3.6.1.4.1.248.14.2.12.1.1.8
hmSigConSenseControlLine Sets the monitoring of the ring/network coupling.	Enumerationr/w Enumerated Values: 1 error 2 ignore	.1.3.6.1.4.1.248.14.2.12.1.1.9
hmSigConSenseRedNotGuaranteed Sets the monitoring of the HIPER-Ring, MRP-Ring or Fast HIPER-Ring.	Enumerationr/w Enumerated Values: 1 error 2 ignore	.1.3.6.1.4.1.248.14.2.12.1.1.10
hmSigConSensePS1State Sets the monitoring of the power supply 1.	Enumerationr/w Enumerated Values: 1 error 2 ignore	.1.3.6.1.4.1.248.14.2.12.1.1.11
hmSigConSensePS2State Sets the monitoring of the power supply 2.	Enumerationr/w Enumerated Values: 1 error 2 ignore	.1.3.6.1.4.1.248.14.2.12.1.1.12
hmSigConSenseTemperature Sets the monitoring of the device temperature.	Enumerationr/w Enumerated Values: 1 error 2 ignore	.1.3.6.1.4.1.248.14.2.12.1.1.13
hmSigConSenseModuleRemoval Sets the monitoring of module removal (platform dependant).	Enumerationr/w Enumerated Values: 1 error 2 ignore	.1.3.6.1.4.1.248.14.2.12.1.1.14
hmSigConSenseACARemoval Sets the monitoring of the auto configuration adapter removal.	Enumerationr/w	.1.3.6.1.4.1.248.14.2.12.1.1.15
hmSigConSensePS3State Sets the monitoring of the power supply 3 (platform dependant).	Enumerationr/w	.1.3.6.1.4.1.248.14.2.12.1.1.16
hmSigConSensePS4State Sets the monitoring of the power supply 4 (platform dependant).	Enumerationr/w Constraints: range: 0-9	.1.3.6.1.4.1.248.14.2.12.1.1.17
hmSigConSenseFan1State Sets the monitoring of the cooling fan (platform dependant).	Enumerationr/w Constraints: range: 1-32	.1.3.6.1.4.1.248.14.2.12.1.1.18
hmSigConSensePS5State Sets the monitoring of the power supply 5 (platform dependant).	Enumerationr/w	.1.3.6.1.4.1.248.14.2.12.1.1.19
hmSigConSensePS6State Sets the monitoring of the power supply 6 (platform dependant).	Enumerationr/w	.1.3.6.1.4.1.248.14.2.12.1.1.20
hmSigConSensePS7State Sets the monitoring of the power supply 7 (platform dependant).	Enumerationr/w Enumerated Values: 1 readOnly 2 readWrite	.1.3.6.1.4.1.248.14.2.12.1.1.21
hmSigConSensePS8State Sets the monitoring of the power supply 8 (platform dependant).	Enumerationr/w Enumerated Values: 1 active 2 notInService 3 config 4 destroy	.1.3.6.1.4.1.248.14.2.12.1.1.22
hmSigConSenseACANotInSync Sets the monitoring whether the configuration on ACA is in sync with the configuration in NVRAM.	Enumerationr/w	.1.3.6.1.4.1.248.14.2.12.1.1.23
hmSigConSenseSRedNotGuaranteed Sets the monitoring of sub-rings if configured and activated on the device.	Enumerationr/w	.1.3.6.1.4.1.248.14.2.12.1.1.24

This table contains all variables to mask an alarm for the
signalling relay, produced by a link. The index for a link
corresponds with ifMauIfIndex. The table is also used
for the device monitoring configuration.

hmSigConLinkEntry row .1.3.6.1.4.1.248.14.2.12.2.1

The entry of the hmSigConLinkTable.

Indexes

No indexes recorded

Column	Syntax	OID
hmSigConLinkID This index is used to identify the associated link and corresponds with ifMauIfIndex.	Integer32	.1.3.6.1.4.1.248.14.2.12.2.1.1
hmSigConLinkAlarm Indicates whether an alarm for the signalling relay of the associated link will be produced or not, so you can mask the value of ifMauMediaAvailable.	Enumerationr/w Enumerated Values: 1 active 2 notInService 3 config 4 destroy	.1.3.6.1.4.1.248.14.2.12.2.1.2

This table contains all variables to configure the behaviour
of the device state.

hmDevMonConfigEntry row .1.3.6.1.4.1.248.14.2.12.3.1

Configuration of the device monitoring.

Indexes

hmPOEPortIndex

Column	Syntax	OID
hmDevMonID This index is used to identify the associated device status (currently only one).	Integer32 Constraints: range: 1-128	.1.3.6.1.4.1.248.14.2.12.3.1.1
hmDevMonTrapEnable Determines wether a trap shall be sent or not, when the device monitoring state changes.	Enumerationr/w	.1.3.6.1.4.1.248.14.2.12.3.1.2
hmDevMonTrapCause This object identifies the cause for a trap. The index of the entity which produces the trap is specified by hmDevMonTrapCauseIndex.	Enumeration	.1.3.6.1.4.1.248.14.2.12.3.1.3
hmDevMonTrapCauseIndex This attribute specifies the entity which produces the trap. 1 - n: index of powersupply table / interfaces table 0: other errors	SNMPv2-SMIInteger32 Constraints: range: 0-30000	.1.3.6.1.4.1.248.14.2.12.3.1.4
hmDevMonSwitchState This attribute shows the current state of the device monitoring.	Enumeration	.1.3.6.1.4.1.248.14.2.12.3.1.5
hmDevMonSenseLinkFailure Sets the monitoring of the network connection(s).	Enumerationr/w	.1.3.6.1.4.1.248.14.2.12.3.1.6
hmDevMonSenseControlLine Sets the monitoring of the ring/network coupling.	Enumerationr/w Constraints: range: 1-128	.1.3.6.1.4.1.248.14.2.12.3.1.7
hmDevMonSenseRedNotGuaranteed Sets the monitoring of the HIPER-Ring, MRP-Ring or Fast HIPER-Ring.	Enumerationr/w Constraints: range: 0-1000	.1.3.6.1.4.1.248.14.2.12.3.1.8
hmDevMonSensePS1State Sets the monitoring of the power supply 1.	Enumerationr/w Constraints: range: 0-1000	.1.3.6.1.4.1.248.14.2.12.3.1.9
hmDevMonSensePS2State Sets the monitoring of the power supply 2.	Enumerationr/w	.1.3.6.1.4.1.248.14.2.12.3.1.10
hmDevMonSenseTemperature Sets the monitoring of the device temperature.	Enumerationr/w	.1.3.6.1.4.1.248.14.2.12.3.1.11
hmDevMonSenseModuleRemoval Sets the monitoring of module removal (platform dependant).	Enumerationr/w Constraints: range: 1-99	.1.3.6.1.4.1.248.14.2.12.3.1.12
hmDevMonSenseACARemoval Sets the monitoring of the auto configuration adapter removal.	Enumerationr/w	.1.3.6.1.4.1.248.14.2.12.3.1.13
hmDevMonSensePS3State Sets the monitoring of the power supply 3 (platform dependant).	Enumerationr/w	.1.3.6.1.4.1.248.14.2.12.3.1.14
hmDevMonSensePS4State Sets the monitoring of the power supply 4 (platform dependant).	Enumerationr/w	.1.3.6.1.4.1.248.14.2.12.3.1.15
hmDevMonSenseFan1State Sets the monitoring of the cooling fan (platform dependant).	Enumerationr/w Constraints: range: 1-128	.1.3.6.1.4.1.248.14.2.12.3.1.16
hmDevMonSensePS5State Sets the monitoring of the power supply 5 (platform dependant).	Enumerationr/w Enumerated Values: 0 none 1 ingress 2 egress 3 both	.1.3.6.1.4.1.248.14.2.12.3.1.17
hmDevMonSensePS6State Sets the monitoring of the power supply 6 (platform dependant).	Enumerationr/w	.1.3.6.1.4.1.248.14.2.12.3.1.18
hmDevMonSensePS7State Sets the monitoring of the power supply 7 (platform dependant).	Enumerationr/w	.1.3.6.1.4.1.248.14.2.12.3.1.19
hmDevMonSensePS8State Sets the monitoring of the power supply 8 (platform dependant).	Enumerationr/w	.1.3.6.1.4.1.248.14.2.12.3.1.20
hmDevMonSenseACANotInSync Sets the monitoring whether the configuration on ACA is in sync with the configuration in NVRAM.	Enumerationr/w	.1.3.6.1.4.1.248.14.2.12.3.1.21
hmDevMonSenseSRedNotGuaranteed Sets the monitoring of sub-rings if configured and activated on the device.	Enumerationr/w Enumerated Values: 1 port-disable 2 trap-only 3 auto-disable	.1.3.6.1.4.1.248.14.2.12.3.1.22