hmIfaceCableCrossing
HMPRIV-MGMT-SNMP-MIB ·
.1.3.6.1.4.1.248.14.1.1.11.1.27
Object
column
r/w
Enumeration
This variable configures the cable crossing on twisted pair cables. When set to 'enable', the port uses the crossover mode. When set to 'disable', the port does not use the crossover mode. 'Unsupported' is shown, if a port does not support cable crossing. It is not possible to set 'unsupported' to any type of port.
Context
- MIB
- HMPRIV-MGMT-SNMP-MIB
- OID
.1.3.6.1.4.1.248.14.1.1.11.1.27- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- hmInterfaceEntry
- Table
- hmInterfaceTable
- Siblings
- 28
Syntax
Enumeration
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hmIfaceGroupID index to identify an interface card. This value is never
greater than hmSysGroupCapacity. | column | Integer32 | .1.3.6.1.4.1.248.14.1.1.11.1.1 |
| hmIfaceTrunkID If the value of this variable is greater 0 then it belongs
to the link aggregation instance with the same index. If
the value is 0 no link aggregation uses this interface. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.248.14.1.1.11.1.10 |
| hmIfacePrioTOSEnable Enable or disable Priority setting from IP TOS field. | column | Enumeration | .1.3.6.1.4.1.248.14.1.1.11.1.11 |
| hmIfaceBcastLimit Broadcast rate: maximum number of broadcasts to be sent
on this port within one second, use 0 for no limitation. | column | Integer32 | .1.3.6.1.4.1.248.14.1.1.11.1.12 |
| hmIfaceUtilization The best estimate of the mean physical layer
network utilization on this interface during the
last sampling interval, in hundredths of a percent.
The first historyControlInterval… | column | Integer32 | .1.3.6.1.4.1.248.14.1.1.11.1.13 |
| hmIfaceUtilizationControlInterval The interval in seconds over which the data is
sampled for hmIfaceUtilization.
This interval can be any number of seconds
between 1 and 3600 (1 hour).
The first historyControlInte… | column | Integer32 | .1.3.6.1.4.1.248.14.1.1.11.1.14 |
| hmIfaceStpBpduGuardEnable Enabled or disabled the BPDU guard functionality per port.
If BPDU guard functionality are global enabled (hmSysStpBPDUGuardEnable=enable(1)),
and BPDU guard are enabled per port … | column | Enumeration | .1.3.6.1.4.1.248.14.1.1.11.1.15 |
| hmIfaceStpBpduGuardStatus Advertised the state of BPDU guard functionality for this port.
If BPDU guard functionality fot this port is disabled or guard
functionality is enabled, but no BPDUs are received… | column | Enumeration | .1.3.6.1.4.1.248.14.1.1.11.1.16 |
| hmIfaceCapability Capability of the interface coded as an integer value
with each bit representing a special capability.
Meaning of the bits:
Bit 0: cabletest capability
Bit 1: realt… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.248.14.1.1.11.1.17 |
| hmIfaceIngressLimiterMode The ingress limiter can work in different modes.
Mode all limits the complete ingress traffic.
Mode bc limits only the ingress broadcast traffic.
Mode bc_mc limits the ingress bro… | column | Enumeration | .1.3.6.1.4.1.248.14.1.1.11.1.18 |
| hmIfaceIngressLimiterCalculationMode The ingress limiter can measure the traffic
on a bytes per second
or on a packets per second basis.
The limiter calculation mode is hardware dependend.
Not all modes are availabl… | column | Enumeration | .1.3.6.1.4.1.248.14.1.1.11.1.19 |
| hmIfaceID index to identify an interface within an interface card. | column | Integer32 | .1.3.6.1.4.1.248.14.1.1.11.1.2 |
| hmIfaceIngressLimiterRate The rate of the ingress limiter.
The value 0 disables the limiter. | column | Integer32 | .1.3.6.1.4.1.248.14.1.1.11.1.20 |
| hmIfaceEgressLimiterMode The egress limiter can work in different modes.
Mode all limits the complete egress traffic.
Mode bc limits only the egress broadcast traffic.
Mode bc_mc limits the egress broadca… | column | Enumeration | .1.3.6.1.4.1.248.14.1.1.11.1.21 |
| hmIfaceEgressLimiterCalculationMode The egress limiter can measure the traffic
on a bytes per second
or on a packets per second basis.
The limiter calculation mode is hardware dependend.
Not all modes are available… | column | Enumeration | .1.3.6.1.4.1.248.14.1.1.11.1.22 |
| hmIfaceEgressLimiterRate The rate of the egress limiter.
The value 0 disables the limiter. | column | Integer32 | .1.3.6.1.4.1.248.14.1.1.11.1.23 |
| hmIfaceUtilizationAlarmUpperThreshold Surveys the interface utilization hmIfaceUtilization and
generates an alarm for this interfaces, if the given
limit is exceeded.
A value of 0 disables the alarm generation. | column | Integer32 | .1.3.6.1.4.1.248.14.1.1.11.1.24 |
| hmIfaceUtilizationAlarmLowerThreshold Surveys the interface utilization hmInfaceUtilization and
removes the alarm condition for this interfaces, if
the utilization value is below the given limit.
A value of 0 disabl… | column | Integer32 | .1.3.6.1.4.1.248.14.1.1.11.1.25 |
| hmIfaceUtilizationAlarmCondition The alarm condition is given (true), if the given
hmIfaceUtilizationAlarmUpperThreshold limit is exceeded
by the interface utilization. The alarm condition
will be removed, when … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.248.14.1.1.11.1.26 |
| hmIfacePhyFastLinkDetection This variable configures the PHY specific
fast link detection feature on this port.
'Unsupported' is shown, if a port does not
support this feature.
It is not possible to set 'uns… | column | Enumeration | .1.3.6.1.4.1.248.14.1.1.11.1.28 |
| hmIfaceAcceptableFrameTypes obsolete This object is 'obsolete' and is replaced by hmIfaceExtAcceptableFrameTypes.
When this is admitOnlyVlanTagged(2) the device will
discard untagged frames received on this port.
Wh… | column | Enumeration | .1.3.6.1.4.1.248.14.1.1.11.1.29 |
| hmIfaceStpEnable Enable or disable spanning tree protocol. | column | Enumeration | .1.3.6.1.4.1.248.14.1.1.11.1.3 |
| hmIfaceLinkType Describes the link type of the interface. | column | Enumeration | .1.3.6.1.4.1.248.14.1.1.11.1.4 |
| hmIfaceAction This object, when read, always returns a value of noAction(1).
When set to resetStats(2), a reset of all statistic counters
within this interfacecard will be forced. | column | Enumeration | .1.3.6.1.4.1.248.14.1.1.11.1.5 |
| hmIfaceNextHopMacAddress The macaddress of the next switch agent reachable via this
interface. If the value is 0:0:0:0:0:0, no other switch is
seen via this interface. | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.248.14.1.1.11.1.6 |
| hmIfaceFlowControl Enables or disables flow control per port | column | Enumeration | .1.3.6.1.4.1.248.14.1.1.11.1.7 |
| hmIfacePriorityThreshold This object is used to support the dot1dTrafficClassTable.
It defines the thresholds of the available priority-classes.
Starting at MACH Release 2.20 this variable is not used any… | column | Integer32 | .1.3.6.1.4.1.248.14.1.1.11.1.8 |
| hmIfaceName User configurable textual description of the interface. On devices
which support Power over Ethernet (IEEE 802.af), this object is
mapped to pethPsePortType of the RFC3621 MIB. | column | OctetString | .1.3.6.1.4.1.248.14.1.1.11.1.9 |