CISCO-PAGP-MIB Table View

The pagpEtherChannelTable specifies, per physical interface,
the Fast Etherchannel operational mode (off, manual, or
protocol-controlled) and the capability of the interface to form
aggregations.  Interfaces that do not support Fast Etherchannel
or PAgP do not have an entry in this table, nor do the
agports, themselves.

pagpEtherChannelEntry row .1.3.6.1.4.1.9.9.98.1.1.1.1

The entry describes the permitted interface aggregation.
Entries are created by the managed system for each interface
which supports Fast Etherchannel.

Indexes

IF-MIBifIndex

Column	Syntax	OID
pagpEthcOperationMode The managed device will refuse a request to set pagpEthcOperationMode to the pagpOn(3) state if the device does not implement the PAgP protocol. The managed device will refuse to set pagpEthcOperationMode to manual(2) …	PagpEthcOperationModer/w Type Values: 1 off 2 manual 3 pagpOn	.1.3.6.1.4.1.9.9.98.1.1.1.1.1
pagpDeviceId Uniquely identifies a device which implements Fast Etherchannel. The combination of pagpDeviceId and ifIndex must be unique over all interfaces in a network. pagpDeviceId typically identifies a device such as a bridge,…	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.9.9.98.1.1.1.1.2
pagpPhysGroupCapability The values in pagpPhysGroupCapability indicate the aggregation capability of the underlying hardware. The speed, configuration, and status condition of the interface, e.g. ISL protocol on/off, ifOperStatu…	PagpGroupCapability	.1.3.6.1.4.1.9.9.98.1.1.1.1.3
pagpOperGroupCapability This variable informs the system administrator examining the Fast Etherchannel MIB of the capabilities of the current state of the interface's hardware to form agports. The pagpOperGroupCapability values …	PagpGroupCapability	.1.3.6.1.4.1.9.9.98.1.1.1.1.4
pagpAdminGroupCapability pagpAdminGroupCapability is used by the network administrator to control the aggregation of interfaces into agports. The default value of pagpAdminGroupCapability is equal to the value of pagpPhysGroupCapability on tha…	PagpGroupCapabilityr/w	.1.3.6.1.4.1.9.9.98.1.1.1.1.5
pagpPortPriority The priority of this interface relative to other interfaces when determining which interface is to be used in Hot Standby mode. Among all interfaces aggregated together with a single agport, the one with …	PagpPortPriorityr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.98.1.1.1.1.6
pagpLearnMethod This interface's learning method value. Specifies whether this device is able to learn the location of a source MAC address based on the agport on which it was received, agPort(2), or on the interface on which it was r…	PagpLearnMethodr/w Type Values: 1 physPort 2 agPort 3 undefined	.1.3.6.1.4.1.9.9.98.1.1.1.1.7
pagpGroupIfIndex If pagpGroupIfIndex is 0, then the inteface is not aggregated to an agport, and is unavailable for normal data reception and transmission. If pagpGroupIfIndex equals the interface's own ifIndex, the inter…	CISCO-TCInterfaceIndexOrZero Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.9.9.98.1.1.1.1.8
pagpDistributionProtocol pagpDistributionProtocol controls the load balancing algorithms used on this interface's agport to distribute outgoing data frames among its component interfaces, such as IP address. Configuring pagpDistributionProtoco…	Enumerationr/w Enumerated Values: 1 ip 2 mac 3 port 4 vlanIpPort 5 vlanIp 6 ipPort	.1.3.6.1.4.1.9.9.98.1.1.1.1.9
pagpDistributionAddress pagpDistributionAddress controls the type of distribution on the configured pagpDistributionProtocol used on this interface's agport to distribute outgoing data frames among its component interfaces. For example if the…	Enumerationr/w Enumerated Values: 1 source 2 destination 3 both	.1.3.6.1.4.1.9.9.98.1.1.1.1.10
pagpRate Specifies the rate at which the PAgP packets are transmitted on this interface. fast(1) : PAgP packets are transmitted at the fast rate on this interface. normal(2) : PAgP packets are transmitted …	Enumerationr/w Enumerated Values: 1 fast 2 normal	.1.3.6.1.4.1.9.9.98.1.1.1.1.11
pagpInPacketTimeout Specifies the earliest time at which received PAgP information packets are timed out.	SecondsUnsigned32r/w Constraints: range: 1-4294967295	.1.3.6.1.4.1.9.9.98.1.1.1.1.12

The table of per-interface Port Aggregation Protocol variables.
Physical interfaces that support Fast Etherchannel and PAgP
protocol have an entry in this table.  If the value of
pagpEthcOperationMode for the corresponding interface is off(1)
or
manual(2), then the the interface does not have any entries in
this table.

pagpProtocolConfigEntry row .1.3.6.1.4.1.9.9.98.1.2.1.1

The entry describes the operational state of the PAgP protocol
on
a particular physical interface. Entries in this table are for
interfaces that support both Fast Etherchannel and PAgP
protocol.
The agport itself is no…

Indexes

IF-MIBifIndex

Column	Syntax	OID
pagpOperationMode Controls the operational mode of the PAgP protocol on this interface.	PagpOperationModer/w Type Values: 1 desirable 2 desirableSilent 3 automatic 4 automaticSilent	.1.3.6.1.4.1.9.9.98.1.2.1.1.1
pagpPortState The state of the PAgP state machine on this interface. Values: portDown(1) - interface's ifOperStatus is not Up; portUp(2) - interface's ifOperStatus is Up, no packets …	Enumeration Enumerated Values: 1 portDown 2 portUp 3 dataReceived 4 upData 5 pagpReceived 6 biDirectional 7 upPagp 8 upMult	.1.3.6.1.4.1.9.9.98.1.2.1.1.2
pagpLastStateChange Value of sysUpTime the last time that pagpPortState changed.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.9.9.98.1.2.1.1.3
pagpHelloFrequency If pagpHelloFrequency is slow(2), this device uses a 105 second timer on this interface to time out receipt of PAgP packet. If fast(1), this device uses a 3.5 second timer. PAgP uses fast(1) by default. This value is …	Enumeration Enumerated Values: 1 fast 2 slow	.1.3.6.1.4.1.9.9.98.1.2.1.1.4
pagpDistributionAlgorithm pagpDistributionAlgorithm describes, in human terms, the method used on this interface's agport to distribute outgoing data frames among its component interfaces. 'Source MAC address', 'Source and Destination MAC addre…	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.9.9.98.1.2.1.1.5
pagpPartnerCount The number of other devices known to be transmitting PAgP packets to this device on this physical interface. If pagpPartnerCount contains none(1), then the values of the remainder of the variables in this…	Enumeration Enumerated Values: 1 none 2 one 3 many	.1.3.6.1.4.1.9.9.98.1.2.1.1.6
pagpPartnerDeviceId MAC Address of the partner, obtained from the PAgP packet last received on this interface. Contains all 0 if pagpPartnerCount contains none(1).	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.9.9.98.1.2.1.1.7
pagpPartnerLearnMethod The value of the partner's pagpLearnMethod value, obtained from the PAgP packet last received on this interface. undefined(3) if pagpPartnerCount contains none(1).	PagpLearnMethod Type Values: 1 physPort 2 agPort 3 undefined	.1.3.6.1.4.1.9.9.98.1.2.1.1.8
pagpPartnerPortPriority The value of the partner's pagpPortPriority, obtained from the PAgP packet last received on this interface. 0 if pagpPartnerCount contains none(1).	PagpPortPriority Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.98.1.2.1.1.9
pagpPartnerIfIndex The value of the partner's ifIndex value, obtained from the PAgP packet last received on this interface. 0 if pagpPartnerCount contains none(1). Use CISCO-CDP-MIB cdpCacheTable to resolve the partner's I…	CISCO-TCInterfaceIndexOrZero Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.9.9.98.1.2.1.1.10
pagpPartnerGroupCapability The value of the partner's pagpOperGroupCapability obtained from the PAgP packet last received on this interface. 0 if pagpPartnerCount contains none(1)	PagpGroupCapability	.1.3.6.1.4.1.9.9.98.1.2.1.1.11
pagpPartnerGroupIfIndex The value of the partner's pagpGroupIfIndex obtained from the PAgP packet last received on this interface. 0 if pagpPartnerCount contains none(1).	CISCO-TCInterfaceIndexOrZero Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.9.9.98.1.2.1.1.12
pagpPartnerDeviceName The DisplayString obtained from the PAgP packet last received on this interface. 0-length string if pagpPartnerCount contains none(1), or if no device name has been received. The value transmitted in a P…	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.9.9.98.1.2.1.1.13
pagpPartnerPortName The DisplayString obtained from the PAgP packet last received on this interface. 0-length string if pagpPartnerCount contains none(1), or if no port name has been received. The value transmitted in a PAg…	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.9.9.98.1.2.1.1.14
pagpPartnerAgportMACAddress The MacAddress obtained from the PAgP packet last received on this interface. All 0 if pagpPartnerCount contains none(1) or if no agport MacAddress has been received in a PAgP packet. If this value is no…	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.9.9.98.1.2.1.1.15

The table of per-interface Port Aggregation Protocol
statistics.  The entries in this table are
present only on an interface that is capable both of
implementing
Fast Etherchannel, and can be controlled by the PAgP protocol.
The agport itself is not represented in this table.

pagpProtocolStatsEntry row .1.3.6.1.4.1.9.9.98.1.2.2.1

The entry describes the accumulated statistics of the PAgP
protocol operation on the aggregated interface.

Indexes

IF-MIBifIndex

Column	Syntax	OID
pagpInPackets Number of PAgP information packets received on this interface.	packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.98.1.2.2.1.3
pagpOutPackets Number of PAgP information packets transmitted on this interface.	packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.98.1.2.2.1.4
pagpInFlushes Number of PAgP flush packets received and echoed on this interface not matching any pagpDeviceId belonging to the managed device. This counts PAgP flush packets originated by another device, and indicates that the othe…	packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.98.1.2.2.1.5
pagpReturnedFlushes Number of PAgP flush packets received on this interface matching some pagpDeviceId belonging to this device. This counts PAgP flush packets which were originated by the managed device and returned to it by another devi…	packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.98.1.2.2.1.6
pagpOutFlushes Number of PAgP flush packets generated on this interface. Does not count flush packets counted in pagpInFlushes and returned to the sender. If pagpOutFlushes is counting and pagpReturnedFlushes is not, the other devic…	packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.98.1.2.2.1.7
pagpInErrors Number of packet received on this interface which were identified by the encapsulation as being PAgP packets (of any type, e.g. information or flush), but which were not valid packets because of length, version, number …	packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.98.1.2.2.1.8