pagpPortPriority
CISCO-PAGP-MIB ·
.1.3.6.1.4.1.9.9.98.1.1.1.1.6
Object
column
r/w
PagpPortPriority
The priority of this interface relative to other interfaces
when determining which interface is to be used in Hot
Standby mode.
Among all interfaces aggregated together with a single agport,
the one with the highest numerical value of pagpPortPriority is
selected for use. Default value is 128.
Context
- MIB
- CISCO-PAGP-MIB
- OID
.1.3.6.1.4.1.9.9.98.1.1.1.1.6- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- pagpEtherChannelEntry
- Table
- pagpEtherChannelTable
- Siblings
- 11
Syntax
PagpPortPriority
- Source
- PagpPortPriority
- Base type
Integer32
Values & Constraints
Type Constraints
range: 0..255
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| pagpEthcOperationMode The managed device will refuse a request to set
pagpEthcOperationMode to the pagpOn(3) state if the device does
not implement the PAgP protocol. The managed device will refuse
to… | column | PagpEthcOperationMode | .1.3.6.1.4.1.9.9.98.1.1.1.1.1 |
| pagpDistributionAddress pagpDistributionAddress controls the type of distribution
on the configured pagpDistributionProtocol used on this
interface's agport to distribute outgoing data frames among its
… | column | Enumeration | .1.3.6.1.4.1.9.9.98.1.1.1.1.10 |
| pagpRate Specifies the rate at which the PAgP packets are transmitted
on this interface.
fast(1) : PAgP packets are transmitted at the fast rate
on this interface.
norm… | column | Enumeration | .1.3.6.1.4.1.9.9.98.1.1.1.1.11 |
| pagpInPacketTimeout Specifies the earliest time at which received PAgP
information packets are timed out. | column | Seconds Unsigned32 | .1.3.6.1.4.1.9.9.98.1.1.1.1.12 |
| pagpDeviceId Uniquely identifies a device which implements Fast
Etherchannel.
The combination of pagpDeviceId and ifIndex must be unique over
all interfaces in a network. pagpDeviceId typical… | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.9.9.98.1.1.1.1.2 |
| pagpPhysGroupCapability The values in pagpPhysGroupCapability indicate the aggregation
capability of the underlying hardware.
The speed, configuration, and status condition of the interfac… | column | PagpGroupCapability | .1.3.6.1.4.1.9.9.98.1.1.1.1.3 |
| pagpOperGroupCapability This variable informs the system administrator examining the
Fast
Etherchannel MIB of the capabilities of the current state of the
interface's hardware to form agports.
… | column | PagpGroupCapability | .1.3.6.1.4.1.9.9.98.1.1.1.1.4 |
| pagpAdminGroupCapability pagpAdminGroupCapability is used by the network administrator
to
control the aggregation of interfaces into agports. The default
value of pagpAdminGroupCapability is equal to the… | column | PagpGroupCapability | .1.3.6.1.4.1.9.9.98.1.1.1.1.5 |
| pagpLearnMethod This interface's learning method value. Specifies whether this
device is able to learn the location of a source MAC address
based
on the agport on which it was received, agPort(2… | column | PagpLearnMethod | .1.3.6.1.4.1.9.9.98.1.1.1.1.7 |
| pagpGroupIfIndex If pagpGroupIfIndex is 0, then the inteface is not aggregated
to an agport, and is unavailable for normal data reception and
transmission.
If pagpGroupIfIndex equal… | column | CISCO-TCInterfaceIndexOrZero | .1.3.6.1.4.1.9.9.98.1.1.1.1.8 |
| pagpDistributionProtocol pagpDistributionProtocol controls the load balancing
algorithms used on this interface's agport to distribute
outgoing data frames among its component interfaces, such
as IP addr… | column | Enumeration | .1.3.6.1.4.1.9.9.98.1.1.1.1.9 |