pagpPhysGroupCapability
CISCO-PAGP-MIB ·
.1.3.6.1.4.1.9.9.98.1.1.1.1.3
Object
column
PagpGroupCapability
The values in pagpPhysGroupCapability indicate the aggregation
capability of the underlying hardware.
The speed, configuration, and status condition of the interface,
e.g. ISL protocol on/off, ifOperStatus On/Off,
full-/half-duplex,
etc., does not affect the state of pagpPhysGroupCapability.
Any number of interfaces with the same value of
pagpPhysGroupCapability can be aggregated together manually.
Context
- MIB
- CISCO-PAGP-MIB
- OID
.1.3.6.1.4.1.9.9.98.1.1.1.1.3- Type
- column
- Access
- readonly
- Status
- current
- Parent
- pagpEtherChannelEntry
- Table
- pagpEtherChannelTable
- Siblings
- 11
Syntax
PagpGroupCapability
- Source
- PagpGroupCapability
- Base type
Integer32
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| pagpEthcOperationMode The managed device will refuse a request to set
pagpEthcOperationMode to the pagpOn(3) state if the device does
not implement the PAgP protocol. The managed device will refuse
to… | column | PagpEthcOperationMode | .1.3.6.1.4.1.9.9.98.1.1.1.1.1 |
| pagpDistributionAddress pagpDistributionAddress controls the type of distribution
on the configured pagpDistributionProtocol used on this
interface's agport to distribute outgoing data frames among its
… | column | Enumeration | .1.3.6.1.4.1.9.9.98.1.1.1.1.10 |
| pagpRate Specifies the rate at which the PAgP packets are transmitted
on this interface.
fast(1) : PAgP packets are transmitted at the fast rate
on this interface.
norm… | column | Enumeration | .1.3.6.1.4.1.9.9.98.1.1.1.1.11 |
| pagpInPacketTimeout Specifies the earliest time at which received PAgP
information packets are timed out. | column | Seconds Unsigned32 | .1.3.6.1.4.1.9.9.98.1.1.1.1.12 |
| pagpDeviceId Uniquely identifies a device which implements Fast
Etherchannel.
The combination of pagpDeviceId and ifIndex must be unique over
all interfaces in a network. pagpDeviceId typical… | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.9.9.98.1.1.1.1.2 |
| pagpOperGroupCapability This variable informs the system administrator examining the
Fast
Etherchannel MIB of the capabilities of the current state of the
interface's hardware to form agports.
… | column | PagpGroupCapability | .1.3.6.1.4.1.9.9.98.1.1.1.1.4 |
| pagpAdminGroupCapability pagpAdminGroupCapability is used by the network administrator
to
control the aggregation of interfaces into agports. The default
value of pagpAdminGroupCapability is equal to the… | column | PagpGroupCapability | .1.3.6.1.4.1.9.9.98.1.1.1.1.5 |
| pagpPortPriority The priority of this interface relative to other interfaces
when determining which interface is to be used in Hot
Standby mode.
Among all interfaces aggregated toge… | column | PagpPortPriority | .1.3.6.1.4.1.9.9.98.1.1.1.1.6 |
| pagpLearnMethod This interface's learning method value. Specifies whether this
device is able to learn the location of a source MAC address
based
on the agport on which it was received, agPort(2… | column | PagpLearnMethod | .1.3.6.1.4.1.9.9.98.1.1.1.1.7 |
| pagpGroupIfIndex If pagpGroupIfIndex is 0, then the inteface is not aggregated
to an agport, and is unavailable for normal data reception and
transmission.
If pagpGroupIfIndex equal… | column | CISCO-TCInterfaceIndexOrZero | .1.3.6.1.4.1.9.9.98.1.1.1.1.8 |
| pagpDistributionProtocol pagpDistributionProtocol controls the load balancing
algorithms used on this interface's agport to distribute
outgoing data frames among its component interfaces, such
as IP addr… | column | Enumeration | .1.3.6.1.4.1.9.9.98.1.1.1.1.9 |