CISCO-ASPP-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
1
Rows
1
Columns
17

asppPortTable

table
.1.3.6.1.4.1.9.9.55.1.1.1 · 1 row entry · 17 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk asppPortTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ASPP-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ASPP-MIB::asppPortTable' 
A list of asynchronous interfaces which have been 
configured to support an asynchronous security protocol
(ASP) BSTUN group.
asppPortEntry row .1.3.6.1.4.1.9.9.55.1.1.1.1
Current ASP configuration settings for an asynchronous
port.
Indexes
Column Syntax OID
asppPortProtocol
Specifies type of asynchronous security protocol being
used. These protocols are implemented by individual
security alarm manufacturers. There is no standard
protocol for alarm communications over RS-232
interfaces.
…
Enumeration
Enumerated Values:
1adplex
2adtPollSelect
3adtVariPoll
4diebold
5asyncGeneric
6mdi
7mosec
8gddb
9apos
 .1.3.6.1.4.1.9.9.55.1.1.1.1.1
asppPortRole
Specifies the router's protocol role.
primary(1) - Indicates we are attaching to the terminal
or alarm panel.
secondary(2) - Indicates we are attaching to the host
or alarm console..
Enumeration
Enumerated Values:
1primary
2secondary
 .1.3.6.1.4.1.9.9.55.1.1.1.1.2
asppPortReceiveInterFrameTimeout
Specifies the receive inter-frame-timeout period, used
to delimit frames. Since all the protocols are
implemented over RS-232 3-wire circuits (ie TX, RX and
GND), the only general method for start-end frame
detection i…
millisecondsInteger32
Constraints:
range: 0-1000
 .1.3.6.1.4.1.9.9.55.1.1.1.1.3
asppPortDeviceAddressOffset
Specifies the byte offset within a frame, which
contains the device address. This is used when the
asynchronous interface is configured to use the async
generic protocol handler. Because no knowledge of the
protocol …
bytesInteger32
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.55.1.1.1.1.4
asppPortEOFCharacter
Specifies the protocol character to use to delimit
the end of a frame. The valid character is 0-255 and
256 indicates the object is not configured.
Integer32
Constraints:
range: 0-256
 .1.3.6.1.4.1.9.9.55.1.1.1.1.5
asppPortSOFCharacter
Specifies the protocol character to use to delimit
the beginning of a frame. The valid character is 0-255
and 256 indicates the object is not configured.
Integer32
Constraints:
range: 0-256
 .1.3.6.1.4.1.9.9.55.1.1.1.1.6
asppPortIgnoreSequenceNumber
Specifies whether the asp sequence numbers used to
synchronize aspp traffic between head-end and tail-end
routers should be ignored. This is enabled if there
isn't a one to one correlation between commands and
response…
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.9.9.55.1.1.1.1.7
asppPortRspTimer
Specifies the amount of time the router will wait for a
response to a packet before retransmission.
secondsInteger32
Constraints:
range: 1-30
 .1.3.6.1.4.1.9.9.55.1.1.1.1.8
asppPortRxTimer
Specifies the maximum amount of time the router will
wait for a complete packet to be received. It starts
when an STX character is received.
secondsInteger32
Constraints:
range: 10-60
 .1.3.6.1.4.1.9.9.55.1.1.1.1.9
asppPortHostTimer
Specifies the maximum amount of time the router will
wait for a response to a terminal request from the
host. It starts when a terminal request is forwarded
to the host.
secondsInteger32
Constraints:
range: 10-120
 .1.3.6.1.4.1.9.9.55.1.1.1.1.10
asppPortConnectTimer
Specifies the maximum amount of time the router will
wait for the activation of the tunnel connection to the
host to complete. It starts when a terminal requests a
session with host.
secondsInteger32
Constraints:
range: 1-30
 .1.3.6.1.4.1.9.9.55.1.1.1.1.11
asppPortRetryCount
Specifies the maximum number of timers a packet will be
retransmitted before the connection with the terminal
will be disconnected.
Integer32
Constraints:
range: 1-10
 .1.3.6.1.4.1.9.9.55.1.1.1.1.12
asppPortDelayEnq
Specifies the amount of time to wait after sending a
connect packet to the the terminal before sending the
ENQ to initiate a session
millisecondsInteger32
Constraints:
range: 1-1000
 .1.3.6.1.4.1.9.9.55.1.1.1.1.13
asppPortDisableEnq
Specifies whether sending of ENQ to initiate a session
with the terminal is disabled.
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.9.9.55.1.1.1.1.14
asppPortSendAck
Specifies whether the router will send an ACK to
acknowledge packets.
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.9.9.55.1.1.1.1.15
asppPortDirect
Specifies whether the line mode is direct or dialed.
If in direct the router will immediately send ENQ
without waiting for AT commands
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.9.9.55.1.1.1.1.16
asppPortDCDAlways
Specifies whether DCD should always be asserted or
asserted only when the connection is active.
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.9.9.55.1.1.1.1.17