asppPortIgnoreSequenceNumber
CISCO-ASPP-MIB ·
.1.3.6.1.4.1.9.9.55.1.1.1.1.7
Object
column
SNMPv2-TCTruthValue
Specifies whether the asp sequence numbers used to synchronize aspp traffic between head-end and tail-end routers should be ignored. This is enabled if there isn't a one to one correlation between commands and responses between the two routers.
Context
- MIB
- CISCO-ASPP-MIB
- OID
.1.3.6.1.4.1.9.9.55.1.1.1.1.7- Type
- column
- Access
- readonly
- Status
- current
- Parent
- asppPortEntry
- Table
- asppPortTable
- Siblings
- 16
Values & Constraints
Type Values
1 | true |
2 | false |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| asppPortProtocol Specifies type of asynchronous security protocol being
used. These protocols are implemented by individual
security alarm manufacturers. There is no standard
protocol for alarm c… | column | Enumeration | .1.3.6.1.4.1.9.9.55.1.1.1.1.1 |
| asppPortHostTimer Specifies the maximum amount of time the router will
wait for a response to a terminal request from the
host. It starts when a terminal request is forwarded
to the host. | column | seconds Integer32 | .1.3.6.1.4.1.9.9.55.1.1.1.1.10 |
| asppPortConnectTimer Specifies the maximum amount of time the router will
wait for the activation of the tunnel connection to the
host to complete. It starts when a terminal requests a
session with h… | column | seconds Integer32 | .1.3.6.1.4.1.9.9.55.1.1.1.1.11 |
| asppPortRetryCount Specifies the maximum number of timers a packet will be
retransmitted before the connection with the terminal
will be disconnected. | column | Integer32 | .1.3.6.1.4.1.9.9.55.1.1.1.1.12 |
| asppPortDelayEnq Specifies the amount of time to wait after sending a
connect packet to the the terminal before sending the
ENQ to initiate a session | column | milliseconds Integer32 | .1.3.6.1.4.1.9.9.55.1.1.1.1.13 |
| asppPortDisableEnq Specifies whether sending of ENQ to initiate a session
with the terminal is disabled. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.55.1.1.1.1.14 |
| asppPortSendAck Specifies whether the router will send an ACK to
acknowledge packets. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.55.1.1.1.1.15 |
| asppPortDirect Specifies whether the line mode is direct or dialed.
If in direct the router will immediately send ENQ
without waiting for AT commands | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.55.1.1.1.1.16 |
| asppPortDCDAlways Specifies whether DCD should always be asserted or
asserted only when the connection is active. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.55.1.1.1.1.17 |
| asppPortRole Specifies the router's protocol role.
primary(1) - Indicates we are attaching to the terminal
or alarm panel.
secondary(2) - Indicates we are attaching to the host … | column | Enumeration | .1.3.6.1.4.1.9.9.55.1.1.1.1.2 |
| asppPortReceiveInterFrameTimeout Specifies the receive inter-frame-timeout period, used
to delimit frames. Since all the protocols are
implemented over RS-232 3-wire circuits (ie TX, RX and
GND), the only general… | column | milliseconds Integer32 | .1.3.6.1.4.1.9.9.55.1.1.1.1.3 |
| asppPortDeviceAddressOffset Specifies the byte offset within a frame, which
contains the device address. This is used when the
asynchronous interface is configured to use the async
generic protocol handler… | column | bytes Integer32 | .1.3.6.1.4.1.9.9.55.1.1.1.1.4 |
| asppPortEOFCharacter Specifies the protocol character to use to delimit
the end of a frame. The valid character is 0-255 and
256 indicates the object is not configured. | column | Integer32 | .1.3.6.1.4.1.9.9.55.1.1.1.1.5 |
| asppPortSOFCharacter Specifies the protocol character to use to delimit
the beginning of a frame. The valid character is 0-255
and 256 indicates the object is not configured. | column | Integer32 | .1.3.6.1.4.1.9.9.55.1.1.1.1.6 |
| asppPortRspTimer Specifies the amount of time the router will wait for a
response to a packet before retransmission. | column | seconds Integer32 | .1.3.6.1.4.1.9.9.55.1.1.1.1.8 |
| asppPortRxTimer Specifies the maximum amount of time the router will
wait for a complete packet to be received. It starts
when an STX character is received. | column | seconds Integer32 | .1.3.6.1.4.1.9.9.55.1.1.1.1.9 |